SPX29301T5-L-1.8/TR [SIPEX]
Fixed Positive LDO Regulator, 1.8V, PSSO5, LEAD FREE, TO-263BB, 5 PIN;
| 型号： | SPX29301T5-L-1.8/TR |
| 厂家： | 
SIPEX CORPORATION |
| 描述： | Fixed Positive LDO Regulator, 1.8V, PSSO5, LEAD FREE, TO-263BB, 5 PIN 输出元件 调节器 |
| 文件： | 总11页 (文件大小：173K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
®
SPX29300/01/02/03
3A High Current, Low Dropout Voltage Regulator
Adjustable & Fixed Output, Fast Response Time
FEATURES
■ Adjustable Output Down To 1.25V
■ 1% Output Accuracy
■ Output Current of 3A
SPX29300
3 Pin TO-263
1
2
3
■ Low Dropout Voltage of 450mV @ 3A
■ Extremely Tight Load and Line
Regulation
■ Extremely Fast Transient Response
■ Reverse-Battery Protection
■ Zero Current Shutdown (5 pin version)
■ Error Flag Signal Output for Out of
Regulation State (5 pin version)
VIN
VOUT
GND
Now Available in Lead Free Packaging
APPLICATIONS
■ Powering VGA & Sound Card
■ Power PC™ Supplies
■ SMPS Post Regulator
■ High Efficiency “Green” Computer
Systems
■ Standard TO-220 and TO-263
Packages
■ High Efficiency Linear Power Supplies
■ Constant Current Regulators
■ Adjustable Power Supplies
■ Battery Charger
DESCRIPTION
The SPX29300/01/02/03 are 3A, highly accurate voltage regulators with a low drop out
voltage of 450mV dropout (typical) @ 3A. These regulators are specifically designed for low
voltage applications that require a low dropout voltage and a fast transient response. They
are fully fault protected against over-current, reverse battery, and positive and negative
voltage transients. On-Chip trimming adjusts the reference voltage to 1% initial accuracy.
Other features in the 5 pin versions include Enable, and Error Flag.
The SPX29300/01/02/03 are offered in 3 & 5-pin TO-220 & TO-263 packages. For a 1.5A
version, refer to the SPX29150 data sheet.
TYPICAL APPLICATIONS CIRCUITS
SPX29302
1
2
4
V
V
OUT
1
SPX29300
3
IN
VOUT
V
IN
+
+
5
3
10µF
R1
6.8µF
2
+
+
10µF
ADJ
6.8µF
GND
R2
Figure 1. Fixed Output Linear Regulator
Figure 2. Adjustable Output Linear Regulator
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
1
ABSOLUTE MAXIMUM RATINGS
Lead Temperature (soldering, 5 seconds) ................260°C
Storage Temperature Range........................-65°C to +150°C
Operating Junction Temperature Range......-40°C to +125°C
Input Voltage (Note 1) .................................................... 16V
ELECTRICAL CHARACTERISTICS
(Note 1) at VIN=VOUT + 1V and IOUT = 10mA, CIN = 6.8µF, COUT = 10µF, TA = 25°C, unless otherwise specified. The Boldface
applies over the junction temperature range.
SPX29300/01
PARAMETER
Fixed Voltage Options
1.8V Version
CONDITIONS
TYP
MIN
MAX
UNITS
Output Voltage
IOUT = 10mA
10mA ≤ IOUT ≤ 3A, 2.8V ≤ VIN ≤ 16V
1.800
1.800
1.782
1.764
1.818
1.836
V
V
V
V
2.5V Version
Output Voltage
IOUT = 10mA
10mA ≤ IOUT ≤ 3A, 3.5V ≤ VIN ≤ 16V
2.500
2.500
2.475
2.450
2.525
2.550
3.3V Version
Output Voltage
IOUT = 10mA
10mA ≤ IOUT ≤ 3A, 4.3V ≤ VIN ≤ 16V
3.300
3.300
3.267
3.234
3.333
3.366
5.0V Version
Output Voltage
IOUT = 10mA
5.000
4.950
5.050
10mA ≤ IOUT ≤ 3A, 6.0V ≤ VIN ≤ 16V
5.000
4.900
5.100
All Voltage Options
Line Regulation
Load Regulation
∆V/∆T
SPX29300/01/02/03
0.06
IOUT=10mA,(VOUT+1V) ≤ VIN ≤ 16V
VIN=VOUT+1V, 10mA≤ IOUT ≤ IFL (Note 2)
VOUT Temp Coefficient (Note 6)
0.5
1
%
%
0.2
20
100
175
ppm/°C
mV
Dropout Voltage, except IOUT=100mA
50
1.8V, (Note 3)
IOUT=1.5A
IOUT=3.0A
150
450
700
35
Ground Current
(Note 5)
IOUT=1.5A
IOUT=3.0A
10
37
mA
mA
Ground Pin Current
at Dropout
VIN=0.5V less than specified VOUT,
IOUT=10mA
0.9
Current Limit
VOUT=0V (Note 4)
4.5
3.0
A
Output Noise Voltage
(10Hz to 100kHz)
IL=100mA
CL=10µF
400
µVRMS
CL=33µF
260
Reference Voltage
Adjustable version only
1.240
1.228
1.252
V
1.215
1.265
Reference Voltage
Adjustable version only (Note 8)
(Note 7)
1.203
1.277
V
Adjust Pin Bias Current
40
20
80
120
nA
Reference Voltage
Temp. Coeff.
