SKY73070-11 [SKYWORKS]
Double Balanced Mixer, 700MHz Min, 1000MHz Max, 5 X 5 MM, ROHS COMPLIANT, MCM, 20 PIN;型号: | SKY73070-11 |
厂家: | SKYWORKS SOLUTIONS INC. |
描述: | Double Balanced Mixer, 700MHz Min, 1000MHz Max, 5 X 5 MM, ROHS COMPLIANT, MCM, 20 PIN 局域网 射频 微波 |
文件: | 总13页 (文件大小:221K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
SKY73070: 700 – 1000 MHz High Gain and Linearity Single
Downconversion Mixer
Applications
Description
The SKY73070 is a fully integrated single mixer that includes a
Local Oscillator (LO) driver, high linearity mixer, and large
dynamic range Intermediate Frequency (IF) amplifier. A low loss
RF balun has also been included to reduce design complications
and lower system cost.
• 2G/3G base station transceivers:
− GSM/EDGE, CDMA, UMTS/WCDMA, iDEN
• Land mobile radio
• ISM band transceivers
• High performance radio links
• RF identification
The SKY73070 features an input IP3 of +27.0 dBm and a Noise
Figure (NF) of 8.3 dB, making the device an ideal solution for high
dynamic range systems such as 2G/3G base station transceivers.
The SKY73070 is manufactured using a robust silicon BiCMOS
process and has been designed for optimum long-term reliability.
The SKY73070 single downconversion mixer is provided in a
compact, 20-pin 5 x 5 mm Multi-Chip Module (MCM). A functional
block diagram is shown in Figure 1. The pin configuration and
package are shown in Figure 2. Signal pin assignments and
functional pin descriptions are provided in Table 1.
Features
• Operating frequency range: 700 to 1000 MHz
• IF frequency range: 40 to 300 MHz
• Conversion gain: 9.5 dB
• Input IP3: +27.0 dBm
• Output IP3: +36.5 dBm
• Noise figure: 8.3 dB
• Integrated LO driver
• Integrated low loss RF balun
• High linearity IF amplifier
• Small, MCM (20-pin, 5 x 5 mm) Pb-free package (MSL3, 260 °C
per JEDEC J-STD-020)
Skyworks offers lead (Pb)-free RoHS (Restriction of
Hazardous Substances) compliant packaging.
RF
LO
S1080
VCC1_LO
Figure 1. SKY73070 Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
1
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
20
19
18
17
16
1
15
14
13
12
11
VCC_IFRF
N/C
2
GND
GND
RF
3
N/C
4
GND
N/C
LO
GND
5
6
7
8
9
10
S1081
Figure 2. SKY73070 Pinout – 20-Pin MCM
Table 1. SKY73070 Signal Descriptions
Pin #
Name
VCC_IFRF
Description
Pin #
11
12
13
14
15
16
17
18
19
20
Name
Description
1
2
IF and RF DC supply, +5V
RF input
LO
LO input
RF
N/C
GND
GND
N/C
N/C
GND
IF–
No connection
Ground
3
N/C
No connection
Ground
4
GND
Ground
5
GND
Ground
No connection
No connection
Ground
6
VCC1_LO
N/C
DC supply for LO driver, +5V
No connection
DC supply for LO buffer, +5V
No connection
Ground
7
8
VCC2_LO
N/C
Negative IF output
Positive IF output
IF bias adjust
9
IF+
10
GND
RXIF
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
January 21, 2008 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200716F
2
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
injection. However, the LO can be driven over a wide frequency
range with only slight degradation in performance.
Functional Description
The SKY73070 is a high gain single mixer, optimized for base
station receiver applications. The device consists of a low loss RF
balun, high linearity passive mixer, and a low noise IF amplifier.
IF Amplifier
An LO amplifier is also included that allow the SKY73070 to
connect directly to the output of a Voltage Controlled Oscillator
(VCO). This eliminates the extra gain stages needed by most
discrete passive mixers.
The SKY73070 includes a high dynamic range IF amplifier that
follows the passive mixer in the signal path. The outputs require a
supply voltage connection using inductive chokes. These choke
inductors should be high-Q and have the ability to handle 200 mA
or greater.
RF Balun and Passive Mixer
A simple matching network allows the output ports to be matched
to a balanced 200 Ω impedance. The IF amplifier is optimized for
IF frequencies between 40 and 300 MHz. The IF amplifier can be
operated outside of this range, but with a slight degradation in
performance.
The RF balun provides a single ended input, which can easily be
matched to 50 Ω using a simple external matching circuit. The RF
balun offers very low loss, and excellent amplitude and phase
balance.
