AM29F002T-120EI 概述
Flash, PDSO32, TSOP-32 闪存
AM29F002T-120EI 规格参数
生命周期: | Obsolete | 零件包装代码: | TSOP |
包装说明: | TSOP-32 | 针数: | 32 |
Reach Compliance Code: | unknown | ECCN代码: | EAR99 |
HTS代码: | 8542.32.00.51 | 风险等级: | 5.69 |
其他特性: | TOP BOOT BLOCK | 启动块: | TOP |
JESD-30 代码: | R-PDSO-G32 | 内存集成电路类型: | FLASH |
端子数量: | 32 | 封装主体材料: | PLASTIC/EPOXY |
封装形状: | RECTANGULAR | 封装形式: | SMALL OUTLINE |
编程电压: | 5 V | 认证状态: | Not Qualified |
表面贴装: | YES | 技术: | CMOS |
端子形式: | GULL WING | 端子位置: | DUAL |
类型: | NOR TYPE | Base Number Matches: | 1 |
AM29F002T-120EI 数据手册
通过下载AM29F002T-120EI数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载PRELIMINARY
Am29F002/Am29F002N
2 Megabit (256 K x 8-Bit)
CMOS 5.0 Volt-only Boot Sector Flash Memory
DISTINCTIVE CHARACTERISTICS
■ Single power supply operation
■ Top or bottom boot block configurations
available
— 5.0 Volt-only operation for read, erase, and
program operations
■ Embedded Algorithms
— Minimizes system level requirements
— Embedded Erase algorithm automatically
preprograms and erases the entire chip or any
combination of designated sectors
■ High performance
— Access times as fast as 55 ns
— Embedded Program algorithm automatically
writes and verifies data at specified addresses
■ Low power consumption (typical values at 5
MHz)
■ Minimum 100,000 write cycle guarantee per
— 1 µA standby mode current
— 20 mA read current
sector
■ Package option
— 32-pin PDIP
— 32-pin TSOP
— 32-pin PLCC
— 30 mA program/erase current
■ Flexible sector architecture
— One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and
three 64 Kbyte sectors
■ Compatibility with JEDEC standards
— Supports full chip erase
— Pinout and software compatible with single-
power supply Flash
— Sector Protection features:
A hardware method of locking a sector to
prevent any program or erase operations within
that sector
— Superior inadvertent write protection
■ Data# Polling and toggle bits
Sectors can be locked via programming
equipment
— Provides a software method of detecting
program or erase operation completion
Temporary Sector Unprotect feature allows code
changes in previously locked sectors
■ Erase Suspend/Erase Resume
— Suspends an erase operation to read data from,
or program data to, a sector that is not being
erased, then resumes the erase operation
■ Hardware reset pin (RESET#)
— Hardware method to reset the device to reading
array data (not available on Am29F002N)
Publication# 20818 Rev: C Amendment/+2
Issue Date: March 1998
P R E L I M I N A R Y
GENERAL DESCRIPTION
The Am29F002 Family consists of 2 Mbit, 5.0 volt-only
Flash memory devices organized as 262,144 bytes.
The Am29F002 offers the RESET# function, the
Am29F002N does not. The data appears on DQ7–
DQ0. The device is offered in 32-pin PLCC, 32-pin
TSOP, and 32-pin PDIP packages. This device is
designed to be programmed in-system with the
standard system 5.0 volt VCC supply. No VPP is
required for write or erase operations. The device can
also be programmed in standard EPROM program-
mers.
device automatically times the erase pulse widths and
verifies proper cell margin.
The host system can detect whether a program or
erase operation is complete by reading the DQ7 (Data#
Polling) and DQ6 (toggle) status bits. After a program
or erase cycle has been completed, the device is ready
to read array data or accept another command.
The sector erase architecture allows memory sectors
to be erased and reprogrammed without affecting the
data contents of other sectors. The device is fully
erased when shipped from the factory.
The standard device offers access times of 55, 70, 90,
and 120 ns, allowing high speed microprocessors to
operate without wait states. To eliminate bus contention
the device has separate chip enable (CE#), write
enable (WE#) and output enable (OE#) controls.
Hardware data protection measures include a low
VCC detector that automatically inhibits write opera-
tions during power transitions. The hardware sector
protection feature disables both program and erase
operations in any combination of the sectors of mem-
ory. This can be achieved via programming equipment.
The device requires only a single 5.0 volt power sup-
ply for both read and write functions. Internally gener-
ated and regulated voltages are provided for the
program and erase operations.
The Erase Suspend feature enables the user to put
erase on hold for any period of time to read data from,
or program data to, any sector that is not selected for
erasure. True background erase can thus be achieved.
The device is entirely command set compatible with the
JEDEC single-power-supply Flash standard. Com-
mands are written to the command register using
standard microprocessor write timings. Register con-
tents serve as input to an internal state-machine that
controls the erase and programming circuitry. Write
cycles also internally latch addresses and data needed
for the programming and erase operations. Reading
data out of the device is similar to reading from other
Flash or EPROM devices.
The hardware RESET# pin terminates any operation
in progress and resets the internal state machine to
reading array data. The RESET# pin may be tied to the
system reset circuitry. A system reset would thus also
reset the device, enabling the system microprocessor
to read the boot-up firmware from the Flash memory.
(This feature is not available on the Am29F002N.)
The system can place the device into the standby
mode. Power consumption is greatly reduced in this
mode.
Device programming occurs by executing the program
command sequence. This initiates the Embedded
Program algorithm—an internal algorithm that auto-
matically times the program pulse widths and verifies
proper cell margin.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
highest levels of quality, reliability and cost effective-
ness. The device electrically erases all bits within
a sector simultaneously via Fowler-Nordheim tun-
neling. The data is programmed using hot electron
injection.
Device erasure occurs by executing the erase com-
mand sequence. This initiates the Embedded Erase
algorithm—an internal algorithm that automatically
preprograms the array (if it is not already programmed)
before executing the erase operation. During erase, the
2
Am29F002/Am29F002N
P R E L I M I N A R Y
PRODUCT SELECTOR GUIDE
Family Part Number
Am29F002/Am29F002N
V
= 5.0 V ± 5%
= 5.0 V ± 10%
-55
CC
Speed Option
V
-70
70
70
30
-90
90
90
35
-120
120
120
50
CC
Max access time, ns (t
)
55
55
30
ACC
Max CE# access time, ns (t
)
CE
Max OE# access time, ns (t
)
OE
Note: See “AC Characteristics” for full specifications.
