LD29150DT33R [STMICROELECTRONICS]
1.5 A, very low drop voltage regulators; 1.5 A ，非常低的压差电压稳压器
| 型号： | LD29150DT33R |
| 厂家： | 
ST |
| 描述： | 1.5 A, very low drop voltage regulators |
| 文件： | 总22页 (文件大小：551K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LD29150xx
1.5 A, very low drop voltage regulators
Datasheet − production data
Features
■ Very low dropout voltage (typ. 0.4 at 1.5 A)
■ Guaranteed output current up to 1.5 A
■ Fixed and adjustable output voltage ( 1% at
25 °C)
DPAK
PPAK
■ Internal current and thermal limit
■ Logic controlled electronic shutdown available
in PPAK and P²PAK
Description
The LD29150xx is a high current, high accuracy,
low-dropout voltage regulator series. These
regulators feature 400 mV dropout voltage and
very low ground current. Designed for high
current loads, these devices are also used in
lower current, extremely low dropout-critical
systems, where their tiny dropout voltage and
ground current values are important attributes.
Typical applications are in power supply switching
post regulation, series power supply for monitors,
series power supply for VCRs and TVs, computer
systems and battery powered systems.
P²PAK
Table 1.
Device summary
Order codes
PPAK
Part numbers
Output voltages
DPAK
P²PAK
LD29150XX18
LD29150XX25
LD29150XX33
LD29150XX50
LD29150XX
LD29150DT18R
LD29150DT25R
LD29150DT33R
LD29150DT50R
1.8 V
2.5 V
3.3 V
5.0 V
ADJ
LD29150P2T33R
LD29150PT50R
LD29150PTR
September 2012
Doc ID 9614 Rev 18
1/22
This is information on a product in full production.
www.st.com
22
Contents
LD29150xx
Contents
1
2
3
4
5
6
7
8
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2/22
Doc ID 9614 Rev 18
LD29150xx
1
Diagram
Diagram
Figure 1.
Schematic diagram for adjustable version
Figure 2.
Schematic diagram for fixed version
* Only for version with inhibit function.
Doc ID 9614 Rev 18
3/22
Pin configuration
LD29150xx
2
Pin configuration
Figure 3.
Pin connections (top view)
PPAK
P²PAK
DPAK
* Not connected for fixed version.
4/22
Doc ID 9614 Rev 18
LD29150xx
3
Typical application
Typical application
Figure 4.
Application circuit
VO = VREF (1 + R1/R2)
* Only for version with inhibit function.
Doc ID 9614 Rev 18
5/22
Maximum ratings
LD29150xx
4
Maximum ratings
Table 2.
Absolute maximum ratings
Parameter
Symbol
Value
Unit
VI
VO
DC input voltage
30 (1)
-0.3 to 20
V
V
DC output voltage
VINH
IO
Inhibit input voltage
-0.3 to 20
V
Output current
Internally limited
Internally limited
-55 to 150
mA
mW
°C
°C
PD
Power dissipation
TSTG
TOP
Storage temperature range
Operating junction temperature range
-40 to 125
1. Above 14 V the device is automatically in shut-down.
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied.
Table 3.
Symbol
Thermal data
Parameter
DPAK
PPAK
P²PAK
Unit
RthJA
RthJC
Thermal resistance junction-ambient
Thermal resistance junction-case
100
8
100
8
60
3
°C/W
°C/W
6/22
Doc ID 9614 Rev 18
LD29150xx
Electrical characteristics
5
Electrical characteristics
IO = 10 mA, TJ = 25 °C, VI = 3.8 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless
otherwise specified.
Table 4.
Symbol
Electrical characteristics of LD29150#18
Parameter
Test conditions
Min.
Typ.
Max.
