M34E02-FMB1TPM34E02-FMB1TP [STMICROELECTRONICS]
256X8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3 X 2 MM, ROHS COMPLIANT, UFDFP-8;型号: | M34E02-FMB1TPM34E02-FMB1TP |
厂家: | ST |
描述: | 256X8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3 X 2 MM, ROHS COMPLIANT, UFDFP-8 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 时钟 光电二极管 内存集成电路 |
文件: | 总34页 (文件大小:369K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
M34E02
M34E02-F
2 Kbit serial presence detect (SPD) EEPROM
for double data rate (DDR1 and DDR2) DRAM modules
Features
■ 2 Kbit EEPROM for DDR1 and DDR2 serial
presence detect
■ Backward compatible with the M34C02
■ Permanent and reversible software data
protection for lower 128 bytes
2
UFDFPN8 (MB or MC)
2 x 3 mm
■ 100 kHz and 400 kHz I C bus serial interface
■ Single supply voltage:
– 1.7 V to 5.5 V
■ Byte and Page Write (up to 16 bytes)
■ Self-timed write cycle
■ Noise filtering
– Schmitt trigger on bus inputs
– Noise filter on bus inputs
TSSOP8 (DW)
4.4 × 3 mm
■ Enhanced ESD/latch-up protection
■ More than 1 million erase/write cycles
■ More than 40 years’ data retention
®
■ ECOPACK (RoHS compliant) packages
■ Packages:
®
–
ECOPACK2 (RoHS-compliant and
Halogen-free)
May 2011
Doc ID 10367 Rev 11
1/34
www.st.com
1
Contents
M34E02, M34E02-F
Contents
1
2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1
2.2
2.3
2.4
2.5
Serial Clock (SCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Data (SDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chip Enable (E0, E1, E2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Write Control (WC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5.1
2.5.2
2.5.3
2.5.4
Operating supply voltage V
CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power-down conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
Device operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1
3.2
3.3
3.4
3.5
3.6
Start condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Stop condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Acknowledge bit (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Memory addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the write-protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.6.1
3.6.2
SWP and CWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PSWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.7
3.8
Write operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.7.1
3.7.2
3.7.3
Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Minimizing system delays by polling on ACK . . . . . . . . . . . . . . . . . . . . . 16
Read operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.8.1
3.8.2
3.8.3
3.8.4
Random Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Current Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Sequential Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Acknowledge in Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4
Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Contents
5
Use within a DDR1/DDR2 DRAM module . . . . . . . . . . . . . . . . . . . . . . . 18
5.1
Programming the M34E02 and M34E02-F . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1.1
5.1.2
Isolated DRAM module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DRAM module inserted in the application motherboard . . . . . . . . . . . . 19
6
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7
8
9
10
Doc ID 10367 Rev 11
3/34
List of tables
M34E02, M34E02-F
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Device select code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DRAM DIMM connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Acknowledge when writing data or defining the write-protection
(instructions with R/W bit = 0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Acknowledge when reading the write protection (instructions with R/W bit = 1). . . . . . . . . 20
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operating conditions (for temperature range 1 devices) . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operating conditions (for temperature range 6 devices) . . . . . . . . . . . . . . . . . . . . . . . . . . 23
AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Input parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DC characteristics (for temperature range 1 devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DC characteristics (for temperature range 6 devices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
AC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
2 x 3 mm, data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TSSOP8 – 8-lead thin shrink small outline, package mechanical data. . . . . . . . . . . . . . . . 30
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 16.
Table 17.
Table 18.
4/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TSSOP and MLP connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Device select code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2
Maximum R value versus bus parasitic capacitance (C) for an I C bus. . . . . . . . . . . . . . . 9
P
2
I C bus protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Result of setting the write protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the write protection (WC = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Write mode sequences in a non write-protected area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Write cycle polling flowchart using ACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 10. Read mode sequences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 11. Serial presence detect block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 12. AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13. AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 14. UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 15. TSSOP8 – 8-lead thin shrink small outline, package outline . . . . . . . . . . . . . . . . . . . . . . . 30
Doc ID 10367 Rev 11
5/34
Description
M34E02, M34E02-F
1
Description
The M34E02 and M34E02-F are 2 Kbit serial EEPROM memories able to lock permanently
the data in its first half (from location 00h to 7Fh). This facility has been designed specifically
for use in DRAM DIMMs (dual interline memory modules) with serial presence detect (SPD).
All the information concerning the DDR1 or DDR2 configuration of the DRAM module (such
as its access speed, size and organization) can be kept write-protected in the first half of the
memory.
The first half of the memory area can be write-protected using two different software write
protection mechanisms. By sending the device a specific sequence, the first 128 bytes of
the memory become write protected: permanently or resettable. In addition, the devices
allow the entire memory area to be write protected, using the WC input (for example by
tieing this input to V ).
CC
2
These I C-compatible electrically erasable programmable memory (EEPROM) devices are
organized as 256 × 8 bits.
2
I C uses a two wire serial interface, comprising a bi-directional data line and a clock line.
The devices carry a built-in 4-bit device type identifier code (1010) in accordance with the
2
I C bus definition to access the memory area and a second device type identifier code
(0110) to define the protection. These codes are used together with the voltage level applied
on the three chip enable inputs (E2, E1, E0).
2
The devices behave as a slave device in the I C protocol, with all memory operations
synchronized by the serial clock. Read and Write operations are initiated by a Start
condition, generated by the bus master. The Start condition is followed by a device select
code and RW bit (as described in the Device select code table), terminated by an
acknowledge bit.
th
When writing data to the memory, the memory inserts an acknowledge bit during the 9 bit
time, following the bus master’s 8-bit transmission. When data is read by the bus master, the
bus master acknowledges the receipt of the data byte in the same way. Data transfers are
terminated by a Stop condition after an Ack for WRITE, and after a NoAck for READ.
Figure 1.
Logic diagram
6
##
ꢃ
%ꢀꢄ%ꢂ
3$!
