SST89C58-33-AC-TQJ [SST]
FlashFlex51 MCU; FlashFlex51 MCU
| 型号： | SST89C58-33-AC-TQJ |
| 厂家： | 
SILICON STORAGE TECHNOLOGY, INC |
| 描述： | FlashFlex51 MCU |
| 文件： | 总50页 (文件大小：413K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
FEATURES:
•
•
•
•
•
•
•
•
High Current Drive on Port 1 (5, 6, 7) pins
Three 16-bit Timer/Counter
•
Multi-Purpose 8-bit 8051 Family Compatible
Microcontroller Unit (MCU) with Embedded
SuperFlash Memory
1
Programmable Serial Port (UART)
Six Interrupt Sources at 2 Priority Levels
Selectable Watchdog Timer (WDT)
Four 8-bit I/O Ports (32 I/O Pins)
•
Fully Software and Development Toolset
Compatible as well as Pin-For-Pin Package
Compatible with Standard 8xC5x
Microcontrollers
2
3
•
•
256 Bytes Register/Data RAM
TTL- and CMOS-Compatible Logic Levels
Extended Power-Saving Modes
20/36 KByte Embedded High Performance
Flexible SuperFlash EEPROM
4
– Idle Mode
– Power Down Mode with External Interrupt
Wake-up
– One 16/32 KByte block (128-Byte
sector size)
– One 4 KByte block (64-Byte sector size)
– Individual Block Security Lock with Softlock™
feature
– 87C5x Programmer Compatible
– Concurrent Operation during In-Application
Programming™(IAP™)
– Memory Re-Mapping for Interrupt Support
during IAP
5
– Standby (Stop Clock) Mode
•
•
•
•
High Speed Operation at 5 Volts (0 to 33MHz)
Low Voltage (2.7V) Operation (0 to 12MHz)
PDIP-40, PLCC-44 and TQFP-44 Packages
Temperature Ranges:
6
7
– Commercial (0°C to +70°C)
– Industrial (-40°C to +85°C)
•
Support External Address Range up to
64 KByte of Program and Data Memory
8
PRODUCT DESCRIPTION
via a standard 87C5x OTP EPROM programmer fitted
with a special adapter and firmware for SST89C54/58
devices. During the power-on reset, the SST89C54/58
can be configured as a master for source code storage
or as a slave to an external host for In-Application
Programming (IAP) operation. SST89C54/58 is de-
signed to be programmed “In-System” and “In-Applica-
tion” on the printed circuit board for maximum flexibility.
The device is pre-programmed with a sample bootstrap
loader in the memory (see Note 1), demonstrating the
initial user program code loading or subsequent user
code updating via the “IAP” operation.
SST89C54 and SST89C58 are members of the
FlashFlex51 family of 8-bit microcontrollers. The
FlashFlex51 family is a family of embedded
microcontrollerproductsdesignedandmanufacturedon
the state-of-the-art SuperFlash CMOS semiconductor
process technology.
9
10
11
12
13
14
15
16
As a member of the FlashFlex51 controller family, the
SST89C54/58 uses the same powerful instruction set,
has the same architecture, and is pin-for-pin compatible
with standard 8xC5x microcontroller devices.
In addition to 20/36 KByte of SuperFlash EEPROM
program memory on-chip, the SST89C54/58 can ad-
dress up to 64 KByte of program memory external to the
chip. The SST89C54/58 have 256 x 8 bits of on-chip
RAM. Up to 64 KByte of external data memory (RAM)
can be addressed.
SST89C54/58 comes with 20/36 KByte of
integrated on-chip flash EEPROM program memory
using the patented and proprietary Silicon Storage
Technology, Inc. (SST) CMOS SuperFlash EEPROM
technology with the SST field enhancing tunneling
injector split-gate memory cells. The SuperFlash
memory is partitioned into 2 independent program
memory blocks. The primary SuperFlash Block 0 occu-
pies16/32KByteofinternalprogrammemoryspaceand
the secondary SuperFlash Block 1 occupies 4 KByte of
SST89C54/58’s internal program memory space. The 4
KByte secondary SuperFlash block can be mapped to
the highest or lowest location of the 64 KByte address
space; it can also be hidden from the program counter
and used as an independent EEPROM-like data
memory. The flash memory blocks can be programmed
Thehighlyreliable,patentedSuperFlashtechnologyand
memory cell architecture have a number of important
advantages for designing and manufacturing flash
EEPROMs, when compared with other approaches.
These advantages translate into significant cost and
reliability benefits for our customers.
Note 1: The sample bootstrap loader is for the user’s reference and
convenience only. SST does not guarantee the functionality
or the usefulness of the sample bootstrap loader. Chip-Erase
or Block-Erase operations will erase the pre-programmed
sample code.
© 2000 Silicon Storage Technology, Inc. The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc. FlashFlex, In-Application Programming, IAP and SoftLock are
344-2 8/00 trademarks of Silicon Storage Technology, Inc. These specifications are subject to change without notice.
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE OF CONTENTS
PRODUCT FEATURES ......................................................................................................................................... 1
PRODUCT DESCRIPTION .................................................................................................................................... 1
FUNCTIONAL BLOCKS ......................................................................................................................................... 4
Functional Block Diagram ............................................................................................................................... 4
PIN ASSIGNMENTS .............................................................................................................................................. 5
Pin Descriptions .............................................................................................................................................. 6
MEMORY ORGANIZATION ................................................................................................................................... 8
Program Memory ............................................................................................................................................ 8
Memory Re-Mapping..................................................................................................................................... 10
Activation and Deactivation of Memory Re-Mapping ............................................................................... 11
Data Memory ................................................................................................................................................ 13
Special Function Registers (SFR) ................................................................................................................. 13
CPU Related SFRs.................................................................................................................................. 13
Flash Memory Programming SFRs.......................................................................................................... 14
Watchdog Timer SFRs ............................................................................................................................ 17
Timer/Counters SFRs .............................................................................................................................. 18
Interface SFRs......................................................................................................................................... 18
FLASH MEMORY PROGRAMMING .................................................................................................................... 18
External Host Programming Mode ................................................................................................................ 18
Product Identification ............................................................................................................................... 20
External Host Mode Commands .............................................................................................................. 20
External Host Mode Clock Source ........................................................................................................... 21
Arming Command.................................................................................................................................... 21
Programming a SST89C54/58 ................................................................................................................. 21
Flash Operation Status Detection (Ext. Host Handshake) ....................................................................... 22
In-Application Programming Mode ................................................................................................................ 26
In-Application Programming Mode Clock Source..................................................................................... 26
IAP Enable Bit ......................................................................................................................................... 26
In-Application Programming Mode Commands........................................................................................ 26
Polling...................................................................................................................................................... 29
Interrupt Temination................................................................................................................................. 30
TIMERS/COUNTERS........................................................................................................................................... 31
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
2
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
SERIAL I/O (UART).............................................................................................................................................. 31
WATCHDOG TIMER ............................................................................................................................................ 32
1
SECURITY LOCK ................................................................................................................................................ 32
2
Hard Lock................................................................................................................................................. 32
SoftLock ................................................................................................................................................... 32
3
Status of the Security Lock ........................................................................................................................... 33
RESET ................................................................................................................................................................ 34
Power-On Reset ........................................................................................................................................... 34
POWER-SAVING MODES ................................................................................................................................... 35
CLOCK INPUT OPTIONS .................................................................................................................................... 37
4
5
ELECTRICAL SPECIFICATION ........................................................................................................................... 38
Absolute Maximum Ratings .......................................................................................................................... 38
Operation Range........................................................................................................................................... 38
6
Reliability Characteristics .............................................................................................................................. 38
DC Electrical Characteristics......................................................................................................................... 39
AC Electrical Characteristics ......................................................................................................................... 42
Explanation Of Symbols .......................................................................................................................... 43
External Clock Drive ................................................................................................................................ 44
Serial Port Timing - Shift Register Mode .................................................................................................. 45
7
8
9
PRODUCT ORDERING INFORMATION ............................................................................................................. 46
Part Number Valid Combinations .................................................................................................................. 46
10
11
12
13
14
15
16
PART NUMBER CROSS REFERENCE GUIDE .................................................................................................. 47
PACKAGING DIAGRAMS .................................................................................................................................... 48
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
3
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
FUNCTIONAL BLOCKS
FUNCTIONAL BLOCK DIAGRAM
Program/Erase
SuperFlash
EEPROM
4K x 8
8
SuperFlash EEPROM
16/32K x 8
Port 0
I/O
& IAP
Control
8
T0
RST
Power Mode
Management
I/O
SFRs
Port 1
V
SS
T1
T2
V
DD
CPU
8
ALE/PROG#
PSEN#
EA#
I/O
Security
Lock
Bus Controller
Oscillator
Port 2
WDT
8
I/O
Mode Interrupt
Control Control
RAM
256 x 8
8-bit
UART
Port 3
&
Timing
344 ILL B1.1
XTAL1 XTAL2
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
4
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
PIN ASSIGNMENTS
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
V
DD
(T2) P1.0
(T2 Ex) P1.1
P1.2
1
1
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA#
2
3
P1.3
4
44 43 42 41 40 39 38 37 36 35 34
33
2
P1.4
5
1
P1.5
P1.6
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA#
P1.5
6
32
31
30
29
28
27
26
25
24
23
2
P1.6
7
40-Pin PDIP
Top View
3
P1.7
P1.7
8
3
4
RST
RST
9
5
(RXD) P3.0
NC
(RXD) P3.0
(TXD) P3.1
(INT0#) P3.2
(INT1#) P3.3
(T0) P3.4
(T1) P3.5
(WR#) P3.6
(RD#) P3.7
XTAL2
10
11
12
13
14
15
16
17
18
19
20
44-Pin TQFP
Top View
6
ALE/PROG#
PSEN#
NC
4
7
(TXD) P3.1
(INT0#) P3.2
(INT1#) P3.3
(T0) P3.4
(T1) P3.5
ALE/PROG#
PSEN#
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P2.4 (A12)
P2.3 (A11)
P2.2 (A10)
P2.1 (A9)
P2.0 (A8)
8
9
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
5
10
11
12 13 14 15 16 17 18 19 20 21 22
6
XTAL1
V
SS
7
344 ILL F18.1
344 ILL F19.1
FIGURE 1: PIN ASSIGNMENTS FOR 40-PIN PLASTIC DIP
FIGURE 2: PIN ASSIGNMENTS FOR 44-PIN TQFP
8
PI-PACKAGE
TQJ-PACKAGE
9
10
11
12
13
14
15
16
6
5
4
3
2
1
44 43 42 41 40
7
P1.5
P1.6
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA#
39
38
37
36
35
34
33
32
31
30
29
8
9
P1.7
10
11
12
13
14
15
16
17
RST
(RXD) P3.0
NC
44-Pin PLCC
Top View
NC
(TXD) P3.1
(INT0#) P3.2
(INT1#) P3.3
(T0) P3.4
(T1) P3.5
ALE/PROG#
PSEN#
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
18 19 20 21 22 23 24 25 26 27 28
344 ILL F20.1
FIGURE 3: PIN ASSIGNMENTS FOR 44-PIN PLCC
NJ-PACKAGE
Note: NC pins must be left unconnected.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
5
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 1: PIN DESCRIPTIONS
Symbol
Type1
Name and Functions
P0[7:0]
I/O1
Port 0: Port 0 is an 8-bit open drain bi-directional I/O port. As an output port each
pin can sink several LS TTL inputs. Port 0 pins that have 1’s written to them
float, and in that state can be used as high-impedance inputs. Port 0 is also the
multiplexed low-order address and data bus during accesses to external
memory. In this application it uses strong internal pull-ups when transitioning
to 1’s. Port 0 also receives the code bytes during FLASH MEMORY
programming, and outputs the code bytes during program verification. External
pull-ups are required during program verification.
P1[7:0]
I/O with internal Port 1: Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1
pull-ups
output buffers can drive LS TTL inputs. Port 1 pins that have 1’s written to them
are pulled high by the internal pull-ups, and in that state can be used as
inputs. As inputs, Port 1 pins that are externally pulled low will source current
(IIL, on the data sheet) because of the internal pull-ups. P1(5, 6, 7) have high
current drive of 16mA. Port 1 also receives the low-order address bytes during
FLASH MEMORY programming and program verification.
P1[0]
I
I
T2: (external count input to Timer/Counter 2), clock-out
P1[1]
T2EX: (Timer/Counter 2 capture/reload trigger and direction control)
P2[7:0]
I/O with internal Port 2: Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. Port 2 pins
pull-ups
that have 1’s written to them are pulled high by the internal pull-ups, and
in that state can be used as inputs. As inputs, Port 2 pins that are externally
pulled low will source current (IIL, on the data sheet) because of the internal
pull-ups. Port 2 sends the high-order address byte during fetches from external
Program memory and during accesses to external Data Memory that use 16-bit
address (MOVX@DPTR). In this application it uses strong internal pull-ups
when outputting 1’s. During accesses to external Data Memory that use 8-bit
addresses (MOVX@Ri), Port 2 sends the contents of the P2 Special Function
Register. Port 2 also receives some control signals and a partial of high-order
address bits during FLASH MEMORY programming and program verification.
P3[7:0]
I/O with internal Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 3
pull-ups
output buffers could drive LS TTL inputs. Port 3 pins that have 1’s written to them
are pulled high by the internal pull-ups, and in that state can be used as inputs.
As inputs, Port 3 pins that are externally pulled low will source current (IIL, on the
data sheet) because of the pull-ups. Port 3 also serves the functions of various
special features of the FlashFlex51 Family. Port 3 also receives some control
signals and a partial of high-order address bits during FLASH MEMORY
programming and program verification.
