SI2707-A10 [SILICON]
EMI MITIGATING 2.1X 5 W CLASS D AUDIO AMPLIFIER; EMI减轻2.1X 5瓦D类音频放大器型号: | SI2707-A10 |
厂家: | SILICON |
描述: | EMI MITIGATING 2.1X 5 W CLASS D AUDIO AMPLIFIER |
文件: | 总46页 (文件大小:608K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Si2704/05/06/07-A10
EMI MITIGATING 2.1X 5 W CLASS D AUDIO AMPLIFIER
Features
Digital input Delta-Sigma PWM
Patent-pending EMI mitigation
AM radio band noise-free notch
GSM/iPhone friendly
Wideband PWM carrier spreading
Power stage slew rate control
Power stage feedback for PSR/THD
Programmable 7 band parametric EQ,
dynamic range compressor, tone control
Crossbar input mixer with scaling
Digital tone and alert generation
128 dB volume control in 0.5 dB steps
Multiple low power operating modes
Over-current and over-temperature
detection w/ auto recovery
2x 5 W @ 3
BTL; 2x 3 W @ 8 BTL
88% efficiency with >50 dB PSRR
95 dB dynamic range and <0.1% THD
Stereo PWM DAC line analog outputs
Pop and click free operation
Standard 2-wire control w/ 2 addresses
System flexibility w/ 3 multi-function pins
Dual supply voltage: 2.7–3.6 V main
and 4.0–6.6 V power stage
Available in 4x4 24-pin Power QFN and
7x7 48-pin Power eTQFP package
Both Pb-free/RoHS compliant
Ordering Information:
2
See page 37.
Master/slave I S w/ 3 inputs & 1 output
Automatic digital audio rate detection
Standard audio rates from 32–192 kHz
Audio activity detector w/ auto-standby
Operates from external XTAL or clock
Buffered master/regulator clock output
Pin Assignments
Si2704/05/06/07
Applications
PMP/MP3 docking stations
Portable consumer audio electronics
Table top and portable radios
Active/wireless speakers
TVs and monitors
TV sound bars
24 23
22
21
20
19
DCLK
DIN
1
2
3
4
5
6
18 OUTPL
17 OUTNL
16 GNDL
15 GNDR
14 OUTNR
13 OUTPR
Description
VIO
GND PAD
(Back Paddle)
SCLK
SDIO
CLKO
The Si2704/05/06/07 EMI mitigating 2.1 digital audio processing Class D
amplifier integrates a power stage, PWM DAC, and digital audio processing
(DAP) for simplified, low cost, power efficient system designs in consumer
audio electronics. The digital input amplifier features delta-sigma PWM and
innovative EMI mitigation technology for producing high-quality audio while
effectively managing PWM switching noise for enhanced EMI compliance and
AM/FM radio co-existence, while also being GSM/iPhone friendly.
Top Down View
24-Pin QFN Package
7
8
9
10
11
12
Functional Block Diagram
48 47 46 45 44 43 42 41 40 39 38 37
1
36
35
34
33
32
31
30
29
28
27
26
25
NC
NC
Si270x Digital Class-D Amplifier
LDO
2
3
VPPL
OUTPL
GND
DFS
DCLK
DIN
VDD
2.7 – 3.6 V
Supply
4
Power
Stage
5
VIO
OUTNL
GNDL
GNDR
OUTNR
GND
Clock
Generation
6
GND
SCLK
SDIO
CLKO
NC
CH 1
LF
GND PAD
(Back Paddle)
7
PWM
CLKO
8
9
DSP
I2S/AAD
10
11
12
OUTPR
VPPR
NC
NC
Mixer
ASRC
4.0 – 6.6 V
Supply
Top Down View
48-Pin eTQFP Package
I2S
Feedback
NC
VPP
13 14 15 16 17 18 19 20 21 22 23 24
Tone Gen.
Cross-over Filter
Volume Control
Tone Control
7-Band EQ
DRC
Power
Stage
RF
VIO
1.62 – 3.6 V
Supply
CH 2
PWM
MFP
MFP Control
Over Current
Over Temp
AUXOL/R
2-Wire Control
System Control
PWM DAC
Rev. 0.6 8/10
Copyright © 2010 by Silicon Laboratories
Si2704/05/06/07-A10
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Si2704/05/06/07-A10
2
Rev. 0.6
Si2704/05/06/07-A10
TABLE OF CONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3. Typical System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.1. PWM Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4.1.1. PWM Switching Rate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1.2. EMI Mitigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.2. Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
4.2.1. Active Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2.2. Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2.3. Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2.4. Power Down Mode and Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.3. Chip Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
4.3.1. Multi-Function Pins (MFPs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.3.2. Output Mode Configuration (Si2705/07 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.4. Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4.4.1. Reference Clock Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.4.2. Reference Clock Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.5. Digital Audio I2S Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.5.1. Auto-Rate Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5.2. Audio Activity Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5.3. Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5.4. Audio data formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2
4.5.5. I S Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6. Digital Audio Processing (DAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
4.6.1. Parametric Equalization (Si2706/07 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.6.2. Tone Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.6.3. De-Emphasis (Si2706/07 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.6.4. Crossover Filter (Si2706/07 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.6.5. Digital Volume Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.6.6. Dynamic Range Compression (Si2706/07 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.6.7. Hard Signal Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.6.8. DC Notch Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.6.9. Tone and Alert Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.7. Fault Detection and Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.8. Power Supply and Grounding Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.9. Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.10. Programming with Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5. Commands and Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
6. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6.1. 24-Pin QFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6.2. 48-Pin eTQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
7. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
8. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Rev. 0.6
3
Si2704/05/06/07-A10
8.1. 24-Pin QFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
8.2. 48-Pin eTQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
9. Package Markings (Top Marks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
9.1. Si2707 Top Mark (QFN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
9.2. Top Mark Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
9.3. Si2707 Top Mark (eTQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
9.4. Top Mark Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
10. Additional Reference Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4
Rev. 0.6
Si2704/05/06/07-A10
1. Electrical Specifications
Table 1. Recommended Operating Conditions1
Parameter
Power Output Supply Voltage
Main Supply Voltage
Symbol
Test Condition
Min
Typ
—
Max
6.6
3.6
3.6
—
Unit
V
2
V
4.0
PP
DD
IO
V
V
2.7
1.62
—
3.3
—
V
Interface (I/O) Supply Voltage
Load Impedance
V
R
3–8
25
Ω
L
Ambient Temperature
Junction Temperature
Case Delta from Junction
T
–20
—
85
°C
°C
°C/W
A
T
—
135
5
J
Temperature delta between junc-
tion and top center of package
—
—
JC
3
Delta from Junction to Ambient
QFN package
eTQFP
—
—
25
30
—
—
°C/W
°C/W
JA
Notes:
1. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions.
Typical values apply at VDD = 3.3 V and 25 °C unless otherwise stated. Parameters are tested in production unless
otherwise stated.
2. Operation with VPP as low as 3 V is possible at reduced performance.
3. The is layout-dependent; therefore, PCB layout must provide adequate heat-sink capability. The. is specified,
JA
JA
assuming adequate ground plane as in “AN470: 270x Layout Guidelines.”
Table 2. Absolute Maximum Ratings1
Parameter
Power Output Supply Voltage
Main Supply Voltage
Symbol
Value
–0.5 to 7.0
–0.5 to 3.9
–0.5 to 3.9
10
Unit
V
V
PP
DD
IO
V
V
V
Interface (I/O) Supply Voltage
V
2
Input Current
I
mA
V
IN
2
Input Voltage
V
–0.3 to (V + 0.3)
IN
IO
Operating Temperature
Junction Temperature
Storage Temperature
Notes:
T
–20 to +85
150
°C
°C
°C
A
T
J
T
–55 to +150
A
1. Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation
should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure beyond
recommended operating conditions for extended periods may affect device reliability.
2. For input pins SCLK, SDIO, DCLK, DFS, DIN, RST, OUTSEL, MFPx.
Rev. 0.6
5
Si2704/05/06/07-A10
Table 3. DC Characteristics—Supplies and Interfaces
(VDD = 2.7 to 3.6 V, VIO = 1.62 to 3.6 V, VPP = 4 to 6.6 V, TA = –20 to +85 °C)
Parameter
Start Up Time
Symbol
Test Condition
Min
Typ
Max
Unit
T
From Standby Mode
with CLKO enabled
—
—
2
ms
ONSB
From Standby Mode
with CLKO disabled
—
—
20
ms
T
From Sleep Mode
—
—
—
—
—
50
20
200
—
ms
ms
mA
ON_SLP
T
From Power Down Mode
ON_PD
Active Mode Quiescent
Supply Current
I
From V , No load, Both Chan-
PQ
PP
nels Active, Spread Mode PWM
From V , No load, Both Chan-
—
45
—
mA
PP
nels Active, Normal Mode PWM
I
From V
—
—
54
—
—
mA
mA
DQ
DD
2
I
From V I S Slave Mode,
1.3
IOQ
IO,
CLKO Disabled
Standby Mode Supply
Current
I
Standby Mode
—
—
0.1
8
—
—
mA
mA
PSTB
I
Standby Mode
DSTB
with CLKO enabled
Standby Mode
—
4
—
mA
with CLKO disabled
I
Standby Mode
SLEEP asserted
SLEEP asserted
SLEEP asserted
—
—
—
—
—
—
—
2
—
—
—
—
—
—
—
mA
mA
mA
mA
mA
mA
mA
IOSTB
Sleep Mode Supply
Current
I
0.1
2
PSLP
DSLP
IOSLP
I
I
1.5
0.1
2
Power Down Mode Supply
Current
I
PPD
DPD
I
I
0.3
IOPD
Input pins SCLK, SDIO, DCLK, DFS, DIN, RST, OUTSEL, MFPx
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
V
0.7 x V
—
—
—
—
—
—
0.3 x V
10
V
V
IH
IO
V
IL
IO
I
V
= V = 3.6 V
–10
μA
μA
IH
IN
IO
I
V
= 0 V, V = 3.6 V
–10
10
IL
IN
IO
Output pins MFPx, CLKO*
High Level Output Voltage
Low Level Output Voltage
High Level Output Current
Low Level Output Current
V
I
= 500 μA
0.8 x V
—
—
—
6
—
V
V
OH
OUT
IO
V
I
= –500 μA
0.2 x V
—
OL
OUT
IO
I
0.8 x V
0.2 x V
—
mA
mA
OH
IO
IO
I
—
6
—
OL
*Note: Valid for the configuration where MFPx is configured as an output or general purpose output.