-ꢃꢅ%ꢀꢂ
-ꢃꢅ%ꢀꢂꢄ&
3#,
7#
6
33
!)ꢀꢁꢀꢂꢀB
6/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Figure 2.
Description
TSSOP and MLP connections (top view)
-ꢃꢅ%ꢀꢂꢇ -ꢃꢅ%ꢀꢂꢄ&
%ꢀ
%ꢆ
%ꢂ
ꢆ
ꢂ
ꢃ
ꢅ
ꢈ
ꢉ
ꢊ
ꢋ
6
##
7#
3#,
3$!
6
33
!)ꢀꢁꢀꢂꢆB
1. See the Package mechanical data section for package dimensions, and how to identify pin-1.
Table 1.
Signal names
Signal names
Description
E0, E1, E2
SDA
Chip Enable
Serial Data
Serial Clock
Write Control
Supply voltage
Ground
SCL
WC
VCC
VSS
Doc ID 10367 Rev 11
7/34
Signal description
M34E02, M34E02-F
2
Signal description
2.1
Serial Clock (SCL)
This input signal is used to strobe all data in and out of the device. In applications where this
signal is used by slave devices to synchronize the bus to a slower clock, the bus master
must have an open drain output, and a pull-up resistor can be connected from Serial Clock
(SCL) to V . (Figure 4 indicates how the value of the pull-up resistor can be calculated). In
CC
most applications, though, this method of synchronization is not employed, and so the pull-
up resistor is not necessary, provided that the bus master has a push-pull (rather than open
drain) output.
2.2
2.3
Serial Data (SDA)
This bidirectional signal is used to transfer data in or out of the device. It is an open drain
output that may be wire-OR’ed with other open drain or open collector signals on the bus. A
pull up resistor must be connected from Serial Data (SDA) to V . (Figure 4 indicates how
CC
the value of the pull-up resistor can be calculated).
Chip Enable (E0, E1, E2)
These input signals are used to set the value that is to be looked for on the three least
significant bits (b3, b2, b1) of the 7-bit device select code. In the end application, E0, E1 and
E2 must be directly (not through a pull-up or pull-down resistor) connected to V or V to
CC
SS
establish the device select code. When these inputs are not connected, an internal pull-
down circuitry makes (E0,E1,E2) = (0,0,0).
The E0 input is used to detect the V voltage, when decoding an SWP or CWP instruction.
HV
Figure 3.
Device select code
6
6
##
##
-ꢃꢅ%ꢀꢂ
-ꢃꢅ%ꢀꢂ
-ꢃꢅ%ꢀꢂꢄ&
-ꢃꢅ%ꢀꢂꢄ&
%
I
%
I
6
6
33
33
!IꢆꢂꢃꢀꢆB
2.4
Write Control (WC)
This input signal is provided for protecting the contents of the whole memory from
inadvertent write operations. Write Control (WC) is used to enable (when driven low) or
disable (when driven high) write instructions to the entire memory area or to the Protection
Register.
When Write Control (WC) is tied low or left unconnected, the write protection of the first half
of the memory is determined by the status of the Protection Register.
8/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Signal description
2.5
Supply voltage (VCC)
2.5.1
Operating supply voltage V
CC
Prior to selecting the memory and issuing instructions to it, a valid and stable V voltage
CC
within the specified [V (min), V (max)] range must be applied (see Table 8). In order to
CC
CC
secure a stable DC supply voltage, it is recommended to decouple the V line with a
CC
suitable capacitor (usually of the order of 10 nF to 100 nF) close to the V /V package
CC SS
pins.
This voltage must remain stable and valid until the end of the transmission of the instruction
and, for a Write instruction, until the completion of the internal write cycle (t ).
W
2.5.2
2.5.3
Power-up conditions
The V voltage has to rise continuously from 0 V up to the minimum V operating voltage
CC
CC
defined in Table 8 and the rise time must not vary faster than 1 V/µs.
Device reset
In order to prevent inadvertent write operations during power-up, a power-on reset (POR)
circuit is included. At power-up, the device does not respond to any instruction until V
CC
reaches the internal reset threshold voltage (this threshold is lower than the minimum V
CC
operating voltage defined in Table 8).
When V passes over the POR threshold, the device is reset and enters the Standby
CC
Power mode. However, the device must not be accessed until V reaches a valid and
CC
stable V voltage within the specified [V (min), V (max)] range.
CC
CC
CC
In a similar way, during power-down (continuous decrease in V ), as soon as V drops
CC
CC
below the power-on reset threshold voltage, the device stops responding to any instruction
sent to it.
2.5.4
Power-down conditions
During power-down (continuous decrease in V ), the device must be in Standby Power
CC
mode (mode reached after decoding a Stop condition, assuming that there is no internal
write cycle in progress).
2
Figure 4.
Maximum R value versus bus parasitic capacitance (C) for an I C bus
P
100
When t
LOW
= 1.3 µs (min value for
× C
f
= 400 kHz), the R
C
bus
bus
V
CC
time constant must be below the
400 ns time constant line
represented on the left.
10
R
bus
Here R
bus
× C = 120 ns
bus
4 kΩ
SCL
SDA
I²C bus
master
M24xxx
1
30 pF
C
bus
10
100
Bus line capacitor (pF)
1000
ai14796b
Doc ID 10367 Rev 11
9/34
Signal description
Figure 5.
M34E02, M34E02-F
2
I C bus protocol
SCL
SDA
SDA
Input
SDA
Change
Start
condition
Stop
condition
1
2
3
7
8
9
SCL
SDA
ACK
MSB
Start
condition
1
2
3
7
8
9
SCL
SDA
MSB
ACK
Stop
condition
AI00792c
Table 2.
