MB3773PF-XXXE1 [SPANSION]
Power Supply Management Circuit, Fixed, 1 Channel, BIPolar, PDSO8, 5.30 X 6.35 MM, 2.25 MM HEIGHT, 1.27 MM PITCH, ROHS COMPLIANT, PLASTIC, SOP-8;![MB3773PF-XXXE1](http://pdffile.icpdf.com/pdf2/p00237/img/icpdf/MB3773PF-G-B_1391420_icpdf.jpg)
型号: | MB3773PF-XXXE1 |
厂家: | ![]() |
描述: | Power Supply Management Circuit, Fixed, 1 Channel, BIPolar, PDSO8, 5.30 X 6.35 MM, 2.25 MM HEIGHT, 1.27 MM PITCH, ROHS COMPLIANT, PLASTIC, SOP-8 光电二极管 |
文件: | 总32页 (文件大小:392K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
FUJITSU MICROELECTRONICS
DATA SHEET
DS04-27401-8Ea
ASSP
BIPOLAR
Power Supply Monitor
with Watch-Dog Timer
MB3773
■ DESCRIPTION
MB3773 generates the reset signal to protect an arbitrary system when the power-supply voltage momentarily is
intercepted or decreased. It is IC for the power-supply voltage watch and “Power on reset” is generated at the
normal return of the power supply. MB3773 sends the microprocessor the reset signal when decreasing more
than the voltage, which the power supply of the system specified, and the computer data is protected from an
accidental deletion.
In addition, the watch-dog timer for the operation diagnosis of the system is built into, and various microprocessor
systems can provide the fail-safe function. If MB3773 does not receive the clock pulse from the processor for a
specified period, MB3773 generates the reset signal.
■ FEATURES
• Precision voltage detection (VS = 4.2 V ± 2.5 %)
• Detection threshold voltage has hysteresis function
• Low voltage output for reset signal (VCC = 0.8 V Typ)
• Precision reference voltage output (VR = 1.245 V ± 1.5%)
• With built-in watch-dog timer of edge trigger input.
• External parts are few.(1 piece in capacity)
• The reset signal outputs the positive and negative both theories reason.
• One type of package (SOP-8pin : 1 type)
■ APPLICATION
• Industrial Equipment
• Arcade Amusement
etc.
Copyright©2003-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2006.5
MB3773
■ PIN ASSIGNMENT
(TOP VIEW)
C T
RESET
CK
1
2
8
7
RESET
V S
3
4
6
5
V REF
GND
V CC
(FPT-8P-M01)
2
MB3773
■ BLOCK DIAGRAM
VCC
5
Reference AMP
=: 1.24 V
=: 1.24 V
Reference Voltage Generator
+
_
VREF
6
=: 100
=: 1.2 µA
COMP.O
kΩ
=: 10 µA
+
_
+
_
=: 10 µA
COMP.S
+
_
R
S
Q
VS
7
=: 40 kΩ
Inhibit
Watch-
Dog
CK
3
Timer
P.G
4
GND
2
1
8
CT
RESET
RESET
3
MB3773
■ FUNCTIONAL DESCRIPTIONS
Comp.S is comparator including hysteresis. it compare the reference voltage and the voltage of Vs, so that when
the voltage of Vs terminal falls below approximately 1.23 V, reset signal outputs.
Instantaneous breaks or drops in the power can be detected as abnormal conditions by the MB3773 within a
2 µs interval.
However because momentary breaks or drops of this duration do not cause problems in actual systems in some
cases, a delayed trigger function can be created by connecting capacitors to the Vs terminal.
Comp.O is comparator for turning on/off the output and, compare the voltage of the CT terminal and the threshold
voltage. Because the RESET/RESET outputs have built-in pull-up circuit, there is no need to connect to external
pull-up resistor when connected to a high impedance load such as CMOS logic IC.
(It corresponds to 500 kΩ at Vcc = 5 V.) when the voltage of the CK terminal changes from the “high” level into
the “Low” level, pulse generator is sent to the watch-dog timer by generating the pulse momentarily at the time
of drop from the threshold level.
When power-supply voltages fall more than detecting voltages, the watch-dog timer becomes an interdiction.
The Reference amplifier is an op-amp to output the reference voltage.
If the comparator is put up outside, two or more power-supply voltage monitor and overvoltage monitor can be
done.
If it uses a comparator of the open-collector output, and the output of the comparator is connected with the Vs
terminal of MB3773 without the pull-up resistor, it is possible to voltage monitor with reset-hold time.
