SKY65013-214LF [SKYWORKS]
InGaP General-Purpose Amplifier LF-6 GHz; 的InGaP通用放大器LF- 6 GHz的型号: | SKY65013-214LF |
厂家: | SKYWORKS SOLUTIONS INC. |
描述: | InGaP General-Purpose Amplifier LF-6 GHz |
文件: | 总5页 (文件大小:344K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
SKY65013-214LF: InGaP General-Purpose Amplifier
LF–6 GHz
Features
Broadband: LF–6 GHz
Functional Block Diagram
●
●
Small signal gain: 11.5 dB typ. @ 2 GHz
●
High output 3rd order intercept: 29 dBm typ.
●
0P : 12.5 dBm typ. @ 2 GHz
1 dB
●
●
●
●
Input and output impedance: 50 Ω nominal
Single, positive DC supply voltage
Plastic Micro-X package
50 Ω
50 Ω
Skyworks offers lead (Pb)-free, RoHS (Restriction of
Hazardous Substances)-compliant packaging.
NEW
Available lead (Pb)-free and RoHS-compliant MSL-1 @ 250 °C
per JEDEC J-STD-020
Applications
●
Wireless infrastructure: WLAN, HLAN, DBS, broadband, cellular
base stations
●
Test instrumentation
●
CATV
Description
The SKY65013 is lead (Pb)-free and RoHS-compliant.
A populated evaluation board is available upon request.
The SKY65013 is a general-purpose, broadband amplifier
fabricated from Skyworks InGaP HBT process and packaged in
a plastic Micro-X package. The amplifier’s input and output
impedances are 50 Ω, which allows these amplifiers to be
cascaded without external impedance matching networks. The
typical -3 dB bandwidth of the SKY65013 is DC–4 GHz.
Full scattering parameters for this part are available for download
at www.skyworksinc.com
This amplifier is also available in the miniature SC-88 package
(SKY65013-92LF) and the SOT-89 package (SKY65013-70LF).
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200310 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 7, 2006
1
DATA SHEET • SKY65013-214LF
Electrical Specifications at 25 °C
T = 25 °C, I = 40 mA, P = 0 dBm, Z = 50 Ω, measured in evaluation board, unless otherwise noted
C
IN
0
Parameter
Symbol
Condition
Frequency
Min.
Typ.
11.5
4
Max.
Unit
dB
Small signal gain
GP
1 GHz
10.5
3 dB gain bandwidth
Noise figure
BW
3 dB
GHz
dB
NF
2 GHz
2 GHz
5.4
12.5
1.9:1
29
Output power at 1 dB compression
Input and output VSWR
Output third order intercept point
Operating voltage
0P
11.5
3.3
dBm
1 dB
VSWR
OIP3
0.1–8 GHz
2 GHz
2.0:1
3.7
P
IN
= 0 dBm each tone, ∆f = 10 MHz
dBm
V
V
Measured at pin 3
3.5
17
D
Reverse isolation
|s
12
|
0.1–6 GHz
dB
Gain flatness
10 MHz–4 GHz
1.5
100
dB
Thermal resistance
θ
JC
°C/W
Typical Performance Data
Z = 50 Ω, IC = 40 mA, measured in evaluation board, unless otherwise noted
0
15
10
5
0
-5
-40 °C
-10
-15
-20
25 °C
85 °C
85 °C
25 °C
1
-40 °C
5
0
0
1
2
3
4
5
6
7
8
0
2
3
4
6
7
8
Frequency (GHz)
Frequency (GHz)
Gain vs. Frequency
Isolation vs. Frequency
0
-5
0
-10
-20
-30
-40
85 °C
-10
-15
-20
-25
-30
85 °C
-40 °C
25 °C
25 °C
-40 °C
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
Frequency (GHz)
Frequency (GHz)
Input Return Loss vs. Frequency
Output Return Loss vs. Frequency
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
April 7, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200310 Rev. C
2
DATA SHEET • SKY65013-214LF
Absolute Maximum Ratings
Pin Out (Top View)
4
Characteristic
RF input power
Value
15 dBm
Supply voltage
5 V
Supply current
120 mA
3
1
Power dissipation @ T = 25 °C
Operating temperature
Storage temperature
600 mW
-40 °C to +85 °C
-65 °C to +125 °C
Performance is guaranteed only under the conditions listed in the specifications table and is
not guaranteed under the full range(s) described by the Absolute Maximum specifications.
