Si4731-D60-GM [SILICON]
BROADCAST AM/FM/SW/LW RADIO RECEIVER; 广播的AM / FM / SW / LW无线电接收器
| 型号： | Si4731-D60-GM |
| 厂家： | 
SILICON |
| 描述： | BROADCAST AM/FM/SW/LW RADIO RECEIVER |
| 文件： | 总44页 (文件大小：389K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Si4730/31/34/35-D60
BROADCAST AM/FM/SW/LW RADIO RECEIVER
Features
Worldwide FM band support
(64–108 MHz)
Worldwide AM band support
(520–1710 kHz)
SW band support (Si4734/35)
(2.3–26.1 MHz)
LW band support (Si4734/35)
(153–279 kHz)
Excellent real-world performance
Integrated VCO
Advanced AM/FM seek tuning
Automatic frequency control (AFC)
Automatic gain control (AGC)
Digital FM stereo decoder
Programmable de-emphasis
Advanced Audio Processing
Multiplexed stereo audio AUXIN
ADC with 85 dB dynamic range
Seven selectable AM channel filters
AM/FM/SW/LW digital tuning
EN55020 compliant
No manual alignment necessary
Programmable reference clock
Adjustable soft mute control
RDS/RBDS processor (Si4731/35)
Digital audio out
2-wire and 3-wire control interface
Integrated LDO regulator
Wide range of ferrite loop sticks and
air loop antennas supported
QFN and SSOP packages
RoHS compliant
Ordering Information:
See page 33.
Pin Assignments
Si473x-D60 (QFN)
Applications
20 19 18 17
NC
FMI
1
16
Table and portable radios
Mini/micro systems
CD/DVD and Blu-ray players
Stereo boom boxes
Modules for consumer electronics
Clock radios
Mini HiFi and docking stations
Entertainment systems
2
15 DOUT/[LIN]
14 LOUT/[DFS]
13 ROUT/[DOUT]
12 GND
RFGND
AMI
3
4
5
GND
PAD
RST
6
11 VA
7
8
9
10
Description
Si473x-D60(SSOP)
The Si473x-D60 digital CMOS AM/FM radio receiver IC integrates the complete
tuner function from antenna input to digital audio output and includes a stereo
audio AUXIN ADC input for converting analog audio into standard I2S digital
audio, enabling a cost efficient digital audio platform for consumer electronic
applications with high TDMA noise immunity, superior radio performance, and
high fidelity audio power amplification. When enabling the analog inputs in stereo
AUXIN ADC-mode, the Si473x-D60 supports I2S digital audio output only (no
analog output).
DOUT/[LIN]
DFS/[RIN]
GPO3/[DCLK]
GPO2/[INT]
GPO1
1
2
24
23
22
21
20
19
18
17
16
15
14
13
LOUT/[DFS]
ROUT/[DOUT]
3
DBYP
VA
4
5
VD
NC
RCLK
SDIO
SCLK
SEN
RST
6
NC
7
Functional Block Diagram
FMI
8
RFGND
NC
9
FM / SW
RIN
10
11
12
Si473x-D60
ANT
LIN
NC
GND
GND
RDS
(Si4731/
35)
DOUT
FMI
DIGITAL
AUDIO
AMI
DFS
LNA
AGC
GPO/DCLK
LOW -IF
DSP
Mux
AMI
RFGND
AM / LW
ANT
ADC
ADC
DAC
DAC
ROUT
LOUT
This product, its features, and/or its
architecture is covered by one or more of
the following patents, as well as other
patents, pending and issued, both
foreign and domestic: 7,127,217;
LNA
AGC
Mux
2.7~5.5 V (QFN)
2.0~5.5 V (SSOP)
VA
CONTROL
INTERFACE
LDO
AFC
VD
1.62 - 3.6 V
+
GND
7,272,373;
7,355,476;
7,272,375;
7,426,376;
7,321,324;
7,471,940;
7,339,503; 7,339,504.
Rev. 1.1 11/11
Copyright © 2011 by Silicon Laboratories
Si473x-D60
Si4730/31/34/35-D60
2
Rev. 1.1
Si4730/31/34/35-D60
TABLE OF CONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.1. QFN Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.2. SSOP Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3. Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.1. QFN/SSOP Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4.2. Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.3. FM Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.4. AM Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.5. SW Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.6. LW Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.7. Stereo Audio AUXIN ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.8. Digital Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4.9. Stereo Audio Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.10. Received Signal Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.11. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.12. Stereo DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.13. Soft Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.14. FM Hi-Cut Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
4.15. De-emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.16. RDS/RBDS Processor
(Si4731/35 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.17. Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.18. Seek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.19. Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.20. Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
4.21. GPO Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.22. Firmware Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.23. Reset, Powerup, and Powerdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.24. 2 V Operation (SSOP Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.25. Programming with Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5.1. Si473x-D60-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5.2. Si473x-D60-GU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
6. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.1. Si473x-D60 QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.2. Si473x-D60 SSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
8. PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Rev. 1.1
3
Si4730/31/34/35-D60
8.1. Si473x-D60 QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
8.2. Si473x-D60 SSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
9. Top Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
9.1. Si473x-D60 Top Marking (QFN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
9.2. Top Marking Explanation (QFN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
9.3. Si473x-D60 Top Marking (SSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
9.4. Top Marking Explanation (SSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
10. Additional Reference Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
4
Rev. 1.1
Si4730/31/34/35-D60
1. Electrical Specifications
Table 1. Recommended Operating Conditions1
Parameter
Analog Supply Voltage
Symbol Test Condition
Min
Typ
—
Max
5.5
3.6
—
Unit
V
2
V
2.7
A
Digital and I/O Supply Voltage
V
1.62
10
—
V
D
Power Supply Powerup Rise Time
Interface Power Supply Powerup Rise Time
V
—
µs
µs
C
DDRISE
V
10
—
—
IORISE
Ambient Temperature
T
–20
25
85
A
Notes:
1. All minimum and maximum specifications apply across the recommended operating conditions. Typical values apply at
VA = 3.3 V and 25 C unless otherwise stated.
2. SSOP devices operate down to 2 V at 25 °C. See section “4.24. 2 V Operation (SSOP Only)” for details.
Rev. 1.1
5
Si4730/31/34/35-D60
Table 2. DC Characteristics
(VA = 2.7 to 5.5 V, VD = 1.62 to 3.6 V, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
FM Mode
V
Supply Current
Supply Current
I
—
—
—
—
—
—
—
8.2
10.5
18.5
0.15
9.1
9.5
13.5
21.5
0.6
AQFN
FMVA
V
I
DQFN
FMVD
1
Digital Output Mode
V
Supply Current
Supply Current
I
ASSOP
FMVA
V
I
DSSOP
FMVD
mA
V
Supply Current
Supply Current
I
10.3
12.8
21.3
0.6
AQFN
FMVA
V
I
9.9
DQFN
FMVD
2
Analog Output Mode
V
Supply Current
Supply Current
I
19.1
0.1
ASSOP
FMVA
V
I
DSSOP
FMVD
AM Mode
V
Supply Current
Supply Current
I
—
—
—
—
—
—
—
—
6.5
8.5
7.5
11.0
16.5
0.50
8.5
AQFN
AMVA
V
I
DQFN
AMVD
Digital Output Mode
Analog Output Mode
V
Supply Current
Supply Current
I
14.5
0.15
7.5
8
ASSOP
AMVA
V
I
DSSOP
AMVD
mA
V
Supply Current
Supply Current
I
AQFN
AMVA
V
I
10.2
17.2
0.4
DQFN
AMVD
V
Supply Current
Supply Current
I
15.3
0.1
ASSOP
AMVA
V
I
DSSOP
AMVD
AUXIN Mode
V
Supply Current
Supply Current
I
—
—
—
—
5.7
6.5
6.3
8.0
AQFN
AUXVA
I
AUXVD
V
DQFN
mA
V
Supply Current
Supply Current
I
0.3
0.4
ASSOP
AUXVA
AUXVD
V
I
11.8
13.0
DSSOP
Powerdown
Powerdown Current
V
—
—
4
9.5
3
15
15
10
10
AQFN
I
µA
µA
APD
V
Powerdown Current
ASSOP
V
V
Powerdown Current
SCLK, RCLK inactive
SCLK, RCLK inactive
—
DQFN
I
DPD
Powerdown Current
—
3
DSSOP
3
High Level Input Voltage
V
0.7 x V
–0.3
–10
—
—
—
V + 0.3
V
V
IH
D
D
3
Low Level Input Voltage
High Level Input Current
Notes:
