M95128-WDW3T/P
更新时间:2024-09-18 13:07:38
描述:16KX8 SPI BUS SERIAL EEPROM, PDSO8, 0.169 INCH, HALOGEN FREE AND ROHS COMPLIANT, TSSOP-8
M95128-WDW3T/P 概述
16KX8 SPI BUS SERIAL EEPROM, PDSO8, 0.169 INCH, HALOGEN FREE AND ROHS COMPLIANT, TSSOP-8 EEPROM
M95128-WDW3T/P 规格参数
是否无铅: | 不含铅 | 是否Rohs认证: | 符合 |
生命周期: | Obsolete | 零件包装代码: | SOIC |
包装说明: | 0.169 INCH, HALOGEN FREE AND ROHS COMPLIANT, TSSOP-8 | 针数: | 8 |
Reach Compliance Code: | compliant | ECCN代码: | EAR99 |
HTS代码: | 8542.32.00.51 | 风险等级: | 5.16 |
最大时钟频率 (fCLK): | 5 MHz | 数据保留时间-最小值: | 40 |
耐久性: | 100000 Write/Erase Cycles | JESD-30 代码: | R-PDSO-G8 |
JESD-609代码: | e4 | 长度: | 4.4 mm |
内存密度: | 131072 bit | 内存集成电路类型: | EEPROM |
内存宽度: | 8 | 湿度敏感等级: | 1 |
功能数量: | 1 | 端子数量: | 8 |
字数: | 16384 words | 字数代码: | 16000 |
工作模式: | SYNCHRONOUS | 最高工作温度: | 125 °C |
最低工作温度: | -40 °C | 组织: | 16KX8 |
封装主体材料: | PLASTIC/EPOXY | 封装代码: | TSSOP |
封装等效代码: | TSSOP8,.25 | 封装形状: | RECTANGULAR |
封装形式: | SMALL OUTLINE, THIN PROFILE, SHRINK PITCH | 并行/串行: | SERIAL |
峰值回流温度(摄氏度): | 260 | 电源: | 3/5 V |
认证状态: | Not Qualified | 座面最大高度: | 1.2 mm |
串行总线类型: | SPI | 最大待机电流: | 0.000005 A |
子类别: | EEPROMs | 最大压摆率: | 0.006 mA |
最大供电电压 (Vsup): | 5.5 V | 最小供电电压 (Vsup): | 2.5 V |
标称供电电压 (Vsup): | 5 V | 表面贴装: | YES |
技术: | CMOS | 温度等级: | AUTOMOTIVE |
端子面层: | Nickel/Palladium/Gold (Ni/Pd/Au) | 端子形式: | GULL WING |
端子节距: | 0.65 mm | 端子位置: | DUAL |
处于峰值回流温度下的最长时间: | 30 | 宽度: | 3 mm |
最长写入周期时间 (tWC): | 5 ms | 写保护: | HARDWARE/SOFTWARE |
Base Number Matches: | 1 |
M95128-WDW3T/P 数据手册
通过下载M95128-WDW3T/P数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载M95256
M95128
256Kbit and 128Kbit Serial SPI Bus EEPROM
With High Speed Clock
FEATURES SUMMARY
■
Compatible with SPI Bus Serial Interface
Figure 1. Packages
(Positive Clock SPI Modes)
■
Single Supply Voltage:
–
–
–
4.5 to 5.5V for M95xxx
2.5 to 5.5V for M95xxx-W
1.8 to 5.5V for M95xxx-R
■
High Speed
8
–
10MHz Clock Rate, 5ms Write Time
■
■
■
■
■
■
■
■
Status Register
1
Hardware Protection of the Status Register
BYTE and PAGE WRITE (up to 64 Bytes)
Self-Timed Programming Cycle
Adjustable Size Read-Only EEPROM Area
Enhanced ESD Protection
PDIP8 (BN)
0.25 mm frame
More than 100000 Erase/Write Cycles
More than 40-Year Data Retention
8
1
SO8 (MN)
150 mil width
8
1
SO8 (MW)
200 mil width
Table 1. Product List
Reference
Part Number
M95256
M95256
M95128
M95256-W
M95256-R
M95128
TSSOP8 (DW)
169 mil width
M95128-W
M95128-R
October 2004
1/39
M95256, M95128
TABLE OF CONTENTS
FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 1. Product List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 1. Packages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 3. DIP, SO and TSSOP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 2. Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SIGNAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Serial Data Output (Q). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Serial Data Input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Write Protect (W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CONNECTING TO THE SPI BUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 4. Bus Master and Memory Devices on the SPI Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SPI Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 5. SPI Modes Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATING FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power On Reset: VCC Lock-Out Write Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Active Power and Standby Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hold Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 6. Hold Condition Activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
WIP bit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
WEL bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
BP1, BP0 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SRWD bit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 3. Status Register Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Data Protection and Protocol Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 4. Write-Protected Block Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MEMORY ORGANIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 7. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 5. Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 8. Write Enable (WREN) Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2/39
M95256, M95128
Write Disable (WRDI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 9. Write Disable (WRDI) Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Read Status Register (RDSR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WIP bit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WEL bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
BP1, BP0 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SRWD bit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 10.Read Status Register (RDSR) Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 6. Protection Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 11.Write Status Register (WRSR) Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Read from Memory Array (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 12.Read from Memory Array (READ) Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Write to Memory Array (WRITE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 13.Byte Write (WRITE) Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 14.Page Write (WRITE) Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
