M41T93SMY6F [STMICROELECTRONICS]
Serial SPI bus RTC with battery switchover; 串行SPI总线RTC，电池切换
| 型号： | M41T93SMY6F |
| 厂家： | 
ST |
| 描述： | Serial SPI bus RTC with battery switchover |
| 文件： | 总49页 (文件大小：418K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
M41T93
Serial SPI bus RTC with battery switchover
Preliminary Data
Feature summary
■ 2.0 to 5.5V clock operating voltage
■ Ultra-low battery supply current of 365nA
■ Counters for tenths/hundredths of seconds,
seconds, minutes, hours, day, date, month,
year, and century
QFN16, 4mm x 4mm (QA)
■ Programmable clock calibration (analog and
digital)
18
■ Automatic switch-over and reset output
1
circuitry (fixed reference)
– M41T93S: V = 3.0V to 5.5V
CC
SOX18 (MY, 18-pin, 300mil SOIC
with Embedded Crystal)
(2.85V ≤V
≤3.00V)
RST
– M41T93R: V = 2.7V to 5.5V
CC
(2.55V ≤V
≤2.70V)
RST
– M41T93Z: V = 2.38V to 5.50V
CC
(2.25V ≤V
≤2.38V)
RST
■ Compatible with SPI Bus serial interface
■ Package options include:
(positive clock SPI modes)
– a 16-Lead QFN or an 18-Lead Embedded
Crystal SOIC
■ Programmable alarm with interrupt function
(valid even during battery back-up mode)
■ RoHS Compliance: lead-free components are
nd
compliant with the RoHS directive.
■ Optional 2 programmable alarm available
■ Square wave output (defaults to 32kHz on
power-up)
■ RESET (RST) output
■ Watchdog timer
■ Programmable 8-bit counter/timer
■ 7 Bytes of battery-backed user SRAM
■ Battery low flag
■ Power-down time stamp (HT Bit)
■ Low operating current of 80µA
■ Oscillator stop detection
■ Battery or super-cap™ Back-up
■ Operating temperature of –40°C to 85°C
August 2006
Rev 1
1/49
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to
change without notice.
www.st.com
49
Contents
M41T93
Contents
1
Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1
SPI signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.1.1
1.1.2
1.1.3
1.1.4
Serial data output (SDO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Serial data input (SDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Serial clock (SCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chip enable (E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2
3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1
2.2
2.3
2.4
SPI bus characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
READ and WRITE cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Data retention and battery switch-over (VSO = VRST) . . . . . . . . . . . . . . . 15
Power-on reset (trec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Clock operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1
3.2
3.3
3.4
Power-down time-stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clock/control register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Real time clock accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Clock calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4.1
3.4.2
Digital calibration (periodic counter correction) . . . . . . . . . . . . . . . . . . . 20
Analog calibration (programmable load capacitance) . . . . . . . . . . . . . . 22
3.5
3.6
3.7
3.8
Setting the alarm clock registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Optional second programmable alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
8-Bit (countdown) timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.8.1
3.8.2
3.8.3
3.8.4
3.8.5
TI/TP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TIE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
TD1/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.9
Square wave output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.10 Battery low warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.11 Century bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2/49
M41T93
Contents
3.12 Output driver pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.13 Oscillator fail detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.14 Oscillator fail interrupt enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.15 Initial power-on defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.16 OTP bit operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4
5
6
7
8
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Package mechanical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3/49
List of Figures
M41T93
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
QFN16 (QA) connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SOX18 (MY) connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Data and clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
READ mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WRITE mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Internal load capacitance adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 10. Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 11. Clock accuracy vs. on-chip load capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 12. Clock divider chain and calibration circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 13. Crystal isolation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 14. Alarm interrupt reset waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 15. Back-up mode alarm waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 16. Measurement AC I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 17. Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 18. Input timing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 19. Output timing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 20. QFN16 – 16-lead, Quad, Flat Package, No Lead, 4x4mm body size, Outline . . . . . . . . . . 43
Figure 21. QFN16 – 16-lead, Quad, Flat, No Lead, 4x4mm, recommended footprint . . . . . . . . . . . . . 45
Figure 22. 32kHz Crystal + QFN16 vs. VSOJ20 mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 23. SOX18 – 18-lead Plastic Small Outline, 300mils, embedded crystal . . . . . . . . . . . . . . . . . 46
4/49
M41T93
List of Tables
List of Tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Signal name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Function table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clock/control register map (32 Bytes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Digital calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Analog calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Alarm repeat modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Timer control register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Interrupt operation (Bit TI/TP = 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Timer source clock frequency selection (244.1µs to 4.25 hrs) . . . . . . . . . . . . . . . . . . . . . . 30
Timer countdown value register bits (addr 11h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Square wave output frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Century bits examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Initial power-on default values (part 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Initial power-up default values (part 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Operating and AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Crystal electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
AC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
QFN16 – 16-lead, Quad, Flat Package, No Lead, 4x4mm body, Mech. Data . . . . . . . . . . 44
SOX18 – 18-lead Plastic SO, 300mils, embedded crystal, pkg. mech. data . . . . . . . . . . . 46
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
5/49
Summary description
M41T93
1
Summary description
The M41T93 is a low power Serial SPI Bus Real Time Clock with a built-in 32.768kHz
oscillator (external crystal-controlled for the QFN16 package, and embedded crystal for the
SOX18 package). Eight bytes of the Register Map (see Table 3 on page 18) are used for the
clock/calendar function and are configured in binary coded decimal (BCD) format. An
additional 17 bytes of the Register Map provide status/control of the two Alarms, Watchdog,
8-Bit Counter, and Square Wave functions. An additional seven bytes are made available as
user SRAM.
Addresses and data are transferred serially via a serial SPI bus-compatible interface. The
built-in address register is incremented automatically after each WRITE or READ data byte.
The M41T93 has a built-in power sense circuit which detects power failures and
automatically switches to the battery supply when a power failure occurs. The energy
needed to sustain the clock operations can be supplied by a small lithium button battery
when a power failure occurs.
Functions available to the user include a non-volatile, time-of-day clock/calendar, Alarm
interrupt, Watchdog Timer, programmable 8-bit Counter, and Square Wave outputs. The
eight clock address locations contain the century, year, month, date, day, hour, minute,
second, and tenths/hundredths of a second in 24 hour BCD format. Corrections for 28, 29
(leap year), 30, and 31 day months are made automatically. The M41T93 is supplied in
either a QFN16 or an SOX18 (MY), 300mil SOIC which includes an embedded 32kHz
crystal. The SOX18 package requires only a user-supplied battery to provide non-volatile
operation.
6/49
M41T93
Summary description
Figure 1.
Logic diagram
V
V
BAT CC
(1)
XI
(2)
SQW
(1)
XO
(3)
IRQ/OUT/FT
SDI
SCL
E
(3)
RST
SDO
V
SS
AI11818
1. For QFN16 package only.
2. Defaults to 32kHz on power-up.
3. Open drain
Table 1.
Signal name
Symbol
Description
XI(1)
XO(1)
IRQ/FT/OUT
SQW(2)
RST
32kHz oscillator input
32kHz oscillator output
Interrupt /frequency test/output driver (open drain)
32kHz programmable square wave output
Power-on reset output (open drain)
Chip enable
E
SDI
Serial data address input
SDO
Serial data address output
SCL
Serial clock input
VBAT
Battery supply voltage (Tie VBAT to VSS if no battery is connected.)
DU(3)
Do not use
Supply voltage
Ground
VCC
VSS
1. For QFN16 package only.
2. Defaults to 32kHz on power-up.
3. DU pin must be allowed to float (remain unconnected)
7/49
Summary description
Figure 2.
M41T93
QFN16 (QA) connections
16
14
15
13
(1)
RST
SDO
1
2
3
4
12
11
(1)
NC
IRQ/FT/OUT
M41T93
NC
(2)
10 SCL
SDI
9
SQW
6
7
5
8
AI11819
1. Open drain output
2. Defaults to 32kHz on power-up.
Figure 3.