BLOCK DIAGRAM
DQ0–DQ7
V
CC
Sector Switches
V
SS
Erase Voltage
Generator
Input/Output
Buffers
RESET#
n/a Am29F00N
State
Control
WE#
Command
Register
PGM Voltage
Generator
Data
Latch
Chip Enable
Output Enable
Logic
STB
CE#
OE#
Y-Decoder
Y-Gating
STB
V
Detector
Timer
CC
Cell Matrix
X-Decoder
A0–A17
20818C-1
Am29F002/Am29F002N
3
P R E L I M I N A R Y
CONNECTION DIAGRAMS
NC on Am29F00N
NC on Am29F00N
RESET#
1
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
V
CC
A16
A15
A12
A7
2
WE#
A17
A14
A13
A8
3
3
4
31 30
1 32
2
4
A7
A6
5
6
A14
29
28
5
A13
A6
6
A5
A4
7
A8
27
26
25
24
23
22
21
A5
7
A9
8
A9
A4
8
A11
OE#
A10
CE#
DQ7
DQ6
PDIP
PLCC
A3
9
A11
OE#
A10
CE#
DQ7
A3
9
A2
10
11
12
13
A2
10
11
12
13
14
15
16
A1
A1
A0
A0
DQ0
DQ0
16 17
19 20
18
15
14
DQ1
DQ2
DQ5
DQ4
DQ3
V
SS
A11
A9
A8
A13
A14
A17
WE#
VCC
OE#
A10
1
2
3
4
5
6
7
8
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
CE#
DQ7
DQ6
DQ5
DQ4
DQ3
VSS
DQ2
DQ1
DQ0
A0
Standard TSOP
NC on Am29F00N RESET#
9
A16
A15
A12
A7
A6
A5
10
11
12
13
14
15
16
A1
A2
A3
A4
20818C-2
4
Am29F002/Am29F002N
P R E L I M I N A R Y
PIN CONFIGURATION
LOGIC SYMBOL
A0–A17
= 18 addresses
18
DQ0–DQ7 = 8 data inputs/outputs
A0–A17
8
CE#
=
=
=
=
Chip enable
Output enable
Write enable
DQ0–DQ7
OE#
WE#
CE#
OE#
RESET#
Hardware reset pin, active low
(not available on Am29F002N)
WE#
VCC
=
+5.0 V single power supply
(see Product Selector Guide for
device speed ratings and voltage
supply tolerances)
RESET#
N/C on Am29F002N
VSS
NC
=
=
Device ground
Pin not connected internally
20818C-3
Am29F002/Am29F002N
5
P R E L I M I N A R Y
ORDERING INFORMATION
Standard Product
AMD standard products are available in several packages and operating ranges. The order number (Valid Combi-
nation) is formed by a combination of the elements below.
Am29F002
T
-70
P
C
B
OPTIONAL PROCESSING
Blank = Standard Processing
B = Burn-In
Contact an AMD representative for more information.
TEMPERATURE RANGE
C = Commercial (0°C to +70°C)
I
= Industrial (-40°C to +85°C)
E = Extended (–55°C to +125°C)
PACKAGE TYPE
P = 32-Pin Plastic DIP (PD 032)
J = 32-Pin Rectangular Plastic Leaded Chip
Carrier (PL 032)
E = 32-Pin Thin Small Outline Package
(TSOP) Standard Pinout (TS 032)
SPEED OPTION
See Product Selector Guide and
Valid Combinations
BOOT CODE SECTOR ARCHITECTURE
T = Top sector
B = Bottom sector
DEVICE NUMBER/DESCRIPTION
Am29F002/Am29F002N
2 Megabit (256 K x 8-Bit) CMOS Flash Memory
5.0 Volt-only Program and Erase
Valid Combinations
Valid Combinations
Valid Combinations list configurations planned to be sup-
ported in volume for this device. Consult the local AMD sales
office to confirm availability of specific valid combinations and
to check on newly released combinations.
Am29F002T-55
Am29F002B-55
Am29F002NT-55
Am29F002NB-55
PC, JC, JI, EC, EI
Am29F002T-70
Am29F002B-70
Am29F002NT-70
Am29F002NB-70
PC, PI, JC, JI, EC, EI
Am29F002T-90
Am29F002B-90
Am29F002NT-90
Am29F002NB-90
PC, PI, PE,
JC, JI, JE,
EC, EI, EE
Am29F002T-120
Am29F002B-120
Am29F002NT-120
Am29F002NB-120
6
Am29F002/Am29F002N
P R E L I M I N A R Y
DEVICE BUS OPERATIONS
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register it-
self does not occupy any addressable memory loca-
tion. The register is composed of latches that store the
commands, along with the address and data informa-
tion needed to execute the command. The contents of
the register serve as inputs to the internal state ma-
chine. The state machine outputs dictate the function of
the device. The appropriate device bus operations
table lists the inputs and control levels required, and the
resulting output. The following subsections describe
each of these operations in further detail.
Table 1. Am29F002/Am29F002N Device Bus Operations
RESET#
Operation
CE#
L
OE# WE#
(n/a Am29F002N)
A0–A17
DQ0–DQ7
Read
Write
L
H
X
X
H
X
H
L
H
H
H
H
H
L
A
A
D
OUT
IN
IN
L
D
IN
CMOS Standby
V
± 0.5 V
X
X
H
X
X
High-Z
High-Z
High-Z
High-Z
CC
TTL Standby
H
L
X
X
X
Output Disable
Reset (n/a on Am29F002N)
X
Temporary Sector Unprotect
(See Note)
X
X
X
V
X
X
ID
Legend:
L = Logic Low = V , H = Logic High = V , V = 12.0 ± 0.5 V, X = Don’t Care, D = Data In, D
= Data Out, A = Address In
IN
IL
IH
ID
IN
OUT
Note: See the sections on Sector Protection and Temporary Sector Unprotect for more information. This function requires the
RESET# pin and is therefore not available on the Am29F002N device.
sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control
and gates array data to the output pins. WE# should re-
main at VIH.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. The Sector Address Tables in-
dicate the address space that each sector occupies. A
“sector address” consists of the address bits required
to uniquely select a sector. See the Command Defini-
tions section for details on erasing a sector or the entire
chip, or suspending/resuming the erase operation.
The internal state machine is set for reading array
data upon device power-up, or after a hardware reset.
This ensures that no spurious alteration of the mem-
ory content occurs during the power transition. No
command is necessary in this mode to obtain array
data. Standard microprocessor read cycles that as-
sert valid addresses on the device address inputs
produce valid data on the device data outputs. The
device remains enabled for read access until the
command register contents are altered.
After the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the “Autoselect Mode” and Autoselect
Command Sequence sections for more information.
See “Reading Array Data” for more information. Refer
to the AC Read Operations table for timing specifica-
tions and to the Read Operations Timings diagram for
the timing waveforms. ICC1 in the DC Characteristics
ICC2 in the DC Characteristics table represents the ac-
tive current specification for the write mode. The “AC
Characteristics” section contains timing specification
tables and timing diagrams for write operations.
table represents the active current specification for
reading array data.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status
bits on DQ7–DQ0. Standard read cycle timings and ICC
read specifications apply. Refer to “Write Operation
Writing Commands/Command Sequences
To write a command or command sequence (which in-
cludes programming data to the device and erasing
Am29F002/Am29F002N
7
P R E L I M I N A R Y
Status” for more information, and to each AC Charac-
teristics section for timing diagrams.
RESET#: Hardware Reset Pin
Note: The RESET# pin is not available on the
Am29F002N.
Standby Mode
The RESET# pin provides a hardware method of reset-
ting the device to reading array data. When the system
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
drives the RESET# pin low for at least a period of tRP
,
the device immediately terminates any operation in
progress, tristates all data output pins, and ignores all
read/write attempts for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is ready
to accept another command sequence, to ensure data
integrity.
The device enters the CMOS standby mode when CE#
and RESET# pins (CE# only on the Am29F002N) are
both held at VCC ± 0.5 V. (Note that this is a more re-
stricted voltage range than VIH.) The device enters the
TTL standby mode when CE# and RESET# pins (CE#
only on the Am29F002N) are both held at VIH. The de-
vice requires standard access time (tCE) for read ac-
cess when the device is in either of these standby
modes, before it is ready to read data.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VIL, the device enters
the TTL standby mode; if RESET# is held at VSS
0.5 V, the device enters the CMOS standby mode.
±
The device also enters the standby mode when the RE-
SET# pin is driven low. Refer to the next section, “RE-
SET#: Hardware Reset Pin”.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firm-
ware from the Flash memory.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
Refer to the AC Characteristics tables for RESET# pa-
rameters and timing diagram.
In the DC Characteristics tables, ICC3 represents the
standby current specification.
Output Disable Mode
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high imped-
ance state.
ICC3 in the DC Characteristics tables represents the
standby current specification.
