U631H16 [SIMTEK]
SimtekSoftStore 2K x 8 nvSRAM; SimtekSoftStore 2K ×8的nvSRAM型号: | U631H16 |
厂家: | SIMTEK CORPORATION |
描述: | SimtekSoftStore 2K x 8 nvSRAM |
文件: | 总13页 (文件大小:133K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Obsolete - Not Recommended for New Designs
U631H16
SimtekSoftStore 2K x 8 nvSRAM
Features
Description
integrity.
• High-performance CMOS nonvola- The U631H16 has two separate
Once a STORE cycle is initiated,
further input or output are disabled
until the cycle is completed.
Because a sequence of addresses
is used for STORE initiation, it is
important that no other read or
write accesses intervene in the
sequence or the sequence will be
aborted.
Internally, RECALL is a two step
procedure. First, the SRAM data is
cleared and second, the nonvola-
tile information is transferred into
the SRAM cells.
The RECALL operation in no way
alters the data in the EEPROM
cells. The nonvolatile data can be
recalled an unlimited number of
times.
tile static RAM 2048 x 8 bits
• 25, 35 and 45 ns Access Times
• 12, 20 and 25 ns Output Enable
Access Times
modes of operation: SRAM mode
and nonvolatile mode. In SRAM
mode, the memory operates as an
ordinary static RAM. In nonvolatile
operation, data is transferred in
parallel from SRAM to EEPROM or
from EEPROM to SRAM. In this
mode SRAM functions are disab-
led.
• Software STORE Initiation
(STORE Cycle Time < 10 ms)
• Automatic STORE Timing
• 106 STORE cycles to EEPROM
• 100 years data retention in
EEPROM
• Automatic RECALL on Power Up
• Software RECALL Initiation
(RECALL Cycle Time < 20 μs)
• Unlimited RECALL cycles from
EEPROM
The U631H16 is a fast static RAM
(25, 35, 45 ns), with a nonvolatile
electrically
erasable
PROM
(EEPROM) element incorporated
in each static memory cell. The
SRAM can be read and written an
unlimited number of times, while
independent nonvolatile data resi-
des in EEPROM.
Data transfers from the SRAM to
the EEPROM (the STORE opera-
tion), or from the EEPROM to the
SRAM (the RECALL ) operation)
are initiated through software
sequences.
• Unlimited Read and Write to
SRAM
• Single 5 V ± 10 % Operation
• Operating temperature ranges:
0 to 70 °C
-40 to 85 °C
• QS 9000 Quality Standard
• ESD protection > 2000 V
(MIL STD 883C M3015.7-HBM)
• RoHS compliance and Pb- free
• Packages: PDIP28 (600 mil)
SOP24 (300 mil)
The U631H16 combines the high
performance and ease of use of a
fast SRAM with nonvolatile data
Pin Description
Pin Configuration
28
27
26
25
24
23
22
21
20
19
18
1
n.c.
n.c.
A7
VCC
W
1
A7
A6
24
23
22
21
20
19
18
17
16
15
14
13
2
VCC
A8
2
3
n.c.
A8
Signal Name Signal Description
3
A5
4
A6
A9
A0 - A10
Address Inputs
Data In/Out
4
A4
5
A5
A9
W
5
A3
6
A4
n.c.