Exceeding any of the absolute maximum/minimum specifications may result in permanent
damage to the device and will void the warranty.
2
CAUTION: Although this device is designed to be as robust as
possible, ESD (Electrostatic Discharge) can damage
this device. This device must be protected at all times
from ESD. Static charges may easily produce poten-
tials of several kilovolts on the human body or
equipment, which can discharge without detection.
Industry-standard ESD precautions must be employed
at all times.
Pin Descriptions
Pin Number
Pin Name
Description
2, 4
GND
Equipotential point – Internal circuit com-
mon, which must be connected to the PCB
ground or common via the lowest possible
impedance.
1
3
Input
RF input – RF input with 50 Ω nominal
input impedance. An internally generated
DC voltage is present at this pin, so an
external DC block should be used to
connect this pin to the external circuit.
Micro-X
Output
RF output – DC supply voltage input and
RF output with 50 Ω nominal output
impedance. The nominal voltage required
at this pin is listed in the Electrical
Specifications Table. Supply current is
determined by an external resistor
connected between the DC power supply
and this pin.
0.020 (0.51 mm)
0.100 (2.54 mm)
0.020 (0.51 mm)
0.092 (2.34 mm)
0.085 (2.16 mm)
Recommended Solder Reflow Profiles
Refer to the “Recommended Solder Reflow Profile”
Application Note.
0.026 (0.660 mm)
0.060 (1.52 mm)
Tape and Reel Information
Refer to the “Discrete Devices and IC Switch/Attenuators
Tape and Reel Package Orientation” Application Note.
0.006 (0.15 mm)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200310 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 7, 2006
3
DATA SHEET • SKY65013-214LF
Evaluation Board
The SKY65013 evaluation board comprises the SKY65013
amplifier, the input and output of which are connected via 50 Ω
microstrip transmission lines with DC blocking capacitors, C and
IS
VS
1
L2
C , to the input and output SMA connectors, respectively.
2
C4
L3
R1
The positive supply voltage, V , is connected to pin 3, RF output
S
of the amplifier via the decoupling network, which consists of C ,
4
L , L and R . The power supply current, I , must be limited,
1
2
1
S
either via the current limit function of an external bench power
supply, or by replacing L with resistor R , the value of which is
given in the Current Limiting Resistor Values Table. The evaluation
L1
3
1
VD
Input
Output
board is shipped with L in place, which shifts an in-band series
3
C1
C2
resonance of the supply decoupling network out of band. For low
frequency applications, R may be used to conveniently limit
1
supply current on the evaluation board.
The evaluation board also contains a probe fixture, which
facilitates the direct measurement of the s parameters of the
SKY65015. The probe fixture comprises a very short coplanar
waveguide (CPW) transmission line to pin 1 and an identical line
to pin 3. All other pins of the amplifier are grounded. The CPW
transmission lines are compatible with ground-signal-ground
wafer probe tips, which can be connected to the RF ports of a
vector network analyzer (VNA) via coaxial cables. The very small
electrical length of these CPW transmission lines obviates the
need to de-embed their effects from the s parameters that are
measured. The supply constant current must be applied via the
bias tee, which is typically integrated into the VNA, which is
cascade with the output pin of the amplifier.
Evaluation Board Parts List
Component
Description
Capacitor
Inductor
Value
Size
0603
0603
Suggested Part Number
Comments
C , C , C
47 nF
33 nH
1
2
1
2
4
L
L
Ferrite bead
Resistor
FBMH4525HM162N-T
SKY65013
R
1
See Current Limiting
Resistor Values Table
0603
U
1
Amplifier
Current Limiting Resistor Values
R
1
Minimum Power
V , V
S
Resistance, Ω
Dissipation Rating, mW
4
4.6
5
13
28
125
125
125
250
500
500
500
1000
38
6
63
8
113
138
163
213
9
10
12
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
April 7, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200310 Rev. C
4
DATA SHEET • SKY65013-214LF
Copyright © 2002, 2003, 2004, 2005, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided
by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and
Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and
names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are
incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200310 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • April 7, 2006
5
相关型号:
©2020 ICPDF网 联系我们和版权申明