ppm/°C
nA/°C
Adjust Pin Bias
0.1
Current Temp. Coeff.
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
2
ELECTRICAL CHARACTERISTICS
at VIN=VOUT + 1V and IOUT = 10mA, CIN = 6.8µF, COUT = 10µF, TA = 25°C, unless otherwise specified. The Boldface applies
over the junction temperature range. Adjustable versions are set to 5.0V.
PARAMETER
CONDITIONS
TYP
MIN
MAX
UNITS
FLAG OUTPUT (ERROR COMPARATOR)
SPX29301/03
Output Leakage
Current
VOH=16V
0.01
220
60
1
2
µA
mV
mV
mV
mV
Output Low Voltage
Device set for 5V,VIN=4.5V, IOL=250µA
Device set for 5V, (Note 9)
Device set for 5V, (Note 9)
Device set for 5V, (Note 9)
300
400
Upper Threshold
Voltage
40
25
Lower Threshold
Voltage
75
95
140
Hysteresis
15
ENABLE Input
SPX29301/02
Input Logic Voltage
Low (OFF)
VIN<10V
0.8
V
High (ON)
2.4
ENABLE Input Pin
VEN=16V
VEN=0.8V
100
10
600
750
1
µA
µA
2
Regulator Output
(Note 10)
500
µA
Current in Shutdown
Thermal Resistance
TO-200 Junction to Case, at Tab
TO-220 Junction to Ambient
TO-263 Junction to Case, at Tab
TO-263 Junction to Ambient
3
60
3
°C/W
60
NOTES:
Note 1: Maximum positive supply voltage of 20V must be of limited duration (<100ms) and duty cycle of less than 1%. The maximum continuous supply
voltage is 16V.
Note 2: Full load current (I ) is defined as 3.0A.
FL
Note 3: Dropout voltage is defined as the input to output differential when the output voltage drops to 99% of its nominal value.
Note 4: V = V
+1V. For example, use V = 4.3V for a 3.3V regulator. Employ pulse-testing procedures to minimize temperature rise.
IN
IN
OUT (NOMINAL)
Note 5: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the load current to the ground current.
Note 6: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range
Note 7: Thermal regulation is defined as the change in output voltage at time T after a change in power dissipation is applied, excluding load / line regulation effects.
Specifications for a 200mA load pulse as V = 20V (a 4W pulse) for t = 10ms.
IN
Note 8: V
≤ V
OUT
≤ (V -1), 2.3V≤V ≤ 16V, 10mA ≤ I ≤ I , T < T
.
jmax
REF
IN
IN
L
FL
j
Note 9: Comparator threshold is expressed in terms of a voltage differential at the Adjust terminal below the nominal reference voltage measured 6V input. To
express these thresholds in terms of output voltage change, multiply the error amplifier gain = V /V = (R1 + R2)/R2. For example, at a programmable
OUT REF
output voltage of 5V, the Error output is guaranteed to go low when the output drops by 95mVx 5V/ 1.240V = 38mV. Threshold remain constant as a percent of
as V is varied, with the dropout warning occurring at typically 5% below nominal, 7.7% guaranteed.
V
OUT
OUT
Note 10: V ≤ 0.8V and V ≤ 16V, V = 0.