G
G
DQ0 - DQ7
PDIP
28
6
A2
7
A3
A10
E
SOP
24
Chip Enable
E
7
A1
8
A2
A10
E
Output Enable
Write Enable
Power Supply Voltage
Ground
G
8
A0
9
A1
DQ7
DQ6
DQ5
DQ4
DQ3
W
9
DQ0
DQ1
DQ2
VSS
10
11
12
13
14
A0
DQ7
DQ6
DQ5
DQ4
DQ3
VCC
VSS
10
11
12
DQ0
DQ1
DQ2
VSS
17
16
15
Top View
Top View
March 31, 2006
STK Control #ML0042
1
Rev 1.0
U631H16
Block Diagram
EEPROM Array
32 x (64 x 8)
VCC
VSS
STORE
RECALL
A5
A6
A7
A8
A9
SRAM
Array
32 Rows x
64 x 8 Columns
Store/
Recall
Control
VCC
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
Column I/O
Software
Detect
Column Decoder
A0 - A10
G
A0 A1 A2 A3 A4A10
DQ7
E
W
Truth Table for SRAM Operations
Operating Mode
E
W
G
DQ0 - DQ7
Standby/not selected
Internal Read
Read
H
L
L
L
High-Z
High-Z
*
*
H
H
H
L
L
Data Outputs Low-Z
Data Inputs High-Z
Write
*
* H or L
Characteristics
All voltages are referenced to VSS = 0 V (ground).
All characteristics are valid in the power supply voltage range and in the operating temperature range specified.
Dynamic measurements are based on a rise and fall time of ≤ 5 ns, measured between 10 % and 90 % of VI, as well as
input levels of VIL = 0 V and VIH = 3 V. The timing reference level of all input and output signals is 1.5 V,
with the exception of the tdis-times and ten-times, in which cases transition is measured ± ±200 mV from steady-state voltage.
Absolute Maximum Ratingsa
Symbol
Min.
Max.
Unit
Power Supply Voltage
Input Voltage
VCC
VI
-0.5
-0.3
-0.3
7
V
V
VCC+0.5
VCC+0.5
1
Output Voltage
VO
PD
V
Power Dissipation
W
Operating Temperature
C-Type
K-Type
0
-40
70
85
°C
°C
Ta
Storage Temperature
Tstg
-65
150
°C
a: Stresses greater than those listed under „Absolute Maximum Ratings“ may cause permanent damage to the device. This is a stress
rating only, and functional operation of the device at condition above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Rev 1.0
March 31, 2006
STK Control #ML0042
2
U631H16
Recommended Operation
Conditions
Symbol
Conditions
Min.
Max.
Unit
Power Supply Voltage
Input Low Voltage
Input High Voltage
VCC
VIL
4.5
-0.3
2.2
5.5
0.8
V
V
V
-2 V at Pulse Width
10 ns permitted
VIH
VCC+0.3
C-Type
K-Type
DC Characteristics
Symbol
Conditions
Unit
Min. Max. Min. Max.
Operating Supply Currentb
ICC1
VCC
VIL
VIH
= 5.5 V
= 0.8 V
= 2.2 V
tc
tc
tc
= 25 ns
= 35 ns
= 45 ns
90
80
75
95
85
80
mA
mA
mA
Average Supply Current during
STOREc
ICC2
VCC
E
W
VIL
VIH
= 5.5 V
6
7
mA
≥ VCC-0.2 V
≥ VCC-0.2 V
≤ 0.2 V
≥ VCC-0.2 V
Standby Supply Currentd
(Cycling TTL Input Levels)
ICC(SB)1
VCC
E
= 5.5 V
≥±VIH
tc
tc
tc
= 25 ns
= 35 ns
= 45 ns
30
23
20
34
27
23
mA
mA
mA
Average Supply Current
at tcR = 200 nsb
(Cycling CMOS Input Levels)
ICC3
VCC
W
VIL
VIH
= 5.5 V
15
15
mA
≥ VCC-0.2 V
≤ 0.2 V
≥ VCC-0.2 V
Standby Supply Currentd
(Stable CMOS Input Levels)
ICC(SB)
VCC
E
VIL
VIH
= 5.5 V
1
1
mA
≥ VCC-0.2 V
≤ 0.2 V
≥ VCC-0.2 V
b: ICC1 and ICC3 are dependent on output loading and cycle rate. The specified values are obtained with outputs unloaded.
The current ICC1 is measured for WRITE/READ - ratio of 1/2.
c: ICC2 is the average current required for the duration of the STORE cycle (STORE Cycle Time).
d: Bringing E±≥±VIH will not produce standby current levels until any nonvolatile cycle in progress has timed out. See MODE SELECTION
table. The current ICC(SB)1 is measured for WRITE/READ - ratio of 1/2.