The high linearity SKY73070 is a passive, double balanced mixer
that provides a very low conversion loss, and excellent 3rd Order
Input Insertion Point (IIP3).
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY73070 are provided in
Table 2 and the recommended operating conditions in Table 3.
Electrical characteristics for the SKY73070 are provided in
Table 4.
Additionally, the balanced nature of the mixer provides for high
port-to-port isolation.
LO Buffer
Typical performance characteristics for the SKY73070 are
illustrated in Figures 3 through 18.
An LO buffer allows the input power of the SKY73070 to be in the
range of ±6 dBm. The LO section is optimized for high-side LO
Table 2. SKY73070 Absolute Maximum Ratings (Note 1)
Parameter
Supply voltage, +5 V
Symbol
Minimum
Maximum
5.5
Units
V
VCC
ICC
4.5
Supply current
240
mA
dBm
dBm
°C
RF input power
PRF
PLO
TC
+20.0
+20.0
+85
LO input power
Operating case temperature
Junction temperature (Note 2)
Storage case temperature
–40
–40
TJ
+150
+125
°C
TSTG
°C
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value.
Note 2: Nominal thermal resistance (junction to center ground pad) is 5.1 °C/W.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
3
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
Table 3. SKY73070 Recommended Operating Conditions
Parameter
Supply voltage, +5 V
Symbol
Minimum
Typical
5.00
210
Maximum
Units
V
VCC
ICC
4.75
5.25
Supply current
mA
LO input power
PLO
TC
–6.0
–40
700
900
40
0
+6.0
+85
dBm
°C
Operating case temperature
RF frequency range
LO frequency range (Note 1)
IF frequency range
fRF
1000
1250
300
MHz
MHz
MHz
FLO
FIF
Note 1: The SKY73070 has been optimized for high-side LO injection. However, the LO can be used outside of the specified frequency range with degraded performance.
Table 4. SKY73070 Electrical Specifications
(VCC = +5 V, TA = +25 °C, LO = 0 dBm, RF Frequency = 900 MHz, IF Frequency = 200 MHz, LO Frequency = 1100 MHz, Unless Otherwise
Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Conversion gain
G
fRF = 824 to 915 MHz,
TA = 25 °C, PLO = –3 to
+3 dBm
8.2
9.5
dB
Gain variation over temperature
Noise Figure
TA = –40 to +85 °C
0.6
8.3
dB
dB
NF
TA = 25 °C, PLO = –3 to
+3 dBm, VCC = 4.75 to
5.25 V, IF = 200 MHz
Noise Figure variation over temperature
Noise Figure with a blocker signal
TA = –40 to +85 °C
0.8
18
dB
dB
NFBLK
IIP3
Blocking signal input
power = +8 dBm
Third order input intercept point
fRF = 900 MHz and
900.8 MHz,
+24.7
+27.0
dBm
PRF = –10 dBm/tone,
VCC = 4.75 to 5.25 V
Input IP3 variation over temperature
Third order output intercept point
TA = –40 to +85 °C
0.3
dB
OIP3
fRF = 900 MHz and
900.8 MHz,
+36.5
dBm
PRF = –10 dBm/tone,
VCC = 4.75 to 5.25 V
2RF – 2LO
2x2
PRF = –10 dBm
PRF = –10 dBm
–68.5
–80
–63
–70
dBc
dBc
dBm
dBm
dB
3RF – 3LO
3x3
Input 1 dB compression point
Output 1 dB compression point
RF to IF isolation
IP1dB
OP1dB
+11.0
30
+13.3
+22.8
48
LO leakage:
@ RF port
@ IF port
–59
–34
–20
–23
dBm
dBm
RF port input return loss
LO port input return loss
IF port output return loss
ZIN_RF
ZIN_LO
ZOUT_IF
With external matching
components
14
14
14
dB
dB
dB
With external matching
components
With external matching
components
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
January 21, 2008 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200716F
4
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
11.0
10.5
10.0
9.5
11.0
10.5
10.0
9.5
4.75 V
5.00 V
5.25 V
9.0
9.0
8.5
8.5
8.0
8.0
7.5
7.5
o
o
o
–40
+25
+85
C
C
C
7.0
7.0
6.5
6.5
6.0
6.0
824
824
824
839
854
869
884
899
914
914
914
824
839
854
869
884
899
914
914
914
RF Frequency (MHz)
RF Frequency (MHz)
Figure 3. Gain vs Frequency and Supply Voltage
Figure 4. Gain vs Frequency and Temperature
11.0
10.5
10.0
9.5
14
13
12
11
10
9
o
–3 dBm
0 dBm
–40
+25
+85
C
o
o
C
C
+3 dBm
9.0
8.5
8.0
8
7.5
7
7.0
6
6.5
5
6.0
4
839
854
869
884
899
824
839
854
869
884
899
RF Frequency (MHz)
RF Frequency (MHz)
Figure 5. Gain vs Frequency and LO Power
Figure 6. Noise Figure vs Frequency and Temperature
14
13
12
11
10
9
14
13
12
11
10
9
4.75 V
5.00 V
