LE200S-CD [SLPOWER]
200W Single Output LED Driver Series; 200W单路输出LED驱动器系列型号: | LE200S-CD |
厂家: | SL Power Electronics |
描述: | 200W Single Output LED Driver Series |
文件: | 总4页 (文件大小:1106K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LE200S-CD
200W Single Output
LED Driver Series
Features
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
High Efficiency (up to 93%)
Wide Range Universal Input 90-305 VAC
Active Power Factor Correction (0.99 typical)
Constant Current Output
Dimming Function
Lightning Protection
Waterproof (IP67)
Overcurrent, Overvoltage, Overtemperature
Protection
ꢀ
ꢀ
Meets UL8750 & EN61347 Safety
3 Year Warranty
Description
The LE200S-CD Series operate from a 90 ~ 305Vac input range. These units will provide up to a 0.7A of
output current and a maximum output voltage of 285Vdc for 200 W maximum output power. They are designed
to be highly efficient and highly reliable. The standard features include dimming control, lightning protection,
over voltage protection, short circuit protection, and over temperature protection.
Model Selection
Model
Number
Output
Current
Output
Voltage
Efficiency*
Ripple &
Noise**
Regulation
Line
Overvoltage
Trip Level
110Vac
220Vac
Load
LE200S70CD
665mA-735mA
143V – 285V
90%-91%
92%-93%
8.6V pk-pk max.
342V – 428V
1%
3%
Notes:
1. Efficiency measured at full load, at input voltage noted.
2. Measured at 20MHz bandwidth, with noise probe directly across output terminals, and load terminated with 0.1µF ceramic and 10µF low ESR electrolytic
capacitors.
General Specifications
1.0 seconds, max.
Constant Current
AC Input 90-305Vac, 47-63Hz, 1∅
Turn On Time
Overload
Protection
100Vac: 2.4A, 220Vac: 1.2A
Input Current
Inrush Current
Input Fuses
Dimming
Function
1-10Vdc source or External Resistor can be
used for dimming control. See below.
230Vac, cold start: will not exceed 65A
XA, 250VAC fuses provided on all models
www.slpower.com
LE200S-CD REV 2.0,11-FEB-13
1
LE200S-CD
200W Single Output
LED Driver Series
General Specifications (continued)
Earth Leakage
<0.75mA@277Vac, 50Hz
Current
Short Circuit
Protection
Provided - no damage to unit, self-recovery.
Latch mode. AC input will need to be reset to
return to normal operation after an OVP
condition. See chart for trip range.
Overvoltage
Protection
See Models chart.
200W continuous
See chart
Efficiency
Output Power
Ripple and Noise
Output Voltage
Total Regulation
Dimensions
Latch mode. AC input will need to be reset to
return to normal operation after an OTP
condition. Trip Temperature = 110°C typical.
Overtemperature
Protection
Operating
Temperature
Operating: -35°C to +70°C
Non-operating: -40°C to +85°C
10% to 100% operating
5% to 100%, non-operating
See chart
Relative Humidity
Safety Standards
MTBF
UL8750, UL935, UL1012, CSA-C22.2 No. 107.1,
EN61347-1, EN61347-2-13
+/- 3%. See chart
W: 3.13” x L: 9.37” x H: 1.81”
1500g
330,000 hours (450mA model, 110Vac input,
80% load, 25°C ambient, per MIL-HDBK-217F).
90,000 hours (1400mA model, at 110Vac input,
80% load, 45°C ambient temperature).
Weight
Lifetime
EMI/EMC Compliance
EN55015, Radiated & Conducted with 6db of margin
Emissions
EN61547
EMI for Lighting Equipment
Static Discharge Immunity
Radiated RF Immunity
EFT/Burst Immunity
EN61000-4-2, 4kV Contact Discharge, 8kV air discharge
EN61000-4-3
EN61000-4-4
EN61000-4-5, 4kV line-line, 6kV line-earth
EN61000-4-6
Line Surge Immunity
Conducted RF Immunity
Power Frequency Magnetic Field Immunity
Voltage Dip Immunity
EN61000-4-8
EN61000-4-11
EN61000-3-2
Line Harmonic Emissions
Flicker Test
EN61000-3-3
www.slpower.com
LE200S-CD REV 2.0,11-FEB-13
2
LE200S-CD
200W Single Output
LED Driver Series
Derating Curves
Mechanical Drawing
www.slpower.com
LE200S-CD REV 2.0,11-FEB-13
3
LE200S-CD
200W Single Output
LED Driver Series
Dimming Control
The dimmer control may be operated from either a potentiometer or from an input signal of 1 – 10 Vdc. Two recommended implementations are
provided below.
Parameters:
Parameter
Min.
-2V
0mA
Typ.
Max.
Notes
Absolute Max. Voltage on the 1-10V input
-
-
12V
Sink Current on the 1-10V input pin
1mA
LE200SXXXCD
Dimming Configuration using External Voltage
Dimming Configuration using External Resistance
Dimming Control Notes:
1. Io is actual output current and Ir is rated current without dimming control.
2. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 50% of the max.
output voltage for any given model).
3. If the output voltage is maintained above 50% of the maximum output voltage, the dimming control may be
operated over the entire 1-10V range with output current varying from 100% down to practically 10%.
4. The dimming signal is allowed to be less than 1V, however, when it for 0-1V, the output current is 10%Io.
5. Do not connect the GND of dimming to the output; otherwise, the LED driver can not work normally.
Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for
consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.
www.slpower.com
LE200S-CD REV 2.0,11-FEB-13
4
相关型号:
©2020 ICPDF网 联系我们和版权申明