Device select code
Device type identifier Chip Enable bits RW
Chip Enable
signals
b7(1) b6
b5
b4
b3
b2
b1
b0
Memory area select
code (two arrays)(2)
E2
E1
E0
1
0
1
0
E2
E1
E0 RW
Set write protection
(SWP)
(3)
VSS VSS VHV
0
0
0
1
1
1
0
0
0
Clear write protection
(CWP)
(3)
VSS VCC VHV
E2 E1 E0
Permanently set write
protection (PSWP)(2)
0
1
1
0
E2
E1
E0
(3)
Read SWP
VSS VSS VHV
VSS VCC VHV
0
0
0
1
1
1
1
1
1
(3)
Read CWP
Read PSWP(2)
E2
E1
E0
E2
E1
E0
1. The most significant bit, b7, is sent first.
2. E0, E1 and E2 are compared against the respective external pins on the memory device.
3. VHV is defined in Table 13.
10/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Device operation
3
Device operation
2
The device supports the I C protocol. This is summarized in Figure 5 Any device that sends
data on to the bus is defined to be a transmitter, and any device that reads the data to be a
receiver. The device that controls the data transfer is known as the bus master, and the
other as the slave device. A data transfer can only be initiated by the bus master, which will
also provide the serial clock for synchronization. The memory device is always a slave in all
communication.
3.1
3.2
Start condition
Start is identified by a falling edge of Serial Data (SDA) while Serial Clock (SCL) is stable in
the high state. A Start condition must precede any data transfer command. The device
continuously monitors (except during a Write cycle) Serial Data (SDA) and Serial Clock
(SCL) for a Start condition.
Stop condition
Stop is identified by a rising edge of Serial Data (SDA) while Serial Clock (SCL) is stable
and driven high. A Stop condition terminates communication between the device and the
bus master. A Read command that is followed by NoAck can be followed by a Stop condition
to force the device into the Standby mode. A Stop condition at the end of a Write command
triggers the internal EEPROM Write cycle.
3.3
3.4
Acknowledge bit (ACK)
The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter,
whether it be bus master or slave device, releases Serial Data (SDA) after sending eight bits
th
of data. During the 9 clock pulse period, the receiver pulls Serial Data (SDA) low to
acknowledge the receipt of the eight data bits.
Data input
During data input, the device samples Serial Data (SDA) on the rising edge of Serial Clock
(SCL). For correct device operation, Serial Data (SDA) must be stable during the rising edge
of Serial Clock (SCL), and the Serial Data (SDA) signal must change only when Serial Clock
(SCL) is driven low.
Doc ID 10367 Rev 11
11/34
Device operation
M34E02, M34E02-F
3.5
Memory addressing
To start communication between the bus master and the slave device, the bus master must
initiate a Start condition. Following this, the bus master sends the device select code, shown
in Table 2 (on Serial Data (SDA), most significant bit first).
The device select code consists of a 4-bit device type identifier, and a 3-bit Chip Enable
“Address” (E2, E1, E0). To address the memory array, the 4-bit device type identifier is
1010b; to access the write-protection settings, it is 0110b.
2
Up to eight memory devices can be connected on a single I C bus. Each one is given a
unique 3-bit code on the Chip Enable (E0, E1, E2) inputs. When the device select code is
received, the device only responds if the Chip Enable address is the same as the value on
the Chip Enable (E0, E1, E2) inputs.
th
The 8 bit is the Read/Write bit (RW). This bit is set to 1 for Read and 0 for Write operations.
If a match occurs on the device select code, the corresponding device gives an
th
acknowledgment on Serial Data (SDA) during the 9 bit time. If the device does not match
the device select code, it deselects itself from the bus, and goes into Standby mode.
Table 3.
Operating modes
Mode
RW bit
WC(1)
Bytes
Initial Sequence
Current Address Read
Random Address Read
1
0
1
X
X
X
1
Start, Device Select, RW = 1
Start, Device Select, RW = 0, Address
reStart, Device Select, RW = 1
1
Similar to Current or Random Address
Read
Sequential Read
1
X
≥ 1
Byte Write
Page Write
0
0
VIL
VIL
1
Start, Device Select, RW = 0
Start, Device Select, RW = 0
≤16
1. X = V or V .
IH
IL
Figure 6.
Result of setting the write protection
FFh
Standard
FFh
Standard
Array
Array
Memory
80h
80h
7Fh
Area
7Fh
Write
Protected
Array
Standard
Array
00h
00h
Default EEPROM memory area
state before write access
to the Protect Register
State of the EEPROM memory
area after write access
to the Protect Register
AI01936C
12/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Device operation
3.6
Setting the write-protection
The M34E02 and M34E02-F have a hardware write-protection feature, using the Write
Control (WC) signal. This signal can be driven high or low, and must be held constant for the
whole instruction sequence. When Write Control (WC) is held high, the whole memory array
(addresses 00h to FFh) is write protected. When Write Control (WC) is held low, the write
protection of the memory array is dependent on whether software write-protection has been
set.
Software write-protection allows the bottom half of the memory area (addresses 00h to 7Fh)
to be write protected irrespective of subsequent states of the Write Control (WC) signal.
Software write-protection is handled by three instructions:
●
●
●
SWP: Set Write Protection
CWP: Clear Write Protection
PSWP: Permanently Set Write Protection
The level of write-protection (set or cleared) that has been defined using these instructions,
remains defined even after a power cycle.
3.6.1
SWP and CWP
If the software write-protection has been set with the SWP instruction, it can be cleared
again with a CWP instruction.
The two instructions (SWP and CWP) have the same format as a Byte Write instruction, but
with a different device type identifier (as shown in Table 2). Like the Byte Write instruction, it
is followed by an address byte and a data byte, but in this case the contents are all “Don’t
Care” (Figure 7). Another difference is that the voltage, V , must be applied on the E0 pin,
HV
and specific logical levels must be applied on the other two (E1 and E2, as shown in
Table 2).
3.6.2
PSWP
If the software write-protection has been set with the PSWP instruction, the first 128 bytes of
the memory are permanently write-protected. This write-protection cannot be cleared by
any instruction, or by power-cycling the device, and regardless the state of Write Control
(WC). Also, once the PSWP instruction has been successfully executed, the M34E02 and
M34E02-F no longer acknowledge any instruction (with a device type identifier of 0110) to
access the write-protection settings.
Figure 7.
