LD39015M125R [STMICROELECTRONICS]
150 mA low quiescent current low noise voltage regulator; 150毫安低静态电流低噪声稳压器型号: | LD39015M125R |
厂家: | ST |
描述: | 150 mA low quiescent current low noise voltage regulator |
文件: | 总16页 (文件大小:298K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LD39015xx
150 mA low quiescent current
low noise voltage regulator
Features
■ Input voltage from 1.5 to 5.5 V
■ Ultra low dropout voltage (80 mV typ. at 100
mA load)
■ Very low quiescent current (18 µA typ. at no
load, 35 µA typ. at 150 mA load, 1 µA max in off
mode)
■ Very low noise without bypass capacitor
SOT666
SOT23-5L
(29 µV
at V
= 0.8 V)
RMS
OUT
■ Output voltage tolerance: 2.0% @ 25 °C
■ 150 mA guaranteed output current
from 1.5 V to 5.5 V with a typical dropout voltage
of 80 mV. It is stable with ceramic capacitor. The
ultra-low drop voltage, low quiescent current and
low noise features make it suitable for low power
battery-powered applications. Power supply
rejection is 65 dB at low frequencies and starts to
roll off at 10 kHz. Enable logic control function
puts the LD39015xx in shut-down mode allowing
a total current consumption lower than 1 µA. The
device also includes short-circuit constant current
limiting and thermal protection. Typical
■ Wide range of output voltages available on
request: 0.8 V to 3.3 V with 100 mV step
■ Logic-controlled electronic shutdown
■ Compatible with ceramic capacitors C = 1 µF
O
■ Internal current and thermal limit
■ Available in SOT666 and SOT23-5L packages
■ Temperature range: -40 °C to 125 °C
applications are mobile phones, personal digital
assistants (PDAs), cordless phones or similar
battery-powered systems.
Description
The LD39015xx series provides 150 mA
maximum current from an input voltage ranging
Table 1.
Device summary
Order codes
Part numbers
Output voltages
SOT666
SOT23-5L
LD39015XX08
LD39015XX10
LD39015XX12
LD39015XX125
LD39015XX15
LD39015XX18
LD39015XX25
LD39015XX33
LD39015XG08R
LD39015XG10R (1)
LD39015XG12R
LD39015M08R
LD39015M10R
LD39015M12R
LD39015M125R
LD39015M15R
LD39015M18R
LD39015M25R
LD39015M33R
0.8 V
1.0 V
1.2 V
1.25 V
1.5 V
1.8 V
2.5 V
3.3 V
LD39015XG15R (1)
LD39015XG18R (1)
LD39015XG25R (1)
LD39015XG33R
1. Available on request. Other voltages available on request from 0.8 V to 3.3 V in 100 mV step.
February 2009
Rev 3
1/16
www.st.com
16
Contents
LD39015xx
Contents
1
2
3
4
5
6
7
8
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2/16
LD39015xx
1
Diagram
Diagram
Figure 1.
Block diagram
OUT
IN
BandGap
1.22 V
R1
R2
Trimming
Thermal
Protection
Enable
EN
GND
3/16
Pin configuration
LD39015xx
2
Pin configuration
Figure 2.
Pin connection (top view)
SOT666
SOT23-5L
Table 2.
Pin description
Pin n°
Symbol
SOT23-5L
Function
SOT666
1
2
3
4
5
6
3
2
1
5
4
EN
GND
IN
Enable pin logic input: Low=shutdown, High=active
Common ground.
Input voltage of the LDO
Output voltage
OUT
NC
Not connected
NC
Not connected
4/16
LD39015xx
3
Typical application
Typical application
Figure 3.
Typical application circuit
VOUT
Load
VIN
IN
OUT
1 µF
1 µF
EN
GND
VEN
5/16
Maximum ratings
LD39015xx
4
Maximum ratings
Table 3.
Absolute maximum ratings
Parameter
Symbol
Value
Unit
VIN
VOUT
VEN
IOUT
PD
DC input voltage
-0.3 to 7
V
V
DC output voltage
- 0.3 to VI + 0.3
- 0.3 to VI + 0.3
Internally limited
Internally limited
-65 to 150
Enable input voltage
Output current
V
mA
mW
°C
°C
Power dissipation
TSTG
TOP
Storage temperature range
Operating junction temperature range
-40 to 125
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied. All values are referred to GND.