V
0.3 x V
10
IL
D
3
I
V
= V = 3.6 V
µA
IH
IN
D
1. Guaranteed by characterization.
2. Backwards compatible mode to rev B and rev C. Additional features on this device may increase typical supply current.
3. For input pins SCLK, SEN, SDIO, RST, RCLK, DCLK, DFS, GPO1, GPO2, and GPO3.
4. For output pins SDIO, DOUT, GPO1, GPO2, and GPO3.
6
Rev. 1.1
Si4730/31/34/35-D60
Table 2. DC Characteristics (Continued)
(VA = 2.7 to 5.5 V, VD = 1.62 to 3.6 V, TA = –20 to 85 °C)
Parameter
Symbol
Test Condition
= 0 V,
Min
Typ
Max
Unit
3
Low Level Input Current
I
V
–10
—
10
µA
IL
IN
V = 3.6 V
D
4
High Level Output Voltage
V
I
= 500 µA
0.8 x V
—
—
—
—
V
V
OH
OUT
D
4
Low Level Output Voltage
V
I
= –500 µA
0.2 x V
D
OL
OUT
Notes:
1. Guaranteed by characterization.
2. Backwards compatible mode to rev B and rev C. Additional features on this device may increase typical supply current.
3. For input pins SCLK, SEN, SDIO, RST, RCLK, DCLK, DFS, GPO1, GPO2, and GPO3.
4. For output pins SDIO, DOUT, GPO1, GPO2, and GPO3.
Rev. 1.1
7
Si4730/31/34/35-D60
Table 3. Reset Timing Characteristics1,2,3
(VA = 2.7 to 5.5 V, VD = 1.62 to 3.6 V, TA = –20 to 85 °C)
Parameter
Symbol
Min
100
30
Typ
—
Max
—
Unit
µs
RST Pulse Width and GPO1, GPO2/INT Setup to RST
GPO1, GPO2/INT Hold from RST
Important Notes:
t
SRST
t
—
—
ns
HRST
1. When selecting 2-wire mode, the user must ensure that a 2-wire start condition (falling edge of SDIO while SCLK is
high) does not occur within 300 ns before the rising edge of RST.
2. When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until
after the first start condition.
3. When selecting 3-wire mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the
rising edge of RST.
4. If GPO1 and GPO2 are actively driven by the user, then minimum tSRST is only 30 ns. If GPO1 or GPO2 is hi-Z, then
minimum tSRST is 100 µs, to provide time for on-chip 1 M devices (active while RST is low) to pull GPO1 high and
GPO2 low.
tHRST
tSRST
70%
30%
RST
70%
30%
GPO1
70%
30%
GPO2/
INT
Figure 1. Reset Timing Parameters for Busmode Select
8
Rev. 1.1
Si4730/31/34/35-D60
Table 4. 2-Wire Control Interface Characteristics1,2,3
(VA = 2.7 to 5.5 V, VD = 1.62 to 3.6 V, TA = –20 to 85 °C)
Parameter
Symbol Test Condition
Min
0
Typ
—
Max
400
—
Unit
kHz
µs
SCLK Frequency
SCLK Low Time
SCLK High Time
f
SCL
t
1.3
0.6
0.6
—
LOW
t
—
—
µs
HIGH
SCLK Input to SDIO Setup
t
t
—
—
µs
SU:STA
(START)
SCLK Input to SDIO Hold
0.6
—
—
µs
HD:STA
(START)
SDIO Input to SCLK Setup
t
t
100
0
—
—
—
—
900
—
ns
ns
µs
SU:DAT
4,5
SDIO Input to SCLK Hold
HD:DAT
SU:STO
SCLK input to SDIO Setup
t
0.6
(STOP)
STOP to START Time
SDIO Output Fall Time
t
1.3
—
—
—
µs
ns
BUF
t
250
f:OUT
Cb
----------
1pF
20 + 0.1
SDIO Input, SCLK Rise/Fall Time
t
t
—
300
ns
f:IN
r:IN
Cb
----------
1pF
20 + 0.1
SCLK, SDIO Capacitive Loading
Input Filter Pulse Suppression
Notes:
C
—
—
—
—
50
50
pF
ns
b
t
SP
1. When VD = 0 V, SCLK and SDIO are low impedance.
2. When selecting 2-wire mode, the user must ensure that a 2-wire start condition (falling edge of SDIO while SCLK is
high) does not occur within 300 ns before the rising edge of RST.
3. When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high
until after the first start condition.
4. The Si473x-D60 delays SDIO by a minimum of 300 ns from the VIH threshold of SCLK to comply with the minimum
tHD:DAT specification.
5. The maximum tHD:DAT has only to be met when fSCL = 400 kHz. At frequencies below 400 KHz, tHD:DAT may be
violated as long as all other timing parameters are met.
Rev. 1.1
9
Si4730/31/34/35-D60
tSU:STA tHD:STA
tLOW
tHIGH
tr:IN
tf:IN
tSP
tSU:STO
tBUF
70%
30%
SCLK
SDIO
70%
30%
tf:IN,
tf:OUT
START
tHD:DAT tSU:DAT
tr:IN
STOP
START
Figure 2. 2-Wire Control Interface Read and Write Timing Parameters
SCLK
A6-A0,
R/W
D7-D0
D7-D0
SDIO
START
ADDRESS + R/W
ACK
DATA
ACK
DATA
ACK
STOP
Figure 3. 2-Wire Control Interface Read and Write Timing Diagram
10
Rev. 1.1
Si4730/31/34/35-D60
Table 5. 3-Wire Control Interface Characteristics
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, TA = –20 to 85 °C)
A
D
Parameter
Symbol
Test Condition
Min
0
Typ
—
—
—
—
—
—
—
—
—
Max
2.5
—
Unit
MHz
ns
SCLK Frequency
SCLK High Time
SCLK Low Time
f
CLK
t
25
25
20
10
10
2
HIGH
t
—
ns
LOW
SDIO Input, SEN to SCLKSetup
SDIO Input to SCLKHold
t
—
ns
S
t
—
ns
HSDIO
SEN Input to SCLKHold
t
—
ns
HSEN
SCLKto SDIO Output Valid
SCLKto SDIO Output High Z
SCLK, SEN, SDIO, Rise/Fall time
t
Read
Read
25
25
10
ns
CDV
t
2
ns
CDZ
t , t
—
ns
R
F
Note: When selecting 3-wire mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the
rising edge of RST.
70%
SCLK
30%
tR
tF
tHSDIO
tHIGH
tLOW
tHSEN
tS
70%
30%
tS
SEN
A6-A5,
R/W,
A4-A1
70%
30%
A7
A0
D15
D14-D1
D0
SDIO
Address In
Data In
Figure 4. 3-Wire Control Interface Write Timing Parameters
70%
30%
SCLK
SEN
tHSDIO
tCDV
tHSEN
tS
tCDZ
70%
30%
tS
70%
30%
A6-A5,
R/W,
A4-A1
A7
A0
D15
D14-D1
D0
SDIO
½ Cycle Bus
Turnaround
Address In
Data Out
Figure 5. 3-Wire Control Interface Read Timing Parameters
Rev. 1.1
11
Si4730/31/34/35-D60
Table 6. Digital Audio Interface Characteristics
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, TA = –20 to 85 °C)
A
D
Parameter
Symbol Test Condition
Min
26
10
10
5
Typ
—
Max
1000
—
Unit
ns
DCLK Cycle Time
t
DCT
DCH
DCLK Pulse Width High
t
—
ns
DCLK Pulse Width Low
t
—
—
ns
DCL
DFS Set-up Time to DCLK Rising Edge
DFS Hold Time from DCLK Rising Edge
t
—
—
ns
SU:DFS
HD:DFS
t
5
—
—
ns
DOUT Propagation Delay from DCLK Falling
Edge
t
0
—
50
ns
PD:DOUT
tDCH
tDCL
DCLK
tDCT
DFS
tHD:DFS
tSU:DFS
DOUT
tPD:OUT
Figure 6. Digital Audio Interface Timing Parameters, I2S Mode
12
Rev. 1.1
Si4730/31/34/35-D60
Table 7. FM Receiver Characteristics1,2
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, TA = –20 to 85 °C)
A
D
Parameter
Symbol
Test Condition
Min
76
—
Typ
—
Max
108
3.5
—
Unit
MHz
Input Frequency
f
RF
3,4,5,6
Sensitivity
(S+N)/N = 26 dB
2.2
10
µV EMF
µV EMF
6,7
RDS Sensitivity
f = 2 kHz,
—
RDS BLER < 5%
7,8
7,8
LNA Input Resistance
3
4
4
5
5
6
k
LNA Input Capacitance
pF
7,9
Input IP3
100
40
35
60
35
72
—
—
15
35
55
—
—
70
45
—
—
105
50
50
70
—
—
—
—
—
—
90
1
dBµV EMF
3,4,7,8
m = 0.3
±200 kHz
±400 kHz
In-band
dB
dB
dB
dB
AM Suppression
Adjacent Channel Selectivity
Alternate Channel Selectivity
Spurious Response Rejection
7
3,4,8
80
—
mV
Audio Output Voltage
RMS
3,8,10
7
dB
Hz
Audio Output L/R Imbalance
–3 dB
–3 dB
—
30
—
—
—
—
0.5
80
54
—
—
Audio Frequency Response Low
Audio Frequency Response High
7
—
kHz
dB
8,10
42
63
58
0.1
75
50
34
30
Audio Stereo Separation
3,4,5,8
dB
Audio Mono S/N
4,5,7,8
dB
Audio Stereo S/N
3,8,10
%
Audio THD
7
De-emphasis Time Constant
FM_DEEMPHASIS = 2
FM_DEEMPHASIS = 1
f = ±400 kHz
µs
µs
3,4,5,6,7,11, 12
Blocking Sensitivity
dBµV
dBµV
f = ±4 MHz
Notes:
1. Additional testing information is available in “AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure.”
Volume = maximum for all tests. Tested at RF = 98.1 MHz.
2. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic,
Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers.
3. F
= 1 kHz, 75 µs de-emphasis, MONO = enabled, and L = R unless noted otherwise.
MOD
4. f = 22.5 kHz.
5. B = 300 Hz to 15 kHz, A-weighted.
AF
6. Analog audio output mode.
7. Guaranteed by characterization.
8. V
= 1 mV.
EMF
9. |f – f | > 2 MHz, f = 2 x f – f . AGC is disabled.
2
1
0
1
2
10. f = 75 kHz.
11. Sensitivity measured at (S+N)/N = 26 dB.
12. Blocker Amplitude = 100 dBuV.
13. At temperature (25 °C).
14. At LOUT and ROUT pins.
Rev. 1.1
13
Si4730/31/34/35-D60
Table 7. FM Receiver Characteristics1,2 (Continued)
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, TA = –20 to 85 °C)
A
D
Parameter
Symbol
Test Condition
f = ±400 kHz, ±800 kHz
f = ±4 MHz, ±8 MHz
Single-ended
Min
—
Typ
40
Max
—
Unit
dBµV
dBµV
k
3,4,5,6,7,11,12
Intermod Sensitivity
—
35
—
7,11,14
R
10
—
—
Audio Output Load Resistance
L
Audio Output Load
C
Single-ended
—
—
—
—
50
60
pF
L
7,11,14
Capacitance
7
Seek/Tune Time
RCLK tolerance
= 100 ppm
ms/channel
7
Powerup Time
From powerdown
—
—
—
110
3
ms
dB
12,13
RSSI Offset
Input levels of 8 and
60 dBµV at RF Input
–3
Notes:
1. Additional testing information is available in “AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure.”
Volume = maximum for all tests. Tested at RF = 98.1 MHz.
2. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic,
Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers.
3. F
= 1 kHz, 75 µs de-emphasis, MONO = enabled, and L = R unless noted otherwise.
MOD
4. f = 22.5 kHz.
5. B = 300 Hz to 15 kHz, A-weighted.
AF
6. Analog audio output mode.
7. Guaranteed by characterization.
8. V
= 1 mV.
EMF
9. |f – f | > 2 MHz, f = 2 x f – f . AGC is disabled.
2
1
0
1
2
10. f = 75 kHz.
11. Sensitivity measured at (S+N)/N = 26 dB.
12. Blocker Amplitude = 100 dBuV.
13. At temperature (25 °C).
14. At LOUT and ROUT pins.
14
Rev. 1.1
Si4730/31/34/35-D60
Table 8. 64–75.9 MHz Input Frequency FM Receiver Characteristics1,2,3
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, TA = –20 to 85 °C)
A
D
Parameter
Symbol
Test Condition
Min
64
—
3
Typ
—
Max
75.9
—
5
Unit
MHz
µV EMF
k
Input Frequency
f
RF
,
4,5,6 8
Sensitivity
LNA Input Resistance
(S+N)/N = 26 dB
3.5
4
3,7
3,7
LNA Input Capacitance
4
5
6
pF
9
Input IP3
—
—
—
—
72
—
—
15
—
—
70
45
10
—
—
105
50
50
70
80
—
—
—
—
—
90
1
dBµV EMF
dB
3,4,5,7
m = 0.3
±200 kHz
±400 kHz
AM Suppression
dB
Adjacent Channel Selectivity
Alternate Channel Selectivity
dB
4,5,7
mV
Audio Output Voltage
RMS
4,7,10
dB
Audio Output L/R Imbalance
3
–3 dB
–3 dB
—
30
—
—
—
80
54
—
50
60
Hz
Audio Frequency Response Low
3
—
kHz
Audio Frequency Response High
4,3,5,7,11
63
0.1
75
50
—
dB
Audio Mono S/N
4,7,10
%
Audio THD
De-emphasis Time Constant
FM_DEEMPHASIS = 2
FM_DEEMPHASIS = 1
Single-ended
µs
µs
k
3,11
R
Audio Output Load Resistance
L
L
3,11
C
Single-ended
—
pF
Audio Output Load Capacitance
3
Seek/Tune Time
RCLK tolerance
= 100 ppm
—
ms/channel
3
Powerup Time
From powerdown
—
—
—
110
3
ms
dB
12
RSSI Offset
Input levels of 8 and
60 dBµV EMF
–3
Notes:
1. Additional testing information is available in “AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure.”
Volume = maximum for all tests. Tested at RF = 98.1 MHz.
2. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic,
Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers.
3. Guaranteed by characterization.
4. F
= 1 kHz, 75 µs de-emphasis, MONO = enabled, and L = R unless noted otherwise.
MOD
5. f = 22.5 kHz.
6. B = 300 Hz to 15 kHz, A-weighted.
AF
7. V
= 1 mV.
EMF
8. Analog output mode.
9. |f – f | > 2 MHz, f = 2 x f – f . AGC is disabled.
2
1
0
1
2
10. f = 75 kHz.
11. At LOUT and ROUT pins.
12. At temperature (25 °C).
Rev. 1.1
15
Si4730/31/34/35-D60
Table 9. AM/SW/LW Receiver Characteristics1,2
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, T = –20 to 85 °C)
A
A
A
Parameter
Symbol
Test Condition
Long Wave (LW)
Medium Wave (AM)
Short Wave (SW)
(S+N)/N = 26 dB
THD < 8%
Min
153
520
2.3
—
Typ
—
Max
279
1710
26.1
35
Unit
kHz
Input Frequency
f
RF
—
kHz
—
MHz
3,4,5
Sensitivity
25
µV EMF
5,6
Large Signal Voltage Handling
—
300
40
—
mV
RMS
RMS
5
Power Supply Rejection Ratio
∆V = 100 mVRMS, 100 Hz
—
—
dB
DD
3,7
Audio Output Voltage
54
60
67
mV
3,4,7
Audio S/N
—
60
—
dB
3,7
Audio THD
—
0.1
2800
—
0.5
—
%
5,8
Antenna Inductance
Long Wave (LW)
Medium Wave (AM)
From powerdown
—
µH
µH
ms
180
—
450
110
5
Powerup Time
—
Notes:
1. Additional testing information is available in “AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure.”
Volume = maximum for all tests. Tested at RF = 520 kHz.
2. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic,
Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers.
3. FMOD = 1 kHz, 30% modulation, 2 kHz channel filter.
4. B = 300 Hz to 15 kHz, A-weighted.
AF
5. Guaranteed by characterization.
6. See “AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure” for evaluation method.
7. V = 5 mVrms.
IN
8. Stray capacitance on antenna and board must be < 10 pF to achieve full tuning range at higher inductance levels.
16
Rev. 1.1
Si4730/31/34/35-D60
Table 10. AC Receiver Characteristics—AUXIN Analog to Digital Converter
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, T = –20 to 85 °C)
A
D
A
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Total Harmonic Distortion +
Noise
THD+N
f = 1 kHz;
measured 20 Hz—20 kHz
—
0.035
0.06
%
Dynamic Range/Signal to Noise
Ratio
SNR
f = 1 kHz at –60 dBFS
A-weighted
—
—
—
85
78
90
—
—
—
dB
dB
dB
f = 1 kHz at –60 dBFS
non-weighted
Crosstalk
f = 1 kHz with 3% Bandpass
filter
Gain Mismatch
Gain Drift
—
—
—
—
—
—
0.03
100
48
—
—
—
1.8
—
—
dB
PPM/°C
kHz
Input Sample Rate
Input Voltage
F
S
V
—
V
pkpk
AI
Input Resistance
Input Capacitance
R
LIATTEN[1:0]
60
k
AI
AI
C
10
pF
Table 11. Digital Filter Characteristics—AUXIN Analog to Digital Converter
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, T = –20 to 85 °C)
A
D
A
Parameter
Symbol
Test Condition
–0.1 dB
Min
0.02
–0.1
25
Typ
—
Max
20
Unit
kHz
dB
Passband Frequency Response
Passband Ripple
20—20 kHz
—
0.1
—
Stopband Corner Frequency
Stopband Attenuation
—
kHz
dB
70
—
—
Rev. 1.1
17
Si4730/31/34/35-D60
Table 12. Reference Clock and Crystal Characteristics
(V = 2.7 to 5.5 V, V = 1.62 to 3.6 V, TA = –20 to 85 °C)
A
D
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Reference Clock
1
RCLK Supported Frequencies
31.130
–100
1
32.768
—
40,000
100
kHz
2
RCLK Frequency Tolerance
ppm
REFCLK_PRESCALE
REFCLK
—
4095
31.130
32.768
34.406
kHz
Crystal Oscillator
Crystal Oscillator Frequency
—
–100
—
32.768
—
—
100
3.5
50
kHz
ppm
pF
2
Crystal Frequency Tolerance
Board Capacitance
ESR
—
—
—
pF
3
CL
7
12
22
3
CL–single ended
14
24
44
pF
Notes:
1. The Si473x-D60 divides the RCLK input by REFCLK_PRESCALE to obtain REFCLK. There are some RCLK
frequencies between 31.130 kHz and 40 MHz that are not supported. For more details, see Table 6 of “AN332: Si47xx
Programming Guide”.