POWER-UP AND DELIVERY STATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power-up State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Initial Delivery State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 7. Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 8. Operating Conditions (M95xxx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 9. Operating Conditions (M95xxx-W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 10. Operating Conditions (M95xxx-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 11. AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 15.AC Measurement I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 12. Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 13. DC Characteristics (M95xxx, Device Grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 14. DC Characteristics (M95xxx, Device Grade 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 15. DC Characteristics (M95xxx-W, Device Grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 16. DC Characteristics (M95xxx-W, Device Grade 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 17. DC Characteristics (M95xxx-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 18. AC Characteristics (M95xxx, Device Grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 19. AC Characteristics (M95xxx, Device Grade 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 20. AC Characteristics (M95xxx-W, Device Grade 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 21. AC Characteristics (M95xxx-W, Device Grade 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 22. AC Characteristics (M95xxx-R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 16.Serial Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 17.Hold Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 18.Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3/39
M95256, M95128
Figure 19.PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Outline . . . . . . . . . . . . . . . . . 33
Table 23. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Mechanical Data . . . . . . . . . . 33
Figure 20.SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width, Package Outline . . . . 34
Table 24. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width, Package Mechanical Data
34
Figure 21.SO8 wide – 8 lead Plastic Small Outline, 200 mils body width, Package Outline . . . . . . 35
Table 25. SO8 wide – 8 lead Plastic Small Outline, 200 mils body width, Package Mechanical Data
35
Figure 22.TSSOP8 – 8 lead Thin Shrink Small Outline, Package Outline . . . . . . . . . . . . . . . . . . . 36
Table 26. TSSOP8 – 8 lead Thin Shrink Small Outline, Package Mechanical Data . . . . . . . . . . . . 36
PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 27. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 28. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4/39
M95256, M95128
Figure 3. DIP, SO and TSSOP Connections
SUMMARY DESCRIPTION
These electrically erasable programmable memo-
ry (EEPROM) devices are accessed by a high
speed SPI-compatible bus. The memory array is
organized as 32768 x 8 bit (M95256) and 16384 x
8 bit (M95128).
M95xxx
The device is accessed by a simple serial interface
that is SPI-compatible. The bus signals are C, D
and Q, as shown in Table 2. and Figure 2..
The device is selected when Chip Select (S) is tak-
en Low. Communications with the device can be
interrupted using Hold (HOLD).
S
Q
1
2
3
4
8
V
CC
HOLD
7
W
6
5
C
D
V
SS
AI01790D
Figure 2. Logic Diagram
Note: See PACKAGE MECHANICAL section for package dimen-
sions, and how to identify pin-1.
V
CC
Table 2. Signal Names
C
Serial Clock
Serial Data Input
Serial Data Output
Chip Select
Write Protect
Hold
D
C
S
Q
D
Q
M95xxx
S
W
W
HOLD
HOLD
V
Supply Voltage
Ground
CC
V
SS
V
SS
AI01789C
5/39
M95256, M95128
SIGNAL DESCRIPTION
During all operations, V must be held stable and
(Q) is at high impedance. Unless an internal Write
cycle is in progress, the device will be in the Stand-
by Power mode. Driving Chip Select (S) Low se-
lects the device, placing it in the Active Power
mode.
CC
within the specified valid range: V (min) to
CC
V
(max).
CC
All of the input and output signals must be held
High or Low (according to voltages of V , V , V
IH OH IL
or V , as specified in Table 13. to Table 17.).
These signals are described next.
After Power-up, a falling edge on Chip Select (S)
is required prior to the start of any instruction.
OL
Serial Data Output (Q). This output signal is
used to transfer data serially out of the device.
Data is shifted out on the falling edge of Serial
Clock (C).
Serial Data Input (D). This input signal is used to
transfer data serially into the device. It receives in-
structions, addresses, and the data to be written.
Values are latched on the rising edge of Serial
Clock (C).
Serial Clock (C). This input signal provides the
timing of the serial interface. Instructions, address-
es, or data present at Serial Data Input (D) are
latched on the rising edge of Serial Clock (C). Data
on Serial Data Output (Q) changes after the falling
edge of Serial Clock (C).
