概述
数据手册M48TMH1 概述
5V PC REAL TIME CLOCK 5V PC实时时钟
M48TMH1 数据手册
通过下载M48TMH1数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载M48T86
5V PC REAL TIME CLOCK
■ DROP-IN REPLACEMENT for PC
SNAPHAT (SH)
Battery/Crystal
COMPUTER CLOCK/CALENDAR
■ COUNTS SECONDS, MINUTES, HOURS,
DAYS, DAY of the WEEK, DATE, MONTH and
YEAR with LEAP YEAR COMPENSATION
■ INTERFACED WITH SOFTWARE AS 128
RAM LOCATIONS:
– 14 Bytes of Clock and Control Registers
– 114 Bytes of General Purpose RAM
24
28
1
1
■ SELECTABLE BUS TIMING (Intel/Motorola)
PCDIP24 (PC)
Battery/Crystal
■ THREE INTERRUPTS are SEPARATELY
SOH28 (MH)
CAPHAT
SOFTWARE-MASKABLE and TESTABLE
– Time-of-Day Alarm (Once/Second to
Once/Day)
– Periodic Rates from 122µs to 500ms
– End-of-Clock Update Cycle
Figure 1. Logic Diagram
■ PROGRAMMABLE SQUARE WAVE OUTPUT
■ SELF-CONTAINED BATTERY and CRYSTAL
in the CAPHAT DIP PACKAGE
V
CC
■ PACKAGING INCLUDES a 28-LEAD SOIC
®
and SNAPHAT TOP
(to be Ordered Separately)
8
■ SOIC PACKAGE PROVIDES DIRECT
CONNECTION for a SNAPHAT TOP
CONTAINS the BATTERY and CRYSTAL
AD0-AD7
SQW
IRQ
E
R/W
DS
■ PIN and FUNCTION COMPATIBLE with
bq3285/7A and DS128887
M48T86
AS
RST
RCL
MOT
V
SS
AI01640
May 2000
1/23
M48T86
Figure 2. DIP Connections
Figure 3. SOIC Connections
NC
MOT
NC
1
28
27
NC
V
MOT
NC
1
2
3
4
5
6
7
8
9
24
V
CC
2
CC
23 SQW
22 NC
21 RCL
20 NC
19 IRQ
18 RST
17 DS
16 NC
15 R/W
14 AS
3
26
SQW
NC
NC
4
25
NC
AD0
AD1
AD2
AD3
AD4
AD5
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
5
24
RCL
NC
6
23
7
22
IRQ
RST
DS
M48T86
M48T86
8
21
9
20
10
11
12
13
14
19
NC
AD6 10
AD7 11
18
R/W
AS
17
V
12
13
E
V
16
E
SS
SS
V
15
NC
AI01641
SS
AI01642
Table 1. Signal Names
DESCRIPTION
The M48T86 is an industry standard real time
clock (RTC).The M48T86 is composed of a lithium
energy source, quartz crystal, write-protection cir-
cuitry, and a 128 byte RAM array. This provides
the user with a complete subsystem packaged in
either a 24-pin DIP CAPHAT or 28-pin SNAPHAT
SOIC. Functions available to the user include a
non-volatile time-of-day clock, alarm interrupts, a
one-hundred-year clock with programmable inter-
rupts, square wave output, and 128 bytes of non-
volatile static RAM.
The 24 pin 600mil DIP CAPHAT™ houses the
M48T86 silicon with a quartz crystal and a long life
lithium button cell in a single package.
The 28 pin 330mil SOIC provides sockets with
gold plated contacts at both ends for direct con-
nection to a separate SNAPHAT housing contain-
ing the battery and crystal. The unique design
allows the SNAPHAT battery package to be
mounted on top of the SOIC package after the
completion of the surface mount process.
AD0-AD7
E
Multiplexed Address/Data Bus
Chip Enable Input
Write Enable Input
Data Strobe Input
Address Strobe Input
Reset Input
R/W
DS
AS
RST
RCL
MOT
SQW
IRQ
RAM Clear Input
Bus Type Select Input
Square Wave Output
Interrupt Request Output
Supply Voltage
V
CC
Insertion of the SNAPHAT housing after reflow
prevents potential battery and crystal damage due
to the high temperatures required for device sur-
face-mounting. The SNAPHAT housing is keyed
to prevent reverse insertion.
V
Ground
SS
NC
Not Connected Internally
The SOIC and battery packages are shipped sep-
arately in plastic anti-static tubes or in Tape & Reel
form.
2/23
M48T86
(1)
Table 2. Absolute Maximum Ratings
Symbol
Parameter
Value
0 to 70
Unit
°C
T
A
Ambient Operating Temperature
T
Storage Temperature (V Off, Oscillator Off)
–40 to 85
°C
STG
CC
(2)
Lead Solder Temperature for 10 seconds
Input or Output Voltages
Supply Voltage
260
–0.3 to 7.0
–0.3 to 7.0
1
°C
V
T
SLD
V
IO
V
V
CC
P
Power Dissipation
W
D
Note: 1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other conditions above those indicated in the operational section
of this specification is not implied. Exposure to the absolute maximum rating conditions for extended periods of time may affect
reliability.
2. Soldering temperature not to exceed 260°C for 10 seconds (total thermal budget not to exceed 150°C for longer than 30 seconds).