SOX18 (MY) connections
1
2
3
4
5
6
7
8
9
18
NC
NC
NF(1)
NF(1)
NC
NF(1)
17
16
15
14
13
12
11
10
NF(1)
V
CC
RST(2)
E
M41T93
DU(3)
SDO
SQW(4)
IRQ/FT/OUT(2)
V
BAT
SCL
SDI
V
SS
AI11820
1. NF pins must be tied to VSS. Pins 2 and 3, and 16 and 17 are internally shorted together.
2. Open drain output
3. Do not use (must be allowed to float)
4. Defaults to 32kHz on power-up.
8/49
M41T93
Summary description
Figure 4.
Block diagram
REAL TIME CLOCK
CALENDAR
OSCILLATOR FAIL
CIRCUIT
OFIE
A1IE
XI
32kHz
OSCILLATOR
XO
CRYSTAL
ALARM1
ALARM2
E
(1)
WATCHDOG
IRQ/FT/OUT
SDI
SPI
INTERFACE
SCL
FT
FREQUENCY TEST
SDO
OUT
TIE
OUTPUT DRIVER
8-BIT COUNTER
SQUARE WAVE
WRITE
PROTECT
V
< V
CC
RST
SQWE
SQW
8 BITS OF OTP
USER SRAM (7 Bytes)
INTERNAL
POWER
V
CC
V
BAT
COMPARE
t
(2)
RST SO
rec
V
/V
(1)
RST
TIMER
AI11821
1. Open drain output
2. VRST = VSO = 2.93V (S), 2.63V (R), and 2.32V (Z).
9/49
Summary description
Figure 5. Hardware hookup
M41T93
V
CC
MCU
(ST6, ST7, ST9, ST10, Others)
M41T93
V
V
CC
CC
(1)
(1)
INT
IRQ/FT/OUT
RST
XI
Reset Input
XO
V
SCL
(2)
SCL
SPI Interface with
SDI
SDO
SDI
(CPOL, CPHA) =
BAT
(0,0) or (1,1)
SDO
V
SS
CS
E
32kHz CLKIN
SQW
AI11822
1. Open drain output
2. CPOL (Clock Polarity) and CPHA (Clock Phase) are bits that may be set in the SPI Control Register of the MCU.
Table 2.
Function table
Mode
E
SCL
SDI
SDO
Disable Reset
WRITE
H
Input Disabled
Input disabled
High Z
L
L
Data bit latch
X
High Z
AI04630
READ
Next data bit shift (1)
AI04631
1. SDO remains at High Z until eight bits of data are ready to be shifted out during a READ.
Figure 6.
Data and clock timing
CPOL
CPHA
0
1
0
1
C
C
MSB
MSB
LSB
SDI
SDO
LSB
AI04632
10/49
M41T93
Summary description
1.1
SPI signal description
1.1.1
Serial data output (SDO)
The output pin is used to transfer data serially out of the Memory. Data is shifted out on the
falling edge of the serial clock.
1.1.2
1.1.3
Serial data input (SDI)
The input pin is used to transfer data serially into the device. Instructions, addresses, and
the data to be written, are each received this way. Input is latched on the rising edge of the
serial clock.
Serial clock (SCL)
The serial clock provides the timing for the serial interface (as shown in Figure 18 on
page 40 and Figure 19 on page 40). The W/R Bit, addresses, or data are latched, from the
input pin, on the rising edge of the clock input. The output data on the SDO pin changes
state after the falling edge of the clock input.
The M41T93 can be driven by a microcontroller with its SPI peripheral running in either of
the two following modes:
(CPOL, CPHA) = ('0', '0'), or
(CPOL, CPHA) = ('1', '1').
For these two modes, input data (SDI) is latched in by the low-to-high transition of clock
SCL, and output data (SDO) is shifted out on the high-to-low transition of SCL (see Table 2
on page 10 and <Blue>Figure 6., page 10).
1.1.4
Chip enable (E)
When E is high, the memory device is deselected, and the SDO output pin is held in its high
impedance state.
After power-on, a high-to-low transition on E is required prior to the start of any operation.
11/49
Operation
M41T93
2
Operation
The M41T93 clock operates as a slave device on the SPI serial bus. Each memory device is
accessed by a simple serial interface that is SPI bus-compatible. The bus signals are SCL,
SDI, and SDO (see Table 1 on page 7 and Figure 5 on page 10). The device is selected
when the Chip Enable input (E) is held low. All instructions, addresses and data are shifted
serially in and out of the chip. The most significant bit is presented first, with the data input
(SDI) sampled on the first rising edge of the clock (SCL) after the Chip Enable (E) goes low.
The 32 bytes contained in the device can then be accessed sequentially in the following
order:
1
2
Tenths/hundredths of a second register
Seconds register
3
Minutes register
4
Century/hours register
Day register
5
6
Date register
7
Month register
8
Year register
9
Digital calibration register
Watchdog register
Alarm1 registers
10
11-15
16
17
18
19
20
21-25
26-32
Flags register
Timer value register
Timer control register
Analog calibration register
Square wave register
Alarm2 registers
User RAM
The M41T93 clock continually monitors V for an out-of tolerance condition. Should V
CC
CC
fall below V , the device terminates an access in progress and resets the device address
RST
counter. Inputs to the device will not be recognized at this time to prevent erroneous data
from being written to the device from a an out-of-tolerance system.
The power input will also be switched from the V pin to the external battery when V falls
CC
CC
below the battery back-up switchover voltage (V = V
). At this time the clock registers
SO
RST
will be maintained by the battery supply. As system power returns and V rises above V
,
SO
CC
the battery is disconnected, and the power supply is switched to external V
.
CC
Write protection continues until V reaches V
(min) plus t
(min). For more
REC
CC
PFD
information on Battery Storage Life refer to Application Note AN1012.
12/49
M41T93
Operation
2.1
SPI bus characteristics
The Serial Peripheral interface (SPI) bus is intended for synchronous communication
between different ICs. It consists of four signal lines: Serial Data Input (SDI), Serial Data
Output (SDO), Serial Clock (SCL) and a Chip Enable (E).
By definition a device that gives out a message is called “transmitter,” the receiving device
that gets the message is called “receiver.” The device that controls the message is called
“master.” The devices that are controlled by the master are called “slaves.”
The E input is used to initiate and terminate a data transfer. The SCL input is used to
synchronize data transfer between the master (micro) and the slave (M41T93) device.
The SCL input, which is generated by the microcontroller, is active only during address and
data transfer to any device on the SPI bus (see Figure 5 on page 10).
The M41T93 can be driven by a microcontroller with its SPI peripheral running in either of
the two following modes:
(CPOL, CPHA) = ('0', '0'), or
(CPOL, CPHA) = ('1', '1').
For these two modes, input data (SDI) is latched in by the low-to-high transition of clock
SCL, and output data (SDO) is shifted out on the high-to-low transition of SCL (see Table 2
and Figure 6 on page 10).
There is one clock for each bit transferred. Address and data bits are transferred in groups
of eight bits. Due to memory size the second most significant address bit is a “Don’t care”
(address bit 6).
2.2
READ and WRITE cycles
Address and data are shifted MSB first into the Serial Data Input (SDI) and out of the Serial
Data Output (SDO). Any data transfer considers the first bit to define whether a READ or
WRITE will occur. This is followed by seven bits defining the address to be read or written.
Data is transferred out of the SDO for a READ operation and into the SDI for a WRITE
operation. The address is always the second through the eighth bit written after the Enable
(E) pin goes low. If the first bit is a '1,' one or more WRITE cycles will occur. If the first bit is a
'0,' one or more READ cycles will occur (see Figure 7 and Figure 8 on page 14).
Data transfers can occur one byte at a time or in multiple byte burst mode, during which the
address pointer will be automatically incremented. For a single byte transfer, one byte is
read or written and then E is driven high. For a multiple byte transfer all that is required is
that E continue to remain low. Under this condition, the address pointer will continue to
increment as stated previously. Incrementing will continue until the device is deselected by
taking E high. The address will wrap to 00h after incrementing to 3Fh.
The system-to-user transfer of clock data will be halted whenever the address being read is
a clock address (00h to 07h). Although the clock continues to maintain the correct time, this
will prevent updates of time and date during either a READ or WRITE of these address
locations by the user. The update will resume either due to a deselect condition or when the
pointer increments to an non-clock or RAM address (08h to 1Fh).