Unit
1.782
1.764
1.8
1.818
1.836
1.0
IO = 10 mA to 1.5 A, VI = 3 to 7.3 V
TJ = - 40 to 125°C
VO
Output voltage
V
ΔVO
ΔVO
Load regulation
Line regulation
IO = 10 mA to 1.5 A
VI = 3 to 13 V
0.2
%
%
0.06
0.5
f = 120 Hz, VI = 3.8 1 V, IO = 0.75 A
(Note 1)
SVR Supply voltage rejection
62
72
dB
IO = 250 mA, TJ = - 40 to 125°C (Note 2)
0.1
0.2
0.4
15
VDROP Dropout voltage
I
I
O = 0.75 A, TJ = - 40 to 125°C (Note 2)
O = 1.5 A, TJ = - 40 to 125°C (Note 2)
V
0.7
40
IO = 0.75 A, TJ = - 40 to 125°C
IO = 1.5 A, TJ = - 40 to 125°C
mA
Iq
Quiescent current
30
80
VI = 13 V, VINH = GND, TJ = - 40 to 125°C
VI - VO = 5.5 V
130
2.2
180
µA
A
Isc
VIL
VIH
IINH
eN
Short circuit current
Control input logic low
Control input logic high
Control input current
Output noise voltage
OFF MODE, (Note 3), TJ = - 40 to 125°C
ON MODE, (Note 3), TJ = - 40 to 125°C
TJ = - 40 to 125°C, VINH = 13 V
BP = 10 Hz to 100 kHz, IO = 100 mA
0.8
10
V
2
V
5
µA
72
µVRMS
°C
TSHDN Thermal shutdown
150
Note:
1
2
Guaranteed by design.
Dropout voltage is defined as the input-to-output differential when the output voltage drops
to 99% of its nominal value with VO + 1 V applied to VI.
3
Only for version with Inhibit function.
Doc ID 9614 Rev 18
7/22
Electrical characteristics
LD29150xx
IO = 10 mA, TJ = 25 °C, VI = 4.5 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless
otherwise specified.
Table 5.
Symbol
Electrical characteristics of LD29150#25
Parameter
Test conditions
Min.
Typ.
Max.
Unit
2.475
2.45
2.5
2.525
2.55
1.0
IO = 10 mA to 1.5 A, VI = 3.5 to 8 V
TJ = - 40 to 125°C
VO
Output voltage
V
ΔVO
ΔVO
Load regulation
Line regulation
IO = 10 mA to 1.5 A
VI = 3.5 to 13 V
0.2
%
%
0.06
0.5
f = 120 Hz, VI = 4.5 1 V, IO = 0.75 A
(Note 1)
SVR Supply voltage rejection
55
70
dB
IO = 250 mA, TJ = - 40 to 125°C (Note 2)
0.1
0.2
0.4
15
VDROP Dropout voltage
I
O = 0.75 A, TJ = - 40 to 125°C (Note 2)
V
IO = 1.5 A, TJ = - 40 to 125°C (Note 2)
IO = 0.75 A, TJ = - 40 to 125°C
IO = 1.5 A, TJ = - 40 to 125°C
0.7
40
mA
Iq
Quiescent current
30
80
VI = 13 V, VINH = GND, TJ = - 40 to 125°C
VI - VO = 5.5 V
130
2.2
180
µA
A
Isc
VIL
VIH
IINH
eN
Short circuit current
Control input logic low
Control input logic high
Control input current
Output noise voltage
OFF MODE, (Note 3), TJ = - 40 to 125°C
ON MODE, (Note 3), TJ = - 40 to 125°C
TJ = - 40 to 125°C, VINH = 13 V
BP = 10 Hz to 100 kHz, IO = 100 mA
0.8
10
V
2
V
5
µA
100
150
µVRMS
°C
TSHDN Thermal shutdown
Note:
1
2
Guaranteed by design.
Dropout voltage is defined as the input-to-output differential when the output voltage drops
to 99% of its nominal value with VO + 1 V applied to VI.
3
Only for version with Inhibit function.
8/22
Doc ID 9614 Rev 18
LD29150xx
Electrical characteristics
IO = 10 mA, TJ = 25 °C, VI = 5.3 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless
otherwise specified.
Table 6.
Symbol
Electrical characteristics of LD29150#33
Parameter
Test conditions
Min.
Typ.
Max.
