C-135-155C-FDFB-SLC9-G5 [SOURCE]
155 Mbps Single Mode SFF LC Transceiver; 155 Mbps的单模SFF LC收发器型号: | C-135-155C-FDFB-SLC9-G5 |
厂家: | SOURCE PHOTONICS, INC. |
描述: | 155 Mbps Single Mode SFF LC Transceiver |
文件: | 总8页 (文件大小:670K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-sourced 2x5 Pin Package
• Complies with SONET OC-3 / SDH STM-1
• 1270 nm to1610 nm Wavelength, CWDM DFB Laser
• Single +3.3V Power Supply
• LVPECL Differential Inputs and Outputs
• LVTTL Signal Detection Output (C-1XX-155C-FDFB-SLCX)
• LVPECL Signal Detection Output (C-1XX-155-FDFB-SLCX)
• Class 1 Laser International Safety Standard IEC 825
compliant
• Solderability to MIL-STD-883, Method 2003
• Flammability to UL94V0
• Humidity RH 5-85% (5-90% short term) to IEC 68-2-3
• Complies with Bellcore GR-468-CORE
• 40 km reach (C-1XX-155-FDFB-SLC5), 1270 to 1450 nm
• 80 km reach (C-1XX-155-FDFB-SLC5), 1470 to 1610 nm
• 80 km reach (C-1XX-155-FDFB-SLC9), 1270 to 1450 nm
• 120 km reach (C-1XX-155-FDFB-SLC9), 1470 to 1610 nm
• RoHS-5/6 compliance available
Absolute Maximum Rating
Parameter
Symbol
Vcc
Min.
Max.
3.6
30
Unit
V
Note
Power Supply Voltage
Output Current
0
0
Iout
mA
ºC
Soldering Temperature
Operating Temperature
Storage Temperature
-
-
260
70
10 seconds on leads only
Topr
Tstg
0
ºC
-40
85
ºC
Recommended Operating Condition
Parameter
Symbol
Min.
3.1
0
Typ.
3.3
-
Max.
3.5
70
Unit
V
Power Supply Voltage
Operating Temperature (Case)
Data rate
Vcc
Topr
ºC
-
155
-
Mbps
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
1
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Optical
Po
Po
λ
-5
0
-
-
0
dBm
dBm
nm
C-1XX-155(C)-FDFB-SLC5
C-1XX-155(C)-FDFB-SLC9
Optical Transmit Power
Optical Transmit Power
Output center Wavelength
Output Spectrum Width
Side Mode Suppression Ratio
Extinction Ratio
+5
λ -5.5
λ
λ +7.5
λ =1XX0 nm
p
p
p
p
∆λ
Sr
-
-
1
-
nm
-20 dB width
CW, Po=5mW
30
10
35
-
dBm
dB
ER
-
Output Eye
Compliant with GR-253-CORE
Optical Rise Time
tr
tf
-
-
-
-
-
-
2
2
ns
ns
10% to 90% Values
10% to 90% Values
Optical Fall Time
Relative Intensity Noise
RIN
-116
dB/Hz
Measured with 223-1 PRBS with 72 ones
and 72 zeros.
Total Jitter
TJ
-
-
1.2
ns
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Electrical
Maximum current is specified at Vcc=
Maximum @ maximum temperature
ICC
-
-
180
mA
Power Supply Current
Transmit Enable Voltage
Transmit Disable Voltage
Data Input Current-Low
Data Input Current-High
Data Input Voltage-Low
Data Input Voltage-High
0
-
-
-
-
-
-
0.8
Vcc
-
V
V
VEN
2.0
-200
-
VD
IIL
µA
µA
V
I
200
-1.58
-0.74
IH
VIL-VCC
VIH-VCC
-2.0
-1.1
These inputs are compatible with 10K,
10KH and 100K ECL and PECL inputs
V
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Optical
Measured with 223-1 PRBS, BER = 10 -10
C-1XX-155(C)-FDFB-SLC5
Sensitivity
-
-
-
-35
dBm
Measured with 223-1 PRBS, BER = 10 -10
C-1XX-155(C)-FDFB-SLC9
Sensitivity
-
-
0
-
-
-
-
-36
-
dBm
dBm
dBm
Maximum Input Power
Signal Detect-Asserted
Pin
Pa
Measured on transition: low to high
C-1XX-155(C)-FDFB-SLC5
-35
Measured on transition: low to high
C-1XX-155(C)-FDFB-SLC9
Signal Detect-Asserted
Pa
Pd
-
-
-36
dBm
Signal Detect-Deasserted
Signal Detect-Hysteresis
Wavelength of Operation
-45
1.0
-
-
-
-
-
dBm
dB
Measured on transition: high to low
1100
1620
nm
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
2
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Note
Electrical
ICC
-
-
-
-
-
-
-
-
120
-1.58
-0.74
-1.58
-0.74
0.5
mA
V
The current excludes the output load current
Power Supply Current
Data Output Voltage-Low
VOL -Vcc
-2
These outputs are compatible with 10K,
10KH and 100K ECL and LVPECL outputs
Data Output Voltage-High
VOH-
-1.1
-2
V
Vcc
VSDL-Vcc
Vcc
Signal Detect Output Voltage-Low
Signal Detect Output Voltage-High
Signal Detect Output Voltage-Low
Signal Detect Output Voltage-High
V
C-1XX-155-FDFB-SLCX
C-1XX-155C-FDFB-SLCX
-1.1
-
V
VSDH-
VSDL-Vcc
Vcc
V
2.0
-
V
VSDH-
Connection Diagram
Legal Notice
PIN
Symbol
RxGND
TxVcc
SD
Notes
Directly connect this pin to the receiver ground plane
+3.3 V dc power for the receiver section
1
2
3