5.25 V
–3 dBm
0 dBm
+3 dBm
8
8
7
7
6
6
5
5
4
4
839
854
869
884
899
824
839
854
869
884
899
RF Frequency (MHz)
RF Frequency (MHz)
Figure 7. Noise Figure vs Frequency and Supply Voltage
Figure 8. Noise Figure vs Frequency and LO Power
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
5
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
30
29
28
27
26
25
24
23
22
21
20
30
29
28
27
26
25
24
23
22
21
20
o
o
o
4.75 V
5.00 V
5.25 V
–40
+25
+85
C
C
C
824
824
824
839
854
869
884
899
914
914
914
824
824
824
839
854
869
884
899
914
914
914
RF Frequency (MHz)
RF Frequency (MHz)
Figure 9. IIP3 vs Frequency and Temperature
Figure 10. IIP3 vs Frequency and Supply Voltage
30
29
28
27
26
25
24
23
22
21
20
18
17
16
15
14
13
12
11
10
9
o
o
o
–3 dBm
0 dBm
+3 dBm
–40
+25
+85
C
C
C
8
839
854
869
884
899
839
854
869
884
899
RF Frequency (MHz)
RF Frequency (MHz)
Figure 11. IIP3 vs Frequency and LO Power
Figure 12. IP1dB vs Frequency and Temperature
18
17
16
15
14
13
12
11
10
9
18
17
16
15
14
13
12
11
10
9
4.75 V
5.00 V
5.25 V
–3 dBm
0 dBm
+3 dBm
8
8
839
854
869
884
899
839
854
869
884
899
RF Frequency (MHz)
RF Frequency (MHz)
Figure 13. IP1dB vs Frequency and Supply Voltage
Figure 14. IP1dB vs Frequency and LO Power
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
January 21, 2008 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200716F
6
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
–55
–59
–63
–67
–71
–75
–79
–83
–87
–91
–95
55
53
51
49
47
45
43
41
39
37
35
o
o
o
o
o
o
–40
+25
+85
C
C
C
–40
+25
+85
C
C
C
824
839
854
869
884
899
914
824
839
854
869
884
899
914
RF Frequency (MHz)
RF Frequency (MHz)
Figure 15. 2RF – 2LO vs Frequency and Temperature
Figure 16. RF to IF Isolation vs Frequency and Temperature
–25
–27
–29
–31
–33
–35
–37
–39
–41
–43
–45
–30
o
o
o
o
–40
+25
+85
C
–40
+25
+85
C
C
C
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
o
o
C
C
824
839
854
869
884
899
914
824
839
854
869
884
899
914
RF Frequency (MHz)
RF Frequency (MHz)
Figure 17. LO to IF Leakage vs Frequency and Temperature
Figure 18. LO to RF Leakage vs Frequency and Temperature
to the Package and Handling Information section of this Data
Sheet.
Evaluation Board Description
The SKY73070 Evaluation Board is used to test the performance
of the SKY73070 downconversion mixer. An assembly drawing for
the Evaluation Board is shown in Figure 19 and the layer detail is
provided in Figure 20.
3. Skyworks recommends including external bypass capacitors
on the VCC voltage inputs of the device.
4. Components L5 and L4 (see Figure 21) are high-Q, low loss
inductors. These inductors must be able to pass currents in
excess of 200 mA DC.
Circuit Design Configurations
The following design considerations are general in nature and
must be followed regardless of final use or configuration:
5. Components R7 and R8 (see Figure 21) allow for external
adjustment of the IF amplifier bias points. To reduce the IF
amplifier bias current, connect pin 20 to ground through
external resistor R8. To increase the IF amplifier bias current,
connect pin 20 to VCC through external resistor R7. For
operation as specified in Tables 3 and 4, these resistors are
not required.
1. Paths to ground should be made as short and as low
impedance as possible.
2. The ground pad of the SKY73070 provides critical electrical
and thermal functionality. This pad is the main thermal
conduit for heat dissipation. Since the circuit board acts as
the heat sink, it must shunt as much heat as possible from
the device. Therefore, design the connection to the ground
pad to dissipate the maximum heat produced by the circuit
board. For more information on soldering the SKY73070, refer
A schematic diagram for the SKY73070 Evaluation Board is
shown in Figure 21.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
7
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
J9
J5
C16 C15
C13 C14
L2
C18
R6
L3
C17
R5
R4
T2
C11
C12
J8
J3
R3
L5
L4
R7
R8
C19
C20
C1
C10
C7
R1
J4
U1
C2
L1
C3
C5
C6
C4
R2
C8
C9
J1
J2
Note: This Evaluation Board is used for several different Skyworks devices.