March 31, 2006
STK Control #ML0042
3
Rev 1.0
U631H16
C-Type
K-Type
DC Characteristics
Symbol
Conditions
Unit
Min. Max. Min. Max.
VCC
IOH
IOL
= 4.5 V
=-4 mA
= 8 mA
Output High Voltage
Output Low Voltage
VOH
VOL
2.4
8
2.4
8
V
V
0.4
-4
0.4
-4
VCC
VOH
VOL
= 4.5 V
= 2.4 V
= 0.4 V
Output High Current
Output Low Current
IOH
IOL
mA
mA
Input Leakage Current
VCC
= 5.5 V
High
Low
IIH
IIL
VIH
VIL
= 5.5 V
1
1
μA
μA
=
0 V
-1
-1
-1
-1
Output Leakage Current
VCC
= 5.5 V
High at Three-State- Output
Low at Three-State- Output
IOHZ
IOLZ
VOH
VOL
= 5.5 V
1
1
μA
μA
=
0 V
SRAM Memory Operations
Symbol
25
35
45
Switching Characteristics
No.
Unit
Read Cycle
Alt.
IEC
Min. Max. Min. Max. Min. Max.
1
2
3
4
5
6
7
8
9
Read Cycle Timef
tAVAV
tAVQV
tELQV
tcR
ta(A)
25
35
45
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Address Access Time to Data Validg
Chip Enable Access Time to Data Valid
25
25
12
13
13
35
35
20
17
17
45
45
25
20
20
ta(E)
Output Enable Access Time to Data Valid tGLQV
ta(G)
tdis(E)
tdis(G)
ten(E)
ten(G)
tv(A)
E HIGH to Output in High-Zh
G HIGH to Output in High-Zh
E LOW to Output in Low-Z
tEHQZ
tGHQZ
tELQX
5
0
3
0
5
0
3
0
5
0
3
0
G LOW to Output in Low-Z
tGLQX
tAXQX
tELICCH
tEHICCL
Output Hold Time after Addr. Changeg
10 Chip Enable to Power Activee
11 Chip Disable to Power Standbyd, e
25
35
45
e: Parameter guaranteed but not tested.
f: Device is continuously selected with E and G both LOW.
g: Address valid prior to or at the same time with E transition LOW.
h: Measured ± ±200 mV from steady state output voltage.
Rev 1.0
March 31, 2006
STK Control #ML0042
4
U631H16
f
=
=
VIL, W = VIH)
Read Cycle 1: Ai-controlled (during Read cycle: E
G
tcR
(1)
Ai
Address Valid
ta(A)
(2)
DQi
Output
Output Data Valid
Previous Data Valid
tv(A)
(9)
Read Cycle 2: G-, E-controlled (during Read cycle: W = VIH)g
tcR
(1)
Ai
E
Address Valid
ta(A)
tPD
(11)
(2)
ta(E) (3)
tdis(E) (5)
ten(E) (7)
G
ta(G)
(4)
tdis(G) (6)
ten(G) (8)
DQi
Output
High Impedance
Output Data Valid
t
PU (10)
ACTIVE
ICC
STANDBY
Symbol
Alt. #1 Alt. #2
25
35
45
Switching Characteristics
Write Cycle
Unit
No.
IEC
Min. Max. Min. Max. Min. Max.