Unit
3.267
3.234
3.3
3.333
3.366
1.0
IO = 10 mA to 1.5 A, VI = 4.3 to 8.8 V
TJ = - 40 to 125°C
VO
Output voltage
V
ΔVO
ΔVO
Load regulation
Line regulation
IO = 10 mA to 1.5 A
VI = 4.3 to 13 V
0.2
%
%
0.06
0.5
f = 120 Hz, VI = 5.3 1 V, IO = 0.75 A
(Note 1)
SVR Supply voltage rejection
52
67
dB
IO = 250 mA, TJ = - 40 to 125°C (Note 2)
0.1
0.2
0.4
15
VDROP Dropout voltage
I
O = 0.75 A, TJ = - 40 to 125°C (Note 2)
V
IO = 1.5 A, TJ = - 40 to 125°C (Note 2)
IO = 0.75 A, TJ = - 40 to 125°C
IO = 1.5 A, TJ = - 40 to 125°C
0.7
40
mA
Iq
Quiescent current
30
80
VI = 13 V, VINH = GND, TJ = - 40 to 125°C
VI - VO = 5.5 V
130
2.2
180
µA
A
Isc
VIL
VIH
IINH
eN
Short circuit current
Control input logic low
Control input logic high
Control input current
Output noise voltage
OFF MODE, (Note 3), TJ = - 40 to 125°C
ON MODE, (Note 3), TJ = - 40 to 125°C
TJ = - 40 to 125°C, VINH = 13 V
BP = 10 Hz to 100 kHz, IO = 100 mA
0.8
10
V
2
V
5
µA
132
150
µVRMS
°C
TSHDN Thermal shutdown
Note:
1
2
Guaranteed by design.
Dropout voltage is defined as the input-to-output differential when the output voltage drops
to 99% of its nominal value with VO + 1 V applied to VI.
3
Only for version with Inhibit function.
Doc ID 9614 Rev 18
9/22
Electrical characteristics
LD29150xx
IO = 10 mA, TJ = 25 °C, VI = 7 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF, unless
otherwise specified.
Table 7.
Symbol
Electrical characteristics of LD29150#50
Parameter
Test conditions
Min.
Typ.
Max.
Unit
4.95
4.9
5
5.05
5.1
1.0
0.5
IO = 10 mA to 1.5 A, VI = 6 to 10.5 V
TJ = - 40 to 125°C
VO
Output voltage
V
ΔVO
ΔVO
Load regulation
Line regulation
IO = 10 mA to 1.5 A
VI = 6 to 13 V
0.2
%
%
0.06
f = 120 Hz, VI = 7 1 V, IO = 0.75 A
(Note 1)
SVR Supply voltage rejection
49
64
dB
IO = 250 mA, TJ = - 40 to 125°C (Note 2)
0.1
0.2
0.4
15
VDROP Dropout voltage
I
O = 0.75 A, TJ = - 40 to 125°C (Note 2)
V
IO = 1.5 A, TJ = - 40 to 125°C (Note 2)
IO = 0.75 A, TJ = - 40 to 125°C
IO = 1.5 A, TJ = - 40 to 125°C
0.7
40
mA
Iq
Quiescent current
30
80
VI = 13 V, VINH = GND, TJ = - 40 to 125°C
VI - VO = 5.5 V
130
2.2
180
µA
A
Isc
VIL
VIH
IINH
eN
Short circuit current
Control input logic low
Control input logic high
Control input current
Output noise voltage
OFF MODE, (Note 3), TJ = - 40 to 125°C
ON MODE, (Note 3), TJ = - 40 to 125°C
TJ = - 40 to 125°C, VINH = 13 V
BP = 10 Hz to 100 kHz, IO = 100 mA
0.8
10
V
2
V
5
µA
200
150
µVRMS
°C
TSHDN Thermal shutdown
Note:
1
2
Guaranteed by design.
Dropout voltage is defined as the input-to-output differential when the output voltage drops
to 99% of its nominal value with VO + 1 V applied to VI.
3
Only for version with Inhibit function.
10/22
Doc ID 9614 Rev 18
LD29150xx
Electrical characteristics
IO = 10 mA, TJ = 25 °C, VI = 3.23 V, VINH = 2 V (Note 3), CI = 330 nF, CO = 10 µF adjust pin
tied to output pin.
Table 8.
Symbol
Electrical characteristics of LD29150#ADJ
Parameter
Test conditions
Min.
Typ.
Max.
