SAA-122100 [SII]
Single-Mode FC ADAPTOR supplied; 单模光纤通道适配器供电型号: | SAA-122100 |
厂家: | SEIKO INSTRUMENTS INC |
描述: | Single-Mode FC ADAPTOR supplied |
文件: | 总9页 (文件大小:68K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DOCUMENT NUMBER NCD-5DC2-01
SAA-1 Series
Single-Mode
FC ADAPTOR
TECHNICAL SPECIFICATIONS
Seiko Instruments Inc.
Components Sales Dept.
8, Nakase 1-Chome
Mihama-ku, Chiba-shi, Chiba-ken
261 JAPAN
Telephone : 043-211-1214
-1215
Facsimile : 043-211-8035
SAA-1 Series Single-Mode FC ADAPTOR
TECHNICAL SPECIFICATIONS
Document Number NCD-5DC2-01
NAE63D01 " SAA-1 Part " May 1986
NAE63D02 " SAA-1 Part " September 1986
SSA930305
March 1993
39055-2016-01
NCD-5DC2-01
September 1993
December 1995
Copyright 1986, 1993, 1995 by Seiko Instruments Inc.
All right reserved.
The information contained herein shall not reproduced or disclosed to any third party
without the express written consent of SII.
The Specifications contained herein are subject to change without notice.
SII is a trademark of Seiko Instruments Inc.
Please address any questions, comments, and suggestions to:
Seiko Instruments USA Inc.
Electronics Components Division
2990 West Lomita Boulevard
Torrance, CA 90505, U.S.A.
Phone: 310-517-7780
Seiko Instruments GmbH
OFC Division
Siemensstraße 9b
D-63263 Neu-Isenburg, Germany
Phone: 06102-297-0
Fax: 06102-297-211
Fax: 310-517-7792
Seiko Instruments (H.K.) Ltd.
Sales Department
Seiko Instruments Taiwan Inc.
Sales Department
4th & 5th Floor, Wyler Center 2
200 Tai Lin Pai Road, Kwai Chung
N.T., Kowloon, Hong Kong
Phone: 852-2421-8611
5F-1, No.99, Sec. 2, Chung Shan
Rd.
Taipei 104, Taiwan, R.O.C.
Phone: 02-563-5001, 523-5111
Fax: 02-521-9519
Fax: 852-2480-5479
Seiko Instruments Singapore pte. Ltd.
2, Marsiling Lane,
Woodlands New Town,
Singapore, 2573, Singapore
Phone: 65-2691370
Fax: 65-2699729
ii
TABLE OF CONTENTS
Section
Page
1.
PROVISION
1
1
1
2
2
2
2
3
3
3
1.1
2.
Application Limit
PARTS NUMBER
3.
GENERAL SPECIFICATIONS
Parts and Materials
Physical Dimensions
General Tolerances
Insertion Loss
3.1
3.2
3.3
3.4
4.
PACKING
5.
SHIPPING INSPECTION
Table
Table 1
Table 2
Table 3
Table 4
Parts Number
1
2
2
3
Parts and Materials
General Tolerance
Insertion Loss and the Measurement Conditions
Figure
Figure 1
Insertion Loss Measurement System
SAA-1 Adaptor
3
4
5
Figure 2
Figure 3 to 4
Part Dimensions
iii
iv
1.
PROVISION
1.1 Application Limit
These specifications apply to the SAA-1 Single-Mode FC ADAPTOR supplied by SII.
2.
PARTS NUMBER
Parts Number of the Adaptor is Shown in Table 1.
Table 1 Parts Number
1
3.
GENERAL SPECIFICATIONS
3.1 Parts and Materials
Parts and the materials are shown in Table 2.
Table 2 Parts and materials
No.
①
Part Name
Housing A
Q'ty
Material
Notes
1
2
Brass
Nickel Plating
Nickel Plating
Fitting Sleeve
Brass
②
➂-1
➂-2
➃
Phosphor Bronze
Zirconia Ceramics
Brass
--
Slit Sleeve
1
Spacer
1
1
2
Nickel Plating
Nickel Plating
Nickel Plating
White
Housing B
Screw
Brass
⑤
Brass
➅
⑦-1
⑦-2
Plastic
Cap
2
Synthetic Rubber
Red
3.2 Physical Dimensions
Figure 2 shows the SAA-1.
Figure 3 to 4 show the part dimension.
• In accordance with JIS C5970 F01 type connectors
3.3 General Tolerances
Permissible deviation in dimensions without tolerance indication is in accordance with
JIS B 0405 class m, as shown in Table 3.
Table 3 General tolerance (JIS B 0405 class m)
Basic size step (mm)
Permissible deviation (mm)
Over
0.5
3
Under
3
±0.1
±0.1
±0.2
±0.3
6
6
30
30
120
2
3.4 Insertion Loss
Insertion Loss of the adaptor and the measurement conditions shown in Table 4.
Figure 1 shows the measurement system.
Measured Adaptor
Master Cord
Master Plug
Light-Source
Master Plug
Master Cord
Optical
Power Meter
Photo Detector
Figure 1 Insertion loss measurement system
Table 4 Insertion loss and the measurement conditions
SAA-1 1❑❑00
SAA-1 2❑❑00
Parts Number
Insertion Loss
( Slit Sleeve : Phosphor Bronze ) ( Slit Sleeve : Zirconia Ceramics )
0.7dB or Less
0.4dB or Less
Light-Source
LD or LED
LD
Wavelength
1.3 µm
1.3 µm
Conditions
Master Cord
Terminated
Flat Polishing with Buffing
PC Polishing
4.
PACKING
The product is packed to prevent damage during shippment.
5.
SHIPPING INSPECTION
The insertion loss inspected before shipping.
3
with Marking ( ROGO ) Type
without Marking ( ROGO ) Type
Unit : mm
FIgure 2 SAA-1
4
Unit : mm
Figure 3 ⑦-1 Cap
Unit : mm
Figure 4 ⑦-2 Cap
5
相关型号:
©2020 ICPDF网 联系我们和版权申明