6
Rev. 0.6
Si2704/05/06/07-A10
Table 4. DC Characteristics—Class D Amplifier
(VDD = 2.7 to 3.6 V, VIO = 1.62 to 3.6 V, VPP = 4 to 6.6 V, TA = –20 to +85 °C)
Parameter
Symbol
Test Condition
Min
—
Typ
±10
648
Max
—
Unit
mV
Output Voltage Offset
V
Differential Output
OS
Total Drain-Source On-State
Resistance (Total Bridge)*
R
V
= 6.6 V, I = 1A
—
—
mΩ
DSON
PP
O
*Note: Excludes package bond wire resistance.
Table 5. AC Characteristics—Class D Amplifier
(VDD = 2.7 to 3.6 V, VIO = 1.62 to 3.6 V, VPP = 6.6 V, RL = 8 Ω, VOL = 0 dBFS, TA = –20 to +85 °C, unless otherwise noted.)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
1
Continuous Output Power
P
THD+N = 10%, f = 1 kHz,
—
2.7
—
W
O
R = 8 Ω
L
THD+N = 1%, f= 1 kHz,
—
—
—
—
1.9
4.7
3.4
5.0
—
—
—
—
W
W
W
W
R = 8 Ω
L
THD+N = 10%, f = 1 kHz,
R = 4 Ω
L
THD+N = 1%, f= 1 kHz,
R = 4 Ω
L
THD+N = 10%, f = 1 kHz,
RL = 3 Ω
Total Harmonic Distortion + Noise
THD+N
SNR
P =1 W, f = 1 kHz
—
—
0.1
95
—
—
%
O
Signal to Noise Ratio/Dynamic
Range
Normal mode PWM,
f = 1 kHz, A-weighted
dB
Normal mode PWM,
f = 1 kHz, Unweighted
—
—
—
—
—
92
90
87
24
35
—
—
—
—
—
dB
dB
dB
dB
dB
Spread mode PWM,
f = 1 kHz, A-weighted
Spread mode PWM,
f = 1 kHz, Unweighted
Spread Mode Common Mode PWM
f = 1 kHz,
Relative to Normal Mode
2
Carrier Peak Attenuation
Common Mode AM Band Noise
f = 1 kHz,
3
Notch Attenuation
Measured in ±10 kHz band
around selected frequency
Notes:
1. Measured at filter output. Power measured at the chip output is greater.
2. Guaranteed by characterization.
3. Measured relative to the integrated noise floor in Spread mode. Guaranteed by characterization.
4. Does not include filter efficiency losses.
Rev. 0.6
7
Si2704/05/06/07-A10
Table 5. AC Characteristics—Class D Amplifier (Continued)
(VDD = 2.7 to 3.6 V, VIO = 1.62 to 3.6 V, VPP = 6.6 V, RL = 8 Ω, VOL = 0 dBFS, TA = –20 to +85 °C, unless otherwise noted.)
Power Supply Rejection Ratio
PSRR
P = –3 dBFS, f = 1 kHz;
—
50
—
dB
O
200 mV , f = 400 Hz
PP
r
supply ripple
Crosstalk
f = 1 kHz
—
—
–92
88
—
—
dB
%
4
Efficiency
η
f = 1 kHz, half rate PWM and
10 ns slew rate
Output Pulse Repetition Frequency
PRF
Half Rate PWM
Full Rate PWM
—
—
480
960
—
—
kHz
kHz
Notes:
1. Measured at filter output. Power measured at the chip output is greater.
2. Guaranteed by characterization.
3. Measured relative to the integrated noise floor in Spread mode. Guaranteed by characterization.
4. Does not include filter efficiency losses.
Table 6. AC Characteristics—PWM Digital to Analog Converter
(VDD = 2.7 to 3.6 V, VIO = 1.62 to 3.6 V, VOL = 0 dBFS, TA = -20 to +85 °C, unless otherwise noted).
Parameter
Symbol
THD+N
SNR
Test Condition
f = 1 kHz
Min
—
—
—
—
—
5
Typ
0.02
88
Max Unit
Total Harmonic Distortion + Noise
Signal to Noise Ratio/Dynamic Range
—
—
—
—
—
50
1
%
f = 1 kHz, A-weighted
f = 1 kHz, Unweighted
dB
dB
85
Output Voltage Swing
Vout
1
V
P-P
Output Voltage Common Mode Bias
Output Load— Resistance
Output Load— Capacitance
Voutcm
0.8
—
V
R
C
AC coupled
kΩ
load
load
AC coupling capacitor
0.1
—
µF
Table 7. I2S Digital Audio Interface Characteristics
(VIO = 1.62 to 3.6 V, TA = –20 to +85 °C, unless otherwise noted).
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
DCLK Input Cycle Time
DCLK Input Pulse Width High
t
70
—
—
—
ns
ns
CYC:DCLK
t
0.4 x
0.6 x
HI:DCLK
t
t
t
t
CYC:DCLK
CYC:DCLK
DCLK Input Pulse Width Low
t
0.4 x
—
0.6 x
ns
LO:DCLK
CYC:DCLK
CYC:DCLK
DFS Setup Time to DCLK↑
DFS Hold Time after DCLK↑
DOUT Output Delay
t
10
5
—
—
—
—
—
—
35
15
ns
ns
ns
pF
SU:DCLK
t
HD:DCLK
T
0
PD:DCLK
Capacitive Loading
C
—
B
8
Rev. 0.6
Si2704/05/06/07-A10
Figure 1. Digital Audio Timing Parameters
Table 8. 2-Wire Control Interface Characteristics
(VIO = 1.62 to 3.6 V, TA = –20 to +85 °C, unless otherwise noted).
Parameter
Symbol
Test
Min
Typ
Max
Unit
Condition
SCLK Frequency
f
0
—
—
—
—
400
—
kHz
µs
SCL
SCLK Low Time
SCLK High Time
t
1.3
0.6
0.6
LOW
t
—
µs
HIGH
SCLK Input from SDIO Setup ↓
t
—
µs
SU:STA
(START)
SCLK Input to SDIO ↓ Hold (START)
t
t
0.6
—
—
µs
HD:STA
SDIO Input to SCLK ↑ Setup
SDIO Input to SCLK ↓ Hold
SDIO output delay
100
0
—
—
—
—
—
900
900
—
ns
ns
ns
µs
SU:DAT
HD:DAT
t
T
300
0.6
PD:DAT
t
SU:STO
SCLK input to SDIO ↑ Setup (STOP)
STOP to START Time
t
1.3
—
—
—
—
—
µs
ns
ns
BUF
SDIO Output Fall Time
t
250
300
f:OUT
SDIO Input, SCLK Rise/Fall Time
t
t
—
f:IN
r:IN
Capacitive Loading
C
—
—
—
—
50
50
pF
ns
b
Pulse Width Rejected by Input Filter
t
SP
Rev. 0.6
9
Si2704/05/06/07-A10
Table 9. 2-Wire Control Interface Address Selection
CLKO Startup Voltage (Pin
2-Wire
Connection)
Device Address
GND
1001010 (0x94)
0011011 (0x36)
V
(Default)
IO
Table 10. Reset Timing Characteristics
(VIO = 1.62 to 3.6 V, TA = -20 to +85 °C, unless otherwise noted).
Parameter
Symbol
Test Condition
Min
Typ
—
Max
—
Unit
μs
CLKO Setup Time to RST↑
CLKO Hold Time after RST↑
t
100
30
SRST
T
—
—
ns
HRST
tHRST
tSRST
70%
RST
30%
70%
CLKO
30%
Figure 2. Reset Timing Parameters for Configuration Mode Select
10
Rev. 0.6
Si2704/05/06/07-A10
tSU:STA tHD:STA
tLOW
tHIGH
tr:IN
tf:IN
tSP
tSU:STO
tBUF
70%
30%
SCLK
SDIO
70%
30%
tf:IN,
tf:OUT
START
tHD:DAT tSU:DAT
tPD:DAT
tr:IN
STOP
START
Figure 3. 2-Wire Control Interface Read and Write Timing Parameters
SCLK
Command
7-0
Arg1
7-0
SDIO
(Write)
A6-A0, 0
START
ADDRESS + R/W
ACK
ACK
DATA
ACK
ACK
DATA
ACK
ACK
STOP
Status
7-0
Response
7-0
SDIO
(Read)
A6-A0, 1
START
ADDRESS + R/W
DATA
DATA
STOP
Figure 4. 2-Wire Control Interface Read and Write Timing Diagram
Rev. 0.6
11
Si2704/05/06/07-A10
Table 11. Reference Clock and Crystal Characteristics
(VDD = 2.7 to 3.6 V, VIO = 1.62 to 3.6 V, TA = –20 to +85 °C, unless otherwise noted).