P3[0]
P3[1]
P3[2]
P3[3]
P3[4]
P3[5]
P3[6]
P3[7]
I
O
I
RXD: Serial input line
TXD: Serial output line
INT0#: External Interrupt 0
INT1#: External Interrupt 1
T0: Timer 0 external input
I
I
I
T1: Timer 1 external input
O
O
WR#: External Data Memory Write strobe
RD#: External Data Memory Read strobe
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
6
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
PIN DESCRIPTIONS (CONTINUED)
Symbol
Type1
Name and Functions
PSEN#
O/I
Program Store Enable: PSEN# is the Read strobe to External Program
Memory. When the SST89C54/58 are executing from Internal Program
Memory, PSEN# is inactive (high). When the device is executing code from
External Program Memory, PSEN# is activated twice each machine cycle,
except that two PSEN# activations are skipped during each access to External
Data Memory. While the RST input is continually held high (for more than ten
machine cycles), a forced high-to-low input transition on the PSEN# pin will bring
the device into the “External Host” mode for the internal flash memory
programming operation.
1
2
3
RST
I
I
Reset: A high logic state on this pin for two machine cycles (at least 24 oscillator
periods), while the oscillator is running resets the device. After a successful reset
is completed, if the PSEN# pin is driven by an input force with a high-to-low
transition while the RST input pin is continually held high, the device will enter the
“External Host” mode for the internal flash memory programming operation,
otherwise the device will enter the “Normal” operation mode.
4
5
EA#
External Access Enable: EA# must be connected to VSS in order to enable the
SST89C54/58 to fetch code from External Program Memory locations starting
at 0000h up to FFFFh. Note, however, that if the Security Lock is activated on
either block, the logic level at EA# is internally latched during reset. EA# must be
connected to VDD for internal program execution. The EA# pin can tolerate a high
voltage2 of 12V (see Electrical Specification).
6
7
ALE/PROG#
I/O
Address Latch Enable: ALE is the output signal for latching the low byte of the
address during accesses to external memory. This pin is also the programming
pulse input (PROG#).
8
XTAL1
XTAL2
I
Oscillator: Input and output to the inverting oscillator amplifier. XTAL1 is input to
O
internal clock generation circuits from an external clock source.
9
VDD
I
Power Supply: Supply voltage during normal, Idle, Power Down, and Standby
Mode operations.
Vss
I
Ground: Circuit ground. (0V reference)
10
11
12
13
14
15
16
344 PGM T1.6
Note: 1)
2)
I
= Input
O = Output
It is not necessary to receive a 12V programming supply voltage during flash programming.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
7
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
MEMORY ORGANIZATION
The 4K x8 secondary SuperFlash block is organized as
64 uniform sectors with sector address from A15 to A6.
Each sector contains 2 rows with row address from A15
to A5. Each row contains 32 Bytes with byte address
fromA4toA0.Figure4showsthesectororganizationfor
SST89C54/58.
The SST89C54/58 have separate address spaces for
program and data memory.
Program Memory
There are two internal flash memory blocks in the
SST89C54/58. The primary flash memory Block 0 has
16/32 KByte and occupies the address space 0000h to
3FFFh/7FFFh.ThesecondaryflashmemoryBlock1has
4 KByte and occupies the address space F000h to
FFFFh.
When internal code operation is enabled (EA# = 1), the
primary 16/32 KByte flash memory block is always
visible to the program counter for code fetching. Figures
5 and 6 show the program memory organizations for the
SST89C54/58.
When internal code operation is enabled (EA# = 1), the
secondary 4 KByte flash memory block is selectively
visible for code fetching. The secondary block is always
accessible through the SuperFlash mailbox registers:
SFCM, SFCF, SFAL, SFAH, SFDT and SFST. When bit
7 of the SuperFlash Configuration mailbox register
(SFCF[7]),SFRaddresslocationB1h,isset,thesecond-
ary 4 KByte block will be visible by program counter.
The16/32Kx8primarySuperFlashblockisorganizedas
128/256uniformsectorswithsectoraddressfromA15to
A7. Each sector contains 2 rows with row address from
A15toA6.Eachrowhas64Byteswithbyteaddressfrom
A5 to A0.
7FFFh
FFFFh
Sector 255
7F80h
Sector 63
FFC0h
4000h
89C58
3FFFh
Sector 127
3F80h
89C54
F03Fh
007Fh
Sector 0
Sector 0
0000h
F000h
Block 0 (16/32 KByte)
Block 1 (4 KByte)
344 ILL F47.6
Primary
Secondary
FIGURE 4: SECTOR ORGANIZATION
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
8
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
EA# = 1 & SFCF[7] = 1
EA# = 1 & SFCF[7] = 0
FFFFh
EA# = 0
1
FFFFh
FFFFh
4 KByte
INTERNAL
(Block 1)
F000h
EFFFh
2
48 KByte
EXTERNAL
3
64 KByte
44 KByte
EXTERNAL
EXTERNAL
4
5
4000h
3FFFh
4000h
3FFFh
6
16 KByte
16 KByte
INTERNAL
(Block 0)
INTERNAL
(Block 0)
7
0000h
0000h
0000h
344 ILL F21.1
8
FIGURE 5: SST89C54 PROGRAM MEMORY ORGANIZATION
9
10
11
12
13
14
15
16
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
9
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
EA# = 1 & SFCF[7] = 1
EA# = 1 & SFCF[7] = 0
FFFFh
EA# = 0
FFFFh
FFFFh
4 KByte
INTERNAL
(Block 1)
F000h
EFFFh
32 KByte
EXTERNAL
28 KByte
EXTERNAL
64 KByte
EXTERNAL
8000h
7FFFh
8000h
7FFFh
32 KByte
32 KByte
INTERNAL
(Block 0)
INTERNAL
(Block 0)
0000h
0000h
0000h
344 ILL F11.1
FIGURE 6: SST89C58 PROGRAM MEMORY ORGANIZATION
Memory Re-mapping
The SST89C54/58 memory re-mapping feature allows
users to reorganize internal Flash memory sectors so
that interrupts may be serviced when Block 0 of the
internal Flash is being programmed. Since Block 0
occupies the low order program address space of the
8051 architecture where the interrupt vectors reside,
those interrupt vectors will normally not be available
when Block 0 is being programmed.
SST89C54/58 provides four options of Memory Re-
mapping (Refer to Table 2). When the lowest 4 KBytes
are remapped, any program access within logical ad-
dress range 0000h – 0FFFh will have the 4 most signifi-
cant address bits forced to “1”, redirecting the access to
F000h – FFFFh. Note that the physical contents of the
re-mapped portion of Block 0 (i.e. physical locations
0000h – 0FFFh in the current example) will not be
accessible. Block 1 will still also be accessible through
F000h – FFFFh. Figures 7 and 8 show re-mapped
program memory organization for the SST89C54/58.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
10
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Activation and Deactivation of Memory Re-mapping
The contents of MAP_EN[1:0] are only updated accord-
ing to Re-Map[1:0] on a successful reset. Any subse-
quentalterationtotheRe-Map[1:0]bitswillnotautomati-
cally change the MAP_EN[1:0] bits without a reset.
Similarly, changes to MAP_EN[1:0] during program ex-
ecution will not change Re-Map[1:0] bits.
The actual amount of memory that is re-mapped is
controlledbyMAP_EN[1:0]bitsasshowninTable2.The
MAP_EN[1:0] bits are the same bits as SFCF[1:0]. The
MAP_EN[1:0]bitsareundersoftwarecontrolandcanbe
changed during program execution. Since changing re-
mapping will cause program re-location, it is advisable
that the instruction that changes the MAP_EN[1:0] be in
the portion of memory that is not affected by the re-
mapping change.
1
2
To deactivate memory re-mapping, a CHIP-ERASE op-
eration will revert Re-Map[1:0] to the default status of
“11”, disabling re-mapping. Programming 00b to
SFCF[1:0] register also deactivates memory re-map-
ping.TheeffectofprogrammingRe-Map[1:0]isavailable
only after the next reset. Refer to In-Application Mode
Commands section for more detailed information.
3
The MAP_EN[1:0] bits are initialized at Reset according
to the contents of two non-volatile register bits, Re-
Map[1:0](asshowninTable2).TheRe-Map[1:0]bitsare
programmed via PROG_RB1 and PROG_RB0 External
HostModecommands. RefertoExternalHostProgram-
ming Mode section for PROG_RB1 and PROG_RB0
commands.
4
5
6
TABLE 2: RE-MAPPING TABLE
Re-Map [1:0]1
MAP_EN2,3
Comments
7
11
00
Re-mapping is turned off. Program memory is in normal
configuration.
10
01
00
01
10
11
1 KByte of flash memory location is re-mapped. Program access
8
to location 0000h-03FFh is redirected to F000h – F3FFh.
2 KBytes of flash memory location are re-mapped. Program access
to location 0000h-07FFh is redirected to F000h – F7FFh.
9
4 KBytes of flash memory location is re-mapped. Program access
to location 0000h-0FFFh is redirected to F000h – FFFFh.
344 PGM T2.3
10
11
12
13
14
15
16
1 Re-Map[1:0] are nonvolatile registers which are examined only during Reset.
2 MAP_EN[1:0] are initialized according to Re-Map[1:0] during Reset.
3 MAP_EN[1:0] are located in SFCF[1:0], they determine the Re-Mapping configuration. They may be changed by the program at run time.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
11
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
EA# = 1 & SFCF[7] = 1 EA# = 1 & SFCF[7] = 0
SFCF [1:0] = 01/10/11 SFCF [1:0] = 01/10/11
FFFFh
FFFFh
4 KByte
INTERNAL
(Block 1)
F000h
EFFFh
48 KByte
EXTERNAL
44 KByte
EXTERNAL
4000h
3FFFh
4000h
3FFFh
15/14/12
KByte
15/14/12
KByte
INTERNAL
(Block 0)
INTERNAL
(Block 0)
1/2/4 KByte
1/2/4 KByte
INTERNAL
(Block 1)
INTERNAL
(Block 1)
0000h
0000h
344 ILL F35.3
FIGURE 7: SST89C54 RE-MAPPED PROGRAM MEMORY ORGANIZATION
EA# = 1 & SFCF[7] = 1 EA# = 1 & SFCF[7] = 0
SFCF [1:0] = 01/10/11 SFCF [1:0] = 01/10/11
FFFFh
FFFFh
4 KByte
INTERNAL
(Block 1)
F000h
EFFFh
32 KByte
EXTERNAL
28 KByte
EXTERNAL
8000h
7FFFh
8000h
7FFFh
31/30/28
KByte
31/30/28
KByte
INTERNAL
(Block 0)
INTERNAL
(Block 0)
1/2/4 KByte
1/2/4 KByte
INTERNAL
(Block 1)
INTERNAL
(Block 1)
0000h
0000h
344 ILL F36.1
FIGURE 8: SST89C58 RE-MAPPED PROGRAM MEMORY ORGANIZATION
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
12
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Data Memory
SST89C54/58 have 256 x 8 bits of on-chip RAM and can address up to 64 KBytes of external data memory.
1
Special Function Registers (SFR)
Most of the unique features of the FlashFlex51 microcontroller family are controlled by bits in special function registers
(SFRs) located in the FlashFlex51 SFR Memory Map shown below. Individual descriptions of each SFR are provided
and Reset values indicated in Tables 3A to 3E.
2
3
8 BYTES
F8
F0
E8
E0
D8
D0
C8
C0
B8
B0
A8
A0
98
90
88
80
FF
F7
EF
E7
DF
D7
CF
C7
BF
B7
AF
A7
9F
97
4
B*
ACC*
5
PSW*
T2CON*
WDTC*
IP*
P3*
IE*
RCAP2L RCAP2H TL2
TH2
6
SFCF SFCM SFAL SFAH SFDT SFST
7
P2*
SCON* SBUF
P1*
TCON* TMOD TL0
8F
87
TL1
TH0
TH1
8
P0*
SP
DPL
DPH
WDTD PCON
FlashFlex51 SFR Memory Map
* = Bit Addressable SFRs
All addresses are hexadecimal
9
344 ILL F23.1
10
11
12
13
14
15
16
SST89C54/58 Special Function Registers
TABLE 3A: CPU RELATED SFRS
Symbol Description
Direct
Bit Address, Symbol, or Alternative Port Function
RESET
LSBValue
Address MSB
ACC*
B*
Accumulator
B Register
E0h
F0h
ACC[7:0]
B[7:0]
00h
00h
00h
PSW*
Program Status
Word
D0h
CY
AC
F0
RS1
RS0
OV
F1
P
SP
Stack Pointer
81h
82h
SP[7:0]
07h
00h
DPL
Data Pointer
Low 0
DPL[7:0]
DPH[7:0]
DPH
Data Pointer
High 0
83h
00h
IE*
Interrupt Enable
Interrupt Priority
Power Control
A8h
B8h
87h
EA
-
-
-
-
ET2
PT2
-
ES0
ET1
PT1
GF1
EX1
PX1
GF0
ET0
PT0
PD
EX0
PX0
IDL
40h
IP*
PS
-
xx000000b
PCON
SMOD
0xxx0000b
344 PGM T3A.3
* = Bit Addressable SFRs
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
13
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 3B: FLASH MEMORY PROGRAMMING SFRS
Symbol Description
Direct
Address
B6h
Bit Address, Symbol, or Alternative Port Function
RESET
Value
MSB
LSB
SFST
SFCF
SuperFlash Status
SECD[2:0]
IAPEN
-
-
BUSY Flash_busy
-
-
xxx00000b
000000xxb
SuperFlash
Configuration
B1h
VIS
FIE
-
-
-
MAP_EN
SFCM
SuperFlash
Command
B2h
FCM
00h
SFDT
SFAL
SuperFlash Data
B5h
B3h
SuperFlash Data Register
00h
00h
SuperFlash
Address Low
SuperFlash Low Order Byte Address Register – A7 to A0 (SFAL)
SuperFlash High Order Byte Address Register – A15 to A8 (SFAH)
SFAH
SuperFlash
B4h
00h
Address High
344 PGM T3B.4
SuperFlash Status Register (SFST) (Read Only Register)
Location
7
6
5
4
3
2
1
0
Reset Value
0B6h
SECD2 SECD1 SECD0
–
Busy Flash_busy
–
–
xxx00000b
Symbol
Function
Security bit 1.
