M74HC75RM13TR [STMICROELECTRONICS]
4 BIT D TYPE LATCH; 4位D型锁存器
| 型号： | M74HC75RM13TR |
| 厂家： | 
ST |
| 描述： | 4 BIT D TYPE LATCH |
| 文件： | 总10页 (文件大小：271K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
M74HC75
4 BIT D TYPE LATCH
■
■
■
■
■
■
■
HIGH SPEED :
= 11ns (TYP.) at V = 6V
t
PD
CC
LOW POWER DISSIPATION:
=2µA(MAX.) at T =25°C
I
CC
A
HIGH NOISE IMMUNITY:
= V = 28 % V (MIN.)
V
NIH
NIL
CC
DIP
SOP
TSSOP
T & R
SYMMETRICAL OUTPUT IMPEDANCE:
|I | = I = 4mA (MIN)
OH
OL
BALANCED PROPAGATION DELAYS:
t
t
ORDER CODES
PACKAGE
PLH
PHL
WIDE OPERATING VOLTAGE RANGE:
(OPR) = 2V to 6V
TUBE
V
CC
DIP
SOP
M74HC75B1R
M74HC75M1R
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 75
M74HC75RM13TR
M74HC75TTR
TSSOP
DESCRIPTION
The M74HC75 is an high speed CMOS 4 BIT D
TYPE LATCH fabricated with silicon gate C MOS
technology.
It contains two groups of 2 bit latches controlled by
an enable input (G1•2 or G3•4). These two latch
groups can be used in different circuits. Each latch
has Q and Q outputs (1Q - 4Q and 1Q - 4Q). The
data applied to the data input is transferred to the
Q and Q outputs when the enable input is taken
high and the outputs will follow the data input as
long as the enable input is kept high. When the
enable input is taken low, the information data
applied to the data input is retained at the outputs.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
2
PIN CONNECTION AND IEC LOGIC SYMBOLS
August 2001
1/10
M74HC75
IINPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN No
SYMBOL
NAME AND FUNCTION
Complementary Latch
Outputs
1, 14, 11, 8
2, 3, 6, 7
4
1Q to 4Q
1D to 4D
G3 • 4
Data Inputs
Latch Enable Input,
latches 3 and 4
Latch Enable Input,
latches 1 and 2
13
G1 • 2
16, 15, 10, 9
1Q to 4Q
GND
Latch Outputs
12
5
Ground (0V)
V
Positive Supply Voltage
CC
TRUTH TABLE
INPUTS
OUTPUTS
FUNCTION
D
G
Q
Q
L
H
X
H
H
L
L
H
H
L
Qn
Qn
LATCH
LOGIC DIAGRAM
2/10
M74HC75
ABSOLUTE MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
V
Supply Voltage
-0.5 to +7
V
V
CC
V
DC Input Voltage
-0.5 to V + 0.5
I
CC
V
DC Output Voltage
DC Input Diode Current
DC Output Diode Current
DC Output Current
-0.5 to V + 0.5
V
O
CC
I
± 20
± 20
mA
mA
mA
mA
mW
°C
IK
I
OK
I
± 25
O
I
or I
DC V
or Ground Current
CC
± 50
CC
GND
P
Power Dissipation
500(*)
-65 to +150
300
D
T
Storage Temperature
Lead Temperature (10 sec)
stg
T
°C
L
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Value
Unit
V
Supply Voltage
2 to 6
0 to V
V
V
CC
V
Input Voltage
I
CC
V
Output Voltage
0 to V
CC
V
O
T
Operating Temperature
Input Rise and Fall Time
-55 to 125
0 to 1000
0 to 500
0 to 400
°C
ns
ns
ns
op
V
V
V
= 2.0V
= 4.5V
= 6.0V
CC
CC
CC
t , t
r
f
3/10
M74HC75
DC SPECIFICATIONS
Test Condition
Value
T
= 25°C
Symbol
Parameter
-40 to 85°C -55 to 125°C Unit
A
V
CC
(V)
Min. Typ. Max. Min. Max. Min. Max.
V
High Level Input
Voltage
2.0
4.5
6.0
2.0
4.5
6.0
2.0
1.5
3.15
4.2
1.5
3.15
4.2
1.5
3.15
4.2
IH
V
V
V
Low Level Input
Voltage
0.5
1.35
1.8
0.5
1.35
1.8
0.5
1.35
1.8
IL
V
High Level Output
Voltage
I =-20 µA
1.9
4.4
5.9
2.0
4.5
6.0
1.9
4.4
1.9
4.4
OH
O
I =-20 µA
4.5
6.0
4.5
6.0
2.0
4.5
6.0
4.5
6.0
O
I =-20 µA
5.9
5.9
V
V
O
I =-4.0 mA
4.18 4.31
4.13
5.63
4.10
5.60
O
I =-5.2 mA
5.68
5.8
0.0
0.0
0.0
O
V
Low Level Output
Voltage
I =20 µA
0.1
0.1
0.1
0.1
0.1
0.1
0.1
OL
O
I =20 µA
O
I =20 µA
0.1
0.1
O
I =4.0 mA
0.17 0.26
0.18 0.26
0.33
0.33
0.40
0.40
O
I =5.2 mA
O
I
Input Leakage
Current
I
V = V
or GND
6.0
6.0
± 0.1
± 1
± 1
µA
µA
I
CC
CC
I
Quiescent Supply
Current
CC
V = V
or GND
2
20
40
I
4/10
M74HC75
AC ELECTRICAL CHARACTERISTICS (C = 50 pF, Input t = t = 6ns)
L
r
f
Test Condition
Value
-40 to 85°C -55 to 125°C Unit
T
= 25°C
Symbol
Parameter
A
V
CC
(V)
Min. Typ. Max. Min. Max. Min. Max.