Setting the write protection (WC = 0)
BUS ACTIVITY
MASTER
CONTROL
BYTE
WORD
ADDRESS
DATA
SDA LINE
BUS ACTIVITY
ACK
ACK
ACK
VALUE
VALUE
(DON'T CARE) (DON'T CARE)
AI01935B
Doc ID 10367 Rev 11
13/34
Device operation
M34E02, M34E02-F
3.7
Write operations
Following a Start condition the bus master sends a device select code with the RW bit reset
to 0. The device acknowledges this, as shown in Figure 8, and waits for an address byte.
The device responds to the address byte with an acknowledge bit, and then waits for the
data byte.
When the bus master generates a Stop condition immediately after a data byte Ack bit (in
th
the “10 bit” time slot), either at the end of a Byte Write or a Page Write, the internal
memory Write cycle is triggered. A Stop condition at any other time slot does not trigger the
internal Write cycle.
During the internal Write cycle, Serial Data (SDA) and Serial Clock (SCL) are ignored, and
the device does not respond to any requests.
3.7.1
3.7.2
Byte Write
After the device select code and the address byte, the bus master sends one data byte. If
the addressed location is hardware write-protected, the device replies to the data byte with
NoAck, and the location is not modified. If, instead, the addressed location is not Write-
protected, the device replies with Ack. The bus master terminates the transfer by generating
a Stop condition, as shown in Figure 8
Page Write
The Page Write mode allows up to 16 bytes to be written in a single Write cycle, provided
that they are all located in the same page in the memory: that is, the most significant
memory address bits are the same. If more bytes are sent than will fit up to the end of the
page, a condition known as ‘roll-over’ occurs. This should be avoided, as data starts to
become overwritten in an implementation dependent way.
The bus master sends from 1 to 16 bytes of data, each of which is acknowledged by the
device if Write Control (WC) is low. If the addressed location is hardware write-protected,
the device replies to the data byte with NoAck, and the locations are not modified. After each
byte is transferred, the internal byte address counter (the 4 least significant address bits
only) is incremented. The transfer is terminated by the bus master generating a Stop
condition.
14/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Figure 8.
Device operation
Write mode sequences in a non write-protected area
ACK
ACK
ACK
Byte Write
Device select
Byte address
Data in
R/W
ACK
Byte address
ACK
ACK
Page Write
Device select
Data in 1
Data in 2
R/W
ACK
ACK
Data in N
AI01941b
Figure 9.
Write cycle polling flowchart using ACK
WRITE cycle
in progress
Start condition
Device select
with RW = 0
ACK
NO
returned
First byte of instruction
with RW = 0 already
decoded by the device
YES
Next
operation is
addressing the
memory
NO
YES
Send address
and receive ACK
ReStart
Start
NO
YES
Stop
condition
Data for the
WRITE operation
Device select
with RW = 1
Continue the
Continue the
Random READ operation
WRITE operation
AI01847d
Doc ID 10367 Rev 11
15/34
Device operation
M34E02, M34E02-F
3.7.3
Minimizing system delays by polling on ACK
During the internal Write cycle, the device disconnects itself from the bus, and writes a copy
of the data from its internal latches to the memory cells. The maximum Write time (tw) is
shown in Table 14, but the typical time is shorter. To make use of this, a polling sequence
can be used by the bus master.
The sequence, as shown in Figure 9, is:
●
Initial condition: a Write cycle is in progress.
●
Step 1: the bus master issues a Start condition followed by a device select code (the
first byte of the new instruction).
●
Step 2: if the device is busy with the internal Write cycle, no Ack will be returned and
the bus master goes back to Step 1. If the device has terminated the internal Write
cycle, it responds with an Ack, indicating that the device is ready to receive the second
part of the instruction (the first byte of this instruction having been sent during Step 1).
3.8
Read operations
Read operations are performed independently of whether hardware or software protection
has been set.
The device has an internal address counter which is incremented each time a byte is read.
3.8.1
Random Address Read
A dummy Write is first performed to load the address into this address counter (as shown in
Figure 10) but without sending a Stop condition. Then, the bus master sends another Start
condition, and repeats the device select code, with the RW bit set to 1. The device
acknowledges this, and outputs the contents of the addressed byte. The bus master must
not acknowledge the byte, and terminates the transfer with a Stop condition.
3.8.2
3.8.3
Current Address Read
For the Current Address Read operation, following a Start condition, the bus master only
sends a device select code with the RW bit set to 1. The device acknowledges this, and
outputs the byte addressed by the internal address counter. The counter is then
incremented. The bus master terminates the transfer with a Stop condition, as shown in
Figure 10, without acknowledging the byte.
Sequential Read
This operation can be used after a Current Address Read or a Random Address Read. The
bus master does acknowledge the data byte output, and sends additional clock pulses so
that the device continues to output the next byte in sequence. To terminate the stream of
bytes, the bus master must not acknowledge the last byte, and must generate a Stop
condition, as shown in Figure 10.
The output data comes from consecutive addresses, with the internal address counter
automatically incremented after each byte output. After the last memory address, the
address counter ‘rolls-over’, and the device continues to output data from memory address
00h.
16/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Device operation
3.8.4
Acknowledge in Read mode
For all Read commands, the device waits, after each byte read, for an acknowledgment
th
during the 9 bit time. If the bus master does not drive Serial Data (SDA) low during this
time, the device terminates the data transfer and switches to its Standby mode.
Figure 10. Read mode sequences
ACK
NO ACK
Current
Address
Read
Dev select
Data out
R/W
ACK
ACK
ACK
NO ACK
Random
Address
Read
Dev select *
Byte address
Dev select *
Data out
R/W
R/W
ACK
ACK
ACK
NO ACK
Data out N
Sequential
Current
Read
Dev select
Data out 1
R/W
ACK
ACK
ACK
R/W
ACK
Sequential
Random
Read
Dev select *
Byte address
Dev select *
Data out 1
R/W
ACK
NO ACK
Data out N
AI01942b
1. The seven most significant bits of the device select code of a Random Read (in the 1st and 3rd bytes) must
be identical.