Table 2. Am29F002/Am29F002N Top Boot Block Sector Address Table
Sector Size Address Range
Sector
SA0
SA1
SA2
SA3
SA4
SA5
SA6
A17
A16
A15
A14
A13
(Kbytes)
(in hexadecimal)
00000h–0FFFFh
10000h–1FFFFh
20000h–2FFFFh
30000h–37FFFh
38000h–39FFFh
3A000h–3BFFFh
3C000h–3FFFFh
0
0
X
X
X
64
64
64
32
8
0
1
X
X
X
1
0
X
X
X
1
1
0
X
X
1
1
1
0
0
1
1
1
0
1
8
1
1
1
1
X
16
8
Am29F002/Am29F002N
P R E L I M I N A R Y
Table 3. Am29F002/Am29F002N Bottom Boot Block Sector Address Table
Sector Size
(Kbytes)
Address Range
Sector
SA0
SA1
SA2
SA3
SA4
SA5
SA6
A17
0
A16
0
A15
0
A14
0
A13
X
(in hexadecimal)
00000h–03FFFh
04000h–05FFFh
06000h–07FFFh
08000h–0FFFFh
10000h–1FFFFh
20000h–2FFFFh
30000h–3FFFFh
16
8
0
0
0
1
0
0
0
0
1
1
8
0
0
1
X
X
32
64
64
64
0
1
X
X
X
1
0
X
X
X
1
1
X
X
X
Autoselect Mode
The autoselect mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment
to automatically match a device to be programmed with
its corresponding programming algorithm. However,
the autoselect codes can also be accessed in-system
through the command register.
dress must appear on the appropriate highest order
address bits. Refer to the corresponding Sector Ad-
dress Tables. The Command Definitions table shows
the remaining address bits that are don’t care. When all
necessary bits have been set as required, the program-
ming equipment may then read the corresponding
identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in the Command Defini-
tions table. This method does not require VID. See
“Command Definitions” for details on using the autose-
lect mode.
When using programming equipment, the autoselect
mode requires VID (11.5 V to 12.5 V) on address pin
A9. Address pins A6, A1, and A0 must be as shown in
Autoselect Codes (High Voltage Method) table. In addi-
tion, when verifying sector protection, the sector ad-
Table 4. Am29F002/Am29F002N Autoselect Codes (High Voltage Method)
A17 A12
to to
CE# OE# WE# A13 A10 A9
A8
to
A7
A5
to
A2
DQ7
to
DQ0
Description
A6
A1
A0
Manufacturer ID: AMD
L
L
L
L
H
H
X
X
V
X
X
L
X
X
L
L
01h
B0h
ID
Device ID:
Am29F002/Am29F002N
(Top Boot Block)
X
X
V
L
L
L
L
H
H
ID
L
L
L
L
L
L
H
H
H
Device ID:
Am29F002/Am29F002N
(Bottom Boot Block)
X
X
X
V
V
X
X
X
X
34h
ID
01h
(protected)
Sector Protection Verification
L
L
H
SA
L
H
L
ID
00h
(unprotected)
L = Logic Low = V , H = Logic High = V , SA = Sector Address, X = Don’t care.
IL
IH
Sector Protection/Unprotection
The hardware sector protection feature disables both
program and erase operations in any sector. The
hardware sector unprotection feature re-enables both
program and erase operations in previously pro-
tected sectors.
Sector protection/unprotection must be implemented
using programming equipment. The procedure re-
quires a high voltage (VID) on address pin A9 and the
control pins. Details on this method are provided in the
supplements, publication numbers 20819 and 21183.
Am29F002/Am29F002N
9
P R E L I M I N A R Y
Contact an AMD representative to obtain a copy of the
appropriate document.
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to the Command Defi-
nitions table). In addition, the following hardware data
protection measures prevent accidental erasure or pro-
gramming, which might otherwise be caused by spuri-
ous system level signals during VCC power-up and
power-down transitions, or from system noise.
The device is shipped with all sectors unprotected.
AMD offers the option of programming and protecting
sectors at its factory prior to shipping the device
through AMD’s ExpressFlash™ Service. Contact an
AMD representative for details.
It is possible to determine whether a sector is protected
or unprotected. See “Autoselect Mode” for details.
Low V
Write Inhibit
CC
Temporary Sector Unprotect
When VCC is less than VLKO, the device does not ac-
cept any write cycles. This protects data during VCC
power-up and power-down. The command register and
all internal program/erase circuits are disabled, and the
device resets. Subsequent writes are ignored until VCC
is greater than VLKO. The system must provide the
proper signals to the control pins to prevent uninten-
Note: This feature requites the RESET# pin and is
therefore not available on the Am29F002N.
This feature allows temporary unprotection of previ-
ously protected sectors to change data in-system.
The Sector Unprotect mode is activated by setting the
RESET# pin to VID. During this mode, formerly pro-
tected sectors can be programmed or erased by se-
lecting the sector addresses. Once VID is removed
from the RESET# pin, all the previously protected
sectors are protected again. Figure 1 shows the algo-
rithm, and the Temporary Sector Unprotect diagram
shows the timing waveforms, for this feature.
tional writes when VCC is greater than VLKO
.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or
WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# =
VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a
logical one.
START
Power-Up Write Inhibit
RESET# = V
(Note 1)
ID
If WE# = CE# = VIL and OE# = VIH during power up, the
device does not accept commands on the rising edge
of WE#. The internal state machine is automatically
reset to reading array data on power-up.
Perform Erase or
Program Operations
RESET# = V
IH
Temporary Sector
Unprotect
Completed (Note 2)
20818C-4
Notes:
1. All protected sectors unprotected.
2. All previously protected sectors are protected once
again.
Figure 1. Temporary Sector Unprotect Operation
10
Am29F002/Am29F002N
P R E L I M I N A R Y
COMMAND DEFINITIONS
Writing specific address and data commands or se-
quences into the command register initiates device op-
erations. The Command Definitions table defines the
valid register command sequences. Writing incorrect
address and data values or writing them in the im-
proper sequence resets the device to reading array
data.
however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the se-
quence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command must
be written to return to reading array data (also applies
to autoselect during Erase Suspend).
All addresses are latched on the falling edge of WE# or
CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the appropriate timing diagrams in the
“AC Characteristics” section.
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to read-
ing array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and devices codes,
and determine whether or not a sector is protected.
The Command Definitions table shows the address
and data requirements. This method is an alternative to
that shown in the Autoselect Codes (High Voltage
Method) table, which is intended for PROM program-
mers and requires VID on address bit A9.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array
data after completing an Embedded Program or Em-
bedded Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data.
After completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See “Erase Sus-
pend/Erase Resume Commands” for more information
on this mode.
The autoselect command sequence is initiated by
writing two unlock cycles, followed by the autoselect
command. The device then enters the autoselect
mode, and the system may read at any address any
number of times, without initiating another command
sequence.
A read cycle at address XX00h or retrieves the manu-
facturer code. A read cycle at address XX01h returns
the device code. A read cycle containing a sector ad-
dress (SA) and the address 02h in returns 01h if that
sector is protected, or 00h if it is unprotected. Refer to
the Sector Address tables for valid sector addresses.
The system must issue the reset command to re-en-
able the device for reading array data if DQ5 goes high,
or while in the autoselect mode. See the “Reset Com-
mand” section, next.
The system must write the reset command to exit the
autoselect mode and return to reading array data.
See also “Requirements for Reading Array Data” in the
“Device Bus Operations” section for more information.
The Read Operations table provides the read parame-
ters, and Read Operation Timings diagram shows the
timing diagram.