Hold (HOLD). The Hold (HOLD) signal is used to
pause any serial communications with the device
without deselecting the device.
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
To start the Hold condition, the device must be se-
lected, with Chip Select (S) driven Low.
Write Protect (W). The main purpose of this in-
put signal is to freeze the size of the area of mem-
ory that is protected against Write instructions (as
specified by the values in the BP1 and BP0 bits of
the Status Register).
This pin must be driven either High or Low, and
must be stable during all write instructions.
Chip Select (S). When this input signal is High,
the device is deselected and Serial Data Output
6/39
M95256, M95128
CONNECTING TO THE SPI BUS
These devices are fully compatible with the SPI
protocol.
All instructions, addresses and input data bytes
are shifted in to the device, most significant bit
first. The Serial Data Input (D) is sampled on the
first rising edge of the Serial Clock (C) after Chip
Select (S) goes Low.
All output data bytes are shifted out of the device,
most significant bit first. The Serial Data Output
(Q) is latched on the first falling edge of the Serial
Clock (C) after the instruction (such as the Read
from Memory Array and Read Status Register in-
structions) have been clocked into the device.
Figure 4. shows three devices, connected to an
MCU, on a SPI bus. Only one device is selected at
a time, so only one device drives the Serial Data
Output (Q) line at a time, all the others being high
impedance.
Figure 4. Bus Master and Memory Devices on the SPI Bus
SDO
SPI Interface with
(CPOL, CPHA) =
(0, 0) or (1, 1)
SDI
SCK
C
Q
D
C
Q
D
C Q D
Bus Master
(ST6, ST7, ST9,
ST10, Others)
SPI Memory
Device
SPI Memory
Device
SPI Memory
Device
CS3 CS2 CS1
S
S
S
W
HOLD
W
HOLD
HOLD
W
AI03746D
Note: The Write Protect (W) and Hold (HOLD) signals should be driven, High or Low as appropriate.
7/39
M95256, M95128
SPI Modes
These devices can be driven by a microcontroller
with its SPI peripheral running in either of the two
following modes:
is available from the falling edge of Serial Clock
(C).
The difference between the two modes, as shown
in Figure 5., is the clock polarity when the bus
master is in Stand-by mode and not transferring
data:
–
–
CPOL=0, CPHA=0
CPOL=1, CPHA=1
–
–
C remains at 0 for (CPOL=0, CPHA=0)
C remains at 1 for (CPOL=1, CPHA=1)
For these two modes, input data is latched in on
the rising edge of Serial Clock (C), and output data
Figure 5. SPI Modes Supported
CPOL CPHA
C
C
0
1
0
1
D
MSB
Q
MSB
AI01438B
8/39
M95256, M95128
OPERATING FEATURES
Power-up
When the power supply is turned on, V
consumes I , as specified in Table 13. to Table
17..
CC
rises
CC
from V to V
During this time, the Chip Select (S) must be al-
lowed to follow the V voltage. It must not be al-
lowed to float, but should be connected to V via
a suitable pull-up resistor.
.
When Chip Select (S) is High, the device is dese-
lected. If an Erase/Write cycle is not currently in
progress, the device then goes in to the Standby
Power mode, and the device consumption drops
SS
CC
CC
CC
to I
.
CC1
Hold Condition
As a built in safety feature, Chip Select (S) is edge
sensitive as well as level sensitive. After Power-
up, the device does not become selected until a
falling edge has first been detected on Chip Select
(S). This ensures that Chip Select (S) must have
been High, prior to going Low to start the first op-
eration.
The Hold (HOLD) signal is used to pause any se-
rial communications with the device without reset-
ting the clocking sequence.
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
Power On Reset: V
Lock-Out Write Protect
CC
To enter the Hold condition, the device must be
selected, with Chip Select (S) Low.
In order to prevent data corruption and inadvertent
Write instructions during Power-up, a Power On
Reset (POR) circuit is included. The internal reset
Normally, the device is kept selected, for the whole
duration of the Hold condition. Deselecting the de-
vice while it is in the Hold condition, has the effect
of resetting the state of the device, and this mech-
anism can be used if it is required to reset any pro-
cesses that had been in progress.
The Hold condition starts when the Hold (HOLD)
signal is driven Low at the same time as Serial
Clock (C) already being Low (as shown in Figure
6.).
is held active until V has reached the Power On
CC
Reset (POR) threshold voltage, and all operations
are disabled – the device will not respond to any
instruction. In the same way, when V drops from
the operating voltage, below the Power On Reset
(POR) threshold voltage, all operations are dis-
abled and the device will not respond to any in-
struction.
