SM9233 [SMI]
Gauge Pressure Sensors;型号: | SM9233 |
厂家: | Silicon Microstructures, Inc. |
描述: | Gauge Pressure Sensors 仪表 |
文件: | 总18页 (文件大小:1635K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ultra-Low Pressure
Digital Sensor
SM9233/SM9235/SM9236 Series
Gauge Pressure Sensors
FEATURES
•
•
•
•
•
Pressure ranges: 250 up to 600 Pa Gauge
Accuracy after Autozero: < 1%FS
16 bit I2C Digital interface
Pressure calibrated and temperature compensated output
Compensated temperature range: -20 to 85oC
DESCRIPTION
Combining the pressure sensor with a signal-conditioning ASIC in a
single package simplifies the use of advanced silicon micro-machined
pressure sensors. The pressure sensor can be mounted directly on a
standard printed circuit board and a high level, calibrated pressure
signal can be acquired from the digital interface. This eliminates the
need for additional circuitry, such as a compensation network or
microcontroller containing a custom correction algorithm.
The SM923x series are digital, ultra-low pressure sensors offering
state-of-the-art MEMS pressure transducer technology and CMOS
mixed signal processing technology to produce a digital, fully
conditioned, multi-order pressure and temperature compensated
sensor in JEDEC standard SOIC-16 package with a dual vertical
porting option. It is available in a gauge pressure configuration.
The total accuracy after board mount and system level autozero is
less than 1%FS. The excellent warmup behavior and long term
stability further assures its expected performance over the life of the
part.
The SM9233/SM9235/SM9236 are shipped in sticks or tape & reel.
Medical
Industrial
Sleep Apnea
CPAP
HVAC / VAV
Airflow Measurement
Pressure Transmitters
Pneumatic Gauges
Pressure Switches
Ventilators
Gas Flow Instrumentation
Air Flow Monitors
Life Sciences
Safety Cabinets
Gas Flow Instrumentation
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 1
SM9233/SM9235/SM9236 Series
www.si-micro.com
1. Absolute Maximum Ratings
All parameters are specified at Vdd = 3.3 V supply voltage at 25oC, unless otherwise noted.
No.
Characteristic
Supply Voltage
Symbol
VDD
Minimum
Maximum
Units
1
2
3
3.0
-0.3
-10
5.5
VDD+0.3
+10
V
V
Digital IO Voltage
VIO,DIG
IIO,DIG
Max. Digital IO Current (DC)
mA
4
5
6
Storage Temperature(a,b)
Proof Pressure (a, c)
TSTG
PProof
PBurst
-40
+125
°C
7 (1.0)
20 (2.9)
kPa (PSI)
kPa (PSI)
Burst Pressure (a, d)
Notes:
a. Tested on a sample basis.
b. Clean, dry air compatible with wetted materials. Wetted materials include silicon, glass, RTV (silicone), gold, aluminum, copper, nickel,
palladium, epoxy, stainless steel and plastic (mold compound).
c. Proof pressure is defined as the maximum pressure to which the device can be taken and still perform within specifications after
returning to the operating pressure range.
d. Burst pressure is the pressure at which the device suffers catastrophic failure resulting in pressure loss through the device.
2. ESD
No.
Description
Symbol
Minimum
Maximum
Units
2.1
ESD HBM Protection at all Pins
VESD(HBM)
-2
2
kV
3. External Components
No.
Description
Symbol
CVDD
Min.
Typ.
100
Max.
Units
nF
1
2
Supply bypass capacitor*
I2C Data and clock pull up resistors*
RP
4.7
kOhm
* Not tested in production
4. Calibrated Pressure Ranges
Calibrated Pressure Ranges
PMIN (Pa)
No.
Device Type
SM9233 – 250 Gauge
SM9235 –300 Gauge
SM9236 –600 Gauge
PMAX (Pa)
1
2
3
0
0
0
+250
+300
+600
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 2
SM9233/SM9235/SM9236 Series
www.si-micro.com
5. Recommended Operating Conditions
The recommended operating conditions must not be exceeded in order to ensure proper functionality of the device. All parameters
specified in the following sections refer to these recommended operating conditions unless stated otherwise.
No.
Description
Symbol
Min.
Typ.
Max.