OUT
EN
IN
BLOCK DIAGRAM
IN
OUT
O.V
ILIMIT
1.180V
FLAG
1.240V
28V
R1*
Reference
+
-
+
-
ADJ
EN
Thermal
Shutdown
R2*
GND
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
3
TYPICAL PERFORMANCE CHARACTERISTICS
1200
1000
800
2.540
2.530
2.520
2.510
600
400
2.500
2.490
85°C
25°C
2.480
2.470
2.5V Device
IL = 10mA
CL = 10µF
3.3V Device
CL = 10µF
Vin = 3.2V
200
0
2.460
4
6
8
10
Vin (V)
12
14
16
0
1.0
2.0
3.0
IL (A)
Figure 3. Dropout Voltage vs Load Current
Figure 4. Line Regulation
80.0
70.0
3.310
3.305
3.300
3.295
3.290
60.0
25°C
50.0
40.0
30.0
85°C
3.3V Device
Vin = 4.3V
CL = 10µF
20.0
10.0
3.3V Device
Vin = 4.3V
CL = 10µF
3.285
3.280
0.0
0
1.0
2.0
3.0
0
1.0
2.0
3.0
IL (A)
IL (A)
Figure 5. Ground Current vs Load Current
Figure 6. Load Regulation
1.9
1.8
1.7
1.6
1.5
3.3V Device
1.4
1.3
1.2
-40
-20
0
20
40
60
80
100
120
Temperature (o C)
Figure 7. Enable Threshold vs Temperature
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
4
APPLICATION INFORMATION
The SPX29300/01/02/03 incorporates protec-
tion against over-current faults, reversed load
insertion, over temperature operation, and
positive and negative transient voltage.
response is needed. If the power source has a
high AC impedance, a 0.1µF ceramic capaci-
tor between input & ground is recommended.
Minimum Load Current
Thermal Considerations
To ensure a proper behavior of the regulator
under light load, a minimum load of 5mA for
SPX29300/01/02/03 is required.
Although the SPX29300/01/02/03 offers
limiting circuitry for overload conditions, it is
still necessary to insure that the maximum
junction temperature is not exceeded in the
application. Heat will flow through the lowest
resistance path, the junction-to-case path. In
order to insure the best thermal flow of the
component, proper mounting is required.
Adjustable Regulator Design
The SPX29302/03 are adjustable regulators
that can be programmed to any value between
1.25V and 16V using 2 resistors, R1 and R2.
The relationship between the resistors is:
R1 = R2(Vout/1.240-1).
TO-220 Design Example:
Assume that VIN = 10V, VOUT = 5V, IOUT
=
Error Flag
1.5A, TA = 50°C, θHA= 1°C/W, θCH= 2°C/W,
and θJC= 3C°/W, where:
TA = ambient temperature,
θHA= heatsink to ambient thermal
resistance
The SPX29301/03 features an error flag that
indicates either an over current or under
voltage condition. The flag output goes low,
sinking 10mA when either condition occurs.
θCH= case to heatsink thermal
resistance
θJC = junction to case thermal
resistance
Enable Input
The SPX29301/02 have an Enable function
that switches the regulator on and off. Their
thresholds are TTL compatible. When the
regulator is active, approximately 20 uA flows
through the Enable pin.
The power calculated under these conditions
is:
PD = (VIN – VOUT) * IOUT = 7.5W.
Typical Application Circuits
And the junction temperature is calculated as
TJ = TA + PD * (θHA + θCH + θJC) or
TJ = 50 + 7.5 * (1+2+3) = 95°C
Figure 1 represents at typical fixed output
regulator. Figure 2 represents an adjustable
output regulator. The values of R1 and R2 set
the output voltage value as follows:
Reliable operation is insured.
VOUT =VREF * [1 + (R1/R2)].
For best results, the total series resistance
should be small enough to pass a minimum
regulator load current of 5 mA. A minimum
value of 10kohms is recommended for R2
with a range between 10kohms and 47 kohms.
Capacitor Requirements
The output capacitor is needed to insure
stability and minimize the output noise. The
value of the capacitor varies with the load.