Table 4.
Symbol
Thermal data
Parameter
SOT23-5L
SOT666
Unit
RthJA
RthJC
Thermal resistance junction-ambient
Thermal resistance junction-case
255
81
132
56
°C/W
°C/W
6/16
LD39015xx
Electrical characteristics
5
Electrical characteristics
T = 25 °C, V = V
+ 1 V, C = C
= 1 µF, I
= 1 mA, V = V , unless
J
IN
OUT(NOM)
IN
OUT
OUT EN IN
otherwise specified.
(1)
Table 5.
Symbol
Electrical characteristics
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VIN
Operating input voltage
Turn-on threshold
1.5
5.5
V
V
1.45
1.35
1.48
VUVLO
Turn-off threshold
1.30
-2.0
mV
VOUT > 1.5V, IOUT = 1mA, TJ = 25°C
OUT > 1.5V, IOUT = 1mA,
2.0
3.0
%
V
-3.0
-40°C < TJ < 125°C
VOUT VOUT accuracy
VOUT ≤ 1.5V, IOUT = 1mA
10
30
mV
VOUT ≤ 1.5V, IOUT = 1mA,
-40°C < TJ < 125°C
ΔVOUT Static line regulation
VOUT +1V ≤ VIN ≤ 5.5V, IOUT = 1mA
0.01
10
%/V
ΔVIN = +500mV, IOUT = 1mA,
TR = TF = 5µs
ΔVOUT Transient line regulation (2)
mVpp
ΔVOUT Static load regulation
ΔVOUT Transient load regulation (2)
IOUT = 1mA to 150mA
0.002
40
%/mA
mVpp
IOUT = 1mA to 150mA, TR = TF = 5µs
IOUT = 100mA, VOUT > 1.5V
-40°C < TJ < 125°C
VDROP Dropout voltage (3)
80
29
100
mV
1.1kHz to 100kHz, IOUT = 10mA,
VOUT = 0.8V
eN
Output noise voltage
µVRMS
VIN = VOUTNOM + 0.5V +/-VRIPPLE
VRIPPLE = 0.1V, Freq. = 1kHz
IOUT = 10mA
65
Supply voltage rejection
SVR
dB
µA
VOUT = 1.5V
VIN = VOUTNOM + 0.5V +/-VRIPPLE
VRIPPLE = 0.1V, Freq.=10kHz
IOUT = 10mA
62
18
IOUT = 0mA
I
OUT = 0mA, -40°C < TJ < 125°C
50
IOUT = 0 to 150mA
38
IQ
Quiescent current
IOUT = 0 to 150mA
-40°C < TJ< 125°C
70
1
VIN input current in OFF MODE:
VEN = GND
0.001
350
ISC
Short circuit current
RL = 0
mA
V
VIN = 1.5V to 5.5V,
-40°C < TJ < 125°C
Enable input logic low
0.4
VEN
VIN = 1.5V to 5.5V,
Enable input logic high
0.9
V
-40°C < TJ < 125°C
7/16
Electrical characteristics
LD39015xx
(1)
Table 5.
Symbol
Electrical characteristics (continued)
Parameter
Test conditions
Min.
Typ.
Max.
100
Unit
IEN
Enable pin input current
Turn on time (4)
VEN = VIN
0.1
30
nA
µs
TON
Thermal shutdown
Hysteresis
160
20
TSHDN
°C
µF
Capacitance (see typical
performance characteristics for
stability)
COUT Output capacitor
1
22
1. For VOUT(NOM) < 1.2 V, VIN = 1.5 V
2. All transient values are guaranteed by design, not production tested
3. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply for output voltages below 1.5 V
4. Turn-on time is the time measured between the enable input just exceeding VEN High Value and the output voltage just
reaching 95 % of its nominal value
8/16
LD39015xx
Typical performance characteristics
6
Typical performance characteristics
Figure 4.
Output voltage vs. temperature
Figure 5.
Output voltage vs. input voltage
0.85
0.84
0.83
0.82
0.81
0.8
0.79
0.78
0.77
0.76
0.75
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
IOUT=1mA
IOUT=100mA
VIN=1.5V
VIN=1.5V
0
1
2
3
4
5
6
-50
0
50
100
150
VIN [V]
Temp [°C]
Figure 6.