Units
1
Supply Voltage
VVDD
3.0
3.3
5.5
V
2
Low level input voltage at SDA, SCL
VIN,I2C,lo
-0.3
0.9
V
3
4
5
High level input voltage at SDA, SCL
Compensated Temperature (b)
Operating Temperature
VIN,I2C,hi
TCOMP
TA
0.8 * VVDD
-20
VVDD+0.3
+85
V
°C
°C
-20
85
Notes:
b. Clean, dry air compatible with wetted materials.
6. OPERATING CHARACTERISTICS TABLE
All parameters are specified at Vdd = 3.3 V or 5 V DC supply voltage (as per P/N counter in table 10) at 25oC, unless otherwise noted.
No.
Characteristic
Supply Current at 3.3V (e)
Supply Current at 5.0V (e)
Digital Pressure Output @ PMIN
Digital Pressure Output @ PMAX
Digital Full Scale Span
Symbol
IVDD3p3
IVDD5p0
OUTMIN
OUTMAX
FS
Minimum
Typical
Maximum
Units
mA
3.3
4.1
1
3.9
-26,215
5.0
2
3
4
5
6
Counts
Counts
Counts
Bits
+26,214
52,429
16
Resolution (Digital Output)
Update Rate
2000
± 0.25
± 0.2
± 0.1
± 0.5
± 0.4
± 0.3
20
Hz
SM9233 – 250 Gauge
-1.25
-1.0
1.25
1.0
%FS
Digital AZ
SM9235 – 300 Gauge
SM9236 – 600 Gauge
SM9233 – 250 Gauge
SM9235 – 300 Gauge
SM9236 – 600 Gauge
Bandwidth
%FS
7
8
Output
ACCAZ
ACC
Accuracy (f, g, h)
-1.0
1.0
%FS
-2.75
-2.3
2.75
2.3
%FS
Digital Output
Accuracy (f)
-1.25
1.25
%FS
Hz
9
BW
SG
10
Position Sensitivity
From supply VDD > 3.0 V
0.1
%FS/g
Power-up
time*
to output settled to 63%
of final value
tUP
18
18
ms
ms
ms
11
12
13
Pressure step response;
settled to 63% of final
value
Step response
time*
tRESP
Pressure step response;
output settled to full
accuracy
Step response
settling time*
tSETTLE
45
* Not tested in production
Notes:
e. Supply current given for continuous operation. Device can be set to sleep mode with significantly lower power consumption. Refer to section 11 for details.
f. The accuracy specification applies over all operating conditions in dry clean air. This specification includes the combination of linearity, repeatability, and
hysteresis errors over pressure, temperature, and 3.3 V supply voltage.
g. Based on system level autozero at 25 oC after board mount or solder reflow.
h. Based on sample testing during initial product qualification, not tested in production.
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 3
SM9233/SM9235/SM9236 Series
www.si-micro.com
7 I2C Interface
No.
Description
Condition
Symbol
Min.
Typ.
Max. Units
1
SDA output low voltage*
ISDA = 3 mA
VSDA,OL
0
0.4
V
2
3
Low-to-High transition threshold*
High-to-Low transition threshold*
pins SA0, SCL
pins SA0, SCL
VSDA,LH
VSDA,HL
0.5
0.3
0.6
0.4
0.7
0.5
VDD
VDD
4
5
I2C clock frequency*
Bus free time between a START and STOP condition*
Clock low time*
fSCL
tBUSF
tLO
tHI
400
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
1300
1300
600
100
100
0
6
7
Clock high time*
8
START condition hold time*
Data setup time*
tSH
tSU
tH
9
10
11
12
13
14
Data hold time*
Setup time for repeated START condition*
Setup time for STOP condition*
Rise time of SDA and SCL signals*
Fall time of SDA and SCL signals*
tRSH
tPSU
tR
600
600
300
300
tF
* Not tested in production
8. Qualification Standards
REACH Compliant
RoHS Compliant
PFOS/PFOA Compliant
For qualification specifications, please contact Sales at sales@si-micro.com
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 4
SM9233/SM9235/SM9236 Series
www.si-micro.com
9. Package Reference
SOIC-16 (C) Vertical Package Dimensions
Notes:
•
•
•
All dimensions in units of [mm]
Moisture Sensitivity Level (MSL): Level 3
Clean, dry air compatible with wetted materials. Wetted materials include : Wetted materials include silicon, glass, RTV (silicone), gold,
aluminum, copper, epoxy and mold compound.