CC
A stable and valid V must be applied before ap-
CC
The Hold condition ends when the Hold (HOLD)
signal is driven High at the same time as Serial
Clock (C) already being Low.
plying any logic signal.
Power-down
At Power-down, the device must be deselected.
Chip Select (S) should be allowed to follow the
Figure 6. also shows what happens if the rising
and falling edges are not timed to coincide with
Serial Clock (C) being Low.
voltage applied on V
.
CC
Active Power and Standby Power Modes
When Chip Select (S) is Low, the device is select-
ed, and in the Active Power mode. The device
Figure 6. Hold Condition Activation
C
HOLD
Hold
Hold
Condition
Condition
AI02029D
9/39
M95256, M95128
Status Register
Figure 7. shows the position of the Status Register
in the control logic of the device. The Status Reg-
ister contains a number of status and control bits
that can be read or set (as appropriate) by specific
instructions.
device features the following data protection
mechanisms:
■
Write and Write Status Register instructions
are checked that they consist of a number of
clock pulses that is a multiple of eight, before
they are accepted for execution.
WIP bit. The Write In Progress (WIP) bit indicates
whether the memory is busy with a Write or Write
Status Register cycle.
WEL bit. The Write Enable Latch (WEL) bit indi-
cates the status of the internal Write Enable Latch.
■
All instructions that modify data must be
preceded by a Write Enable (WREN)
instruction to set the Write Enable Latch
(WEL) bit. This bit is returned to its reset state
by the following events:
–
–
Power-up
Write Disable (WRDI) instruction
completion
BP1, BP0 bits. The Block Protect (BP1, BP0) bits
are non-volatile. They define the size of the area to
be software protected against Write instructions.
SRWD bit. The Status Register Write Disable
(SRWD) bit is operated in conjunction with the
Write Protect (W) signal. The Status Register
Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware
Protected mode. In this mode, the non-volatile bits
of the Status Register (SRWD, BP1, BP0) become
read-only bits.
–
–
Write Status Register (WRSR) instruction
completion
Write (WRITE) instruction completion
■
■
The Block Protect (BP1, BP0) bits allow part of
the memory to be configured as read-only.
This is the Software Protected Mode (SPM).
The Write Protect (W) signal allows the Block
Protect (BP1, BP0) bits to be protected. This is
the Hardware Protected Mode (HPM).
Table 3. Status Register Format
For any instruction to be accepted, and executed,
Chip Select (S) must be driven High after the rising
edge of Serial Clock (C) for the last bit of the in-
struction, and before the next rising edge of Serial
Clock (C).
b7
b0
SRWD
0
0
0
BP1 BP0 WEL WIP
Two points need to be noted in the previous sen-
tence:
Status Register Write Protect
Block Protect Bits
Write Enable Latch Bit
Write In Progress Bit
–
The ‘last bit of the instruction’ can be the
eighth bit of the instruction code, or the eighth
bit of a data byte, depending on the instruction
(except for Read Status Register (RDSR) and
Read (READ) instructions).
Data Protection and Protocol Control
–
The ‘next rising edge of Serial Clock (C)’ might
(or might not) be the next bus transaction for
some other device on the SPI bus.
Non-volatile memory devices can be used in envi-
ronments that are particularly noisy, and within ap-
plications that could experience problems if
memory bytes are corrupted. Consequently, the
Table 4. Write-Protected Block Size
Status Register Bits
Array Addresses Protected
Protected Block
BP1
BP0
M95256
none
M95128
none
0
0
1
1
0
1
0
1
none
Upper quarter
Upper half
6000h - 7FFFh
4000h - 7FFFh
0000h - 7FFFh
3000h - 3FFFh
2000h - 3FFFh
0000h - 3FFFh
Whole memory
10/39
M95256, M95128
MEMORY ORGANIZATION
The memory is organized as shown in Figure 7..
Figure 7. Block Diagram
HOLD
High Voltage
Generator
W
S
Control Logic
C
D
Q
I/O Shift Register
Address Register
and Counter
Data
Register
Status
Register
Size of the
Read only
EEPROM
area
1 Page
X Decoder
AI01272C
11/39
M95256, M95128
INSTRUCTIONS
Each instruction starts with a single-byte code, as
summarized in Table 5..
If an invalid instruction is sent (one not contained
in Table 5.), the device automatically deselects it-
self.
Table 5. Instruction Set
Instruc
Instruction
Format
Description
tion
WREN Write Enable
0000 0110
0000 0100
0000 0101
0000 0001
0000 0011
0000 0010
WRDI
RDSR
Write Disable
Read Status Register
WRSR Write Status Register
READ Read from Memory Array
WRITE Write to Memory Array
12/39
M95256, M95128
Write Enable (WREN)
As shown in Figure 8., to send this instruction to
the device, Chip Select (S) is driven Low, and the
bits of the instruction byte are shifted in, on Serial
Data Input (D). The device then enters a wait
state. It waits for a the device to be deselected, by
Chip Select (S) being driven High.