2. A frequency tolerance of ±50 ppm is required for FM seek/tune using 50 kHz channel spacing and AM seek/tune in SW
frequencies.
3. Guaranteed by characterization.
Table 13. Thermal Conditions
Parameter
Thermal Resistance*
Ambient Temperature
Junction Temperature
Symbol
Min
—
Typ
80
Max
—
Unit
°C/W
°C
JA
T
–15
—
25
85
A
T
—
92
°C
J
*Note: Thermal resistance assumes a multi-layer PCB with the exposed pad soldered to a topside PCB pad.
18
Rev. 1.1
Si4730/31/34/35-D60
Table 14. Absolute Maximum Ratings1,2
Parameter
Analog Supply Voltage
Symbol
Value
–0.5 to 5.8
–0.5 to 3.9
10
Unit
V
V
A
Digital and I/O Supply Voltage
V
V
D
3
Input Current
I
mA
V
IN
3
Input Voltage
V
T
–0.3 to (V + 0.3)
IN
IO
Operating Temperature
–40 to 95
–55 to 150
0.4
C
C
OP
Storage Temperature
T
STG
4
RF Input Level
V
pk
Notes:
1. Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation
should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure beyond
recommended operating conditions for extended periods may affect device reliability.
2. The Si473x-D60 devices are high-performance RF integrated circuits with certain pins having an ESD rating of < 2 kV
HBM. Handling and assembly of these devices should only be done at ESD-protected workstations.
3. For input pins DFS, SCLK, SEN, SDIO, RST, RCLK, GPO1, GPO2, GPO3, and DCLK.
4. At RF input pins FMI and AMI.
Rev. 1.1
19
Si4730/31/34/35-D60
2. Typical Application Schematic
2.1. QFN Typical Application Schematic
Optional: Digital Audio Out
OPMODE: 0xB0, 0xB5
16
15
C7
C8
DFS
RIN
LIN
DOUT
R3
R2
R1
17
14
13
GP03/DCLK
LOUT
ROUT
DCLK
DFS
C9
GPO1
GPO2/INT
DOUT
R3
R2
R1
GPO3/DCLK
DFS
Si473x
C9
Optional: AUXIN/Digital Audio Out
OPMODE: 0x5B, 0x0B
DOUT
1
2
3
4
5
15
NC
DOUT
C2
14
FM Antenna
FMI
LOUT
LOUT
13
RFGND
AMI
ROUT
ROUT
Si473x
12
L1
GND
D60
2.7 to 5.5 V
C1
C3
11
RSTB
VA
VA
1.62 to 3.6 V
C4
VD
RSTB
RCLK
SDIO
SCLK
SENB
Optional: AM Air Loop Antenna
L2
GPO3
RCLK
T1
C3
1
3
X1
AMI
C6
C5
RFGND
Optional: For Crystal OSC
Notes:
1. Place C1 close to VA pin and C4 close to VD pin.
2. All grounds connect directly to GND plane on PCB.
3. Pins 1 and 20 are no connects, leave floating.
4. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic,
Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers.
5. Pin 2 connects to the FM antenna interface, and pin 4 connects to the AM antenna interface.
6. Place Si473x-D60 as close as possible to antenna and keep the FMI and AMI traces as short as possible.
20
Rev. 1.1
Si4730/31/34/35-D60
2.2. SSOP Typical Application Schematic
2
1
C7
C8
DFS
RIN
LIN
DOUT
R3
R2
R1
3
GP03/DCLK
LOUT
ROUT
DCLK
DFS
24
23
DOUT
Optional: Digital Audio Out
OPMODE: 0xB0, 0xB5
Si473x
C9
Optional: AUXIN/Digital Audio Out
OPMODE: 0x5B, 0x0B
C9
R1
R2
R3
1
24
DOUT
LOUT
DOUT
DFS
LOUT
ROUT
2
23
DFS
ROUT
3
22
GPO3/DCLK
GPO2/INT
DBYP
GPO3/DCLK
GPO2/INT
GPO1
C1
4
21
VA
2.0 to 5.5 V
VA
1.62 to 3.6 V
C4
5
20
19
18
17
16
15
14
13
GPO1
NC
VD
RCLK
SDIO
SCLK
SENB
VD
6
RCLK
SDIO
SCLK
SENB
RSTB
7
NC
C2
C3
8
FM Antenna
FMI
9
RFGND
NC
10
11
12
RSTB
GND
L1
NC
GND
AMI
Optional: AM Air Loop Antenna
L2
GPO3
RCLK
T1
C3
1
3
X1
AMI
C6
C5
RFGND
Optional: For Crystal OSC
Notes:
1. Place C1 close to VA and C4 close to VD pin.
2. All grounds connect directly to GND plane on PCB.
3. Pins 6 and 7 are no connects, leave floating.
4. Pins 10 and 11 are unused. Tie these pins to GND.
5. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Si47xx Antenna, Schematic,
Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified customers.
6. Pin 8 connects to the FM antenna interface, and pin 12 connects to the AM antenna interface.
7. Place Si473x-D60 as close as possible to antenna and keep the FMI and AMI traces as short as possible.
Rev. 1.1
21
Si4730/31/34/35-D60
3. Bill of Materials
3.1. QFN/SSOP Bill of Materials
Table 15. Si473x-D60 QFN/SSOP Bill of Materials
Component(s)
Value/Description
Supply bypass capacitor, 22 nF, ±20%, Z5U/X7R
Coupling capacitor, 1 nF, ±20%, Z5U/X7R
Coupling capacitor, 0.47 μF, ±20%, Z5U/X7R
Supply bypass capacitor, 100 nF, 10%, Z5U/X7R
Ferrite loop stick, 180–450 μH
Supplier
Murata
C1
C2
C3
C4
L1
Murata
Murata
Murata
Jiaxin
U1
Si47xx AM/FM Radio Tuner
Silicon Laboratories
Optional Components
C5, C6
C7
Crystal load capacitors, 22 pF, ±5%, COG
(Optional for crystal oscillator)
Venkel
Murata
Coupling capacitor, 0.39 μF, ±20%, Z5U/X7R
(Optional for AUXIN)
C8
Coupling capacitor, 0.39 μF, ±20%, Z5U/X7R
Murata
(Optional for AUXIN)
C9
Noise mitigating capacitor, 2~5 pF
(Optional for digital audio)
Murata
R1
Resistor, 600 Ω
Venkel
(Optional for digital audio)
R2
Resistor, 2 kΩ
Venkel
(Optional for digital audio)
R3
Resistor, 2 kΩ
Venkel
(Optional for digital audio)
L2
Air Loop, 10-20 µH
Jiaxin
(Optional for AM Input)
T1
Transformer, 1:5 turns ratio
(Optional for AM Input)
Jiaxin, UMEC
Epson
X1
32.768 kHz crystal
(Optional for crystal oscillator)
22
Rev. 1.1
Si4730/31/34/35-D60
4. Functional Description
4.1. Overview
FM / SW
RIN
Si473x-D60
ANT
LIN
RDS
(Si4731/
35)
DOUT
FMI
DIGITAL
AUDIO
DFS
LNA
GPO/DCLK
LOW-IF
DSP
AGC
Mux
AMI
RFGND
ADC
ADC
DAC
DAC
AM / LW
ANT
ROUT
LOUT
LNA
AGC
Mux
2.7~5.5 V
VA
CONTROL
INTERFACE
LDO
AFC
VD
1.62~3.6 V
GND
Figure 7. Functional Block Diagram
The Si473x-D60 CMOS AM/FM radio receiver IC audio processing.
integrates the complete tuner function from antenna
In addition, the Si473x-D60 provides analog and digital
audio outputs and a programmable reference clock. The
device supports I C-compatible 2-wire control interface,
and a Si4700/01 backwards-compatible 3-wire control
interface.
input to audio output, including a stereo audio AUXIN
ADC input for converting analog audio to digital signals.
This feature enables a cost-efficient digital audio
platform for consumer electronics applications with high
cell phone noise immunity, superior radio performance,
and high fidelity audio power amplification. Offering
unmatched integration and PCB space savings, the
Si473x-D60 requires only a few external components
2
The Si473x-D60 utilizes digital signal processing to
achieve high fidelity, optimal performance, and design
flexibility. The chip provides excellent pilot rejection,
selectivity, and unmatched audio performance, and
offers both the manufacturer and the end-user
2
and less than 15 mm of board area, excluding the
antenna inputs. The Si473x-D60 AM/FM radio provides
the space savings and low power consumption
necessary for portable devices while delivering the high
performance and design simplicity desired for all
AM/FM solutions.
extensive programmability and
experience.
a better listening
The Si4731/35 incorporates a digital signal processor
for the European Radio Data System (RDS) and the
North American Radio Broadcast Data System (RBDS)
including all required symbol decoding, block
synchronization, error detection, and error correction
functions. Using this feature, the Si4731/35 enables
broadcast data such as station identification and song
name to be displayed to the user.