•
•
•
Tolerance on all dimensions ±0.13 mm unless otherwise specified.
[B] is tube connected to bottom side of sensor die.
[T] is tube connected to top side of sensor die. Topside pressure is positive pressure. An increase in topside pressure will result in an
increase in sensor output
•
•
•
Bottom plate is stainless steel
Robust JEDEC SOIC-16 package for automated assembly
Manufactured according to ISO9001 , ISO14001 and ISO/TS 16949 standards
Lot Number Identification
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 5
SM9233/SM9235/SM9236 Series
www.si-micro.com
SM9233/SM9235/SM9236 Applications Circuit
Package Labeling
Pin No.
Pin Function
1
NC (No Connect)
2
NC
3
NC
4
NC
5
VSS
6
VDD
7
NC
8
NC
9
NC
10
11
12
13
14
15
16
SDA
SCL
NC
GND (ASIC Test Pin)
NC
NC
NC
NOTES:
Do not connect to NC pins
•
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
Package Pin-Out
DOC # 40DS9202.03
Page 6
SM9233/SM9235/SM9236 Series
www.si-micro.com
10. Ordering Information
Part Number
Pressure Range
Voltage Shipping
Comment
Sticks (45 parts/stick)
SM9233-BCE-S-250-000
a
a
a
0 to +250 Pa
3.3 V
3.3 V
3.3 V
Bandwidth 20Hz
Tape and Reel (350 parts/reel)
SM9233-BCE-T-250-000
SM9235-BCE-S-300-000
SM9235-BCE-T-300-000
Sticks (45 parts/stick)
0 to +300 Pa
0 to +600 Pa
Bandwidth 20Hz
Bandwidth 20Hz
Tape and Reel (350 parts/reel)
Sticks (45 parts/stick)
SM9236-BCE-S-600-000
SM9236-BCE-T-600-000
SM9233-BCE-S-250-002
Tape and Reel (350 parts/reel)
Sticks (45 parts/stick)
a
a
a
0 to +250 Pa
0 to +300 Pa
0 to +600 Pa
5.0 V
5.0 V
5.0 V
Bandwidth 20Hz
Bandwidth 20Hz
Bandwidth 20Hz
Tape and Reel (350 parts/reel)
SM9233-BCE-T-250-002
SM9235-BCE-S-300-002
SM9235-BCE-T-300-002
Sticks (45 parts/stick)
Tape and Reel (350 parts/reel)
Sticks (45 parts/stick)
SM9236-BCE-S-600-002
SM9236-BCE-T-600-002
Tape and Reel (350 parts/reel)
NOTES:
a. Contact SMI for bandwidths other than 20 Hz
Package Pin-Out
11. Part Number Legend
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 7
SM9233/SM9235/SM9236 Series
www.si-micro.com
12. Typical Characteristics
* Zero pressure accuracy tested at 30 oC and 3.3V. Measured after HTOL (at
105 oC and 5.5V) at 168, 500 and 1000 hrs. Not tested in production
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 8
SM9233/SM9235/SM9236 Series
www.si-micro.com
13. Functional Description
13.1 Overview
The SM9x3x series is a high precision, factory calibrated Gauge pressure sensor for ultra low pressure measurements. It combines a low
pressure MEMS die with a 16 bit ASIC, utilizing DSP for multi dimensional polynomial error correction. The calibrated pressure output data
is available via digital data interface (I2C). Status information on the sensor integrity and unique serial number are accessible via this
digital interface.
13.2 Global Sensor Parameters
13.2.1 Digital Pressure Transfer Function
In general digital output data is available with a word length of 16 bit. The numeric representation is always as 2's complement, which
results in a range of:
0 ... +32767 counts (positive range, or 0000h ... 7FFFh)
-32768 ... -1 counts (negative range, or 8000h ... FFFFh)
The pressure sensor device is calibrated in the end-of-line production test over the specified Pmin to Pmax pressure range (see Section 4).