Doc ID 10367 Rev 11
17/34
Initial delivery state
M34E02, M34E02-F
4
Initial delivery state
The device is delivered with all bits in the memory array set to ‘1’ (each Byte contains FFh).
5
Use within a DDR1/DDR2 DRAM module
In the application, the M34E02/M34E02-F is soldered directly in the printed circuit module.
The three Chip Enable inputs (E0, E1, E2) must be connected to V or V directly (that is
SS
CC
without using a pull-up or pull-down resistor) through the DIMM socket (see Table 4). The
2
2
pull-up resistors needed for normal behavior of the I C bus are connected on the I C bus of
the mother-board (as shown in Figure 11).
The Write Control (WC) of the M34E02/M34E02-F can be left unconnected. However,
connecting it to V is recommended, to maintain full read and write access.
SS
Table 4.
DRAM DIMM connections
DIMM position E2
E1
E0
0
1
2
3
4
5
6
7
VSS
VSS
VSS
VSS
VCC
VCC
VCC
VCC
VSS
VSS
VCC
VCC
VSS
VSS
VCC
VCC
VSS
VCC
VSS
VCC
VSS
VCC
VSS
VCC
5.1
Programming the M34E02 and M34E02-F
The situations in which the M34E02 and M34E02-F are programmed can be considered
under two headings:
●
when the DDR2 DRAM is isolated (not inserted on the PCB motherboard)
when the DDR2 DRAM is inserted on the PCB motherboard
●
5.1.1
Isolated DRAM module
With specific programming equipment, it is possible to define the M34E02/M34E02-F
content, using Byte and Page Write instructions, and its write-protection using the SWP and
CWP instructions. To issue the SWP and CWP instructions, the DRAM module must be
inserted in a specific slot where the E0 signal can be driven to V during the whole
HV
instruction. This programming step is mainly intended for use by DRAM module makers,
whose end application manufacturers will want to clear this write-protection with the CWP
on their own specific programming equipment, to modify the lower 128 Bytes, and finally to
set permanently the write-protection with the PSWP instruction.
18/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Use within a DDR1/DDR2 DRAM module
5.1.2
DRAM module inserted in the application motherboard
As the final application cannot drive the E0 pin to V , the only possible action is to freeze
HV
the write-protection with the PSWP instruction.
Table 5 and Table 6 show how the Ack bits can be used to identify the write-protection
status.
Table 5.
Status
Acknowledge when writing data or defining the write-protection
(instructions with R/W bit = 0)
WC
Write
cycle
(tW)
input
level
Instruction
Ack
Address
Ack Data byte Ack
PSWP, SWP or
CWP
Not
significant
Not
significant
NoAck
Ack
NoAck
Ack
NoAck
NoAck
NoAck
Ack
No
No
No
Yes
Yes
No
No
No
Permanently
protected
X
Page or Byte Write
in lower 128 bytes
Address
Data
Not
significant
Not
significant
SWP
CWP
NoAck
Ack
NoAck
Ack
Not
significant
Not
significant
Not
significant
Not
significant
0
1
PSWP
Ack
Ack
Ack
Page or Byte Write
in lower 128 bytes
Ack
Address
Ack
Data
NoAck
NoAck
NoAck
Protected
with SWP
Not
significant
Not
significant
SWP
CWP
NoAck
Ack
NoAck
Ack
Not
significant
Not
significant
Not
significant
Not
significant
PSWP
Ack
Ack
Ack
Ack
Ack
Ack
Ack
Ack
Ack
Ack
Ack
Ack
NoAck
NoAck
Ack
No
No
Yes
Yes
No
No
Page or Byte Write
Address
Data
PSWP, SWP or
CWP
Not
significant
Not
significant
0
1
Page or Byte Write
Address
Data
Ack
Not
Protected
PSWP, SWP or
CWP
Not
significant
Not
significant
NoAck
NoAck
Page or Byte Write
Address
Data
Doc ID 10367 Rev 11
19/34
Use within a DDR1/DDR2 DRAM module
M34E02, M34E02-F
Table 6.
Status
Acknowledge when reading the write protection (instructions with R/W
bit = 1)
Instruction
Ack
Address
Ack
Data byte
Ack
Permanently
protected
PSWP, SWP or CWP NoAck Not significant NoAck Not significant NoAck
SWP
CWP
NoAck Not significant NoAck Not significant NoAck
Protected with
SWP
Ack
Ack
Ack
Not significant NoAck Not significant NoAck
Not significant NoAck Not significant NoAck
Not significant NoAck Not significant NoAck
PSWP
Not protected PSWP, SWP or CWP
20/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Use within a DDR1/DDR2 DRAM module
Figure 11. Serial presence detect block diagram
R = 4.7 kΩ
DRAM module slot number 7
E2
E1
E0 SCL SDA
V
CC
DRAM module slot number 6
E2
E1
E0 SCL SDA
V
V
SS
CC
DRAM module slot number 5
E2
E1
E0 SCL SDA
V
V
V
CC
CC
SS
DRAM module slot number 4
E2
E1
E0 SCL SDA
V
V
SS
CC
DRAM module slot number 3
E2
E1
E1
E0 SCL SDA
V
V
CC
SS
DRAM module slot number 2
E2
E0 SCL SDA
V
V
V
SS
SS
CC
DRAM module slot number 1
E2
E1
E0 SCL SDA
V
V
CC
SS
DRAM module slot number 0
E2
E1
E0 SCL SDA
V
SS
SCL line
SDA line
From the motherboard
I2C master controller
AI01937b
1. E0, E1 and E2 are wired at each DRAM module slot in a binary sequence for a maximum of 8 devices.
2. Common clock and common data are shared across all the devices.
Doc ID 10367 Rev 11
21/34
Maximum rating
M34E02, M34E02-F
6
Maximum rating
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 7.
Symbol
Absolute maximum ratings
Parameter
Min.
Max.