12 Write Cycle Time
tAVAV
tAVAV
tcW
tw(W)
tsu(W)
tsu(A)
tsu(A-WH)
tsu(E)
tw(E)
25
20
20
0
35
30
30
0
45
35
35
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
13 Write Pulse Width
tWLWH
14 Write Pulse Width Setup Time
15 Address Setup Time
tWLEH
tAVEL
tAVEH
tAVWL
tAVWH
tELWH
16 Address Valid to End of Write
17 Chip Enable Setup Time
18 Chip Enable to End of Write
19 Data Setup Time to End of Write
20 Data Hold Time after End of Write
21 Address Hold after End of Write
22 W LOW to Output in High-Zh, i
23 W HIGH to Output in Low-Z
20
20
20
12
0
30
30
30
18
0
35
35
35
20
0
tELEH
tDVEH
tEHDX
tEHAX
tDVWH
tWHDX
tWHAX
tWLQZ
tWHQX
tsu(D)
th(D)
th(A)
0
0
0
tdis(W)
ten(W)
10
13
15
5
5
5
March 31, 2006
STK Control #ML0042
5
Rev 1.0
U631H16
Write Cycle #1: W-controlledj
tcW
(12)
Ai
E
Address Valid
tsu(E)
t
(17)
h(A) (21)
tsu(A-WH)
(16)
tw(W) (13)
W
t
su(A) (15)
tsu(D)
t
h(D) (20)
(19)
Input Data Valid
ten(W)
DQi
Input
tdis(W)
(22)
(23)
High Impedance
DQi
Output
Previous Data Valid
Write Cycle #2: E-controlledj
tcW
(12)
Ai
E
Address Valid
t
su(A) (15)
tw(E)
(18)
th(A)
(21)
tsu(W)
(14)
W
t
th(D) (20)
Input Data Valid
High Impedance
su(D)(19)
DQi
Input
DQi
Output
undefined
L- to H-level
H- to L-level
i: If W is LOW and when E goes LOW, the outputs remain in the high impedance state.
>
j: E or W must be VIH during address transitions.
Rev 1.0
March 31, 2006
STK Control #ML0042
6
U631H16
Nonvolatile Memory Operations
Symbol
STORE Cycle Inhibit and
No.
Min.
Max.
Unit
Automatic Power Up RECALL
Alt.
IEC
24 Power Up RECALL Durationk, e
Low Voltage Trigger Level
tRESTORE
VSWITCH
650
4.5
μs
4.0
V
k: tRESTORE starts from the time VCC rises above VSWITCH
.
STORE Cycle Inhibit and Automatic Power Up RECALL
VCC
5.0 V
VSWITCH
t
STORE inhibit
(24)
Power Up
RECALL
tRESTORE
Software Mode Selection
A10 - A0
E
W
Mode
I/O
Power
Notes
(hex)
L
H
000
555
2AA
7FF
0F0
70F
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active
l, m
l, m
l, m
l, m
l, m
l
Nonvolatile STORE
ICC2
L
H
000
555
2AA
7FF
0F0
70E
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active
l, m
l, m
l, m
l, m
l, m
l
Nonvolatile RECALL
l: The six consecutive addresses must be in order listed (000, 555, 2AA, 7FF, 0F0, 70F) for a Store cycle or (000, 555, 2AA,
7FF, 0F0, 70E) for a RECALL cycle. W must be high during all six consecutive cycles. See STORE cycle and RECALL cycle tables and
diagrams for further details.
The following six-address sequence is used for testing purposes and should not be used: 000, 555, 2AA, 7FF, 0F0, 39C.
m: I/O state assumes that G ≤±VIL. Activation of nonvolatile cycles does not depend on the state of G.
March 31, 2006
STK Control #ML0042
7
Rev 1.0
U631H16
25
35
45
Symbol
No. Software Controlled STORE/RECALL
Cyclel, n
Unit
Alt.
tAVAV
IEC
Min. Max. Min. Max. Min. Max.
25 STORE/RECALL Initiation Time
26 Chip Enable to Output Inactiveo
27 STORE Cycle Timep
tcR
25
35
45
ns
ns
ms
μs
ns
ns
ns
tELQZ tdis(E)SR
tELQXS td(E)S
tELQXR td(E)R
tAVELN tsu(A)SR
tELEHN tw(E)SR
tEHAXN th(A)SR
600
10
600
10
600
10
28 RECALL Cycle Timeq
20
20
20
29 Address Setup to Chip Enabler
30 Chip Enable Pulse Widthr, s
31 Chip Disable to Address Changer
0
20
0
0
25
0
0
35
0
n: The software sequence is clocked with E controlled READs.