The output code at Pmin is nominally -26,215 and at Pmax it is nominally 26,214. This allows the sensor to still operate monotically outside
its nominal range till the maximum (or minimum) counts are reached. An example for a 250 Gauge SM9233-BCE-S-250-000 is given in the
graph below
Green: Accuracy per specification
Red and Blue: Outside specification, but expect monotonic behavior till maximum (or minimum) code is
reached
13.2.2 Conversion from counts to pressure
The digital output count gives a signed 16 bit value for pressure and to convert the count to a pressure percent reading, p%FS, (in % full
scale pressure) the following equation can be used
The equation below converts p%FS to actual calibrated pressure units pp-unit with pmin and pmax as specified in section 4
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 9
SM9233/SM9235/SM9236 Series
www.si-micro.com
13.2.4 Digital Temperature Transfer Function
An internal temperature sensor measures the chip temperature. The temperature characteristic is linear and is described by the following
equation:
DT = b1 * TA + b0
The temperature transfer function parameters are as follows:
Temperature
Digital Output
Sensitivity / Offset
Symbol
TA,1
Temperature [°C]
Symbol
DT,OUT,1
DT,OUT,2
Value [counts ]
-32768
Symbol
Value
397.2
Unit
-40
b1
b0
counts/°C
counts
TA,2
125
32767
-16881
The typical temperature accuracy at 30 °C is within ± 2 °C.
13.3 Voltage Supply
The device is supplied from pin VDD, typically 3.3 V, but it can operate as high as 5 V. From this supply input several internal voltage
regulators are generating stabilized voltage levels for analog and digital circuit sections. The different internal voltages are monitored by
power-OK diagnostic circuitry. Also a stabilized voltage for the resistive MEMS pressure sensor is derived from VDD.
The digital data interface allows to set it into Sleep Mode using a specific command (Enter Sleep Mode), which ensures very low
consumption (IVDD,SM) of typically less than 10 µA. Of course, in Sleep Mode no pressure data is acquired.
For the I2C command to send the sensor into Sleep Mode see 13.6. To wake-up the sensor to normal operation, the clock input SCL shall be
toggled (a rising edge at SCL will wake-up the device).
13.4 Diagnosis Functions
13.4.1 MEMS Sensor Bridge Diagnostics
Internal errors of the MEMS pressure sensor are detected and the STATUS registers can be read via the digital I2C interface.
Bridge Diagnostics
An integrated bridge diagnostic circuit supervises the resistive pressure sensor to detect any of the faults as follows:
•
Sensor faults:
•
•
Short of any of the four bridge resistors of the pressure sensor
Interruption of any of the four of bridge resistors
•
Wiring faults:
•
•
Open connection of any of the bridge supply or signals
Wrong connection of any sensor bridge terminal to either ground or bridge supply
The MEMS sensor bridge diagnostics are active permanently (true background diagnostics) and in case of an error the bridge check fail
event is indicated by setting the bit bc_fail in the internal STATUS register.
Bridge Supply Diagnostics
Another diagnostic function checks if the supply to the sensor bridge is in its specified range. Here, in case of a supply error the bit bs_fail
in the STATUS register will be set.
13.4.2 Configuration Memory Check
The integrity of data stored in the embedded NVM used as the configuration memory (calibration parameters, device configuration,
device ID, etc.) is checked at power-up of the component by calculation of a check sum (CRC). If a check sum error is detected no reliable
pressure calculation is possible.
Therefore, the sensor remains in idle state, i.e. no pressure data transferred to the output registers DSP_T and DSP_S. In this case the bits
STATUS.dsp_s_up and dsp_t_up will never be set.
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 10
SM9233/SM9235/SM9236 Series
www.si-micro.com
13.5 I2C Interface
The SM9x3x features an I2C slave interface. This interface provides direct access to registers of the memory of the SM9x3x sensor. An
external I2C master (e.g. a microcontroller) can read from and write to memory addresses (registers) of the device using the following
commands:
•
•
•
Random write: Sets a memory address and writes data to consecutive memory addresses of the device starting at the set memory
address.
Random read: Sets a memory address and reads data from consecutive memory addresses of the device starting at the set memory
address.
Read last: Reads data from the device starting at the last memory address set by the master. This facilitates repeated reading of the
same memory addresses without transmitting a memory address first.
All reads/writes must start at word aligned addresses (i.e. LSB of memory address equals 0) and read/write an even number of bytes.
I2C Interface Timing Diagram:
13.5.1 I2C Command Format
The SM9x3x-Sensor uses a standard 7-bit I2C slave address field. The LSB of the slave address specifies the frame type used to perform read
and write operations.