Note:
This is true both in READ and WRITE mode.
13/49
Operation
M41T93
Figure 7.
READ mode sequence
E
0
1
2
3
4
5
6
7
8
9
12 13 14 15 16 17
22
SCL
7 BIT ADDRESS
W/R BIT
3
2
1
7
4
0
6
5
SDI
MSB
DATA OUT
(BYTE 1)
DATA OUT
(BYTE 2)
3
2
1
0
7
5
4
7
6
5
4
3
2
1
0
6
SDO
HIGH IMPEDANCE
MSB
MSB
AI04635
Figure 8.
WRITE mode sequence
E
1
3
6
7
8
9
10
15
0
2
4
5
SCL
DATA BYTE
7 BIT ADDR
W/R BIT
SDI
6
5
4
3
2
1
7
0
7
MSB
6
5
4
3
2
1
0
7
MSB
SDO
HIGH IMPEDANCE
AI04636
14/49
M41T93
Operation
2.3
Data retention and battery switch-over (VSO = VRST)
Once V falls below the switchover voltage (V = V ), the device automatically
RST
CC
SO
switches over to the battery and powers down into an ultra low current mode of operation to
preserve battery life. If V is less than, or greater than V , the device power is switched
BAT
RST
from V to V
when V drops below V
(see Figure 17 on page 39). At this time the
CC
BAT
CC
RST
clock registers and user RAM will be maintained by the attached battery supply.
When it is powered back up, the device switches back from battery to V at V
+
SO
CC
hysteresis. When V rises above V , it will recognize the inputs. For more information
CC
RST
on Battery Storage Life refer to Application Note AN1012.
2.4
Power-on reset (trec)
The M41T93 continuously monitors V . When V falls to the power fail detect trip point,
CC
CC
the RST output pulls low (open drain) and remains low after power-up for t (210ms
rec
typical) after V rises above V
(max).
CC
RST
Note:
The t period does not affect the RTC operation. Write protect only occurs when V is
rec CC
below V . When V rises above V , the RTC will be selectable immediately. Only the
RST
CC
RST
RST output is affected by the t period.
rec
The RST pin is an open drain output and an appropriate pull-up resistor to V should be
CC
chosen to control the rise time.
15/49
Clock operation
M41T93
3
Clock operation
The M41T93 is driven by a quartz-controlled oscillator with a nominal frequency of
32.768kHz. The accuracy of the Real-Time Clock depends on the frequency of the quartz
crystal that is used as the time-base for the RTC.
The 8-byte clock register (see Table 3 on page 18) is used to both set the clock and to read
the date and time from the clock, in binary coded decimal format. Tenths/Hundredths of
Seconds, Seconds, Minutes, and Hours are contained within the first four registers.
Bit D7 of Register 01h contains the STOP Bit (ST). Setting this bit to a '1' will cause the
oscillator to stop. When reset to a '0' the oscillator restarts within one second (typical).
Note:
Upon initial power-up, the user should set the ST Bit to a '1,' then immediately reset the ST
Bit to '0.' This provides an additional “kick-start” to the oscillator circuit.
Bits D6 and D7 of Clock Register 03h (Century/ Hours Register) contain the CENTURY Bit 0
(CB0) and CENTURY Bit 1 (CB1). Bits D0 through D2 of Register 04h contain the Day (day
of week). Registers 05h, 06h, and 07h contain the Date (day of month), Month, and Years.
The ninth clock register is the Digital Calibration Register, while the Analog Calibration
Register is found at address 12h (these are both described in the Clock Calibration section).
Bit D7 of Register 09h (Watchdog Register) contains the Oscillator Fail Interrupt Enable Bit
(OFIE). When the user sets this bit to '1,' any condition which sets the Oscillator Fail Bit (OF)
(see Oscillator fail detection on page 33) will also generate an interrupt output.
Note:
A WRITE to ANY location within the first eight bytes of the clock register (00h-07h),
including the ST Bit and CB0-CB1 Bits will result in an update of the system clock and a
reset of the divider chain. This could result in an inadvertent change of the current time.
These non-clock related bits should be written prior to setting the clock, and remain
unchanged until such time as a new clock time is also written.
The eight Clock Registers may be read one byte at a time, or in a sequential block. Provision
has been made to assure that a clock update does not occur while any of the eight clock
addresses are being read. If a clock address is being read, an update of the clock registers
will be halted. This will prevent a transition of data during the READ.
3.1
Power-down time-stamp
When a power failure occurs, the Halt Update Bit (HT) will automatically be set to a “1”. This
will prevent the clock from updating the Clock/Control registers, and will allow the user to
read the exact time of the power-down event. Resetting the HT Bit to a “0” will allow the
clock to update the Clock/Registers with the current time. For more information, see
Application note AN1572.
16/49
M41T93
Clock operation
3.2
Clock/control register map
The M41T93 offers 32 internal registers which contain Clock, Calibration (Digital and
Analog), Alarm 1 and 2, Watchdog, Flags, Timer, and Square Wave. The Clock registers are
memory locations which contain external (user accessible) and internal copies of the data
®
(usually referred to as BiPORT™ TIMEKEEPER cells). The external copies are
independent of internal functions except that they are updated periodically by the
simultaneous transfer of the incremented internal copy. The internal divider (or clock) chain
will be reset upon the completion of a WRITE to any clock address (00h to 07h). The
system-to-user transfer of clock data will be halted whenever the address being read is a
clock address (00h to 07h). The update will resume either due to a Stop Condition or when
the pointer increments to a non-clock address. Clock and Alarm Registers store data in BCD
format. Calibration, Timer, Watchdog, and Square Wave Bits are written in a Binary Format.
17/49
Clock operation
M41T93
Table 3.
Addr
Clock/control register map (32 Bytes)
Function/Range BCD
Format
D7
D6
0.1 Seconds
10 Seconds
D5
D4
D3
D2
D1
D0
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0.01 Seconds
Seconds
Seconds
00-99
00-59
00-59
ST
0
Seconds
Minutes
10 Minutes
Minutes
CB1
0
CB0
10 Hours
Hours (24 Hour Format)
Day of Week
Date: Day of Month
Month
Century/Hours 0-3/00-23
0
0
0
0
0
0
Day
Date
Month
Year
01-7
01-31
01-12
00-99
0
10 Date
0
0
10M
10 Years
Year
OUT
OFIE
A1IE
FT
DCS
DC4
DC3
DC2
DC1
RB1
DC0 Digital Calibration
BMB4
SQWE
BMB3
BMB2
BMB1
BMB0
RB0
Watchdog
Al1 Month
Al1 Date
ABE Al1 10M
AI1 10 Date
Alarm 1Month
Alarm1 Date
01-12
01-31
00-23
00-59
00-59
0Bh RPT14 RPT15
0Ch RPT13
0Dh RPT12
0Eh RPT11
HT
AI1 10 Hour
Alarm1 Hour
Al1 Hour
Al1 Min
Alarm1 10 Minutes
Alarm1 10 Seconds
AF1 BL
AF2(1)
Alarm1 Minutes
Alarm1 Seconds
Al1 Sec
0Fh
10h
11h
WDF
TF
OF
0
0
Flags
Timer Countdown Value
Timer Value
Timer Control
TE
TI/TP
AC6
TIE
0
0
AC3
0
0
AC2
0
TD1
AC1
TD0
AC0
OTP
Analog
Calibration
12h
ACS
AC5
AC4
13h
14h
RS3
0
RS2
0
RS1
0
RS0
AL2E
SQW
Al2 10M
Alarm2 Month
Alarm2 Month
Alarm2 Date
SRAM/Al2 Month
SRAM/Al2 Date
SRAM/Al2 Hour
SRAM/Al2 Min
SRAM/Al2 Sec
01-12
01-31
00-23
00-59
00-59
15h RPT24 RPT25
AI2 10 Date
AI2 10 Hour
16h RPT23
17h RPT22
18h RPT21
0
Alarm2 10 Minutes
Alarm2 10 Seconds
Alarm2 Minutes
Alarm2 Seconds
19h-
1Fh
User SRAM (7 Bytes)
