SDP7915ANHD [SOLITRON]
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON;型号: | SDP7915ANHD |
厂家: | Solitron Devices |
描述: | MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON |
文件: | 总12页 (文件大小:145K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
Update drawing to reflect current requirements.
05-01-20
09-09-02
Raymond Monnin
Charles F. Saffle
Figure 2, case outlines N and T, correct terminal number 2. Add note
to table II, Group C end-point electrical parameters. -gz.
C
Updated drawing paragraphs. -sld
12-05-15
Charles F. Saffle
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
REV
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
C
SHEET
10
11
PMIC N/A
PREPARED BY
Gary Zahn
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Michael C. Jones
APPROVED BY
Raymond Monnin
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
MICROCIRCUIT, LINEAR, VOLTAGE
REGULATOR, 15 VOLT, NEGATIVE, FIXED,
MONOLITHIC SILICON
DRAWING APPROVAL DATE
99-07-30
AMSC N/A
REVISION LEVEL
C
SIZE
A
CAGE CODE
5962-98641
67268
SHEET
1 OF 11
DSCC FORM 2233
APR 97
5962-E168-12
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
-
98641
01
H
T
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number 1/
SDP7915A
Circuit function
Negative voltage regulator, 15 volt, fixed
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
K
Device performance documentation
Highest reliability class available. This level is intended for use in space
applications.
H
G
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E
D
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1/ The SDP7915A is similar to the 7915A listed on Standard Microcircuit Drawing 5962-88748.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
2
DSCC FORM 2234
APR 97
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
See figure 1
Terminals
Package style
N
T
U
Z
3
3
3
3
Z-tab with nonisolated tab,
(TO-257Z), with glass seal
Flange mount with nonisolated tab,
(TO-257), with glass seal
Flange mount with isolated tab,
(TO-257), with glass seal
See figure 1
See figure 1
See figure 1
Z-tab with isolated tab,
(TO-257Z), with glass seal
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage:
Operating or output shorted to ground ...................................
Transient ................................................................................
Storage temperature range........................................................
Lead temperature (soldering, 10 seconds) ................................
-35 V dc
-50 V dc 2/
-65°C to +150°C
+300°C
Junction temperature (TJ) ..........................................................
Power dissipation (PD):
+150°C 3/
TC = +25°C.............................................................................
TA = +25°C.............................................................................
15 W
3.0 W
Thermal resistance, junction-to-case (qJC):
Cases N and T .......................................................................
Cases U and Z .......................................................................
Thermal resistance, junction-to-ambient (qJA) ...........................
3.5°C/W
4.2°C/W
42°C/W
1.4 Recommended operating conditions.
Input voltage range....................................................................
Ambient operating temperature range (TA)................................
-17.5 V dc to -30 V dc
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at
the maximum levels may degrade performance and affect reliability.
2/ The -50 volt input rating refers to the ability of the regulator to withstand high line or transient condition without
damage. Since the regulator's maximum current capability is reduced, the output may fall out of regulation at high
input voltages under nominal loading.
3/ The device is protected by a thermal shutdown circuit which is designed to turn off the output transistor whenever
the device junction temperature is in excess of +150°C.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
3
DSCC FORM 2234
APR 97
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55°C < TA < +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Unit
Min
Max
Output voltage
1
01
-14.85
-14.55
-15.15
-15.45
V
TA = +25°C
VOUT
VIN = -17.5 V to -30 V 2/
1, 2, 3
Line regulation 3/ 4/
Load regulation 3/
Standby current drain
VRLINE
1
2, 3
1
01
01
01
01
01
20
50
15
25
35
75
21
45
6.0
6.5
0.8
mV
mV
mV
mV
mA
VIN = -17.5 V to -30 V
VIN = -20 V to -26 V
2, 3
1
VRLOAD
VIN = -20 V,
IO = 5.0 mA to 1.5 A
2, 3
1
VIN = -20 V,
IO = 250 mA to 750 mA
2, 3
1
ISCD
2, 3
1, 2, 3
Standby current drain
change with line
VIN = -17.5 V to -30 V
IO = 5.0 mA to 1.0 A
01
01
01
mA
mA
V
D ISCD
(line)
Standby current drain
change with load
1, 2, 3
1, 2, 3
0.5
2.5
D ISCD
(load)
Dropout voltage
ΔVOUT = 100 mV,
VDO
IO = 1.0 A
Peak output current
1
01
01
1.5
3.3
A
A
TA = +25°C
IO(pk)
IOS
Short circuit current 5/
1
2, 3
1.2
2.8
VIN = -35 V
DVIN
DVOUT
Ripple rejection
f = 120 Hz, IO = 0.5 A,
4
01
53
50
dB
VIN = -18 V to -28 V
5, 6 6/
See footnotes at end of table.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions 1/
-55°C < TA < +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Min
Unit
Max
40
NO
f = 10 Hz to 100 kHz,
TA = +25°C
7
7
01
01
μV/V
rms
Output noise voltage 6/
Long term stability 6/
DVOUT
Dt
t = 1000 hours,
TA = +25°C
150
mV
1/ Unless otherwise specified, VIN = -23 V and IO = 500 mA.