o: Once the software controlled STORE or RECALL cycle is initiated, it completes automatically, ignoring all inputs.
p: Note that STORE cycles (but not RECALL) are aborted by VCC < VSWITCH (STORE inhibit).
q: An automatic RECALL also takes place at power up, starting when VCC exceeds VSWITCH and takes tRESTORE. VCC must not drop below
VSWITCH once it has been exceeded for the RECALL to function properly.
r: Noise on the E pin may trigger multiple READ cycles from the same address and abort the address sequence.
s: If the Chip Enable Pulse Width is less than ta(E) (see Read Cycle) but greater than or equal tw(E)SR, than the data may not be valid at
the end of the low pulse, however the STORE or RECALL will still be initiated.
Software Controlled STORE/RECALL Cycler, s, t, u (E = HIGH after STORE initiation)
tcR
(25)
tcR
(25)
ADDRESS 6
ADDRESS 1
Ai
E
th(A)SR
(31)
tw(E)SR
(30)
tw(E)SR
(30)
t
dis(E)(5)
(31)
th(A)SR
tsu(A)SR
(29)
(29)
t
td(E)S
tsu(A)SR
d(E)R (28)
(27)
DQi
Output
High Impedance
VALID
tdis(E)SR
VALID
(26)
Software Controlled STORE/RECALL Cycler, s, t, u (E = LOW after STORE initiation)
tcR
(25)
ADDRESS 1
tw(E)SR
ADDRESS 6
Ai
E
th(A)SR
(31)
(30)
(29)
tsu(A)SR
(31)
(29)
th(A)SR
t
td(E)R (28)
tsu(A)SR
d(E)S (27)
DQi
Output
High Impedance
VALID
VALID
tdis(E)SR
(26)
t: W must be HIGH when E is LOW during the address sequence in order to initiate a nonvolatile cycle. G may be either HIGH or LOW
throughout. Addresses 1 through 6 are found in the mode selection table. Address 6 determines whether the U631H16 performs a STORE
or RECALL.
u: E must be used to clock in the address sequence for the Software controlled STORE and RECALL cycles.
Rev 1.0
March 31, 2006
STK Control #ML0042
8
U631H16
Test Configuration for Functional Check
5 V
w
VCC
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
480
V
IH
V
IL
VO
v
30 pF
E
W
255
G
VSS
v: In measurement of tdis-times and ten-times the capacitance is 5 pF.
w: Between VCC and VSS must be connected a high frequency bypass capacitor 0.1 μF to avoid disturbances.
Capacitancee
Conditions
Symbol
Min.
Max.
Unit
VCC = 5.0 V
Input Capacitance
CI
8
pF
VI
f
= VSS
= 1 MHz
= 25 °C
Output Capacitance
CO
7
pF
Ta
All pins not under test must be connected with ground by capacitors.
Ordering Code
Example
U631H16 S1
C
25 G1
Leadfree Option
Type
blank= Standard Package
G1 = Leadfree Green Package
Package
D1= PDIP28 (600 mil)
S1 = SOP24 (300 mil)
Access Time
25 = 25 ns
35 = 35 ns x
45 = 45 ns x
Operating Temperature Range
C = 0 to 70 °C
K = -40 to 85 °C
x: on special request
Device Marking (example)
ZMD
Product specification
Date of manufacture
U631H16S1C
25 Z 0425
G1
(The first 2 digits indicating
the year, and the last 2
digits the calendar week.)
Internal Code
Leadfree Green Package
March 31, 2006
STK Control #ML0042
9
Rev 1.0
U631H16
Device Operation
performed, followed by parallel programming of all non-
volatile elements. Once a STORE cycle is initiated, fur-
ther inputs and outputs are disabled until the cycle is
completed.
Because a sequence of addresses is used for STORE
initiation, it is important that no other READ or WRITE
accesses intervene in the sequence or the sequence
will be aborted and no STORE or RECALL will take
place.