Byte Program Command Sequence
Programming is a four-bus-cycle operation. The pro-
gram command sequence is initiated by writing two un-
lock write cycles, followed by the program set-up
command. The program address and data are written
next, which in turn initiate the Embedded Program al-
gorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally generated program pulses and verify the pro-
grammed cell margin. The Command Definitions take
shows the address and data requirements for the byte
program command sequence.
Reset Command
Writing the reset command to the device resets the de-
vice to reading array data. Address bits are don’t care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ig-
nores reset commands until the operation is complete.
When the Embedded Program algorithm is complete,
the device then returns to reading array data and ad-
dresses are no longer latched. The system can deter-
mine the status of the program operation by using DQ7
or DQ6. See “Write Operation Status” for information
on these status bits.
The reset command may be written between the se-
quence cycles in a program command sequence be-
fore programming begins. This resets the device to
reading array data (also applies to programming in
Erase Suspend mode). Once programming begins,
Am29F002/Am29F002N
11
P R E L I M I N A R Y
Any commands written to the device during the Em-
command, which in turn invokes the Embedded Erase
algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algo-
rithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any con-
trols or timings during these operations. The Command
Definitions table shows the address and data require-
ments for the chip erase command sequence.
bedded Program Algorithm are ignored. On the
Am29F002 only, note that a hardware reset during the
sector erase operation immediately terminates the op-
eration. The Sector Erase command sequence should
be reinitiated once the device has returned to reading
array data, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
from a “0” back to a “1”. Attempting to do so may halt
the operation and set DQ5 to “1”, or cause the Data#
Polling algorithm to indicate the operation was suc-
cessful. However, a succeeding read will show that the
data is still “0”. Only erase operations can convert a “0”
to a “1”.
Any commands written to the chip during the Embed-
ded Erase algorithm are ignored. On the Am29F002
only, note that a hardware reset during the sector
erase operation immediately terminates the operation.
The Sector Erase command sequence should be rein-
itiated once the device has returned to reading array
data, to ensure data integrity.
The system can determine the status of the erase
operation by using DQ7, DQ6, or DQ2. See “Write
Operation Status” for information on these status
bits. When the Embedded Erase algorithm is com-
plete, the device returns to reading array data and
addresses are no longer latched.
START
Write Program
Command Sequence
Figure 3 illustrates the algorithm for the erase opera-
tion. See the Erase/Program Operations tables in “AC
Characteristics” for parameters, and to the Chip/Sector
Erase Operation Timings for timing waveforms.
Data Poll
from System
Embedded
Program
algorithm
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector
erase command sequence is initiated by writing two un-
lock cycles, followed by a set-up command. Two addi-
tional unlock write cycles are then followed by the
address of the sector to be erased, and the sector
erase command. The Command Definitions table
shows the address and data requirements for the sec-
tor erase command sequence.
in progress
Verify Data?
No
Yes
No
Increment Address
Last Address?
Yes
The device does not require the system to preprogram
the memory prior to erase. The Embedded Erase algo-
rithm automatically programs and verifies the sector for
an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or tim-
ings during these operations.
Programming
Completed
20818C-5
After the command sequence is written, a sector erase
time-out of 50 µs begins. During the time-out period,
additional sector addresses and sector erase com-
mands may be written. Loading the sector erase buffer
may be done in any sequence, and the number of sec-
tors may be from one sector to all sectors. The time be-
tween these additional cycles must be less than 50 µs,
otherwise the last address and command might not be
accepted, and erasure may begin. It is recommended
that processor interrupts be disabled during this time to
ensure all commands are accepted. The interrupts can
be re-enabled after the last Sector Erase command is
written. If the time between additional sector erase
Note: See the appropriate Command Definitions table for
program command sequence.
Figure 2. Program Operation
Chip Erase Command Sequence
Chip erase is a six-bus-cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
12
Am29F002/Am29F002N
P R E L I M I N A R Y
commands can be assumed to be less than 50 µs, the
system need not monitor DQ3. Any command other
than Sector Erase or Erase Suspend during the
time-out period resets the device to reading array
data. The system must rewrite the command sequence
and any additional sector addresses and commands.
START
Write Erase
Command Sequence
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising
edge of the final WE# pulse in the command sequence.
Data Poll
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. On the Am29F002 only, note that a hard-
ware reset during the sector erase operation immedi-
ately terminates the operation. The Sector Erase
command sequence should be reinitiated once the de-
vice has returned to reading array data, to ensure data
integrity.
from System
Embedded
Erase
algorithm
in progress
No
Data = FFh?
Yes
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the sta-
tus of the erase operation by using DQ7, DQ6, or DQ2.
Refer to “Write Operation Status” for information on
these status bits.
Erasure Completed
20818C-6
Notes:
1. See the appropriate Command Definitions table for erase
command sequence.
Figure 3 illustrates the algorithm for the erase opera-
tion. Refer to the Erase/Program Operations tables in
the “AC Characteristics” section for parameters, and to
the Sector Erase Operations Timing diagram for timing
waveforms.
2. See “DQ3: Sector Erase Timer” for more information.
Figure 3. Erase Operation
Am29F002/Am29F002N
13
P R E L I M I N A R Y
tors produces status data on DQ7–DQ0. The system
Erase Suspend/Erase Resume Commands
can use DQ7, or DQ6 and DQ2 together, to determine
if a sector is actively erasing or is erase-suspended.
See “Write Operation Status” for information on these
status bits.
The Erase Suspend command allows the system to in-
terrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure. This command is valid only during the sector
erase operation, including the 50 µs time-out period
during the sector erase command sequence. The
Erase Suspend command is ignored if written during
the chip erase operation or Embedded Program algo-
rithm. Writing the Erase Suspend command during the
Sector Erase time-out immediately terminates the
time-out period and suspends the erase operation. Ad-
dresses are “don’t-cares” when writing the Erase Sus-
pend command.
After an erase-suspended program operation is com-
plete, the system can once again read array data within
non-suspended sectors. The system can determine
the status of the program operation using the DQ7 or
DQ6 status bits, just as in the standard program oper-
ation. See “Write Operation Status” for more informa-
tion.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend
mode. The device allows reading autoselect codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the autoselect mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation. See “Autoselect Command Sequence”
for more information.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 µs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately ter-
minates the time-out period and suspends the erase
operation.
After the erase operation has been suspended, the
system can read array data from or program data to
any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Normal
read and write timings and command definitions apply.
Reading at any address within erase-suspended sec-
The system must write the Erase Resume command
(address bits are “don’t care”) to exit the erase suspend
mode and continue the sector erase operation. Further
writes of the Resume command are ignored. Another
Erase Suspend command can be written after the de-
vice has resumed erasing.
14
Am29F002/Am29F002N
P R E L I M I N A R Y
Table 5. Am29F002/Am29F002N Command Definitions
Bus Cycles (Notes 2–4)
Command
Sequence
(Note 1)
First
Second
Third
Addr
Fourth
Fifth
Sixth
Addr Data Addr Data
Data Addr Data Addr Data Addr Data
Read (Note 5)
Reset (Note 6)
Manufacturer ID
1
1
4
RA
XXX
555
RD
F0
AA
2AA
2AA
55
55
555
555
90
90
X00
X01
01
Device ID,
4
4
555
555
AA
AA
B0
Top Boot Block
Auto-
select
Device ID,
2AA
2AA
55
55
555
555
90
90
X01
34
(Note 7) Bottom Boot Block
00
01
Sector Protect Verify
(Note 8)
(SA)
X02
4
555
AA
Program
4
6
6
1
1
555
555
AA
AA
AA
B0
30
2AA
2AA
2AA
55
55
55
555
555
555
A0
80
80
PA
PD
AA
AA
Chip Erase
555
555
2AA
2AA
55
55
555
SA
10
30
Sector Erase
555
Erase Suspend (Note 9)
Erase Resume (Note 10)
XXX
XXX
Legend:
X = Don’t care
PD = Data to be programmed at location PA. Data latches on the
rising edge of WE# or CE# pulse, whichever happens first.