The Write Enable Latch (WEL) bit must be set pri-
or to each WRITE and WRSR instruction. The only
way to do this is to send a Write Enable instruction
to the device.
Figure 8. Write Enable (WREN) Sequence
S
0
1
2
3
4
5
6
7
C
D
Q
Instruction
High Impedance
AI02281E
Write Disable (WRDI)
The device then enters a wait state. It waits for a
the device to be deselected, by Chip Select (S) be-
ing driven High.
The Write Enable Latch (WEL) bit, in fact, be-
comes reset by any of the following events:
One way of resetting the Write Enable Latch
(WEL) bit is to send a Write Disable instruction to
the device.
As shown in Figure 9., to send this instruction to
the device, Chip Select (S) is driven Low, and the
bits of the instruction byte are shifted in, on Serial
Data Input (D).
–
–
–
–
Power-up
WRDI instruction execution
WRSR instruction completion
WRITE instruction completion.
Figure 9. Write Disable (WRDI) Sequence
S
0
1
2
3
4
5
6
7
C
D
Q
Instruction
High Impedance
AI03750D
13/39
M95256, M95128
Read Status Register (RDSR)
BP1, BP0 bits. The Block Protect (BP1, BP0) bits
are non-volatile. They define the size of the area to
be software protected against Write instructions.
These bits are written with the Write Status Regis-
ter (WRSR) instruction. When one or both of the
Block Protect (BP1, BP0) bits is set to 1, the rele-
vant memory area (as defined in Table 3.) be-
comes protected against Write (WRITE)
instructions. The Block Protect (BP1, BP0) bits
can be written provided that the Hardware Protect-
ed mode has not been set.
The Read Status Register (RDSR) instruction al-
lows the Status Register to be read. The Status
Register may be read at any time, even while a
Write or Write Status Register cycle is in progress.
When one of these cycles is in progress, it is rec-
ommended to check the Write In Progress (WIP)
bit before sending a new instruction to the device.
It is also possible to read the Status Register con-
tinuously, as shown in Figure 10..
The status and control bits of the Status Register
are as follows:
WIP bit. The Write In Progress (WIP) bit indicates
whether the memory is busy with a Write or Write
Status Register cycle. When set to 1, such a cycle
is in progress, when reset to 0 no such cycle is in
progress.
SRWD bit. The Status Register Write Disable
(SRWD) bit is operated in conjunction with the
Write Protect (W) signal. The Status Register
Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware
Protected mode (when the Status Register Write
Disable (SRWD) bit is set to 1, and Write Protect
(W) is driven Low). In this mode, the non-volatile
bits of the Status Register (SRWD, BP1, BP0) be-
come read-only bits and the Write Status Register
(WRSR) instruction is no longer accepted for exe-
cution.
WEL bit. The Write Enable Latch (WEL) bit indi-
cates the status of the internal Write Enable Latch.
When set to 1 the internal Write Enable Latch is
set, when set to 0 the internal Write Enable Latch
is reset and no Write or Write Status Register in-
struction is accepted.
Figure 10. Read Status Register (RDSR) Sequence
S
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
C
D
Instruction
Status Register Out
Status Register Out
High Impedance
Q
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
MSB
MSB
AI02031E
14/39
M95256, M95128
Write Status Register (WRSR)
(WIP) bit. The Write In Progress (WIP) bit is 1 dur-
ing the self-timed Write Status Register cycle, and
is 0 when it is completed. When the cycle is com-
pleted, the Write Enable Latch (WEL) is reset.
The Write Status Register (WRSR) instruction al-
lows the user to change the values of the Block
Protect (BP1, BP0) bits, to define the size of the
area that is to be treated as read-only, as defined
in Table 3..
The Write Status Register (WRSR) instruction also
allows the user to set or reset the Status Register
Write Disable (SRWD) bit in accordance with the
Write Protect (W) signal. The Status Register
Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware
Protected Mode (HPM). The Write Status Register
(WRSR) instruction is not executed once the Hard-
ware Protected Mode (HPM) is entered.
The contents of the Status Register Write Disable
(SRWD) and Block Protect (BP1, BP0) bits are fro-
zen at their current values from just before the
start of the execution of Write Status Register
(WRSR) instruction. The new, updated, values
take effect at the moment of completion of the ex-
ecution of Write Status Register (WRSR) instruc-
tion.
The Write Status Register (WRSR) instruction al-
lows new values to be written to the Status Regis-
ter. Before it can be accepted, a Write Enable
(WREN) instruction must previously have been ex-
ecuted. After the Write Enable (WREN) instruction
has been decoded and executed, the device sets
the Write Enable Latch (WEL).
