MB15F73ULPFT [SPANSION]
PLL Frequency Synthesizer;
| 型号： | MB15F73ULPFT |
| 厂家： | 
SPANSION |
| 描述： | PLL Frequency Synthesizer 信息通信管理 光电二极管 |
| 文件： | 总29页 (文件大小：738K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Spansion® Analog and Microcontroller
Products
The following document contains information on Spansion analog and microcontroller products. Although the
document is marked with the name “Fujitsu”, the company that originally developed the specification, Spansion
will continue to offer these products to new and existing customers.
Continuity of Specifications
There is no change to this document as a result of offering the device as a Spansion product. Any changes that
have been made are the result of normal document improvements and are noted in the document revision
summary, where supported. Future routine revisions will occur when appropriate, and changes will be noted in a
revision summary.
Continuity of Ordering Part Numbers
Spansion continues to support existing part numbers beginning with “MB”. To order these products, please use
only the Ordering Part Numbers listed in this document.
For More Information
Please contact your local sales office for additional information about Spansion memory, analog, and
microcontroller products and solutions.
FUJITSU SEMICONDUCTOR
DATA SHEET
DS04–21368–2E
ASSP
Dual Serial Input
PLL Frequency Synthesizer
MB15F73UL
■ DESCRIPTION
The Fujitsu Semiconductor MB15F73UL is a serial input Phase Locked Loop (PLL) frequency synthesizer
with a 2250 MHz and a 600 MHz prescalers. A 64/65 or a 128/129 for the 2250 MHz prescaler, and a 8/9
or a 16/17 for the 600 MHz prescaler can be selected for the prescaler that enables pulse swallow operation.
The BiCMOS process is used, as a result a supply current is typically 3.2 mA at 2.7 V. The supply voltage
range is from 2.4 V to 3.6 V. A refined charge pump supplies well-balanced output current with 1.5 mA and
6 mA selectable by serial date. The data format is the same as the previous one MB15F03SL, MB15F73SP.
Fast locking is achieved for adopting the new circuit.
■ FEATURES
• High frequency operation
: RF synthesizer : 2250 MHz Max.
: IF synthesizer : 600 MHz Max.
: VCC = 2.4 to 3.6 V
• Low power supply voltage
• Ultra low power supply current : ICC = 3.2 mA Typ.
(VCC = Vp = 2.7 V, Ta = +25 °C, SWIF = SWRF = 0 in IF/RF locking state)
• Direct power saving function : Power supply current in power saving mode
Typ. 0.1 μA (VCC = Vp = 2.7 V, Ta = +25 °C)
Max. 10 μA (VCC = Vp = 2.7 V)
• Software selectable charge pump current : 1.5 mA/6.0 mA Typ.
• Dual modulus prescaler : 2250 MHz prescaler (64/65 or128/129) /600 MHz prescaler (8/9 or 16/17)
• 23 bit shift register
• Serial input binary 14-bit programmable reference divider : R = 3 to 16,383
• Serial input programmable divider consisting of:
- Binary 7-bit swallow counter : 0 to 127
- Binary 11-bit programmable counter : 3 to 2,047
• Built-in high-speed tuning, low-noise phase comparator, current-switching type constant current circuit
• On-chip phase control for phase comparator
• On-chip phase comparator for fast lock and low noise
• Built-in digital locking detector circuit to detect PLL locking and unlocking
• Operating temperature : Ta = −40 °C to +85 °C
Copyright©2001-2012 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
2012.5
MB15F73UL
■ PIN ASSIGNMENTS
(TSSOP-20)
TOP VIEW
(QFN-20)
TOP VIEW
19 18 17 16
20
1
2
OSCIN
GND
finIF
20
19
18
17
16
15
14
13
12
11
Clock
Data
finRF
finIF
XfinIF
GNDIF
VCCIF
PSIF
15
14
13
12
11
1
2
3
4
5
3
LE
XfinRF
GNDRF
4
XfinIF
GNDIF
VCCIF
PSIF
finRF
5
XfinRF
GNDRF
VCCRF
PSRF
VpRF
DoRF
6
V
CCRF
7
PSRF
8
VpIF
9
DoIF
6
7
8
9
10
10
LD/fout
(LCC-20P-M63)
(FPT-20P-M06)
2
DS04–21368–2E
MB15F73UL
■ PIN DESCRIPTION
Pin no.
Pin
I/O
Descriptions
name
TSSOP QFN
The programmable reference divider input pin. TCXO should be connected
with an AC coupling capacitor.
1
2
3
19
20
1
OSCIN
GND
finIF
I
⎯
I
Ground pin for OSC input buffer and the shift register circuit.
Prescaler input pin for the IF-PLL.
Connection to an external VCO should be AC coupling.
Prescaler complimentary input for the IF-PLL section.
This pin should be grounded via a capacitor.