Leveraging Silicon Laboratories' proven and patented
Si4700/01 FM tuner's digital low intermediate frequency
(low-IF) receiver architecture, the Si473x-D60 delivers
superior RF performance and interference rejection in
the AM, FM, SW, and LW bands. The high level of
integration and complete system production test
simplifies design-in, increases system quality, and
improves reliability and manufacturability.
The Si473x-D60 is a feature-rich solution that includes
advanced seek algorithms, soft mute, auto-calibrated
digital tuning, FM stereo processing and advanced
Rev. 1.1
23
Si4730/31/34/35-D60
optimize sensitivity and rejection of strong interferers
allowing better reception of weak stations.
4.2. Operating Modes
The Si473x-D60 operates in either an FM receive, AM
receive, or audio AUXIN ADC mode. In FM mode, radio
signals are received on FMI and processed by the FM
front-end circuitry. In AM mode, radio signals are
received on AMI and processed by the AM front-end
circuitry. In audio AUXIN ADC mode, stereo audio
signals on LIN/RIN are sampled, converted to digital,
The Si473x-D60 provides highly-accurate digital AM
tuning without factory adjustments. To offer maximum
flexibility, the receiver supports a wide range of ferrite
loop sticks from 180–450 µH. An air loop antenna is
supported by using a transformer to increase the
effective inductance from the air loop. Using a 1:5 turn
ratio inductor, the inductance is increased by 25 times
and easily supports all typical AM air loop antennas
which generally vary between 10 and 20 µH.
2
filtered, and decimated to 32, 44.1, or 48 kHz for the I S
digital audio interface. In addition to the receiver mode,
there is a clocking mode to choose to clock the Si473x-
D60 from a reference clock or crystal. On the Si473x-
D60, there is an audio output mode to choose between
an analog and/or digital audio output. In the analog
audio output mode, ROUT and LOUT are used for the
audio output pins. In the digital audio mode, DOUT,
DFS, and DCLK pins are used. Concurrent
analog/digital audio output mode is also available
requiring all five pins.
4.5. SW Receiver
The Si4734/35 is the first fully integrated IC to support
AM and FM, as well as short wave (SW) band reception
from 2.3 to 26.1 MHz fully covering the 120 meter to
11 meter bands. The Si4734/35 offers extensive
shortwave features such as continuous digital tuning
with minimal discrete components and no factory
adjustments. Other SW features include adjustable
channel step sizes in 1 kHz increments, adjustable
channel bandwidth settings, advanced seek algorithm,
and soft mute.
4.3. FM Receiver
The Si473x-D60 FM receiver is based on the proven
Si4700/01 FM tuner. The receiver uses a digital low-IF
architecture allowing the elimination of external The Si4734/35 uses the FM antenna to capture short
components and factory adjustments. The Si473x-D60 wave signals. These signals are then fed directly into
integrates a low noise amplifier (LNA) supporting the the AMI pin in a wide band configuration. See "AN332:
worldwide FM broadcast band (64 to 108 MHz). An Si47xx Programming Guide” and “AN383: Si47xx
AGC circuit controls the gain of the LNA to optimize Antenna and Schematic Guidelines" for more details.
sensitivity and rejection of strong interferers. An image-
4.6. LW Receiver
reject mixer downconverts the RF signal to low-IF. The
quadrature mixer output is amplified, filtered, and The Si4734/35 supports the long wave (LW) band from
digitized with high resolution analog-to-digital 153 to 279 kHz. The highly integrated Si4734/35 offers
converters (ADCs). This advanced architecture allows continuous digital tuning with minimal discrete
the Si473x-D60 to perform channel selection, FM components and no factory adjustments. The Si4734/35
demodulation, and stereo audio processing to achieve also offers adjustable channel step sizes in 1 kHz
superior performance compared to traditional analog increments, adjustable channel bandwidth settings,
architectures.
advanced seek algorithm, and soft mute.
The Si4734/35 uses a separate ferrite bar antenna to
capture long wave signals.
4.4. AM Receiver
The highly-integrated Si473x-D60 supports worldwide
AM band reception from 520 to 1710 kHz using a digital
low-IF architecture with a minimum number of external
components and no manual alignment required. This
digital low-IF architecture allows for high-precision
filtering offering excellent selectivity and SNR with
minimum variation across the AM band. The DSP also
provides adjustable channel step sizes in 1 kHz
increments, AM demodulation, soft mute, seven
different channel bandwidth filters, and additional
features, such as a programmable automatic volume
control (AVC) maximum gain allowing users to adjust
the level of background noise.
4.7. Stereo Audio AUXIN ADC
The Si473x-D60 stereo audio AUXIN ADC can be
multiplexed between low-IF input for radio operation
and analog audio input for high fidelity data conversion
at 32, 44.1, or 48 kHz sample rate. When operated in
ADC-mode, the Si473x-D60 supports I2S digital audio
output only (no analog output) while enabling the analog
inputs and the stereo ADC.
Similar to the FM receiver, the integrated LNA and AGC
24
Rev. 1.1
Si4730/31/34/35-D60
4.8. Digital Audio Interface
The digital audio interface operates in slave mode and
supports a variety of MSB-first audio data formats
including I2S and left-justified modes. The interface has
three pins: digital data input (DIN), digital frame
synchronization input (DFS), and
a
digital bit
synchronization input clock (DCLK). The Si473x-D60
supports a number of industry-standard sampling rates
including 32, 44.1, and 48 kHz. The digital audio
interface enables low-power operation by eliminating
the need for redundant DACs and ADCs on the audio
baseband processor.
4.8.1. Audio Data Formats
The digital audio interface operates in slave mode and
supports three different audio data formats:
I2S
Left-Justified
DSP Mode
In I2S mode, by default the MSB is captured on the
second rising edge of DCLK following each DFS
transition. The remaining bits of the word are sent in
order, down to the LSB. The left channel is transferred
first when the DFS is low, and the right channel is
transferred when the DFS is high.
In left-justified mode, by default the MSB is captured on
the first rising edge of DCLK following each DFS
transition. The remaining bits of the word are sent in
order, down to the LSB. The left channel is transferred
first when the DFS is high, and the right channel is
transferred when the DFS is low.
In DSP mode, the DFS becomes a pulse with a width of
1DCLK period. The left channel is transferred first,
followed right away by the right channel. There are two
options in transferring the digital audio data in DSP
mode: the MSB of the left channel can be transferred on
the first rising edge of DCLK following the DFS pulse or
on the second rising edge.
In all audio formats, depending on the word size, DCLK
frequency, and sample rates, there may be unused
DCLK cycles after the LSB of each word before the next
DFS transition and MSB of the next word. In addition, if
preferred, the user can configure the MSB to be
captured on the falling edge of DCLK via properties.
The number of audio bits can be configured for 8, 16,
20, or 24 bits.
4.8.2. Audio Sample Rates
The device supports a number of industry-standard
sampling rates including 32, 44.1, and 48 kHz. The
digital audio interface enables low-power operation by
eliminating the need for redundant DACs on the audio
baseband processor.
Rev. 1.1
25
Si4730/31/34/35-D60
INVERTED
(OFALL = 1)
DCLK
(OFALL = 0)
DCLK
DFS
LEFT CHANNEL
I2S
RIGHT CHANNEL
(OMODE = 0000)
1 DCLK
1 DCLK
n-2
DOUT
1
2
3
n-1
n
n-2
n-1
1
2
3
n
MSB
LSB
MSB
LSB
Figure 8. I2S Digital Audio Format
INVERTED
DCLK
(OFALL = 1)
(OFALL = 0)
DCLK
DFS
LEFT CHANNEL
RIGHT CHANNEL
n-2
Left-Justified
(OMODE = 0110)
DOUT
1
2
3
n-2
n-1
n
n-1
n
1
2
3
MSB
LSB
MSB
LSB
Figure 9. Left-Justified Digital Audio Format
(OFALL = 0)
DCLK
DFS
RIGHT CHANNEL
n-2
LEFT CHANNEL
n-2
DOUT
1
2
3
2
n-1
n
(OMODE = 1100)
(OMODE = 1000)
1
2
3
2
n-1
n
(MSB at 1st rising edge)
MSB
LSB
MSB
LSB
LEFT CHANNEL
n-2
1 DCLK
RIGHT CHANNEL
n-2
DOUT
1
3
n-1
n
1
3
n-1
n
(MSB at 2nd rising edge)
MSB
LSB
MSB
LSB
Figure 10. DSP Digital Audio Format
26
Rev. 1.1
Si4730/31/34/35-D60
4.9. Stereo Audio Processing
4.10. Received Signal Qualifiers
The output of the FM demodulator is a stereo The quality of a tuned signal can vary depending on
multiplexed (MPX) signal. The MPX standard was many factors including environmental conditions, time of
developed in 1961, and is used worldwide. Today's day, and position of the antenna. To adequately manage
MPX signal format consists of left + right (L+R) audio, the audio output and avoid unpleasant audible effects to
left – right (L–R) audio, a 19 kHz pilot tone, and the end-user, the Si473x-D60 monitors and provides
RDS/RBDS data as shown in Figure 11 below.
indicators of the signal quality, allowing the host
processor to perform additional processing if required
by the customer. The Si473x-D60 monitors signal
quality metrics including RSSI, SNR, and multipath
interference on FM signals. These metrics are used to
optimize signal processing and are also reported to the
host processor. The signal processing algorithms can
Mono Audio
Left + Right
Stereo
Pilot
Stereo Audio
Left - Right
RDS/
RBDS
use
either
Silicon
Labs'
optimized
settings
(recommended) or be customized to modify
performance.