SECD2
SECD1
SECD0
Security bit 2.
Security bit 3.
Please refer to Table 8 for security lock options.
BUSY
Burst-Program completion polling bit.
1: Device is busy with flash operation.
0: Device is available for next Burst-Program operation.
Flash_busy
Flash operation completion polling bit.
1: Device is busy with flash operation.
0: Device has fully completed the last command, including Burst-Program.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
14
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
SuperFlash Configuration Register (SFCF)
Location
7
6
5
4
3
2
1
0
Reset Value
1
0B1h
VIS
IAPEN
–
–
–
–
MAP_EN1 MAP_EN0 000000xxb
Symbol
VIS
Function
Upper flash block visibility.
2
1: 4 KByte flash block visible from F000-FFFF.
0: 4 KByte flash block not visible.
3
IAPEN
Enable IAP operation.
1: IAP commands are enabled.
0: IAP commands are disabled.
4
MAP_EN1
MAP_EN0
Map enable bit 1.
Map enable bit 0.
5
MAP_EN[1:0] are initialized to default value according to Re-map [1:0] during Reset.
Refer to Table 2.
6
SuperFlash Command Register (SFCM)
Location
7
6
5
4
3
2
1
0
Reset Value
7
0B2h
FIE
FCM6
FCM5
FCM4
FCM3
FCM2
FCM1
FCM0
00000000b
8
Symbol
FIE
Function
Flash Interrupt Enable.
1: INT1# is re-assigned to signal IAP operation completion.
External INT1# interrupts are ignored.
0: INT1# is not reassigned.
9
FCM[6:0]
Flash operation command.
000_0001b Chip-Erase.
000_0110b Burst-Program.
000_1011b Sector-Erase.
000_1100b Byte-Verify. (1)
000_1101b Block-Erase.
000_1110b Byte-Program.
10
11
12
13
14
15
16
All other combinations are not implemented, and reserved for future use.
(1) Byte-Verify has a single machine cycle latency and will not generate any INT1# interrupt regardless of FIE.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
15
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
SuperFlash Data Register (SFDT)
Location
7
6
5
4
3
2
1
0
Reset Value
0B5h
SuperFlash Data Register
00000000b
Symbol
SFDT
Function
Mailbox register for interfacing with flash memory block (Data register).
SuperFlash Address Registers (SFAL)
Location
7
6
5
4
3
2
1
0
Reset Value
0B3h
SuperFlash Low Order Byte Address Register
00000000b
Symbol
SFAL
Function
Mailbox register for interfacing with flash memory block. (Low order address register).
SuperFlash Address Registers (SFAH)
Location
7
6
5
4
3
2
1
0
Reset Value
0B4h
SuperFlash High Order Byte Address Register
00000000b
Symbol
SFAH
Function
Mailbox register for interfacing with flash memory block. (High order address register).
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
16
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 3C: WATCHDOG TIMER SFRS
WDTC* Watchdog Timer
Control
C0h
-
-
-
-
WDRE WDTS WDT SWDT
WDRL
X0h
1
WDTD Watchdog Timer
Data/Reload
86h
00h
344 PGM T3C.1
* = Bit Addressable SFRs
2
3
Watchdog Timer Control Register (WDTC)
Location
7
6
5
4
3
2
1
0
Reset Value
4
0C0h
–
–
–
–
WDRE
WDTS
WDT
SWDT
00000000b
5
Symbol
Function
WDRE
Watchdog timer reset enable.
1: Enable watchdog timer reset.
2: Disable watchdog timer reset.
6
WDTS
Watchdog timer reset flag.
1: Hardware sets the flag on watchdog overflow.
0: External hardware reset clears the flag.
Flag can also be cleared by writing a 1.
7
Flag survives if chip reset happened because of watchdog timer overflow.
8
WDT
Watchdog timer refresh.
1: Software sets the bit to force a watchdog timer refresh.
0: Hardware resets the bit when refresh is done.
9
SWDT
Start watchdog timer.
1: Start WDT.
10
11
12
13
14
15
16
0: Stop WDT.
Watchdog Timer Data/Reload Register (WDTD)
Location
7
6
5
4
3
2
1
0
Reset Value
086h
Watchdog Timer Data/Reload
00000000b
Symbol
WDTD
Function
Initial/Reload value in Watchdog Timer.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
17
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 3D: TIMER/COUNTERS SFRS
TMOD Timer/Counter
Mode Control
89h
Timer 1
M1
Timer 0
C/T#
00h
00h
GATE
TF1
C/T#
TR1
M0
GATE
IE1
M1
IE0
M0
IT0
TCON* Timer/Counter
Control
88h
TF0
TR0
IT1
TH0
TL0
TH1
TL1
Timer 0 MSB
Timer 0 LSB
Timer 1 MSB
Timer 1 LSB
8Ch
8Ah
8Dh
8Bh
C8h
TH0[7:0]
TL0[7:0]
TH1[7:0]
TL1[7:0]
00h
00h
00h
00h
T2CON* Timer / Counter 2
Control
TF2
EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# 00h
TH2
TL2
Timer 2 MSB
Timer 2 LSB
CDh
CCh
CBh
CAh
TH2[7:0]
TL2[7:0]
00h
00h
RCAP2H Timer 2 Capture MSB
RCAP2L Timer 2 Capture LSB
* = Bit Addressable SFRs
RCAP2H[7:0]
RCAP2L[7:0]
00h
00h
344 PGM T3D.0
TABLE 3E: INTERFACE SFRS
SBUF
Serial Data Buffer
99h
98h
80h
90h
A0h
B0h
SBUF[7:0]
Indeterminate
00h
SCON* Serial Port Control
SM0
-
SM1
-
SM2
-
REN
P0[7:0]
-
TB8
-
RB8
T1
R1
T2
P0*
P1*
P2*
P3*
Port 0
Port 1
Port 2
Port 3
FFh
T2 EX
FFh
P2[7:0]
T0
FFh
RD#
WR#
T1
INT1# INT0# TXD0 RXD0
FFh
344 PGM T3E.3
* = Bit Addressable SFRs
enteredbyforcingPSEN#fromalogichightoalogiclow
while RST input is being held continuously high. The
SST89C54/58 will stay in External Host Mode as long as
RST = 1 and PSEN# = 0.
FLASH MEMORY PROGRAMMING
The SST89C54/58 internal flash memory can be pro-
grammed or erased using the following two methods:
•
•
External Host Mode (parallel only)
In-Application Programming (IAP) Mode
(parallel or serial)
A READ-ID operation is necessary to “arm” the device,
no other External Host Mode command can be enabled
untilaREAD-IDisperformed.InExternalHostMode,the
internal Flash memory blocks are accessed through the
re-assigned I/O port pins (see Figure 9 for details) by an
external host, such as an MCU programmer, PCB tester
or a PC controlled development board.
EXTERNAL HOST PROGRAMMING MODE
ExternalHostProgrammingModeprovidestheuserwith
direct Flash memory access to program the Flash
memory without using the CPU. External Host Mode is
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
18
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
The insertion of an “arming” command prior to entering
the External Host Mode by utilizing the “READ-ID” op-
eration provides additional protection for inadvertent
writes to the internal flash memory caused by a noisy or
unstablesystemenvironmentduringpower-uporbrown-
out conditions.
When the chip is in the External Host Mode, Port 0 pins
areassignedtobetheparalleldatainputandoutputpins.
Port 1 pins are assigned to be the non-multiplexed low
order address bus signals for the internal flash memory
(A7-A0). The first six bits of Port 2 pins (P2[5:0]) are
assignedtobethenon-multiplexedupperorderaddress
bussignalsfortheinternalflashmemory(A13-A8)along
with two of the Port 3 pins (P3[5] as A15 and P3[4] as
A14). Two upper order Port 2 pins (P2[7] and P2[6]) and
two upper order Port 3 pins (P3[7] and P3[6]) along with
RST, PSEN#, PROG#/ALE, EA# pins are assigned as
the control signal pins. The Port 3 pin (P3[3]) is assigned
tobetheready/busystatussignal, whichcanbeusedfor
handshaking with the external host during a flash
memory programming operation. The flash memory
programming operation (Erase, Program, Verify, etc.) is
internally self-timed.
1
2
The External Host Mode uses twelve (12) hardware
commands, which are decoded from the control signal
pins, to facilitate the internal flash memory erase, pro-
gram and verify processes. The External Host Mode is
enabledonthefallingedgeofPSEN#.TheExternalHost
ModeCommandsareenabledonthefallingedgeofALE/
PROG#. The list in Table 4 outlines all the commands
and the respective control signal assignment.
3
4
5
6
7
TABLE 4: EXTERNAL HOST MODE COMMANDS
Operation
RST
PSEN# PROG# EA# P3[7] P3[6] P2[7] P2[6] P0[7:0] P1[7:0] P3[5:4]
/ALE
P2[5:0]
8
READ-ID
H
H
H
H
H
H
H
L
L
L
L
L
L
L
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
H
H
H
L
DO
X
AL
X
AH
CHIP-ERASE
X
9
BLOCK-ERASE
SECTOR-ERASE
BYTE-PROGRAM
BURST-PROGRAM
H
H
H
L
H
L
L
X
X
A[15:12]
AH
H
H
H
L
X
AL
AL
AL
AL
10
11
12
13
14
15
16
H
H
H
DI
DI
DO
AH
L
AH
BYTE-VERIFY
(Read)
H
H
L
AH
PROG-SB1
PROG-SB2
PROG-SB3
PROG-RB0
PROG-RB1
H
H
H
H
H
L
L
L
L
L
H
H
H
H
H
H
L
H
L
H
H
L
H
H
H
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
L
H
L
H
H
L
L
L
H
X
344 PGM T4.4
Note: Symbol signifies a negative pulse and the command is asserted during the low state of PROG#/ALE input. All other
combinations of the above input pins are invalid and may result in unexpected behaviors.
Note: L = Logic low level; H = Logic high level; X = Don‘t care; AL = Address low order byte; AH = Address high order byte;
DI = Data Input; DO = Data Output; A[15:12] = 0xxxb for Block 0 and A[15:12} = “Fh” for Block 1.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
19
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
VSS VDD RST
Port 0
Input/
Output
Data
0
XTAL1
XTAL2
6
7
Bus
0
1
0
2
3
4
5
Address Bus
A13-A8
1
2
3
4
Port 2
Port 3
Busy/Ready
A14
Address Bus
A15
A15-A14
6
7
0
Flash
Control Signals
5
6
Flash
Control Signals
7
Address Bus
A7-A0
Port 1
6
7
EA# ALE / PSEN#
PROG#
344 ILL F01.1
FIGURE 9: I/O PIN ASSIGNMENTS FOR EXTERNAL HOST MODE
Product Identification
programmed must be in the erased state prior to
programming. Selection of the Erase command to use,
priortoprogrammingthedevice, willbedependentupon
the contents already in the array and the desired field
size to be programmed.
The READ-ID command accesses the Signature Bytes
that identifies the device as an SST89C54/58 and the
manufacturer as SST. External programmers primarily
use these Signature Bytes, shown in Table 5, in the
selectionofprogrammingalgorithms.TheRead-IDcom-
mand is selected by the byte code of 00h on
P2[7:6]andP3[7:6].SeeFigure10fortimingwaveforms.
The CHIP-ERASE command erases all bytes in both
memory blocks (Block 0 and Block 1) of the SST89C54/
58. This command ignores the Security Lock status and
will erase the Security bits and the Re-Map bits. The
CHIP-ERASE command is selected by the binary code
of 00b on P3[7:6] and 01b on P2[7:6]. See Figure 11 for
timing waveforms.
TABLE 5: SIGNATURE BYTES TABLE
Address
30h
Data
BFh
E4h
Manufacturer’s Code
SST89C54 Device Code
SST89C58 Device Code
31h
TheBLOCK-ERASEcommanderasesallbytesinoneof
the memory blocks (16/32K or 4K) of the SST89C54/58.
This command will not be enabled if the security lock is
enabled on the selected memory block. The selection of
thememoryblocktobeerasedisdeterminedbyA[15:12]
(P3[5], P3[4], P2[5], P1[4]). If A15 is a “0”, then the
primary flash memory Block 0 (16/32K), is selected. If
A[15:12] = “Fh”, then the secondary flash memory Block
1 (4K) is selected. The BLOCK-ERASE command is
selectedbythebinarycodeof11bonP3[7:6]and01bon
P2[7:6]. See Figure 12 for the timing waveforms.
31h
E2h
344 GPM T5.1
External Host Mode Commands
The twelve SST89C54/58 External Host Mode Com-
mands are READ-ID, CHIP-ERASE, BLOCK-ERASE
SECTOR-ERASE, BYTE-PROGRAM, BURST-PRO-
GRAM, BYTE-VERIFY, PROG-SB1, PROG-SB2,
PROG-SB3, PROG-RB0 and PROG-RB1. See Table 4
for all signal logic assignments and Table 7 for all timing
parameter values for the External Host Mode Com-
mands. The critical timing for all Erase and Program
commands, is self-generated by the on-chip flash
memory controller. The high-to-low transition of the
PROG# signal initiates the Erase and Program com-
mands, which are synchronized internally. The Read
commandsareasynchronousreads, independentofthe
PROG# signal level.
The SECTOR-ERASE command erases all of the bytes
in a sector. The sector size for the primary flash memory
(Addresses 0000h-3FFFh/7FFFh) is 128 Bytes. The
sector size for the secondary flash memory (Addresses
F000h-FFFFh) is 64 bytes. This command will not be
executed if the Security lock is enabled on the selected
memory block. The selection of the memory sector to be
erasedisdeterminedbyP1[7:6](A7&A6),P2[5:0](A13-
A8) and P3[5:4] (A15 & A14). The SECTOR-ERASE
command is selected by the binary code of 10b on
P3[7:6] and 11b on P2[7:6]. See Figure 13 for timing
waveforms.