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Reference Clock, Pin XTLI
1
Supported Frequencies
2
–1000
—
—
—
—
49
1000
50
MHz
ppm
Frequency Tolerance
2
Jitter Tolerance
Integrated from 20 Hz to
1 MHz
psrms
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
VIH
VIL
IIH
0.7xVI0
—
—
—
—
—
—
0.3xVI0
10
V
V
VIN = VI0 = 3.6 V
–10
μA
μA
IIL
VIN = 0 V
–10
10
VI0 = 3.6 V
Crystal oscillator, Pins XTLI, XTLO
3
Crystal Oscillator Frequency
12.288
–1000
4
—
—
—
—
24.576
1000
20
MHz
ppm
pF
Crystal Frequency Tolerance
Internal Crystal Load Capacitance
Crystal Motion Resistance
for 24.576 MHz Crystal
—
100
Reference Clock Output, Pin CLKO
4
Frequency Range
120
—
—
—
24576
10
kHz
pF
Load Capacitance
Notes:
1. Supported reference clock frequencies at XTLI include 2.048, 2.822, 3.072, 4.096, 4.234, 4.608, 5.645, 6.144, 8.192,
8.467, 9.216, 11.290, 11.2896, 12, 12.288, 16.368, 16.934, 18.432, 22.579, 24.576, 32.768, 32.869, 36.864, 45.158,
and 49.152 MHz.
2. Required to achieve specified performance.
3. Supported crystal frequencies at XTLI include 12.288, 18.432, and 24.576 MHz.
4. 120 kHz, 240 kHz, 480 kHz, 960 kHz, 1.92 MHz, 4.096 MHz, 6.144 MHz, 8.192 MHz, 12.288 MHz, 16.384 MHz, and
24.576 MHz are available at CLKO.
12
Rev. 0.6
Si2704/05/06/07-A10
2. Typical Application Schematic
VPP
VDD
4.0 to 6.6 V
2.7 to 3.6 V
C9
C11
0.1 uF
220 uF
C10
0.1 uF
C7
0.1 uF
VIO
1.62 to 3.6 V
Optional
L1
C8
C1
R1
0.1 uF
C15
C16
18
OUTPL
OUTNL
21
C5
XTLI
X1
17
22
XTLO
R2
C2
20
RSTB
16
15
24
1
U1
Si2705/07
GNDL
GNDR
L2
L3
DFS
DCLK
DIN
2
4
SCLK
SDIO
CLKO
13
14
OUTPR
OUTNR
5
C3
R3
6
C17
C18
C6
SLEEP/MFP3
AUXOL
R4
C4
L4
C12
C13
Figure 5. Typical Application Schematic
Table 12. Typical Application Schematic Bill of Materials
Component
C1, C2, C3, C4
C15, C16, C17, C18
C5, C6
Inductor Filter
0.68 µF, ceramic
0.33 µF, ceramic
0.47 µF, Film
Ferrite Bead Filter
1000 pF, ceramic
1000 pF, ceramic
100 pF, ceramic
L1, L2, L3, L4
10 µH, 1.5 A, inductor
TDK MPZ2012S601A,
ferrite bead
Note: When using the ferrite bead output filter with AM radio, shielded cable is
recommended.
Rev. 0.6
13
Si2704/05/06/07-A10
3. Typical System Configurations
VDD/VIO
VPP
2.7–3.6 V
Supply
4.0–6.6 V
Supply
XTLI
OUTPL
OUTNL
XTLO
LF
Dock
I/F
Dock
CLKO
Si270x
Digital Audio
Amplifier
I2S
Stereo
ADC
Line
In
OUTPR
OUTNR
RF
HPDET
OUTSEL
AUXOL
AUXOR
2-Wire
MFP
User I/F
System MCU
Figure 6. Basic PMP Dock System Configuration
VDD/VIO
VPP
2.7–3.6 V
Supply
4.0–6.6 V
Supply
XTLI
XTLO
CLKO
OUTPL
OUTNL
LF
Filter
I2S DI2
I2S DO
Digital Media
Controller
Si270x
Digital Audio
Amplifier
Dock
I/F
Dock
Radio Tuner
Si473x-D
I2S DIN
OUTPR
OUTNR
Filter
RF
Stereo
ADC
Line
In
2-Wire
MFP
AUXOL
AUXOR
User I/F
System MCU
HPDET
Figure 7. PMP Dock with Radio and Digital Media Controller System Configuration
14
Rev. 0.6
Si2704/05/06/07-A10
External Subwoofer
XTLI
AUXOL
XTLO
Digital
Media
Controler
I2S
Midrange
Amplifier
L
L Midrange
R Midrange
Si270x
R
I2C adress 0x36
OUTSEL
2-Wire
System
MCU
CLKO
XTLI
L
L Tweeter
Tweeter
Amplifier
R
R Tweeter
Si270x
OUTSEL
AUXOL
AUXOR
I2S
HPDET
Radio
I2C adress 0x94
Headphone
Figure 8. Stereo 2-Way Speaker System Configuration
External Subwoofer
AUXOL
1
XTLI
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
Si270x
Digital Audio
Amplifier
XTLO
2
Analog
Audio 1
CLKO
XTLI
Analog
Audio 2
Si270x
Digital Audio
Amplifier
1
2
Receiver & Mux
Audio Processor
Delay Control
Digital
Audio
XTLI
Si270x
Digital Audio
Amplifier
1
2
DVI/PC
Audio
From
PMP
dock
XTLI
Si270x
Digital Audio
Amplifier
1
2
Figure 9. TV Sound Bar System Configuration
Rev. 0.6
15
Si2704/05/06/07-A10
4. Functional Description
Si270x Digital Class-D Amplifier
VDD
2.7 – 3.6 V
Supply
LDO
Power
Stage
Clock
Generation
CH 1
LF
PWM
CLKO
DSP
I2S/AAD
Mixer
ASRC
4.0 – 6.6 V
Supply
I2S
Feedback
VPP
Tone Gen.
Cross-over Filter
Volume Control
Tone Control
7-Band EQ
DRC
Power
Stage
RF
VIO
1.62 – 3.6 V
Supply
CH 2
PWM
MFP
MFP Control
Over Current
Over Temp
AUXOL/R
2-Wire Control
System Control
PWM DAC
Figure 10. Functional Block Diagram
The Si2704/05/06/07 EMI mitigating 2.1 x 5 W Class D audio amplifier integrates a stereo power stage, PWM DAC,
and digital signal processor (DSP) to enable simplified, low cost, power efficient system designs in consumer audio
electronics. The digital input amplifier features delta-sigma PWM for high quality audio while innovative EMI
mitigation technology manages PWM switching noise to suppress peak emissions more than 20 dB while providing
co-existence with AM/FM radio tuners.
The power stage is capable of driving two 3 Ω bridge-tied speakers with 5 W per channel at 10% THD+N from
6.6 V power supplies. It can also drive 8 Ω bridge-tied speakers at 3 W per channel with 88% efficiency. The power
stage feedback systems improve power supply rejection and harmonic distortion performance.
2
The Si270x connects up to three synchronous I S digital sources as either master or slave, two of which can be
2
configured as input or output. The I S input is converted to a common sample rate for digital audio processing
using an asynchronous sample rate converter (ASRC) and a digital crossbar mixer linearly combines any of the six
inputs into the three audio processing channels
Integrated digital audio processing enables the amplifier to compensate for speaker and enclosure acoustic
characteristics. A programmable 7-biquad parametric equalizer for each main channel allows notching out of
mechanical resonances and pre-compensation of the speaker frequency response, while programmable dynamic
range compression protects from overdriving speakers and increases the average output power without increasing
apparent distortion. Tone control enables ±18 dB of treble and bass boost/cut, while output volume is digitally
2
controlled in 0.5 dB steps from –100 to +28 dB via the I C-Compliant 2-Wire interface or an analog potentiometer
connected to the integrated ADC. Two independent tone generators enable mixing of multi-tone alarms and alerts
into the audio channels.
The auxiliary audio processing channel (Aux Channel) with optional sub-mixing and low pass filtering generates
mono line level analog audio output for driving an external active subwoofer or center speaker. The main channel
L/R outputs may also be connected to the PWM DAC for driving a headphone amplifier.
A low jitter PLL generates internal system clocks referenced in master mode to an external crystal, or alternatively,
2
in slave mode to either the I S data clock (DCLK) or the audio master clock (MCLK). A buffered clock (CLKO) can
be output by the device to synchronously drive companion audio devices, additional amplifiers, and switching
regulators.
16
Rev. 0.6
Si2704/05/06/07-A10
4.1. PWM Processing
The Si270x is designed to operate using a bridge-tied-load (BTL) output configuration where both sides of the
speaker are actively driven by the amplifier.
4.1.1. PWM Switching Rate Control
The output PWM switching frequency can be programmed via 2-wire control to be half rate (480 kHz) or full rate
(960 kHz). The different rates can be configured by setting property PWM_FREQ.
Full Rate PWM provides better audio performance and AM radio co-existence, while Half Rate PWM provides
lower switching losses and lower switching energy harmonics at high frequencies. For each configuration, the
switching frequency can be offset slightly for FM band frequency planning flexibility.
4.1.2. EMI Mitigation
By nature, the switching characteristic of Class D amplifiers that provides high power efficiency also creates
harmonic spurs at multiples of the PWM switching rate that can radiate as EMI. Common mode PWM switching
from ground to the supply translates into a radiated pattern with large energy components at the fundamental and
odd harmonics of the switching frequency. Fast pulse edge transitions and differential mode ripple currents flowing
through inductor windings further contribute to radiated interference. To simplify design for EMI compliance and
radio receiver co-existence, the Si270x features EMI mitigation modes for managing the PWM switching noise,
including pulse edge slew rate control, common mode switching noise spectral shifting, and common mode
switching noise spectral spreading/shaping.