4
5
6
2
3
4
XfinIF
GNDIF
VCCIF
I
⎯
⎯
Ground pin for the IF-PLL section.
Power supply voltage input pin for the IF-PLL section (except for the charge
pump circuit) , the shift register and the oscillator input buffer.
Power saving mode control pin for the IF-PLL section. This pin must be set at
“L” when the power supply is started up. (Open is prohibited.)
PSIF = “H” ; Normal mode/PSIF = “L” ; Power saving mode
7
5
PSIF
I
8
9
6
7
VpIF
DoIF
⎯
Power supply voltage input pin for the IF-PLL charge pump.
Charge pump output for the IF-PLL section.
O
Lock detect signal output (LD) /phase comparator monitoring output (fout)
pin. The output signal is selected by LDS bit in a serial data.
10
8
LD/fout
O
LDS bit = “H” ; outputs fout signal/LDS bit = “L” ; outputs LD signal
11
12
9
DoRF
VpRF
O
Charge pump output for the RF-PLL section.
10
⎯
Power supply voltage input pin for the RF-PLL charge pump.
Power saving mode control for the RF-PLL section. This pin must be set at
“L” when the power supply is started up. (Open is prohibited. )
PSRF = “H” ; Normal mode/PSRF = “L” ; Power saving mode
13
11
PSRF
I
Power supply voltage input pin for the RF-PLL section (except for the charge
pump circuit)
14
15
16
12
13
14
VCCRF
GNDRF
XfinRF
⎯
⎯
I
Ground pin for the RF-PLL section
Prescaler complimentary input pin for the RF-PLL section.
This pin should be grounded via a capacitor.
Prescaler input pin for the RF-PLL.
Connection to an external VCO should be via AC coupling.
17
18
15
16
finRF
LE
I
I
Load enable signal input pin (with the schmitt trigger circuit)
When LE is set “H”, data in the shift register is transferred to the correspond-
ing latch according to the control bit in a serial data.
Serial data input pin (with the schmitt trigger circuit)
Data is transferred to the corresponding latch (IF-ref. counter, IF-prog.
counter, RF-ref. counter, RF-prog. counter) according to the control bit in a
serial data.
19
20
17
18
Data
I
I
Clock input pin for the 23-bit shift register (with the schmitt trigger circuit)
One bit data is shifted into the shift register on a rising edge of the clock.
Clock
DS04–21368–2E
3
MB15F73UL
■ BLOCK DIAGRAM
VpIF
VCCIF GNDIF
(3)
(6)
(4)
6
5
8
Intermittent
mode control
(IF-PLL)
3 bit latch
PSIF 7
7 bit latch
Binary 7-bit
11 bit latch
Binary 11-bit
(5)
Phase
comp.
(IF-PLL)
Charge
pump
(IF-PLL)
9
(7)
DoIF
Current
Switch
swallow counter programmable
(IF-PLL)
counter (IF-PLL)
fpIF
finIF 3
(1)
XfinIF 4
(2)
Prescaler
(IF-PLL)
(8/9, 16/17)
Lock Det.
(IF-PLL)
2 bit latch
14 bit latch
1 bit latch
LDIF
Binary 14-bit pro-
grammable ref.
counter(IF-PLL)
C/P setting
counter
T1 T2
frIF
Fast
lock
Tuning
OSCIN 1
(19)
Selector
AND
frRF
LD
frIF
frRF
fpIF
fpRF
Binary 14-bit pro-
grammable ref.
counter (RF-PLL))
T1 T2
C/P setting
counter
10
(8) fout
LD/
OR
2 bit latch
14 bit latch
1 bit latch
LDRF
(15)
finRF 17
Prescaler
(RF-PLL)
(64/65, 128/129)
Lock Det.
(RF-PLL)
fpRF
XfinRF 16
(
14
)
Phase
comp.
(RF-PLL)
Charge
pump
(RF-PLL)
Binary 11-bit
programmable
counter (RF-PLL)
Binary 7-bit
swallow counter
(RF-PLL)
Current
Switch
11
(9)
DoRF
Intermittent
mode control
(RF-PLL)
PSRF 13
fpRF
3 bit latch
7 bit latch
11 bit latch
(11)
Schmitt
circuit
LE 18
(16)
Latch selector
(17)
Data 19
Schmitt
circuit
C
N
1
C
N
2
23-bit shift register
Schmitt
circuit
Clock 20
(18)
2 (20)
GND
(12) 14
VCCRF
15 (13)
GNDRF
12(10)
VpRF
O : TSSOP
( ) : QFN
4
DS04–21368–2E
MB15F73UL
■ ABSOLUTE MAXIMUM RATINGS
Rating
Parameter
Symbol
Unit
Min
−0.5
VCC
Max
VCC
Vp
4.0
4.0
V
V
Power supply voltage
Input voltage
VI
−0.5
GND
GND
−55
VCC + 0.5
VCC
V
LD/fout
Output voltage
VO
V
DoIF, DoRF
VDO
Tstg
Vp
V
Storage temperature
+125
°C
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
■ RECOMMENDED OPERATING CONDITIONS
Value
Parameter
Symbol
Unit
Remarks
Min
2.4
Typ
2.7
2.7
⎯
Max
3.6
VCC
Vp
VI
V
V
VCCRF = VCCIF
Power supply voltage
VCC
3.6
Input voltage
GND
−40
VCC
+85
V
Operating temperature
Ta
⎯
°C
Note : • VCCRF, VpRF, VCCIF and VpIF must supply equal voltage.
