SKY77166 [SKYWORKS]
Power Amplifier Module for CDMA2000 (450-460 MHz); 功率放大器模块的CDMA2000 ( 450-460兆赫)型号: | SKY77166 |
厂家: | SKYWORKS SOLUTIONS INC. |
描述: | Power Amplifier Module for CDMA2000 (450-460 MHz) |
文件: | 总9页 (文件大小:385K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ADVANCE DATA SHEET
SKY77166 Power Amplifier Module for CDMA2000
(450-460 MHz)
Applications
Description
The SKY77166 Power Amplifier Module (PAM) is a fully matched 10-pad surface mount module
developed for Code Division Multiple Access (CDMA2000) handsets and Wireless Local Loop
applications. This small and efficient module packs full coverage of the 450–460 MHz bandwidth into
a single compact package. The SKY77166 meets the stringent CDMA2000 linearity requirements to
and exceeding 29 dBm output power.
• Digital cellular (CDMA2000)
• Wireless Local Loop (WLL)
Features
• Low voltage positive bias
supply: 3.2 V to 4.2 V
The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) contains all active
circuitry within the module, which includes onboard bias circuitry as well as input and interstage
matching circuits. Output match into a 50-ohm load is realized off-chip within the module package to
optimize efficiency and power performance. This device is manufactured with Skyworks’ GaAs
Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply
operation while maintaining high efficiency and good linearity.
• Good linearity
• High efficiency across wide
dynamic range
• Dual-mode operation
• 10-pad package:
4 x 4 x 1.15 mm
Primary bias to the SKY77166 is supplied directly from a three-cell Ni-Cd, a single-cell Li-Ion, or other
suitable battery with an output in the 3.2 to 4.2 volt range. Power down is accomplished by setting the
voltage on the low current reference pin to zero volts. No external supply side switch is needed as
typical “off” leakage is a few microamperes with full primary voltage supplied from the battery.
• Power down control
• Low power state control
• CDMA2000
Skyworks offers lead
(Pb)-free, RoHS
(European Parliament
for the Restriction of
Hazardous Substances)
-compliant packaging.
Figure 1. Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200466A • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • December 6, 2007
1
ADVANCE DATA SHEET
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
Electrical Target Specifications
The following tables list the electrical characteristics of the
SKY77166 Power Amplifier. Table 1 lists the absolute maximum
ratings, while Table 2 shows the recommended operating
conditions to achieve the performance characteristics listed in
Table 4. Table 3 presents a truth table for the power settings.
Table 1. Absolute Maximum Rating 1
Parameter
Symbol
Minimum
Nominal
Maximum
Unit
RF Input Power
Supply Voltage
PIN
—
—
—
0.0
3.4
6.0
6.0
dBm
Volts
Volts
VCC
Reference Voltage
VREF
2.85
2.95
Operating TC
Storage
–30
–55
+25
—
+110
+125
2
Case Temperature
°C
TSTG
1
No damage assuming only one parameter is set at limit at a time with all other parameters set at nominal value.
2
Case Temperature refers to the temperature of the case measured at the GROUND PAD at the underside of the package.
Table 2. Recommended Operating Conditions
Parameter
Symbol
Minimum
Nominal
Maximum
Unit
Supply Voltage
VCC
3.2
3.4
4.2
Volt
Reference Voltage
VREF
2.80
2.85
2.95
Volts
HIGH
LOW
2.5
0.0
—
—
3.0
0.5
Control voltage
VCONT
Volt
Operating Frequency
FO
TC
450.0
–30
455.0
+25
460.0
+85
MHz
°C
1
Case Temperature
1
Case Temperature (TC) refers to the temperature of the case measured at the GROUND PAD at the underside of the package.
