C6M35 [SPSEMI]
Gas Discharge Tube C6M Series;
| 型号： | C6M35 |
| 厂家： | 
StarHope |
| 描述： | Gas Discharge Tube C6M Series |
| 文件： | 总3页 (文件大小：161K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
S P S E M I
ꢀ ꢁ ꢂ ꢃ
GDT/C6M Series
Gas Discharge Tube
C6M Series
Features
Electronic stability
Small volume, easy to placement machine operation
Large flow capacity, impact resistant ability
Static electricity capacity, good insulation
Reaction speed is 50 ns - 150 ns
Applications
ADSL MODEM、FAX、TELEPHONE
RS485、RS232、CAN level of protection
CATV
Power supply prevents thunder common-mode protection
Marking Code
C6M09R
C6M09
Logo
Logo
Marking Code
Marking Code
With Wire
Without Wire
Product Name
C 6 M 0 9 R X
Internal Code(Default)
R: With Lead
Default: No Lead
Nom. DC spark-over
voltage Vs
09:90V
15:150V
47:470V
150:1500V
Electrical Characteristics
K: 3KA
L: 5KA
M:10KA
H: 20KA
B5: 2R/5*5mm
B8: 2R/8*6mm
C6: 3R/6*8mm
C7: 3R/7*11.5mm
C8: 3R/8*10mm
Page 1 of 3
www.spsemi.cn
REV.2017.04.06
S P S E M I
ꢀ ꢁ ꢂ ꢃ
GDT/C6M Series
Dimensions
8± 0.2
Φ6± 0.2
Φ0.8± 0.1
4.4± 0.3
4.4± 0.3
Dimensions in millimeters
Electrical Characteristics
Nom.
Nom.
Nom.
Impulse
Discharge
Current
(@8/20μs)
(KA)
DC
Spark-over
Voltage
Impulse
Spark-over
Voltage
(@1KV/μs)
(V)
Insulation
Resistance
Alternating Impulse
Discharge Discharge
Current Current
(@50HZ) (@8/20μs)
Part Number
Capacitance
(pF)
(@100V/s）
(V)
Without
Wire
With
Wire
(@DC)
(V)
(GΩ)
(A)
10
10
10
10
10
10
10
(KA)
10
10
10
10
10
10
10
25
C6M07R C6M07
C6M09R C6M09
C6M15R C6M15
C6M23R C6M23
C6M35R C6M35
C6M47R C6M47
C6M60R C6M60
75± 20±
90± 20±
≦600
≦600
≦650
≦650
≦700
≦750
≦950
5×2
5×2
5×2
5×2
5×2
5×2
5×2
>1
>1
>1
>1
>1
>1
>1
<1
<1
<1
<1
<1
<1
<1
50
50
150± 20±
230± 20±
350± 20±
470± 20±
600± 20±
100
100
250
250
Packaging Speci Cations
Packaging:100 pieces bulk
Initial Characteristics
Specification
Test Item
Test Method
Add and measure the DC Voltage gradually
Maxto get the discharge threshold voltage.
The measuring current is 1mA/1 second max.（1sec）.(1mA)
DC-Spark-Over Voltage
Vs
It depands on each spec.
Measure the insulation resistance of two end of
leadwire under the specified DC voltage.
Insulation
Resistance
100MΩ min.
0.8pF max.
Electrostatic Capacitance under the test condition
of 1KHz,DC 6V(max).
Capacitance C(pF)
Page 2 of 3
www.spsemi.cn
REV.2017.04.06
S P S E M I
ꢀ ꢁ ꢂ ꢃ
GDT/C6M Series
Surge Characteristics
Specification
Test Item
Test Method
In the glass tube ends in 8/20 us surge tester, applying the model that
corresponds to the impact resistance current, time interval for the
60 s of plus or minus the test 5 times. Test the dc voltage,
DC spark-over voltage
JSE: △Vs/Vs≦30%
Surge withstand capability
insulation resistance, static capacitance and check the appearance.
Apply 10KV voltage charged in 1500pF condenser and
apply the current to the specimen,200 times at 10
seconds of intervals.
Within standard mentioned in
Initial Characteristics.
Surge life test
Enviromental Characteristics
Specification
Test Item
Test Method
After -40 3℃
(1000hrs) / room temp.,normal humidity(4 hrs)
cycle, measure the properties.
Within standard mentioned in
Initial Characteristics.
Cold resistance
Heat resistance
After 125 2℃
(1000hrs) / room temp.,normal humidity(4 hrs)
cycle, measure the properties.
Within standard mentioned in
Initial Characteristics.
After 85 2℃
RH85%(1000hrs) / room temp.,normal humidity(4
hrs) cycle, measure the properties.
Within standard mentioned in
Initial Characteristics.
Temperature resistance
Temperature period
Tensile strength
25 times repetition of cycle -40 3℃
(30 Min.),roon temp., (4 Min.), 125 2℃(30Min.),
room temp., normal humidity(4hrs) .
Within standard mentioned in
Initial Characteristics.
Apply 2.5kgs load approximately 30 seconds, then check
for pull-out and breaking of the lead wire.
Within standard mentioned in
Initial Characteristics.
Bend the lead wire, with jig which radius is 0.75~0.8mm, at the point
of 2mm from the body, under 0.25 kgs load applied at the right angle
the direction of theamis and get the bent lead wire back to its
original poing after the procedure was repeated 2times.
Within standard mentioned in
Initial Characteristics.
Bending strength
Apply flux and immerse in molten solder, up to the point of
). Wash
Resistance to soldering
attachment
（by solder dip）
Lead wire is evenly covered by
solder over 90%.
3mm from the body,for 5 sec. (235
5
the leadwire and check for soldering adhesion.
Resistance to soldering
heat
（by solder dip）
Apply flux and immerse in molten solder, up to the point of 3mm
from the body,for 5 sec. (235℃ 5℃). Wash the leadwire
and check forsoldering adhesion.)
Within standard mentioned in
Initial Characteristics.
Page 3 of 3
www.spsemi.cn
REV.2017.04.06
相关型号：
©2020 ICPDF网 联系我们和版权申明