Thefollowingthreecommandsareusedforerasingallor
partofthememoryarray.Allthedatainthememoryarray
will be erased to FFh. Memory locations that are to be
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
20
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
The BYTE-PROGRAM and BURST-PROGRAM com-
mands are used for programming new data into the
memory array. Selection of which Program command to
use will be dependent upon the desired programming
fieldsize. Programmingwillnottakeplaceifanysecurity
locks are enabled on the selected memory block.
be turned on as the SST89C54/58 enters External Host
Mode;i.e.whenPSEN#goeslowwhileRSTishigh.The
oscillator provides both clocking for the Flash Control
Unit as well as timing references for Program and Erase
operations. DuringExternalHostMode, theCPUcoreis
held in reset. Upon exit from External Host Mode, the
internal oscillator is turned off.
1
2
The BYTE-PROGRAM command programs data into a
single byte. Ports P0[7:0] are used for data in. The
memory location is selected by P1[7:0], P2[5:0], and
P3[5:4] (A15-A0). The BYTE-PROGRAM command is
selectedbythebinarycodeof11bonP3[7:6]and10bon
P2[7:6]. See Figure 14 for timing waveforms.
The same oscillator also provides the time base for the
watchdog timer and timing references for IAP Mode
Program and Erase operations. See more detailed de-
scription in later sections.
3
4
Arming Command
TheBURST-PROGRAMcommandprogramsdatatoan
entire row, sequentially byte-by-byte. Ports P0[7:0] are
used for data in. The memory location is selected
by P1[7:0], P2[5:0], and P3[5:4] (A15-A0). The BURST-
PROGRAM command is selected by the binary code of
01b on P3[7:6] and 10b on P2[7:6]. See Figure 15 for
timing waveforms.
An arming command sequence must take place before
any External Host Mode sequence command is recog-
nized by the SST89C54/58. This prevents accidental
triggering of External Host Mode Commands due to
noise or programmer error. The arming command is as
follows:
5
6
1. PSEN# goes low while RST is high. This will get
the machine in External Host Mode, re-configur-
ing the pins.
The BYTE-VERIFY command allows the user to verify
that the SST89C54/58 correctly performed an Erase or
Program command. Ports P0[7:0] are used for data out.
ThememorylocationisselectedbyP1[7:0],P2[5:0],and
P3[5:4] (A15-A0). The BYTE-VERIFY command is se-
lected by the binary code of 11b on P3[7:6] and 00b on
P2[7:6]. This command will be disabled if any security
locks are enabled on the selected memory block. See
Figure 16 for timing waveforms.
7
2. A Read-ID command is issued and held for 1 ms.
After the above sequence, all other External Host Mode
commands are enabled. Before the Read-ID command
is received, all other External Host commands received
are ignored.
8
9
Programming a SST89C54/58
To program data into the memory array, apply power
supply voltage (VDD) to VDD and RST pins, and perform
the following steps:
The PROG-SB1, PROG-SB2, PROG-SB3 commands
program the security bits, the functions of these bits are
described in a Security Lock section and also in Table 8.
Once programmed, these bits can only be cleared
through a CHIP-ERASE command.
10
11
12
13
14
15
16
1. Maintain RST high and toggle PSEN# from logic
high to low, in sequence per the appropriate timing
diagram.
The PROG-RB1, and PROG-RB0 commands program
the Re-Map[1:0] bits. The Re-Map[1:0] bits determine
the Memory Re-mapping default option on reset. Upon
completion of the Reset sequence, the MAP_EN[1:0]
bits are initialized to the default value set by the Re-
Map[1:0]bitsaccordingtoTable2.Subsequentprogram
manipulation of MAP_EN[1:0] bits will alter the Memory
Re-mapping option but will not change the Re-Map[1:0]
bits. Therefore, any changes to MAP_EN[1:0], without
correspondingupdatestoRe-Map[1:0],willnotsurvivea
Reset cycle.
2. Raise EA# High (either VIH or VH).
3. Issue READ-ID command to enable the External
Host Mode.
4. Verify that the memory blocks or sectors for pro-
grammingisintheerasedstate, FFh. Iftheyarenot
erased, then erase them using the appropriate
Erase command.
5. Select the memory location using the address lines
(P1[7:0], P2[5:0], P3[5:4]).
6. Present the data in on P0[7:0].
7. Pulse ALE/PROG#, observing minimum pulse
width.
If an External Host Mode command, except for CHIP-
ERASE, is issued to a locked memory block, the device
will ignore this command.
8. Wait for low to high transition on READY/BUSY#
(P3[3]).
External Host Mode Clock Source
In External Host Mode, an internal oscillator will provide
clockingfortheSST89C54/58.Theon-chiposcillatorwill
9. Repeat steps 5 – 8 until programming is finished.
10. Verify the flash memory contents.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
21
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Data# Polling (P0[7] & P0[3]
Flash Operation Status Detection (Ext. Host
Handshake)
During a Program operation, any attempts to read (Byte-
Verify), while the device is busy, will receive the comple-
ment of the data of the last byte loaded (logic low, i.e. “0”
for an erase) on P0[3] and P0[7] with the rest of the bits
“0”. During a Program operation, the Byte-Verify com-
mand is reading the data of the last byte loaded, not the
data at the address specified.
The SST89C54/58 provide two firmware means for an
external host to detect the completion of a flash memory
operation to optimize the Program or Erase time. The
end of a flash memory operation cycle (Erase or Pro-
gram) can be detected by: 1) monitoring the Ready/
Busy# bit at P3[3]; 2) monitoring the Data# Polling bit at
P0[7] and P0[3].
The true data will be read from P0[7], when the device
completes each byte programmed among the burst to
indicate the Ready status to receive the next byte. When
the external host detects the Ready status after a byte
among the burst is programmed, it should then put the
data/address (in the same page) of the next byte on the
bus and drive ALE/PROG# low immediately, before the
time-out limit expires (See programming time spec. in
Table7fordetails.).ThetruedatawillbereadfromP0[3],
whentheBurst-Programcommandisterminatedandthe
device is ready for the next operation.
Ready/Busy# (P3[3])
The progress of the flash memory programming can be
monitored by the Ready/Busy# output signal. P3[3] is
drivenlow,sometimeafterALE/PROG#goeslowduring
a flash memory operation to indicate the Busy# status of
the Flash Control Unit (FCU). P3[3] is driven high when
the Flash programming operation is completed to indi-
cate the Ready status.
During a Burst-Program operation, P3[3] is driven high
(Ready) in between each byte-programmed among the
bursttoindicatethereadystatustoreceivethenextbyte.
When the external host detects the Ready status after a
byteamongtheburstisprogrammed,itshallthenputthe
data/address (within the same page) of the next byte on
the bus and drive ALE/PROG# low (pulse), before the
time-out limit expires. See Table 7 for details. Burst-
Program command presented after time-out will wait
until next cycle. Therefore, it will have longer program-
ming time.
The termination of the Burst-Program can be accom-
plished by: 1) Change to a new X-Addresses (Note: the
X-Address range are different for the 4Kx8 flash Block 1
andforthe16/32Kx8flashBlock0.);2)Changetoanew
commandthatrequiresahightolowtransitionoftheALE/
PROG# (i.e. any Erase or Program command); 3) Wait
for time out limit expires (20 µs); when programming the
next byte.
Flash Memory Programming with External Host Mode (Figures 10-16)
T
SU
RST
PSEN#
T
ES
ALE/PROG#
EA#
T
T
RD
RD
P2[7:6] ,P3[7:6]
P3[5:4] ,P2[5:0] ,P1
P0
0000b
0030h
BFh
0000b
0031h
E4h/E2h
344 ILL F02.5
FIGURE 10: READ-ID
Read chip signature and identification registers at the addressed location.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
22
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
T
1
SU
RST
T
ES
2
PSEN#
T
ADS
3
ALE/PROG#
T
DH
T
PROG
4
EA#
T
CE
P3[3]
5
P3[7:6], P2[7:6]
0001b
6
344 ILL F03.4
7
FIGURE 11: CHIP-ERASE
Erase both flash memory blocks. Security lock is ignored and the security bits are erased too.
8
9
T
SU
RST
10
11
12
13
14
15
16
T
ES
PSEN#
T
ADS
ALE/PROG#
T
T
DH
PROG
EA#
T
BE
P3[3]
P3[7:6], P2[7:6]
P3[5:4], P2[5:0]
1101b
AH
344 ILL F04.5
FIGURE 12: BLOCK-ERASE
Erase one of the flash memory blocks, if the security lock is not activated on that flash memory block. The highest
address bits A[15:12] determines which block is erased. For example, if A15 is “0”, primary flash memory block
is erased. If A[15:12] = “Fh”, the secondary block is erased.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
23
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
T
SU
RST
T
ES
PSEN#
T
ADS
ALE/PROG#
T
T
DH
PROG
EA#
P3[3]
T
SE
P3[7:6], P2[7:6]
P3[5:4], P2[5:0]
1011b
AH
P1
AL
344 ILL F05.4
FIGURE 13: SECTOR-ERASE
Erase the addressed sector if the security lock is not activated on that flash memory block.
T
SU
RST
T
ES
PSEN#
T
ADS
ALE/PROG#
T
T
DH
PROG
EA#
P3[3]
T
PB
P3[5:4], P2[5:0]
P1
AH
AL
P0
DI
P3[7:6], P2[7:6]
1110b*
344 ILL F06.6
* See Table 4 for control signal assignments for PROG-SBx and PROG-RBx.
FIGURE 14: BYTE-PROGRAM; PROG-SB3, PROG-SB2, PROG-SB1, PROG-RB1 AND PROG-RB0
Programtheaddressedcodebyteifthebytelocationhasbeensuccessfullyerasedandnotyetprogrammed. Byte-
Program operation is only allowed when the security lock is not activated on that flash memory block.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
24
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
T
SU
RST
1
T
ES
PSEN#
2
T
ADS
ALE/PROG#
T
T
DH
T
T
DH
DH
PROG
3
EA#
P3[3]
4
T
T
BUPRCV
T
T
BUP
BUP1
BUP
row address
byte address
row address
byte address
row address
5
byte address
DI
byte address
DI
P0
DI
6
P3[7:6], P2[7:6]
0110b
344 ILL F07.4
16K/32K Block
4K Block
row address = A15: A6; byte address = A5:A0
row address = A15: A5; byte address = A4:A0
7
FIGURE 15: BURST-PROGRAM
Program the entire addressed row by burst programming each byte sequentially within the row if the byte location
has been successfully erased and not yet programmed. This operation is only allowed when the security lock is
not activated on that flash memory block.
8
9
T
SU
RST
10
11
12
13
14
15
16
T
ES
PSEN#
ALE/PROG#
EA#
T
OA
1100b
P3[7:6], P2[7:6]
P0
T
AHA
DO
T
ALA
AL
P1
AH
P3[5:4], P2[5:0]
344 ILL F08.3
FIGURE 16: BYTE-VERIFY
Read the code byte from the addressed flash memory location if the security lock is not activated on that flash
memory block.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
25
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
IN-APPLICATION PROGRAMMING MODE
The two Program commands are for programming new
data into the memory array. The portion of the memory
array to be programmed should be in the erased state,
FFh. If the memory is not erased, then erase it with an
appropriate Erase command. Warning: Do not write
(program or erase) to a block that the code is cur-
rently fetching from. This will cause unpredictable
program behavior and may corrupt program data.
The SST89C54/58 offers 20/36 KByte of In-Application
Programmableflashmemory.DuringIn-ApplicationPro-
gramming, the CPU of the microcontroller enters IAP
Mode. The two blocks of flash memory allows the CPU
to concurrently execute user code from one block, while
the other is being reprogrammed. The CPU may also
fetch code from an external memory while all internal
flash is being reprogrammed. The chip can start the In-
ApplicationProgrammingoperationeitherwiththeexter-
nal program code execution being enabled (EA# = L) or
disabled(EA#=H).Themailboxregisters(SFST,SFCM,
SFAL, SFAH, SFDT and SFCF) located in the Special
Function Register (SFR), control and monitor the
device’s erase and program process.
The CHIP-ERASE command erases all bytes in both
memoryblocks(16/32Kand4K).Thiscommandignores
the Security Lock status and will erase the security lock
bits and Re-Map bits. The CHIP-ERASE command
sequence is as follows:
IAP Enable
ORL SFCF, #40h
Table 6 outlines the commands and their associated
settings of the mailbox registers.
In-Application Programming Mode Clock Source
During IAP Mode, both the CPU core and the flash
controllerunitaredrivenofftheexternalclock. However,
an internal oscillator will provide timing references for
ProgramandEraseoperations.ThedurationofProgram
and Erase operations will be identical between External
Host Mode and In-Application Mode. The internal oscil-
latorisonlyturnedonwhenrequired, andisturnedoffas
soon as the Flash operations complete.
Set-Up
MOV SFDT, #55h
Polling scheme
MOV SFCM, #01h
Interrupt scheme
MOV SFCM, #81h
SFST[2] indicates
INT1# occurrence
operation completion
indicates completion
IAP Enable Bit
The IAP Enable Bit, SFCF[6], initializes In-Application
Programming mode, enabling IAP command decoding.
Until this bit is set all flash programming IAP commands
will be ignored.
344 ILL F39.2
TheBLOCK-ERASEcommanderasesallbytesinoneof
the two memory blocks (16/32K or 4K). The selection of
the memory block to be erased is determined by the
“A15”bit(SFAH[7])oftheSuperFlashAddressRegister.