4
MB3773
• MB3773 Basic Operation
VCC
VCC
Logic Circuit
TPR (ms) =: 1000 · CT (µF)
TWD (ms) =: 100 · CT (µF)
RESET
RESET
CK
CT
RESET
RESET
CK
TWR (ms) =:
20 · CT (µF)
Example : CT = 0.1 µF
TRR (ms) =: 100 (ms)
GND
TWD (ms) =: 10 (ms)
TWR (ms) =: 2 (ms)
VCC
VSH
VSL
0.8 V
CK
TCK
CT
TPR
RESET
TWD
TWR
TPR
(1) (2)
(3)(4)(5)
(5)
(6)(7)
(8)(9)
(10)
(11) (12)
5
MB3773
■ OPERATION SEQUENCE
(1) When Vcc rises to about 0.8 V, RESET goes “Low” and RESET goes “High”.
The pull-up current of approximately 1 µA (Vcc = 0.8 V) is output from RESET.
(2) When Vcc rises to VSH (=: 4.3V) , the charge with CT starts.
At this time, the output is being reset.
(3) When CT begins charging, RESET goes “High” and RESET goes “Low”.
After TPR reset of the output is released.
Reset hold time: TPR (ms) =: 1000 × CT (µF)
After releasing reset, the discharge of CT starts, and watch-dog timer operation starts.
TPR is not influenced by the CK input.
(4) C changes from the discharge into the charge if the clock (Negative edge) is input to the CK terminal
while discharging CT.
(5) C changes from the charge into the discharge when the voltage of CT reaches a constant
threshold (=: 1.4 V) .
(4) and (5) are repeated while a normal clock is input by the logic system.
(6) When the clock is cut off, gets, and the voltage of CT falls on threshold (=: 0.4 V) of reset on, RESET goes
“Low” and RESET goes “High”.
Discharge time of CT until reset is output: TWD is watch-dog timer monitoring time.
TWD (ms) =: 100 × CT (µF)
Because the charging time of CT is added at accurate time from stop of the clock and getting to the output
of reset of the clock, TWD becomes maximum TWD + TWR by minimum TWD.
(7) Reset time in operating watch-dog timer:TWR is charging time where the voltage of CT goes up to off
threshold (=: 1.4 V) for reset.
TWR (ms) =: 20 × CT (µF)
Reset of the output is released after CT reaches an off threshold for reset, and CT starts the discharge,
after that if the clock is normally input, operation repeats (4) and (5) , when the clock is cut off, operation
repeats (6) and (7) .
(8) When Vcc falls on VSL (=: 4.2 V) , reset is output. CT is rapidly discharged of at the same time.
(9) When Vcc goes up to VSH, the charge with CT is started.
When Vcc is momentarily low,
After falling VSL or less Vcc, the time to going up is the standard value of the Vcc input pulse width in VSH or
more.
After the charge of CT is discharged, the charge is started if it is TPI or more.
(10) Reset of the output is released after TPR, after Vcc becomes VSH or more, and the watch-dog timer starts.
After that, when Vcc becomes VSL or less, (8) to (10) is repeated.
(11) While power supply is off, when Vcc becomes VSL or less, reset is output.
(12) The reset output is maintained until Vcc becomes 0.8 V when Vcc falls on 0 V.
6
MB3773
■ ABSOLUTE MAXIMUM RATINGS
Rating
Parameter
Supply voltage
Symbol
Unit
Min
− 0.3
− 0.3
− 0.3
− 0.3
Max
VCC
VS
+ 18
V
VCC + 0.3 ( ≤ +18)
V
V
Input voltage
VCK
VOH
PD
+ 18
VCC + 0.3 ( ≤ +18)
200
RESET, RESET Supply voltage
Power dissipation (Ta ≤ +85 °C)
Storage temperature
V
mW
°C
TSTG
− 55
+ 125
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
■ RECOMMENDED OPERATING CONDITIONS
Value
Parameter
Symbol
Unit
Min
+ 3.5
0
Max
+ 16
20
Supply voltage
VCC
IOL
V
RESET, RESET sink current
VREF output current
mA
µA
ms
µs
IOUT
tWD
− 200
0.1
+ 5
Watch clock setting time
CK Rising/falling time
1000
100
10
tFC, tRC
CT
Terminal capacitance
0.001
− 40
µF
°C
Operating ambient temperature
Ta
+ 85
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
representatives beforehand.