SRAM
0 = Must be set to zero
OFIE = Oscillator Fail Interrupt Enable
OTP = OTP Control Bit
ABE = Alarm in battery back-up enable Bit
A1IE = Alarm1 interrupt enable bit
AC0-AC6 = analog calibration bits
ACS = analog calibration sign bit
AF1, AF2 = Alarm flag
AL2E = Alarm 2 enable bit
BL = Battery Low Bit
BMB0-BMB4 = Watchdog Multiplier Bits
CB0, CB1 = Century Bits
DC0-DC4 = Digital Calibration Bits
DCS = Digital Calibration Sign Bit
FT = Frequency Test Bit
HT = Halt Update Bit
OF = Oscillator Fail Bit
RB0-RB2 = Watchdog Resolution Bits
RPT11-RPT15 = Alarm 1 Repeat Mode Bits
RPT21-RPT25 = Alarm 2 Repeat Mode Bits
RS0-RS3 = SQW Frequency
SQWE = Square Wave Enable
SRAM/ALM2 = SRAM/Alarm 2 Bit
ST = Stop Bit
TD0, TD1 = Timer Frequency Bits
TE = Timer Enable Bit
TF = Timer Flag
TI/TP = Timer Interrupt or Pulse
TIE = Timer Interrupt Enable
WDF = Watchdog flag
OUT= Output level
1. AF2 will always read ‘0,’ if the AL2E Bit is set to ‘0.’
18/49
M41T93
Clock operation
3.3
Real time clock accuracy
The M41T93 is driven by a quartz controlled oscillator with a nominal frequency of
32,768Hz. The accuracy of the Real Time Clock is dependent upon the accuracy of the
crystal, and the match between the capacitive load of the oscillator circuit and the capacitive
load for which the crystal was trimmed. Temperature also affects the crystal frequency,
causing additional error (see Figure 10 on page 23).
The M41T93 provides the option of clock correction through either manufacturing calibration
or in-application calibration. The total possible compensation is typically –93 ppm to +156
ppm. The two compensation circuits that are available are:
1. An Analog Calibration register (12h) can be used to adjust internal (on-chip) load
capacitors for oscillator capacitance trimming. The individual load capacitors C and
XI
C
(see Figure 9), are selectable from a range of –18pF to +9.75pF in steps of
XO
0.25pF. This translates to a calculated compensation of approximately 30 ppm (see
Analog calibration (programmable load capacitance) on page 22).
2. A Digital Calibration register (08h) can also be used to adjust the clock counter by
adding or subtracting a pulse at the 512Hz divider stage. This approach provides
periodic compensation of approximately –63 ppm to +126 ppm (see Digital calibration
(periodic counter correction) on page 20).
Figure 9.
Internal load capacitance adjustment
XI
C
XI
Crystal Oscillator
XO
C
XO
AI11804
19/49
Clock operation
M41T93
3.4
Clock calibration
The M41T93 oscillator is designed for use with a 12.5pF crystal load capacitance. When the
calibration circuit is properly employed, accuracy improves to better than 1 ppm at 25°C.
The M41T93 design provides the following two methods for clock error correction.
3.4.1
Digital calibration (periodic counter correction)
This method employs the use of periodic counter correction by adjusting the ratio of the
100Hz divider stage to the 512Hz divider stage. Under normal operation, the 100Hz divider
stage outputs precisely 100 pulses for every 512 pulses of the 512Hz input stage to provide
the input frequency to the Fraction of Seconds Clock register. By adjusting the number of
512Hz input pulses used to generate 100 output pulses, the clock can be sped up or slowed
down, as shown in Figure 12 on page 25.
When a non-zero value is loaded into the five Calibration Bits (DC4 – DC0) found in the
Digital Calibration Register (08h) and the sign bit is ‘1,’ (indicating positive calibration), the
100Hz stage outputs 100 pulses for every 511 input pulses instead of the normal 512. Since
the 100 pulses are now being output in a shorter window, this has the effect of speeding up
the clock by 1/512 seconds for each second the circuit is active. Similarly, when the sign bit
is ‘0,’ indicating negative calibration, the block outputs 100 pulses for every 513 input pulses.
Since the 100 pulses are then being output in a longer window, this has the effect of slowing
down the clock by 1/512 seconds for each second the circuit is active.
The amount of calibration is controlled by using the value in the calibration register (N) to
generate the adjustment in one second increments. This is done N times per minute, for
every minute, for positive calibration, and N times per minute every other minute for negative
calibration (see Table 4 on page 21).
For example, if the Calibration register is set to '100010,' then the adjustment will occur for
two seconds in every minute. Similarly, if the calibration register is set to '000011,' then the
adjustment will occur for 3 seconds in every alternating minute.
The Digital Calibration Bits (DC4 – DC0) occupy the five lower order bits in the Digital
Calibration Register (08h). These bits can be set to represent any value between 0 and 31 in
binary form. The sixth bit (DCS) is a Sign Bit; '1' indicates positive calibration, '0' indicates
negative calibration. Calibration occurs within an 8-minute (positive) or 16-minute (negative)
cycle. Therefore, each calibration step has an effect on clock accuracy of +4.068 or –2.034
ppm. Assuming that the oscillator is running at exactly 32,768Hz, each of the 31 increments
in the Calibration byte would represent +10.7 or –5.35 seconds per month, which
corresponds to a total range of +5.5 or –2.75 minutes per month.
Note:
The modified pulses are not observable on the Frequency Test (FT) output, nor will the
effect of the calibration be measurable real-time, due to the periodic nature of the error
compensation.
20/49
M41T93
Clock operation
Table 4.
Digital calibration values
Calibration value rounded to the nearest ppm
Calibration value (binary)
DC4 – DC0
Negative calibration (DCS = 0) Positive calibration (DCS = 1)
0 (00000)
1 (00001)
2 (00010)
3 (00011)
4 (00100)
5 (00101)
6 (00110)
7 (00111)
8 (01000)
9 (01001)
10 (01010)
11 (01011)
12 (01100)
13 (01101)
14 (01110)
15 (01111)
16 (10000)
17 (10001)
18 (10010)
19 (10011)
20 (10100)
21 (10101)
22 (10110)
23 (10111)
24 (11000)
25 (11001)
26 (11010)
27 (11011)
28 (11100)
29 (11101)
30 (11110)
31 (11111)
N
0
0
–2
4
–4
8
–6
12
–8
16
–10
20
–12
24
–14
28
–16
33
–18
37
–20
41
–22
45
–24
49
–26
53
–28
57
–31
61
–33
65
–35
69
–37
73
–39
77
–41
81
–43
85
–45
90
–47
94
–49
98
–51
102
–53
106
–55
110
–57
114
–59
118
–61
–63
122
126
N/491520 (per minute)
N/245760 (per minute)
21/49
Clock operation
M41T93
3.4.2
Analog calibration (programmable load capacitance)
A second method of calibration employs the use of programmable internal load capacitors to
adjust (or trim) the oscillator frequency.
By design, the oscillator is intended to be 0 ppm crystal accuracy at room temperature
(25°C, see Figure 10 on page 23). For a 12.5pF crystal, the default loading on each side of
the crystal will be 25pF. For incrementing or decrementing the calibration value, capacitance
will be added or removed in increments of 0.25pF to each side of the crystal.
Internally, C
of the oscillator is changed via two digitally controlled capacitors, C and
XI
LOAD
C
, connected from the XI and XO pins to ground (see Figure 9 on page 19). The effective
XO
on-chip series load capacitance, C
of 12.5pF (AC0-AC6 = ‘0’).
, ranges from 3.5pF to 17.4pF, with a nominal value
LOAD
The effective series load capacitance (C
) is the combination of C and C
:
XO
LOAD
XI
C
= 1 ⁄ (1 ⁄ C + 1 ⁄ C
)
XO
LOAD
XI
Seven analog calibration bits, AC0 to AC6, are provided in order to adjust the on-chip load
capacitance value for frequency compensation of the RTC. Each bit has a different weight
for capacitance adjustment. An Analog Calibration Sign (ACS) bit determines if capacitance
is added (ACS Bit = ‘0,’ negative calibration) or removed (ACS Bit = ‘1,’ positive calibration).
The majority of the calibration adjustment is positive (i.e. to increase the oscillator frequency
by removing capacitance) due to the typical characteristic of quartz crystals to slow down
due to changes in temperature, but negative calibration is also available.