2/
IO = 5 mA to 1.0 A, P £ 15 W.
3/ All measurements except output noise voltage and ripple rejection are made at constant junction temperature and
with low duty cycle.
4/ Minimum load current for full line regulation is 5.0 mA.
5/ Short circuit protection is only assured up to VIN = -35 V.
6/ If not tested, shall be guaranteed to the limits specified in table I.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
6
DSCC FORM 2234
APR 97
Case outlines T and U.
Inches
0.005
0.010
0.020
mm
0.13
0.25
0.51
Millimeters
Inches
Min Max
Symbol
Min
Max
A
A1
A2
øb
D
D1
D3
e
4.83
0.89
3.05 BSC
0.64
16.38
10.41
0.00
5.08
1.14
.190
.035
.120 BSC
.025
.645
.410
.000
.200
.045
0.89
16.89
10.92
1.65
.035
.665
.430
.065
2.54 BSC
.100 BSC
E
L
O
øP
10.41
12.70
13.39
3.56
10.72
19.05
13.64
3.81
.410
.500
.527
.140
.422
.750
.537
.150
NOTE:
The U.S. government preferred system of measurement is the metric SI system. However, this item was originally
designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the
inch-pound units shall take precedence.
FIGURE 1. Case outlines.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
7
DSCC FORM 2234
APR 97
Case outlines N and Z.
Symbol
Millimeters
Inches
Min
Min
23.11
10.41
6.22
3.05
0.71
4.70
2.92
0.89
Max
23.37
10.67
6.48
3.30
0.81
5.59
3.18
1.14
Max
.920
.420
.255
.130
.032
.220
.125
.045
A
A1
A2
A3
øb
D
.910
.410
.245
.120
.028
.135
.115
.035
D1
D2
e
2.54 BSC
.100 BSC
L
10.41
12.70
6.22
10.67
19.05
6.48
.410
.500
.245
.120
.120
.420
.750
.255
.130
.130
L1
L2
L3
øP
3.05
3.30
3.05
3.30
NOTE:
The U.S. government preferred system of measurement is the metric SI system. However, this item was originally
designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the
inch-pound units shall take precedence.
FIGURE 1. Case outlines - Continued.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
8
DSCC FORM 2234
APR 97
Device type
01
Case outlines
N and T
U and Z
(nonisolated tab)
(isolated tab)
Terminal number
Terminal symbol
Terminal symbol
1
2
Ground
Input
Ground
Input
3
Tab
Output
Input
Output
No connection
FIGURE 2. Terminal connections.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
9
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
Final electrical parameters
Group A test requirements
1
1*, 2, 3, 4
1, 2, 3, 4, 5**, 6**, 7**
1, 2, 3
Group C end-point electrical
parameters 1/
Not applicable
End-point electrical parameters
for Radiation Hardness Assurance
(RHA) devices
* PDA applies to subgroup 1.
** Subgroups 5, 6, and 7, if not tested shall be guaranteed
to the limits specified in table I.
1/ As a minimum, for all Group C testing performed after September 2, 2009
manufacturers shall perform subgroups 1, 2, and 3 from the Group A
electrical test table (Table C-Xa of MIL-PRF-38534).
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
(2) TA as specified in accordance with table I of method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
10
DSCC FORM 2234
APR 97
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. Tests shall be as specified in table II herein.
b. Subgroups 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1005 of MIL-STD-883.
(2) TA as specified in accordance with table I of method 1005 of MIL-STD-883.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-
38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list
will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices
(FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to
this drawing.
SIZE
STANDARD
5962-98641
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
C
SHEET
COLUMBUS, OHIO 43218-3990
11
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 12-05-15
Approved sources of supply for SMD 5962-98641 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/ 2/
Vendor
CAGE
number
Vendor
similar
PIN 3/
5962-9864101HNA
5962-9864101HNC
21845
21845
SDP7915ANHD
SDP7915ANHG
5962-9864101HTA
5962-9864101HTC
21845
21845
SDP7915ATHD
SDP7915ATHG
5962-9864101HUA
5962-9864101HUC
21845
21845
SDP7915AUHD
SDP7915AUHG
5962-9864101HZA
5962-9864101HZC
21845
21845
SDP7915AZHD
SDP7915AZHG
1/ The lead finish shown for each PIN, representing a hermetic package, is
the most readily available from the manufacturer listed for that part. If the
desired lead finish is not listed contact the Vendor to determine availability.
2/ The SMD device types listed above are similar to the device types listed on
SMD 5962-88748.
3/ Caution. Do not use this number for item acquisition. Items acquired to this
number may not satisfy the performance requirements of this drawing.
Vendor CAGE
number
Vendor name
and address
21845
Solitron Devices, Incorporated
3301 Electronics Way
West Palm Beach, FL 33407
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号:
SDP7915ANHG
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
SDP7915ATHD
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
SDP7915ATHG
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
SDP7915AUHD
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
SDP7915AUHG
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
SDP7915AZHD
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
SDP7915AZHG
MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, 15 VOLT, NEGATIVE, FIXED, MONOLITHIC SILICON
SOLITRON
©2020 ICPDF网 联系我们和版权申明