Table 3. Power Range Truth Table
Power Mode
VREF
VCONT
Range
High Power
Low Power
Shut Down
2.85 V
2.85 V
0.0 V
0.0 V – 0.5 V
2.5 V – 3.0 V
0.0 V
16 dBm – 29 dBm
≤ 16 dBm
—
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
December 6, 2007 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200466A
2
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
ADVANCE DATA SHEET
Table 4. Electrical Specifications for CDMA2000 Nominal Operating Conditions 1
Characteristics
Symbol
Condition
Minimum
Typical
Maximum
Unit
VCONT ≥ 2.5 V
PO = 16 dBm
GLOW
24.5
26.5
28.2
Gain conditions
dB
VCONT ≤ 0.5 V
PO = 29 dBm
GHIGH
29.0
6.5
30.0
7.0
32.0
—
VCONT ≥ 2.5 V
PO = 16 dBm
PAELOW
PAEHIGH
Power Added Efficiency
%
VCONT ≤ 0.5 V
PO = 29 dBm
33.0
37.0
—
ICC_LOW
ICC_HIGH
IQ_LOW
IQ_HIGH
IREF
PO = 16 dBm
PO = 29 dBm
VCONT ≥ 2.5 V
VCONT ≤ 0.5 V
—
—
—
—
—
—
165
630
75
180
695
—
Total Supply current
Quiescent current
mA
mA
95
—
Reference current
Control current
—
0.75
0.95
1.0
1.2
mA
mA
ICONT
VCONT = 2.5 V
VCC = 3.4 V
VREF = 0 V
Total Supply current in Power-down Mode
IPD
—
2.0
4.5
μA
885 kHz offset
ACP1
—
—
–50.0
–61.0
–50.0
–60.0
–130
4.0
–47.5
–60.0
–45.0
–55.0
–128
5.5
2,3,4
Adjacent Channel Power
PO ≤ 29 dBm
dBc
1.98 MHz offset ACP2
Second
Third
f02
—
Harmonic Suppression
PO ≤ 29 dBm
PO ≤ 29 dBm
dBc
f03
—
Noise Power in RX Band 460-470 MHz
Noise Figure
RXBN
NF
—
dBm/Hz
dB
—
—
Input Voltage Standing Wave Ratio (VSWR)
Stability (Spurious output)
VSWR
S
—
5:1 VSWR All phases
PO ≤ 29 dBm
—
1.6:1
—
1.8:1
–70
—
—
dBc
5
Ruggedness
Ru
10:1
—
—
VSWR
1
Unless specified otherwise:
VCC = +3.4 V
VREF = +2.85 V
Temp = +25 °C
2
ACP is specified per CDMA2000 as the ratio of the total in-band power (1.23 MHz) to adjacent power in a 30 kHz BW.
3
4
5
CDMA2000 is configured as FCH = 9600 or PCH = –3.75 dB, DCCH = 9600, –7.0 dB, SCH = 9600, SCH = 9600, –5.36 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB.
For operation at VCC = 3.2 V, POUT is derated by 0.25 dB
All phases, time = 10 seconds.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200466A • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • December 6, 2007
3
ADVANCE DATA SHEET
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
Evaluation Board Description
The evaluation board is a platform for testing and interfacing
design circuitry. To accommodate the interface testing of the
SKY77166, the evaluation board schematic and diagram are
included for preliminary analysis and design. Figure 2 shows the
basic schematic of the board for the 450 MHz to 460 MHz range
and Figure 3 is the assembly diagram.
Figure 2. Evaluation Board Schematic
Figure 3. Evaluation Board Assembly Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
December 6, 2007 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200466A
4
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
ADVANCE DATA SHEET
Package Dimensions and Pad Descriptions
The SKY77166 is a multi-layer laminate base, overmold
pad function and the pad numbering convention, which starts
with pad 1 in the upper left and increments counter-clockwise
around the package. Figure 7 illustrates typical case markings.
encapsulated modular package designed for surface mount solder
attachment to a printed circuit board. Figure 4 is a mechanical
drawing of the pad layout for this package. Figure 6 shows each
Figure 4. Dimensional Drawing – 4 x 4 x 1.15 mm, 10-Pad Package – SKY77166
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200466A • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • December 6, 2007
5
ADVANCE DATA SHEET
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
Figure 5. Phone PCB Layout Footprint for 4 x 4 mm, 10-Pad Package – SKY77166 Specific
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
December 6, 2007 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200466A
6
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
ADVANCE DATA SHEET
procedures recommended by Skyworks, please refer to Skyworks
Application Note: PCB Design and SMT Assembly/Rework,
Document Number 101752. Additional information on standard
SMT reflow profiles can also be found in the JEDEC Standard
J-STD-020.
Production quantities of this product are shipped in the standard
tape-and-reel format. For packaging details, refer to Skyworks
Application Note: Tape and Reel Information – RF Modules,
Document Number 101568.