The Write Status Register (WRSR) instruction is
entered by driving Chip Select (S) Low, followed
by the instruction code and the data byte on Serial
Data Input (D).
The instruction sequence is shown in Figure 11..
The Write Status Register (WRSR) instruction has
no effect on b6, b5, b4, b1 and b0 of the Status
Register. b6, b5 and b4 are always read as 0.
Chip Select (S) must be driven High after the rising
edge of Serial Clock (C) that latches in the eighth
bit of the data byte, and before the next rising edge
of Serial Clock (C). Otherwise, the Write Status
Register (WRSR) instruction is not executed. As
soon as Chip Select (S) is driven High, the self-
timed Write Status Register cycle (whose duration
is t ) is initiated. While the Write Status Register
W
cycle is in progress, the Status Register may still
be read to check the value of the Write In Progress
Table 6. Protection Modes
Memory Content
W
Signal
SRWD
Bit
Write Protection of the
Status Register
Mode
1
1
Protected Area
Unprotected Area
1
0
0
0
Status Register is Writable
Software (if the WREN instruction
Protected has set the WEL bit)
Ready to accept Write
instructions
Write Protected
(SPM)
The values in the BP1 and
BP0 bits can be changed
1
1
Status Register is
Hardware Hardware write protected
Protected The values in the BP1 and Write Protected
Ready to accept Write
instructions
0
1
(HPM)
BP0 bits cannot be
changed
Note: 1. As defined by the values in the Block Protect (BP1, BP0) bits of the Status Register, as shown in Table 6..
The protection features of the device are summa-
rized in Table 4..
–
–
If Write Protect (W) is driven High, it is
possible to write to the Status Register
provided that the Write Enable Latch (WEL) bit
has previously been set by a Write Enable
(WREN) instruction.
If Write Protect (W) is driven Low, it is not
possible to write to the Status Register even if
the Write Enable Latch (WEL) bit has
When the Status Register Write Disable (SRWD)
bit of the Status Register is 0 (its initial delivery
state), it is possible to write to the Status Register
provided that the Write Enable Latch (WEL) bit has
previously been set by a Write Enable (WREN) in-
struction, regardless of the whether Write Protect
(W) is driven High or Low.
previously been set by a Write Enable
(WREN) instruction. (Attempts to write to the
Status Register are rejected, and are not
accepted for execution). As a consequence,
all the data bytes in the memory area that are
software protected (SPM) by the Block Protect
When the Status Register Write Disable (SRWD)
bit of the Status Register is set to 1, two cases
need to be considered, depending on the state of
Write Protect (W):
15/39
M95256, M95128
(BP1, BP0) bits of the Status Register, are
also hardware protected against data
modification.
The only way to exit the Hardware Protected Mode
(HPM) once entered is to pull Write Protect (W)
High.
Regardless of the order of the two events, the
Hardware Protected Mode (HPM) can be entered:
If Write Protect (W) is permanently tied High, the
Hardware Protected Mode (HPM) can never be
activated, and only the Software Protected Mode
(SPM), using the Block Protect (BP1, BP0) bits of
the Status Register, can be used.
–
by setting the Status Register Write Disable
(SRWD) bit after driving Write Protect (W) Low
–
or by driving Write Protect (W) Low after
setting the Status Register Write Disable
(SRWD) bit.
Figure 11. Write Status Register (WRSR) Sequence
S
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
C
Instruction
Status
Register In
7
6
5
4
3
2
0
1
D
Q
High Impedance
MSB
AI02282D
16/39
M95256, M95128
Read from Memory Array (READ)
When the highest address is reached, the address
counter rolls over to zero, allowing the Read cycle
to be continued indefinitely. The whole memory
can, therefore, be read with a single READ instruc-
tion.
The Read cycle is terminated by driving Chip Se-
lect (S) High. The rising edge of the Chip Select
(S) signal can occur at any time during the cycle.
As shown in Figure 12., to send this instruction to
the device, Chip Select (S) is first driven Low. The
bits of the instruction byte and address bytes are
then shifted in, on Serial Data Input (D). The ad-
dress is loaded into an internal address register,
and the byte of data at that address is shifted out,
on Serial Data Output (Q).
If Chip Select (S) continues to be driven Low, the
internal address register is automatically incre-
mented, and the byte of data at the new address is
shifted out.
The first byte addressed can be any byte within
any page.
The instruction is not accepted, and is not execut-
ed, if a Write cycle is currently in progress.
Figure 12. Read from Memory Array (READ) Sequence
S
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
C
Instruction
16-Bit Address
15 14 13
MSB
3
2
1
0
D
Q
Data Out 1
Data Out 2
High Impedance
2
7
6
5
4
3
1
7
0
MSB
AI01793D
Note: The most significant address bits (b15 for the M95256, and bits b15 and b14 for the M95128) are Don’t Care.