If SFAH[7] = 0b, the primary flash memory Block 0 is
selected (16/32K). If SFAH[7:4] = Fh, the secondary
flash memory Block 1 is selected (4K). The BLOCK-
ERASE command sequence is as follows:
In-Application Programming Mode Commands
All of the following commands can only be initiated in the
IAP Mode. In all situations, writing the control byte to the
(SFCM) register will initiate all of the operations. All
commands (except CHIP-ERASE) will not be enabled if
the security features are enabled on the selected
memory block. The critical timing for all Erase and
Program commands, is self-generated by the on-chip
flash controller unit.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
26
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
The 16/32 KByte memory contains 128/256 uniform
sectorsof128Byteseach.The4KBytememorycontains
64uniformsectorsof64Byteseach. Theselectionofthe
sector to be erased is determined by the contents of
SFAH, SFAL. Please refer to Figure 4 for an illustration
of memory sector organization.
IAP Enable
1
Erase 32 KBlock
MOV SFAH, #00h
Erase 4 KBlock
MOV SFAH, #F0h
2
OR
The BYTE-PROGRAM command programs data into a
singlebyte. TheBYTE-PROGRAMcommandsequence
is as follows:
3
Set-Up
MOV SFDT, #55h
4
IAP Enable
Polling scheme
Interrupt scheme
5
MOV SFCM, #0Dh
MOV SFCM, #8Dh
Program byte address
MOV SFAH, #byte_addressh
MOV SFAL, #byte_addressl
6
SFST[2] indicates
operation completion
INT1# occurrence
indicates completion
344 ILL F40.5
Move data to SFDT
MOV SFDT, #data
7
The SECTOR-ERASE command erases all of the bytes
in a sector. The sector size for the primary flash memory
Block 0 (Addresses 0000h-3FFFh/7FFFh) is 128 Bytes.
The sector size for the secondary flash memory Block 1
(Address F000h-FFFFh) is 64 Bytes. The SECTOR-
ERASE command sequence is as follows:
8
Polling scheme
MOV SFCM, #0Eh
Interrupt scheme
MOV SFCM, #8Eh
9
SFST[2] indicates
operation completion
INT1# occurrence
indicates completion
10
11
12
13
14
15
16
344 ILL F42.3
IAP Enable
Program sector address
MOV SFAH, #sector_addressh
MOV SFAL, #sector_addressl
The BURST-PROGRAM command programs data into
half of a sector (row) which has the same row address,
sequentially byte-by-byte. Refer to the Memory Organi-
zation section and Figures 4 and 15 for details. The
MOVCcommandandallIAPcommandsexceptBURST-
PROGRAM are invalid during the BURST-PROGRAM
cycle. The BURST-PROGRAM command sequence is
as follows:
Polling scheme
MOV SFCM, #0Bh
Interrupt scheme
MOV SFCM, #8Bh
SFST[2] indicates
INT1# occurrence
operation completion
indicates completion
344 ILL F41.3
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
27
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
PROG-SB3, PROG-SB2, PROG-SB1 commands are
used to program the Security bits (see Table 8). These
commands work similarly to a BYTE-PROGRAM com-
mand, except no address and data is specified. Upon
completion of any of those commands, the security
options will be updated immediately.
IAP Enable
Program byte address
MOV SFAH, #byte_addressh
MOV SFAL, #byte_addressl
Security bits previously in un-programmed state can be
programmed by these commands. The PROG-SB3,
PROG-SB2, PROG-SB1 sequences are as follows:
Move data to SFDT
MOV SFDT, #data
IAP Enable
Polling scheme
MOV SFCM, #06h
Interrupt scheme
MOV SFCM, #86h
Set-Up
MOV SFDT, #55h
Next same
row address
SFST[3] indicates
byte completion
INT1# occurrence
indicates completion
Program sb1
MOV SFCM, #0Fh
or
Program sb2
MOV SFCM, #03h
or
Program sb3
MOV SFCM, #05h
or
OR
OR
MOV SFCM, #8Fh
MOV SFCM, #83h
MOV SFCM, #85h
Program
another
byte
Y
Polling SFST[2]
indicates completion
Interrupt INT1#
occurrence completion
N
SFST[2] indicates
344 ILL F45.3
Burst-Program completion
344 ILL F43.5
PROG-RB1, PROG-RB0 commands are used to pro-
gram the Re-Map[1:0] bits (see Table 2). These com-
mands work similarly to a BYTE-PROGRAM command
except no address and data is needed. These com-
mands only change the Re-Map[1:0] bits and have no
effect on MAP_EN[1:0] until after a reset cycle. There-
fore, the effect of these commands is not immediate.
The BYTE-VERIFY command allows the user to verify
thattheSST89C54/58hascorrectlyperformedanErase
or Program command. The BYTE-VERIFY command
sequence is as follows:
IAP Enable
Program byte address
MOV SFAH, #byte_addressh
MOV SFAL, #byte_addressl
MOV SFCM, #0Ch
SFDT register
contains data
344 ILL F44.2
BYTE-VERIFY command returns the data byte in SFDT
if the command is successful. The user is required to
check that the previous Flash operation has fully com-
pleted before issuing a BYTE-VERIFY.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
28
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Re-Map bits previously in un-programmed state can be
programmed by these commands. The PROG-RB1,
PROG-RB0 sequences are as follows:
Polling
A command that uses the polling method to detect flash
operation completion should poll on the Flash_Busy bit
(SFST[2]). When Flash_Busy de-asserts (logic 0), the
device is ready for the next operation.
1
2
The BUSY bit (SFST[3]) is provided for Burst-Program.
In between bytes within a burst sequence, the Busy bit
will become logic 0 to indicate that the next Burst-
Programbyteshouldbepresented.Completionofthefull
burstcycleisindicatedalsobyFlash_Busybit(SFST[2]).
IAP Enable
Set-Up
MOV SFDT, #55h
3
MOVCinstructionmayalsobeusedforverificationofthe
Programming and Erase operation of the flash memory.
MOVC command will fail if it is directed at a flash block
that is still busy.
4
Program Re-Map [0]
MOV SFCM, #08h
or
Program Re-Map [1]
MOV SFCM, #09h
or
5
MOV SFCM, #88h
MOV SFCM, #89h
6
Polling SFST[2]
indicates completion
Interrupt INT1#
occurrence completion
OR
7
344 ILL F46.4
8
9
10
11
12
13
14
15
16
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
29
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Interrupt Termination
For an interrupt to occur, appropriate interrupt enable
bits must be set. EX1 and EA bits of IE register must be
set.TheTCON[2](IT1)bitofTCONregistermustalsobe
set for edge trigger detection.
Ifinterruptterminationisselected,(SFCM[7]isset),then
an interrupt (INT1) will be generated to indicate flash
operation completion. Under this condition, the INT1
becomesaninternalinterruptsource.TheINT1#pincan
nowbeusedasageneralpurposeportpin, anditcannot
be a source of External Interrupt 1.
TABLE 6: IN-APPLICATION PROGRAMMING MODE COMMANDS
Operation
SFAH [7:0]
SFAL [7:0]
SFDT [7:0]
SFCM [6:0]1
01h
CHIP-ERASE
X
X
55h
55h
X
BLOCK-ERASE
SECTOR-ERASE
BYTE-PROGRAM
BURST-PROGRAM
BYTE-VERIFY (Read)
AH2
AH
AH
AH
AH
X
0Dh
AL
AL
AL
AL
0Bh
DI
0Eh
DI
06h
DO
0Ch
344 PGM T6.3
Notes: X = Don’t Care; AL = Address low order byte; AH = Address high order byte;
DI = Data Input; DO = Data Output
All other values are in hex
1
Interrupt/Polling enable for flash operation completion
SFCM[7] = 1: Interrupt enable for flash operation completion
0: polling enable for flash operation completion
SFAH[7] = 0: Selects Block 0: SFAH[7:4] = Fh selects Block 1
2
TABLE 7: FLASH MEMORY PROGRAMMING/VERIFICATION PARAMETERS
Parameter1,2
Reset Setup Time
Symbol
TSU
Min
3
1
Max
Units
µs
Read-ID Command Width
PSEN# Setup Time
TRD
TES
µs
1.125
0
µs
Address, Command, Data Setup Time
Chip-Erase Time
TADS
TCE
ns
11.7
9.4
ms
ms
ms
µs
Block-Erase Time
TBE
Sector-Erase Time
TSE
1.1
1.2
0
2.3
Program Setup Time
TPROG
TDH
Address, Command, Data Hold
Byte-Program Time 3
ns
TPB
110
50
µs
Verify Command Delay Time
Verify High Order Address Delay Time
Verify Low Order Address Delay Time
First Burst-Program Byte Time4
Burst-Program Time 3,4
Burst-Program Recovery4
Burst-Program Time-Out Limit
TOA
ns
TAHA
TALA
TBUP1
TBUP
TBUPRCV
TBUPTO
50
ns
50
ns
85
µs
31
20
45
µs
110
µs
µs
344 PGM T7.4
Note:
1. Program and Erase times will scale inversely relative to programming clock frequency.
2. All timing measurements are from the 50% of the input to 50% of the output.
3. Each byte must be erased before program.
4. External Host Mode only.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
30
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Accessing Internal Memory (EA# = 0)
Accessing External Memory (EA# = 1)
VSS VDD RST
VSS VDD RST
1
Address
and
Data
Bus
General
Purpose
I/O
0
0
XTAL1
XTAL2
XTAL1
XTAL2
Port 0
Port 0
6
7
6
7
2
0
1
0
1
T2
T2EX
T2
T2EX
RXD
RXD
0
0
TXD
2
3
4
5
TXD
2
3
4
5
1
2
3
4
1
2
3
4
INT0#
INT0#
Port 1
Port 3
Port 1
3
INT1#
T0
INT1#
T0
Port 3
6
7
6
7
T1
T1
5
6
5
6
4
WR#
WR#
0
0
RD#
RD#
7
7
General
Purpose
I/O
Address
Bus
Port 2
Port 2
6
7
6
7
5
EA# ALE / PSEN#
PROG#
EA# ALE / PSEN#
PROG#
344 ILL F09.1
6
FIGURE 17: IN-APPLICATION PROGRAMMING MODE I/O ASSIGNMENT
7
TIMERS/COUNTERS
SERIAL I/O (UART)
The SST89C54/58 have three 16-bit registers that can
be used as either timers or event counters. The three
Timers/Counters are the Timer 0 (T0), Timer 1 (T1), and
Timer 2 (T2) registers. These three registers are located
in the SFR as pairs of 8-bit registers. The low byte of the
T0 register is stored in the Timer 0 LSB (TL0) special
function register and the high byte of the T0 register is
stored in the Timer 0 MSB (TH0) special function regis-
ter. The low byte of the T1 register is stored in the Timer
LSB (Tl1) special function register and the high byte of
theT1registerisstoredintheTimer1MSB(TH1)special
functionregister. ThelowbyteoftheT2registerisstored
intheTimer2LSB(TL2)specialfunctionregisterandthe
high byte of the T2 register is stored in the Timer 2 MSB
(TH2) special function register.
The SST89C54/58 Serial I/O ports is a full duplex port
that allows data to be transmitted and received simulta-
neously in hardware by the transmit and receive regis-
ters, respectively, while the software is performing other
tasks. The Serial I/O port performs the function of an
UART (Universal Asynchronous Receiver/Transmitter)
chip. Thetransmitandreceiveregistersarebothlocated
intheSerialDataBuffer(SBUFspecialfunctionregister.
Writing to the SBUF register loads the transmit register,
andreadingfromtheSBUFregisterobtainsthecontents
of the receive registers.
8
9
10
11
12
13
14
15
16
TheSerialI/Oporthasfourmodesofoperationwhichare
selected by the Serial Port Mode Specifier (SM0 and
SM1) bits of the Serial Port Control (SCON) special
function register. In all four modes, transmission is initi-
ated by any instruction that uses the SBUF register as a
destination register. Reception is initiated in mode 0
when the Receive Interrupt (RI) flag bit of the Serial Port
Control (SCON) special function register is cleared and
the Reception Enable/ Disable (REN) bit of the SCON
register is set. Reception is initiated in the other modes
by the incoming start bit if the REN bit of the SCON
register is set.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
31
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
WATCHDOG TIMER
TheWDTintheSST89C54/58sharethesametimebase
with the flash controller unit. When the flash controller
unit is operating, the time base will be re-started by the
hardware periodically, therefore delaying the time-out
periodofthewatchdogtimer.Theupper8-bitsofthetime
baseregisterareusedasthereloadregisteroftheWDT.
The SST89C54/58 offer an enhanced programmable
Watchdog Timer (WDT) for fail safe protection against
software deadlock and allows an automatic recovery.
To protect the system against software deadlock, the
user has to refresh the WDT within a user defined time
period. If the software fails to do this periodical refresh,
an internal hardware reset will be initiated. The software
can be designed such that the WDT times out if the
program does not work properly. It also times out if a
software error is based on the hardware related prob-
lems.
The internal oscillator that drives the WDT operates
withinafrequencyrangeasshowninTable11.Minimum
clock cycle for the WDT is 7.7ms.
Figure 18 provides a block diagram of the WDT. Two
SFRs (WDTC and WDTD) control watchdog timer op-
eration. During idle mode, WDT operation is temporarily
suspended,andresumesuponaninterruptexitfromidle.
7.7 ms
min.
WDT Reset
CLK
Internal Reset
Counter
WDT Upper Byte
Ext. RST
WDTC
WDTD
344 ILL F10.2
FIGURE 18: BLOCK DIAGRAM OF PROGRAMMABLE WATCHDOG TIMER
SoftLock
SECURITY LOCK
SoftLockallowsflashcontentstobealteredunderasecure
environment. This lock option allows the user to update
programcodeintheSoftLockedmemoryblockthroughIn-
Application Programming Mode under a predetermined
secure environment. For example, if the Block 1 (4K)
memory block is locked, and the Block 0 (16K/32K)
memory block is Soft Locked, code residing in Block 1 can
program Block 0. The following IAP mode commands
issued through the command mailbox register, SFCM,
executed from a Hard Locked block can be operated on a
Soft Locked block: BLOCK-ERASE, SECTOR-ERASE,
BYTE-PROGRAM, BURST-PROGRAM and BYTE-
VERIFY.