For LSB = 0 the protocol is compatible to standard I2C EEPROMs, for LSB = 1 the protocol is extended by a CRC protection. Thus, each device
occupies two I2C addresses: even addresses are for standard EEPROM compatible protocols and odd addresses are for CRC protected
protocols. Unprotected and CRC protected frames can be interleaved.
The two different frame types - standard EEPROM (without CRC) or CRC protected - are shown in the next two figures.
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 11
SM9233/SM9235/SM9236 Series
www.si-micro.com
I2C Read / Write Commands - Standard EEPROM compatible protocol:
I2C Read / Write Commands - CRC protected protocol:
The memory address field sets the byte address of the first memory location to be read from or written to. Only 16-bit-word aligned
reads/writes are supported, i.e. the LSB of memory address has to be zero always. The read/write data is transferred MSB first, low byte
before high byte.
The length field (bits[7:4]) required for CRC protected frames specifies the number of data bytes to be transferred decremented by one,
i.e. a value of 0001b corresponds to two bytes. All frames must transfer an even number of bytes. The maximum length for CRC protected
read/write frames is 16/4 bytes. For unprotected frames the length is unlimited.
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 12
SM9233/SM9235/SM9236 Series
www.si-micro.com
The CRC4 and CRC8 for redundancy check are computed in the same bit and byte order as the transmission over the bus. The polynomials
employed are:
•
•
CRC4: polynomial 0x03; initialization value: 0x0F
CRC8: polynomial 0xD5; initialization value: 0xFF
If a CRC errors occurs, then the event bit com_crc_error in the STATUS register will be set.
13.5.2 I2C Command Examples
For all examples below the 7-bit device slave address used is 0x6C for unprotected commands, and 0x6D for CRC protected commands,
respectively.
The command sequence following describes an unprotected Read command (without CRC) of 3 subsequent 16-bit words starting at
memory address 0x2E to read the corrected IC temperature, corrected pressure signal, and (synchronized) status bits of the sensor.
Random Read:
Byte #
0
1
2
3
4
5
6
7
8
SBM
(sent by master)
0xD8
0x2E
0xD9
slave
slave
address 6C memory address 6C
SBM comment
+ LSB = 0
address
+ LSB = 1
for Write
for Read
SBS
0xF2
0x7D
0xEA
0x82
0x1E
0x00
(sent by sensor)
sync‘ed
Status
(b7 - b0)
ad. 0x32
DSP_T
(Lo-Byte)
ad. 0x2E
DSP_S
(Lo-Byte)
ad. 0x30
sync‘ed
Status
(b15 - b8)
DSP_T
(Hi-Byte)
DSP_S
(Hi-Byte)
SBS comment
The following sequence writes one 16-bit word to address 0x22. This will copy 0x6C32 into the command register CMD to move the
component to Sleep Mode.
Random Write:
Byte #
0
1
2
3
SBM
(sent by master)
0xD8
0x22
0x32
0x6C
slave address 6C
+ LSB = 0
Lo-Byte written to
CMD[7:0]
Hi-Byte written to
CMD[15:8]
SBM comment
memory address
for Write
SBS
(sent by sensor)
SBS comment
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 13
SM9233/SM9235/SM9236 Series
www.si-micro.com
The next command sequence describes a CRC protected Read command of 3 subsequent 16-bit words starting at memory address 0x2E.
Random Read - protected by CRC:
Byte #
0
1
2
3
4
5
6
7
8
9
10
SBM
(sent by
master)
0xDA
0x2E
0x5B
0xDB
slave
address
6D
+ LSB = 0
for Write
slave
3: length address
= 4Byte 6D
memory
address
SBM comment
B: CRC4 + LSB = 1
for Read
SBS
0xF2
0x7D
0xEA
0x82
0x1E
0x00
0x65
(sent by sensor)
sync‘ed
Status
(Hi-Byte) (b7 - b0)
ad. 0x32
DSP_T
(Lo-Byte)
ad. 0x2E
DSP_S
(Lo-Byte)
ad. 0x30
sync‘ed
Status
(b15 - b8)
DSP_T
(Hi-Byte)
DSP_S
CRC8
(calc'd)
SBS comment
The next example describes a Write of one 16-bit word (contents 0xCF9E) with CRC protection to address 0x36 to clear events in the
STATUS register.