Since the Analog Calibration Register adjustment is essentially “pulling” the frequency of the
oscillator, the resulting frequency changes will not be linear with incremental capacitance
changes. The equations which govern this mechanism indicate that smaller capacitor values
of Analog Calibration adjustment will provide larger increments. Thus, the larger values of
Analog Calibration adjustment will produce smaller incremental frequency changes. These
values typically vary from 6-10 ppm/bit at the low end to <1 ppm/bit at the highest
capacitance settings. The range provided by the Analog Calibration Register adjustment
with a typical surface mount crystal is approximately 30 ppm around the AC6-AC0 = 0
default setting because of this property (see Table 5 on page 23).
22/49
M41T93
Clock operation
Figure 10. Crystal accuracy across temperature
Frequency (ppm)
20
0
–20
–40
–60
2
∆F
F
= K x (T – TO)
–80
–100
–120
–140
–160
= –0.036 ppm/°C2 0.006 ppm/°C2
O = 25°C 5°C
K
T
–40
–30
–20
–10
0
10
20
30
40
50
60
70
80
Temperature °C
AI07888
Table 5.
Addr
Analog calibration values
Analog
(1)
Calibration
Value
D7
D6
D5
D4
D3
D2
D1
D0
CXI, CXO CLOAD
ACS
( )
AC6
AC5
AC4
AC3
AC2
AC1
AC0
(16pF) (8pF) (4pF) (2pF) (1pF) (0.5pF) (0.25pF)
0pF
3pF
x
0
0
1
0
1
0
0
0
0
0
1
0
0
0
0
1
0
0
0
1
1
0
0
0
1
0
1
0
1
0
1
1
1
1
0
0
0
0
0
1
0
0
0
0
0
1
0
25pF
28pF
30pF
18pF
12.5pF
14pF
15pF
9pF
5pF
12h
–7pF
9.75pF(2)
–18pF(3)
34.75pF 17.4pF
7pF 3.5pF
1. CLOAD = 1/(1/CXI + 1/CXO
)
2. Maximum negative calibration value
3. Maximum positive calibration value
23/49
Clock operation
M41T93
The on-chip capacitance can be calculated as follows:
= [( AC6– AC0 value, decimal) × 0,25pF] + 7pF
C
LOAD
For example:
C
C
C
(12h = x0000000) = 12.5pF,
(12h =11001000) = 3.5pF, and
(12h = 00100111) = 17.4pF.
LOAD
LOAD
LOAD
The oscillator sees a minimum of 3.5pF with no programmable load capacitance selected.
Note:
These are typical values, and the total load capacitance seen by the crystal will include
approximately 1-2pF of package and board capacitance in addition to the Analog Calibration
register value.
Any invalid value of Analog Calibration will result in the default capacitance of 25pF.
The combination of analog and digital trimming can give up to –93 to +156 ppm of the total
adjustment.
Figure 11 on page 24 represents a typical curve of clock ppm adjustment versus the Analog
Calibration value. This curve may vary with different crystals, so it is good practice to
evaluate the crystal to be used with an M41T93 device before establishing the adjustment
values for the application in question.
Figure 11. Clock accuracy vs. on-chip load capacitors
100.0
90.0
80.0
70.0
60.0
50.0
40.0
30.0
20.0
10.0
0.0
–10.0
–20.0
–10.0
–5.0
0.0
5.0
10.0
15.0
20.0
Analog Calibration Value
AI12293
24/49
M41T93
Clock operation
Two methods are available for ascertaining how much calibration a given M41T93 may
require:
The first involves setting the clock, letting it run for a month and comparing it to a known
●
accurate reference and recording deviation over a fixed period of time. This allows the
designer to give the end user the ability to calibrate the clock as the environment
requires, even if the final product is packaged in a non-user serviceable enclosure. The
designer could provide a simple utility that accesses either or both of the Calibration
bytes.
●
The second approach is better suited to a manufacturing environment, and involves the
use of the IRQ/FT/OUT pin. The IRQ/FT/ OUT pin will toggle at 512Hz when FT and
OUT Bits = '1' and ST = '0.' Any deviation from 512Hz indicates the degree and
direction of oscillator frequency shift at the test temperature. For example, a reading of
512.010124Hz would indicate a +20 ppm oscillator frequency error, requiring either a –
10 (xx001010) to be loaded into the Digital Calibration byte, or +6pF (00011000) into
the Analog Calibration byte for correction.
Note:
Setting or changing the Digital Calibration Byte does not affect the Frequency Test, Square
Wave, or Watchdog Timer frequency, but changing the Analog Calibration byte DOES affect
all functions derived from the low current oscillator (see Figure 12).
Figure 12. Clock divider chain and calibration circuits
512Hz Output
Frequency Test
Remainder of
Divider Circuit
Square Wave
Watchdog Timer
8-Bit Timer
÷2
÷8
÷2
÷2
÷2
÷2
C
XI
Low Current
Oscillator
32kHz
Digital Calibration Circuitry
(divide by 511/512/513)
Clock
Registers
C
XO
1Hz Signal
Analog Calibration
Circuitry
AI11806a
25/49
Clock operation
Figure 13. Crystal isolation example
M41T93
Crystal
Local Grounding
Plane (Layer 2)
XO
XI
V
SS
AI11814
Note:
The substrate pad should be tied to V
.
SS
3.5
Setting the alarm clock registers
Address locations 0Ah-0Eh (Alarm 1) and 14h-18h (Alarm 2) contain the alarm settings.
Either alarm can be configured independently to go off at a prescribed time on a specific
month, date, hour, minute, or second, or repeat every year, month, day, hour, minute, or
second. Bits RPT15–RPT11 and RPT25-RPT21 put the alarms in the repeat mode of
operation. Table 6 on page 27 shows the possible bit configurations.
Codes not listed in the table default to the once-per-second mode to quickly alert the user of
an incorrect alarm setting. When the clock information matches the alarm clock settings
based on the match criteria defined by RPT15–RPT11 and/or RPT25-RPT21, AF1 (Alarm 1
Flag) or AF2 (Alarm 2 Flag) is set. If A1IE (Alarm 1 Interrupt Enable) is set, the alarm
condition activates the IRQ/FT/OUT output pin. To disable either of the alarms, write a '0' to
the Alarm Date Registers and to the RPTx5–RPTx1 Bits.
Note:
If the address pointer is allowed to increment to the Flag Register address, or the last
address written is “Alarm Seconds,” the address pointer will increment to the Flag address,
and an alarm condition will not cause the Interrupt/Flag to occur until the address pointer is
moved to a different address.
The IRQ output is cleared by a READ to the Flags Register (0Fh) as shown in Figure 14. A
subsequent READ of the Flags Register is necessary to see that the value of the Alarm Flag
has been reset to '0.'.
The IRQ/FT/OUT pin can also be activated in the battery back-up mode (see Figure 15 on
page 27).
26/49
M41T93
Clock operation
3.6
Optional second programmable alarm
When the Alarm 2 Enable (AL2E) Bit (D1 of address 13h) is set to a logic ‘1,’ registers 14h
through 18h provide control for a second programmable alarm which operates in the same
manner as the alarm function described above.
The AL2E Bit defaults on initial power-up to a logic ‘0’ (Alarm 2 disabled). In this mode, the
five address bytes (14h-18h) function as additional user SRAM, for a total of 12 bytes of
user SRAM.
Figure 14. Alarm interrupt reset waveform
0Eh
0Fh
00h
ALARM FLAG BITS (AF )
x
HIGH-Z
IRQ/FT/OUT
AI11823
Figure 15. Back-up mode alarm waveform
V
CC
V
PFD
V
SO
trec
AF Bits in Flags
x
Register
IRQ/FT/OUT
HIGH-Z
AI11824
Note:
ABE and A1IE Bits = 1.
Table 6.