Active high on this indicates a received optical signal(LVPECL/LVTTL)
Receiver Data Out Bar (LVPECL)
4
RD-
5
RD+
Receiver Dat Out (LVPECL)
6
TxVcc
TxGND
TxDIS
TD+
+3.3 V dc power for the transmitter section
Directly connect this pin to the transmitter ground plane
Transmitter disable (LVTTL)
7
8
9
Transmitter Data In (LVPECL)
10
TD-
Transmitter Data In Bar (LVPECL)
The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
Attaching Posts
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
3
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Recommended Circuit Schematic
C-1XX-155-FDFB-SLCX
PHY DEVICE
Vcc(+3.3V)
TERMINATE AT
TRANSCEIVER INPUTS
Z=50�
TD-
LVPECL
100�
Z=50�
TD+
130�
130�
LVTTL
Tx Disable
10
9
8
7
6
Vcc(+3.3V)
10ꢀF
1ꢀH
C2
C3
Tx
Rx
Vcc(+3.3V)
LVPECL
1ꢀH
C1
RD+
RD-
1
2
3
4
5
Z=50�
100�
Vcc(+3.3V)
Z=50�
Z=50�
130� 130�
130
�
SD
LVPECL
82�
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
PHY DEVICE
C-1XX-155C-FDFB-SLCX
Vcc(+3.3V)
TERMINATE AT
TRANSCEIVER INPUTS
Z=50
Z=50
�
TD-
LVPECL
LVTTL
100�
�
TD+
130
�
130�
Tx Disable
10
9
8
7
6
Vcc(+3.3V)
1
ꢀH
10
ꢀF
C2
C3
Tx
Rx
Vcc(+3.3V)
LVPECL
1
ꢀ
H
C1
RD+
RD-
1
2
3
4
5
Z=50�
100
�
Vcc(+3.3V)
Z=50
�
�
130
�
130�
Z=50
SD
LVTTL
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
4
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Package Diagram
C-1XX-155(C)-FDFB-SLCX
Units: mm (inches)
+
48.8
-.
+(000)
(1.921)
-(0.008)
1050
(0.413)
050
(0.020)
625
100�005
17
(0.246)
(0.039±0.002)
712
50
(0.070)
(0.280)
(0.200)
177
(0.700)
+
48.8
-.
+(000
)
(1.921)
-(0.008)
C-1XX-155(C)-FDFB-SLCXS
Units: mm (inches)
+
-
+(.000)
-(0.008)
(1.921)
(0.274)
ꢀ
(0.531)
(0.155)
10.50
(0.413)
0.50
(0.020)
6.25
1.00�0.05
1.78
(0.246)
(0.039±0.002)
7.12
5.08
(0.070)
(0.280)
(0.200)
17.78
(0.700)
Case with metal Shielding Finger
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
5
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Printed Circuit Board Layout Consideration
A fiber-optic receiver employs a very high gain, wide bandwidth transimpedance amplifier. This amplifier detects and amplifies
signals that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the
receiver circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit.
To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must
be used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of
power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of
signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high
speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi filter
be used in both transmitter and receiver power supplies.
EMI and ESC Consideration
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs flush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis
ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the
gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of
the panel.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
6
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Recommended Board Layout Hole Pattern
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
7
155 Mbps Single Mode SFF LC Transceiver
C-1XX-155(C)-FDFB-SLCX
Ordering Information
Available Options:ꢀ
C-1XX-155-FDFB-SLC5(S)
C-1XX-155-FDFB-SLC9(S)
C-1XX-155C-FDFB-SLC5(S)
C-1XX-155C-FDFB-SLC9(S)
C-1XX-155-FDFB-SLC5(S)-G5
C-1XX-155-FDFB-SLC9(S)-G5
C-1XX-155C-FDFB-SLC5(S)-G5
C-1XX-155C-FDFB-SLC9(S)-G5
Part numbering Definition:ꢀ
C - 1XX - 155(C) - FDFB - S LC TxPower Package - RoHS
• 1XX = Wavelength 1XX0 nm
XX=27, 29, 31, 33, 35, 37, 39, 41, 43,
45, 47, 49, 51, 53, 55, 57, 59, 61
• Communication protocol
155= LVPECL SD output
155C= LVTTL SD output
• FDFB = +3.3V SFF Transceiver
• Single mode fiber
• Connector options
• Tx Power range
5 = -5 to 0 dBm
9 = 0 to +5 dBm
• Package
Blank = Standard Package
S = EMI Shielding Finger Package
• Blank = No RoHS compliant
G5 = RoHS-5/6 compliant (lead exemption)
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran-
ties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu-
ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS850-Apr0706
Rev A.2
8
相关型号:
©2020 ICPDF网 联系我们和版权申明