The Security feature protects against software piracy and
prevents the contents of the flash from being read by
unauthorized parties. It also protects against code corrup-
tion resulting from accidental erasing and programming to
theinternalflashmemorylocations.Therearetwodifferent
types of security locks in the SST89C54/58 security lock
system: Hard Lock and SoftLock.
Hard Lock
When the Hard Lock is activated, the MOVC instructions
executedfromUn-LockedorSoftLockedprogramaddress
space, are disabled from reading code bytes in Hard
Locked memory blocks (See Table 9). The Hard Lock can
either lockbothflashmemoryblocksorjustlocktheupper
flash memory block (Block 1). All External Host and IAP
commands except for CHIP-ERASE are ignored for the
Hard Locked memory blocks.
In External Host Mode, SoftLock behaves the same as a
Hard Lock.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
32
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
STATUS OF THE SECURITY LOCK
available for read operation via Byte-Verify. In the third
level, three different options are available: Block 1 Hard
Lock/Block0SoftLock,SoftLockonbothblocks,andHard
Lock on both blocks. Locking both blocks is the same as
Level 2 except read operation isn’t available. The fourth
level of security is the most secure level operation. It
doesn’t allow read/write of internal memory or boot from
external memory. Please note that for unused combina-
tions of the security lock bit the chip will default to Level 4
status.
ThethreebitsthatindicatetheSST89C54/58securitylock
statusarelocatedinSFST[7:5].AsshowninFigure19and
Table 8, the three security lock bits control the lock status
oftheprimaryandsecondaryblocksofmemory.Thereare
four distinct levels of security lock status. In the first level,
none of the security lock bits are programmed and both
blocks are unlocked. In the second level, although, both
blocks are now locked and cannot be written, they are
1
2
3
4
Level 1
Level 2
UUU/NN
PUU/LL
5
6
UPU/SS
=
UUP/LS
Level 3
PPU/LL
PUP/LL
7
8
PPP/LL
Level 4
Notes:
344 ILL F38.1
1. P = Programmed (Cell logic state = 0), U = Unprogrammed (Cell logic state = 1),
N = Not Locked, L = Hard Locked, S = SoftLocked
9
FIGURE 19: SECURITY LOCK LEVELS
10
11
12
13
14
15
16
TABLE 8: SECURITY LOCK OPTIONS
Security Lock Bits
Security Status of:
Security Type
Level SFST[7:5]
11
U
P
21
31
U
Block 1
Block 0
1
2
000
100
U
Unlock
Unlock
No Security Features are Enabled.
U
U
Hard Lock Hard Lock MOVC instructions executed from external
program memory are disabled from fetching
code bytes from internal memory, EA# is
sampled and latched on Reset, and further
programming of the flash is disabled.
3
110
101
010
P
P
U
P
U
P
U
P
U
Hard Lock Hard Lock Level 2 plus Verify disabled, both blocks locked.
SoftLock SoftLock Level 2 plus verify disable. code in Block 1
can program Block 0 and vice versa.
001
111
U
P
U
P
P
P
Hard Lock SoftLock Level 2 plus verify disabled, code in Block 1
can program Block 0.
4
Hard Lock Hard Lock Same as Level 3, but external boot is
disabled.
344 PGM T8.4
Notes:
1 1, 2, and 3, respectively, refer to the first, second, and third security lock bits.
2 P = Programmed (Cell logic state = 0), U = Unprogrammed (Cell logic state = 1).
3 SFST[7:5] = Security Lock Decoding Bits (SECD)
4 All unused combinations default to level 4, “PPP”.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
33
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 9: MOVC ACCESS WITH SECURITY LOCK ACTIVATED
SFST[7:5]
011/100/101/110/111
(Hard Lock on
MOVC Address1
Target Address2
Any Location
Block 0/1
MOVC allowed3
Block 0/1
Y
N
Y
Y
N
Y
Y
N
Y
Y
N
Y
External Memory
both blocks)
External
Block 0
001
Block 0
Block 1
(Block 0 = SoftLock
Block 1 = Hard Lock)
External
Block 1
Any Location
Block 0/1
External
External
010
(SoftLock
on both blocks)
000
Block 0/1
External
Any Location
Block 0/1
External
Any Location
Any Location
Y
344 PGM T9.3
Notes:
1
2
3
Location of MOVC instruction
Target Address is the location of the instruction being read
Y = Indicates MOVC instruction is allowed; N = Indicates MOVC instruction is not allowed;
RESET
A system reset initializes the MCU and begins program
executionatprogrammemorylocation0000h. Thereset
input for the SST89C54/58 is the RST pin. In order to
reset the SST89C54/58, a logic level high must be
appliedtotheRSTpinforatleasttwomachinecycles(24
clocks), after the oscillator becomes stable. ALE,
PSEN#areweaklypulledhighduringreset.Duringreset,
ALE and PSEN# output a high level in order to perform
correct reset. This level must not be affected by external
element. A system reset will not affect the 256 Bytes of
on-chip RAM while the SST89C54/58 is running, how-
ever, the contents of the on-chip RAM during power up
are indeterminate. All Special Function Registers (SFR)
return to their reset values, which are outlined in Tables
3A to 3E.
WhenpowerisappliedtotheSST89C54/58,theRSTpin
must be held long enough for the oscillator to start up
(usually several milliseconds for a low frequency crys-
tal), in addition to two machine cycles for a valid Power-
On Reset. An example of a method to extend the RST
signalistoimplementaRCcircuitbyconnectingtheRST
pin to VDD through a 10µF capacitor and to VSS through
an 8.2K resistor as shown in Figure 20. Note that if an
RC circuit is being used, provisions should be made to
ensure the VDD rise time does not exceed 1 millisecond
and the oscillator start-up time does not exceed 10
milliseconds.
For a low frequency oscillator with slow start-up time the
reset signal must be extended in order to account for the
slowstart-uptime.Thismethodmaintainsthenecessary
relationship between VDD and RST to avoid program-
ming at an indeterminate location, which may cause
corruption in the code of the flash. For more information
on system level design techniques, please review De-
signConsiderationsfortheSSTFlashFlex51Family
Microcontroller Application Note.
Power-On Reset
At initial power up, the port pins will be in a random state
until the oscillator has started and the internal reset
algorithm has written one’s to all the pins. Powering up
thedevicewithoutavalidresetcouldcausetheCPU
to start executing instructions from an indetermi-
nate location. Such undefined states may inadvert-
ently corrupt the code in the flash.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
34
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
POWER-SAVING MODES
Power Down
The Power Down mode is also entered by a software
command which sets the PD bit in the PCON register. In
Power Down mode, the clock is stopped and external
interrupts are active for level sensitive interrupt only.
Power Down mode reduces the current dissipation to
15µA, typical.
The SST89C54/58 provides three power saving modes
of operation for applications where power consumption
iscritical.Thethreepowersavingmodesare:Idle,Power
Down and Standby (Stop Clock).
1
2
Idle
The SST89C54/58 exits Power Down mode through
either an enabled external level sensitive interrupt or a
hardware reset. The interrupt clears the PD bit and the
program resumes execution beginning at the instruction
immediately following the one which invoked the Power
Down mode. A hardware reset starts the device similar
to power-on reset.
Idle mode is entered by a software command which sets
the IDL bit in the PCON register. In Idle mode the
program counter (PC) is stopped. The system clock
continues to run and all interrupts and peripheral func-
tions (timers/counters, serial port, etc.) are active. In this
mode the power dissipation is approximately 25% of the
fully active device.
3
4
5
The SST89C54/58 exits Idle mode through either a
systeminterruptorahardwarereset.Theinterruptclears
the IDL bit and the program resumes execution begin-
ning at the instruction immediately following the one
whichinvokedtheIdlemode.Ahardwareresetstartsthe
device similar to power-on reset.
Standby (Stop Clock)
Standby mode is similar to Power Down mode, except
that Power Down mode is initiated by a software com-
mand and Standby mode is initiated by external hard-
ware gating off the external clock to the SST89C54/58
device. The current dissipation is reduced to 15µA,
typical.Theon-chipSRAMandSFRdataaremaintained
in Standby mode. The device resumes operation at the
next instruction when the clock is reapplied to the part.
6
7
8
Table 10 outlines the different power-saving modes,
including entry and exit procedures and MCU
functionality.
9
10
11
12
13
14
15
16
V
DD
+
-
10µF
8.2K
V
DD
RST
SST89C54/58
C
2
XTAL2
XTAL1
12MHz
C
1
344 ILL F31.1
FIGURE 20: POWER-ON RESET CIRCUIT
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
35
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 10: SST89C54/58 POWER SAVING MODES
Mode
Initiated by
Current Drain
State of MCU
Exited by
Enabled interrupt or
hardware reset. Start of
interrupt clears IDL bit
and exits Idle mode,
after the ISR RETI in-
struction program re-
sumes execution be-
ginning at the instruc-
tion following the one
that invoked Idle mode.
If needed in a specific
application, a user
could consider placing
two or three NOP in-
structions after the in-
struction that invokes
idle mode to eliminate
any problems. A hard-
ware reset restarts the
device similar to a
power-on reset.
Idle Mode
Software
(Set IDL bit in
PCON)
25% of IDD level when
device is fully active
CLK is running.
Interrupts, serial port
and timers/counters are
active. Program
Counter is stopped.
ALE and PSEN#
signals at a HIGH level
during Idle. All registers
remain unchanged.
Power Down Mode
Software
(Set PD bit in
PCON)
Typically 15 microamps. CLK is stopped. On-
Minimum VDD for Power chip SRAM and SFR
Enabled external level
sensitive interrupt or
hardware reset. Start of
interrupt clears PD bit
Down mode is 2.7V.
data is maintained.
ALE and PSEN#
signals at a LOW level and exits Power Down
during Power Down. mode, after the ISR
External Interrupts are RETI instruction pro-
only active for level
sensitive interrupts, if
enabled.
gram resumes execu-
tion beginning at the in-
struction following the
one that invoked Power
Down mode. If needed
in a specific applica-
tion, a user could con-
sider placing two or
three NOP instructions
after the instruction that
invokes Power Down
mode to eliminate any
problems. A hardware
reset restarts the de-
vice similar to a power-
on reset.
Standby (Stop Clock) External hardware
Mode
Typically 15 microamps. CLK is frozen. On-chip
SRAM and SFR data is
Gate ON external
clock. Program
gates OFF the external Minimum VDD for
clock input to the MCU. Standby mode is 2.7V. maintained. ALE and
execution resumes at
the instruction
following the one
during which the clock
was gated off.
This gating should be
synchronized with an
input clock transition
(low-to-high or high-to-
low).
PSEN# are maintained
at the levels prior to the
clock being frozen.
344 PGM T10.3
344-2 8/00
© 2000 Silicon Storage Technology, Inc.
36
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
CLOCK INPUT OPTIONS
Recommended Capacitor Values for Crystal
Oscillator
ShowninFigure21aretheinputandoutputofaninternal
invertingamplifier(XTAL1,XTAL2),whichcanbeconfig-
ured for use as an on-chip oscillator.
Crystal manufacturer, supply voltage, and other factors
may cause circuit performance to differ from one applica-
tion to another. C1 and C2 should be adjusted appropri-
ately for each design. The table below, shows the typical
values for C1 and C2 at a given frequency. If, following the
satisfactoryselectionofallexternalcomponents,thecircuit
is still over driven, a series resistor, Rs, may be added.
1
When driving the device from an external clock source,
XTAL2 should be left disconnected and XTAL1 should
be driven.
2
3
At start-up, the external oscillator may encounter a
higher capacitive load at XTAL1 due to interaction be-
tween the amplifier and its feedback capacitance. How-
ever, the capacitance will not exceed 15pF once the
external signal meets the VIL and VIH specifications.
RECOMMENDED VALUES FOR CRYSTAL OSCILLATOR
Frequency
< 8MHz
C1 and C2
90-110pF
18-22pF
Rs (Optional)
4
100
200
200
8-12MHz
>12MHz
5
18-22pF
More specific information on On-Chip oscillator design
canbefoundinFlashFlex51OscillatorCircuitDesign
Considerations Application Note.
6
7
8
R
S
XTAL2
9
C
C
NC
XTAL2
XTAL1
2
EXTERNAL
OSCILLATOR
SIGNAL
1
10
11
12
13
14
15
16
XTAL1
Vss
Vss
344 ILL F12.1
External Clock Drive
Using the On-Chip Oscillator
FIGURE 21: OSCILLATOR CHARACTERISTICS
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
37
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
ELECTRICAL SPECIFICATION
Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress
Ratings”maycausepermanentdamagetothedevice. Thisisastressratingonlyandfunctionaloperationofthedevice
at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied.
Exposure to absolute maximum stress rating conditions may affect device reliability.)
Ambient Temperature Under Bias ................................................................................................... -55°C to +125°C
Storage Temperature ..................................................................................................................... -65°C to + 150°C
Voltage on EA# Pin to VSS ...................................................................................................................................................... -0.5V to +14.0V
Transient Voltage (<20ns) on Any Other Pin to VSS ..................................................................................................... -1.0V to +6.5V
Maximum IOL per I/O Pins P1.5, P1.6, P1.7...................................................................................................... 20mA
Maximum IOL per I/O for All Other Pins............................................................................................................. 15mA
Package Power Dissipation Capability (TA = 25°C) ........................................................................................... 1.5W
Through Hole Lead Soldering Temperature (10 Seconds) .............................................................................. 300°C
Surface Mount Lead Soldering Temperature (3 Seconds) ............................................................................... 240°C
Output Short Circuit Current(1) ................................................................................................................................................................... 50mA
Note (1) Outputs shorted for no more than one second. No more than one output shorted at a time.
(Based on package heat transfer limitations, not device power consumption.)