CAUTION: Negative undershoots below –0.3V are not allowed on any pin while in the Battery Back-up mode.
CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets.
For the 28 lead SOIC, the battery/crystal package
part number is "M4T28-BR12SH1".
Automatic deselection of the device provides in-
surance that data integrity is not compromised
AD0-AD7 (Multiplexed Bi-Directional Address/
Data Bus). The M48T86 provides a multiplexed
bus in which address and data information share
the same signal path. The bus cycle consists of
two stages; first the address is latched, followed by
the data. Address/Data multiplexing does not slow
the access time of the M48T86, since the bus
change from address to data occurs during the in-
ternal RAM access time. Addresses must be valid
prior to the falling edge of AS, at which time the
M48T86 latches the address present on AD0-
AD7. Valid write data must be present and held
stable during the latter portion of the R/W pulse. In
a read cycle, the M48T86 outputs 8 bits of data
during the latter portion of the DS pulse. The read
cycle is terminated and the bus returns to a high
impedance state upon a high transition on R/W.
should V
lect Voltage (V
fall below specified Power-fail Dese-
CC
) levels. The automatic deselec-
PFD
tion of the device remains in effect upon power up
for a period of 200ms (max) after V rises above
CC
V
, provided that the Real Time Clock is running
PFD
and the count down chain is not reset. This allows
sufficient time for V to stabilize and gives the
CC
system clock a wake up period so that a valid sys-
tem reset can be established.
The block diagram in Figure 3 shows the pin con-
nections and the major internal functions of the
M48T86.
AS (Address Strobe Input). A positive going
pulse on the Address Strobe (AS) input serves to
demultiplex the bus. The falling edge of AS causes
the address present on AD0-AD7 to be latched
within the M48T86.
MOT (Mode Select). The MOT pin offers the flex-
ibility to choose between two bus types. When
SIGNAL DESCRIPTION
V
, V . DC power is provided to the device on
SS
CC
these pins.The M48T86 utilizes a 5V V
SQW (Square Wave Output). During normal op-
.
CC
eration (i.e. valid V ), the SQW pin can output a
CC
signal from one of 13 taps.The frequency of the
SQW pin can be changed by programming Regis-
ter A as shown in Table 10. The SQW signal can
be turned on and off using the SQWE bit (Register
B; bit 3). The SQW signal is not available when
connected to V , Motorola bus timing is selected.
CC
When connected to V or left disconnected, Intel
SS
bus timing is selected. The pin has an internal pull-
down resistance of approximately 20K ohms.
V
is less than V
.
CC
PFD
3/23
M48T86
Figure 4. Block Diagram
OSCILLATOR
/ 8
/ 64
/ 64
PERIODIC INTERRUPT/SQUARE WAVE SELECTOR
E
POWER
SWITCH
AND
V
CC
V
POK
CC
WRITE
V
SQUARE WAVE
OUTPUT
PROTECT
BAT
SQW
IRQ
RST
REGISTERS A,B,C,D
CLOCK CALENDAR,
CLOCK/
CALENDAR
UPDATE
AND ALARM RAM
DOUBLE
BUFFERED
DS
R/W
AS
BCD/BINARY
INCREMENT
RCL
BUS
INTERFACE
STORAGE
REGISTERS
(114 BYTES)
AD0-AD7
AI01643
DS (Data Strobe Input). The DS pin is also re-
ferred to as Read (RD). A falling edge transition on
the Data Strobe (DS) input enables the output dur-
ing a a read cycle. This is very similar to an Output
Enable (G) signal on other memory devices.
E (Chip Enable Input). The Chip Enable pin
must be asserted low for a bus cycle in the
M48T86 to be accessed. Bus cycles which take
place without asserting E will latch the addresses
present, but no data access will occur.
IRQ (Interrupt Request Output). The IRQ pin is
an open drain output that can be used as an inter-
rupt input to a processor. The IRQ output remains
low as long as the status bit causing the interrupt
is present and the corresponding interrupt-enable
bit is set. IRQ returns to a high impedance state
whenever Register C is read. The RST pin can
also be used to clear pending interrupts. Because
the IRQ bus is an open drain output, it requires an
external pull-up resistor to V
.
CC
4/23
M48T86
RST (Reset Input). The M48T86 is reset when
the RST input is pulled low. With a valid V ap-
plied and a low on RST, the following events oc-
cur:
1. Periodic Interrupt Enable (PIE) bit is cleared to
a zero. (Register B; Bit 6)
2. Alarm Interrupt Enable (AIE) bit is cleared to a
zero.(Register B; bit 5)
RCL (RAM Clear). The RCL pin is used to clear
all 114 storage bytes, excluding clock and control
registers, of the array to FF(hex) value. The array
will be cleared when the RCL pin is held low for at
least 100ms with the oscillator running. Usage of
this pin does not affect battery load. This function
CC
is applicable only when V
is applied.
CC
R/W (Read/Write Input). The R/W pin is utilized
to latch data into the M48T86 and provides func-
tionality similar to W in other memory systems.
3. Update Ended Interrupt Request (UF) bit is
cleared to a zero. (Register C; Bit 4)
4. Interrupt Request (IRQF) bit is cleared to a zero.
(Register C Bit 7)
5. Periodic Interrupt Flag (PF) bit is cleared to a
zero. (Register C; Bit 6)
6. The device is not accessible until RST is re-
turned high.