RA = Address of the memory location to be read.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A17–A13 uniquely select any sector.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed.
Addresses latch on the falling edge of the WE# or CE# pulse,
whichever happens later.
Notes:
1. See Table 1 for description of bus operations.
7. The fourth cycle of the autoselect command sequence is a
read cycle.
2. All values are in hexadecimal.
8. The data is 00h for an unprotected sector and 01h for a
protected sector. See “Autoselect Command Sequence” for
more information.
3. Except when reading array or autoselect data, all bus cycles
are write operations.
4. Address bits A17–A12 are don’t cares for unlock and
command cycles, except when PA or SA is required.
9. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend
mode. The Erase Suspend command is valid only during a
sector erase operation.
5. No unlock or command cycles required when reading array
data.
6. The Reset command is required to return to reading array
data when device is in the autoselect mode, or if DQ5 goes
high (while the device is providing status data).
10. The Erase Resume command is valid only during the Erase
Suspend mode.
Am29F002/Am29F002N
15
P R E L I M I N A R Y
WRITE OPERATION STATUS
The device provides several bits to determine the sta-
tus of a write operation: DQ2, DQ3, DQ5, DQ6, and
DQ7. Table 6 and the following subsections describe
the functions of these bits. DQ7 and DQ6 each offer a
method for determining whether a program or erase
operation is complete or in progress. These three bits
are discussed first.
START
Read DQ7–DQ0
Addr = VA
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host
system whether an Embedded Algorithm is in
progress or completed, or whether the device is in
Erase Suspend. Data# Polling is valid after the rising
edge of the final WE# pulse in the program or erase
command sequence.
Yes
DQ7 = Data?
No
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum pro-
grammed to DQ7. This DQ7 status also applies to pro-
gramming during Erase Suspend. When the
Embedded Program algorithm is complete, the device
outputs the datum programmed to DQ7. The system
must provide the program address to read valid status
information on DQ7. If a program address falls within a
protected sector, Data# Polling on DQ7 is active for ap-
proximately 2 µs, then the device returns to reading
array data.
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase al-
gorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
This is analogous to the complement/true datum output
described for the Embedded Program algorithm: the
erase function changes all the bits in a sector to “1”;
prior to this, the device outputs the “complement,” or
“0.” The system must provide an address within any of
the sectors selected for erasure to read valid status in-
formation on DQ7.
Yes
DQ7 = Data?
No
PASS
FAIL
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within any
sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Data# Polling
on DQ7 is active for approximately 100 µs, then the de-
vice returns to reading array data. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the se-
lected sectors that are protected.
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
20818C-7
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7–
Figure 4. Data# Polling Algorithm
following read cycles. This is because DQ7
DQ0 on the
may change asynchronously with DQ0–DQ6 while
Output Enable (OE#) is asserted low. The Data# Poll-
ing Timings (During Embedded Algorithms) figure in
the “AC Characteristics” section illustrates this.
Table 6 shows the outputs for Data# Polling on DQ7.
Figure 4 shows the Data# Polling algorithm.
16
Am29F002/Am29F002N
P R E L I M I N A R Y
trol the read cycles.) But DQ2 cannot distinguish
DQ6: Toggle Bit I
whether the sector is actively erasing or is erase-sus-
pended. DQ6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but
cannot distinguish which sectors are selected for era-
sure. Thus, both status bits are required for sector and
mode information. Refer to Table 6 to compare outputs
for DQ2 and DQ6.
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address, and is
valid after the rising edge of the final WE# pulse in the
command sequence (prior to the program or erase op-
eration), and during the sector erase time-out.
Figure 5 shows the toggle bit algorithm in flowchart
form, and the section “DQ2: Toggle Bit II” explains the
algorithm. See also the DQ6: Toggle Bit I subsection.
Refer to the Toggle Bit Timings figure for the toggle bit
timing diagram. The DQ2 vs. DQ6 figure shows the dif-
ferences between DQ2 and DQ6 in graphical form.
During an Embedded Program or Erase algorithm op-
eration, successive read cycles to any address cause
DQ6 to toggle. (The system may use either OE# or
CE# to control the read cycles.) When the operation is
complete, DQ6 stops toggling.
After an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 tog-
gles for approximately 100 µs, then returns to reading
array data. If not all selected sectors are protected,
the Embedded Erase algorithm erases the unpro-
tected sectors, and ignores the selected sectors that
are protected.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 5 for the following discussion. When-
ever the system initially begins reading toggle bit sta-
tus, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, a
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The sys-
tem can read array data on DQ7–DQ0 on the following
read cycle.
The system can use DQ6 and DQ2 together to deter-
mine whether a sector is actively erasing or is erase-
suspended. When the device is actively erasing (that is,
the Embedded Erase algorithm is in progress), DQ6
toggles. When the device enters the Erase Suspend
mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing
or erase-suspended. Alternatively, the system can use
DQ7 (see the subsection on DQ7: Data# Polling).
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the
system also should note whether the value of DQ5 is
high (see the section on DQ5). If it is, the system
should then determine again whether the toggle bit is
toggling, since the toggle bit may have stopped tog-
gling just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the
device did not complete the operation successfully, and
the system must write the reset command to return to
reading array data.
If a program address falls within a protected sector,
DQ6 toggles for approximately 2 µs after the program
command sequence is written, then returns to reading
array data.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Pro-
gram algorithm is complete.
The Write Operation Status table shows the outputs for
Toggle Bit I on DQ6. Refer to Figure 5 for the toggle bit
algorithm, and to the Toggle Bit Timings figure in the
“AC Characteristics” section for the timing diagram.
The DQ2 vs. DQ6 figure shows the differences be-
tween DQ2 and DQ6 in graphical form. See also the
subsection on DQ2: Toggle Bit II.
The remaining scenario is that the system initially de-
termines that the toggle bit is toggling and DQ5 has not
gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, de-
termining the status as described in the previous para-
graph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the
beginning of the algorithm when it returns to determine
the status of the operation (top of Figure 5).
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indi-
cates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit
II is valid after the rising edge of the final WE# pulse in
the command sequence.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions DQ5 produces a “1.” This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for era-
sure. (The system may use either OE# or CE# to con-
Am29F002/Am29F002N
17
P R E L I M I N A R Y
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously pro-
grammed to “0.” Only an erase operation can change
a “0” back to a “1.” Under this condition, the device
halts the operation, and when the operation has ex-
ceeded the timing limits, DQ5 produces a “1.”
START
Under both these conditions, the system must issue the
reset command to return the device to reading array
data.
Read DQ7–DQ0
Read DQ7–DQ0
(Note 1)
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase
command. When the time-out is complete, DQ3
switches from “0” to “1.” The system may ignore DQ3
if the system can guarantee that the time between ad-
ditional sector erase commands will always be less
than 50 µs. See also the “Sector Erase Command Se-
quence” section.
No
Toggle Bit
= Toggle?
Yes
No
DQ5 = 1?
Yes
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has ac-
cepted the command sequence, and then read DQ3. If
DQ3 is “1”, the internally controlled erase cycle has be-
gun; all further commands (other than Erase Suspend)
are ignored until the erase operation is complete. If
DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been ac-
cepted. Table 6 shows the outputs for DQ3.
(Notes
1, 2)
Read DQ7–DQ0
Twice
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1”. See text.