NOTICE: This specification contains preliminary information on new products in production. The specifications are subject to change
without notice.
Operation Range
TABLE 11: OPERATING RANGE
Symbol
Description
Min.
Max
Unit
TA
Ambient Temperature Under Bias
Standard
0
-40
2.7
0
+70
+85
5.5
33
°C
°C
V
MHz
MHz
Industrial
Supply Voltage
Oscillator Frequency
For In-Application Programming
VDD
fOSC
0.25
33
344 PGM T11.0
TABLE 12: RELIABILITY CHARACTERISTICS
Symbol
Parameter
Minimum Specification
Units
Test Method
NEND
TDR
VZAP_HBM
Endurance
Data Retention
ESD Susceptibility
Human Body Model
ESD Susceptibility
Machine Model
10,000
100
2000
Cycles
Years
Volts
MIL-STD-883, Method 1033
JEDEC Standard A103
JEDEC Standard A114
(1)
(1)
(1)
VZAP_MM
200
Volts
JEDEC Standard A115
(1)
ILTH
Latch Up
100+IDD
mA
JEDEC Standard 78
Note: (1)This parameter is measured only for initial qualification and after a design or process change that
344 PGM T12.1
could affect this parameter.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
38
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 13A: DC ELECTRICAL CHARACTERISTICS
TAMB = O°C TO + 70°C OR -40°C TO +85°C, 33MHZ DEVICES; 5V ±10%; VSS = 0V
1
Symbol
Parameter
Test Conditions
Limits
Units
Min
Max
4.5 < VDD < 5.5
4.5 < VDD < 5.5
4.5 < VDD < 5.5
VDD = 4.5V
VIL
VIH
VIH1
VOL
Input Low Voltage
-0.5
0.2VDD + 0.9
0.2VDD - 0.1
VDD + 0.5
VDD + 0.5
V
V
V
2
Input High Voltage (ports 0,1,2,3)
Input High Voltage (XTAL1, RST)
Output Low Voltage
0.7VDD
3
IOL = 16mA
1.0
(Ports 1.5, 1.6, 1.7)
V
V
DD = 4.5V
VOL
Output Low Voltage
IOL = 100µA 1
IOL = 1.6mA 1
IOL = 3.5mA 1
VDD = 4.5V
0.3
0.45
1.0
(Ports 1, 2, 3) 5
V
V
V
4
5
VOL1
Output Low Voltage
(Port 0, ALE, PSEN#) 4,5
0.3
0.45
I
OL = 200µA 1
IOL = 3.2mA 1
VDD = 4.5V
V
V
6
VOH
Output High Voltage
(Ports 1, 2, 3, ALE, PSEN#) 2
VDD - 0.3
V
V
V
IOH = -10µA
VDD - 0.7
IOH = -30µA
IOH = -60µA
7
VDD – 1.5
V
DD = 4.5V
VOH1
Output High Voltage
(Port 0 in External Bus Mode) 2
VDD - 0.3
VDD - 0.7
-1
V
V
µA
IOH = -200µA
IOH = -3.2mA
8
V
IN = 0.4V
-75
-650
±10
IIL
ITL
ILI
Logical 0 Input Current
(Ports 1, 2, 3)
Logical 1-to-0 Transition Current
(Ports 1, 2, 3) 3
9
µA
µA
VIN = 2V
0.45 < VIN
VDD-0.3
<
Input Leakage Current (Port 0)
10
11
12
13
14
15
16
k
pF
40
225
15
RRST
CIO
IDD
RST Pulldown Resistor
Pin Capacitance6
Power Supply Current 7
In-Application Mode
@ 12 MHz
@ 33 MHz
Active Mode
@ 12 MHz
@ 33 MHz
Idle Mode
@ 1 MHz, 25°C
mA
mA
70
88
mA
mA
25
45
mA
mA
µA
12
24
100
125
@ 12 MHz
@ 33 MHz
Standby (Stop Clock) Mode
Tamb =0°C to + 70°C
Tamb =-40°C to +85°C
µA
Minimum VDD = 2.7V
Tamb =0°C to + 70°C
Power Down Mode
µA
µA
40
50
Tamb =-40°C to +85°C
344 PGM T13A.5
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
39
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
TABLE 13B: DC ELECTRICAL CHARACTERISTICS
TAMB = O°C TO + 70°C OR -40°C TO +85°C, 12 MHZ DEVICES; 3V ±10%; VSS = 0V
Symbol
Parameter
Test Conditions
Limits
Units
Min
Max
2.7 < VDD < 3.3
2.7 < VDD < 3.3
2.7 < VDD < 3.3
VDD = 2.7V
VIL
VIH
VIH1
VOL
Input Low Voltage
-0.5
0.2VDD + 0.9
0.7
VDD + 0.5
VDD + 0.5
V
V
V
Input High Voltage (ports 0,1,2,3)
Input High Voltage (XTAL1, RST)
Output Low Voltage
0.7VDD
IOL = 16mA
1.0
(Ports 1.5, 1.6, 1.7)
V
VDD = 2.7V
IOL = 100µA 1
IOL = 1.6mA 1
IOL = 3.5mA 1
VDD = 2.7V
VOL
Output Low Voltage
(Ports 1, 2, 3) 5
V
V
V
0.3
0.45
1.0
VOL1
Output Low Voltage
(Port 0, ALE, PSEN#) 4,5
I
OL = 200µA 1
V
V
0.3
0.45
IOL = 3.2mA 1
VDD = 2.7V
VOH
Output High Voltage
(Ports 1, 2, 3, ALE, PSEN#) 2
VDD - 0.3
IOH = -10µA
V
V
V
VDD - 0.7
IOH = -30µA
IOH = -60µA
VDD – 1.5
V
DD = 2.7V
VOH1
Output High Voltage
(Port 0 in External Bus Mode) 2
VDD - 0.3
VDD - 0.7
-1
IOH = -200µA
IOH = -3.2mA
V
V
µA
V
IN = 0.4V
-75
-650
±10
IIL
ITL
ILI
Logical 0 Input Current
(Ports 1, 2, 3)
Logical 1-to-0 Transition Current
(Ports 1, 2, 3) 3
VIN = 2V
µA
µA
0.45 < VIN
VDD-0.3
<
Input Leakage Current (Port 0)
40
225
15
k
pF
RRST
CIO
RST Pulldown Resistor
Pin Capacitance6
@ 1 MHz, 25°C
IDD
Power Supply Current 7
In-Application Mode
Active Mode
Idle Mode
Standby (Stop Clock) Mode
70
22
6.5
70
88
mA
mA
mA
µA
Tamb =0°C to + 70°C
Tamb =-40°C to +85°C
µA
Minimum VDD = 2.7V
Tamb =0°C to + 70°C
Power Down Mode
40
50
µA
µA
Tamb =-40°C to +85°C
344 PGM T13B.3
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
40
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
NOTES:
1. Capacitive loading on Ports 0 & 2 may cause spurious noise to be superimposed on the VOLs of ALE and Ports 1 & 3. The noise due to
external bus capacitance discharging into the Port 0 & 2 pins when the pins make 1 -to- 0 transitions during bus operations. In the worst
cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify ALE
with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input.
2. Capacitive loading on Ports 0 & 2 may cause the VOH on ALE and PSEN# to momentarily fall below the VDD - 0.7 specification when the
address bits are stabilizing.
1
3. Pins of Ports 1, 2 & 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when Vin is approximately 2V.
2
4. Load capacitance for Port 0, ALE & PSEN#= 100pF, load capacitance for all other outputs= 80pF.
5. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin:
Maximum IOL per 8-bit port:
Maximum IOL total for all outputs:
15mA
26mA
71mA
3
If IOL exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
6. Pin capacitance is characterized but not tested. EA# is 25pF (max).
4
7. See Figures 22, 23, 24 and 25 for test conditions. Minimum VDD for Power Down is 2.7V.
5
V
V
DD
I
DD
I
DD
DD
V
V
V
V
DD
P0
DD
DD
P0
DD
6
V
DD
RST
EA#
RST
EA#
7
8XC5X
8XC5X
XTAL2
XTAL1
(NC)
XTAL2
XTAL1
(NC)
CLOCK
SIGNAL
CLOCK
SIGNAL
8
V
V
SS
SS
344 ILL F26.0
344 ILL F24.0
9
All other pins disconnected
All other pins disconnected
FIGURE 22: IDD TEST CONDITION, ACTIVE MODE
FIGURE 23: IDD TEST CONDITION, IDLE MODE
10
11
12
13
14
15
16
V
DD
I
V
V
DD
I
DD = 5V
V
= 3 or 5V
V
DD
DD
DD
V
V
DD
P0
DD
V
DD
DD
P0
RST
EA#
RST
EA#
8XC5X
8XC5X
XTAL2
XTAL1
(NC)
XTAL2
XTAL1
(NC)
V
SS
V
SS
344 ILL F33.3
344 ILL F25.2
All other pins disconnected
All other pins disconnected
FIGURE 25: IDD TEST CONDITION, STANDBY (STOP CLOCK)
MODE
FIGURE 24: IDD TEST CONDITION, POWER DOWN MODE
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
41
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
AC ELECTRICAL CHARACTERISTICS
AC Characteristics: (Over Operating Conditions; Load Capacitance for Port 0, ALE, and PSEN# = 100pF; Load
Capacitance for All Other Outputs = 80pF)
TABLE 14: AC ELECTRICAL CHARACTERISTICS
TAMB = 0°C TO +70°C OR -40°C TO +85°C, VDD = 3V±10% @ 12MHZ, 5V±10% @ 33MHZ, VSS = 0
Symbol
Parameter
Oscillator
Units
12MHz
33MHz
Variable
Min
Max
Min
Max
Min.
Max.
1/TCLCL
TLHLL
Oscillator Frequency
ALE Pulse Width
0
33
MHz
ns
127
43
20
5
2TCLCL - 40
TAVLL
Address Valid to ALE Low
TCLCL - 40 (5V)
TCLCL - 25 (3V)
ns
ns
TLLAX
TLLIV
TLLPL
Address Hold After ALE Low
ALE Low to Valid Instr In
ALE Low to PSEN# Low
53
TCLCL - 30 (5V)
TCLCL - 25 (3V)
ns
ns
5
234
145
4TCLCL - 100 (5V)
4TCLCL - 65 (3V)
ns
ns
56
53
TCLCL - 30 (5V)
TCLCL - 25 (3V)
ns
ns
5
TPLPH
TPLIV
PSEN# Pulse Width
205
46
3TCLCL - 45
ns
PSEN# Low to Valid Instr In
3TCLCL - 105 (5V)
3TCLCL - 55 (3V)
ns
ns
35
5
TPXIX
TPXIZ
Input Instr Hold After PSEN#
Input Instr Float After PSEN#
0
ns
59
312
10
TCLCL - 25 (5V)
TCLCL - 25 (3V)
ns
ns
TAVIV
Address to Valid Instr In
5TCLCL - 105 (5V)
5TCLCL - 80 (3V)
ns
ns
71
10
TPLAZ
TRLRH
TWLWH
TRLDV
PSEN# Low to Address Float
RD# Pulse Width
10
ns
ns
ns
400
400
82
82
6TCLCL - 100
6TCLCL - 100
Write Pulse Width (WE#)
RD# Low to Valid Data In
252
5TCLCL - 165 (5V)
5TCLCL - 90 (3V)
ns
ns
61
TRHDX
TRHDZ
Data Hold After RD#
Data Float After RD#
0
0
0
ns
107
517
585
300
2TCLCL - 60 (5V)
2TCLCL - 25 (3V)
ns
ns
35
TLLDV
TAVDV
ALE Low to Valid Data In
Address to Valid Data In
8TCLCL - 150 (5V)
8TCLCL - 90 (3V)
ns
ns
150
9TCLCL - 165 (5V)
9TCLCL - 90 (3V)
ns
ns
180
140
TLLWL
TAVWL
ALE Low to RD# or WR# Low
Address to RD# or WR# Low
200
203
40
46
0
3TCLCL - 50
3TCLCL + 50
ns
4TCLCL – 130 (5V)
4TCLCL – 75 (3V)
ns
ns
TQVWX
TWHQX
TQVWH
Data Valid to WR# Transition
Data Hold After WR#
33
33
TCLCL - 50 (5V)
TCLCL - 30 (3V)
ns
ns
TCLCL - 50 (5V)
TCLCL - 27 (3V)
ns
ns
3
Data Valid to WR# High
433
7TCLCL - 150 (5V)
7TCLCL - 70 (3V)
ns
ns
140
TRLAZ
RD# Low to Address Float
0
0
0
ns
TWHLH
RD# to WR# High to ALE High
43
123
TCLCL - 40 (5V)
TCLCL - 25 (3V)
TCLCL + 40 (5V)
TCLCL + 25 (3V)
ns
ns
5
55
344 PGM T14.2
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
42
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
AC CHARACTERISTICS
Explanation of Symbols
P: PSEN#
1
Eachtimingsymbolhas5characters. Thefirstcharacter
is always a ‘T’ (stands for time). The other characters,
depending on their positions, stand for the name of a
signal or the logical status of that signal. The following is
a list of all the characters and what they stand for.
Q: Output data
R: RD# signal
2
T: Time
A: Address
V: Valid
3
C: Clock
W: WR# signal
D Input data
X: No longer a valid logic level
Z: High Impedance (Float)
For example:
4
H: Logic level HIGH
I: Instruction (program memory contents).
L: Logic level LOW or ALE
TAVLL=Time from Address Valid to ALE Low
TLLPL=Time from ALE Low to PSEN# Low
5
6
V
V
+0.1V
-0.1V
IHT
LOAD
V
V
-0.1V
OH
OL
V
HT
Timing Reference
Points
V
LOAD
V
7
V
+0.1V
LT
V
LOAD
ILT
344 ILL F28a.2
344 ILL F28b.1
AC Inputs during testing are driven at V
(V
IHT DD
-0.5V) for Logic "1" and
For timing purposes a port pin is no longer floating when a 100 mV
change from load voltage occurs, and begins to float when a 100 mV
8
V
(0.45V) for a Logic "0". Measurement reference points for inputs and
ILT
outputs are at V
(0.2V
+ 0.9) and V (0.2V
- 0.1)
change from the loaded V
/V
level occurs. I /I = ± 20mA.