7. Alarm Interrupt Flag (AF) bit is cleared to a zero.
(Register C; Bit 5)
ADDRESS MAP
The address map of the M48T86 is shown in Fig-
ure 9. It consists of 114 bytes of user RAM, 10
bytes of RAM that contain the RTC time, calendar
and alarm data, and 4 bytes which are used for
control and status. All bytes can be read or written
to except for the following:
1. Registers C & D are read-only.
2. Bit 7 of Register A is read-only.
8. The IRQ pin is in the high impedance state.
The contents of the four Registers A, B, C, and D
are described in the "Registers" section.
9. Square Wave Output Enable (SQWE) bit is
cleared to zero. (Register B; Bit 3).
10.Update Ended Interrupt Enable (UIE) is cleared
to a zero. (Register B; Bit 4)
5/23
M48T86
Table 3. Time, Calendar and Alarm Formats
Range
Binary
00-3B
00-3B
00-3B
00-3B
Address
RTC Bytes
Decimal
0-59
BCD
00-59
00-59
00-59
00-59
0
1
2
3
Seconds
Seconds Alarm
Minutes
0-59
0-59
Minutes Alarm
0-59
01-0C AM
81-8C PM
01-12 AM
81-92 PM
Hours, 12-hrs
Hours, 24-hrs
1-12
0-23
1-12
4
5
00-17
00-23
01-0C AM
81-8C PM
01-12 AM
81-92 PM
Hours Alarm, 12-hrs
Hours Alarm, 24-hrs
Day of Week (1 = Sun)
Day of Month
Month
0-23
1-7
00-17
01-07
01-1F
01-0C
00-63
00-23
01-07
01-31
01-12
00-99
6
7
8
9
1-31
1-12
0-99
Year
TIME, CALENDAR, AND ALARM LOCATIONS
shows the binary and BCD formats of the time, cal-
endar, and alarm locations. The 24/12 bit (Regis-
ter B; Bit 1) cannot be changed without
reinitializing the hour locations. When the 12-hour
format is selected, a logic one in the high order bit
of the hours byte represents PM. The time, calen-
dar, and alarm bytes are always accessible be-
cause they are double buffered. Once per second
the ten bytes are advanced by one second and
checked for an alarm condition. If a read of the
time and calendar data occurs during an update, a
problem exists where seconds, minutes, hours,
etc. may not correlate. However, the probability of
reading incorrect time and calendar data is low.
Methods of avoiding possible incorrect time and
calendar reads are reviewed later in this text.
The time and calendar information is obtained by
reading the appropriate memory bytes. The time,
calendar, and alarm registers are set or initialized
by writing the appropriate RAM bytes. The con-
tents of the time, calendar, and alarm bytes can be
either Binary or Binary-Coded Decimal (BCD) for-
mat. Before writing the internal time, calendar, and
alarm register, the SET bit (Register B; Bit 7)
should be written to a logic "1". This will prevent
updates from occurring while access is being at-
tempted. In addition to writing the time, calendar,
and alarm registers in a selected format (binary or
BCD), the Data Mode (DM) bit (Register B; Bit 2),
must be set to the appropriate logic level ("1" sig-
nifies binary data; "0" signifies Binary Coded Dec-
imal (BCD data). All time, calendar, and alarm
bytes must use the same data mode. The SET bit
should be cleared after the Data Mode bit has
been written to allow the Real Time Clock to up-
date the time and calendar bytes. Once initialized,
the Real Time Clock makes all updates in the se-
lected mode. The data mode cannot be changed
without reinitializing the ten data bytes. Table 3
NON-VOLATILE RAM
The 114 general purpose non-volatile RAM bytes
are not dedicated to any special function within the
M48T86. They can be used by the processor pro-
gram as non-volatile memory and are fully acces-
sible during the update cycle.
6/23
M48T86
Figure 5. AC Testing Load Circuit
Figure 6. AC Testing Load Circuit
5V
5V
960Ω
1.15kΩ
FOR ALL
OUTPUTS
EXCEPT IRQ
IRQ
510Ω
50pF
130pF
AI01644
AI01645
Table 4. AC Measurement Conditions
Input Rise and Fall Times
≤ 5ns
0 to 3V
1.5V
Input Pulse Voltages
Input and Output Timing Ref. Voltages
Note that Output Hi-Z is defined as the point where data is no longer driven.
(1, 2)
Table 5. Capacitance
(T = 25 °C, f = 1 MHz)
A
Symbol
Parameter
Input Capacitance
Test Condition
Min
Max
Unit
C
V
= 0V
= 0V
7
pF
IN
(3)
IN
V
OUT
Input / Output Capacitance
5
pF
C
IO
Note: 1. Effective capacitance measured with power supply at 5V.
2. Sampled only, not 100% tested.
3. Outputs deselected.
Table 6. DC Characteristics (1)
(T = 0 to 70 °C; V = 4.5V to 5.5V)
A
CC
Symbol
Parameter
Test Condition
Min
Max
Unit
(1)
0V ≤ V ≤ V
Input Leakage Current
±1
µA
I
LI
IN
CC
(1)
0V ≤ V
≤ V
CC
Output Leakage Current
Supply Current
±1
15
µA
mA
V
I
OUT
LO
I
Outputs open
CC
V
Input Low Voltage
Input High Voltage
Output Low Voltage
–0.3
2.2
0.8
IL
V
V
+ 0.3
V
IH
CC
I
= 4mA
0.4
0.4
V
OL
V
V
OL
I
= 0.5mA
= –1mA
OH
V
OL
Output Low Voltage (IRQ)
Output High Voltage
I
2.4
V
OH
Note: 1. Outputs deselected.