7
MB3773
■ ELECTORICAL CHARACTERISTICS
(1) DC Characteristics
(VCC = 5 V, Ta = + 25 °C)
Value
Unit
Parameter
Supply current
Symbol
ICC
Condition
Min
Typ
600
Max
900
Watch-dog timer operating
µA
VCC
4.10
4.05
4.20
4.15
50
4.20
4.20
4.30
4.30
100
4.30
4.35
4.40
4.45
150
VSL
Ta = − 40 °C to + 85 °C
Detection voltage
V
VCC
VSH
VHYS
VREF
Ta = − 40 °C to + 85 °C
Hysteresis width
VCC
mV
V
1.227 1.245 1.263
1.215 1.245 1.275
Reference voltage
Ta = − 40 °C to + 85 °C
VCC = 3.5 V to 16 V
Reference voltage change rate
∆VREF1
∆VREF2
3
10
mV
mV
V
Reference voltage output
loading change rate
IOUT = − 200 µA to + 5 µA
− 5
+ 5
CK threshold voltage
VTH
IIH
Ta = − 40 °C to + 85 °C
VCK = 5.0 V
0.8
1.25
0
2.0
1.0
CK input current
µA
µA
V
IIL
VCK = 0.0 V
− 1.0 − 0.1
Watch-dog timer operating
VCT = 1.0 V
CT discharge current
ICTD
7
10
14
VOH1
VOH2
VOL1
VOL2
VOL3
VOL4
IOL1
VS open, IRESET = − 5 µA
VS = 0 V, IRESET = − 5 µA
VS = 0 V, IRESET = 3 mA
VS = 0 V, IRESET = 10 mA
VS open, IRESET = 3 mA
VS open, IRESET = 10 mA
VS = 0 V, VRESET = 1.0 V
VS open, VRESET = 1.0 V
4.5
4.5
4.9
4.9
0.2
0.3
0.2
0.3
60
High level output voltage
0.4
0.5
0.4
0.5
Output saturation voltage
Output sink current
V
20
20
mA
IOL2
60
Power on reset operating
VCT = 1.0 V
CT charge current
ICTU
0.5
1.2
0.8
2.5
1.2
µA
VRESET = 0.4 V,
IRESET = 0.2 mA
Min supply voltage for RESET
VCCL1
V
VRESET = VCC − 0.1 V,
RL (between pin 2 and GND) =
1 MΩ
Min supply voltage for RESET
VCCL2
0.8
1.2
V
8
MB3773
(2)AC Characteristics
Parameter
(VCC = 5 V, Ta = + 25 °C)
Value
Unit
Symbol
TPI
Condition
Min
Typ Max
5 V
4 V
VCC input pulse width
CK input pulse width
8.0
3.0
µs
µs
VCC
CK
TCKW
or
CK input frequency
TCK
TWD
TWR
20
5
10
2
15
3
µs
ms
ms
Watch-dog timer watching time
Watch-dog timer reset time
CT = 0.1 µF
CT = 0.1 µF
1
Rising reset hold time
TPR
TPD1
TPD2
tR
50
100
2
150 ms
CT = 0.1 µF, VCC
RESET, RL = 2.2 kΩ,
CL = 100 pF
10
µs
10
Output propagation
delay time from VCC
RESET, RL = 2.2 kΩ,
CL = 100 pF
3
RL = 2.2 kΩ,
CL = 100 pF
Output rising time*
Output falling time*
1.0
0.1
1.5
µs
RL = 2.2 kΩ,
CL = 100 pF
tF
0.5
* : Output rising/falling time are measured at 10 % to 90 % of voltage.
9
MB3773
■ TYPICAL CHARACTERISTIC CURVES
Supply current vs. Supply voltage
Output voltage vs. Supply voltage
(RESET terminal)
6.0
0.75
Ta = + 85 °C
Ta = + 25 °C
Pull up 2.2 kΩ
0.65
5.0
Ta = − 40 °C,
+
25 °C,
+
85 °C
Ta = − 40 °C
0.55
0.45
0.35
4.0
3.0
2.0
1.0
CT = 0.1 µF
Ta = − 40 °C
Ta = + 25 °C
Ta = + 85 °C
0.25
0.15
0
1.0
2.0
3.0
4.0
5.0
6.0 7.0
0
2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
Supply voltage VCC (V)
Supply voltage VCC (V)
Detection voltage (VSH, VSL) vs.
