SP7661_1 [SIPEX]
Evaluation Board Manual; 评估板手册
| 型号： | SP7661_1 |
| 厂家： | 
SIPEX CORPORATION |
| 描述： | Evaluation Board Manual |
| 文件： | 总11页 (文件大小：386K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Solved by
SP7661
TM
Evaluation Board Manual
Easy Evaluation of the SP7661ER
0 to 3A Output Synchronous Buck
Converter
Built in Power MOSFETs
UVLO Detects Both VCC and VIN
Highly Integrated Design, Minimal
Components
High Efficiency: up to 90%
Feature Rich: UVIN, Programmable
Soft Start, Built In VCC Supply
Output Short Circuit Protection and
Current Limiting
SP7661EB Schematic
Nov27-06
SP7661 Evaluation Board Manual
Page 1 of 11
© 2006 Sipex Corporation
Using the Evaluation Board
1) Powering Up the SP7661EB Circuit
Connect the SP7661 Evaluation Board with an external +12V power supply. Connect with short
leads and large diameter wire directly to the “VIN” and “GND” posts. Connect a Load between
the VOUT and GND posts, again using short leads with large diameter wire to minimize
inductance and voltage drops.
2) Measuring Output Load Characteristics
VOUT ripple can best be seen by touching the probe tip to the pad for C5 and the scope GND
collar touching Output GND post – avoid a GND lead on the scope which will increase noise
pickup.
3) Using the Evaluation Board with Different Output Voltages
While the SP7661 Evaluation Board has been tested and delivered with the output set to 3.30V,
by simply changing one resistor, R2, the SP7661 can be set to other output voltages. The
relationship in the Equation 1 is based on a voltage divider from the output to the feedback pin
VFB, which is set to an internal reference voltage of 0.80V. Note, due to the common mode
voltage range of the current sense amplifier, output voltages greater than 3.3V are only possible
if the current sense is disabled. To disable current limit, remove R3 and R4. Standard 1%
metal film resistors of surface mount size 0603 are recommended.
R1
Vout
.80V
Equation 1
R2 =
(
− 1)
Where R1 = 10kΩ and for VOUT = 0.80V setting, simply remove R2 from the board.
Furthermore, one could select the value of the R1 & R2 combination to meet the exact output
voltage setting by restricting R1 resistance range such that 10kΩ ≤ R1 ≤ 100kΩ for overall
system loop stability.
Note that since the SP7661 Evaluation Board design was optimized for 12V down conversion to
3.30V, changes of output voltage and/or input voltage will alter performance from the data given
in the Power Supply Data section. In addition, the SP7661ER provides short circuit protection by
sensing VOUT at GND. The current limit of the converter is set to about 5.5A which is
accomplished by sensing the current through the inductor. To adjust the current limit, follow
Equations 2 and 3 to set the current limit accordingly. The current limit should be set to about
50% higher than the maximum output current that is desired. This will prevent the part from
accidentally triggering the current limit during large transient load steps.
Adjusting the current upwards is done by adjusting resistor R9.
60mV ⋅ (R3 + R4)
R9 =
Equation 2
Imax ⋅ (DCR - 60mV)
Where
DCR is the Inductor winding resistance
IMAX is the desired output current
Feb21-07
SP7661 Evaluation Manual
Page 2 of 11
©2007 Sipex Corporation
Adjusting the current downwards is controlled by adjusting R8.
(Vout - 60mV) + (Imax ⋅ DCR)
Equation 3
R8 = R4 ⋅
60mV - (Imax ⋅ DCR)
Where
DCR is the Inductor winding resistance and
IMAX is the desired output current
Further details on the current limit can be found in the SP7661 data sheet. For the Wurth
Inductor on this demo board, DCR= 14mΩ nominal.
POWER SUPPLY DATA
The SP7661ER is designed with an accurate 2.0% reference over line, load and
temperature. Figure 1 data shows a typical SP7661 evaluation board efficiency plot, with
efficiencies up to 90% and output currents up to 3A. The output voltage ripple of less than 10mV
at full load and the LX node are shown in figure 2. Figures 3 and 4 illustrate a 0A to 3A and 1A
to 3A Load Step. Short circuit and current limit are shown in Figures 5 and 6. Typical startup
characteristics into a full load and no load are shown in figure 7 and 8. All data was taken at
12VIN.