7/23
M48T86
(1)
Table 7. Power Down/Up Trip Points DC Characteristics
(T = 0 to 70 °C)
A
Symbol
Parameter
Power-fail Deselect Voltage
Min
Typ
Max
Unit
V
V
PFD
4.0
4.35
V
Battery Back-up Switchover Voltage
3.0
V
SO
(2)
Expected Data Retention Time
10
YEARS
t
DR
Note: 1. All voltages referenced to V
.
SS
2. At 25°C.
Table 8. Power Down/Up Mode AC Characteristics
(TA = 0 to 70°C)
Symbol
Parameter
Min
Max
Unit
µs
(1)
V
Fall Time
300
100
20
t
F
CC
t
V
V
Rise Time
to E High
µs
R
CC
t
200
ms
REC
PFD
Note: 1. V fall time of less than t may result in deselection/write protection not occurring until 200µs after V passes V .
PFD
CC
F
CC
Figure 7. Power Down/Up Mode AC Waveforms
V
4.5V
CC
V
PFD
V
SO
tF
tR
tREC
E
AI01646
INTERRUPTS
Register B enable the interrupts. Writing a logic "1"
to an interrupt-enable bit (Register B; Bit 6 = PIE;
Bit 5 = AIE; Bit 4 = UIE) permits an interrupt to be
initialized when the event occurs. A zero in an in-
terrupt-enable bit prohibits the IRQ pin from being
asserted from that interrupt condition. If an inter-
rupt flag is already set when an interrupt is en-
abled, IRQ is immediately set at an active level,
although the interrupt initiating the event may have
occurred much earlier. As a result, there are cases
where the program should clear such earlier initi-
ated interrupts before first enabling new interrupts.
The RTC plus RAM includes three separate, fully
automatic sources of interrupt (alarm, periodic, up-
date-in-progress) available to a processor. The
alarm interrupt can be programmed to occur at
rates from once per second to once per day. The
periodic interrupt can be selected from rates of
500ms to 122µs. The update-ended interrupt can
be used to indicate that an update cycle has com-
pleted.
The processor program can select which inter-
rupts, if any, are going to be used. Three bits in
8/23
M48T86
Table 9. AC Characteristics
(T = 0 to 70 °C; V = 4.5V to 5.5V)
A
CC
M48T86
Typ
Symbol
Parameter
Unit
Min
160
80
55
0
Max
t
Cycle Time
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
CYC
t
t
Pulse Width, Data Strobe Low or R/W High
Pulse Width, Data Strobe High or R/W Low
R/W Hold Time
DSL
DSH
RWH
t
t
R/W Setup Time
10
5
RWS
t
Chip Select Setup Time
CS
t
Chip Select Hold Time
0
CH
t
Read Data Hold Time
0
25
DHR
t
Write Data Hold Time
0
DHW
t
AS
Address Setup Time
20
5
t
AH
Address Hold Time
t
Delay Time, Data Strobe to Address Strobe Rise
Pulse Width Address Strobe High
Delay Time, Address Strobe to Data Strobe Rise
Output Data Delay Time from Data Strobe Rise
Write Setup Time
10
30
35
DAS
t
ASW
t
ASD
t
50
OD
t
30
DW
t
Delay Time before Update Cycle
Periodic Interrupt Time interval
Time of Update Cycle
244
–
BUC
(1)
PI
–
–
t
t
1
µs
UC
Note: 1. See Table 10.
When an interrupt event occurs, the related flag bit
(Register C; Bit 6 = PF; Bit 5 = AF; Bit 4 = UF) is
set to a logic "1". These flag bits are set indepen-
dent of the state of the corresponding enable bit in
Register B and can be used in a polling mode with-
out enabling the corresponding enable bits. The
interrupt flag bits are status bits which software
can interrogate as necessary.
When a flag is set, an indication is given to soft-
ware that an interrupt event has occurred since the
flag bit was last read; however, care should be tak-
en when using the flag bits as all are cleared each
time Register C is read. Double latching is includ-
ed with Register C so that bits which are set, re-
main stable throughout the read cycle. All bits
which are set high are cleared when read. Any
new interrupts which are pending during the read
cycle are held until after the cycle is completed.
One, two, or three bits can be set when reading
Register C. Each utilized flag bit should be exam-
ined when read to ensure that no interrupts are
lost.
The second flag bit usage method is with fully en-
abled interrupts. When an interrupt flag bit is set
and the corresponding enable bit is also set, the
IRQ pin is asserted low. IRQ is asserted as long as
at least one of the three interrupt sources has its
flag and enable bits both set. The IRQF bit (Regis-
ter C; Bit 7) is a "1" whenever the IRQ pin is being
driven low. Determination that the RTC initiated an
interrupt is accomplished by reading Register C.A
logic "1" in the IRQF bit indicates that one or more
interrupts have been initiated by the M48T86. The
act of reading Register C clears all active flag bits
and the IRQF bit.