Unit
Ambient temperature with power applied
Storage temperature
–55
–65
130
150
°C
°C
TSTG
VIO
E0
–0.50
–0.50
10.0
6.5
Input or output range
V
Others
IOL
VCC
VESD
DC output current (SDA = 0)
Supply voltage
-
5
mA
V
–0.5
–4000
6.5
Electrostatic discharge voltage (human body model)(1)
4000
V
1. JEDEC Std JESD22-A114A (C1=100 pF, R1=1500 Ω, R2=500 Ω)
22/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
DC and AC parameters
7
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristic tables that
follow are derived from tests performed under the measurement conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 8.
Symbol
Operating conditions (for temperature range 1 devices)
Parameter
Min.
Max.
Unit
VCC
TA
Supply voltage
Ambient operating temperature
1.7
0
3.6
70
V
°C
Table 9.
Symbol
Operating conditions (for temperature range 6 devices)
Parameter
Min.
Max.
Unit
VCC
TA
Supply voltage
Ambient operating temperature
1.7
5.5
V
–40
+85
°C
Table 10. AC measurement conditions
Symbol
Parameter
Min.
Max.
Unit
CL
Load capacitance
100
pF
SCL input rise and fall time,
SDA input fall time
50
ns
Input levels
0.2VCC to 0.8VCC
0.3VCC to 0.7VCC
V
V
Input and output timing reference levels
Figure 12. AC measurement I/O waveform
Input Levels
Input and Output
Timing Reference Levels
0.8V
CC
0.7V
CC
0.3V
CC
0.2V
CC
AI00825B
Doc ID 10367 Rev 11
23/34
DC and AC parameters
M34E02, M34E02-F
Table 11. Input parameters
Symbol
Parameter(1)
Test condition
Min.
Max.
Unit
CIN
CIN
Input capacitance (SDA)
Input capacitance (other pins)
Ei (E0, E1, E2) input impedance
Ei (E0, E1, E2) input impedance
WC input impedance
8
6
pF
pF
kΩ
kΩ
kΩ
kΩ
ZEiL
VIN < 0.3VCC
VIN > 0.7VCC
VIN < 0.3VCC
VIN > 0.7VCC
30
800
5
ZEiH
ZWCL
ZWCH
WC input impedance
500
Pulse width ignored (input filter on
SCL and SDA)
tNS
100
ns
1. Characterized, not tested in production.
Table 12. DC characteristics (for temperature range 1 devices)
Test condition (in addition to
Symbol
Parameter
Min
Max
Unit
those in Table 8)
Input leakage current
(SCL, SDA)
ILI
VIN = VSS or VCC
2
2
µA
µA
SDA in Hi-Z, external voltage
applied on SDA: VSS or VCC
ILO
Output leakage current
Supply current (read)
VCC = 1.7 V, fc = 100 kHz
VCC = 3.6 V, fc = 100 kHz
1
2
mA
mA
ICC
ICC1
VIL
Device not selected(1)
VIN = VSS or VCC, VCC = 3.6 V
Device not selected(1)
,
2
1
µA
µA
Standby supply current
,
VIN = VSS or VCC, VCC = 1.7 V
2.5 ≤ VCC
–0.45 0.3 VCC
–0.45 0.25VCC
V
V
Input low voltage
(SCL, SDA, WC)
1.7 V ≤ VCC < 2.5 V
Input high voltage
(SCL, SDA, WC)
VIH
0.7VCC VCC+1
V
VHV
E0 high voltage
VHV – VCC ≥ 4.8 V
7
10
0.4
0.2
V
V
V
I
OL = 2.1 mA, 2.2 V ≤ VCC ≤ 3.6 V
VOL
Output low voltage
I
OL = 0.7 mA, VCC = 1.7 V
1. The device is not selected after a power-up, after a read command (after the Stop condition), or after the
completion of the internal write cycle tW (tW is triggered by the correct decoding of a write command).
24/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
DC and AC parameters
Table 13. DC characteristics (for temperature range 6 devices)
Test condition (in addition to
Symbol
Parameter
Min
Max
Unit
those in Table 9)
Input leakage current
(SCL, SDA)
ILI
V
IN = VSS or VCC
2
2
µA
µA
SDA in Hi-Z, external voltage
applied on SDA: VSS or VCC
ILO
Output leakage current
Supply current (read)
V
CC < 2.5 V, fc = 400 kHz
VCC ≥ 2.5 V, fc = 400 kHz
Device not selected(1)
VIN = VSS or VCC, VCC ≥ 2.5 V
Device not selected(1)
VIN = VSS or VCC, VCC < 2.5 V
1
3
mA
mA
ICC
ICC1
VIL
,
2
µA
µA
Standby supply current
,
1
2.5 ≤ VCC
–0.45
0.3 VCC
V
V
Input low voltage
(SCL, SDA, WC)
1.8 V ≤ VCC < 2.5 V
–0.45 0.25VCC
Input high voltage
(SCL, SDA, WC)
VIH
0.7VCC
7
VCC+1
V
VHV
E0 high voltage
VHV – VCC ≥ 4.8 V
10
0.4
0.4
0.2
V
V
V
V
IOL = 3.0 mA, VCC = 5.5 V
VOL
Output low voltage
I
OL = 2.1 mA, VCC = 2.5 V
IOL = 0.7 mA, VCC = 1.7 V
1. The device is not selected after a power-up, after a read command (after the Stop condition), or after the
completion of the internal write cycle tW (tW is triggered by the correct decoding of a write command).
Doc ID 10367 Rev 11
25/34
DC and AC parameters
M34E02, M34E02-F
Table 14. AC characteristics
Test conditions specified in Table 10, Table 8 and Table 9
Symbol
Alt.
Parameter
Min.
Max.