Output voltage vs. Supply voltage
Operating ambient temperature
(RESET terminal)
(RESET, RESET terminal)
4.50
6.0
5.0
Pull up 2.2 kΩ
VSH
4.44
4.30
4.20
4.10
4.0
VSL
3.0
2.0
1.0
Ta = + 85 °C
Ta = + 25 °C
Ta = − 40 °C
4.00
0
1.0 2.0
3.0 4.0
5.0
6.0
7.0
−40 −20
0
+20 +40 +60 +80 +100
Supply voltage VCC (V)
Operating ambient temperature Ta ( °C)
Output saturation voltage
vs. Output sink current
(RESET terminal)
Output saturation voltage
vs. Output sink current
(RESET terminal)
500
CT = 0.1µF
Ta = − 40 °C
CT = 0.1µF
400
Ta = −40 °C
400
300
200
300
200
100
Ta = + 25 °C
Ta = + 85 °C
Ta = +25 °C
Ta = +85 °C
100
0
2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0
Output sink current IOL2 (mA)
0
2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0
Output sink current IOL8 (mA)
(Continued)
10
MB3773
High level output voltage
vs. High level output current
High level output voltage
vs. High level output current
(RESET terminal)
(RESET terminal)
5.0
4.5
5.0
4.5
CT = 0.1 µF
CT = 0.1 µF
Ta = +25 °C
Ta = +85 °C
Ta = +25 °C
Ta = +85 °C
Ta = −40 °C
Ta = −40 °C
4.0
4.0
0
−5
−10
−15
0
−5
−10
−15
High level output current IOH8 (µA)
High level output current IOH2 (µA)
Reference voltage
vs. Supply voltage
Reference voltage
vs. Reference current
1.255
1.250
1.246
1.244
1.242
1.240
1.238
1.236
1.234
CT = 0.1 µF
Ta = +25 °C
Ta = +85 °C
Ta = −40 °C
CT = 0.1 µF
Ta = +25 °C
Ta = +85 °C
1.245
1.240
Ta = −40 °C
0
−40
−80
−120
−160
−200 −240
0
3.0 5.0 7.0 9.0 11.0 13.0 15.0 17.0 19.0 21.0
Supply voltage VCC (V)
Reference current IREF (µA)
Reference voltage vs.
Rising reset hold time vs.
Operating ambient temperature
Operating ambient temperature
1.27
160
VCC = 5 V
1.26
1.25
140
CT = 0.1 µF
120
100
80
1.24
1.23
1.22
1.21
60
40
0
−40 −20
0
+20 +40 +60 +80 +100
−40 −20
0
+20 +40 +60 +80 +100
Operating ambient temperature Ta ( °C)
Operating ambient temperature Ta ( °C)
(Continued)
11
MB3773
(Continued)
Reset time vs.
Operating ambient temperature
Watch-dog timer watching time vs.
Operating ambient temperature
(At watch-dog timer)
16
V
CC = 5 V
V
CC = 5 V
3
2
CT = 0.1 µF
CT = 0.1 µF
14
12
10
8
1
0
6
4
0
−40 −20
0
+20 +40 +60 +80 +100
−40 −20
0
+20 +40 +60 +80 +100
Operating ambient temperature Ta ( °C)
Operating ambient temperature Ta ( °C)
Watch-dog timer watching time
vs.
Reset time vs.
CT terminal capacitance
Rising reset hold time vs.
CT terminal capacitance
CT terminal capacitance
(at watch-dog timer)
10 6
10 5
10 4
10 6
10 5
10 4
10 2
10 1
10 0
10 3
10 3
Ta = +25 °C,
+85 °C
Ta = −40 °C
10 2
10 2
10 1
Ta =
Ta = −40 °C
+25 °C, +85 °C
10 1
Ta =
Ta = +25 °C, +85 °C
10 −1
10 −2
10 −3
−40 °C
10 0
10 −1
10 −2
10 0
10 −1
10 −2
10 −3
10 −3
10 − 10 − 10 − 10 0 10 1 10 2
3
2
1
10 −3 10 −2 10 −1 10 0 10 1 10 2
10 −3 10 −2 10 −1 10 0 10 1 10 2
CT terminal capacitance CT (µF)
CT terminal capacitance CT (µF)
CT terminal capacitance CT (µF)
12
MB3773
■ APPLICATION CIRCUIT
EXAMPLE 1: Monitoring 5V Supply Voltage and Watch-dog Timer
VCC (5V)
MB3773
Logic circuit
8
7
6
5
1
2
3
4
RESET
RESET
CK
CT
GND
Notes : • Supply voltage is monitored using VS.
• Detection voltage are VSH and VSL.
EXAMPLE 2: 5V Supply Voltage Monitoring (external fine-tuning type)
VCC (5V)
MB3773
R1
R2
Logic circuit
RESET
1
2
3
4
8
7
6
5
RESET
CK
CT
GND
Notes : • Vs detection voltage can be adjusted externally.