9/23
M48T86
Figure 8. Intel Bus Read Mode AC Waveforms
tCYC
AS
tASW
tASD
DS
tDSL
R/W
tDAS
E
tDSH
tCS
tOD
tCH
tAS
tAH
tDHR
AD0-AD7
AI01647
Figure 9. Intel Bus Write AC Waveforms
tCYC
AS
tDAS
tASW
tDSL
tASD
DS
R/W
E
tDSH
tCS
tCH
tAS
tAH
tDW
tDHW
AD0-AD7
AI01648
10/23
M48T86
Figure 10. Motorola Bus Read/Write Mode AC Waveforms
AS
tDAS
tASW
tASD
tCYC
DS
tDSL
tRWS
tDSH
tRWH
R/W
E
tCS
tCH
tAH
tAS
tDW
tDHW
AD0-AD7
(Write)
tAS
tOD
tAH
tDHR
AD0-AD7
(Read)
AI01649
PERIODIC INTERRUPT
ALARM INTERRUPT
The periodic interrupt will cause the IRQ pin to go
to an active state from once every 500ms to once
every 122µs. This function is separate from the
alarm interrupt which can be output from once per
second to once per day. The periodic interrupt rate
is selected using the same Register A bits which
select the square wave frequency (see Table 10).
Changing the Register A bits affects both the
square wave frequency and the periodic interrupt
output. However, each function has a separate en-
able bit in Register B. The periodic interrupt is en-
abled by the PIE bit (Register B; Bit 6). The
periodic interrupt can be used with software
counters to measure inputs, create output inter-
vals, or await the next needed software function.
The alarm interrupt provides the system processor
with an interrupt when a match is made between
the RTC's hours, minutes, and seconds bytes and
the corresponding alarm bytes.
The three alarm bytes can be used in two ways.
First, when the alarm time is written in the appro-
priate hours, minutes, and seconds alarm loca-
tions, the alarm interrupt is initiated at the specified
time each day if the Alarm Interrupt Enable bit
(Register B; Bit 5) is high. The second use is to in-
sert a "don't care" state in one or more of the three
alarm bytes. The "don't care" code is any hexadec-
imal value from C0 to FF. The two most significant
bits of each byte set the "don't care" condition
when at logic "1". An alarm will be generated each
hour when the "don't care" is are set in the hours
byte. Similarly, an alarm is generated every minute
with "don't care" codes in the hour and minute
alarm bytes. The "don't care" codes in all three
alarm bytes create an interrupt every second.
11/23
M48T86
Figure 11. Address Map
0
00
0
1
SECONDS
SECONDS ALARM
MINUTES
14
BYTES
CLOCK AND CONTROL
STATUS REGISTERS
2
3
MINUTES ALARM
HOURS
13
14
0D
0E
BCD OR
BINARY
FORMAT
4
5
HOURS ALARM
DAY OF WEEK
DATE OF MONTH
MONTH
6
7
8
9
YEAR
114
BYTES
STORAGE REGISTERS
10
11
12
13
REGISTER A
REGISTER B
REGISTER C
REGISTER D
127
7F
AI01650
UPDATE CYCLE INTERRUPT
SQW frequency selection shares the 1-of-15 se-
lector with the periodic interrupt generator. Once
the frequency is selected, the output of the SQW
pin can be turned on and off under program control
with the square wave enabled (SQWE).
After each update cycle, the update cycle ended
flag bit (UF) (Register C; Bit 4) is set to a "1". If the
update interrupt enable bit (UIE) (Register B; Bit 4)
is set to a "1", and the SET bit (Register B; Bit 7) is
a "0", then an interrupt request is generated at the
end of each update cycle.
OSCILLATOR CONTROL BITS
When the M48T86 is shipped from the factory the
internal oscillator is turned off. This feature pre-
vents the lithium energy cell from being dis-
charged until it is installed in a system. A pattern of
"010" in Bits 4-6 of Register A will turn the oscilla-
tor on and enable the countdown chain. A pattern
of "11X" will turn the oscillator on, but holds the
countdown chain of the oscillator in reset. All other
combinations of Bits 4-6 keep the oscillator off.
SQUARE WAVE OUTPUT SELECTION
Thirteen of the 15 divider taps are made available
to a 1-of-15 selector, as shown in the block dia-
gram of Figure 3. The purpose of selecting a divid-
er tap is to generate a square wave output signal
on the SQW pin. The RS3-RS0 bits in Register A
establish the square wave output frequency.
These frequencies are listed in Table 10. The
12/23
M48T86
Table 10. Square Wave Frequency/Periodic Interrupt Rate
Register A Bits
RS2 RS1
Square Wave
Periodic Interrupt
RS3
0
RS0
0
Frequency
None
256
128
8.192
4.096
2.048
1.024
512
256
128
64
Units
Period
None
Units
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
Hz
Hz
3.90625
7.8125
122.070
244.141
488.281
976.5625
1.953125
3.90625
7.8125
15.625
31.25
ms
ms
us
0
0
0
1
kHz
kHz
kHz
kHz
Hz
0
0
us
0
1
us
0
0
us
0
1
ms
ms
ms
ms
ms
ms
ms
ms
ms
1
0
Hz
1
1
Hz
1
0
Hz
1
1
32
Hz
1
0
16
Hz
62.5
1
1
8
Hz
125
1
0
4
Hz
250
1
1
2
Hz
500
UPDATE CYCLE
read valid time and date information. If this inter-
rupt is used, the IRQF bit (Register C; Bit 7) should
be cleared before leaving the interrupt routine.