The U631H16 has two separate modes of operation:
SRAM mode and nonvolatile mode. In SRAM mode,
the memory operates as a standard fast static RAM. In
nonvolatile mode, data is transferred from SRAM to
EEPROM (the STORE operation) or from EEPROM to
SRAM (the RECALL operation). In this mode SRAM
functions are disabled.
To initiate the STORE cycle the following READ
sequence must be performed:
SRAM READ
The U631H16 performs a READ cycle whenever E and
G are LOW while W is HIGH. The address specified on
pins A0 - A10 determines which of the 2048 data bytes
will be accessed. When the READ is initiated by an
address transition, the outputs will be valid after a delay
of tcR. If the READ is initiated by E or G, the outputs will
be valid at ta(E) or at ta(G), whichever is later. The data
outputs will repeatedly respond to address changes
within the tcR access time without the need for transition
on any control input pins, and will remain valid until
another address change or until E or G is brought
HIGH or W is brought LOW.
1.
2.
3.
4.
5.
6.
Read address
Read address
Read address
Read address
Read address
Read address
000
555
(hex) Valid READ
(hex) Valid READ
2AA (hex) Valid READ
7FF
0F0
70F
(hex) Valid READ
(hex) Valid READ
(hex) Initiate STORE
Once the sixth address in the sequence has been
entered, the STORE cycle will commence and the chip
will be disabled. It is important that READ cycles and
not WRITE cycles are used in the sequence. It is not
necessary that G is LOW for the sequence to be valid.
After the tSTORE cycle time has been fulfilled, the SRAM
will again be activated for READ and WRITE operation.
SRAM WRITE
A WRITE cycle is performed whenever E and W are
LOW. The address inputs must be stable prior to
entering the WRITE cycle and must remain stable until
ei-ther E or W goes HIGH at the end of the cycle. The
data on pins DQ0 - 7 will be written into the memory if it
is valid tsu(D) before the end of a W controlled WRITE or
Software Nonvolatile RECALL
A RECALL cycle of the EEPROM data into the SRAM
is initiated with a sequence of READ operations in a
manner similar to the STORE initiation. To initiate the
RECALL cycle the following sequence of READ opera-
tions must be performed:
tsu(D) before the end of an E controlled WRITE.
It is recommended that G is kept HIGH during the
entire WRITE cycle to avoid data bus contention on the
common I/O lines. If G is left LOW, internal circuitry will
turn off the output buffers tdis(W) after W goes LOW.
1.
2.
3.
4.
5.
6.
Read address
Read address
Read address
Read address
Read address
Read address
000
555
(hex) Valid READ
(hex) Valid READ
2AA (hex) Valid READ
7FF
0F0
70E
(hex) Valid READ
(hex) Valid READ
(hex) Initiate RECALL
Noise Consideration
The U631H16 is a high speed memory and therefore it
must have a high frequency bypass capacitor of appro-
ximately 0.1 μF connected between VCC and VSS using
leads and traces that are as short as possible. As with
all high speed CMOS ICs, normal carefull routing of
power, ground and signals will help prevent noise pro-
blems.
Internally, RECALL is a two step procedure. First, the
SRAM data is cleared and second, the nonvolatile
information is transferred into the SRAM cells. The
RECALL operation in no way alters the data in the
EEPROM cells. The nonvolatile data can be recalled an
unlimited number of times.
Software Nonvolatile STORE
Automatic Power Up RECALL
The U631H16 software controlled STORE cycle is
initiated by executing sequential READ cycles from six
specific address locations. By relying on READ cycles
only, the U631H16 implements nonvolatile operation
while remaining compatible with standard 2K x 8
SRAMs. During the STORE cycle, an erase of the pre-
vious nonvolatile data is first
On power up, once VCC exceeds the sense voltage of
VSWITCH, a RECALL cycle is automatically initiated. The
voltage on the VCC pin must not frop belwo VSWITCH
once it has risen above it in order for the RECALL to
operate properly. Due to this automatic RECALL,
SRAM operation cannot commence until tRESTORE after
V
CC exceeds VSWITCH
.