• Based on selecting R1 and R2 values that are sufficiently lower than the resistance of the IC’s
internal voltage divider, the detection voltage can be set according to the resistance ratio of
R1 and R2 (Refer to the table below.)
R1 (kΩ)
10
R2 (kΩ)
3.9
Detection voltage: VSL (V)
Detection voltage: VSH (V)
4.4
4.1
4.5
4.2
9.1
3.9
13
MB3773
EXAMPLE 3: With Forced Reset (with reset hold)
(a)
VCC
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
CT
SW
GND
Note : Grounding pin 7 at the time of SW ON sets RESET (pin 8) to Low and RESET (pin 2) to High.
(b)
VCC
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
Tr
10 kΩ
10 kΩ
Cr
GND
RESIN
Note : Feeding the signal to terminal RESIN and turning on Tr sets the RESET terminal to Low and
the RESET terminal to High.
14
MB3773
EXAMPLE 4: Monitoring Two Supply Voltages (with hysteresis, reset output and NMI)
VCC2(12 V)
VCC1 (5 V)
Logic circuit
MB3773
RESET
1
2
3
4
8
7
6
5
RESET
CK
CT
30 kΩ
R3
NMI or port
GND
180 kΩ
10 kΩ
R6
R4
+
+
_
_
Comp. 1
1.2 kΩ
Comp. 2
R1
4.7 kΩ
R5
5.1 kΩ
R2
Example : Comp. 1, Comp. 2
: MB4204, MB47393
Notes : • The 5 V supply voltage is monitored by the MB3773.
• The 12 V supply voltage is monitored by the external circuit. Its output is connected to the NMI
terminal and, when voltage drops, Comp. 2 interrupts the logic circuit.
• Use VCC1 ( = 5 V) to power the comparators (Comp. 1 and Comp. 2) in the external circuit shown
above.
• The detection voltage of the VCC2 ( = 12 V) supply voltage is approximately 9.2 V/9.4 V and has
a hysteresis width of approximately 0.2 V.
VCC2 detection voltage and hysteresis width can be found using the following formulas:
R3 + (R4 // R5)
→ Detection voltage
× VREF
V2H =
V2L =
R4 // R5
R3 + R5
R5
(Approximately 9.4 V in the above illustration)
(Approximately 9.2 V in the above illustration)
× VREF
→ Hysteresis width VHYS = V2H − V2L
15
MB3773
EXAMPLE 5: Monitoring Two Supply Voltages (with hysteresis and reset output)
VCC2 (12 V)
VCC1 (5 V)
20 kΩ
R6
Logic circuit
RESET
MB3773
1
2
3
4
8
7
6
5
RESET
30 kΩ
R3
Diode
CT
CK
GND
180 kΩ
R4
+
+
_
_
Comp. 1
1.2 kΩ
R1
Comp. 2
5.1 kΩ
R2
4.7 kΩ
R5
Example : Comp. 1, Comp. 2
: MB4204, MB47393
Notes : • When either 5 V or 12 V supply voltage decreases below its detection voltage (VSL),
the MB3773 RESET terminal is set to High and the MB3773 RESET terminal is set to Low.
• Use VCC1 ( = 5 V) to power the comparators (Comp. 1 and Comp. 2) in the external circuit shown
above.
• The detection voltage of the VCC2 ( = 12 V) supply voltage is approximately 9.2 V/9.4 V and has a
hysteresis width of approximately 0.2 V. For the formulas for finding hysteresis width and detection
voltage, refer to section 4.
16
MB3773
EXAMPLE 6: Monitoring Low voltage and Overvoltage Monitoring (with hysteresis)
VCC (5 V)
20 kΩ
R6
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
30 kΩ
R3
Diode
CT
GND
180 kΩ
R4
+
_
+
_
Comp. 1
1.2 kΩ
R1
Comp. 2
5.6 kΩ
R6
4.7 kΩ
R5
Example : Comp. 1, Comp. 2
: MB4204, MB47393
RESET
VCC
0
V2L V2H
V1L V1H
Notes : • Comp. 1 and Comp. 2 are used to monitor for overvoltage while the MB3773 is used to monitor
for low voltage. Detection voltages V1L/V1H at the time of low voltage are approximately 4.2 V/4.3 V.
Detection voltages V2L/V2H at the time of overvoltage are approximately 6.0 V/6.1 V.
For the formulas for finding hysteresis width and detection voltage, see EXAMPLE 4.
• Use VCC ( = 5 V) to power the comparators (Comp. 1 and Comp. 2) in the external circuit shown
above.