The M48T86 executes an update cycle once per
second regardless of the SET bit (Register B; Bit
7). When the SET bit is asserted, the user copy of
the double buffered time, calendar, and alarm
bytes is frozen and will not update as the time in-
crements. However, the time countdown chain
continues to update the internal copy of the buffer.
This feature allows accurate time to be main-
tained, independent of reading and writing the
time, calendar, and alarm buffers. This also guar-
antees that the time and calendar information will
be consistent. The update cycle also compares
each alarm byte with the corresponding time byte
and issues an alarm if a match or if a "don't care"
code is present in all three positions.
There are three methods of accessing the real
time clock that will avoid any possibility of obtain-
ing inconsistent time and calendar data. The first
method uses the update-ended interrupt. If en-
abled, an interrupt occurs after every update cycle
which indicates that over 999ms are available to
A second method uses the Update-In-Progress
(UIP) bit (Register A; Bit 7) to determine if the up-
date cycle is in progress. The UIP bit will pulse
once per second. After the UIP bit goes high, the
update transfer occurs 244µs later. If a low is read
on the UIP bit, the user has at least 244µs before
the time/calendar data will be changed. Therefore,
the user should avoid interrupt service routines
that would cause the time needed to read valid
time/calendar data to exceed 244µs.
The third method uses a periodic interrupt to deter-
mine if an update cycle is in progress. The UIP bit
is set high between the setting of the PF bit (Reg-
ister C; Bit 6). Periodic interrupts that occur at a
rate greater than t
allow valid time and date in-
BUC
formation to be reached at each occurrence of the
periodic interrupt.The reads should be completed
within 1/(t
+ t
) to ensure that data is not
PL/2
BUC
read during the update cycle.
13/23
M48T86
Figure 12. Update Period Timing and UIP
UPDATE PERIOD (1sec)
UIP
tBUC
tUC
AI01651
Figure 13. Update-ended/Periodic Interrupt Relationship
UPDATE PERIOD (1sec)
UIP
tBUC
tUC
tPI
tPI
tPI
PF
UF
AI01652B
14/23
M48T86
REGISTER A
MSB
BIT7
UIP
BIT6
BIT5
BIT4
BIT3
RS3
BIT2
RS2
BIT1
RS1
BIT0
RS0
OSC2
OSC1
OSC0
UIP. Update in Progress
RS3, RS2, RS1, RS0
The Update in Progress (UIP) bit is a status flag
that can be monitored. When the UIP bit is one,
the update transfer will soon occur. When UIP isa
zero, the update transfer will not occur for at least
244µs. The time, calendar, and alarm information
in RAM is fully available for access when the UIP
bit is zero. The UIP bit is read only and is not af-
fected by RST. Writing the SET bit in Register B to
a "1" inhibits any update transfer and clears the
UIP status bit.
These four rate-selection bits select one of the 13
taps on the 15-stage divider or disable the divider
output. The tap selected may be used to generate
an output square wave (SQW pin) and/or a period-
ic interrupt. The user may do one of the following:
1. Enable the interrupt with the PIE bit;
or
2. Enable the SQW output with the SQWE bit;
or
OSC0, OSC1, OSC2. Oscillator Control
3. Enable both at the same time and same rate;
These three bits are used to control the oscillator
and reset the countdown chain. A pattern of "010"
enables operation by turning on the oscillator and
enabling the divider chain. A pattern of 11X turns
the oscillator on, but keeps the frequency divider
disabled. When "010" is written, the first update
begins after 500ms.
or
4. Enable neither.
Table 10 lists the periodic interrupt rates and the
square wave frequencies that may be chosen with
the RS bits. These four read/write bits are not af-
fected by RST.
15/23
M48T86
REGISTER B
MSB
BIT7
SET
BIT6
PIE
BIT5
AIE
BIT4
UIE
BIT3
BIT2
DM
BIT1
BIT0
DSE
SQWE
24/12
SET
SQWE. Square Wave Enable
When the SET bit is a zero, the update transfer
functions normally by advancing the counts once
per second. When the SET bit is written to a one,
any update transfer is inhibited and the program
may initialize the time and calendar bytes without
an update occurring. Read cycles can be executed
in a similar manner. SET is a read/write bit which
is not modified by RST or internal functions of the
M48T86.
When the Square Wave Enable (SQWE) bit is set
to a one, a square wave signal is driven out on the
SQW pin. The frequency is determined by the
rate-selection bits RS3-RS0. When the SQWE bit
is set to zero, the SQW pin is held low. The SQWE
bit is cleared by the RST pin. SQWE is a read/write
bit.
DM. Data Mode
The Data Mode (DM) bit indicates whether time
and calendar information are in binary or BCD for-
mat. The DM bit is set by the program to the appro-
priate format and can be read as required. This bit
is not modified by internal function or RST. A one
in DM signifies binary data and a zero specifies Bi-
nary Coded Decimal (BCD) data.
PIE. Periodic Interrupt Enable
The Periodic Interrupt Enable bit (PIE) is a read/
write bit which allows the Periodic Interrupt Flag
(PF) bit Register C to cause the IRQ pin to be driv-
en low. When the PIE bit is set to one, periodic in-
terrupts are generated by driving the IRQ pin low
at a rate specified by the RS3-RS0 bits of Register
A. A zero in the PIE bit blocks the IRQ output from
being driven by a periodic interrupt, but the Period-
ic Flag (PF) bit is still set at the periodic rate. PIE
is not modified by any internal M48T86 functions,
but is cleared to zero on RST.