Random Write - protected with CRC:
Byte #
0
1
2
3
4
5
SBM
(sent by master)
0xDA
0x36
0x16
0x9E
0xCF
0xA1
slave address 6D
+ LSB = 0
1: length = 2Byte
6: CRC4
STATUS
(Lo-Byte)
ad. 0x36
STATUS
(Hi-Byte)
CRC8
(calculated)
SBM comment
memory address
for Write
SBS
(sent by sensor)
SBS comment
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 14
SM9233/SM9235/SM9236 Series
www.si-micro.com
13.6 Register Descriptions
Register Read or Write are performed via the digital communication interface. After power-up of the IC all registers except STATUS and
CMD are write protected.
Command register:
0x22
CMD
bits
name
default
rw
description
Writing to this register controls the state of the SM9x3x device.
0x6C32: SLEEP Mode
Initiate the power state SLEEP, powering down the ASIC
15:0
cmd
0
w
0xB169: RESET
Performs a reset. After reset the power-up sequence will be executed, i.e. the registers
are loaded with data from the configuration memory, also a CRC check is performed.
Temperature register:
0x2E
DSP_T
bits
name
default
rw
description
Corrected temperature measurement value of the sensor.
Whenever this register is updated with a new measurement the STATUS.dsp_t_up event
bit is set.
15:0
dsp_t
r
Pressure register:
0x30
DSP_S
bits
name
default
rw
description
corrected pressure measurement value of the sensor.
Whenever this register is updated with a new measurement the STATUS.dsp_s_up event
bit is set.
15:0
dsp_s
r
The registers DSP_T and DSP_S contain invalid data after power-up until the first temperature and pressure values have been measured by
the device and transferred to these registers. In case a NVM CRC error occurred, the DSP_T and DSP_S registers would never be updated.
Thus, after power up it is necessary to wait until the STATUS.dsp_s_up and dsp_t_up bits have been set at least once before using the
temperature or pressure data. It is not sufficient to wait just for a fixed time delay.
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 15
SM9233/SM9235/SM9236 Series
www.si-micro.com
Status register - synchronized:
0x32 STATUS_SYNC
bits
0
name
idle
default
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
type
status
event
event
event
event
status
status
event
event
event
status
event
status
status
event
event
description
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
STATUS.idle
1
- reserved -
- reserved -
dsp_s_up
dsp_t_up
reserved
2
reserved
3
when DSP_S is read STATUS.dsp_s_up is copied here
4
when DSP_T is read STATUS.dsp_t_up is copied here
5
- reserved -
- reserved -
bs_fail
reserved
reserved
6
7
STATUS.bs_fail
STATUS.bc_fail
reserved
8
bc_fail
9
- reserved -
dsp_sat
10
11
12
13
14
15
STATUS.dsp_sat
STATUS.com_crc_error
reserved
com_crc_error
- reserved -
- reserved -
dsp_s_missed
dsp_t_missed
reserved
STATUS.dsp_s_missed
STATUS.dsp_t_missed
The bits STATUS_SYNC[15:5,0] are identical to the bits STATUS[15:5,0].
The bits STATUS_SYNC[4:3] are copied from the STATUS register when the corresponding DSP registers are read. First reading the DSP
registers and then STATUS_SYNC ensures that both values are consistent to each other.
The synchronized status STATUS_SYNC register can be used to continuously poll the pressure, temperature and status of the device with
a single read command by reading three 16 bit words starting at address 0x2E. By evaluating STATUS_SYNC.dsp_t_up and
STATUS_SYNC.dsp_s_up it can be determined if the values in DSP_T and DSP_S acquired during the same read contain recently updated
temperature or pressure values.
Status register:
0x36
bits
0
STATUS
name
default
rw
type1
description
0: chip in busy state
1: chip in idle state
idle
0
rw
status
1
2
- reserved -
- reserved -
0
0
rw
rw
event
event
reserved
reserved
1: DSP_S register has been updated.
Cleared when DSP_S is read
3
4
dsp_s_up
dsp_t_up
0
0
rw
rw
event
event
1: DSP_T register has been updated.
Cleared when DSP_T is read.