Dropout voltage vs. output current Figure 7.
C
stability region
OUT
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
CIN=1 µF, VIN=VEN=1.5 to 5.5 V IOUT=1 mA to 0.15 A
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
STABILITY REGION
0
0
0.05
0.1
0.15
0.2
0.25
0
5
10
15
20
25
IOUT [A]
C
OUT [µF] (nominal value)
Figure 8.
Supply voltage rejection vs.
frequency
Figure 9.
Output noise voltage vs. frequency
800
700
600
500
400
300
200
100
0
75
70
65
60
55
50
45
40
35
30
25
20
15
10
IOUT=10 mA, VIN=4.3 V, CIN=COUT= 1µF
VOUT=3.3 V
IOUT = 10mA Vripple = 0.1Vpp
100
1000
10000
Freq [Hz]
100000
1000
10000
100000
FREQ [Hz]
9/16
Typical performance characteristics
LD39015xx
Figure 10. Quiescent current vs. input voltage Figure 11. Load transient
100
80
60
40
20
VIN=VINH, CIN=COUT=1µF, IOUT=0.15A
0
1.4 1.9 2.4 2.9 3.4 3.9 4.4 4.9 5.4 5.9
VIN[V]
VEN = VIN = 1.5V, IOUT = 1mA to 0.15A, CIN = COUT = 1µF,
tr = tf = 5µs
Figure 12. Line transient
Figure 13. Enable transient
VIN = 1.5V, VEN = 0 to 1V, IOUT = 1mA, CIN = COUT = 1µF
VIN = VEN = 1.5 to 5.5V, IOUT = 1mA, COUT = 1µF,
tr = tf = 5µs
10/16
LD39015xx
Package mechanical data
7
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com. ECOPACK
is an ST trademark.
11/16
Package mechanical data
LD39015xx
SOT23-5L mechanical data
mm.
mils.
Dim.
Min.
Typ.
Max.
1.45
0.10
1.30
0.50
0.20
3.00
1.75
Min.
35.4
0.0
Typ.
Max.
57.1
3.9
A
A1
A2
b
0.90
0.00
0.90
0.35
0.09
2.80
1.50
35.4
13.7
3.5
51.2
19.7
7.8
C
D
E
110.2
59.0
118.1
68.8
e
0.95
37.4
H
L
2.60
0.10
3.00
102.3
3.9
118.1
23.6
0.60
7049676D
12/16
LD39015xx
Package mechanical data
SOT666 mechanical data
mm.
inch.
Dim.
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A3
D
0.53
0.13
1.50
1.50
1.10
0.11
0.10
0.05
0.17
0.57
0.17
1.66
1.65
1.20
0.19
0.23
0.10
0.60
0.18
1.70
1.70
1.30
0.26
0.30
0.021
0.005
0.059
0.059
0.043
0.004
0.004
0.002
0.17
0.022
0.006
0.065
0.065
0.047
0.007
0.009
0.004
0.024
0.007
0.067
0.067
0.051
0.010
0.012
E
E1
L1
L2
L3
b
0.25
0.25
b1
e
0.27
0.50
0.34
0.27
0.5
0.34
e1
θ
0.20
0.2
8°
10°
12°
8°
10°
12°
7673701C
13/16
Package mechanical data
LD39015xx
Tape & reel SOT23-xL mechanical data
mm.
Typ.
inch.
Typ.
Dim.
Min.
Max.
180
Min.
Max.
7.086
0.519
A
C
12.8
20.2
60
13.0
13.2
0.504
0.795
2.362
0.512
D
N
T
14.4
3.33
3.27
1.47
4.1
0.567
0.131
0.128
0.0.58
0.161
0.161
Ao
Bo
Ko
Po
P
3.13
3.07
1.27
3.9
3.23
3.17
1.37
4.0
0.123
0.120
0.050
0.153
0.153
0.127
0.124
0.054
0.157
0.157
3.9
4.0
4.1
14/16
LD39015xx
Revision history
8
Revision history
Table 6.
Date
Document revision history
Revision
Changes
13-Nov-2007
1
2
3
Initial release.
11-Apr-2008
12-Feb-2009
Modified: Table 5 on page 7.
Modified: Table 1 on page 1.
15/16
LD39015xx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
16/16
相关型号:
©2020 ICPDF网 联系我们和版权申明