0
15 19 23
38
53 57
Frequency (kHz)
4.11. Volume Control
Figure 11. MPX Signal Spectrum
The audio output may be muted. Volume is adjusted
digitally by the RX_VOLUME property.
4.9.1. Stereo Decoder
The Si473x-D60's
integrated
stereo
decoder
4.12. Stereo DAC
automatically decodes the MPX signal using DSP
techniques. The 0 to 15 kHz (L+R) signal is the mono
output of the FM tuner. Stereo is generated from the
(L+R), (L–R), and a 19 kHz pilot tone. The pilot tone is
used as a reference to recover the (L–R) signal. Output
left and right channels are obtained by adding and
subtracting the (L+R) and (L–R) signals respectively.
High-fidelity stereo digital-to-analog converters (DACs)
drive analog audio signals onto the LOUT and ROUT
pins. The audio output may be muted.
4.13. Soft Mute
The soft mute feature is available to attenuate the audio
outputs and minimize audible noise in very weak signal
conditions. The soft mute feature is triggered by the
SNR metric. The SNR threshold for activating soft mute
is programmable, as are soft mute attenuation levels
and attack and release rates.
4.9.2. Stereo-Mono Blending
Adaptive noise suppression is employed to gradually
combine the stereo left and right audio channels to a
mono (L+R) audio signal as the signal quality degrades
to maintain optimum sound fidelity under varying
reception conditions. Three metrics, received signal
strength indicator (RSSI), signal-to-noise ratio (SNR),
4.14. FM Hi-Cut Control
Hi-cut control is employed on audio outputs with
degradation of the signal due to low SNR and/or
multipath interference. Two metrics, SNR and multipath
interference, are monitored concurrently in forcing hi-cut
of the audio outputs. Programmable minimum and
maximum thresholds are available for both metrics. The
transition frequency for hi-cut is also programmable with
up to seven hi-cut filter settings. A single set of attack
and release rates for hi-cut are programmable for both
metrics from a range of 2 ms to 64 s. The level of hi-cut
applied can be monitored with the FM_RSQ_STATUS
command. Hi-cut can be disabled by setting the hi-cut
filter to audio bandwidth of 15 kHz.
and
multipath
interference,
are
monitored
simultaneously in forcing a blend from stereo to mono.
The metric which reflects the minimum signal quality
takes precedence and the signal is blended
appropriately.
All three metrics have programmable stereo/mono
thresholds and attack/release rates. If a metric falls
below its mono threshold, the signal is blended from
stereo to full mono. If all metrics are above their
respective stereo thresholds, then no action is taken to
blend the signal. If a metric falls between its mono and
stereo thresholds, then the signal is blended to the level
proportional to the metric’s value between its mono and
stereo thresholds, with an associated attack and
release rate.
Rev. 1.1
27
Si4730/31/34/35-D60
The Si473x-D60 uses RSSI, SNR, and AFC to qualify
stations. Most of these variables have programmable
thresholds for modifying the seek function according to
customer needs.
4.15. De-emphasis
Pre-emphasis and de-emphasis is a technique used by
FM broadcasters to improve the signal-to-noise ratio of
FM receivers by reducing the effects of high-frequency
interference and noise. When the FM signal is
RSSI is employed first to screen all possible candidate
stations. SNR and AFC are subsequently used in
screening the RSSI qualified stations. The more
thresholds the system engages, the higher the
confidence that any found stations will indeed be valid
broadcast stations. The Si473x-D60 defaults set RSSI
to a mid-level threshold and add an SNR threshold set
to a level delivering acceptable audio performance. This
trade-off will eliminate very low RSSI stations while
keeping the seek time to acceptable levels. Generally,
the time to auto-scan and store valid channels for an
entire FM band with all thresholds engaged is very short
depending on the band content. Seek is initiated using
the FM_SEEK_START command. The RSSI, SNR, and
AFC threshold settings are adjustable using properties.
transmitted,
a
pre-emphasis filter is applied to
accentuate the high audio frequencies. The Si473x-D60
incorporates a de-emphasis filter which attenuates high
frequencies to restore a flat frequency response. Two
time constants are used in various regions. The de-
emphasis time constant is programmable to 50 or 75 µs
and is set by the FM_DEEMPHASIS property.
4.16. RDS/RBDS Processor
(Si4731/35 Only)
The Si4731/35 implements an RDS/RBDS* processor
for symbol decoding, block synchronization, error
detection, and error correction.
The Si4731/35 device is user configurable and provides
an optional interrupt when RDS is synchronized, loses
synchronization, and/or the user configurable RDS
FIFO threshold has been met.
4.19. Reference Clock
The Si473x-D60 reference clock is programmable,
supporting RCLK frequencies listed in Table 12,
“Reference Clock and Crystal Characteristics,” on
page 18. Refer to Table 2, “DC Characteristics,” on
page 6 for switching voltage levels and Table 12 for
frequency tolerance information.
The Si4731/35 reports RDS decoder synchronization
status and detailed bit errors in the information word for
each RDS block with the FM_RDS_STATUS command.
The range of reportable block errors is 0, 1–2, 3–5, or
6+. More than six errors indicates that the
corresponding block information word contains six or
more non-correctable errors or that the block checkword
contains errors. The pilot does not have to be present to
decode RDS/RBDS.
An onboard crystal oscillator is available to generate the
32.768 kHz reference when an external crystal and load
capacitors are provided. Refer to "2. Typical Application
Schematic" on page 20. This mode is enabled using the
POWER_UP command. Refer to “AN332: Si47xx
Programming Guide”.
*Note: RDS/RBDS is referred to only as RDS throughout the
remainder of this document.
The Si473x-D60 performance may be affected by data
activity on the SDIO bus when using the integrated
internal oscillator. SDIO activity results from polling the
tuner for status or communicating with other devices
that share the SDIO bus. If there is SDIO bus activity
while the Si473x-D60 is performing the seek/tune
function, the crystal oscillator may experience jitter,
which may result in mistunes, false stops, and/or lower
SNR.
4.17. Tuning
The tuning frequency is directly programmed using the
FM_TUNE_FREQ and AM_TUNE_FREQ commands.
The Si473x-D60 supports channel spacing steps of
10 kHz in FM mode and 1 kHz in AM mode.
4.18. Seek
The Si473x-D60 seek functionality is performed
completely on-chip and will search up or down the
selected frequency band for a valid channel. A valid
For best seek/tune results, Silicon Laboratories
recommends that all SDIO data traffic be suspended
during Si473x-D60 seek and tune operations. This is
achieved by keeping the bus quiet for all other devices
on the bus, and delaying tuner polling until the tune or
seek operation is complete. The seek/tune complete
(STC) interrupt should be used instead of polling to
determine when a seek/tune operation is complete.
channel is qualified according to
a
series of
programmable signal indicators and thresholds. The
seek function can be made to stop at the band edge and
provide an interrupt, or wrap the band and continue
seeking until arriving at the original departure frequency.
The device sets interrupts with found valid stations or, if
the seek results in zero found valid stations, the device
indicates failure and again sets an interrupt. Refer to
“AN332: Si47xx Programming Guide”.
28
Rev. 1.1
Si4730/31/34/35-D60
edges of SCLK. The Si473x-D60 acknowledges each
data byte by driving SDIO low for one cycle, on the next
falling edge of SCLK. The user may write up to 8 data
bytes in a single 2-wire transaction. The first byte is a
command, and the next seven bytes are arguments.
4.20. Control Interface
A serial port slave interface is provided, which allows an
external controller to send commands to the Si473x-
D60 and receive responses from the device. The serial
port can operate in two bus modes: 2-wire mode and 3-
wire mode. The Si473x-D60 selects the bus mode by
sampling the state of the GPO1 and GPO2 pins on the
rising edge of RST. The GPO1 pin includes an internal
pull-up resistor, which is connected while RST is low,
and the GPO2 pin includes an internal pull-down
resistor, which is connected while RST is low.
Therefore, it is only necessary for the user to actively
drive pins which differ from these states. See Table 16.
For read operations, after the Si473x-D60 has
acknowledged the control byte, it will drive an 8-bit data
byte on SDIO, changing the state of SDIO on the falling
edge of SCLK. The user acknowledges each data byte
by driving SDIO low for one cycle, on the next falling
edge of SCLK. If a data byte is not acknowledged, the
transaction will end. The user may read up to 16 data
bytes in a single 2-wire transaction. These bytes contain
the response data from the Si473x-D60.