Components C4, C6, C8 through C13, C15 through C19, R3, R5, and L3 are not used for the
device described by this Data Sheet.
S1083
Figure 19. SKY73070 Evaluation Board Assembly Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
January 21, 2008 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200716F
8
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
Layer 1: Top – Metal
Layer 2: Ground
Layer 3: Power Plane
Layer 4: Solid Ground Plane
S940
Figure 20. SKY73070 Evaluation Board Layer Detail
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
9
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
R6
0 Ω
3
2
4
6
R4
0 Ω
J5
L2
8.2 nH
L4
T2
470 nH
1
C14
22 pF
L5
470 nH
VCC
R7
DNI
R8
DNI
×
20
19
18
17
16
C20
1 μF
1
15
×
VCC_IFRF
VCC
N/C
2
3
4
5
14
13
J4
RF
GND
GND
C2
15 nH
C3
2.7 pF
C1
0 Ω
R1
0 Ω
SKY73070
×
N/C
GND
GND
12
L1
R2
0 Ω
×
J3
N/C
LO
3.3 pF
11
C7
33 pF
6
7
8
9
10
×
×
VCC
C5
33 pF
Notes: Values for all components are subject to change
for matching purposes.
Some component labels may be different than the
corresponding component symbol shown here.
Component values, however, are accurate as of the
date of this Data Sheet.
S1082
Figure 21. SKY73070 Evaluation Board Schematic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
January 21, 2008 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200716F
10
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
PCB Design & SMT Assembly/Rework Guidelines for MCM-L
Packages, document number 101752.
Package Dimensions
Figure 22 shows the package dimensions for the 20-pin MCM,
and Figure 23 provides the tape and reel dimensions.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format. For packaging details, refer to the Skyworks
Application Note, Tape and Reel, document number 101568.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
Electrostatic Discharge (ESD) Sensitivity
The SKY73070 is a static-sensitive electronic device. Do not
operate or store near strong electrostatic fields. Take proper ESD
precautions.
THE SKY73070 is rated to Moisture Sensitivity Level 3 (MSL3) at
260 °C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
5X 4.8
5
B
Pin 20
Pin 1
Indicator
C
Pin 1 indicator
(See Detail B)
Pin 1
4X 1.3
4X 0.65
0
5
5X 4.8
A
20X SMT Pad
0.15 A
B C
Solder Mask Opening
A
0.2
A B C
1.1 0.1
0.15
A B C
0.1
Side View
Bottom View
Top View
Solder Mask Edges
0.2 x 0.2
Metal Pad Edge
3
0.45 0.05
0.3 0.03
(0.1)
3X R0.2
0.45 0.1
3
Detail B
Detail A
All measurements are in millimeters.
Dimensioning and tolerancing according to ASME Y14.5M-1994.
S944
Figure 22. SKY73070 20-Pin MCM Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
11
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
2.00 0.05
8.00 (P1)
4.00 (P0)
∅1.55 0.05
0.30 0.05
B
1.75 0.10
Pin #1
Indicator
A
A
5o Max.
B
∅1.50 Min.
1.70
5.35
B
5o Max.
Notes:
1. Carrier tape: black conductive polystyrene
2. Cover tape material: transparent conductive PSA
3. Cover tape size: 9.3 mm width
4. ESD surface resistivity is </=1 x 1010 Ohms/Square
according to EIA, JEDIC TNR specification.
5. P0/P1 10 pitches cumulative tolerance on tape: 0.20 mm
6. A and B measurement points are 0.30 mm from bottom pocket.
7. All dimensions are in millimeters
A
S461
Figure 23. SKY73070 Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
January 21, 2008 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200716F
12
DATA SHEET • SKY73070 DOWNCONVERSION MIXER
Ordering Information
Model Name
Manufacturing Part Number
SKY73070-11 (Pb-free package)
Evaluation Kit Part Number
SKY73070 700-1000 MHz Downconversion Mixer
TW16-D660
Copyright © 2007, 2008 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200716F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • January 21, 2008
13
相关型号:
UL1042
UL1042 - Uk砤d zr體nowa縪nego mieszacza iloczynowegoWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV201
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14
IC-SM-VIDEO AMPWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TA
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TC
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV302N16
IC-SM-4:1 MUX SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV4089
VIDEO AMPLIFIER WITH DC RESTORATIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
©2020 ICPDF网 联系我们和版权申明