RPT5
Alarm repeat modes
RPT4
RPT3
RPT2
RPT1
Alarm setting
1
1
1
1
1
0
1
1
1
1
0
0
1
1
1
0
0
0
1
1
0
0
0
0
1
0
0
0
0
0
Once per Second
Once per Minute
Once per Hour
Once per Day
Once per Month
Once per Year
27/49
Clock operation
M41T93
3.7
Watchdog timer
The watchdog timer can be used to detect an out-of-control microprocessor. The user
programs the watchdog timer by setting the desired amount of time-out into the Watchdog
Register, address 09h. Bits BMB4-BMB0 store a binary multiplier and the two lower order
bits RB1-RB0 select the resolution, where 00 = 1/16 second, 01 = 1/4 second, 10 = 1
second, and 11 = 4 seconds. The amount of time-out is then determined to be the
multiplication of the five-bit multiplier value with the resolution. (For example: writing
00001110 in the Watchdog Register = 3*1, or 3 seconds). If the processor does not reset
the timer within the specified period, the M41T93 sets the WDF (Watchdog Flag) and
generates a watchdog interrupt.
The watchdog timer can be reset by having the microprocessor perform a WRITE of the
Watchdog Register. The time-out period then starts over.
Should the watchdog timer time-out, a value of 00h needs to be written to the Watchdog
Register in order to clear the IRQ/FT/OUT pin. This will also disable the watchdog function
until it is again programmed correctly. A READ of the Flags Register will reset the Watchdog
Flag (Bit D7; Register 0Fh).
The watchdog function is automatically disabled upon power-up and the Watchdog Register
is cleared. If the watchdog function is set, the frequency test function is activated, and the
SQWE Bit is '0,' the watchdog function prevails and the frequency test function is denied.
3.8
8-Bit (countdown) timer
The Timer Value Register is an 8-bit binary countdown timer. It is enabled and disabled via
the Timer Control Register (11h) TE Bit. Other timer properties such as the source clock, or
interrupt generation are also selected in the Timer Control Register (see Table 7). For
accurate read back of the countdown value, the serial clock (SCL) must be operating at a
frequency of at least twice the selected timer clock.
The Timer Control register selects one of four source clock frequencies for the timer (4096,
64, 1, or 1/60Hz), and enables/disables the timer. The timer counts down from a software-
loaded 8-bit binary value. At the end of every countdown, the timer sets the Timer Flag (TF)
Bit. The TF Bit can only be cleared by software. When asserted, the timer flag (TF) can also
be used to generate an interrupt (IRQ/FT/OUT) on the M41T93. The interrupt may be
generated as a pulsed signal every countdown period or as a permanently active signal
which follows the condition of TF. The Timer Interrupt/Timer Pulse (TI/TP) Bit is used to
control this mode selection. When reading the timer, the current countdown value is
returned.
Table 7.
Addr
Timer control register map
D7
D6
D5
D4
D3
D2
D1
D0
Function
0Fh
10h
11h
WDF
AF1
AF2
BL
TF
OF
0
0
Flags
Timer Countdown Value
TIE
Timer Value
Timer Control
TE
TI/TP
0
0
0
TD1
TD0
Note:
Bit positions labeled with ‘0’ should always be written with logic '0.'
28/49
M41T93
Clock operation
3.8.1
TI/TP
●
TI/TP = 0
IRQ/FT/OUT is active when TF is logic '1' (subject to the status of the Timer Interrupt
Enable Bit (TIE).
●
TI/TP = 1
IRQ/FT/OUT pulses active according to Table 8 (subject to the status of the TIE Bit).
Note:
If an alarm condition, watchdog time-out, oscillator failure, or OUT = 0 cause IRQ/FT/OUT to
be asserted low, then IRQ/FT/OUT will remain asserted even if TI/TP is set to '1.' When in
pulse mode (TI/TP = 1), clearing the TF Bit will not stop the pulses on IRQ/FT/OUT. The
output pulses will only stop if TE, TIE, or TI/TP are reset to '0.'
Table 8.
Interrupt operation (Bit TI/TP = 1)
IRQ(1) Period(s)
Source clock (Hz)
n(2) = 1
n > 1
4096
64
1/8192
1/128
1/64
1/4096
1/64
1
1/64
1/60
1/64
1/64
1. TF and IRQ/FT/OUT become active simultaneously.
2. n = loaded countdown timer value. The timer is stopped when n = 0.
3.8.2
TF
At the end of a timer countdown, TF is set to logic '1.' If both timer and alarm interrupts are
required in the application, the source of the interrupt can be determined by reading the flag
bits. The timer will auto-reload and continue to count down regardless of the state of TF Bit
(or TI/TP Bit). The TF Bit is cleared by reading the Flags Register.
3.8.3
3.8.4
TIE
In Level mode (TI/TP = 0), when TF is asserted, the interrupt is asserted (if TIE = 1). To
clear the interrupt, the TF Bit or the TIE Bit must be reset.
TE
●
TE = 0
When the Timer Register (10h) is set to ‘0,’ the timer is disabled.
TE = 1
●
The timer is enabled. TE is reset (disabled) on power-down. When re-enabled, the
counter will begin from the same value as when it was disabled.
29/49
Clock operation
M41T93
3.8.5
TD1/0
These are the timer source clock frequency selection bits (see Table 9). These bits
determine the source clock for the countdown timer (see Table 10). When not in use, the
TD1 and TD0 Bits should be set to ‘11’ (1/60Hz) for power saving.
Table 9.
Timer source clock frequency selection (244.1µs to 4.25 hrs)
TD1
TD0
Timer source clock frequency (Hz)
0
0
1
1
0
1
0
1
4096 (244.1µs)
64 (15.6ms)
1 (1s)
1/60 (60s)
Table 10. Timer countdown value register bits (addr 11h)
Bit
Symbol
Description
This register holds the loaded countdown value ‘n.’
Countdown Period = n / Source Clock frequency.
<timer countdown
value>
7 - 0
Note:
Writing to the timer register will not reset the TF Bit or clear the interrupt.
30/49
M41T93
Clock operation
3.9
Square wave output
The M41T93 offers the user a programmable square wave function which is output on the
SQW pin. RS3-RS0 bits located in 13h establish the square wave output frequency. These
frequencies are listed in Table 4. Once the selection of the SQW frequency has been
completed, the SQW pin can be turned on and off under software control with the Square
Wave Enable Bit (SQWE) located in Register 0Ah.
Note:
If the SQWE Bit is set to '1', and V falls below the switchover (V ) voltage, the
CC SO
squarewave output will be disabled.
Table 11. Square wave output frequency
Square Wave Bits
Square Wave
RS3
RS2
RS1
RS0
Frequency
Units
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
None
32.768
8.192
4.096
2.048
1.024
512
256
128
64
–
kHz
kHz
kHz
kHz
kHz
Hz
Hz
Hz
Hz
32
Hz
16
Hz
8
Hz
4
Hz
2
Hz
1
Hz
31/49
Clock operation
M41T93
3.10
Battery low warning
The M41T93 automatically performs battery voltage monitoring upon power-up and at
factory-programmed time intervals of approximately 24 hours. The Battery Low (BL) Bit, Bit
D4 of Flags Register 0Fh, will be asserted if the battery voltage is found to be less than
approximately 2.5V. The BL Bit will remain asserted until completion of battery replacement
and subsequent battery low monitoring tests, either during the next power-up sequence or
the next scheduled 24-hour interval.
If a battery low is generated during a power-up sequence, this indicates that the battery is
below approximately 2.5 volts and may not be able to maintain data integrity. Clock data
should be considered suspect and verified as correct. A fresh battery should be installed.
If a battery low indication is generated during the 24-hour interval check, this indicates that
the battery is near end of life. However, data is not compromised due to the fact that a
nominal V is supplied. In order to insure data integrity during subsequent periods of
CC
battery back-up mode, the battery should be replaced.
The M41T93 only monitors the battery when a nominal V is applied to the device. Thus
CC
applications which require extensive durations in the battery back-up mode should be
powered-up periodically (at least once every few months) in order for this technique to be
beneficial. Additionally, if a battery low is indicated, data integrity should be verified upon
power-up via a checksum or other technique.
3.11
Century bits
These two bits will increment in a binary fashion at the turn of the century, and handle all
leap years correctly. See Table 12 for additional explanation.
Table 12. Century bits examples
CB0
CB1
Leap Year?
Example(1)
0
0
1
1
0
1
0
1
Yes
No
No
No
2000
2100
2200
2300
1. Leap year occurs every four years (for years evenly divisible by four), except for years evenly divisible by
100. The only exceptions are those years evenly divisible by 400 (the year 2000 was a leap year, year
2100 is not).