Unit
fC
fSCL
tHIGH
tLOW
tF
Clock frequency
400
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tCHCL
tCLCH
Clock pulse width high
Clock pulse width low
SDA (out) fall time
600
1300
20
(1)
tDL1DL2
100
300
300
(2)
tXH1XH2
tR
Input signal rise time
Input signal fall time
20
(2)
tXL1XL2
tF
20
tDXCX
tCLDX
tCLQX
tSU:DAT Data in set up time
tHD:DAT Data in hold time
100
0
tDH
tAA
Data out hold time
200
200
600
600
600
(3)(4)
tCLQV
Clock low to next data valid (access time)
900
(5)
tCHDL
tSU:STA Start condition setup time
tHD:STA Start condition hold time
tSU:STO Stop condition setup time
tDLCL
tCHDH
Time between Stop condition and next Start
condition
tDHDL
tW
tBUF
tWR
1300
ns
Write time
5
ms
1. Sampled only, not 100% tested.
2. Values recommended by I²C-bus/Fast-Mode specification.
3. To avoid spurious Start and Stop conditions, a minimum delay is placed between SCL=1 and the falling or
rising edge of SDA.
4. tCLQV is the time (from the falling edge of SCL) required by the SDA bus line to reach either 0.3VCC or
0.7VCC, assuming that the Rbus × Cbus time constant is within the values specified in Figure 4).
5. For a re-Start condition, or following a Write cycle.
26/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
DC and AC parameters
Figure 13. AC waveforms
tXL1XL2
tXH1XH2
tCHCL
tCLCH
SCL
tDLCL
tXL1XL2
SDA In
tCHDL
Start
condition
tCLDX
tDXCX
SDA
Change
tXH1XH2
tCHDH tDHDL
Start
SDA
Input
Stop
condition
condition
SCL
SDA In
tW
Write cycle
tCHDH
tCHDL
Stop
condition
Start
condition
tCHCL
SCL
tCLQV
tCLQX
Data valid
tDL1DL2
Data valid
SDA Out
AI00795f
Doc ID 10367 Rev 11
27/34
Package mechanical data
M34E02, M34E02-F
8
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
28/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Package mechanical data
Figure 14. UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, outline
E
B
E
B
$
-"
-#
,ꢆ
,ꢆ
,ꢃ
,ꢃ
0IN ꢆ
%ꢂ
+
%
%ꢂ
+
,
,
!
$ꢂ
$ꢂ
EEE
!ꢆ
:7?-%E
1. Drawing is not to scale.
2. The central pad (area E2 by D2 in the above illustration) is pulled, internally, to VSS. It must not be allowed
to be connected to any other voltage or signal line on the PCB, for example during the soldering process.
3. The circle in the top view of the package indicates the position of pin 1.
Table 15. UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat package no lead
2 x 3 mm, data
millimeters
Min
inches(1)
Symbol
Typ
Max
Typ
Min
Max
A
A1
0.550
0.020
0.250
2.000
1.600
0.450
0.000
0.200
1.900
1.500
1.200
2.900
0.100
1.200
0.600
0.050
0.300
2.100
1.700
1.600
3.100
0.300
1.600
0.0217
0.0008
0.0098
0.0787
0.0630
0.0177
0.0000
0.0079
0.0748
0.0591
0.0472
0.1142
0.0039
0.0472
0.0236
0.0020
0.0118
0.0827
0.0669
0.0630
0.1220
0.0118
0.0630
b
D
D2 (rev MB)
D2 (rev MC)
E
3.000
0.200
0.1181
0.0079
E2 (rev MB)
E2 (rev MC)
e
0.500
0.450
0.0197
0.0177
K (rev MB)
K (rev MC)
L (rev MB)
L (rev MC)
L1
0.800
0.300
0.400
0.300
0.0315
0.0118
0.0157
0.0118
0.500
0.500
0.150
0.0197
0.0197
0.0059
L3
0.300
0.080
0.0118
0.0031
eee(2)
1. Values in inches are converted from mm and rounded to 4 decimal digits.
2. Applied for exposed die paddle and terminals. Exclude embedding part of exposed die paddle from
measuring.
Doc ID 10367 Rev 11
29/34
Package mechanical data
M34E02, M34E02-F
Figure 15. TSSOP8 – 8-lead thin shrink small outline, package outline
D
8
5
c
E1
E
1
4
α
A1
L
A
A2
L1
CP
b
e
TSSOP8AM
1. Drawing is not to scale.
2. The circle around the number 1 in the top view of the package indicates the position of pin 1. The numbers
4, 5 and 8 indicate the positions of pins 4, 5 and 8, respectively.
Table 16. TSSOP8 – 8-lead thin shrink small outline, package mechanical data
millimeters
Min.
inches(1)
Symbol
Typ.
Max.
Typ.
Min.
Max.
A
A1
A2
b
1.200
0.150
1.050
0.300
0.200
0.100
3.100
–
0.0472
0.0059
0.0413
0.0118
0.0079
0.0039
0.1220
–
0.050
0.800
0.190
0.090
0.0020
0.0315
0.0075
0.0035
1.000
0.0394
c
CP
D
3.000
0.650
6.400
4.400
0.600
1.000
2.900
–
0.1181
0.0256
0.2520
0.1732
0.0236
0.0394
0.1142
–
e
E
6.200
4.300
0.450
6.600
4.500
0.750
0.2441
0.1693
0.0177
0.2598
0.1772
0.0295
E1
L
L1
α
0°
8
8°
0°
8
8°
N
1. Values in inches are converted from mm and rounded to 4 decimal digits.
30/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Part numbering
9
Part numbering
Table 17. Ordering information scheme
Example:
M34E02
–
F DW
1
T
P
Device type
M34 = ASSP I2C serial access EEPROM
Device function
E02 = 2 Kbit (256 × 8) SPD (serial presence detect) for DDR1 and DDR2
Operating voltage
F = VCC = 1.7 to 3.6 V over 0°C to 70 °C(1) or
F = VCC = 1.7 to 5.5 V over –40 °C to 85 °C(2)
Package
MB or MC= UDFDFPN8 (MLP8)
DW = TSSOP8 (4.4 × 3 mm body size)
Temperature range
1 = 0 to 70 °C
6 = –40 to 85 °C
Option
blank = Standard packing
T = Tape & reel packing
Plating technology
P or G = ECOPACK (RoHS compliant)
1. The 1.7 to 3.6 V operating voltage range is available only on temperature range 1 devices.
2. The 1.7 to 5.5 V operating voltage range is available only on temperature range 6 devices.
For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST sales office.