4.1.2.1. Slew Rate Control
Output pulse edge slew rate can be programmed via 2-Wire control for 10 ns or 20 ns (property
PWM_OUTPUT_SLEW_RATE). While faster transition times are favorable for higher efficiency, slower transition
times are favorable for EMI attenuation.
4.1.2.2. Spectral Shifting
The frequency locations for the PWM common mode switching energy can be shifted to facilitate frequency
planning. This spectral shifting is useful for example in radios to avoid radiating interference at frequencies where
the radio is being tuned.
When spectral shifting is programmed for Integer Mode PWM, the common mode switching energy and harmonics
are located at F x (2n–1) for all positive integers n, where Fc is the PWM switching frequency. Alternatively, when
C
programmed for Fractional Mode PWM, the common mode switching energy and harmonics are shifted down in
frequency by 50%, and are located at F x (2n–1)/2.
C
The spectral shifting mode can be programmed dynamically by setting property PWM_CONFIG during normal
operation without adversely affecting the internal audio processing or the amplified audio signal integrity.
Rev. 0.6
17
Si2704/05/06/07-A10
Figure 11. PWM CM Spectrum for Integer Mode PWM
Figure 12. PWM CM Spectrum for Fractional Mode PWM
4.1.2.3. Spectral Spreading
Spread mode PWM can be used to spread PWM common mode switching energy resulting in a peak energy
suppression greater than 20 dB at all frequencies. This Spectral Shaping feature is useful for mitigating EMI
radiation and eliminating inductors for filter-less applications. Spread Mode PWM can be programmed dynamically
by setting property PWM_CONFIG during normal operation without adversely affecting the internal audio
processing or the differential output signal integrity.
4.1.2.4. Spectral Shaping Noise-Free Notch for AM Radio (Si2705/07 only)
When using Spread Mode PWM with full rate PWM switching (960 kHz), a tunable noise-free notch can be
programmed via 2-Wire control to shape the switching noise and create a narrow frequency band in the AM radio
spectrum in which the PWM common mode switching energy is not allowed to spread. This noise-free notch is
18
Rev. 0.6
Si2704/05/06/07-A10
nominally 20 kHz wide and tunable in 5 kHz increments from 520 to 1710 kHz, virtually equalizing the noise level
across the band. The noise-free notch can be dynamically tuned during normal operation without adversely
affecting the internal audio processing or the differential output signal integrity.
Spread Mode PWM with the tunable noise-free notch is useful for systems in which the Si2705/07 needs to co-exist
with an AM radio receiver. In normal AM radio operation, the system MCU programs the noise-free notch
frequency in the Si2705/07 to the same frequency as the AM radio to inhibit PWM switching noise from interfering
with radio reception. Because Spread Mode PWM is also engaged, switching noise outside of the noise-free notch
band is also suppressed for mitigating broadband EMI radiation
The noise-free notch can be placed at different frequencies by programming property PWM_AM_TUNE_FREQ.
More information on the complete range of programming parameters and settings available for optimized operation
can be found in the “AN469: Si270x Programming Guide”.
Figure 13. PWM CM Spectrum for Spread Mode PWM with Noise-Free Notch
4.2. Operating Modes
The Si2704/05/06/07 features four operating modes: one active mode (Active) and three low power modes
(Standby, Sleep and Power Down). The low power modes differ on power consumption and wake up times,
providing the flexibility to meet system design requirements. See Table 3, “DC Characteristics—Supplies and
Interfaces,” on page 6 for additional information on startup times and power consumption.
Figure 14 illustrates the device state diagram highlighting the key operating modes and the allowed transitions.
For more information concerning operating modes and their programming requirements, refer to “AN469: Si270x
Programming Guide”.
4.2.1. Active Mode
2
Active mode is the normal operational mode in which the chip accepts digital I S data at the input, drives an audio
output and is programmable via a 2-Wire interface bus.
Active Mode is initiated by setting the ACTIVE argument of the ACTIVATE command via the 2-Wire interface. To
avoid clicks and pops in the audio output, mute is de-asserted after entering Active Mode.
Rev. 0.6
19
Si2704/05/06/07-A10
RESET
Assert
RESET
Release
RESET
Power Down
Mode
POWER_DOWN
POWER_UP
POWER_DOWN
POWER_DOWN
Standby
Mode
ACTIVATE
[ ACTIVE / STANDBY / AAD ]
ACTIVATE
[ SLEEP / STANDBY ]
ACTIVATE
[ SLEEP / ACTIVE ]
Sleep
Mode
Active
Mode
Figure 14. Operating Modes
4.2.2. Standby Mode
Standby Mode is a reduced power state where the register states are preserved and the 2-Wire interface is fully
operational, allowing for new parameters and configuration settings to be programmed even though the amplifier
output is powered down. This state has the shortest wake-up time relative to the other low power modes. If the
buffered reference clock output (CLKO) is enabled, the timing generation circuitry remains active.
Standby Mode is initiated by setting the STANDBY argument of the ACTIVATE command via the 2-Wire interface.
Standby Mode can also be initiated by setting the AAD argument of the ACTIVATE command, which additionally
enables the Audio Activity Detector. See "4.5.2. Audio Activity Detector" on page 24 for additional information
about this setting.
To avoid clicks and pops in the audio output, mute is first asserted before entering Standby Mode.
4.2.3. Sleep Mode
Sleep Mode is the lowest power consumption state in which the chip parameters and configurations are retained.
However, chip parameter and configuration settings cannot be programmed and the buffered reference clock
output (CLKO) is disabled in this mode. The time to activate the chip is shorter from the Sleep Mode than when
activating from the Power Down Mode.
Sleep mode is initiated by setting the SLEEP argument of the ACTIVATE command.
4.2.4. Power Down Mode and Reset
Asserting the RST pin low disables the analog and digital circuitry, resets the registers to their default settings, and
disables the 2-Wire bus. The RST pin should always be asserted low when power to the device is ramped up, and
released once the power supply voltages have stabilized.
After RST is released high, the chip comes up in Power Down Mode with the registers set to their default values.
The 2-Wire interface remains active but only responds to the POWER_UP command that puts the device into
20
Rev. 0.6
Si2704/05/06/07-A10
Standby Mode so that the high power outputs are prevented from being enabled prior to the registers being
configured. Any other command sent to the device is acknowledged on the bus but ignored by the device. This
mode has the highest wake-up time and lowest power consumption of the three low power modes.
A POWER_DOWN command causes a transition to Power Down Mode, disabling the outputs and resetting all
parameter registers to default values.
4.3. Chip Configuration
The Si270x can be programmed via the 2-Wire interface for several operating configurations.
4.3.1. Multi-Function Pins (MFPs)
Three multi-function pins (MFPs) support a wide range of system configurations while minimizing pin count. These
MFPs are programmed via the 2-Wire interface. Table 13 outlines all available signals, and Table 14 shows the
signal configuration options available on each MFP with the default in bold.
Table 13. Multi-Function Signal Definitions
Signal Name
Functional Description
Tri-level output mode select
Interrupt flag
OUTSEL
INT
DIN2
2
I S data input 2
2
DIN3
I S data input 3
2
DOUT
GPO1–3
I S data output
General purpose output
The MFPs default to High-Z state. MFP1 can be programmed to be signal INT or GPO1. MFP2 can be
programmed to be signal OUTSEL, DIN2, DOUT2 or GPO2. MFP3 can be programmed to be signal DIN3, DOUT
or GPO3. Table 14 summarizes the MFP configuration options with the default functionality shown in bold.
Table 14. MFP Configuration Options
Pin Name
Pin Number
Signal Options
MFP1
#10 (QFN)
High-Z, INT, GPO1
#13 (eTQFP)
MFP2
MFP3
#11 (QFN)
#14 (eTQFP)
High-Z, OUTSEL, DIN2, DOUT, GPO2
High-Z, DIN3, DOUT, GPO3
#7 (QFN)
#10 (eTQFP)
2
The Si270x can receive digital I S audio signal from up to three different sources with the default configuration
being only one input. For cases where more than one signal input is desired or alternatively a signal output is
desired, the MFPs should be programmed to an appropriate configuration with additional DINx/DOUT signals.
Three general purpose output (GPO) pins are also available. The GPOs can be programmed to output logic 1,
logic 0, or a Hi-Z state. These pins can be used for example to control multiplexer switches in the application via
the 2-Wire bus.
MFP pin function is established using the MFP_PIN_CFG command. Refer to the “AN469: Si270x Programming
Guide” for more information on the options and settings requested for operation of the multi function pins.
Rev. 0.6
21
Si2704/05/06/07-A10
4.3.2. Output Mode Configuration (Si2705/07 only)
The Si2705/07 can be programmed via 2-Wire or configured using the OUTSEL MFP to operate in three different
output modes: 2.1 mode, 2.0 mode and aux out mode, with the 2.0 mode being the default. If OUTSEL is not
configured as OUTSEL, these output modes can instead be programmed by setting the argument
OUTSEL_MODE of the ACTIVATE command. Refer to the “AN469: Si270x Programming Guide” for more
information on the options and settings requested for the different operation modes.
OUTSEL is a three-level input with decoding to configure the analog audio signal output at AUXOL/R pins as
shown in Table 15.
Table 15. OUTSEL MFP Decoding
Description
OUTSEL
Output
Configuration
H-Bridge Amplifier
Aux Channel
Analog Output
(mono aux out)
Main Channel
Analog Output
(stereo aux out)
GND
Aux Out Mode
2.0 Mode
disable
enable
enable
disable
disable
enable
enable
disable
disable
V /2
IO
V
2.1 Mode
IO
For stereo implementations, the 2.0 mode is selected enabling the main channel stereo power stage outputs. This
is the default mode when OUTSEL is not externally driven, or when OUTSEL is driven to mid-level between V
and GND.