3.12
Output driver pin
When the OFIE Bit, A1IE Bit, and Watchdog Register are not set to generate an interrupt,
the IRQ/FT/OUT pin becomes an output driver that reflects the contents of D7 of register
08h. In other words, when D7 (OUT Bit) is a '0,' then the IRQ/FT/OUT pin will be driven low.
Note:
The IRQ/FT/OUT pin is an open drain which requires an external pull-up resistor.
32/49
M41T93
Clock operation
3.13
Oscillator fail detection
If the Oscillator Fail (OF) Bit is internally set to a '1,' this indicates that the oscillator has
either stopped, or was stopped for some period of time and can be used to judge the validity
of the clock and date data. This bit will be set to '1' any time the oscillator stops.
In the event the OF Bit is found to be set to '1' at any time other than the initial power-up, the
STOP Bit (ST) should be written to a '1,' then immediately reset to '0.' This will restart the
oscillator. The following conditions can cause the OF Bit to be set:
●
The first time power is applied (defaults to a '1' on power-up).
Note:
If the OF Bit cannot be written to '1' four seconds after the initial power-up, the STOP Bit
(ST) should be written to a '1,' then immediately reset to '0.'
●
●
●
The voltage present on VCC or battery is insufficient to support oscillation.
The ST Bit is set to '1.'
External interference of the crystal
For the M41T93, if the Oscillator Fail Interrupt Enable Bit (OFIE) is set to a '1,' the
IRQ/FT/OUT pin will also be activated. The IRQ/FT/OUT output is cleared by resetting the
OFIE or OF Bit to '0' (NOT by reading the Flag Register).
The OF Bit will remain set to '1' until written to logic '0.' The oscillator must start and have
run for at least 4 seconds before attempting to reset the OF Bit to '0.' If the trigger event
occurs during a power down condition, this bit will be set correctly.
3.14
Oscillator fail interrupt enable
If the Oscillator Fail Interrupt Bit (OFIE) is set to a '1,' the IRQ/FT/OUT pin will also be
activated. The IRQ/FT/OUT output is cleared by resetting the OFIE or OF Bit to '0' (not be
reading the Flags Register).
33/49
Clock operation
M41T93
3.15
Initial power-on defaults
Upon initial application of power to the device, the register bits will initially power-on in the
state indicated in Table 13 and Table 14.
Table 13. Initial power-on default values (part 1)
DCS
ACS
Digital Analog
Calib. Calib.
Watchdog
Condition(1) ST CB1 CB0 OUT FT
OFIE
A1IE SQWE ABE
(3)
Initial
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
Power-up
Subsequent
Power-up(2,4)
UC UC UC UC
UC
UC
UC
UC
UC
UC
UC
1. All other control bits power-up in an undetermined state.
2. With battery back-up
3. BMB0-BMB4, RB0, RB1
4. UC = Unchanged
Table 14. Initial power-up default values (part 2)
RPT21-
Condition(1) RPT11-15 HT OF TE TI/TP TIE TD1 TD0 RS0 RS1-3 OTP
AL2E
25
Initial
0
1
1
1
0
0
0
0
1
1
1
0
0
0
0
Power-up
Subsequent
Power-up(2,3)
UC
UC
UC
UC UC UC UC
UC
UC
UC
UC
1. All other control bits power-up in an undetermined state.
2. With battery back-up
3. UC = Unchanged
3.16
OTP bit operation
When the OTP (One Time Programmable) Bit is set to a '1,' the value in the internal OTP
registers will be transferred to the analog calibration register (12h) and are “Read only.” The
OTP value is programmed by the manufacturer, and will contain the calibration value
necessary to achieve 5 ppm at room temperature.
If the OTP Bit is set to '0,' the analog calibration register will become a WRITE/READ
register and function like standard SRAM memory cells, allowing the user to implement any
desired value of analog calibration.
When the user sets the OTP Bit, they need to wait for approximately 3 to 4ms before the
analog registers transfer the value from the OTP to the analog registers due to the OTP
Read operation.
34/49
M41T93
Maximum rating
4
Maximum rating
Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 15. Absolute maximum ratings
Symbol
Parameter
Value(1)
Unit
TSTG
VCC
Storage temperature (VCC Off, Oscillator Off)
Supply voltage
–55 to 125
°C
V
–0.3 to 7.0
(2)
TSLD
Lead solder temperature for 10 seconds
Input or output voltages
Output current
260
°C
V
VIO
IO
–0.2 to Vcc+0.3
20
1
mA
W
PD
Power dissipation
1. Data based on characterization results, not tested in production.
2. Reflow at peak temperature of 260°C (total thermal budget not to exceed 245°C for greater than 30
seconds).
35/49
DC and AC parameters
M41T93
5
DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC Characteristic
tables are derived from tests performed under the Measurement Conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Table 16. Operating and AC measurement conditions
Parameter
M41T93
Supply Voltage (VCC
)
2.38V to 5.5V
–40 to 85°C
30pF
Ambient operating temperature (TA)
Load capacitance (CL, typical)
Input rise and fall times
≤50ns
Input pulse voltages
0.2VCC to 0.8 VCC
0.3VCC to 0.7 VCC
Input and output timing ref. voltages
Note:
Output Hi-Z is defined as the point where data is no longer driven.
Figure 16. Measurement AC I/O waveform
0.8V
CC
0.7V
CC
0.3V
CC
0.2V
CC
AI02568
Table 17. Capacitance
Symbol
Parameter(1,2)
Min
Max
Unit
CIN
Input capacitance
Output capacitance
7
pF
pF
(3)
COUT
10
1. Effective capacitance measured with power supply at 3.6V; sampled only, not 100% tested.
2. At 25°C, f = 1MHz.
3. Outputs deselected.
36/49
M41T93
DC and AC parameters
Table 18. DC Characteristics
Sym
Parameter
Test condition(1)
Min
Typ
Max
Unit
Operating voltage (S)
–40 to 85°C
–40 to 85°C
3.00
2.70
2.38
5.50
5.50
5.50
1
V
V
VCC Operating voltage (R)
Operating voltage (Z)
–40 to 85°C
V
ILI
Input leakage current
Output leakage current
0V ≤VIN ≤VCC
0V ≤VOUT ≤VCC
fSCL = 2MHz
fSCL = 5MHz
fSCL = 10MHz
µA
µA
µA
µA
µA
µA
µA
µA
V
ILO
1
tbd
tbd
tbd
10
Supply current
ICC1 SCL = 0.1VCC/0.9VCC
SDO = Open
5.5V
3.0V
7
E = VCC
;
All inputs ≥ VCC – 0.2V;
≤VSS + 0.2V
ICC2 Supply current (standby)
TBD
TBD
2.5V (Z only)
VIL
VIH
Input low voltage
Input high voltage
–0.3
0.3VCC
0.7VCC
VCC+0.3
V
VCC/VBAT = 3.0V,
IOL = 1.0mA
RST, FT/RST
SQW, IRQ/FT/OUT
SDO
0.4
0.4
0.4
V
V
VCC = 3.0V,
IOL = 1.0mA
VOL Output low voltage
VCC = 3.0V,
V
V
IOL = 3.0mA
VOH Output high voltage
VCC = 3.0V, IOH = –1.0mA (push-pull)
IRQ/FT/OUT
2.4
1.8
Pull-up supply voltage
(open drain)
5.5
5.5
V
VBAT Back-up supply voltage
V
25°C; VCC = 0V; OSC On; VBAT = 3V;
32kHz Off
IBAT Battery supply current
365
450
nA
1. Valid for Ambient Operating Temperature: TA = –40 to 85°C; VCC = 2.38V to 5.5V (except where noted).
37/49
DC and AC parameters
M41T93
Units
Table 19. Crystal electrical characteristics
Symbol
Parameter(1,2)
Min
Typ
Max
fO
RS
CL
Resonant frequency
32.768
kHz
kΩ
pF
Series resistance
Load capacitance
65(3)
12.5
Note:
1
Externally supplied if using the QFN16 package. STMicroelectronics recommends the
Citizen CFS-145 (1.5x5mm) and the KDS DT-38 (3x8mm) for thru-hole, or the KDS DMX-
26S (3.2x8mm) for surface-mount, tuning fork-type quartz crystals.