Even if either RF-PLL or IF-PLL is not used, power must be supplied to VCCRF, VpRF, VCCIF and VpIF
to keep them equal.
It is recommended that the non-use PLL is controlled by power saving function.
• Although this device contains an anti-static element to prevent electrostatic breakdown and the circuitry
has been improved in electrostatic protection, observe the following precautions when handling the
device.
• When storing and transporting the device, put it in a conductive case.
• Before handling the device, confirm the (jigs and) tools to be used have been uncharged (ground
ed) as well as yourself. Use a conductive sheet on working bench.
• Before fitting the device into or removing it from the socket, turn the power supply off.
• When handling (such as transporting) the device mounted board, protect the leads with a
conductive sheet.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of
the semiconductor device. All of the device's electrical characteristics are warranted when the
device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented
onthedatasheet.Usersconsideringapplicationoutsidethelistedconditionsareadvisedtocontact
their representatives beforehand.
DS04–21368–2E
5
MB15F73UL
*
■ ELECTRICAL CHARACTERISTICS
(VCC = 2.4 V to 3.6 V, Ta = −40 °C to +85 °C)
Value
Unit
Parameter
Symbol
Condition
Min
Typ
Max
finIF = 480 MHz
*1
ICCIF
0.8
1.2
1.7
mA
mA
VCCIF = VpIF = 2.7 V
Power supply current
finRF = 2000 MHz
VCCRF = VpRF = 2.7 V
*1
ICCRF
1.3
2.0
2.8
IPSIF
IPSRF
finIF
PSIF = PSRF = “L”
PSIF = PSRF = “L”
IF PLL
⎯
⎯
0.1*2
0.1*2
⎯
10
10
μA
Power saving current
Operating frequency
Input sensitivity
μA
*3
finIF
50
600
2250
40
MHz
MHz
MHz
dBm
dBm
VP−P
*3
finRF
finRF
fOSC
RF PLL
200
3
⎯
OSCIN
finIF
⎯
⎯
PfinIF
IF PLL, 50 Ω system
−15
−15
0.5
⎯
+2
finRF
PfinRF RF PLL, 50 Ω system
⎯
+2
Input available voltage OSCIN
VOSC
⎯
⎯
VCC
0.7 VCC
+ 0.4
“H” level input voltage
“L” level input voltage
VIH
Schmitt triger input
⎯
⎯
⎯
V
V
Data
LE
Clock
0.3 VCC
− 0.4
VIL
Schmitt triger input
⎯
“H” level input voltage
“L” level input voltage
VIH
⎯
⎯
0.7 VCC
⎯
⎯
⎯
V
V
PSIF
PSRF
VIL
⎯
0.3 VCC
*4
Data
LE
Clock
PS
“H” level input current
“L” level input current
IIH
⎯
⎯
−1.0
−1.0
⎯
⎯
+1.0
+1.0
μA
μA
*4
IIL
“H” level input current
“L” level input current
IIH
⎯
⎯
0
⎯
⎯
+100
μA
μA
OSCIN
*4
IIL
−100
0
VCC = Vp = 2.7 V,
IOH = −1 mA
VCC −
“H” level output voltage
“L” level output voltage
“H” level output voltage
“L” level output voltage
VOH
VOL
⎯
⎯
⎯
⎯
⎯
⎯
0.4
⎯
V
V
0.4
LD/
fout
VCC = Vp = 2.7 V,
IOL = 1 mA
⎯
Vp − 0.4
⎯
VCC = Vp = 2.7 V, I
DOH = −0.5 mA
VDOH
VDOL
IOFF
V
DoIF
DoRF
VCC = Vp = 2.7 V,
DOL = 0.5 mA
0.4
2.5
V
High impedance cutoff DoIF
current
VCC = Vp = 2.7 V
VOFF = 0.5 V to Vp − 0.5 V
⎯
nA
DoRF
*4
“H” level output current
“L” level output current
IOH
VCC = Vp = 2.7 V
VCC = Vp = 2.7 V
⎯
⎯
⎯
−1.0
mA
mA
LD/
fout
IOL
1.0
⎯
(Continued)
6
DS04–21368–2E
MB15F73UL
(Continued)
(VCC = 2.4 V to 3.6 V, Ta = −40 °C to +85 °C)
Value
Unit
Parameter
Symbol
Condition
VCC = Vp = 2.7 V,
VDOH = Vp / 2,
Ta = +25 °C
Min
Typ
Max
CS bit = “H”
CS bit = “L”
CS bit = “H”
CS bit = “L”
−8.2
−6.0
−4.1
mA
mA
mA
mA
*8
“H” level output
current
DoIF
DoRF
*4
IDOH
−2.2
4.1
−1.5
6.0
−0.8
8.2
VCC = Vp = 2.7 V,
VDOL = Vp / 2,
Ta = +25 °C
*8
“L” level output
current
DoIF
DoRF
IDOL
*5
0.8
1.5
2.2
IDOL/IDOH IDOMT
VDO = Vp / 2
⎯
⎯
3
⎯
⎯
%
%
*6
*7
Charge pump
current rate
vs VDO
vs Ta
IDOVD
0.5 V ≤ VDO ≤ Vp − 0.5 V
10
−40 °C ≤ Ta ≤ 85 °C,
VDO = Vp / 2
IDOTA
⎯
5
⎯
%
*1 : Conditions ; fosc = 12.8 MHz, Ta = +25 °C, SW = “L” in locking state.