Unit
Minimum operating input
voltage
VI
IO = 10 mA to 1.5 A, TJ = - 40 to 125°C
2.5
V
ΔVO
ΔVO
Load regulation
Line regulation
IO = 10 mA to 1.5 A
0.2
1.0
0.5
%
%
VI = 2.5 V to 13 V, IO = 10 mA
0.06
1.23
-1%
-2%
+1%
+2%
I
O = 10 mA to 1.5 A, VI = 2.5 to 4.5 V
VREF Reference voltage
V
TJ = - 40 to 125°C (Note 2)
f = 120 Hz, VI = 3.23 1 V, IO = 0.75 A
(Note 1)
SVR Supply voltage rejection
45
75
dB
mA
IO = 0.75 A, TJ = - 40 to 125°C
IO = 1.5 A, TJ = - 40 to 125°C
15
30
40
80
180
1
Iq
Quiescent current
VI = 13 V, VINH = GND, TJ = - 40 to 125°C
TJ = - 40 to 125°C (Note 1)
130
µA
µA
A
IADJ
Isc
Adjust pin current
Short circuit current
Control input logic low
Control input logic high
Control input current
Output noise voltage
VI - VO = 5.5 V
2.2
VIL
VIH
IINH
eN
OFF MODE, (Note 3),TJ = - 40 to 125°C
ON MODE, (Note 3), TJ = - 40 to 125°C
TJ = - 40 to 125°C, VINH = 13 V
BP = 10 Hz to 100 kHz, IO = 100 mA
0.8
10
V
2
V
5
µA
µVRMS
°C
50
TSHDN Thermal shutdown
150
Note:
1
2
3
Guaranteed by design.
Reference voltage is measured between output and GND pin, with ADJ PIN tied to VOUT
Only for version with Inhibit function.
.
Doc ID 9614 Rev 18
11/22
Typical characteristics
LD29150xx
6
Typical characteristics
Figure 5.
Output voltage vs. temperature
Figure 6.
Reference voltage vs. temperature
Figure 7.
Dropout voltage vs. temperature
Figure 8.
Dropout voltage vs. output current
Figure 9.
Quiescent current vs. output
current (VI = 13 V)
Figure 10. Quiescent current vs. output
current (VI = 4.5 V)
12/22
Doc ID 9614 Rev 18
LD29150xx
Typical characteristics
Figure 11. Quiescent current vs. supply
voltage
Figure 12. Quiescent current vs. temperature
(IO = 10 mA)
Figure 13. Quiescent current vs. temperature Figure 14. Short circuit current vs.
(IO = 1.5 A) temperature
Figure 15. Adjust pin current vs. temperature Figure 16. Supply voltage rejection vs.
temperature
Doc ID 9614 Rev 18
13/22
Typical characteristics
LD29150xx
Figure 17. Output voltage vs. input voltage
Figure 18. Stability vs. CO
Figure 19. Line transient
Figure 20. Load transient
V =3.5 to 5.5V, I =10mA, V =2.5V, C =10µF
V =5V, I =10mA to 1.5A, V =2.5V, C =10µF
I O O O
I
O
O
O
Figure 21. Start-up time 10 mA
Figure 22. Start-up time 1.5 A
C =10µF, I =1.5A, V =2V, V =5V, V =7V
C =10µF, I =10mA, V =2V, V =5V, V =7V
O
O
INH
O
I
O
O
INH
O
I
14/22
Doc ID 9614 Rev 18
LD29150xx
Package mechanical data
7
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Doc ID 9614 Rev 18
15/22
Package mechanical data
LD29150xx
DPAK mechanical data
mm.
inch.
Typ.
Dim.
Min.
Typ.
Max.
Min.
Max.
A
A1
A2
b
2.2
0.9
2.4
1.1
0.23
0.9
5.4
0.6
0.6
6.2
0.086
0.035
0.001
0.025
0.204
0.017
0.019
0.236
0.094
0.043
0.009
0.035
0.212
0.023
0.023
0.244
0.03
0.64
5.2
b4
C
0.45
0.48
6
C2
D
D1
E
5.1
0.200
6.4
6.6
0.252
0.260
E1
e
4.7
0.185
0.090
2.28
e1
H
4.4
9.35
1
4.6
0.173
0.368
0.039
0.181
0.397
10.1
L
(L1)
L2
L4
R
2.8
0.8
0.110
0.031
0.6
0°
1
0.023
0.039
8°
0.2
0.008
V2
8°
0°
0068772-F
16/22
Doc ID 9614 Rev 18
LD29150xx
Package mechanical data
PPAK mechanical data
mm.
inch.
Dim.