HT
DD LT
DD
OH OL
OL OH
Note: V - V
Test
Test
HIGH Test
LOW Test
HT HIGH
V
V
V
- V
-V
LT
LOW
9
IHT INPUT
- V
ILT INPUT
AC TESTING INPUT/OUTPUT
FIGURE 26: AC TESTING INPUT/OUTPUT, FLOAT WAVEFORM
FLOAT WAVEFORM
10
11
12
13
14
15
16
T
LHLL
ALE
T
PLPH
T
T
LLIV
AVLL
T
LLPL
T
PLIV
PSEN#
T
PLAZ
T
PXIZ
PXIX
INSTR IN
T
LLAX
T
A7 - A0
PORT 0
PORT 2
A7 - A0
T
AVIV
A15 - A8
A15 - A8
344 ILL F13.3
FIGURE 27: EXTERNAL PROGRAM MEMORY READ CYCLE
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
43
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
T
LHLL
ALE
T
WHLH
PSEN#
T
LLDV
T
RLRH
T
T
LLWL
RD#
T
LLAX
T
RHDZ
RLDV
T
AVLL
T
RLAZ
T
RHDX
A7-A0 FROM PCL
A7-A0 FROM RI or DPL
DATA IN
INSTR IN
PORT 0
PORT 2
T
AVWL
T
AVDV
P2[7:0] or A15-A8 FROM DPH
A15-A8 FROM PCH
344 ILL F14.3
FIGURE 28: EXTERNAL DATA MEMORY READ CYCLE
T
LHLL
ALE
T
WHLH
PSEN#
T
T
WLWH
LLWL
WR#
T
T
LLAX
T
WHQX
T
QVWX
AVLL
T
QVWH
A7-A0 FROM RI or DPL
PORT 0
PORT 2
DATA OUT
A7-A0 FROM PCL
INSTR IN
T
AVWL
P2[7:0] or A15-A8 FROM DPH
A15-A8 FROM PCH
344 ILL F15.3
FIGURE 29: EXTERNAL DATA MEMORY WRITE CYCLE
TABLE 15: EXTERNAL CLOCK DRIVE
Symbol
Parameter
Oscillator
Units
12MHz
Min Max
33MHz
Min Max
Variable
Min.
Max.
1/TCLCL
TCHCX
TCLCX
TCLCH
TCHCL
Oscillator Frequency
High Time
0
33
MHz
ns
0.35TCLCL
0.35TCLCL
0.65TCLCL
0.65TCLCL
Low Time
ns
Rise Time
20
20
5
5
ns
Fall Time
ns
344 PGM T15.2
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
44
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
V
DD = -0.5
1
0.7 V
DD
-0.1
T
T
CHCX
0.2 V
0.45 V
DD
T
2
CLCX
CLCH
T
CLCL
T
CHCL
344 ILL F30.0
3
FIGURE 30: EXTERNAL CLOCK DRIVE WAVEFORM
4
5
TABLE 16: SERIAL PORT TIMING
Symbol
Parameter
Oscillator
Units
12MHz
33MHz
Variable
Min.
6
Min
Max
Min
Max
Max.
TXLXL
TQVXH
TXHQX
TXHDX
TXHDV
Serial Port Clock Cycle
Time
0
700
50
0
0.36
167
12TCLCL
ms
ns
7
Output Data Setup
to Clock Rising Edge
10TCLCL - 133
8
Output Data Hold After
Clock Rising Edge
2TCLCL - 117
2TCLCL - 50
ns
ns
10
0
Input Data Hold After
Clock Rising Edge
0
ns
9
Clock Rising Edge
to Input Data Valid
700
167
10TCLCL - 133
ns
10
11
12
13
14
15
16
344 PGM T16.1
INSTRUCTION
ALE
0
1
2
3
4
5
6
7
8
T
XLXL
CLOCK
T
XHQX
T
QVXH
0
1
2
3
4
5
6
7
OUTPUT DATA
T
XHDX
T
SET TI
WRITE TO SBUF
INPUT DATA
XHDV
VALID
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET R I
CLEAR RI
344 ILL F29.0
FIGURE 31: SHIFT REGISTER MODE TIMING WAVEFORMS
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
45
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
PRODUCT ORDERING INFORMATION
Product Identification Descriptor
Speed Suffix 1 Suffix 2
33 X X X X
Device
SST89C5x
-
-
-
Package Modifier
I = 40 pins
J = 44 pins
Package Type
P = PDIP
N = PLCC
TQ = TQFP
Operation Temperature
C = Commercial = 0° to 70°C
I = Industrial = -40° to 85°C
Release ID
Blank = Initial release
A = First enhancement
Operating Frequency
33 = 0-33MHz
Feature Set and Flash Memory Size
54 = C52 feature set + 16(20)* KByte
58 = C52 feature set + 32(36)* KByte
* = 4K additional flash can be
enabled via VIS bit in SFCF
Voltage Range
C = 2.7-5.5V
Device Family
89 = C51 Core
Part Number Valid Combinations
SST89C54 Valid combinations
Part Number
Package
PDIP
Pins
40
VDD
Speed
Temperature
Commercial
Commercial
Commercial
Industrial
SST89C54-33-C-PI
SST89C54-33-C-NJ
SST89C54-33-C-TQJ
SST89C54-33-I-PI
SST89C54-33-I-NJ
SST89C54-33-I-TQJ
2.7-5.5
2.7-5.5
2.7-5.5
2.7-5.5
2.7-5.5
2.7-5.5
0-33MHz
0-33MHz
0-33MHz
0-33MHz
0-33MHz
0-33MHz
PLCC
TQFP
PDIP
44
44
40
PLCC
TQFP
44
Industrial
44
Industrial
SST89C58 Valid combinations
Part Number
Package
PDIP
Pins
40
VDD
Speed
Temperature
Commercial
Commercial
Commercial
Industrial
SST89C58-33-C-PI
SST89C58-33-C-NJ
SST89C58-33-C-TQJ
SST89C58-33-I-PI
SST89C58-33-I-NJ
SST89C58-33-I-TQJ
2.7-5.5
2.7-5.5
2.7-5.5
2.7-5.5
2.7-5.5
2.7-5.5
0-33MHz
0-33MHz
0-33MHz
0-33MHz
0-33MHz
0-33MHz
PLCC
TQFP
PDIP
44
44
40
PLCC
TQFP
44
Industrial
44
Industrial
Example: Valid combinations are those products in mass production or will be in mass production. Consult your SST sales representative
to confirm availability and to determine availability of new combinations.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
46
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Part Number Cross-Reference Guide
Intel
i87C54
i87C58
i87L54
i87L58
i87C51FB
i87C51FC
SST
package
P N TQ
P N TQ
N TQ
N TQ
P N TQ
P N TQ
1
16K EPROM & 256B RAM
SST89C54
SST89C58
SST89C54
SST89C58
SST89C54*
SST89C58*
4K Flash, 16K Flash & 256B RAM
32K EPROM & 256B RAM
16K ROM (OTP) & 256B RAM
32K ROM (OTP) & 256B RAM
16K EPROM & 256B RAM
32K EPROM & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
2
Atmel
SST
package
P N TQ
P N TQ
P N TQ
P N TQ
P N TQ
P N TQ
3
AT89C52
AT89LV52
AT89S53
AT89LS53
AT89C55
AT89LV55
8K Flash & 256B RAM
8K Flash & 256B RAM
12K Flash & 256B RAM
12K Flash & 256B RAM
20K Flash & 256B RAM
20K Flash & 256B RAM
SST89C54
SST89C54
SST89C54*
SST89C54*
SST89C58*
SST89C58*
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4
Temic
SST
package
P N TQ
P N TQ
P N TQ
P N TQ
P N TQ
P N TQ
5
80C51
80C52
83C154
83C154D
87C51
87C52
4K ROM & 256B RAM
8K ROM & 256B RAM
16K ROM & 256B RAM
32K ROM & 256B RAM
4K EPROM & 256B RAM
8K EPROM & 256B RAM
SST89C54*
SST89C54
SST89C54
SST89C58
SST89C54*
SST89C54
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
6
7
Philips
SST
package
P N TQ
P N TQ
P N TQ
P N TQ
P N TQ
P N TQ
P N
P80C54
P80C58
P87C54
P87C58
P87C524
P87C528
P83C524
P83C528
P89CE558
16K ROM & 256B RAM
32K ROM & 256B RAM
16K EPROM & 256B RAM
32K EPROM & 256B RAM
16K EPROM & 512B RAM
32K EPROM & 512B RAM
16K ROM & 512B RAM
32K MROM & 512B RAM
32K Flash & 1K RAM
SST89C54
SST89C58
SST89C54
SST89C58
SST89C54*
SST89C58*
SST89C54*
SST89C58*
SST89C58*
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
8
9
P N TQ
Winbond
W78C54
W78C58
W78E54
W78E58
SST
package
P N TQ
P N TQ
P N TQ
P N TQ
10
11
12
13
14
15
16
16K MROM & 256B RAM
32K MROM & 256B RAM
16K EEPROM & 256B RAM
32K EEPROM & 256B RAM
SST89C54
SST89C58
SST89C54
SST89C58
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 32K Flash & 256B RAM
ISSI
SST
package
P N TQ
P N
IS80C52
IS89C51
IS89C52
8K ROM & 256B RAM
4K Flash & 128B RAM
8K Flash & 256B RAM
SST89C54
SST89C54
SST89C54
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
P N
Dallas
SST
SST89C54*
SST89C54*
package
P N TQ
P N TQ
DS83C520
DS87C520
256B RAM
16K MROM & 256B RAM
16K EPROM ( OTP ) &
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
Siemens
SST
package
C501-1R 8K ROM & 256B RAM
C501-1E 8K ROM (OTP) & 256B RAM
C513A-H 12K EPROM & 512B RAM
C503-1R 8K ROM & 256B RAM
SST89C54
SST89C54
SST89C54*
SST89C54*
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
4K Flash, 16K Flash & 256B RAM
P N
P N
N
N
C504-2R 16K ROM & 512B RAM
SST89C54*
4K Flash, 16K Flash & 256B RAM
TQ
P: PDIP
N: PLCC
TQ: TQFP
NOTE: The SST89C58 can be substituted for any SST89C54 listing above.
NOTE: The SST89C59 can be substituted for any SST89C54 or SST89C58 listing above.
* Indicates SST similar function and not direct replacement/socket compatible.
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
47
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
PACKAGING DIAGRAMS
40
C
L
.600
.625
1
Pin #1 Identifier
.530
.557
2.020
2.070
.065
.075
12˚
4 places
.220 Max.
Base Plane
Seating Plane
.015 Min.
0˚
15˚
.008
.012
.100 †
.200
.063
.090
.045
.055
.015
.022
.100 BSC
.600 BSC
Note:
1. Complies with JEDEC publication 95 MS-011 AC dimensions (except as noted), although some dimensions may be more stringent.
† = JEDEC min is .115; SST min is less stringent
40.pdipPI-ILL.6
2. All linear dimensions are in inches (min/max).
3. Dimensions do not include mold flash. Maximum allowable mold flash is .010 inches.
40-PIN PLASTIC DUAL-IN-LINE PACKAGE (PDIP)
SST PACKAGE CODE: PI
TOP VIEW
SIDE VIEW
BOTTOM VIEW
.685
.695
.646
.656
Optional
Pin #1 Identifier
.147
.158
†
.020 R.
MAX.
.042
.048
.025
.045
.042
.056
R.
x45˚
1
44
.042
.048
.013
.021
.685
.695
.646
.656
†
.500 .590
REF. .630
.026
.032
.050
BSC.
.020 Min.
.100
.112
.050
BSC.
.026
.032
.165
.180
44.PLCC.NJ-ILL.6
Note:
1. Complies with JEDEC publication 95 MS-018 AC dimensions (except as noted), although some dimensions may be more stringent.
† = JEDEC min is .650; SST min is less stringent
2. All linear dimensions are in inches (min/max).
3. Dimensions do not include mold flash. Maximum allowable mold flash is .008 inches.
4. Coplanarity: ± 4 mils.
44-LEAD PLASTIC LEAD CHIP CARRIER (PLCC)
SST PACKAGE CODE: NJ
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
48
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
1
2
3
33
34
23
22
.020
4
.80 BSC
10.0 12.0
BSC BSC
1.20
1.05
.95
.09
.20
max.
5
0˚- 7˚
.75
.45
.30
.45
.15
.05
44
1
12
1.00 ref
6
11
Pin 1 Identifier(s)
(either or both)
0.20
.80
.30
.45
BSC
7
10.0
44.tqfp-TQJ-ILL.3
BSC
12.0
BSC
8
Note:
1. Complies with JEDEC publication 95 MS-026 ACB dimensions, although some dimensions may be more stringent.
2. All linear dimensions are in mm (min/max).
9
3. Coplanarity: 0.1 (±0.05) mm.
44-LEAD THIN QUAD FLAT PACK (TQFP)
SST PACKAGE CODE: TQJ
10
11
12
13
14
15
16
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
49
FlashFlex51 MCU
SST89C54 / SST89C58
Preliminary Specifications
Silicon Storage Technology, Inc. • 1171 Sonora Court • Sunnyvale, CA 94086 • Telephone 408-735-9110 • Fax 408-735-9036
www.SuperFlash.com or www.ssti.com • Literature FaxBack 888-221-1178, International 732-544-2873
© 2000 Silicon Storage Technology, Inc.
344-2 8/00
50
相关型号：
©2020 ICPDF网 联系我们和版权申明