24/12
The 24/12 control bit establishes the format of the
hours byte.A one indicates the 24-hour mode and
a zero indicates the 12-hour mode. This bit is read/
write and is not affected by internal functions or
RST.
AIE. Alarm Interrupt Enable
DSE. Daylight Savings Enable
The Alarm Interrupt Enable (AIE) bit is a Read/
Write bit which, when set to a one, permits the
Alarm Flag (AF) bit in Register C to assert IRQ. An
alarm interrupt occurs for each second that the
three time bytes equal the three alarm bytes in-
cluding a "don’t care" alarm code of binary
1XXXXXXX. When the AIE bit is set to zero, the
AF bit does not initiate the IRQ signal. The RST
pin clears AIE to zero. The internal functions of the
M48T86 do not affect the AIE bit.
The Daylight Savings Enable (DSE) bit is a read/
write bit which enables two special updates when
set to a one. On the first Sunday in April, the time
increments from 1:59:59AM to 3:00:00 AM. On the
last Sunday in October, when the time reaches
1:59:59 AM, it changes to 1:00:00 AM. These spe-
cial updates do not occur when the DSE bit is a ze-
ro. This bit is not affected by internal functions or
RST.
UIE. Update Ended Interrupt Enable
The Update Ended Interrupt Enable (UIE) bit is a
read/write bit which enables the Update End Flag
(UF) bit in Register C to assert IRQ. A transition
low on the RST pin or the SET bit going high clears
the UIE bit.
16/23
M48T86
REGISTER C
MSB
BIT7
BIT6
PF
BIT5
AF
BIT4
UF
BIT3
0
BIT2
0
BIT1
0
BIT0
0
IRQF
IRQF. Interrupt Request Flag
AF. Alarm Flag
The Interrupt Request Flag (IRQF) bit is set to a
one when one or more of the following are true:
PF = PIE = 1
AF = AIE = 1
UF = UIE = 1
A one in the AF (Alarm Interrupt Flag) bit indicates
that the current time has matched the alarm time.
If the AIE bit is also a one, the IRQ pin will go low
and a one will appear in the IRQF bit. A RST or a
read of Register C will clear AF.
UF. Update Ended Interrupt Flag
(i.e. IRQF = PF*PIE+AF*AIE+UF*UIE)
PF. Periodic Interrupt Flag
The Update Ended Interrupt Flag (UF) bit is set af-
ter each update cycle. When the UIE bit is set to a
one, the one in the UF bit causes the IRQF bit to
be a one. This will assert the IRQ pin. UF is
cleared by reading Register C or an RST.
BIT 0 through 3. Unused Bits
Bit 3-Bit 0 are unused. These bits always read
zero and cannot be written.
The Periodic Interrupt Flag (PF) is a read-only bit
which is set to a one when an edge is detected on
the selected tap of the divider chain. The RS3-RS0
bits establish the periodic rate. PF is set to a one
independent of the state of the PIE bit. The IRQ
signal is active and will set the IRQF bit. The PF bit
is cleared by a RST or a software read of Register
C.
REGISTER D
MSB
BIT7
VRT
BIT6
0
BIT5
0
BIT4
0
BIT3
0
BIT2
0
BIT1
0
BIT0
0
VRT. Valid Ram And Time
BIT 0 through 6. Unused Bits
The Valid RAM and Time (VRT) bit is set to the
one state by STMicroelectronics prior to shipment.
This bit is not writable and should always be a one
when read. If a zero is ever present, an exhausted
internal lithium cell is indicated and both the con-
tents of the RTC data and RAM data are question-
able. This bit is unaffected by RST.
The remaining bits of Register D are not usable.
They cannot be written and when read, they will al-
ways read zero.
17/23
M48T86
POWER SUPPLY DECOUPLING
and UNDERSHOOT PROTECTION
Figure 14. Supply Voltage Protection
I
transients, including those produced by output
CC
switching, can produce voltage fluctuations, re-
sulting in spikes on the V bus. These transients
CC
can be reduced if capacitors are used to store en-
ergy, which stabilizes the V
bus. The energy
CC
V
stored in the bypass capacitors will be released as
low going spikes are generated or energy will be
absorbed when overshoots occur. A ceramic by-
pass capacitor value of 0.1µF (as shown in Figure
14) is recommended in order to provide the need-
ed filtering.
CC
V
CC
0.1µF
DEVICE
In addition to transients that are caused by normal
SRAM operation, power cycling can generate neg-
V
ative voltage spikes on V
that drive it to values
SS
CC
below V by as much as one Volt. These nega-
SS
tive spikes can cause data corruption in the SRAM
while in battery backup mode. To protect from
these voltage spikes, it is recommended to con-
AI02169
nect a schottky diode from V
to V (cathode
CC
SS
connected to V , anode to V ). Schottky diode
CC
SS
1N5817 is recommended for through hole and
MBRS120T3 is recommended for surface mount.
18/23
M48T86
Table 11. Ordering Information Scheme
Example:
M48T86
MH
1
TR
Device Type
M48T
Package
PC = PCDIP24
(1)
MH
= SOH28
Temperature Range
1 = 0 to 70 °C
Shipping Method for SOIC
blank = Tubes
TR = Tape & Reel
Note: 1. The SOIC package (SOH28) requires the battery/crystal package (SNAPHAT) which is ordered separately under the part number
"M4T28-BR12SH1" in plastic tube or "M4T28-BR12SH1TR" in Tape & Reel form.