Electrostatic Discharge Sensitivity
The SKY77166 is a Class 2 device. Figure 8 lists the Electrostatic
Discharge (ESD) immunity level for each non-ground pad of the
SKY77166 product. The numbers in Figure 8 specify the ESD
threshold level for each pad where the I-V curve between the pad
and ground starts to show degradation.
Figure 6. Pad Names and Configuration (Top View)
The ESD testing was performed in compliance with MIL-STD-
883E Method 3015.7 using the Human Body Model. If ESD
damage threshold magnitude is found to consistently exceed
2000 volts on a given pad, this so is indicated. If ESD damage
threshold below 2000 volts is measured for either polarity,
numbers are indicated that represent worst case values observed
in product characterization.
Various failure criteria can be utilized when performing ESD
testing. Many vendors employ relaxed ESD failure standards,
which fail devices only after “the pad fails the electrical
specification limits” or “the pad becomes completely
non-functional”. Skyworks employs most stringent criteria and
fails devices as soon as the pad begins to show any degradation
on a curve tracer.
Figure 7. Typical Case Markings – 4 x 4 mm Package
Package and Handling Information
Because of its sensitivity to moisture absorption, this device
package is baked and vacuum-packed prior to shipment.
Instructions on the shipping container label must be followed
regarding exposure to moisture after the container seal is broken,
otherwise, problems related to moisture absorption may occur
when the part is subjected to high temperature during solder
assembly.
The SKY77166 is capable of withstanding an MSL3/250 °C solder
reflow. Care must be taken when attaching this product, whether
it is done manually or in a production solder reflow environment.
If the part is attached in a reflow oven, the temperature ramp rate
should not exceed 3 °C per second; maximum temperature
should not exceed 250 °C. If the part is manually attached,
precaution should be taken to insure that the part is not subjected
to temperatures exceeding 250 °C for more than 10 seconds. For
details on attachment techniques, precautions, and handling
Figure 8. ESD Sensitivity of Non-Ground Pads (Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
200466A • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • December 6, 2007
7
ADVANCE DATA SHEET
SKY77166 POWER AMPLIFIER MODULE FOR CDMA2000 (450-460 MHZ)
To avoid ESD damage, both latent and visible, it is very important
that the product assembly and test areas follow the Class-1 ESD
handling precautions listed below.
• Personnel Grounding
• Facility
- Wrist Straps
- Conductive Smocks, Gloves and Finger Cots
- Antistatic ID Badges
- Relative Humidity Control and Air Ionizers
- Dissipative Floors (less than 109 Ω to GND)
• Protective Workstation
• Protective Packaging and Transportation
- Dissipative Table Top
- Bags and Pouches (Faraday Shield)
- Protective Tote Boxes (Conductive Static Shielding)
- Protective Trays
- Grounded Carts
- Protective Work Order Holders
- Protective Test Equipment (Properly Grounded)
- Grounded Tip Soldering Irons
- Solder Conductive Suckers
- Static Sensors
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
December 6, 2007 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200466A
8
Ordering Information
Model Number
Manufacturing Part Number
Product Revision
Package
Operating Temperature
SKY77166
SKY77166
MCM 4x4
–30 °C to +85 °C
Revision History
Revision
Level
Date
Description
P1
A
September 22, 2006 Advance Information
February 15, 2007 Revise: Change data sheet Revision suffix from P1 to A (Advance data sheet status continues); Table 4
December 6, 2007 Revise: Figures 1, 2, 3, 6–8; Table 4
B
References
Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752
Application Note: Tape and Reel Information – RF Modules, Document Number 101568
Standard SMT Reflow Profiles: JEDEC Standard J–STD–020 (current revision).
Copyright © 2005–2007, Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products. These materials are provided by Skyworks as a service to its customers and may be
used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products,
specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts,
incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of
Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions.
THESE MATERIALS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS
INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER
INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST
REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their
own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
The following are trademarks of Skyworks Solutions, Inc.: Skyworks®, the Skyworks logo, and Breakthrough Simplicity®. Product names or services listed in this publication are for identification
purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at
www.skyworksinc.com, is incorporated by reference.
相关型号:
UL1042
UL1042 - Uk砤d zr體nowa縪nego mieszacza iloczynowegoWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV201
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14
IC-SM-VIDEO AMPWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TA
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TC
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV302N16
IC-SM-4:1 MUX SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV4089
VIDEO AMPLIFIER WITH DC RESTORATIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
©2020 ICPDF网 联系我们和版权申明