17/39
M95256, M95128
Write to Memory Array (WRITE)
Each time a new data byte is shifted in, the least
significant bits of the internal address counter are
incremented. If the number of data bytes sent to
the device exceeds the page boundary, the inter-
nal address counter rolls over to the beginning of
the page, and the previous data there are overwrit-
ten with the incoming data. (The page size of
these devices is 64 bytes).
As shown in Figure 13., to send this instruction to
the device, Chip Select (S) is first driven Low. The
bits of the instruction byte, address byte, and at
least one data byte are then shifted in, on Serial
Data Input (D).
The instruction is terminated by driving Chip Se-
lect (S) High at a byte boundary of the input data.
In the case of Figure 13., this occurs after the
eighth bit of the data byte has been latched in, in-
dicating that the instruction is being used to write
a single byte. The self-timed Write cycle starts,
The instruction is not accepted, and is not execut-
ed, under the following conditions:
–
if the Write Enable Latch (WEL) bit has not
been set to 1 (by executing a Write Enable
instruction just before)
and continues for a period t
(as specified in Ta-
WC
ble 18. to Table 22.), at the end of which the Write
in Progress (WIP) bit is reset to 0.
–
–
if a Write cycle is already in progress
if the device has not been deselected, by Chip
Select (S) being driven High, at a byte
boundary (after the eighth bit, b0, of the last
data byte that has been latched in)
if the addressed page is in the region
protected by the Block Protect (BP1 and BP0)
bits.
If, though, Chip Select (S) continues to be driven
Low, as shown in Figure 14., the next byte of input
data is shifted in, so that more than a single byte,
starting from the given address towards the end of
the same page, can be written in a single internal
Write cycle.
–
Figure 13. Byte Write (WRITE) Sequence
S
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
C
Instruction
16-Bit Address
Data Byte
15 14 13
3
2
1
0
7
6
5
4
3
2
0
1
D
Q
High Impedance
AI01795D
Note: The most significant address bits (b15 for the M95256, and bits b15 and b14 for the M95128) are Don’t Care.
18/39
M95256, M95128
Figure 14. Page Write (WRITE) Sequence
S
0
1
2
3
4
5
6
7
8
9
10
20 21 22 23 24 25 26 27 28 29 30 31
C
D
Instruction
16-Bit Address
Data Byte 1
15 14 13
3
2
1
0
7
6
5
4
3
2
0
1
S
C
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
Data Byte 2
Data Byte 3
Data Byte N
7
6
5
4
3
2
0
7
6
5
4
3
2
0
6
5
4
3
2
0
1
1
1
D
AI01796D
Note: The most significant address bits (b15 for the M95256, and bits b15 and b14 for the M95128) are Don’t Care.
19/39
M95256, M95128
POWER-UP AND DELIVERY STATE
Power-up State
Initial Delivery State
After Power-up, the device is in the following state:
The device is delivered with the memory array set
at all 1s (FFh). The Status Register Write Disable
(SRWD) and Block Protect (BP1 and BP0) bits are
initialized to 0.
–
–
Standby Power mode
deselected (after Power-up, a falling edge is
required on Chip Select (S) before any
instructions can be started).
–
–
–
not in the Hold Condition
the Write Enable Latch (WEL) is reset to 0
Write In Progress (WIP) is reset to 0
The SRWD, BP1 and BP0 bits of the Status Reg-
ister are unchanged from the previous power-
down (they are non-volatile bits).
20/39
M95256, M95128
MAXIMUM RATING
Stressing the device outside the ratings listed in
Table 7. may cause permanent damage to the de-
vice. These are stress ratings only, and operation
of the device at these, or any other conditions out-
side those indicated in the Operating sections of
this specification, is not implied. Exposure to Ab-
solute Maximum Rating conditions for extended
periods may affect device reliability. Refer also to
the STMicroelectronics SURE Program and other
relevant quality documents.
Table 7. Absolute Maximum Ratings
Symbol
Parameter
Min.
Max.
Unit
°C
°C
V
T
Storage Temperature
–65
150
STG
1
TLEAD
VO
Lead Temperature during Soldering
Output Voltage
See note
V
CC+0.6
6.5
–0.50
–0.50
–0.50
VI
Input Voltage
V
V
Supply Voltage
6.5
V
CC
2
VESD
–4000
4000
V
Electrostatic Discharge Voltage (Human Body model)
®
Note: 1. Compliant with JEDEC Std J-STD-020B (for small body, Sn-Pb or Pb assembly), the ST ECOPACK 7191395 specification, and
the European directive on Restrictions on Hazardous Substances (RoHS) 2002/95/EU
2. AEC-Q100-002 (compliant with JEDEC Std JESD22-A114A, C1=100pF, R1=1500Ω, R2=500Ω)
21/39
M95256, M95128
DC AND AC PARAMETERS
This section summarizes the operating and mea-
surement conditions, and the DC and AC charac-
teristics of the device. The parameters in the DC
and AC Characteristic tables that follow are de-
rived from tests performed under the Measure-
ment Conditions summarized in the relevant
tables. Designers should check that the operating
conditions in their circuit match the measurement
conditions when relying on the quoted parame-
ters.