Caution: Do not place the SNAPHAT battery/crystal package "M4T28-BR12SH1" in conductive foam since will drain the lithium button-cell
battery.
For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de-
vice, please contact the ST Sales Office nearest to you.
Table 12. Revision History
Date
March 1999
05/04/00
Revision Details
First Issue
Page layout changed
19/23
M48T86
Table 13. PCDIP24 - 24 pin Plastic DIP, battery CAPHAT, Package Mechanical Data
mm
Min
inches
Min
Symb
Typ
Max
9.65
0.76
8.89
053
Typ
Max
A
A1
A2
B
8.89
0.38
8.36
0.38
1.14
0.20
34.29
17.83
2.29
25.15
15.24
3.05
24
0.3500
0.0150
0.3291
0.0150
0.0449
0.0079
1.3500
0.7020
0.0902
0.9902
0.6000
0.1201
24
0.3799
0.0299
0.3500
0.0209
0.0701
0.0122
1.3701
0.7220
0.1098
1.2098
0.6299
0.1500
B1
C
1.78
0.31
34.80
18.34
2.79
30.73
16.00
3.81
D
E
e1
e3
eA
L
N
Figure 15. PCDIP28 - 28 pin Plastic DIP, battery CAPHAT, Package Outline
A2
A
L
A1
e1
C
B1
B
eA
e3
D
N
1
E
PCDIP
Drawing is not to scale.
20/23
M48T86
Table 14. SOH28 - 28 lead Plastic Small Outline, 4-socket battery SNAPHAT, Package Mechanical Data
mm
Min
inches
Min
Symb
Typ
Max
3.05
0.36
2.69
0.51
0.32
18.49
8.89
–
Typ
Max
0.1201
0.0142
0.1059
0.0201
0.0126
0.7280
0.3500
–
A
A1
A2
B
0.05
2.34
0.36
0.15
17.71
8.23
–
0.0020
0.0921
0.0142
0.0059
0.6972
0.3240
–
C
D
E
e
1.27
0.0500
eB
H
3.20
11.51
0.41
0°
3.61
12.70
1.27
8°
0.1260
0.4531
0.0161
0°
0.1421
0.5000
0.0500
8°
L
α
N
28
28
CP
0.10
0.0039
Figure 16. SOH28 - 28 lead Plastic Small Outline, 4-socket battery SNAPHAT, Package Outline
A2
A
C
eB
B
e
CP
D
N
E
H
A1
α
L
1
SOH-A
Drawing is not to scale.
21/23
M48T86
Table 15. M4T28-BR12SH - SNAPHAT Housing for 48 mAh Battery & Crystal, Package Mechanical Data
mm
Min
inches
Min
Symb
Typ
Max
9.78
7.24
6.99
0.38
0.56
21.84
14.99
15.95
3.61
2.29
Typ
Max
A
A1
A2
A3
B
0.3850
0.2850
0.2752
0.0150
0.0220
0.8598
0.5902
0.6280
0.1421
0.0902
6.73
6.48
0.2650
0.2551
0.46
21.21
14.22
15.55
3.20
0.0181
0.8350
0.5598
0.6122
0.1260
0.0799
D
E
eA
eB
L
2.03
Figure 17. M4T28-BR12SH - SNAPHAT Housing for 48 mAh Battery & Crystal, Package Outline
A2
A1
A
A3
L
eA
D
B
eB
E
SH
Drawing is not to scale.
22/23
M48T86
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is registered trademark of STMicroelectronics
© 2000 STMicroelectronics - All Rights Reserved
All other names are the property of their respective owners.
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco -
Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
23/23
M48TMH1 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| M48TMH1TR | STMICROELECTRONICS | 5V PC REAL TIME CLOCK | 获取价格 |
|
| M48TPC1 | STMICROELECTRONICS | 5V PC REAL TIME CLOCK | 获取价格 |
|
| M48TPC1TR | STMICROELECTRONICS | 5V PC REAL TIME CLOCK | 获取价格 |
|
| M48TV-70MH1 | STMICROELECTRONICS | 3.3V-5V TIMEKEEPER CONTROLLER | 获取价格 |
|
| M48TV-70MH1TR | STMICROELECTRONICS | 3.3V-5V TIMEKEEPER CONTROLLER | 获取价格 |
|
| M48TV-70PM1 | STMICROELECTRONICS | 3.3V-5V 1 Mbit 128Kb x8 TIMEKEEPER SRAM | 获取价格 |
|
| M48TV-85MH1 | STMICROELECTRONICS | 3.3V-5V TIMEKEEPER CONTROLLER | 获取价格 |
|
| M48TV-85MH1TR | STMICROELECTRONICS | 3.3V-5V TIMEKEEPER CONTROLLER | 获取价格 |
|
| M48TV-85PM1 | STMICROELECTRONICS | 3.3V-5V 1 Mbit 128Kb x8 TIMEKEEPER SRAM | 获取价格 |
|
| M48TY-70MH1 | STMICROELECTRONICS | 3.3V-5V TIMEKEEPER CONTROLLER | 获取价格 |
|
M48TMH1 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 6
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 9
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