17
MB3773
EXAMPLE 7: Monitoring Supply Voltage Using Delayed Trigger
VCC
VCC
5V
4V
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
CT
C1
GND
Note : Adding voltage such as shown in the figure to VCC increases the minimum input pulse
width by 50 µs (C1 = 1000 pF).
18
MB3773
EXAMPLE 8: Stopping Watch-dog Timer (Monitoring only supply voltage)
These are example application circuits in which the MB3773 monitors supply voltage alone without resetting the
microprocessor even if the latter, used in standby mode, stops sending the clock pulse to the MB3773.
• The watch-dog timer is inhibited by clamping the CT terminal voltage to VREF.
The supply voltage is constantly monitored even while the watch-dog timer is inhibited.
For this reason, a reset signal is output at the occurrence of either instantaneous disruption or a sudden drop
to low voltage.
Note that in application examples (a) and (b), the hold signal is inactive when the watch-dog timer is inhibited at
the time of resetting.
If the hold signal is active when tie microprocessor is reset, the solution is to add a gate, as in examples (c)
and (d).
(a) Using NPN transistor
VCC(5 V)
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
HALT
GND
R2=1 kΩ
R1=1 MΩ
CT
(b) Using PNP transistor
VCC (5 V)
MB3773
Logic circuit
1
8
7
6
5
RESET
RESET
CK
2
3
4
HALT
GND
R2=1 kΩ
R1=51 kΩ
CT
(Continued)
19
MB3773
(Continued)
(c) Using NPN transistor
VCC (5 V)
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
R1=1 MΩ
HALT
GND
R2=1 kΩ
CT
(d) Using PNP transistor
VCC (5 V)
MB3773
Logic circuit
1
2
3
4
8
7
6
5
RESET
RESET
CK
R1=51 kΩ
HALT
GND
R2=1 kΩ
CT
20
MB3773
EXAMPLE 9: Reducing Reset Hold Time
VCC( = 5 V)
VCC ( = 5 V)
MB3773
MB3773
Logic circuit
RESET
Logic circuit
1
2
3
4
1
2
3
4
8
7
6
5
8
7
6
5
RESET
RESET
CK
RESET
CK
CT
CT
GND
GND
(a) TPR reduction method
(b) Standard usage
Notes : • RESET is the only output that can be used.
• Standard TPR, TWD and TWR value can be found using the following formulas.
Formulas: TPR (ms) =: 100 × CT (µF)
TWD (ms) =: 100 × CT (µF)
TWR (ms) =: 16 × CT (µF)
• The above formulas become standard values in determining TPR, TWD and TWR.
Reset hold time is compared below between the reduction circuit and the standard circuit.
CT = 0.1 µF
TPR reduction circuit
10 ms
Standard circuit
100 ms
TPR =:
TWD =:
TWR =:
10 ms
10 ms
1.6 ms
2.0 ms
21
MB3773
EXAMPLE 10: Circuit for Monitoring Multiple Microprocessor
VCC ( = 5 V)
FF1
FF2
FF3
S
S
S
D1 Q1
D2 Q2
D3 Q3
CK1 Q1
CK2 Q2
CK3 Q3
R
R
R
R2
R1
*
*
*
RESET
RESET
RESET
RESET
CK
RESET
CK
RESET
CK
GND
GND
GND
1
2
8
7
3
4
6
5
CT
Figure 1
*: Microprocessor
Notes : •
MB3773
connects from FF1 and FF2 outputs Q1 and Q2 to the NOR input.
• Depending on timing, these connections may not be necessary.
• Example : R1 = R2 = 2.2 kΩ
CT = 0.1 µF
CK1
Q1
CK2
Q2
CK3
Q3
NOR
Output
Figure 2
22
MB3773
Description of Application Circuits
Using one MB3773, this application circuit monitors multiple microprocessor in one system. Signals from each
microprocessor are sent to FF1, FF2 and FF3 clock inputs. Figure 2 shows these timings. Each flip-flop operates
using signals sent from microprocessor as its clock pulse. When even one signal stops, the relevant receiving
flip-flop stops operating. As a result, cyclical pulses are not generated at output Q3. Since the clock pulse stops
arriving at the CK terminal of the MB3773, the MB3773 generates a reset signal.
Note that output Q3 frequency f will be in the following range, where the clock frequencies of CK1, CK2 and CK3
are f1, f2 and f3 respectively.
1
f0
1
f
1
1
1
---- --
≤
≤
+
+
---- ---- ----
f1 f2 f3
where f0 is the lowest frequency among f
1
, f2
and f .