Rev 1.0
March 31, 2006
STK Control #ML0042
10
U631H16
If the U631H16 is in a WRITE state at the end of power
up RECALL, the SRAM data will be corrupted.
Low Average Active Power
To help avoid this situation, a 10 KΩ resistor should be
The U631H16 has been designed to draw significantly
less power when E is LOW (chip enabled) but the
access cycle time is longer than 55 ns.
When E is HIGH the chip consumes only standby cur-
rent.
connected between W and VCC
.
Hardware Protection
The U631H16 offers hardware protection against inad-
vertent STORE operation through VCC sense.
For VCC < VSWITCH the software initiated STORE opera-
tion will be inhibited.
The overall average current drawn by the part depends
on the following items:
1. CMOS or TTL input levels
2. the time during which the chip is disabled (E HIGH)
3. the cycle time for accesses (E LOW)
4. the ratio of READs to WRITEs
5. the operating temperature
6. the VCC level
The information describes the type of component and shall not be considered as assured characteristics. Terms of
delivery and rights to change design reserved.
March 31, 2006
STK Control #ML0042
11
Rev 1.0
U631H16
LIFE SUPPORT POLICY
Simtek products are not designed, intended, or authorized for use as components in systems intended for surgical
implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the Simtek product could create a situation where personal injury or death may occur.
Components used in life-support devices or systems must be expressly authorized by Simtek for such purpose.
LIMITED WARRANTY
The information in this document has been carefully checked and is believed to be reliable. However, Simtek
makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any
loss or damage of whatever nature resulting from the use of, or reliance upon it. The information in this document
describes the type of component and shall not be considered as assured characteristics.
Simtek does not guarantee that the use of any information contained herein will not infringe upon the patent,
trademark, copyright, mask work right or other rights of third parties, and no patent or licence is implied hereby.
This document does not in any way extent Simtek’s warranty on any product beyond that set forth in its standard
terms and conditions of sale.
Simtek reserves terms of delivery and reserves the right to make changes in the products or specifications, or
both, presented in this publication at any time and without notice.
March 31, 2006
Change record
Date/Rev
Name
Change
01.11.2001 Ivonne Steffens
format revision and release for „Memory CD 2002“
20.04.2004 Matthias Schniebel
adding „Leadfree Green Package“ to ordering information
adding „Device Marking“
6
7.4.2005
Stefan Günther
delete PDIP28 (300mil) and SOP28 (300mil), add 10 endurance
cycles and 100a data retention and ESD protection > 2000V
31.3.2006
1.0
Troy Meester
Simtek
changed to obsolete status
Assigned Simtek Document Control Number
相关型号:
U631H16BD1C25G1
2KX8 NON-VOLATILE SRAM, 25ns, PDIP28, 0.600 INCH, LEAD FREE, PLASTIC, DIP-28
CYPRESS
U631H16BD1C35G1
2KX8 NON-VOLATILE SRAM, 35ns, PDIP28, 0.600 INCH, LEAD FREE, PLASTIC, DIP-28
CYPRESS
U631H16BD1C45G1
2KX8 NON-VOLATILE SRAM, 45ns, PDIP28, 0.600 INCH, LEAD FREE, PLASTIC, DIP-28
CYPRESS
U631H16BD1K25G1
2KX8 NON-VOLATILE SRAM, 25ns, PDIP28, 0.600 INCH, LEAD FREE, PLASTIC, DIP-28
CYPRESS
U631H16BD1K35G1
2KX8 NON-VOLATILE SRAM, 35ns, PDIP28, 0.600 INCH, LEAD FREE, PLASTIC, DIP-28
CYPRESS
U631H16BD1K45G1
Non-Volatile SRAM, 2KX8, 45ns, CMOS, PDIP28, 0.600 INCH, LEAD FREE, PLASTIC, DIP-28
SIMTEK
©2020 ICPDF网 联系我们和版权申明