IO
In 2.1 mode, with OUTSEL driven high to V , the main channel stereo power stage is enabled to drive stereo
IO
bridge-tied loads while a PWM DAC produces mono analog audio from the auxiliary channel to drive a subwoofer
or central channel analog input amplifier.
To drive an external stereo analog amplifier (e.g., for headphones) the PWM DAC can be configured to output the
main stereo channel. In this case, OUTSEL is driven low to GND.
To avoid unwanted audible pop noises on the output, the Si270x implements circuitry to minimize the output
transients that occur while charging and discharging the PWM DAC ac coupling capacitor (see C10 and C11 in the
typical application schematic on page 13). The click and pop noise reduction circuit controls the charging and
discharging currents on the capacitors to prevent sudden changes in the output bias level and the consequent
glitches in the output voltage.
Left
channel
PWM
Aux
channel
PWM
Right
channel
PWM
OUTSEL
1
2
2
1
MUX
MUX
Left
Right
Stereo PWM DAC
AUXOL
AUXOR
Figure 15. MUX OUTSEL Configuration
OUTSEL can be driven by a headphone plug detection circuit as shown in Figure 16. The ratio between the two
resistors in the diagram configures the outputs for a 2.0 (with R1=R2) or a 2.1 application (with R2>>R1). In this
application example, OUTSEL may be used for enabling and disabling the external amplifiers.
22
Rev. 0.6
Si2704/05/06/07-A10
R1
Audio Left
OUTSEL
Audio Right
R2
Figure 16. Headphone Plug Detection Application Schematic
4.4. Clocking
A low jitter on-chip PLL synchronizes to an external clock reference and generates all necessary internal clocks.
2
Three options are available for the external reference: a crystal, a reference clock or the digital I S audio bit clock.
In addition, a buffered user-programmable output clock can be generated on the CLKO pin for use as a clock
reference for external circuits.
4.4.1. Reference Clock Input
Using an external crystal, the on-chip crystal oscillator generates a precise, low jitter internal clock reference for the
best audio performance.
For system design flexibility, the device also supports the options to use either an external reference clock or the
2
I S bit clock as the PLL reference. Noise performance of the amplifier is a direct function of the jitter characteristics
of the external source.
The source of the external reference is programmed using the CLOCK_SOURCE property through the 2-Wire
interface.
4.4.1.1. Crystal Oscillator Operation
When a crystal is connected between XTLI and XTLO pins and the chip is configured properly all the timing for the
chip is derived from the on-chip crystal oscillator.
A range of crystals are supported and the device needs to be programmed to the selected frequency using the
CLOCK_REF_FREQ property. The crystal oscillator provides the best audio performance.
4.4.1.2. External Reference Clock Operation
In this mode, the device operates in slave clock mode and the reference clock is provided by an external clock
source on pin XTLI. A wide range of input clock frequencies are supported in this mode ranging from 2.048 to
49 MHz. Refer to Table 11 on page 12 or to the “AN469: Si270x Programming Guide” for more information on the
complete range of frequencies and settings required for operation on this mode.
2
4.4.1.3. I S Reference Clock Operation
2
The device can operate in slave clock mode using the DCLK signal from the I S bus as a timing reference. In this
mode the device needs to be programmed for one of the supported I S clock rates and pin XTLI should be
2
connected to ground.
4.4.2. Reference Clock Output
The Si2704/05/06/07 may provide a buffered output clock to be used as reference for external circuits when the
chip is programmed for either Active or Standby mode. The clock output frequency and synchronization source is
programmable.
The Si270x supports a number of reference clock frequencies that are related to the PWM switching rate. These
CLKO output frequencies can be especially useful for synchronizing the amplifier to switching power supplies.
Refer to the “AN469: Si270x Programming Guide” for more information on the settings requested for operation.
Rev. 0.6
23
Si2704/05/06/07-A10
2
4.5. Digital Audio I S Interface
2
2
The Si270x receives digital audio data using its I S interface. I S inputs DIN2 and DIN3 can be configured as either
an input or output while DIN is restricted to input only, and all three can be configured to operate in either master or
slave mode. Only one output is supported at a time. All data ports operate synchronously from a single bit-clock
and frame-clock signal. During normal operation, the crossbar mixer outputs are independently programmed to be
a linear combination of any of the channels from the configured inputs with a scaling range from –1 to +1 for each
channel with 8-bit precision.
4.5.1. Auto-Rate Detection
2
The Si270x features an auto-rate detector. It actively monitors the I S bit and frame clock inputs during operation,
detects rate changes, and makes the necessary adjustments to various clock system parameters to ensure correct
operation of the amplifier.
4.5.2. Audio Activity Detector
The device has an audio activity detector (AAD) that monitors the presence of audio at the input. In normal
operation, if the input audio level falls below a programmable threshold for a programmable period of time, it
causes the device to enter the low power Standby Mode. When the input audio level subsequently increases above
the threshold, the device returns to normal Active Mode.
4.5.3. Digital Audio Output
2
2
The Si270x provides a bypass mode that routes I S audio input directly to the I S output port. The output port in
turn can be connected to an off-chip device such as a DAC, DSP or digital media controller.
4.5.4. Audio data formats
2
The digital audio interface supports 3 different audio data formats: I S, Left-Justified and DSP Mode.
2
In I S mode, the MSB is captured on the second rising edge of DCLK following each DFS transition. The remaining
bits of the word are sent in order, down to the LSB. The left channel is transferred first when the DFS is low, and the
2
right channel is transferred when the DFS is high. Figure 17 shows a diagram for the I S digital audio format.
In Left-Justified mode, the MSB is captured on the first rising edge of DCLK following each DFS transition. The
remaining bits of the word are sent in order, down to the LSB. The left channel is transferred first when the DFS is
high, and the right channel is transferred when the DFS is low. Figure 18 shows a diagram for the Left-Justified
digital audio format.
In DSP mode, the DFS becomes a pulse, one DCLK period wide. The left channel is transferred first, followed
immediately by the right channel. There are two options in transferring the digital audio data in DSP mode: the
MSB of the left channel can be transferred on the first rising edge of DCLK following the DFS pulse or on the
second rising edge. Figure 19 shows a diagram for the DSP digital audio format.
In all audio formats, depending on the word size, DCLK frequency and sample rates, there may be unused DCLK
cycles after the LSB of each word before the next DFS transition and MSB of the next word. In this event, for power
2
saving, in I S slave mode DCLK sent to the Si270x can be programmed to remain low until the next DFS transition
appears.
The device supports both rising edge and falling edge DCLK. The number of audio bits in each audio sample
defaults to 24 bits and can be configured to 16, 20, 24 or 32 bits. The leading edge and the data format are
selected using the DIGITAL_AUDIO_CONFIG property.
2
4.5.5. I S Master Mode
2
In master mode, the Si270x is configured for 32-bit word per audio sample, rising edge DCLK, and I S mode data
format.
24
Rev. 0.6
Si2704/05/06/07-A10
INVERTED
DCLK
(IFALL = 1)
(IFALL = 0)
DCLK
DFS
DIN
LEFT CHANNEL
RIGHT CHANNEL
1 DCLK
I2S 0x00
1 DCLK
n-2
n
n-1
2
1
0
n-1
n-2
n
2
1
0
MSB
LSB
MSB
LSB
Figure 17. I2S Digital Audio Format
INVERTED
DCLK
(IFALL = 1)
(IFALL = 0)
DCLK
DFS
LEFT CHANNEL
RIGHT CHANNEL
2
Left-Justified
0x03
DOUT
n
n-1
n-2
1
0
n
n-1
n-2
2
1
0
MSB
LSB
MSB
LSB
Figure 18. Left-Justified Digital Audio Format
(IFALL = 0)
DCLK
DFS
RIGHT CHANNEL
LEFT CHANNEL
DOUT
DSP 0x06
DSP 0x04
n
n-1
n-2
n-1
2
1
0
n
n-1
n-2
n-1
2
1
0
(MSB at 1st rising edge)
MSB
LSB
MSB
LSB
LEFT CHANNEL
1 DCLK
RIGHT CHANNEL
2
DOUT
n
n-2
2
1
0
n
n-2
1
0
(MSB at 2nd rising edge)
MSB
LSB
MSB
LSB
Figure 19. DSP Digital Audio Format
Rev. 0.6
25
Si2704/05/06/07-A10
4.6. Digital Audio Processing (DAP)
The Si270x implements programmable digital audio processing which features volume control, dynamic range
compressor (DRC), and audio filtering such as tone control, parametric equalization, crossover, and de-emphasis.
The three channel digital audio processing chain for the Si2707 is shown in Figure 20.
I2S
I2S
I2S
Input 1
Input 2
Input 3
Crossbar Mixer
32.0
44.1kHz
48.0
L+R
2
L
R
Asynchronous Sample Rate Converter
Tone1
48.0 kHz
ßL1
ßL2
ßR1
ßR2
ßM1
ßM2
Tone2
7 Bi-Quad Parametric EQ
2 Bi-Quad EQ
Treble/Bass Shelving Filters
De-Emphasis
HP Cross Over Filter
Volume Master
LP X-over
Volume Balance
Volume Aux
Dynamic Range Compression
DC Notch Filter
Limiter
Left
Right
Aux
channel channel
channel
Figure 20. Signal Processing Chain
As outlined in "4.5. Digital Audio I2S Interface " on page 24, the crossbar mixer combines the selected audio
sources and outputs the corresponding Left and Right main channels and an Aux Channel containing any linear
combination of the inputs. The Aux Channel can either be disabled completely, configured as a mono low pass
subwoofer channel, or as a mono full bandwidth center channel according to system requirement.
2
To make all downstream audio processing independent of the input I S clock frequencies, an asynchronous
sample rate converter (ASRC) normalizes the input rate to 48 kHz.