Table 16. Bus Mode Select on Rising Edge of
RST
A 2-wire transaction ends with the STOP condition,
which occurs when SDIO rises while SCLK is high.
For details on timing specifications and diagrams, refer
to Table 4, “2-Wire Control Interface Characteristics” on
page 9; Figure 2, “2-Wire Control Interface Read and
Write Timing Parameters,” on page 10, and Figure 3, “2-
Wire Control Interface Read and Write Timing Diagram,”
on page 10.
Bus Mode
2-Wire
3-Wire
GPO1
1
0 (must drive)
GPO2
0
0
After the rising edge of RST, the pins GPO1 and GPO2
are used as general purpose output (O) pins, as
described in Section “4.21. GPO Outputs”. In any bus
4.20.2. 3-Wire Control Interface Mode
mode, commands may only be sent after V and V
supplies are applied.
D
A
When selecting 3-wire mode, the user must ensure that
a rising edge of SCLK does not occur within 300 ns
before the rising edge of RST.
In any bus mode, before sending a command or reading
a response, the user must first read the status byte to
ensure that the device is ready (CTS bit is high).
The 3-wire bus mode uses the SCLK, SDIO, and SEN_
pins. A transaction begins when the user drives SEN
low. Next, the user drives a 9-bit control word on SDIO,
which is captured by the device on rising edges of
SCLK. The control word consists of a 9-bit device
address (A7:A5 = 101b), a read/write bit (read = 1, write
= 0), and a 5-bit register address (A4:A0).
4.20.1. 2-Wire Control Interface Mode
When selecting 2-wire mode, the user must ensure that
SCLK is high during the rising edge of RST, and stays
high until after the first start condition. Also, a start
condition must not occur within 300 ns before the rising
edge of RST.
For write operations, the control word is followed by a
16-bit data word, which is captured by the device on
rising edges of SCLK.
The 2-wire bus mode uses only the SCLK and SDIO
pins for signaling. A transaction begins with the START
condition, which occurs when SDIO falls while SCLK is
high. Next, the user drives an 8-bit control word serially
on SDIO, which is captured by the device on rising
edges of SCLK. The control word consists of a 7-bit
device address, followed by a read/write bit (read = 1,
write = 0). The Si473x-D60 acknowledges the control
word by driving SDIO low on the next falling edge of
SCLK.
For read operations, the control word is followed by a
delay of one-half SCLK cycle for bus turn-around. Next,
the Si473x-D60 will drive the 16-bit read data word
serially on SDIO, changing the state of SDIO on each
rising edge of SCLK.
A transaction ends when the user sets SEN high, then
pulses SCLK high and low one final time. SCLK may
either stop or continue to toggle while SEN is high.
Although the Si473x-D60 will respond to only a single
device address, this address can be changed with the
SEN pin (note that the SEN pin is not used for signaling
in 2-wire mode). Refer to “AN332: Si47xx Programming
Guide”
In 3-wire mode, commands are sent by first writing each
argument to register(s) 0xA1–0xA3, then writing the
command word to register 0xA0. A response is
retrieved by reading registers 0xA8–0xAF.
For details on timing specifications and diagrams, refer
to Table 5, “3-Wire Control Interface Characteristics,” on
page 11; Figure 4, “3-Wire Control Interface Write
For write operations, the user then sends an 8-bit data
byte on SDIO, which is captured by the device on rising
Rev. 1.1
29
Si4730/31/34/35-D60
Timing Parameters,” on page 11, and Figure 5, “3-Wire
Control Interface Read Timing Parameters,” on page 11.
4.25. Programming with Commands
To ease development time and offer maximum
customization, the Si473x-D60 provides a simple yet
powerful software interface to program the receiver. The
device is programmed using commands, arguments,
properties, and responses.
4.21. GPO Outputs
The Si473x-D60 provides three general-purpose output
pins. The GPO pins can be configured to output a
constant low, constant high, or high-impedance. The
GPO pins can be reconfigured as specialized functions.
To perform an action, the user writes a command byte
and associated arguments, causing the chip to execute
the given command. Commands control an action such
as powerup the device, shut down the device, or tune to
a station. Arguments are specific to a given command
and are used to modify the command.
4.22. Firmware Upgrades
The Si473x-D60 contains on-chip program RAM to
accommodate minor changes to the firmware. This
allows Silicon Labs to provide future firmware updates
to optimize the characteristics of new radio designs and Properties are a special command argument used to
those already deployed in the field.
modify the default chip operation and are generally
configured immediately after powerup. Examples of
properties are de-emphasis level, RSSI seek threshold,
4.23. Reset, Powerup, and Powerdown
Setting the RST pin low will disable analog and digital and soft mute attenuation threshold.
circuitry, reset the registers to their default settings, and
Responses provide the user information and are
echoed after a command and associated arguments are
issued. All commands provide a 1-byte status update,
disable the bus. Setting the RST pin high will bring the
device out of reset.
A powerdown mode is available to reduce power indicating interrupt and clear-to-send status information.
consumption when the part is idle. Putting the device in
powerdown mode will disable analog and digital circuitry
properties for the Si473x-D60, see “AN332: Si47xx
while keeping the bus active.
Programming Guide.”
For a detailed description of the commands and
4.24. 2 V Operation (SSOP Only)
The Si473x-D60 is capable of operating down to 2 V as
the battery drains in an application. Any power-up or
reset is not guaranteed to work below the DC
characteristics defined in Table 2. This capability
enables a much longer run time in battery operated
devices.
30
Rev. 1.1
Si4730/31/34/35-D60
5. Pin Descriptions
5.1. Si473x-D60-GM
20 19 18 17
NC
FMI
1
16
2
15 DOUT/[LIN]
14 LOUT/[DFS]
13 ROUT/[DOUT]
12 GND
RFGND
AMI
3
4
5
GND
PAD
RST
6
11 VA
7
8
9
10
Pin Number(s)
Name
NC
Description
1, 20
No connect. Leave floating.
2
FMI
FM RF inputs. FMI should be connected to the antenna trace.
RF ground. Connect to ground plane on PCB.
AM RF input. AMI should be connected to the AM antenna.
Device reset input (active low).
3
RFGND
AMI
4
5
RST
6
Serial enable input (active low).
SEN
7
SCLK
SDIO
RCLK
Serial clock input.
8
Serial data input/output.
9
External reference oscillator input.
10
V
Digital and I/O supply voltage.
D
11
V
Analog supply voltage. May be connected directly to battery.
Ground. Connect to ground plane on PCB.
A
12, GND PAD
GND
13
14
15
ROUT/[DOUT] Right audio line output for analog output mode.
LOUT/[DFS] Left audio line output for analog output mode.
DOUT/[LIN] Digital output data for digital output mode or Left channel input for AUXIN ADC
mode.
16
17
DFS/[RIN]
Digital frame synchronization input for digital output mode or Right channel input
for AUXIN ADC mode.
GPO3/[DCLK] General purpose output, crystal oscillator, or digital bit synchronous clock input
in digital output mode.
18
19
General purpose output or interrupt pin.
General purpose output.
GPO2/[INT]
GPO1
Rev. 1.1
31
Si4730/31/34/35-D60
5.2. Si473x-D60-GU
DOUT/[LIN]
DFS/[RIN]
GPO3/[DCLK]
GPO2/[INT]
GPO1
1
2
24
23
22
21
20
19
18
17
16
15
14
13
LOUT/[DFS]
ROUT/[DOUT]
3
DBYP
VA
4
VD
5
NC
RCLK
SDIO
SCLK
SEN
RST
GND
GND
6
NC
7
FMI
8
RFGND
NC
9
10
11
12
NC
AMI
Pin Number(s)
Name
Description
1
DOUT/[LIN] Digital output data for digital output mode or Left channel input for AUX IN ADC
mode.
2
3
DFS/[RIN]
Digital frame synchronization input for digital output mode or Right channel input
for AUXIN ADC mode.
GPO3/[DCLK] General purpose output, crystal oscillator, or digital bit synchronous clock input
in digital output mode.
4
5
GPO2/[INT] General purpose output or interrupt pin.
GPO1
NC
General purpose output.
6,7
8
No connect. Leave floating.
FMI
FM RF inputs. FMI should be connected to the antenna trace.
RF ground. Connect to ground plane on PCB.
Unused. Tie these pins to GND.
9
RFGND
NC
10,11
12
AMI
AM/SW/LW RF input.
13,14
GND
Ground. Connect to ground plane on PCB.
15
RST
Device reset input (active low).
16
17
18
19
20
SEN
SCLK
SDIO
RCLK
Serial enable input (active low).
Serial clock input.
Serial data input/output.
External reference oscillator input.
Digital and I/O supply voltage.
V
D
21
Analog supply voltage. May be connected directly to battery.
Bypass capacitor.
V
A
22
23
24
DBYP
ROUT/[DOUT] Right audio line output in analog output mode.
LOUT/[DFS] Left audio line output in analog output mode.