3
23
MB3773
EXAMPLE 11: Circuit for Limiting Upper Clock Input Frequency
VCC (5 V)
R2
RESET
1
2
3
4
8
7
6
5
RESET
CT
R1=10 kΩ
CK
GND
Tr1
C2
Notes : • This is an example application to limit upper frequency fH of clock pulses sent from
the microprocessor.
If the CK cycle sent from the microprocessor exceeds fH, the circuit generates a reset signal.
(The lower frequency has already been set using CT.)
• When a clock pulse such as shown below is sent to terminal CK, a short T2 prevents C2 voltage
from reaching the CK input threshold level (=: 1.25 V), and will cause a reset signal to be output.
The T1 value can be found using the following formula :
T1=: 0.3 C2R2
where VCC = 5 V, T3 ≥ 3.0 µs, T2 ≥ 20 µs
T2
CK waveform
T3
C2 voltage
T1
Example : Setting C and R allow the upper T1 value to be set (Refer to the table below).
C
R
T1
0.01 µF
0.1 µF
10 kΩ
10 kΩ
30 µs
300 µs
24
MB3773
■ NOTES ON USE
• Take account of common impedance when designing the earth line on a printed wiring board.
• Take measures against static electricity.
- For semiconductors, use antistatic or conductive containers.
- When storing or carrying a printed circuit board after chip mounting, put it in a conductive bag or container.
- The work table, tools and measuring instruments must be grounded.
- The worker must put on a grounding device containing 250 kΩ to 1 MΩ resistors in series.
• Do not apply a negative voltage
- Applying a negative voltage of −0.3 V or less to an LSI may generate a parasitic transistor, resulting in
malfunction.
■ ORDERING INFORMATION
Part number
MB3773PF-■■■
MB3773PF-■■■E1
Package
Remarks
8-pin plastic SOP
(FPT-8P-M01)
Conventional version
8-pin plastic SOP
(FPT-8P-M01)
Lead Free version
■ RoHS Compliance Information of Lead (Pb) Free version
The LSI products of Fujitsu Microelectronics with “E1” are compliant with RoHS Directive , and has observed
the standard of lead, cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB) , and polybro-
minated diphenyl ethers (PBDE) .
The product that conforms to this standard is added “E1” at the end of the part number.
■ MARKING FORMAT (Lead Free version)
Lead-Free version
3773
E1XXXX
XXX
INDEX
25
MB3773
■ LABELING SAMPLE (Lead free version)
lead-free mark
JEITA logo JEDEC logo
MB123456P - 789 - GE1
(3N) 1MB123456P-789-GE1 1000
G
Pb
(3N)2 1561190005 107210
QC PASS
PCS
1,000
MB123456P - 789 - GE1
ASSEMBLED IN JAPAN
2006/03/01
MB123456P - 789 - GE1
1/1
1561190005
0605 - Z01A 1000
Lead-Free version
26
MB3773
■ MB3773PF-■■■E1 RECOMMENDEDCONDITIONSOF MOISTURESENSITIVITYLEVEL
Item
Condition
IR (infrared reflow) , Manual soldering (partial heating method)
2 times
Mounting Method
Mounting times
Please use it within two years after
Before opening
Manufacture.
From opening to the 2nd
Less than 8 days
reflow
Storage period
When the storage period after
opening was exceeded
Please processes within 8 days
after baking (125 °C, 24h)
Storage conditions
5 °C to 30 °C, 70%RH or less (the lowest possible humidity)
[Temperature Profile for FJ Standard IR Reflow]
(1) IR (infrared reflow)
H rank : 260 °C Max.
260 °C
255 °C
170 °C
to
190 °C
(b)
(c)
(d)
(e)
RT
(a)
(d')
(a) Temperature Increase gradient : Average 1 °C/s to 4 °C/s
(b) Preliminary heating : Temperature 170 °C to 190 °C, 60s to 180s
(c) Temperature Increase gradient : Average 1 °C/s to 4 °C/s
(d) Actual heating
(d’)
: Temperature 260 °C MAX; 255 °C or more, 10s or less
: Temperature 230 °C or more, 40s or less
or
Temperature 225 °C or more, 60s or less
or
Temperature 220 °C or more, 80s or less
(e) Cooling
: Natural cooling or forced cooling
Note : Temperature : the top of the package body
(2) Manual soldering (partial heating method)
Conditions : Temperature 400 °C MAX
Times
: 5 s max/pin
27
MB3773
■ PACKAGE DIMENSION
8-pin plastic SOP
Lead pitch
1.27 mm
5.3 × 6.35 mm
Gullwing
Package width
package length
×
Lead shape
Sealing method
Mounting height
Weight
Plastic mold
2.25 mm MAX
0.10 g
Code
(Reference)
P-SOP8-5.3×6.35-1.27
(FPT-8P-M01)
8-pin plastic SOP
(FPT-8P-M01)
Note 1) *1 : These dimensions include resin protrusion.