*2 : VCCIF = VpIF = VCCRF = VpRF = 2.7 V, fosc = 12.8 MHz, Ta = +25 °C, in power saving mode.
PSIF = PSRF = GND
VIH = VCC, VIL = GND (at CLK, Data, LE)
*3 : AC coupling. 1000 pF capacitor is connected under the condition of Min. operating frequency.
*4 : The symbol “–” (minus) means the direction of current flow.
*5 : VCC = Vp = 2.7 V, Ta = +25 °C (||I3| − |I4||) / [ (|I3| + |I4|) / 2] × 100 (%)
*6 : VCC = Vp = 2.7 V, Ta = +25 °C [ (||I2| − |I1||) / 2] / [ (|I1| + |I2|) / 2] × 100 (%) (Applied to both lDOL and lDOH)
*7 : VCC = Vp = 2.7 V, [||IDO (+85 °C) | − |IDO (–40 °C) || / 2] / [|IDO (+85 °C) | + |IDO (–40 °C) | / 2] × 100 (%) (Applied to
both IDOL and IDOH)
*8 : When Charge pump current is measured, set LDS = “L” , T1 = “L” and T2 = “H”.
I
I
3
4
I
I
1
2
I
I
2
1
IDOL
IDOH
0.5
Vp/2
Vp − 0.5
Vp
Charge pump output voltage (V)
DS04–21368–2E
7
MB15F73UL
■ FUNCTIONAL DESCRIPTION
1. Pulse swallow function
fVCO = [ (P × N) + A] × fOSC ÷ R
fVCO : Output frequency of external voltage controlled oscillator (VCO)
P
N
A
: Preset divide ratio of dual modulus prescaler (8 or 16 for IF-PLL, 64or 128 for RF-PLL)
: Preset divide ratio of binary 11-bit programmable counter (3 to 2,047)
: Preset divide ratio of binary 7-bit swallow counter (0 ≤ A ≤ 127, A < N)
fOSC : Reference oscillation frequency (OSCIN input frequency)
: Preset divide ratio of binary 14-bit programmable reference counter (3 to 16,383)
R
2. Serial Data Input
The serial data is entered using three pins, Data pin, Clock pin, and LE pin. Programmable dividers of IF/
RF-PLL sections, programmable reference dividers of IF/RF-PLL sections are controlled individually.
The serial data of binary data is entered through Data pin.
On rising edge of Clock, one bit of the serial data is transferred into the shift register. On a rising edge of
load enable signal, the data stored in the shift register is transferred to one of latches depending upon the
control bit data setting.
The programmable The programmable
The programmable
The programmable
reference counter reference counter counterandtheswallow counter and the swallow
for the IF-PLL
for the RF-PLL
counter for the IF-PLL
counter for the RF-PLL
CN1
CN2
0
0
1
0
0
1
1
1
(1) Shift Register Configuration
• Programmable Reference Counter
(LSB)
Data Flow
(MSB)
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CN1 CN2 T1 T2 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 CS X
X
X
X
CS
: Charge pump current select bit
R1 to R14 : Divide ratio setting bits for the programmable reference counter (3 to 16,383)
T1, 2
CN1, 2
X
: LD/fout output setting bit
: Control bit
: Dummy bits (Set “0” or “1”)
Note : Data input with MSB first.