20818C-8
Figure 5. Toggle Bit Algorithm
18
Am29F002/Am29F002N
P R E L I M I N A R Y
Table 6. Write Operation Status
DQ7
DQ5
DQ2
Operation
(Note 1)
DQ7#
0
DQ6
(Note 2)
DQ3
N/A
1
(Note 1)
Embedded Program Algorithm
Embedded Erase Algorithm
Toggle
Toggle
0
0
No toggle
Toggle
Standard
Mode
Reading within Erase
Suspended Sector
1
No toggle
0
N/A
Toggle
Erase
Suspend
Mode
Reading within Non-Erase
Suspended Sector
Data
Data
Data
0
Data
N/A
Data
N/A
Erase-Suspend-Program
DQ7#
Toggle
Notes:
1. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
2. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
See “DQ5: Exceeded Timing Limits” for more information.
Am29F002/Am29F002N
19
P R E L I M I N A R Y
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C
20 ns
20 ns
+0.8 V
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . –55°C to +125°C
–0.5 V
–2.0 V
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . .–2.0 V to +7.0 V
A9, OE#, and
20 ns
RESET# (Note 2). . . . . . . . . . . .–2.0 V to +12.5 V
All other pins (Note 1) . . . . . . . . .–0.5 V to +7.0 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
20818C-9
Notes:
Figure 6. Maximum Negative Overshoot
Waveform
1. Minimum DC voltage on input or I/O pins is –0.5 V. During
voltage transitions, input or I/O pins may undershoot V
to –2.0 V for periods of up to 20 ns. See Figure 6.
SS
Maximum DC voltage on input or I/O pins is VCC +0.5 V.
During voltage transitions, input or I/O pins may overshoot
to V +2.0 V for periods up to 20 ns. See Figure 7.
CC
20 ns
2. Minimum DC input voltage on pins A9, OE#, and RESET#
is –0.5 V. During voltage transitions, A9, OE#, and
V
CC
RESET# may undershoot V to –2.0 V for periods of up
SS
+2.0 V
to 20 ns. See Figure 6. Maximum DC input voltage on pin
A9 is +12.5 V which may overshoot to +13.5 V for periods
up to 20 ns. (RESET# is not available on Am29F002N.)
V
CC
+0.5 V
2.0 V
3. No more than one output may be shorted to ground at a
time. Duration of the short circuit should not be greater
than one second.
20 ns
20 ns
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
20818C-10
Figure 7. Maximum Positive Overshoot
Waveform
OPERATING RANGES
Commercial (C) Devices
Ambient Temperature (TA) . . . . . . . . . . . 0°C to +70°C
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C
Extended (E) Devices
Ambient Temperature (TA) . . . . . . . . –55°C to +125°C
VCC Supply Voltages
VCC for ± 5% devices. . . . . . . . . . .+4.75 V to +5.25 V
VCC for ± 10% devices. . . . . . . . . . . .+4.5 V to +5.5 V
Operating ranges define those limits between which the func-
tionality of the device is guaranteed.
20
Am29F002/Am29F002N
P R E L I M I N A R Y
DC CHARACTERISTICS
TTL/NMOS Compatible
Parameter
Description
Test Conditions
= V to V , V = V
CC max
Min
Typ
Max
Unit
I
Input Load Current
V
±1.0
µA
LI
IN
SS
CC
CC
A9, OE#, RESET# Input Load Current
(Notes 1, 4)
V
= V
;
CC
CC max
I
50
µA
LIT
A9, OE#, RESET# = 12.5 V
= V to V , V = V
CC max
I
Output Leakage Current
V
±1.0
30
40
1
µA
mA
mA
mA
mA
V
LO
OUT
SS
CC CC
I
I
I
I
V
V
V
V
Active Read Current (Note 2)
Active Write Current (Notes 3, 4)
Standby Current
CE# = V OE#
V
20
30
CC1
CC2
CC3
CC4
CC
CC
CC
CC
IL,
=
=
IH
IH
CE# = V OE#
V
IL,
V
= V
= V
, CE#, OE# = V
IH
0.4
0.4
CC
CC
CC max
CC max
Reset Current (Note 1)
V
; RESET# = V
1
IL
V
Input Low Voltage
Input High Voltage
–0.5
2.0
0.8
IL
V
CC
V
V
V
V
IH
+ 0.5
12.5
0.45
Voltage for Autoselect and Temporary
Sector Unprotect
V
= 5.0 V
11.5
ID
CC
V
Output Low Voltage
Output High Voltage
I
I
= 12 mA, V = V
CC min
V
V
V
OL
OL
CC
V
= –2.5 mA, V = V
CC min
2.4
3.2
OH
OH
CC
V
Low V Lock-Out Voltage
4.2
LKO
CC
Notes:
1. RESET# is not available on Am29F002N.
2. The I current listed is typically less than 2 mA/MHz, with OE# at V
.
IH
CC
3. I active while Embedded Erase or Embedded Program is in progress.
CC
4. Not 100% tested.
Am29F002/Am29F002N
21
P R E L I M I N A R Y
Test Conditions
DC CHARACTERISTICS
CMOS Compatible
Parameter
Description
Min
Typ
Max
Unit
V
V
= V to V
,
IN
SS
CC
I
Input Load Current
±1.0
µA
LI
= V
CC
CC max
A9, OE#, RESET#
Input Load Current (Notes 1, 4) A9, OE#, RESET# = 12.5 V
V
= V
;
CC max
CC
I
50
±1.0
30
µA
µA
LIT
V
V
= V to V
= V
,
CC
OUT
CC
SS
I
Output Leakage Current
Active Read Current
LO
CC max
V
CC
I
I
CE# = V OE#
V
V
20
30
mA
mA
CC1
CC2
IL,
=
=
IH
(Note 2)
V
Active Write Current
CC
CE# = V OE#
40
IL,
IH
(Notes 3, 4)
I
I
V
V
Standby Current (Note 5)
Reset Current (Notes 1, 5)
V
V
= V
= V
; CE# = V ±0.5 V
1
1
5
5
µA
µA
V
CC3
CC4
CC
CC
CC
CC max
CC
; RESET# = V
CC
CC max
IL
V
Input Low Voltage
Input High Voltage
–0.5
0.8
IL
V
V
0.7 x V
V + 0.3
CC
V
IH
CC
Voltage for Autoselect and
Temporary Sector Unprotect
V
= 5.0 V
11.5
12.5
0.45
V
ID
CC
V
Output Low Voltage
I
I
I
= 12 mA, V = V
CC min
V
V
OL
OL
OH
OH
CC
V
= –2.5 mA, V = V
CC min
0.85 V
OH1
OH2
CC
CC
Output High Voltage
V
= –100 µA, V = V
V
–0.4
CC
CC min
CC
V
Low V Lock-Out Voltage
3.2
4.2
V
LKO
CC
Notes:
1. RESET# is not available on Am29F002N.
2. The I current listed is typically less than 2 mA/MHz, with OE# at V
.
IH
CC
3. I active while Embedded Erase or Embedded Program is in progress.
CC
4. Not 100% tested.
5. I
and I
= 20 µA max at extended temperature (>+85° C).