Doc ID 10367 Rev 11
31/34
Revision history
M34E02, M34E02-F
10
Revision history
Table 18. Document revision history
Date
Revision
Changes
13-Nov-2003
1.0
First release
TSSOP8 4.4x3 package replaces TSSOP8 3x3 (MSOP8) package.
Correction to sentence in “Setting the Write Protection”. Correction to
specification of tNS values.
01-Dec-2003
1.1
Always NoACK after Address and Data bytes in Table 6. Improvement in
VIO and VCC (min) in Absolute Maximum Ratings table. IOL changed for
test condition of VOL. MLP package mechanical data respecified.
Soldering temperature information clarified for RoHS compliant devices.
29-Mar-2004
14-Apr-2004
1.2
2.0
First public release
Direct connection of E0, E1, E2 to VSS and VCC (see Chip Enable (E0,
E1, E2) and Use within a DDR1/DDR2 DRAM module paragraphs). ZEiL
and ZEiH parameters added to Table 11: Input parameters. E0, E1, E2
removed from the Parameter descriptions of VIL and VIH in Table 13: DC
characteristics (for temperature range 6 devices).
24-Nov-2004
3.0
Document status promoted from Product Preview to full Datasheet.
Datasheet title changed. Features revised.
Plating Technology options updated in Table 17: Ordering information
scheme.
11-Mar-2005
28 -Apr-2005
4.0
5.0
Resistance and capacitance renamed in Figure 4: Maximum RP value
versus bus parasitic capacitance (C) for an I2C bus.
Text in Power On Reset changed. Noise filter value in Table 11: Input
parameters modified. ICC value 2mA, when Vcc=3/6V, added to Table 13:
DC characteristics (for temperature range 6 devices).
In Table 14: AC characteristics: Frequency fC changed from 100kHz to
400kHz, related AC timings (tCHCL, tCLCH, tDXCX, tCLQV max, tCHDX, tDLCL
tCHDH, tDHDL) also modified.
,
Power On Reset paragraph removed replaced by Internal device reset.
10-Apr-2006
6
Figure 3: Device select code inserted. ICC1 modified in Table 13: DC
characteristics (for temperature range 6 devices).
Note 3 added to Figure 14 and Note 2 added to Figure 15
All packages are ECOPACK® (see text added under Description and Part
numbering, TLEAD removed from Table 7: Absolute maximum ratings).
32/34
Doc ID 10367 Rev 11
M34E02, M34E02-F
Table 18. Document revision history (continued)
Revision history
Date
Revision
Changes
Datasheet title and Features on page 1 modified: the device can be used
with DDR1 and DDR2 DRAM configurations.
Temperature range 6 added, operating voltage range VCC extended in
device temperature range 6. IOL added to and TA modified in Table 7:
Absolute maximum ratings.
ILO, ICC and VIL modified in Table 13: DC characteristics (for temperature
range 6 devices). Table 14: AC characteristics added. Table 13: DC
characteristics (for temperature range 6 devices) modified. Figure 13: AC
waveforms modified.
18-Mar-2009
7
Figure 4: Maximum RP value versus bus parasitic capacitance (C) for an
I2C bus updated. Note removed below Figure 11: Serial presence detect
block diagram.
UFDFPN8 package specifications updated (see Table 15: UFDFPN8
(MLP8) 8-lead ultra thin fine pitch dual flat package no lead 2 x 3 mm,
data).
Blank option removed under plating technology in Table 17: Ordering
information scheme. Small text changes.
Section 2.5.2: Power-up conditions and Section 2.5.3: Device reset
updated. Figure 4: Maximum RP value versus bus parasitic capacitance
(C) for an I2C bus modified.
25-Sep-2009
01-Apr-2010
8
9
tNS modified in Table 11: Input parameters.
ICC and VIL test conditions extended in Table 12: DC characteristics (for
temperature range 1 devices).
Test condition updated in Table 12: DC characteristics (for temperature
range 1 devices) and Table 13: DC characteristics (for temperature range
6 devices)
Updated Figure 14: UFDFPN8 (MLP8) 8-lead ultra thin fine pitch dual flat
package no lead 2 x 3 mm, outline and Table 15: UFDFPN8 (MLP8) 8-
lead ultra thin fine pitch dual flat package no lead 2 x 3 mm, data
Added M34E02-F part number.
Added ambient temperature with power applied in Table 7: Absolute
maximum ratings.
Updated ICC1 conditions in Table 12: DC characteristics (for temperature
range 1 devices).
23-Jul-2010
10
11
Added Note 4 for tCLQV in Table 14: AC characteristics. Updated
Figure 13: AC waveforms.
tCHDX replaced by tCHDL in Figure 13: AC waveforms.
Modified MC package outline in Figure 14: UFDFPN8 (MLP8) 8-lead ultra
thin fine pitch dual flat package no lead 2 x 3 mm, outline.
27-May-2011
Updated MLP8 package data.
Doc ID 10367 Rev 11
33/34
M34E02, M34E02-F
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
34/34
Doc ID 10367 Rev 11
相关型号:
M34E02-FMB6G
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMB6GM34E02-FMB6G
256X8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3 X 2 MM, ROHS COMPLIANT, UFDFP-8
STMICROELECTR
M34E02-FMB6P
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMB6PM34E02-FMB6P
256X8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3 X 2 MM, ROHS COMPLIANT, UFDFP-8
STMICROELECTR
M34E02-FMB6TG
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMB6TGM34E02-FMB6TG
256X8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3 X 2 MM, ROHS COMPLIANT, UFDFP-8
STMICROELECTR
M34E02-FMB6TP
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMB6TPM34E02-FMB6TP
256X8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3 X 2 MM, ROHS COMPLIANT, UFDFP-8
STMICROELECTR
M34E02-FMC1G
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMC1P
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMC1TG
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
M34E02-FMC1TP
2 Kbit serial presence detect (SPD) EEPROM for double data rate (DDR1 and DDR2) DRAM modules
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明