8
DS04–21368–2E
MB15F73UL
• Programmable Counter
(LSB)
Data Flow
(MSB)
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
N1 N2 N3 N4 N5 N6 N7 N8 N9 N10 N11
A1 A2 A3 A4 A5 A6 A7
SWIF/RF FCIF/RF
CN1 CN2 LDS
A1 to A7
: Divide ratio setting bits for the swallow counter (0 to 127)
: Divide ratio setting bits for the programmable counter (3 to 2,047)
: LD/fout signal select bit
N1 to N11
LDS
SWIF/RF
FCIF/RF
CN1, 2
: Divide ratio setting bit for the prescaler (IF : SWIF, RF : SWRF)
: Phase control bit for the phase detector (IF : FCIF, RF : FCRF)
: Control bit
Note : Data input with MSB first.
(2) Data setting
• Binary 14-bit Programmable Reference Counter Data Setting
Divide ratio R14 R13 R12 R11 R10 R9 R8 R7 R6 R5 R4 R3 R2 R1
3
0
0
0
0
0
0
0
0
0
0
0
0
1
1
4
•
•
•
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
1
•
•
•
1
0
•
•
•
1
0
•
•
•
1
16383
Note : Divide ratio less than 3 is prohibited.
• Binary 11-bit Programmable Counter Data Setting
Divide ratio N11 N10 N9 N8 N7 N6 N5 N4 N3 N2 N1
3
0
0
0
0
0
0
0
0
0
1
1
4
•
•
•
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
1
•
•
•
1
0
•
•
•
1
0
•
•
•
1
2047
Note : Divide ratio less than 3 is prohibited
• Binary 7-bit Swallow Counter Data Setting
Divide ratio A7 A6 A5 A4 A3 A2 A1
0
0
0
0
0
0
0
0
1
•
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
0
•
•
•
1
1
•
•
•
1
•
•
127
DS04–21368–2E
9
MB15F73UL
• Prescaler Data Setting
Divide ratio
SW = “H”
8/9
SW = “L”
16/17
Prescaler divide ratio IF-PLL
Prescaler divide ratio RF-PLL
64/65
128/129
• Charge Pump Current Setting
Current value
6.0 mA
CS
1
1.5 mA
0
• LD/fout output Selectable Bit Setting
LD/fout pin state
LD output
frIF
LDS
T1
T2
0
0
0
1
1
0
1
0
1
0
0
0
1
1
0
frRF
fpIF
1
0
fout
output
1
1
fpRF
1
1
• Phase Comparator Phase Switching Data Setting
FCIF, RF = “H”
Phase comparator input
DoIF, RF
FCIF, RF = “L”
DoIF, RF
fr > fp
fr < fp
H
L
L
H
Z
fr = fp
Z
Z : High-impedance
Depending upon the VCO and LPF polarity, FC bit should be set.
High
(1)
(1) VCO polarity FC = “H”
(2) VCO polarity FC = “L”
VCO Output
Frequency
(2)
Max.
LPF Output voltage
Note : Give attention to the polarity for using active type LPF.
10
DS04–21368–2E
MB15F73UL
3. Power Saving Mode (Intermittent Mode Control Circuit)
Status
PS pin
H
L
Normal mode
Power saving mode
The intermittent mode control circuit reduces the PLL power consumption.
By setting the PS pin low, the device enters into the power saving mode, reducing the current consumption.
See the Electrical Characteristics chart for the specific value.
The phase detector output, Do, becomes high impedance.
For the dual PLL, the lock detector, LD, is as shown in the LD Output Logic table.
Setting the PS pin high, releases the power saving mode, and the device works normally.
The intermittent mode control circuit also ensures a smooth startup when the device returns to normal
operation. When the PLL is returned to normal operation, the phase comparator output signal is unpredict-
able. This is because of the unknown relationship between the comparison frequency (fp) and the reference
frequency (fr) which can cause a major change in the comparaor output, resulting in a VCO frequency jump
and an increase in lockup time.
To prevent a major VCO frequency jump, the intermittent mode control circuit limits the magnitude of the
error signal from the phase detector when it returns to normal operation.
Notes : • When power (VCC) is first applied, the device must be in standby mode, PS = Low, for at least 1 μs.
• PS pin must be set “L” at Power-ON.
OFF
ON
VCC
tV ≥ 1 μs
Clock
Data
LE
PS
tPS ≥ 100 ns
(1)
(2)
(3)
(1) PS = L (power saving mode) at Power-ON
(2) Set serial data at least 1 μs after the power supply becomes stable (VCC ≥ 2.2 V) .
(3) Release power saving mode (PSIF, PSRF : “L” → “H”) at least 100 ns later after setting serial data.
DS04–21368–2E
11
MB15F73UL
4. Serial Data Data Input Timing
Divide ratio is performed through a serial interface using the Data pin, Clock pin, and LE pin.