CC3
CC4
22
Am29F002/Am29F002N
P R E L I M I N A R Y
TEST CONDITIONS
Table 7. Test Specifications
All
5.0 V
Test Condition
-55
others
Unit
2.7 kΩ
Device
Under
Test
Output Load
1 TTL gate
Output Load Capacitance, C
(including jig capacitance)
L
30
5
100
20
pF
C
L
6.2 kΩ
Input Rise and Fall Times
Input Pulse Levels
ns
0.0–3.0 0.45–2.4
V
Input timing measurement
reference levels
1.5
1.5
0.8, 2.0
0.8, 2.0
V
V
Note: Diodes are IN3064 or equivalent
Output timing measurement
reference levels
20818C-11
Figure 8. Test Setup
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
Don’t Care, Any Change Permitted
Does Not Apply
Changing, State Unknown
Center Line is High Impedance State (High Z)
KS000010-PAL
Am29F002/Am29F002N
23
P R E L I M I N A R Y
AC CHARACTERISTICS
Read Operations
Parameter
Speed Option
JEDEC
Std
Description
Test Setup
-55
-70
-90
-120
Unit
t
t
Read Cycle Time (Note 1)
Min
55
70
90
120
ns
AVAV
RC
CE# = V
OE# = V
IL
IL
t
t
Address to Output Delay
Max
55
70
90
120
ns
AVQV
ACC
t
t
t
Chip Enable to Output Delay
OE# = V
Max
Max
Max
55
30
15
70
30
20
90
35
20
120
50
ns
ns
ns
ELQV
GLQV
EHQZ
CE
IL
t
t
Output Enable to Output Delay
Chip Enable to Output High Z (Note 1)
OE
t
30
DF
DF
Output Enable to Output High Z
(Note 1)
t
t
Max
Min
Min
15
20
20
30
ns
ns
ns
GHQZ
Read
0
Output Enable
t
Hold Time
(Note 1)
OEH
Toggle and
Data# Polling
10
Output Hold Time From Addresses, CE#
or OE#, Whichever Occurs First (Note 1)
t
t
Min
0
ns
AXQX
OH
Notes:
1. Not 100% tested.
2. See Figure 8 and Table 7 for test specifications.
tRC
Addresses Stable
tACC
Addresses
CE#
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Output Valid
Outputs
RESET#
n/a Am29F002N
20818C-12
Figure 9. Read Operations Timings
24
Am29F002/Am29F002N
P R E L I M I N A R Y
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std Description
RESET# Pin Low (During Embedded
Test Setup
All Speed Options
Unit
t
Max
20
µs
READY
Algorithms) to Read or Write (See Note)
RESET# Pin Low (NOT During Embedded
Algorithms) to Read or Write (See Note)
t
Max
500
ns
READY
t
t
RESET# Pulse Width
Min
Min
500
50
ns
ns
RP
RESET# High Time Before Read (See Note)
RH
Note: Not 100% tested. RESET# is not available on Am29F002N.
CE#, OE#
tRH
RESET#
n/a Am29F002N
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
RESET#
n/a Am29F002N
tRP
20818C-13
Figure 10. RESET# Timings
25
Am29F002/Am29F002N
P R E L I M I N A R Y
AC CHARACTERISTICS
Erase/Program Operations
Parameter
JEDEC
Std.
Description
-55
-70
-90
-120
Unit
ns
t
t
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
Data Setup Time
Min
Min
Min
Min
Min
Min
55
70
90
120
AVAV
WC
t
t
0
ns
AVWL
WLAX
AS
AH
DS
DH
t
t
45
25
45
30
45
45
50
50
ns
t
t
ns
DVWH
WHDX
t
t
Data Hold Time
0
0
ns
t
Output Enable Setup Time
ns
OES
Read Recovery Time Before Write
(OE# High to WE# Low)
t
t
Min
0
ns
GHWL
GHWL
t
t
CE# Setup Time
Min
Min
Min
Min
Typ
Typ
Min
0
0
ns
ns
ELWL
WHEH
WLWH
WHWL
CS
CH
WP
t
t
t
CE# Hold Time
t
Write Pulse Width
30
35
45
50
ns
t
t
Write Pulse Width High
Programming Operation (Note 2)
Sector Erase Operation (Note 2)
20
7
ns
WPH
t
t
µs
WHWH1
WHWH2
WHWH1
WHWH2
t
t
1
sec
µs
t
V
Setup Time (Note 1)
50
VCS
CC
Notes:
1. Not 100% tested.
2. See the “Erase and Programming Performance” section for more information.
Am29F002/Am29F002N
26
P R E L I M I N A R Y
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
Read Status Data (last two cycles)
tAS
PA
tWC
Addresses
555h
PA
PA
tAH
CE#
OE#
tCH
tGHWL
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
DOUT
A0h
Status
Data
VCC
tVCS
Notes:
1. PA = program address, PD = program data, D
is the true data at the program address.
OUT
20818C-14
Figure 11. Program Operation Timings
27
Am29F002/Am29F002N
P R E L I M I N A R Y
AC CHARACTERISTICS
Erase Command Sequence (last two cycles)
Read Status Data
VA
tAS
SA
tWC
VA
Addresses
CE#
2AAh
555h for chip erase
tAH
tGHWL
tCH
OE#
tWP
WE#
tWPH
tWHWH2
tCS
tDS
tDH
In
Data
VCC
Complete
55h
30h
Progress
10 for Chip Erase
tVCS
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”).
20818C-15
Figure 12. Chip/Sector Erase Operation Timings
Am29F002/Am29F002N
28
P R E L I M I N A R Y
AC CHARACTERISTICS
tRC
VA
Addresses
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
WE#
tDF
tOH
High Z
High Z
DQ7
Valid Data
Complement
Complement
Status Data
True
DQ0–DQ6
Valid Data
Status Data
True
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
20818C-16
Figure 13. Data# Polling Timings (During Embedded Algorithms)
tRC
Addresses
CE#
VA
tACC
tCE
VA
VA
VA
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
DQ6/DQ2
Valid Status
(first read)
Valid Status
Valid Status
Valid Data
(second read)
(stops toggling)
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read
cycle, and array data read cycle.
20818C-17
Figure 14. Toggle Bit Timings (During Embedded Algorithms)
29
Am29F002/Am29F002N
P R E L I M I N A R Y
AC CHARACTERISTICS
Enter
Embedded
Erasing
Erase
Suspend
Enter Erase
Suspend Program
Erase
Resume
Erase
Erase Suspend
Read
Erase
Suspend
Program
Erase
Complete
WE#
Erase
Erase Suspend
Read
DQ6
DQ2
Note: The system may use CE# or OE# to toggle DQ2 and DQ6. DQ2 toggles only when read at an address within an
erase-suspended sector.
20818C-18
Figure 15. DQ2 vs. DQ6
Temporary Sector Unprotect (Am29F002 only)
Parameter
JEDEC Std.
Description
Rise and Fall Time (See Note)
All Speed Options
Unit
t
V
Min
Min
500
ns
VIDR
ID
RESET# Setup Time for Temporary Sector
Unprotect
t
4
µs
RSP
Note: Not 100% tested.
12 V
RESET#
0 or 5 V
0 or 5 V
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRSP
20818C-19
Figure 16. Temporary Sector Unprotect Timing Diagram (Am29F002 only)
Am29F002/Am29F002N
30
P R E L I M I N A R Y
AC CHARACTERISTICS
Alternate CE# Controlled Erase/Program Operations
Parameter
JEDEC
Std.