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
*1 6.35 +–00..2205 .250 –+..000180
0.17 –+00..0043
.007 +–..000021
8
5
*2 5.30±0.30 7.80±0.40
(.209±.012) (.307±.016)
INDEX
Details of "A" part
2.00 +–00..1255
(Mounting height)
.079 +–..000160
0.25(.010)
0~8˚
"A"
1
4
1.27(.050)
0.47±0.08
(.019±.003)
M
0.13(.005)
0.50±0.20
(.020±.008)
0.10 +–00..0150
.004 +–..000024
0.60±0.15
(Stand off)
(.024±.006)
0.10(.004)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2002 FUJITSU LIMITED F08002S-c-6-7
28
MB3773
MEMO
29
MB3773
MEMO
30
MB3773
MEMO
31
FUJITSU MICROELECTRONICS LIMITED
Shinjuku Dai-Ichi Seimei Bldg. 7-1, Nishishinjuku 2-chome, Shinjuku-ku,
Tokyo 163-0722, Japan
Tel: +81-3-5322-3347 Fax: +81-3-5322-3387
http://jp.fujitsu.com/fml/en/
For further information please contact:
North and South America
Asia Pacific
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
FUJITSU MICROELECTRONICS ASIA PTE LTD.
151 Lorong Chuan, #05-08 New Tech Park,
Singapore 556741
Tel: +65-6281-0770 Fax: +65-6281-0220
http://www.fujitsu.com/sg/services/micro/semiconductor/
Europe
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm.3102, Bund Center, No.222 Yan An Road(E),
Shanghai 200002, China
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen,
Germany
Tel: +86-21-6335-1560 Fax: +86-21-6335-1605
http://cn.fujitsu.com/fmc/
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road
Tsimshatsui, Kowloon
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Hong Kong
Tel: +852-2377-0226 Fax: +852-2376-3269
http://cn.fujitsu.com/fmc/tw
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://www.fmk.fujitsu.com/
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS
does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporat-
ing the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS
or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect
to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in
weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising
in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current
levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of
the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited Strategic Business Development Dept.
相关型号:
![](http://pdffile.icpdf.com/pdf1/p00070/img/page/MB3775_369337_files/MB3775_369337_1.jpg)
![](http://pdffile.icpdf.com/pdf1/p00070/img/page/MB3775_369337_files/MB3775_369337_2.jpg)
MB3775M
Dual Switching Controller, Voltage-mode, 0.75A, 500kHz Switching Freq-Max, PDIP16, PLASTIC, DIP-16
FUJITSU
![](http://pdffile.icpdf.com/pdf2/p00237/img/page/MB3775PFV-XX_1391422_files/MB3775PFV-XX_1391422_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00237/img/page/MB3775PFV-XX_1391422_files/MB3775PFV-XX_1391422_2.jpg)
MB3775PF-XXX
Dual Switching Controller, 0.075A, 500kHz Switching Freq-Max, PDSO16, 5.30 X 10.15 MM, 2.25 MM HEIGHT, 1.27 MM PITCH, PLASTIC, SOP-16
FUJITSU
![](http://pdffile.icpdf.com/pdf2/p00237/img/page/MB3775PFV-XX_1391422_files/MB3775PFV-XX_1391422_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00237/img/page/MB3775PFV-XX_1391422_files/MB3775PFV-XX_1391422_2.jpg)
MB3775PF-XXXE1
Dual Switching Controller, 0.075A, 500kHz Switching Freq-Max, PDSO16, 5.30 X 10.15 MM, 2.25 MM HEIGHT, 1.27 MM PITCH, ROHS COMPLIANT, PLASTIC, SOP-16
FUJITSU
![](http://pdffile.icpdf.com/pdf2/p00237/img/page/MB3775PFE1_1391421_files/MB3775PFE1_1391421_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00237/img/page/MB3775PFE1_1391421_files/MB3775PFE1_1391421_2.jpg)
MB3775PFE1
Dual Switching Controller, Voltage-mode, 0.05A, 500kHz Switching Freq-Max, BIPolar, PDSO16
CYPRESS
©2020 ICPDF网 联系我们和版权申明