Refer to the “AN469: Si270x Programming Guide” for more information on the complete range of programming
parameters and settings requested for operation of the digital audio processing features.
26
Rev. 0.6
Si2704/05/06/07-A10
4.6.1. Parametric Equalization (Si2706/07 only)
The Si2706/07 includes 16 fully programmable parametric equalizer filters. Seven of these filters are implemented
in each of the Left/Right main channels and the remaining two are used for the Aux Channel. The filters are
implemented using a biquad form and can be programmed to shape the frequency response of each channel
independently. The filters implement the configuration presented on Figure 21 which can be represented by the
following equation:
y[n]=b0x[n]+b1x[n-1]+b2x[n-2]+a1y[n-1]+a2y[n-2];
Where x[n] is the input sample and y[n] is the output sample.
0
-1
-1
-1
-1
1
2
1
2
Figure 21. Biquad Filter Configuration
The five coefficients for each biquad are programmed via the 2-Wire interface by using the command
SET_EQ_BIQUAD_FILTER_COEFF.
4.6.2. Tone Control
The Si270x implements tone control in the form of two second order shelving filters for bass and treble. Each filter
has programmable cut-off frequency and boost/cut gain. Cut-off frequency can be adjusted from 5 to 20 kHz by
setting properties BASS_CORNER_FREQ (for bass) and TREBLE_CORNER_FREQ (for treble). Gain can be
adjusted from –18 to +18 dB in 1 dB steps by setting properties BASS_BOOST_CUT (for bass) and
TREBLE_BOOST_CUT (for treble). Figure 22 shows the characteristics of the bass and treble shelving filters.
Gain
Gain
BASS
TREBLE
Shelving Filter
Shelving Filter
Boost
Cut
Boost
Cut
1
1
Cutoff
Freq
Cutoff
Freq
Frequency
Frequency
Figure 22. Generic Bass/Treble Shelving Filter Characteristics
Rev. 0.6
27
Si2704/05/06/07-A10
4.6.3. De-Emphasis (Si2706/07 only)
The Si2706/07 features a de-emphasis filtering option in order to be able to process recorded audio that for noise
reasons has been subject to 50/15 µs pre-emphasis. The 50/15 µs filter implemented has corner frequencies at
3.183 kHz and 10.610 kHz.
4.6.4. Crossover Filter (Si2706/07 only)
The Si2706/07 features a programmable frequency 12 dB/octave Linkwitz-Riley type crossover filter that provides
separation of the low and high frequency content of the audio signal. The filter high-pass output is used to drive the
Left/Right main channel and the low-pass output feeds the Aux Channel to be used in 2.1 Mode with an external
subwoofer power driver. The cutoff frequency can be programmed from 80 to 320 Hz in 40 Hz steps via the 2-Wire
interface by setting the CROSSOVER_FREQ property. The same property can also be used to disable and bypass
the crossover filter.
4.6.5. Digital Volume Controls
The volume control maintains a master volume for all the channels, including the Left/Right main channels and the
Aux Channel. The channel volume can be set in 0.5 dB gain/attenuation steps ranging from –100 dB (mute level)
to +28 dB using the VOLUME_MASTER property.
To prevent audible artifacts due to volume transitions, the slope of the change in volume can be programmed by
configuring the VOLUME_RAMP property. The default configuration is 0.1 dB/ms (dB per millisecond) and
programming can be done in 0.1 dB/ms steps and ranging from 0.1 to 6.3 dB/ms.
The device also provides balance control between the Left and Right channels through the use of the
VOLUME_BALANCE property. This property specifies the audio gain/attenuation division in terms of percent split
between the two channels.
The Aux Channel volume control specifies the percentage of gain/attenuation levels relative to the master volume
using the VOLUME_AUX_CHANNEL property.
Mute is implemented using the VOLUME_MUTE. Un-muting returns the volume setting to the value stored in the
volume registers at the programmed volume transition slope rate. During the mute condition, the PWM outputs
switch at a 50% duty cycle.
28
Rev. 0.6
Si2704/05/06/07-A10
4.6.6. Dynamic Range Compression (Si2706/07 only)
The Si2706/07 features dynamic range compression (DRC) with programmable linear gain, compression
threshold, compression ratio, look ahead time, attack rate, and release rate.
DRC increases the net output power without clipping by decreasing the peak amplitudes of audio signals and
increasing the rms content of the lower amplitude audio signal. Audio signals below the threshold are increased by
the linear gain and audio signals above the threshold are compressed by a pre-defined compression ratio.
Figure 23 shows a plot of dynamic range compression audio processing with the DRC_THRESHOLD parameter
set at –40 dBFS, DRC_GAIN parameter at +20 dB relative to an uncompressed transfer function and
DRC_SLOPE set for a 2:1 compression ratio. For input signals below the compression threshold of –40 dBFS, the
output signal is increased by 20 dB relative to the input signal. For input signals above the compression threshold
the input signal is increased by 1 dB for every 2 dB increase in audio input level.
Figure 23. Dynamic Range Compression Example
In this example, the input dynamic range of 90 dB is reduced to an output dynamic range of 70 dB.
Figure 24 shows the time domain response of the dynamic range compression. The DRC_ATTACK_TIME
parameter sets how quickly the gain compression responds to changes in the input level, and the
DRC_RELEASE_TIME parameter sets how quickly the gain compression returns to linear gain once the audio
input level drops below the compression threshold.
DRC_LOOKAHEAD_TIME allows setting the look ahead time that permits the DRC circuit to adjust the
compression to sudden level changes thus preventing the clipping of the fast changing signal. Refer to “AN503:
Si270x Class-D Amplifier—Dynamic Range Compressor Use” for additional information.
Rev. 0.6
29
Si2704/05/06/07-A10
Figure 24. Time Domain Characteristics of the Audio Dynamic Range Controller
4.6.7. Hard Signal Limiter
The device implements a hard limiter to avoid exceeding the maximum modulation rate of the amplifier. The hard
limiter is always enabled.
4.6.8. DC Notch Filter
A dc notch filter with a 5 Hz corner frequency is implemented as the final function in the signal processing chain to
remove any dc component from the output signal. Each channel has a separate dc notch filter.
4.6.9. Tone and Alert Generation
The Si270x includes two independent tone generators with programmable frequencies and on/off times.
2
The output of both tone generators is fed to a mixer which combines the tones with the I S inputs. The tones’
amplitudes can be adjusted by programming the mixer coefficients using the SET_AUDIO_INPUT_MIXER
command.
This feature allows customization of audible alarms and alerts. Programmable frequencies range from 100 Hz to
20 kHz in 100 Hz steps and on/off times range from 0 to 65 seconds in 1 ms steps and are set via the 2-Wire
interface using the properties TONE_ONE_FREQ, TONE_ONE_ON_TIME, TONE_ONE_OFF_TIME, and
TONE_ONE_AMPLITUDE
for
the
first
tone
and
TONE_TWO_FREQ,
TONE_TWO_ON_TIME,
TONE_TWO_OFF_TIME, and TONE_TWO_AMPLITUDE for the second tone.
4.7. Fault Detection and Response
To help protect the H-bridge driver and external loads, the output stage has fault detection circuitry that allows the
device to respond to over-current and over-temperature events.
The over-temperature circuitry monitors the temperature of the device and if the temperature exceeds 135 ºC a
thermal error is issued, and the output stage is shut down by transitioning the device to Standby Mode.
The over-current protection circuit constantly monitors the current of the output stage and triggers a fault alarm if
an over-current condition is detected from three different events: a short circuit across the speaker terminals, a
short circuit of any of the outputs to ground and a short circuit of any of the outputs to the supply voltage. In each
case, the detector issues a fault if the 2.5 A current threshold is exceeded. In response to this fault the device
power stage is shut down by transitioning the device to Standby Mode.
30
Rev. 0.6
Si2704/05/06/07-A10
4.8. Power Supply and Grounding Considerations
Careful attention should be given to the power and ground routing to allow for optimal performance of the Si270x.
The low voltage supplies, V and V , should be decoupled with 0.1 µF capacitors soldered as close to the device
DD
IO
as possible so that parasitic inductances are minimized. For the power stage supplies V
and V
, each should
PPR
PPL
be bypassed with a 0.1 µF in ceramic capacitor, located as close to the device as possible, in parallel with a 220 µF
electrolytic capacitor. This allows for optimal filtering in the full frequency spectrum. For detailed information on
board layout considerations and examples refer to “AN470: Si270x Layout Guidelines.”
4.9. Control Interface
2
An I C-compatible 2-Wire serial port slave interface allows an external controller to send commands, configure
properties, and receive responses from the Si270x. Commands may only be sent after V and V supplies are
IO
DD
applied and the RST pin has been released high.
The CLKO pin serves as a configuration boot-strap to select one of two unique addresses to which the Si270x
responds. During reset, if CLKO is pulled low using a 2.2 k resistor connected to ground, then the 7 bit device
address is 1001010 (0x94). If CLKO is left floating, a 22 k internal pull-up within the Si270x causes the 2-Wire to
select a device address of 0011011 (0x36).
A 2-wire transaction begins with the START condition, which occurs when SDIO falls while SCLK is high. Next, the
2-wire master drives an 8-bit control word serially on SDIO which is captured by the device on rising edges of
SCLK. The control word consists of a 7 bit device address followed by a read/write bit (read = 1, write = 0). If the
address matches, the Si270x acknowledges the control word by driving SDIO low on the next falling edge of SCLK.
For write operations, the 2-Wire master sends an eight bit data byte on SDIO following the control word, which is
captured by the device on rising edges of SCLK. The Si270x acknowledges each data byte by driving SDIO low for
one cycle, on the next falling edge of SCLK. The 2-Wire master may write up to eight data bytes during a single
2-wire transaction. The first byte is a command, and the next seven bytes are arguments.