Description
-55
-70
-90
-120
Unit
ns
t
t
t
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
Data Setup Time
Min
Min
Min
Min
Min
Min
55
70
90
120
AVAV
AVEL
ELAX
DVEH
EHDX
WC
t
0
ns
AS
AH
DS
DH
t
t
45
25
45
30
45
45
50
50
ns
t
t
ns
t
t
Data Hold Time
0
0
ns
t
Output Enable Setup Time
ns
OES
Read Recovery Time Before Write
(OE# High to WE# Low)
t
t
t
Min
0
ns
GHEL
WLEL
GHEL
t
t
WE# Setup Time
Min
Min
Min
Min
Typ
Typ
0
0
ns
ns
WS
t
WE# Hold Time
EHWH
WH
t
t
CE# Pulse Width
30
35
45
50
ns
ELEH
EHEL
CP
t
t
CE# Pulse Width High
Programming Operation (Note 2)
Sector Erase Operation (Note 2)
20
7
ns
CPH
t
t
µs
WHWH1
WHWH2
WHWH1
WHWH2
t
t
1
sec
1. Not 100% tested.
2. See the “Erase and Programming Performance” section for more information.
31
Am29F002/Am29F002N
P R E L I M I N A R Y
AC CHARACTERISTICS
555 for program
PA for program
2AA for erase
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tWH
tAS
tAH
WE#
OE#
tGHEL
tWHWH1 or 2
tCP
CE#
tWS
tCPH
tDS
tDH
DQ7#
DOUT
Data
tRH
A0 for program
55 for erase
PD for program
30 for sector erase
10 for chip erase
RESET#
Notes:
1. PA = Program Address, PD = Program Data, DQ7# = complement of data written to device, D
= data written to device.
20818C-20
OUT
2. Figure indicates the last two bus cycles of the command sequence.
Figure 17. Alternate CE# Controlled Write Operation Timings
Am29F002/Am29F002N
32
P R E L I M I N A R Y
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Typ (Note 1)
Max (Note 2)
Unit
s
Comments
Sector Erase Time
1
7
8
Excludes 00h programming
prior to erasure (Note 4)
Chip Erase Time
s
Byte Programming Time
Chip Programming Time (Note 3)
7
300
µs
s
Excludes system level
overhead (Note 5)
1.8
5.4
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 5.0 V V , 100,000 cycles. Additionally,
CC
programming typicals assume checkerboard pattern.
2. Under worst case conditions of 90°C, V = 4.5 V (4.75 V for -55), 100,000 cycles.
CC
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
program faster than the maximum program times listed.
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the four-bus-cycle sequence for the program command. See Table 5
for further information on command definitions.
6. The device has a minimum guaranteed erase and program cycle endurance of 100,000 cycles.
LATCHUP CHARACTERISTICS
Description
Min
Max
Input voltage with respect to V on all pins except I/O pins
(including A9, OE#, and RESET#)
SS
–1.0 V
12.5 V
Input voltage with respect to V on all I/O pins
–1.0 V
V
+ 1.0 V
CC
SS
V
Current
–100 mA
+100 mA
CC
Note: Includes all pins except V . Test conditions: V = 5.0 V, one pin at a time. RESET# not available on Am29F002N.
CC
CC
TSOP PIN CAPACITANCE
Parameter
Symbol
Parameter Description
Test Setup
= 0
Typ
6
Max
7.5
12
Unit
pF
C
Input Capacitance
Output Capacitance
V
IN
IN
C
V
= 0
8.5
7.5
pF
OUT
OUT
C
Control Pin Capacitance
V
= 0
IN
9
pF
IN2
Notes:
1. Sampled, not 100% tested.
2. Test conditions T = 25°C, f = 1.0 MHz.
A
33
Am29F002/Am29F002N
P R E L I M I N A R Y
PLCC AND PDIP PIN CAPACITANCE
Parameter
Symbol
Parameter Description
Input Capacitance
Test Conditions
Typ
4
Max
6
Unit
pF
C
V
V
V
= 0
IN
IN
C
Output Capacitance
= 0
= 0
8
12
12
pF
OUT
OUT
C
Control Pin Capacitance
8
pF
IN2
PP
Notes:
1. Sampled, not 100% tested.
2. Test conditions T = 25°C, f = 1.0 MHz.
A
DATA RETENTION
Parameter
Test Conditions
150°C
Min
10
Unit
Years
Years
Minimum Pattern Data Retention Time
125°C
20
Am29F002/Am29F002N
34
P R E L I M I N A R Y
PHYSICAL DIMENSIONS
PD 032
32-Pin Plastic DIP (measured in inches)
1.640
1.670
.600
.625
17
16
32
.009
.015
.530
.580
Pin 1 I.D.
.630
.700
.045
.065
0°
10°
.005 MIN
.140
.225
16-038-S_AG
PD 032
EC75
SEATING PLANE
.090
.110
.015
.060
.016
.022
5-28-97 lv
.120
.160
PL 032
32-Pin Plastic Leaded Chip Carrier (measured in inches)
.485
.495
.447
.453
.009
.015
.042
.056
.125
.140
.585
.595
Pin 1 I.D.
.080
.095
.547
.553
SEATING
PLANE
.400
REF.
.490
.530
.013
.021
.050 REF.
16-038FPO-5
PL 032
DA79
.026
.032
TOP VIEW
SIDE VIEW
6-28-94 ae
35
Am29F002/Am29F002N
P R E L I M I N A R Y
PHYSICAL DIMENSIONS (continued)
TS 032
32-Pin Standard Thin Small Package (measured in millimeters)
0.95
1.05
Pin 1 I.D.
1
7.90
8.10
0.50 BSC
0.05
0.15
18.30
18.50
19.80
20.20
0.08
0.20
0.10
0.21
16-038-TSOP-2
TS 032
DA95
1.20
MAX
3-25-97 lv
0°
5°
0.50
0.70
Am29F002/Am29F002N
36
P R E L I M I N A R Y
REVISION SUMMARY FOR AM29F002/AM29F002N
DC Characteristics
Revision C
Added Note 4 reference to ILIT. Corrected maximum
currents for ICC1 and ICC2, typical currents for ICC3 and
Global
Made formatting and layout consistent with other data
sheets. Used updated common tables and diagrams.
Combined Am29F002 and Am29F002N into a single
data sheet.
ICC4, test conditions for ICC4 and VOL
.
In TTL/NMOS table, deleted Note 5.
In CMOS table, corrected IOH current for VOH
.
Revision C+1
AC Characteristics
Figure 17, Alternate CE# Controlled Write
Operations Timings
Read Operations: Corrected tDF specifications for -55
speed option.
Removed the RY/BY# waverform and tBUSY parameter.
The RY/BY# pin is not available on this device.
Erase/Program Operations: Corrected the notes refer-
ence for tWHWH1 and tWHWH2. These parameters are
100% tested. Corrected the note reference for tVCS
.
Revision C+2
This parameter is not 100% tested. Removed -150
specifications. Corrected tDS and tWP for -55 speed op-
tion, tAH for -90 speed option.
Block Diagram
Corrected diagram by adding paths from the timer to
the PGM and Erase Voltage Generators.
Alternate CE# Controlled Erase/Program Operations:
Corrected the notes reference for tWHWH1 and tWHWH2
.
Table 3, Bottom Boot Block Sector Addresses
These parameters are 100% tested. This parameter is
not 100% tested. Removed -150 specifications. Cor-
rected tDS and tCP for -55 speed option.
Corrected adddress bit A15 for sector SA2 to “0.”
Table 5, Command Definitions
Deleted the lower row of addresses in the Sector Pro-
tect Verify command definitions.
Temporary Sector Unprotect Table
Added note reference for tVIDR. This parameter is not
100% tested.
In the legend, corrected the definition for SA to indicate
that address bits A17–A13 uniquely select a sector.
Deleted Note 4.
Trademarks
Copyright © 1998 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
37
Am29F002/Am29F002N
AM29F002T-120EI 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
AM29F002T-120EIB | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120JC | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120JCB | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120JE | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120JEB | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120JI | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120JIB | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120PC | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120PCB | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 | |
AM29F002T-120PE | AMD | 2 Megabit (256 K x 8-Bit) CMOS 5.0 Volt-only Boot Sector Flash Memory | 获取价格 |
AM29F002T-120EI 相关文章
- 2024-09-20
- 6
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6