While data on individual power supply boards may vary, the capability of the SP7661ER
of achieving high accuracy over a range of load conditions shown here is quite impressive and
desirable for accurate power supply design.
7661 Efficiency
12Vin, 3.3Vout, 3Amps
95.0
90.0
85.0
80.0
75.0
70.0
65.0
60.0
55.0
50.0
0.5
1
1.5
2
2.5
3
Iout (Amps)
Figure 1. Efficiency vs. Load
Feb21-07
SP7661 Evaluation Manual
Page 3 of 11
©2007 Sipex Corporation
Vout
Vout
Iout 1A/div
Figure 2. LX node output & ripple voltage
Figure 3. Load Step Response: 0->3A
Vout
Vout
Soft Start
Iout 2A/div
Iout 1A/div
Figure 4. Load Step Response 1->3A
Figure 5. Current limit set point ~6A
Vin
Vout
Vout
Soft Start
Soft Start
Iout 2A/div
Iin 5A/div
Figure 6. Output Short Circuit w/IIN
Figure 7. Startup into full load
©2007 Sipex Corporation
Feb21-07
SP7661 Evaluation Manual
Page 4 of 11
VOUT
Soft Start
IOUT 2A/div
Figure 8. Current Limit Re-start Rate
TYPE III LOOP COMPENSATION DESIGN
The open loop gain of the SP7661EB can be divided into the gain of the error amplifier
Gamp(s), PWM modulator Gpwm, buck converter output stage Gout(s), and feedback resistor
divider Gfbk. In order to cross over at the selecting frequency fco, the gain of the error amplifier
must compensate for the attenuation caused by the rest of the loop at this frequency. The goal
of loop compensation is to manipulate the open loop frequency response such that its gain
crosses over 0dB at a slope of –20dB/dec. The open loop crossover frequency should be higher
than the ESR zero of the output capacitors but less than 1/5 to 1/10 of the switching frequency
fs to insure proper operation. Since the SP7661EB is designed with Ceramic Type output
capacitors, a Type III compensation circuit is required to give a phase boost of 180° in order to
counteract the effects of the output LC underdamped resonance double pole frequency.
Feb21-07
SP7661 Evaluation Manual
Page 5 of 11
©2007 Sipex Corporation
Figure 9. Voltage Mode Control Loop with Loop Dynamic for Type III Compensation
The simple guidelines for positioning the poles and zeros and for calculating the
component values for Type III compensation are as follows. As a particular example, consider
for the following SP7661EB with a Type III Voltage Loop Compensation component selections:
Input requirements and inductor selection
Vin = 12V, we will use 12V as Vin max for this design.
Vout = 3.30V @ 0 to 3A load
Select L = 2.2uH => yield ≈ 60% of maximum 3A output current ripple.
Select Cout = 100uF Ceramic capacitor (Resr ≈ 3mΩ) Given the performance of ceramic caps
we will use ~80% of the output capacitance in calcualations.
fs = 600khz SP7661 internal Oscillator Frequency
Vramp_pp = 1.0V SP7661 internal Ramp Peak to Peak Amplitude
Feb21-07
SP7661 Evaluation Manual
Page 6 of 11
©2007 Sipex Corporation
Step by step design procedures:
Note: Loop Compensation component calculations discussed in this
section are further elaborated in the application note #ANP16, “Loop
Compensation of Voltage-Mode Buck Converters”.