For read operations, after the Si270x has acknowledged the control byte, it drives a data byte on SDIO, changing
the state of SDIO on the falling edge of SCLK. The 2-wire master acknowledges each data byte by driving SDIO
low for one cycle on the next falling edge of SCLK. If a data byte is not acknowledged, the transaction ends. The
2-wire master may read up to 16 data bytes in a single 2-wire transaction. These bytes contain the response data
from the Si270x. A 2-wire transaction ends with the STOP condition, which occurs when SDIO rises while SCLK is
high. For details on timing specifications and diagrams, refer to Table 8 on page 9, Figure 3 on page 11, and
Figure 4 on page 11.
4.10. Programming with Commands
The Si270x provides a simple yet powerful software interface to program configuration and parameter settings. The
device is programmed using commands, arguments, properties, and responses. To perform an action, the user
writes a command byte and associated arguments causing the chip to execute the given command. Commands
control actions, such as powering up the device, shutting down the device, or configure the audio input source.
Arguments are specific to a given command and are used to modify the command. For example, for the
SET_AUDIO_INPUT_MIXER command, arguments are required to set the coefficients of the linear combination of
the sources. Properties are a special command argument used to modify the default chip operation and are
generally configured immediately after power up. Examples of properties include CLOCK_SOURCE and
DEEMPHASIS. A complete list of commands and properties is available in “5. Commands and Properties”.
Responses provide the user information and are returned after a command and associated arguments are sent. At
a minimum, all commands respond with a one-byte status reply indicating interrupt and clear-to-send status
information. Subsequent sections of this data sheet mention many of the commands and properties that are used
to alter different functions. More information on the complete list of programming modes of operation and
properties can be found in the “AN469: Si270x Programming Guide.”
Rev. 0.6
31
Si2704/05/06/07-A10
5. Commands and Properties
Table 16 and Table 17 are the summary of commands and properties for the Si270x Class D Audio Amplifier
device.
Table 16. Class D Audio Amplifier Command Summary
Common Commands
Number
0x01
0x10
0x12
0x13
0x14
0x15
0x16
0x21
0x22
0x23
0x24
0x31
0x32
Name
Summary
POWER_UP
FUNC_INFO
Power-up the device.
Returns the Function revision information of the device.
Set the value of a property.
SET_PROPERTY
GET_PROPERTY
MFP_PIN_CFG
Retrieve a property’s value.
Configure MFP pins.
SET_AUDIO_INPUT_MIXER
OUTSEL
Configure Audio input source.
Select amplifier outputs.
SET_EQ_BIQUAD_FILTER_COEFF Set Biquad Filter.
GET_INT_STATUS
GET_FAULT_STATUS
GET_AUDIO_STATUS
ACTIVATE
Read interrupt status bit.
Get the source of the fault condition.
Read back audio parameters.
Enable or disable audio processing & amplifier output operations.
Power-down the device.
POWER_DOWN
Table 17. Class D Audio Amplifier Property Summary
Category Number
Name
Summary
Configure Interrupt Source.
Interrupt 0x0001 INT_ENABLE
Clock
0x0101 REF_CLOCK_SOURCE
0x0102 REF_CLOCK_FREQ
0x0103 CLOCK_OUT_FREQ
Select the reference source for PLL.
Set the reference clock freq for the PLL in kHz units.
Configure output clock frequency.
I2S
0x0104 DIGITAL_AUDIO_SAMPLE_RATE Set the digital audio sampling rate.
0x0201 DIGITAL_AUDIO_CONFIG
0x0301 AAD_CONFIG
Sets the Digital Audio Input Format Configuration.
AAD
Set Audio Activity Detector (AAD) Configuration.
0x0302 AAD_THRESHOLD
Set audio level threshold where the device will go into
standby if the audio input level falls below this thresh-
old.
0x0303 AAD_DURATION
Set how long the signal has been below the threshold
in ms before going to standby state.
32
Rev. 0.6
Si2704/05/06/07-A10
Table 17. Class D Audio Amplifier Property Summary (Continued)
Category Number
Name
Summary
Biquad
Filter
0x1901 CROSSOVER_FREQ
0x2103 BASS_BOOST_CUT
0x2104 BASS_CORNER_FREQ
0x2105 TREBLE_BOOST_CUT
0x2106 TREBLE_CORNER_FREQ
Set crossover freq between Main Channel and Aux
Channel.
Set bass shelving filter boost/cut for the Left and Right
Channel.
Set bass shelving filter corner freq for the Left and
Right Channel.
Set treble shelving filter boost/cut for the Left and
Right Channel.
Set treble shelving filter corner freq for the Left and
Right Channel.
Volume
0x2201 VOLUME_MUTE
0x2202 VOLUME_MASTER
0x2203 VOLUME_BALANCE
0x2204 VOLUME_AUX_CHANNEL
0x2205 VOLUME_RAMP
0x2301 DRC_CONFIG
Mute speaker output.
Set Master Volume.
Set L and R Volume Balance from 0% to 100%.
Set Aux Channel Volume.
Set volume transition slope.
Configure DRC.
DRC
0x2302 DRC_THRESHOLD
0x2303 DRC_SLOPE
Set DRC threshold.
Set the DRC slope. DRC slope is the inverse of DRC
compression ratio.
0x2304 DRC_GAIN
Set DRC gain.
0x2305 DRC_ATTACK_TIME
0x2306 DRC_RELEASE_TIME
0x2307 DRC_LOOKAHEAD_SAMPLES
0x2701 PWM_CONFIG
Set DRC attack time constant in ms units.
Set DRC release time constant in ms units.
Sets the number of look-ahead samples.
Set PWM Output Mode and Max Modulation Index.
Set PWM Freq in kHz units.
PWM
0x2702 PWM_FREQ
0x2703 PWM_AM_TUNE_FREQ
Set where the currently AM Tune Freq is to put the
notch when EMI mitigation mode is used.
0x2704 PWM_MAX_MODULATION_INDEX Set PWM maximum modulation index.
0x2705 PWM_OUTPUT_SLEW_RATE
Set output stage slew rate.
Program- 0x2901 TONE_ONE_AMPLITUDE
Set programmable tone generator amplitude.
Set programmable tone generator frequency.
Set programmable tone generator ON Time in ms.
Set programmable tone generator OFF Time in ms.
Set programmable tone generator amplitude.
Set programmable tone generator frequency.
Set programmable tone generator ON Time in ms.
Set programmable tone generator OFF Time in ms.
mable
Tone
0x2902 TONE_ONE_FREQ
0x2903 TONE_ONE_ON_TIME
0x2904 TONE_ONE_OFF_TIME
0x2905 TONE_TWO_AMPLITUDE
0x2906 TONE_TWO_FREQ
0x2907 TONE_TWO_ON_TIME
0x2908 TONE_TWO_OFF_TIME
Rev. 0.6
33
Si2704/05/06/07-A10
6. Pin Descriptions
6.1. 24-Pin QFN Package
24
23
22
21 20
19
DCLK
DIN
1
18 OUTPL
17 OUTNL
16 GNDL
15 GNDR
14 OUTNR
13 OUTPR
2
3
4
5
6
VIO
GND PAD
(Back Paddle)
SCLK
SDIO
CLKO
Top Down View
24-Pin QFN Package
7
8
9
10 11
12
Figure 25. Pin Configuration
Table 18. Pin Descriptions
Pin Number
Name
GND
Function
GND PAD
Low voltage ground for VDD. Connect to PCB ground plane.
2
1
2
DCLK
DIN
I S digital I/O data clock.
2
I S digital data input port.
3
VIO
I/O supply voltage.
2
4
SCLK
SDIO
CLKO
MFP3
AUXOL
AUXOR
MFP1
Serial clock input for I C-compliant 2-Wire control interface.
2
5
Serial data input/output for I C-compliant 2-Wire control interface.
6
Buffered reference clock output. Configures 2-Wire address on RST.
Multi-function pin 3.
7
8
PWMDAC left channel analog output on Si2705/07 (Reserved on Si2704/06).
PWMDAC right channel analog output on Si2705/07 (Reserved on Si2704/06).
Multi-function pin 1.
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
OUTSEL/MFP2 Output select three-level control input: 2.0, 2.1 or line out mode.
VPPR
OUTPR
OUTNR
GNDR
GNDL
OUTNL
OUTPL
VPPL
RST
Right channel power stage supply voltage.
Right channel power stage “P” output.
Right channel power stage “N” output.
Right channel power stage ground.
Left channel power stage ground.
Left channel power stage “N” output.
Left channel power stage “P” output.
Left channel power stage supply voltage.
Device reset (active low) input.
XTLO
XTLI
External crystal output.
Reference clock or external crystal input.
VDD
Low voltage supply voltage.
2
DFS
I S digital I/O data frame synch.
34
Rev. 0.6
Si2704/05/06/07-A10
6.2. 48-Pin eTQFP Package
48 47 46 45 44 43 42 41 40 39 38 37
1
2
36
NC
DFS
DCLK
DIN
NC
35
VPPL
3
34
OUTPL
4
33
GND
5
32
VIO
OUTNL
6
31
GND
SCLK
SDIO
CLKO
NC
GNDL
GND PAD
(Back Paddle)
7
30
GNDR
8
29
OUTNR
9
28
GND
10
11
12
27
OUTPR
26
NC
VPPR
Top Down View
48-Pin eTQFP Package
25
NC
NC
13 14 15 16 17 18 19 20 21 22 23 24
Figure 26. Pin Configuration
Table 19. Pin Descriptions
Pin Number
Name
Function
1, 10, 11, 12, 13,
14, 15, 16, 23,
24, 25, 36, 37,
38, 39, 45, 46,
47, 48
NC
No connect. Connect to PCB ground plane.
