TCM-1000-48 [SLPOWER]
1000 WATTS POWER FACTOR CORRECTED POWER FACTOR CORRECTED;
| 型号： | TCM-1000-48 |
| 厂家： | 
SL Power Electronics |
| 描述： | 1000 WATTS POWER FACTOR CORRECTED POWER FACTOR CORRECTED |
| 文件： | 总2页 (文件大小：125K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
1 0 0 0 WATTS
P OWER FACTOR CORRECTED
S INGLE OUTP UT, HOT S WAP
TCM-1000
Featuring:
STANDARD TCM SERIES
• Diode isolated output for hot swap
MODEL
OUTPUT RATING
PWR OUT
• “Zero wire” slope program current
TCM-1000-24
TCM-1000-28
TCM-1000-48
24V @ 41.6A
28V @ 35.7A
48V @ 20.8A
1000
1000
1000
sharing
• High power density 6.5 Watt/cu. in.
• Industry standard DIN connector
• 0.99 typical power factor
The 1000-watt TCM Series “hot swap-
pable” power supplies deliver remarkable
economy and reliability in applications
that require redundancy over extended
temperature ranges. These high-density,
single-output supplies are available
with a front panel and handle for use in
sub-system racks or without handles
for embedded applications.
Power factor correction, OR-ing diodes,
and current sharing make the TCM
Series an ideal choice for communica-
tions and data processing systems
utilizing distributed power or redundant
power architecture.
• DC power good and AC power
fail signals
• True remote inhibit
• Monotonic turn-on and turn-off
• Extended temperature operation
• High efficiency 87% typical
(48 V units)
• Operating temperature range
-20°C to +60°C
Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com
1 0 0 0 WATTS
1 3 .2 7 ” x 4 .8 7 ” x 2 .4 9 ”
TCM-1 0 0 0
TCM-1000
5.2 lbs - 2.6 kgs
Dimensions:
Inches
Millimeters
ENVIRONMENTAL
SPECIFICATIONS: ALL MODELS
Thermal Protection: Shuts down power supply if overheated. Automatic recovery.
Temperature Range: -20° to +60° C, full power, de-rate to 66% maximum power @ 71° C.
Safety Agencies: Approved to UL1950; CSA 22.2 #950; IEC 950 and TUV EN60950,
Class 1 SELV, CE 73/23/EEC//93/68/EEC (low voltage directive).
Conducted RFI: Meets FCC Part 15, Subpart J, Class A; EN55022 Class B;
and CISPR 22 Class B.
INPUT
AC Input: 180-264 Vac, 47-63 Hz internally fused 10 A.
Power Factor: 0.99 typical at full load. Meets EN61000-3.2.
Inrush: Limited by thermistor, 40 Ampere maximum (8ms), cold start.
Hold Up Time: 20 ms minimum after removal of power supply at full load.
Efficiency: 87% typical @ full load.
Output Isolation: Isolated from ground 100 Vdc.
AC Power Fail: Provides TTL "O" 5 ms before output voltage goes out of regulation
band upon loss of AC power.
Cooling: Self-cooled by internal ball-bearing fan.
OUTPUT
OPTIONS
Adjustability: User adjustable ±5% minimum.
Output: 48 V @ 20.8 Amp. (1000 W max.).
Line Regulation: ±0.2%
Option "R" - Rack Mount Panel: special panel that is required for rack mounting.
Consult factory for other available options.
Load Regulation: ±2% (Slope Program) from 0 to 100% load changes.
Turn On Delay: 1 second typical.
Ripple & Noise: 0.5% p-p, measured at 20 MHz bandwidth.
Temperature Coefficient: 0.02% per degree C.
AC INPUT (180-264 VAC Continuous Range)
Stability: 0.1% over 8 hours, under constant line, load and ambient.
Transient Response: Output voltage returns to within 1% in less than 500 µs for a
50% load change. Peak transient does not exceed 3%.
Overload Protection: Electronic current limit, 120% maximum.
Overvoltage Protection: Protects load against power supply induced overvoltage.
Trip point is factory set so that output voltage cannot exceed 136% of nominal.
Requires AC input to be cycled to reset.
Remote Inhibit: Contact closure or TTL "0" turns off output.
DC Power Good: Provides a TTL "0" open collector when output is above 90% of
nominal Maximum pull-up voltage 30 Vdc; maximum sink current, 10 mA.
Redundancy: Built-in OR-ing diode, slope program current sharing, and DIN blade
connector provide "hot swap" and "N+1" capabilities. Current sharing remains
within 10% of the unit's full output rating given 0.2% initial accuracy in the
output voltage setting.
LOCATION
230 VAC
CONNECTOR
Z32
D30
Z28
Line 1
Eurocard Connector -
Male DIN 41 612
Level 1- Type H
Line 2
Safety Ground
DC OUTPUT
FUNCTION
Output
LOCATION
NOTES
CONNECTOR
Eurocard Connector -
Male DIN 41 612
Level 1- Type H
Z12 D14 Z16 D18
Z4 D6 Z8 D10
(+) Polarity
(-) Polarity
Voltage
Current Sharing: As calibrated at factory, modules will share current within
10% of full rated load.
Reverse Voltage: Protected against reverse voltage up to twice output voltage rating.
(internal OR-ing diode.)
STATUS AND CONTROL
FUNCTION
DC Power Good
AC Power Fail
Inhibit
LOCATION
NOTES
CONNECTOR
Eurocard Connector -
Male DIN 41 612
Level 1- Type H
Z20
D22
Z24
Reference to
Common
Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com
相关型号：
©2020 ICPDF网 联系我们和版权申明