t
t
Output Transition
Time
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
25
7
75
15
13
110
22
19
125
25
21
75
15
13
50
10
9
95
19
16
140
28
24
155
31
26
95
19
16
65
13
11
30
6
110
22
19
165
33
28
190
38
32
110
22
19
75
15
13
40
8
TLH THL
ns
ns
ns
ns
ns
ns
6
t
t
t
Propagation Delay
Time (DATA - Q)
36
12
10
40
13
11
18
6
PLH PHL
t
Propagation Delay
Time (G-Q)
PLH PHL
t
Minimum Pulse
Width (G)
W(H)
6
t
t
Minimum Set-up
Time
s
Minimum Hold
Time
25
5
h
4
5
7
CAPACITIVE CHARACTERISTICS
Test Condition
Value
-40 to 85°C -55 to 125°C Unit
T
= 25°C
Symbol
Parameter
A
V
CC
(V)
Min. Typ. Max. Min. Max. Min. Max.
C
Input Capacitance
5.0
5
10
10
10
pF
pF
IN
C
Power Dissipation
Capacitance (note
1)
PD
5.0
30
1) C is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
PD
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I
= C x V x f + I
CC(opr)
PD CC IN CC
5/10
M74HC75
TEST CIRCUIT
C
R
= 50pF or equivalent (includes jig and probe capacitance)
L
T
= Z
of pulse generator (typically 50Ω)
OUT
SWITCHING CHARACTERISTICS TEST WAWEFORM (f=1MHz; 50% duty cycle)
6/10
M74HC75
Plastic DIP-16 (0.25) MECHANICAL DATA
mm.
TYP
inch
TYP.
DIM.
MIN.
0.51
0.77
MAX.
MIN.
0.020
0.030
MAX.
a1
B
b
1.65
0.065
0.5
0.020
0.010
b1
D
E
e
0.25
20
0.787
8.5
2.54
17.78
0.335
0.100
0.700
e3
F
7.1
5.1
0.280
0.201
I
L
3.3
0.130
Z
1.27
0.050
P001C
7/10
M74HC75
SO-16 MECHANICAL DATA
mm.
inch
TYP.
DIM.
MIN.
TYP
MAX.
1.75
0.2
MIN.
MAX.
0.068
0.007
0.064
0.018
0.010
A
a1
a2
b
0.1
0.003
1.65
0.46
0.25
0.35
0.19
0.013
0.007
b1
C
0.5
0.019
c1
D
45° (typ.)
9.8
5.8
10
0.385
0.228
0.393
0.244
E
6.2
e
1.27
8.89
0.050
0.350
e3
F
3.8
4.6
0.5
4.0
5.3
0.149
0.181
0.019
0.157
0.208
0.050
0.024
G
L
1.27
0.62
M
S
8° (max.)
PO13H
8/10
M74HC75
TSSOP16 MECHANICAL DATA
mm.
inch
TYP.
DIM.
MIN.
TYP
MAX.
1.2
MIN.
MAX.
0.047
0.006
0.041
0.012
0.0089
0.201
0.260
0.176
A
A1
A2
b
0.05
0.8
0.15
1.05
0.30
0.20
5.1
0.002
0.031
0.007
0.004
0.193
0.244
0.169
0.004
0.039
1
0.19
0.09
4.9
c
D
5
6.4
0.197
0.252
E
6.2
6.6
E1
e
4.3
4.4
4.48
0.173
0.65 BSC
0.0256 BSC
K
0°
8°
0°
8°
L
0.45
0.60
0.75
0.018
0.024
0.030
A2
A
K
L
b
e
A1
c
E
D
E1
PIN 1 IDENTIFICATION
1
0080338D
9/10
M74HC75
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2001 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
© http://www.st.com
10/10
相关型号：
M74HC7640
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
M74HC7640B1R
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
M74HC7640C1R
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
M74HC7640F1R
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
M74HC7640M1R
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
M74HC7643
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
M74HC7643B1R
OCTAL BUS TRANSCEIVER (3-STATE):HC7645 NONINVERTING HC7640 INVERTING ,HC7643 INVERTING/NONINVERTING
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明