KDS can be contacted at kouhou@kdsj.co.jp or http://www.kdsj.co.jp.
Citizen can be contacted at csd@citizen-america.com or http://www.citizencrystal.com.
2
3
Load capacitors are integrated within the M41T93. Circuit board layout considerations for
the 32.768kHz crystal of minimum trace lengths and isolation from RF generating signals
should be taken into account.
Guaranteed by design.
Table 20. Oscillator characteristics
Symbol
Parameter(1,2)
Conditions
Min
Typ
Max
Units
VSTA
tSTA
Oscillator start voltage
≤4s
2.0
V
s
Oscillator start time
VCC = VSO
1
(1)
CXI, CXO
Capacitor Input, capacitor output
IC-to-IC frequency variation(2,3)
25
pF
ppm
–10
+10
1. With default Analog Calibration value ( = 0).
2. Reference value
3. TA = 25°C, VCC = 5.0V.
38/49
M41T93
DC and AC parameters
Figure 17. Power down/up mode AC waveforms
V
CC
V
SO
tPD
trec
SCL
SDI
DON'T CARE
AI11839
Table 21. Power down/up trip points DC characteristics
Sym
Parameter(1,2)
Min
Typ
Max
Unit
S
R
Z
2.85
2.55
2.25
VRST
25
2.93
2.63
2.32
3.0
2.7
V
V
VRST Reset threshold voltage
2.38
V
Battery back-up switchover
V
VSO
Hysteresis
mV
ms
Reset pulse Width (VCC Rising)
trec
140
280
VCC to Reset Delay, VCC = (VRST + 100mV), falling to
(VRST – 100mV; for VCC slew rate of 10mV/µs
2.5
µs
1. All voltages referenced to VSS
.
2. Valid for Ambient Operating Temperature: TA = –40 to 85°C; VCC = 2.38 to 5.5V (except where noted).
39/49
DC and AC parameters
M41T93
Figure 18. Input timing requirements
tEHEL
E
tCHEL
tELCH
tCHEH
tEHCH
SCL
tDVCH
tCHCL
tCHDX
tCLCH
MSB IN
LSB IN
SDI
tDLDH
tDHDL
HIGH IMPEDANCE
SDO
AI12295
Figure 19. Output timing requirements
E
tCH
SCL
tCLQV
tCL
tEHQZ
tCLQX
MSB OUT
LSB OUT
SDO
tQLQH
tQHQL
SDIADDR. LSB IN
AI04634
40/49
M41T93
DC and AC parameters
Table 22. AC characteristics
VCC < 2.7V
VCC ≥ 2.7V
Sym
Parameter(1)
Units
Min
Max
Min
Max
fSCL
SCL clock frequency
E Active setup time
E Not active setup time
E Deselect time
D.C.
90
5
D.C.
30
30
40
30
30
40
40
10
MHz
ns
ns
ns
ns
ns
ns
ns
µs
µs
ns
ns
ns
ns
ns
ns
ns
tELCH
tEHCH
tEHEL
tCHEH
tCHEL
90
100
90
E Active hold time
E Not active hold time
Clock high time
90
(2)
tCH
90
(2)
tCL
Clock low time
90
(3)
tCLCH
Clock rise time
1
1
2
2
(3)
tCHCL
tDVCH
tCHDX
Clock fall time
Data in setup time
Data in hold time
Output disable time
Clock low to output valid
Output hold time
Output rise time
20
30
10
10
(3)
tEHQZ
tCLQV
tCLQX
100
60
40
40
0
0
(3)
tQLQH
50
50
40
40
(3)
tQHQL
Output fall time
1. Valid for Ambient Operating Temperature: TA = –40 to 85°C; VCC = 2.38 to 5.5V (except where noted).
2. tCH and tCL must never be lower than the shortest possible clock period, 1/fC(max)
3. Value guaranteed by characterization, not 100% tested in production.
41/49
Package mechanical information
M41T93
6
Package mechanical information
®
In order to meet environmental requirements, ST offers these devices in ECOPACK
packages. These packages have a Lead-free second level interconnect . The category of
second Level Interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at www.st.com.
42/49
M41T93
Package mechanical information
Figure 20. QFN16 – 16-lead, Quad, Flat Package, No Lead, 4x4mm body size, Outline
D
E
A3
A
A1
ddd C
e
b
L
K
1
2
3
(2)
Ch
E2
K
D2
QFN16-A2
1. Drawing is not to scale.
2. Substrate pad should be tied to VSS
.
43/49
Package mechanical information
M41T93
Max
Table 23. QFN16 – 16-lead, Quad, Flat Package, No Lead, 4x4mm body, Mech. Data
mm
Min
inches
Min
Sym
Typ
Max
Typ
A
A1
A3
b
0.90
0.02
0.20
0.30
4.00
–
0.80
0.00
–
1.00
0.05
–
0.035
0.001
0.008
0.010
0.118
0.067
0.118
0.067
0.020
0.008
0.016
–
0.032
0.000
–
0.039
0.002
–
0.25
3.90
2.50
3.90
2.50
–
0.35
4.10
2.80
4.10
2.80
–
0.007
0.114
0.061
0.114
0.061
–
0.012
0.122
0.071
0.122
0.071
–
D
D2
E
4.00
–
E2
e
0.65
0.20
0.40
–
K
–
–
–
–
L
0.30
0.08
0.33
16
0.50
–
0.012
0.003
0.013
16
0.020
–
ddd
Ch
N
–
–
–
–
44/49
M41T93
Package mechanical information
Figure 21. QFN16 – 16-lead, Quad, Flat, No Lead, 4x4mm, recommended footprint
2.70
0.70
0.20
(2)
4.50
2.70
0.35
0.325
0.65
AI11815
1. Dimensions shown are in millimeters (mm).
2. Substrate pad should be tied to VSS
.
Figure 22. 32kHz Crystal + QFN16 vs. VSOJ20 mechanical data
6.0 0.2
3.2
VSOJ20
SMT
CRYSTAL
1.5
3.9
7.0 0.3
1
2
3
4
ST QFN16
3.9
AI11816
Note:
Dimensions shown are in millimeters (mm).
45/49
Package mechanical information
M41T93
Figure 23. SOX18 – 18-lead Plastic Small Outline, 300mils, embedded crystal
D
9
1
h x 45°
C
E
H
A
10
18
A2
ddd
A1
B
e
A1
α
L
SO-J
Note:
Drawing is not to scale.
Table 24. SOX18 – 18-lead Plastic SO, 300mils, embedded crystal, pkg. mech. data
mm
Min
inches
Min
Sym
Typ
Max
Typ
Max
A
A1
A2
B
–
2.44
0.15
2.29
0.41
0.20
11.56
–
2.69
0.31
2.39
0.51
0.31
11.66
0.10
7.67
–
–
0.096
0.006
0.090
0.016
0.008
0.455
–
0.106
0.012
0.094
0.020
0.012
0.459
0.004
0.302
–
–
–
–
–
–
–
C
–
–
D
11.61
0.457
ddd
E
–
–
–
7.57
–
–
0.298
–
e
1.27
–
0.050
H
10.16
0.51
0°
10.52
0.81
8°
–
–
–
0.400
0.020
0°
0.414
0.032
8°
L
–
α
–
N
18
18
46/49
M41T93
Part numbering
7
Part numbering
Table 25. Ordering information
Example:
M41T
93
R
QA
6
E
Device Family
M41T
Device Type
93
Operating Voltage
S = VCC = 3.00 to 5.5V
R = VCC = 2.70 to 5.5V
Z = VCC = 2.38 to 5.5V
Package
QA = QFN16 (4mm x 4mm)
MY(1) = SOX18
Temperature Range
6 = –40°C to 85°C
Shipping Method
E = ECOPACK Package, Tubes
F = ECOPACK Package, Tape & Reel
1. The SOX18 package includes an embedded 32,768Hz crystal. Contact local ST sales office for availability.
For other options, or for more information on any aspect of this device, please contact the ST Sales
Office nearest you.
47/49
Revision history
M41T93
8
Revision history
Table 26. Revision history
Date
Revision
Changes
07-Aug-2006
1
Initial release.
48/49
M41T93
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
49/49
相关型号：
©2020 ICPDF网 联系我们和版权申明