Setting data is read into the shift register at the rise of the Clock signal, and transferred to a latch at the rise
of the LE signal. The following diagram shows the data input timing.
1st data
2nd data
Invalid data
Control bit
Data
MSB
LSB
Clock
LE
t1
t2
t3
t6
t7
t4
t5
Parameter Min.
Typ.
Max.
⎯
Unit
Parameter
Min. Typ. Max.
Unit
ns
t1
t2
t3
t4
20
20
30
30
⎯
⎯
⎯
⎯
ns
ns
ns
ns
t5
t6
t7
100
20
⎯
⎯
⎯
⎯
⎯
⎯
⎯
ns
⎯
100
ns
⎯
Note : LE should be “L” when the data is transferred into the shift register.
12
DS04–21368–2E
MB15F73UL
■ PHASE COMPARATOR OUTPUT WAVEFORM
frIF/RF
fpIF/RF
tWU
tWL
LD
(FC bit = High)
H
DoIF/RF
Z
L
(FC bit = Low)
H
DoIF/RF
Z
L
• LD Output Logic
IF-PLL section
RF-PLL section
Locking state/Power saving state
Unlocking state
LD output
Locking state/Power saving state
Locking state/Power saving state
Unlocking state
H
L
L
L
Locking state/Power saving state
Unlocking state
Unlocking state
Notes : • Phase error detection range = −2π to +2π
• Pulses on DoIF/RF signals during locking state are output to prevent dead zone.
• LD output becomes low when phase error is tWU or more.
• LD output becomes high when phase error is tWL or less and continues to be so for three cycles or more.
• tWU and tWL depend on OSCIN input frequency as follows.
tWU ≥ 2/fosc : e.g. tWU ≥ 156.3 ns when fosc = 12.8 MHz
tWU ≤ 4/fosc : e.g. tWL ≤ 312.5 ns when fosc = 12.8 MHz
DS04–21368–2E
13
MB15F73UL
■ TEST CIRCUIT (for Measuring Input Sensitivity fin/OSCIN)
fout
Oscilloscope
1000 pF
VpIF
VCCIF
1000 pF
S.G.
50 Ω
0.1 μF
0.1 μF
1000 pF
S.G.
50 Ω
LD/fout
10
DoIF
9
VpIF
PSIF
VCCIF
GNDIF
XfinIF
4
finIF
3
GND
2
OSCIN
1
8
7
6
5
11
12
13
14
15
16
17
18
LE
19
20
DoRF
VpRF
PSRF
VCCRF GNDRF XfinRF
finRF
Data
Clock
1000 pF
Controller
(divide ratio setting)
1000 pF
VpRF
VCCRF
S.G.
50 Ω
0.1 μF
0.1 μF
Note : The terminal number shows that of TSSOP-20.
14
DS04–21368–2E
MB15F73UL
■ TYPICAL CHARACTERISTICS
1. fin input sensitivity
RF-PLL input sensitivity vs. Input frequency
10
0
SPEC
−10
−20
−30
−40
−50
VCC = 2.4 V
VCC = 2.7 V
VCC = 3.0 V
VCC = 3.6 V
SPEC
0
400
800
1200
1600
2000
2400
2800
3200
3600
4000
finRF (MHz)
IF-PLL input sensitivity vs. Input frequency
10
0
SPEC
−10
−20
−30
−40
−50
VCC = 2.4 V
VCC = 2.7 V
VCC = 3.0 V
VCC = 3.6 V
SPEC
0
100
200
300
400
500
600
700
800
900
1000
1100
1200
finIF (MHz)
DS04–21368–2E
15
MB15F73UL
2. OSCIN input sensitivity
Input sensitivity vs. Input frequency
10
SPEC
0
−10
−20
−30
−40
−50
VCC = 2.4 V
VCC = 2.7 V
VCC = 3.0 V
VCC = 3.6 V
SPEC
−60
0
50
100
150
200
250
300
Input frequency fOSC (MHz)
16
DS04–21368–2E
MB15F73UL
3. RF-PLL Do output current
• 1.5 mA mode
IDO − VDO
10.0
VCC = Vp = 2.7 V
0
−10.0
0.0
2.0
3.0
1.0
Charge pump output voltage VDO (V)
• 6.0 mA mode
IDO − VDO
10.0
VCC = Vp = 2.7 V
0
−10.0
0.0
1.0
2.0
3.0
Charge pump output voltage VDO (V)