However, a minimum value of 10µF alumi-
num capacitor will guarantee stability over all
load conditions. A tantalum capacitor is
recommended if a faster load transient
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
5
PACKAGE: 3 PIN TO-220
A
E
B
E/2
E2
SEATING
PLANE
A
øP
Q
A1
H1
D
D1
CHAMFER
OPTIONAL
L1
1
D
D
C
C
L
b
A
e
C
e1
A2
3 PIN TO-220
JEDEC TO-220
(AB) Variation
Dimensions in
(mm)
MIN NOM MAX
b
A
.140
.020
-
-
.190
.055
A1
A2
b
WITH PLATING
.080
-
.115
.015 .027 .040
b2
c
.045
.014
.560
-
.070
.024
.650
c
-
-
D
D1
.330
.480
.380
.270
-
-
-
-
-
.355
.507
.420
.350
BASE METAL
CONTACT AREA
D2
E
E1
E2
e
-
.030
.100 BSC
.200 BSC
e1
.230
-
.270
.250
H1
L1
-
-
3 PIN TO-220
-
-
-
L2
.139
.100
-
.161
.135
∆P
Q
-
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
6
PACKAGE: 5 PIN TO-220
E
A
B
E/2
SEATING
PLANE
A
øP
Q
F
H1
D
D
D1
L1
CHAMFER
OPTIONAL
D
D
C
C
L
A
b
e
C1
e1
J1
Dimensions in
(inches)
5 PIN TO-220
MIN NOM MAX
A
b
.160
-
.190
.040
.022
.590
.415
.015
.014
.560
.385
.385
.062
-
C1
D
-
-
-
-
-
E
e
.415
.072
e1
.045
.234
.090
.540
-
.055
.258
.115
.560
.250
F
H1
-
-
-
-
J1
L
L1
∆P
Q
.146
-
-
.156
.103
.113
5 PIN TO-220
U
-
-
.30
.24
-
-
V
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
7
PACKAGE: 3 PIN TO-263
SEATING PLANE
A
E
E/2
C2
L1
D
H
1
2
3
B
B
c
e
See View C
b
b2
SEATING
PLANE
GAUGE PLANE
0º-8º
A1
L
3-PIN TO-263
JEDEC TO-263
(AA) Variation
Dimensions in inches
MIN NOM MAX
View C
A
A1
b
.160
.000
-
.190
.010
-
.020
.015
.330
-
.039
.029
.380
b
c
-
-
D
WITH PLATING
c
D1
E
.270
-
-
.420
-
.380
.245
-
E1
-
e
.100 BSC
.625
H
.575
-
BASE METAL
SECTION B-B
L
.070
-
.110
.066
.070
L1
L2
L3
-
-
-
-
.010 BSC
3 PIN TO-263
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
8
PACKAGE: 5 PIN TO-263
SEATING PLANE
A
(DATUM A)
C2
H
E
1
2
3
5
4
c
L2
(E)
E
L1
D1
5X b
E1
e
4X
5 PIN TO-263
JEDEC TO-263
(BB) Variation
Dimensions in (mm)
MIN NOM MAX
A
A1
b
.160
0
-
-
-
.190
.010
.039
.029
.023
-
.020
.015
.045
.270
c
-
0º-8º
L3
c2
D1
E
-
-
L
.380
.245
-
.420
-
E1
-
(b)
e
.067 BSC
.625
WITH PLATING
c
H
.575
-
L
.070
-
.110
.066
.070
L1
L2
L3
-
-
-
-
.010 BSC
BASE METAL
CONTACT AREA
5 PIN TO-263
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
9
PACKAGE PINOUTS
TO-263-3 Package (T)
TO-263-5 Package (T5)
SPX29301
1)ENABLE
2)INPUT
3)GND
4)OUTPUT
SPX29302
1) ENABLE
2) INPUT
3) GND
4) OUTPUT
5)
ADJUST
SPX29303
1)FLAG
2)INPUT
1
2
3 4 5
1
2
3
3)
GND
4)OUTPUT
5)
5)
ADJUST
FLAG
V
V
OUT
GND
Top View
IN
Front View
TO-220-3 Package (U)
TO-220-5 Package (U5)
SPX29303
SPX29301
1)ENABLE
2)INPUT
SPX29302
1
2
3
1)
2)
3)
4)
5)
1)
2)
3)
4)
5)
ENABLE
INPUT
GND
OUTPUT
ADJUST
FLAG
INPUT
GND
OUTPUT
ADJUST
3)
4)
5)
GND
OUTPUT
FLAG
GND
IN
Front View
1 2 3 4 5
Top View
V
V
*Tab is internally connected to GND
OUT
ORDERING INFORMATION
PART NUMBER
ACCURACY OUTPUT VOLTAGE
PACKAGE
SPX29300U-1.8
SPX29300U-2.5
SPX29300U-3.3
SPX29300U-5.0
SPX29300T-1.8
SPX29300T-1.8/TR
SPX29300T-2.5
SPX29300T-2.5/TR
SPX29300T-3.3
SPX29300T-3.3/TR
SPX29300T-5.0
SPX29300T-5.0/TR
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.8V
2.5V
3.3V
5.0V
1.8V
1.8V
2.5V
2.5V
3.3V
3.3V
5.0V
5.0V
3 lead TO-220
3 lead TO-220
3 lead TO-220
3 lead TO-220
3 lead TO-263
3 lead TO-263
3 lead TO-263
3 lead TO-263
3 lead TO-263
3 lead TO-263
3 lead TO-263
3 lead TO-263
Available in lead free packaging. To order add "-L" suffix to part number.