These calculations shown here can be quickly iterated with the Type III
Loop Compensation Calculator on the web at:
www.sipex.com/files/Application-Notes/TypeIIICalculator.xls
fco = fs/10
Choose
fco = 600Khz/10 = 60Khz
Calculate fp_LC, the double pole frequency of the filter
1
fp_LC =
2π ( L ⋅ C)
1
fp_LC =
= 11.99kHz ≈ 12kHz
2π ⋅ 2.2uH ⋅80uF)
Calculate fz_ESR , the ESR zero frequency
1
fz_ESR =
2π ⋅⋅Cout
1
fz _ ESR =
= 663kHz
2π ⋅(3mΩ)⋅(80µF)
Select R1 component value such that 10kΩ ≤ R1 ≤ 100kΩ
R1 = 10kΩ, 1%
Calculate R2 base on the desired VOUT
R1
R2 =
Vout
−1
.8V
10KΩ
R2 =
= 3200Ω ≈ 3160Ω
3.3V
.8V
−1
Feb21-07
SP7661 Evaluation Manual
Page 7 of 11
©2007 Sipex Corporation
Select the ratio of RZ2 / R1 gain for the desired gain bandwidth (from above, we will use 60kHz)
Vramp _ pp
Vin_ max
fco
fp _ LC
RZ2 = R1⋅
⋅
1V
12V
60kHz
12kHz
RZ2 = R1⋅
⋅
= 4166Ω ≅ 4020Ω
Calculate CZ2 by placing the zero at ½ of the output filter pole frequency
1
CZ2 =
π ⋅ RZ2⋅ fp _ LC
1
CZ2 =
= 6.59nF ≈ 6.8nF
π ⋅4020Ω⋅12kHz
Calculate CP1 by placing the first pole at ESR zero frequency
1
CP1 =
2π ⋅(Rz2⋅ fz _ ESR)
1
CP1=
= 59.7 pF ≈ 56pF
2π ⋅ (4020 ⋅ 663KHz)
Calculate RZ3 by setting the second pole at ½ of the switching frequency and the second zero
at the output filter double pole frequency
2⋅(R1) ⋅( fp _ LC)
RZ3 =
fs − 2 fp _ LC
2⋅(10kΩ) ⋅(12kHz)
600KHz −12kHz
RZ3 =
= 408Ω ≅ 400Ω
Calculate CZ3 from RZ3 component value above
1
CZ3 =
π ⋅ RZ3⋅ fs
1
CZ3 =
=1.3nF ≈1500 pF
π ⋅400Ω ⋅600KHz
Choose 100pF ≤ CF1 ≤ 220pF to stabilize the SP7661ER internal Error Amplifier. For this
example let’s select 100pF.
Feb21-07
SP7661 Evaluation Manual
Page 8 of 11
©2007 Sipex Corporation
PC LAYOUT DRAWINGS
Figure 10. SP7661EB Component Placement
Figure 11. SP7661EB PC Layout Top Side
Figure 12. SP7661EB PC Layout 2nd Layer Side
Feb21-07
SP7661 Evaluation Manual
Page 9 of 11
©2007 Sipex Corporation
Figure 13. SP7661EB PC Layout 3rd Layer Side
Figure 14. SP7661EB PC Layout Bottom Side
Figure 15. SP7661EB PC Layout Bottom Side Components
Feb21-07
SP7661 Evaluation Manual
Page 10 of 11
©2007 Sipex Corporation
Table 1: SP7661EB Suggested Components and Vendor Lists
ORDERING INFORMATION
Model
Temperature Range
Package Type
SP7661EB…................................-40°C to +85°C...............…………….SP7661 Evaluation Board
SP7661ER..............................…. -40°C to +85°C...................................……26-pin DFN(option2)
For further assistance:
Email:
Sipexsupport@sipex.com
WWW Support page:
Live Technical Chat:
Sipex Application Notes:
Type III Loop Compensation
Calculator:
http://www.sipex.com/content.aspx?p=support
http://www.geolink-group.com/sipex/
http://www.sipex.com/applicationNotes.aspx
www.sipex.com/files/Application-Notes/TypeIIICalculator.xls
Sipex Corporation
Solved by
Headquarters and
Sales Office
233 South Hillview Drive
Milpitas, CA95035
tel: (408) 934-7500
faX: (408) 935-7600
TM
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product
or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Feb21-07
SP7661 Evaluation Manual
Page 11 of 11
©2007 Sipex Corporation
相关型号：
©2020 ICPDF网 联系我们和版权申明