DS04–21368–2E
17
MB15F73UL
4. IF-PLL Do output current
• 1.5 mA mode
IDO − VDO
10.0
V
CC = Vp = 2.7 V
0
−10.0
0.0
1.0
2.0
3.0
Charge pump output voltage VDO (V)
• 6.0 mA mode
IDO − VDO
10.0
VCC = Vp = 2.7 V
0
−10.0
0.0
1.0
2.0
3.0
Charge pump output voltage VDO (V)
18
DS04–21368–2E
MB15F73UL
5. fin input impedance
finIF input impedance
4 : 17.586 Ω
−152.84 Ω
1.7356 pF
600.000 000 MHz
1 : 942.56 Ω
−1.0998 kΩ
50 MHz
2 : 102.27 Ω
−453.08 Ω
200 MHz
3 : 30.813 Ω
−231.69 Ω
400 MHz
1
2
4
3
START 50.000 000 MHz
STOP 600.000 000 MHz
finRF input impedance
4 : 9.8589 Ω
−12.918 Ω
5.4757 pF
2 250.000 000 MHz
1 : 110.8
Ω
−450.61 Ω
200 MHz
2 : 10.215 Ω
−85.023 Ω
1 GHz
3 : 8.248
Ω
−46.791 Ω
1.5 GHz
4
1
2
3
START 200.000 000 MHz
STOP 2 250.000 000 MHz
DS04–21368–2E
19
MB15F73UL
6. OSCIN input impedance
OSCIN input impedance
4 : 25.625 Ω
−708.63 Ω
2.246 pF
100.000 000 MHz
1 :12.925 kΩ
−13.855 kΩ
3 MHz
2 : 453.87 Ω
−3.5288 kΩ
20 MHz
3 : 112.38 Ω
−1.7836 kΩ
40 MHz
4
1
2
3
START 3.000 000 MHz
STOP 100.000 000 MHz
20
DS04–21368–2E
MB15F73UL
■ REFERENCE INFORMATION
(for Lock-up Time, Phase Noise and Reference Leakage)
f
VCO = 1607 MHz VCC = 3.0 V
K
V
= 30 MHz/V
V
VCO = 2.3 V
Ta = + 25 °C
OSC = 14.4 MHz CP : 6 mA mode
LPF
Test Circuit
OSCIN
fr = 25 kHz
f
S.G.
Do
LPF
VCO : FUJITSU MEDIA DEVICES
(VC-2R3A50-1619)
fin
20 k Ω
3.6 k Ω
To VCO
Spectrum
Analyzer
VCO
4700 pF
68 pF
0.039 μF
• PLL Reference Leakage
ATTEN 10 dB
RL −5.0 dBm
VAVG 0
10 dB/
ΔMKR −71.34 dB
25.0 kHz
∗
ΔMKR
25.0 kHz
−71.34 dB
CENTER 1.6070000 GHz
SPAN 200.0 kHz
SWP 500 ms
∗
RBW 1.0 kHz
VBW 1.0 kHz
• PLL Phase Noise
ATTEN 10 dB
RL −5.0 dBm
VAVG 38
10 dB/
ΔMKR −47.16 dB
4.67 kHz
ΔMKR
4.67 kHz
−47.16 dB
D
S
CENTER 1.60700000 GHz
SPAN 20.00 kHz
SWP 1.60 s
∗
RBW 100 Hz
VBW 100 Hz
(Continued)
DS04–21368–2E
21
MB15F73UL
(Continued)
PLL Lock Up time
PLL Lock Up time
1607 MHz→1631 MHz within 1 kHz
1631 MHz→1607 MHz within 1 kHz
L ch→H ch
1.09 ms
H ch→L ch
1.28 ms
1.631004000 GHz
1.631000000 GHz
1.607004000 GHz
1.607000000 GHz
1.630996000 GHz
0.00 s
1.606996000 GHz
0.00 s
2.500 ms
5.000 ms
2.500 ms
5.000 ms
500.0 μs/div
500.0 μs/div
22
DS04–21368–2E
MB15F73UL
■ APPLICATION EXAMPLE
OUTPUT
VCO
2.7 V
LPF
2.7 V
from controller
1000 pF
1000 pF
0.1 μF 0.1 μF
Clock DATA
LE
18
finRF
17
XfinRF GNDRF
VCCRF
PSRF
VpRF
DoRF
20
19
16
15
14
13
12
11
MB 15F73UL
1
2
3
4
5
6
7
8
9
10
OSCIN
GND
finIF
XfinIF
GNDIF
VCCIF
PSIF
VpIF
DoIF
LD/fout
Lock Det.
2.7 V
2.7 V
1000 pF
1000 pF
1000 pF
0.1 μF
0.1 μF
TCXO
OUTPUT
VCO
LPF
Notes : •Clock, Data, LE : The schmitt trigger circuit is provided (insert a pull-down or pull-up register
to prevent oscillation when open-circuit in the input) .
•The terminal number shows that of TSSOP-20.
DS04–21368–2E
23
MB15F73UL
■ USAGE PRECAUTIONS
(1) VCCRF, VpRF, VCCIF and VpIF must be equal voltage.