32
Rev. 1.1
Si4730/31/34/35-D60
6. Ordering Guide
1
Description
Package
Type
Operating
Temperature/Voltage
Part Number
Si4730-D60-GM
QFN
Pb-free
–20 to 85 °C
2.7 to 5.5 V
AM/FM Broadcast Radio Receiver
2
Si4730-D60-GU
Si4731-D60-GM
SSOP
Pb-free
QFN
Pb-free
–20 to 85 °C
2.7 to 5.5 V
AM/FM Broadcast Radio Receiver with
RDS/RBDS
2
Si4731-D60-GU
Si4734-D60-GM
SSOP
Pb-free
QFN
Pb-free
–20 to 85 °C
2.7 to 5.5 V
AM/FM/SW/LW Broadcast Radio Receiver
2
Si4734-D60-GU
Si4735-D60-GM
SSOP
Pb-free
QFN
Pb-free
–20 to 85 °C
2.7 to 5.5 V
AM/FM/SW/LW Broadcast Radio Receiver
with RDS/RBDS
2
Si4735-D60-GU
SSOP
Pb-free
Notes:
1. Add an “(R)” at the end of the device part number to denote tape and reel option.
2. SSOP devices operate down to V = 2 V at 25 °C.
A
Rev. 1.1
33
Si4730/31/34/35-D60
7. Package Outline
7.1. Si473x-D60 QFN
Figure 12 illustrates the package details for the Si473x. Table 17 lists the values for the dimensions shown in the
illustration.
Figure 12. 20-Pin Quad Flat No-Lead (QFN)
Table 17. Package Dimensions
Symbol
Millimeters
Nom
Symbol
Millimeters
Nom
Min
Max
Min
Max
A
A1
b
0.50
0.00
0.20
0.27
0.55
0.02
0.60
0.05
0.30
0.37
f
2.53 BSC
L
0.35
0.00
—
0.40
—
0.45
0.10
0.05
0.05
0.08
0.10
0.10
0.25
L1
c
0.32
aaa
bbb
ccc
ddd
eee
—
D
3.00 BSC
1.70
—
—
D2
e
1.65
1.75
—
—
0.50 BSC
3.00 BSC
1.70
—
—
E
—
—
E2
1.65
1.75
Notes:
1. All dimensions are shown in millimeters (mm) unless otherwise noted.
2. Dimensioning and tolerancing per ANSI Y14.5M-1994.
34
Rev. 1.1
Si4730/31/34/35-D60
7.2. Si473x-D60 SSOP
Figure 13 illustrates the package details for the Si473x. Table 18 lists the values for the dimensions shown in the
illustration.
Figure 13. 24-Pin SSOP
Table 18. Package Dimensions
Dimension
Min
—
Nom
—
Max
1.75
0.25
0.30
0.25
A
A1
b
0.10
0.20
0.10
—
—
c
—
D
8.65 BSC
6.00 BSC
3.90 BSC
0.635 BSC
—
E
E1
e
L
0.40
0°
1.27
8°
L2
θ
0.25 BSC
—
aaa
bbb
ccc
ddd
0.20
0.18
0.10
0.10
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MO-137, Variation AE.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification
for Small Body Components.
Rev. 1.1
35
Si4730/31/34/35-D60
8. PCB Land Pattern
8.1. Si473x-D60 QFN
Figure 14 illustrates the PCB land pattern details for the Si473x-D60-GM QFN. Table 19 lists the values for the
dimensions shown in the illustration.
Figure 14. PCB Land Pattern
36
Rev. 1.1
Si4730/31/34/35-D60
Table 19. PCB Land Pattern Dimensions
Symbol
Millimeters
Min Max
2.71 REF
1.60 1.80
Symbol
Millimeters
Min
Max
D
D2
e
GE
W
2.10
—
—
0.34
0.28
0.50 BSC
2.71 REF
X
—
E
Y
0.61 REF
E2
f
1.60
2.53 BSC
2.10
1.80
ZE
ZD
—
—
3.31
3.31
GD
—
Notes: General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification.
3. This Land Pattern Design is based on IPC-SM-782 guidelines.
4. All dimensions shown are at Maximum Material Condition (MMC). Least Material
Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
Notes: Solder Mask Design
1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the
solder mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Notes: Stencil Design
1. A stainless steel, laser-cut, and electro-polished stencil with trapezoidal walls should
be used to assure good solder paste release.
2. The stencil thickness should be 0.125 mm (5 mils).
3. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads.
4. A 1.45 x 1.45 mm square aperture should be used for the center pad. This provides
approximately 70% solder paste coverage on the pad, which is optimum to assure
correct component stand-off.
Notes: Card Assembly
1. A No-Clean, Type-3 solder paste is recommended.
2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification
for Small Body Components.
Rev. 1.1
37
Si4730/31/34/35-D60
8.2. Si473x-D60 SSOP
Figure 15 illustrates the PCB land pattern details for the Si473x-D60-GU SSOP. Table 20 lists the values for the
dimensions shown in the illustration.
Figure 15. PCB Land Pattern
Table 20. PCB Land Pattern Dimensions
Dimension
Min
Max
C
E
5.20
5.30
0.635 BSC
X
0.30
1.50
0.40
1.60
Y1
General:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. This land pattern design is based on the IPC-7351 guidelines.
Solder Mask Design:
3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the
solder mask and the metal pad is to be 60 µm minimum, all the way around the pad.
Stencil Design:
4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should
be used to assure good solder paste release.
5. The stencil thickness should be 0.125 mm (5 mils).
6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads.
Card Assembly:
7. A No-Clean, Type-3 solder paste is recommended.
8. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification
for Small Body Components.
38
Rev. 1.1
Si4730/31/34/35-D60
9. Top Markings
9.1. Si473x-D60 Top Marking (QFN)
3460
3560
3060 3160
DTTT
DTTT
YWW
YWW
DTTT
YWW
DTTT
YWW
9.2. Top Marking Explanation (QFN)
Mark Method:
YAG Laser
Line 1 Marking:
Part Number
30 = Si4730, 31 = Si4731, 34 = Si4734, 35 = Si4735.
60 = Firmware Revision 6.0.
D = Revision D Die.
Firmware Revision
Die Revision
Line 2 Marking:
Line 3 Marking:
TTT = Internal Code
Internal tracking code.
Circle = 0.5 mm Diameter Pin 1 Identifier.
(Bottom-Left Justified)
Y = Year
Assigned by the Assembly House. Corresponds to the last
significant digit of the year and work week of the mold date.
WW = Workweek
Rev. 1.1
39
Si4730/31/34/35-D60
9.3. Si473x-D60 Top Marking (SSOP)
473XD60GU
YYWWTTTTTT
9.4. Top Marking Explanation (SSOP)
Mark Method:
YAG Laser
4730 = Si4730; 4731 = Si4731; 4734 = Si4734;
4735 = Si4735.
Part Number
Die Revision
D = Revision D die.
Line 1 Marking:
Firmware Revision
Package Type
60 = Firmware Revision 6.0.
GU = 24-pin SSOP Pb-free package
YY = Year
Line 2 Marking:
WW = Work week
TTTTTT = Manufacturing code
Assigned by the Assembly House.
40
Rev. 1.1
Si4730/31/34/35-D60
10. Additional Reference Resources
Contact your local sales representatives for more information or to obtain copies of the following references:
EN55020 Compliance Test Certificate
AN332: Si47xx Programming Guide
AN383: Si47xx Antenna, Schematic, Layout, and Design Guidelines
AN388: Si470x/1x/2x/3x/4x Evaluation Board Test Procedure
Si47xx EVB User’s Guide
Customer Support Site: www.silabs.com
This site contains all application notes, evaluation board schematics and layouts, and evaluation software. NDA
is required for complete access. Please visit the Silicon Labs Technical Support web page:
https://www.silabs.com/support/pages/contacttechnicalsupport.aspx and register to submit a technical support
request.
Rev. 1.1
41
Si4730/31/34/35-D60
DOCUMENT CHANGE LIST
Revision 1.0 to Revision 1.1
Updated part number throughout.
Updated pin assignments on front page.
Updated block diagram on front page.
Updated Table 6, “Digital Audio Interface
Characteristics,” on page 12.
Updated Table 12, “Reference Clock and Crystal
Characteristics,” on page 18.
Added Table 13, “Thermal Conditions,” on page 18.
Updated Section "2. Typical Application Schematic"
on page 20.
Updated Section "4. Functional Description" on page
23.
Updated Section "5. Pin Descriptions" on page 31.
42
Rev. 1.1
Si4730/31/34/35-D60
NOTES:
Rev. 1.1
43
Si4730/31/34/35-D60
CONTACT INFORMATION
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Tel: 1+(512) 416-8500
Fax: 1+(512) 416-9669
Toll Free: 1+(877) 444-3032
Email: FMinfo@silabs.com
Internet: www.silabs.com
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from
the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features
or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, rep-
resentation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation conse-
quential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to
support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where per-
sonal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap-
plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.
44
Rev. 1.1
相关型号：
SI4732CY-T1-E3
IC BUF OR INV BASED PRPHL DRVR, PDSO16, ROHS COMPLIANT, SOP-16, Peripheral Driver
VISHAY
©2020 ICPDF网 联系我们和版权申明