5
6
7
8
9
- reserved -
- reserved -
bs_fail
0
0
0
0
0
rw
rw
rw
rw
rw
status
status
event
event
event
reserved
reserved
1: bridge supply failure occurred
1: sensor bridge check failure occurred
reserved
bc_fail
- reserved -
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 16
SM9233/SM9235/SM9236 Series
www.si-micro.com
0x36
bits
STATUS
name
default
rw
type1
description
1: a DSP computation leading to the current DSP_T or DSP_S values
was saturated to prevent overflow
10
dsp_sat
0
rw
status
11
12
13
14
15
com_crc_error
- reserved -
0
0
0
0
0
rw
rw
rw
rw
rw
event
status
status
event
event
1: communication CRC error
reserved
- reserved -
reserved
dsp_s_missed
dsp_t_missed
1: dsp_s_up was 1 when DSP_S updated
1: dsp_t_up was 1 when DSP_T updated
1)
•
"Event" type flags remain set until cleared by writing '1' to the respective bit position in STATUS register (not STATUS_SYNC). Writing
0xFFFF to the STATUS register will clear all event bits.
•
"Status" type flag represents a condition of a hardware module of the IC and persists until the condition has disappeared.
Serial Number register 0:
0x50
SER0
bits
15:0
name
ser0
default
default
rw
description
r
Serial number of the IC, Lo-Word
Serial Number register 1:
0x50
SER1
bits
15:0
name
ser1
rw
description
r
Serial number of the IC, Hi-Word
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
SM9233/SM9235/SM9236 Series
www.si-micro.com
Silicon Microstructures Warranty and Disclaimer:
Silicon Microstructures, Inc. reserves the right to make changes without further notice to any products herein and to
amend the contents of this data sheet at any time and at its sole discretion.
Information in this document is provided solely to enable software and system implementers to use Silicon
Microstructures, Inc. products and/or services. No express or implied copyright licenses are granted hereunder to design
or fabricate any silicon-based microstructures based on the information in this document.
Silicon Microstructures, Inc. makes no warranty, representation, or guarantee regarding the suitability of its products for
any particular purpose, nor does Silicon Microstructures, Inc. assume any liability arising out of the application or use of
any product or silicon-based microstructure, and specifically disclaims any and all liability, including without limitation
consequential or incidental damages. “Typical” parameters which may be provided in Silicon Microstructure’s data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Silicon
Microstructures, Inc. does not convey any license under its patent rights nor the rights of others. Silicon Microstructures,
Inc. makes no representation that the circuits are free of patent infringement. Silicon Microstructures, Inc. products are
not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Silicon
Microstructures, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or
use Silicon Microstructures, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and
hold Silicon Microstructures, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Silicon
Microstructures, Inc. was negligent regarding the design or manufacture of the part.
Silicon Microstructures, Inc. warrants goods of its manufacture as being free of defective materials and faulty
workmanship. Silicon Microstructures, Inc. standard product warranty applies unless agreed to otherwise by Silicon
Microstructures, Inc. in writing; please refer to your order acknowledgement or contact Silicon Microstructures, Inc.
directly for specific warranty details. If warranted goods are returned to Silicon Microstructures, Inc. during the period of
coverage, Silicon Microstructures, Inc. will repair or replace, at its option, without charge those items it finds defective.
The foregoing is buyer’s sole remedy and is in lieu of all warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no event shall Silicon Microstructures, Inc. be liable for
consequential, special, or indirect damages.
While Silicon Microstructures, Inc. provides application assistance personally, through its literature and the Silicon
Microstructures, Inc. website, it is up to the customer to determine the suitability of the product for its specific
application. The information supplied by Silicon Microstructures, Inc. is believed to be accurate and reliable as of this
printing. However, Silicon Microstructures, Inc. assumes no responsibility for its use. Silicon Microstructures, Inc. assumes
no responsibility for any inaccuracies and/or errors in this publication and reserves the right to make changes without
further notice to any products or specifications herein
Silicon Microstructures, Inc.TM and the Silicon Microstructures, Inc. logo are trademarks of Silicon Microstructures, Inc. All
other service or product names are the property of their respective owners.
© Silicon Microstructures, Inc. 2001-2019 All rights reserved.
+1-(408) 577-0100 | sales@si-micro.com I www.si-micro.com
Silicon Microstructures, Inc. 2001-2019. All rights reserved
DOC # 40DS9202.03
Page 18
相关型号:
©2020 ICPDF网 联系我们和版权申明