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
B
2.2
0.9
2.4
1.1
0.23
0.6
5.4
0.6
0.6
6.2
0.086
0.035
0.001
0.015
0.204
0.017
0.019
0.236
0.094
0.043
0.009
0.023
0.212
0.023
0.023
0.244
0.03
0.4
5.2
B2
C
0.45
0.48
6
C2
D
D1
E
5.1
0.201
6.4
6.6
0.252
0.260
E1
e
4.7
0.185
1.27
0.050
G
4.9
5.25
2.7
10.1
1
0.193
0.093
0.368
0.206
0.106
0.397
0.039
0.039
G1
H
2.38
9.35
L2
L4
L5
L6
0.8
2.8
0.031
0.6
1
1
0.023
0.039
0.110
0078180-E
Doc ID 9614 Rev 18
17/22
Package mechanical data
LD29150xx
P2PAK mechanical data
mm.
inch.
Typ.
Dim.
Min.
Typ.
Max.
Min.
Max.
A
A1
A2
b
4.30
2.40
0.03
0.80
0.45
1.17
8.95
4.80
2.80
0.23
1.05
0.60
1.37
9.35
0.169
0.094
0.001
0.031
0.017
0.046
0.352
0.188
0.110
0.009
0.041
0.023
0.053
0.368
c
c2
D
D2
E
8
0.315
0.334
10.00
10.40
0.393
0.409
0.409
0.142
0.275
0.571
0.055
0.067
0.094
E1
e
8.5
3.20
6.60
13.70
1.25
0.90
1.55
3.60
7.00
14.50
1.40
1.70
2.40
0.126
0.260
0.539
0.049
0.035
0.061
e1
L
L2
L3
L5
R
0.40
0.016
V2
0°
8°
0°
8°
7226255/B
18/22
Doc ID 9614 Rev 18
LD29150xx
Package mechanical data
Tape & reel DPAK-PPAK mechanical data
mm.
Typ.
inch.
Typ.
Dim.
Min.
Max.
330
Min.
Max.
12.992
0.519
A
C
12.8
20.2
60
13.0
13.2
0.504
0.795
2.362
0.512
D
N
T
22.4
7.00
10.60
2.75
4.1
0.882
0.2.76
0.417
0.105
0.161
0.319
Ao
Bo
Ko
Po
P
6.80
10.40
2.55
3.9
6.90
10.50
2.65
4.0
0.268
0.409
0.100
0.153
0.311
0.272
0.413
0.104
0.157
0.315
7.9
8.0
8.1
Doc ID 9614 Rev 18
19/22
Package mechanical data
LD29150xx
Tape & reel D2PAK-P2PAK-D2PAK/A-P2PAK/A mechanical data
mm.
Typ.
inch.
Typ.
Dim.
Min.
Max.
180
Min.
Max.
7.086
0.519
A
C
D
12.8
20.2
60
13.0
13.2
0.504
0.795
2.362
0.512
N
T
14.4
10.70
15.90
5.00
4.1
0.567
0.421
0.626
0.197
0.161
0.476
Ao
Bo
Ko
Po
P
10.50
15.70
4.80
3.9
10.6
15.80
4.90
4.0
0.413
0.618
0.189
0.153
0.468
0.417
0.622
0.193
0.157
0.472
11.9
12.0
12.1
20/22
Doc ID 9614 Rev 18
LD29150xx
Revision history
8
Revision history
Table 9.
Date
Document revision history
Revision
Changes
Add figures 20 and 21, PPAK, TO-220 and TO-220FP mechanical
data updated.
17-Jun-2004
5
19-Jul-2004
08-Nov-2004
21-Mar-2005
21-Oct-2005
17-Oct-2006
13-Nov-2006
11-May-2007
15-Feb-2008
28-Jul-2009
22-Sep-2010
27-Oct-2010
6
Remove Package TO-220FP4.
Mistake Figure 7.
7
8
Add VO and VINH on Table 2.
Order Codes Has Been Updated.
Add new package P²PAK.
9
10
11
12
13
14
15
16
Add row TSHDN on tables of the electrical characteristics.
Order codes updated.
Added: Table 1 on page 1.
Modified: Table 1 on page 1.
Modified: Table 1 on page 1.
Updated: DPAK mechanical data on page 16.
Modified: pin connections for PPAK, P²PAK and DPAK Figure 3 on
page 4.
07-May-2012
06-Sep-2012
17
18
Updated: figure for P²PAK in cover page.
Doc ID 9614 Rev 18
21/22
LD29150xx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
22/22
Doc ID 9614 Rev 18
相关型号：
©2020 ICPDF网 联系我们和版权申明