2
2
DFS
DCLK
DIN
I S digital I/O data frame synch.
2
3
I S digital I/O data clock.
2
4
I S digital data input port.
5
VIO
I/O supply voltage.
6, 20, 28, 33, 43
GND
Ground. Connect to PCB ground plane.
2
7
8
SCLK
SDIO
CLKO
MFP3
AUXOL
Serial clock input for I C-compliant 2-Wire control interface.
2
Serial data input/output for I C-compliant 2-Wire control interface.
9
Buffered reference clock output. Configures 2-Wire address on RST.
Multi-function pin 3.
17
18
PWMDAC left channel analog output on Si2705/07 (Reserved on
Si2704/06).
19
AUXOR
PWMDAC right channel analog output on Si2705/07 (Reserved on
Si2704/06).
21
22
26
27
MFP1
Multi-function pin 1.
OUTSEL/MFP2 Output select three-level control input: 2.0, 2.1 or line out mode.
VPPR
Right channel power stage supply voltage.
Right channel power stage “P” output.
OUTPR
Rev. 0.6
35
Si2704/05/06/07-A10
Table 19. Pin Descriptions (Continued)
Pin Number
Name
Function
Right channel power stage “N” output.
29
OUTNR
30
31
32
34
35
40
41
42
44
GNDR
GNDL
OUTNL
OUTPL
VPPL
RST
Right channel power stage ground.
Left channel power stage ground.
Left channel power stage “N” output.
Left channel power stage “P” output.
Left channel power stage supply voltage.
Device reset (active low) input.
External crystal output.
XTLO
XTLI
Reference clock or external crystal input.
Low voltage supply voltage.
VDD
36
Rev. 0.6
Si2704/05/06/07-A10
7. Ordering Guide
Part Number*
Si2704-A10-GM
Si2704-A10-GQ
Description
Package Type
Operating
Temperature
2.0 EMI Mitigating Class D Power Amplifier
2.0 EMI Mitigating Class D Power Amplifier
4x4 QFN
Pb-Free
–20 to 85 °C
–20 to 85 °C
–20 to 85 °C
–20 to 85 °C
–20 to 85 °C
–20 to 85 °C
–20 to 85 °C
–20 to 85 °C
7x7 eTQFP
Pb-Free
Si2705-A10-GM
Si2705-A10-GQ
Si2706-A10-GM
Si2706-A10-GQ
Si2707-A10-GM
Si2707-A10-GQ
2.1 EMI Mitigating Class D Power Amplifier with
tunable noise notch for AM radio
4x4 QFN
Pb-Free
2.1 EMI Mitigating Class D Power Amplifier with
tunable noise notch for AM radio
7x7 eTQFP
Pb-Free
2.0 EMI Mitigating Class D Power Amplifier with
EQ/DRC
4x4 QFN
Pb-Free
2.0 EMI Mitigating Class D Power Amplifier with
EQ/DRC
7x7 eTQFP
Pb-Free
2.1 EMI Mitigating Class D Power Amplifier with
tunable noise notch for AM radio with EQ/DRC
4x4 QFN
Pb-Free
2.1 EMI Mitigating Class D Power Amplifier with
tunable noise notch for AM radio with EQ/DRC
7x7 eTQFP
Pb-Free
*Note: Add an “R” at the end of the device part number to denote tape and reel option.
Rev. 0.6
37
Si2704/05/06/07-A10
8. Package Outline
8.1. 24-Pin QFN Package
Figure 27 illustrates the package details for 24-pin QFN package option for the Si2704/05/06/07. Table 20 lists the
values for the dimensions shown in the illustration.
Figure 27. 24-Pin QFN
Table 20. 24-Pin QFN Package Dimensions
Dimension
Min
0.80
0.00
0.18
Nom
0.85
Max
0.90
0.05
0.30
Dimension
Min
2.40
0.20
—
Nom
2.50
0.25
—
Max
2.60
0.30
0.10
0.10
0.08
0.10
0.10
A
E2
L
A1
0.02
b
0.25
aaa
bbb
ccc
ddd
eee
D
4.00 BSC
2.50
—
—
D2
2.40
2.60
—
—
e
E
0.50 BSC
4.00 BSC
—
—
—
—
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MO-220, Variation VGGD-8.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
38
Rev. 0.6
Si2704/05/06/07-A10
8.2. 48-Pin eTQFP Package
Figure 28 illustrates the package details for 48-pin eTQFP package option for the Si2704/05/06/07. Table 21 lists
the values for the dimensions shown in the illustration.
Figure 28. 48-Pin eTQFP
Rev. 0.6
39
Si2704/05/06/07-A10
Table 21. 48-Pin eTQFP Package Dimensions
Dimension
Min
—
Nom
—
Max
1.20
0.15
1.05
0.27
0.20
Dimension
Min
Nom
9.00 BSC
7.00 BSC
3.81
Max
A
E
E1
E2
L
A1
0.05
0.95
0.17
0.09
—
A2
1.00
3.71
0.45
—
3.91
0.75
0.20
0.20
0.08
0.08
7°
b
0.22
0.60
c
D
—
aaa
bbb
ccc
ddd
Θ
—
9.00 BSC
7.00 BSC
3.81
—
—
D1
—
—
D2
3.71
3.91
—
—
e
0.50 BSC
0°
3.5°
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1982.
3. This drawing conforms to JEDEC outline MS-026, variation ABC.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
40
Rev. 0.6
Si2704/05/06/07-A10
9. Package Markings (Top Marks)
9.1. Si2707 Top Mark (QFN)
9.2. Top Mark Explanation
Mark Method
YAG Laser
Line 1 Marking
Part Number
04 = Si2704
05 = Si2705
06 = Si2706
07 = Si2707
Firmware Revision
Die Revision
10 = Firmware Revision 1.0
A = Revision A Die
Line 2 Marking
Line 3 Marking
TTTTT = Internal Code
Internal Tracking Code
Pin 1 Identifier
Circle = 0.5 mm Diameter
(Bottom-Left Justified)
YY = Year
WW = Work Week
Assigned by the Assembly House. Corresponds to the year
and work week of the mold date.
Rev. 0.6
41
Si2704/05/06/07-A10
9.3. Si2707 Top Mark (eTQFP)
9.4. Top Mark Explanation
Mark Method
YAG Laser
Line 1 Marking
Part Number
Si2704
Si2705
Si2706
Si2707
Firmware Revision
Die Revision
10 = Firmware Revision 1.0
A = Revision A Die
Line 2 Marking
Line 3 Marking
TTTTT = Internal Code
Internal Tracking Code
Pin 1 Identifier
Circle = 0.5 mm Diameter
(Bottom-Left Justified)
YY = Year
WW = Work Week
Assigned by the Assembly House. Corresponds to the year
and work week of the mold date.
42
Rev. 0.6
Si2704/05/06/07-A10
10. Additional Reference Resources
Si270x Evaluation Board User’s Guide
AN469: 270x Programming Guide
AN470: 270x Layout Guidelines
AN502: Si270x Class-D Amplifier—Analog Source Setup
AN503: Si270x Class-D Amplifier—Dynamic Range Compressor Use
AN504: Si270x Class-D Amplifier—Dynamic Bass Configuration
AN505: Si270x Class-D Amplifier—Measuring Output Power
AN509: Si270x Class-D Amplifier—Ferrite Bead Filter
AN510: Si270x Class-D Amplifier—Calculating Filter Loss
Si270x Customer Support Site:
http://www.silabs.com
This site contains all application notes, evaluation board schematics and layouts, and evaluation software. NDA
is required for access to some of these documents. To request access, send mysilabs user name and request
for access to AudioInfo@silabs.com.
Rev. 0.6
43
Si2704/05/06/07-A10
DOCUMENT CHANGE LIST
Revision 0.4 to Revision 0.5
Updated Table 3 on page 6.
Updated Table 4 on page 7.
Updated Table 5 on page 7.
Updated Table 6 on page 8.
Updated Table 11 on page 12.
Updated "2. Typical Application Schematic" on page
13.
Updated Figure 15 on page 22.
2
Added "4.5.5. I S Master Mode" on page 24.
Added note to "7. Ordering Guide" on page 37.
Added "9. Package Markings (Top Marks)" on page
41.
Added "9.3. Si2707 Top Mark (eTQFP)" on page 42.
Revision 0.5 to Revision 0.6
Updated eTQFP pin assignments on pages 1 and
35.
Updated eTQFP pin descriptions in Table 19 on
page 35.
Updated Table 1 on page 5.
Updated Table 3 on page 6.
Updated Table 4 on page 7.
Updated Table 5 on page 7.
Updated Table 11 on page 12.
Updated "2. Typical Application Schematic" on page
13.
Updated "3. Typical System Configurations" on page
14
Updated Figure 6 on page 14.
Updated Figure 9 on page 15.
Updated "4. Functional Description" on page 16.
Updated "4.4.1.2. External Reference Clock
Operation" on page 23.
Updated "5. Commands and Properties" on page 32.
Updated Table 16 on page 32.
Updated Table 17 on page 32.
Updated "10. Additional Reference Resources" on
page 43.
44
Rev. 0.6
Si2704/05/06/07-A10
NOTES:
Rev. 0.6
45
Si2704/05/06/07-A10
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Tel: 1+(512) 416-8500
Fax: 1+(512) 416-9669
Toll Free: 1+(877) 444-3032
Email: Audioinfo@silabs.com
Internet: www.silabs.com
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from
the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features
or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, rep-
resentation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation conse-
quential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to
support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where per-
sonal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap-
plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
46
Rev. 0.6
相关型号:
©2020 ICPDF网 联系我们和版权申明