Even if either RF-PLL or IF-PLL is not used, power must be supplied to VCCRF, VpRF, VCCIF and VpIF to keep
them equal. It is recommended that the non-use PLL is controlled by power saving function.
(2) To protect against damage by electrostatic discharge, note the following handling precautions :
-Store and transport devices in conductive containers.
-Use properly grounded workstations, tools, and equipment.
-Turn off power before inserting or removing this device into or from a socket.
-Protect leads with conductive sheet, when transporting a board mounted device
24
DS04–21368–2E
MB15F73UL
■ ORDERING INFORMATION
Part number
Package
Remarks
20-pin plastic TSSOP
(FPT-20P-M06)
MB15F73ULPFT
MB15F73ULWQN
20-pin, Plastic QFN
(LCC-20P-M63)
DS04–21368–2E
25
MB15F73UL
■ PACKAGE DIMENSIONS
20-pin plastic TSSOP
Lead pitch
0.65 mm
4.40 × 6.50 mm
Gullwing
Package width
package length
×
Lead shape
Sealing method
Mounting height
Weight
Plastic mold
1.10 mm MAX
0.08g
Code
(Reference)
P-TSSOP20-4.4×6.5-0.65
(FPT-20P-M06)
20-pin plastic TSSOP
Note 1) *1 : Resin protrusion. (Each side : +0.15 (.006) Max).
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
(FPT-20P-M06)
1 6.50±0.10(.256±.004)
*
0.17±0.05
(.007±.002)
20
11
24.40±0.10 6.40±0.20
(.173±.004) (.252±.008)
*
INDEX
Details of "A" part
1.05±0.05
(Mounting height)
(.041±.002)
1
10
LEAD No.
"A"
0.65(.026)
0.24±0.08
(.009±.003)
0~8°
M
0.13(.005)
0.07 +–00..0073 .003 –+..000031
(0.50(.020))
(Stand off)
0.25(.010)
0.60±0.15
(.024±.006)
0.10(.004)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2003-2010 FUJITSU SEMICONDUCTOR LIMITED F20026S-c-3-5
(Continued)
26
DS04–21368–2E
MB15F73UL
(Continued)
20-pin plastic QFN
Lead pitch
0.50 mm
4.00 mm × 4.00 mm
Plastic mold
Package width ×
package length
Sealing method
Mounting height
Weight
0.80 mm MAX
0.04 g
(LCC-20P-M63)
20-pin plastic QFN
(LCC-20P-M63)
2.00±0.10
4.00±0.10
(.0.79±.004)
(.157±.004)
0.25 +–00..0075
2.00±0.10
(.0.79±.004)
4.00±0.10
(.157±.004)
+.002
(.010
)
–.003
INDEX AREA
1PIN ID
(C0.35(C.014))
0.40±0.05
(.016±.002)
0.50(.020)
(TYP)
0.75±0.05
(.030±.002)
0.02 +–00..0023
(.001
0.20(.008)
+.001
–.001
)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2012 FUJITSU SEMICONDUCTOR LIMITED HMbC20-63Sc-1-1
DS04–21368–2E
27
MB15F73UL
FUJITSU SEMICONDUCTOR LIMITED
Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome,
Kohoku-ku Yokohama Kanagawa 222-0033, Japan
Tel: +81-45-415-5858
http://jp.fujitsu.com/fsl/en/
For further information please contact:
North and South America
Asia Pacific
FUJITSU SEMICONDUCTOR AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://us.fujitsu.com/micro/
FUJITSU SEMICONDUCTOR ASIA PTE. LTD.
151 Lorong Chuan,
#05-08 New Tech Park 556741 Singapore
Tel : +65-6281-0770 Fax : +65-6281-0220
http://sg.fujitsu.com/semiconductor/
Europe
FUJITSU SEMICONDUCTOR SHANGHAI CO., LTD.
30F, Kerry Parkside, 1155 Fang Dian Road, Pudong District,
Shanghai 201204, China
Tel : +86-21-6146-3688 Fax : +86-21-6146-3660
http://cn.fujitsu.com/fss/
FUJITSU SEMICONDUCTOR EUROPE GmbH
Pittlerstrasse 47, 63225 Langen, Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/semiconductor/
Korea
FUJITSU SEMICONDUCTOR PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel : +852-2377-0226 Fax : +852-2376-3269
http://cn.fujitsu.com/fsp/
FUJITSU SEMICONDUCTOR KOREA LTD.
902 Kosmo Tower Building, 1002 Daechi-Dong,
Gangnam-Gu, Seoul 135-280, Republic of Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://kr.fujitsu.com/fsk/
Specifications are subject to change without notice. For further information please contact each office.
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does
not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating
the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any
third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right
by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or
other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect
to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in
weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages aris-
ing in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures
by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-
current levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations
of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited: Sales Promotion Department
相关型号：
©2020 ICPDF网 联系我们和版权申明