Example: SPX29300T-5.0/TR = standard; SPX29300T-L-5.0/TR = lead free
/TR = Tape and Reel
Pack quantity is 500 for TO-263.
Sipex Corporation
Headquarters
233 South Hillview Drive
Milpitas, CA 95035
TEL: (408) 934-7500
FAX: (408) 935-7600m
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
10
ORDERING INFORMATION
PART NUMBER
ACCURACY OUTPUT VOLTAGE
PACKAGE
5 lead TO-220
5 lead TO-220
5 lead TO-220
5 lead TO-220
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-263
5 lead TO-220
5 lead TO-263
5 lead TO-263
5 lead TO-220
SPX29301U5-1.8
SPX29301U5-2.5
SPX29301U5-3.3
SPX29301U5-5.0
SPX29301T5-1.8
SPX29301T5-1.8/TR
SPX29301T5-2.5
SPX29301T5-2.5/TR
SPX29301T5-3.3
SPX29301T5-3.3/TR
SPX29301T5-5.0
SPX29301T5-5.0/TR
SPX29302T5
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.0%
1.8V
2.5V
3.3V
5.0V
1.8V
1.8V
2.5V
2.5V
3.3V
3.3V
5.0V
5.0V
Adj
SPX29302T5/TR
SPX29302U5
Adj
Adj
SPX29303T5
Adj
SPX29303T5/TR
SPX29303U5
Adj
Adj
Available in lead free packaging. To order add "-L" suffix to part number.
Example: SPX29302T5/TR = standard; SPX29302T5-L-5.0/TR = lead free
/TR = Tape and Reel
Pack quantity is 500 for TO-263.
Corporation
ANALOG EXCELLENCE
Sipex Corporation
Headquarters
233 South Hillview Drive
Milpitas, CA 95035
TEL: (408) 934-7500
FAX: (408) 935-7600m
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Date: 5/25/04
SPX29300/01/02/03 3A Low Dropout Voltage Regulator
© Copyright 2004 Sipex Corporation
11
相关型号：
SPX29301T5-L-2-5
Fixed Positive LDO Regulator, 2.5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BA, 5 PIN
SIPEX
SPX29301T5-L-2-5/TR
Fixed Positive LDO Regulator, 2.5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BA, 5 PIN
SIPEX
SPX29301T5-L-3-3/TR
Fixed Positive LDO Regulator, 3.3V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BA, 5 PIN
SIPEX
SPX29301T5-L-3-3/TR
Fixed Positive LDO Regulator, 3.3V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BA, 5 PIN
EXAR
SPX29301T5-L-3.3/TR
Fixed Positive LDO Regulator, 3.3V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BB, 5 PIN
SIPEX
SPX29301T5-L-5-0
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BA, 5 PIN
EXAR
SPX29301T5-L-5-0/TR
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BA, 5 PIN
SIPEX
SPX29301T5-L-5.0
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BB, 5 PIN
SIPEX
SPX29301T5-L-5.0/TR
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-263BB, 5 PIN
SIPEX
SPX29301U5-1.8-L
Fixed Positive LDO Regulator, 1.8V, 0.7V Dropout, PSFM5, LEAD FREE, TO-220, 5 PIN
SIPEX
SPX29301U5-5.0-L
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSFM5, LEAD FREE, TO-220, 5 PIN
SIPEX
©2020 ICPDF网 联系我们和版权申明