Table 8. Operating Conditions (M95xxx)
Symbol
Parameter
Min.
4.5
Max.
5.5
Unit
V
V
CC
Supply Voltage
Ambient Operating Temperature (Device Grade 6)
Ambient Operating Temperature (Device Grade 3)
–40
–40
85
°C
°C
TA
125
Table 9. Operating Conditions (M95xxx-W)
Symbol
Parameter
Min.
2.5
Max.
5.5
Unit
V
V
CC
Supply Voltage
Ambient Operating Temperature (Device Grade 6)
Ambient Operating Temperature (Device Grade 3)
–40
–40
85
°C
°C
TA
1
125
Note: 1. This product is under development. For more information, please contact your nearest ST sales office.
Table 10. Operating Conditions (M95xxx-R)
1
1
Symbol
Unit
V
Parameter
Min.
1.8
Max.
5.5
V
CC
Supply Voltage
Ambient Operating Temperature
TA
–40
85
°C
Note: 1. This product is under development. For more information, please contact your nearest ST sales office.
22/39
M95256, M95128
Table 11. AC Measurement Conditions
Symbol
Parameter
Min.
Max.
Unit
pF
ns
V
C
Load Capacitance
100
L
Input Rise and Fall Times
50
CC
CC
0.2V to 0.8V
Input Pulse Voltages
CC
0.3V to 0.7V
Input and Output Timing Reference Voltages
V
CC
Note: Output Hi-Z is defined as the point where data out is no longer driven.
Figure 15. AC Measurement I/O Waveform
Input Levels
Input and Output
Timing Reference Levels
0.8V
CC
CC
0.7V
CC
0.3V
CC
0.2V
AI00825B
Table 12. Capacitance
Symbol
COUT
Parameter
Test Condition
= 0V
Min.
Max.
Unit
pF
Output Capacitance (Q)
Input Capacitance (D)
V
8
8
6
OUT
CIN
V
= 0V
= 0V
pF
IN
IN
Input Capacitance (other pins)
V
pF
Note: Sampled only, not 100% tested, at T =25°C and a frequency of 5 MHz.
A
23/39
M95256, M95128
Table 13. DC Characteristics (M95xxx, Device Grade 6)
Symbol
Parameter
Test Condition
VIN = VSS or VCC
Min.
Max.
± 2
Unit
µA
ILI
Input Leakage Current
Output Leakage Current
ILO
S = VCC, VOUT = VSS or VCC
± 2
µA
C = 0.1VCC/0.9VCC at 10MHz,
VCC = 5 V, Q = open
ICC
Supply Current
mA
µA
5
2
S = VCC , VCC = 5 V,
VIN = VSS or VCC
Supply Current
(Standby Power mode)
ICC1
VIL
VIH
0.3 VCC
VCC+1
Input Low Voltage
Input High Voltage
Output Low Voltage
–0.45
V
V
V
0.7 VCC
1
I
OL = 2 mA, VCC = 5 V
0.4
VOL
1
I
OH = –2 mA, VCC = 5 V
0.8 VCC
Output High Voltage
V
VOH
Note: 1. For all 5V range devices, the device meets the output requirements for both TTL and CMOS standards.
Table 14. DC Characteristics (M95xxx, Device Grade 3)
Symbol
Parameter
Test Condition
VIN = VSS or VCC
Min.
Max.
± 2
Unit
µA
ILI
Input Leakage Current
Output Leakage Current
ILO
S = VCC, VOUT = VSS or VCC
± 2
µA
C = 0.1VCC/0.9VCC at 5 MHz,
VCC = 5 V, Q = open
ICC
Supply Current
4
5
mA
µA
S = VCC , VCC = 5 V,
VIN = VSS or VCC
Supply Current
(Standby Power mode)
ICC1
VIL
VIH
0.3 VCC
VCC+1
0.4
Input Low Voltage
Input High Voltage
Output Low Voltage
–0.45
V
V
V
0.7 VCC
1
IOL = 2 mA, VCC = 5 V
IOH = –2 mA, VCC = 5 V
VOL
1
Output High Voltage
0.8 VCC
V
VOH
Note: 1. For all 5V range devices, the device meets the output requirements for both TTL and CMOS standards.
Table 15. DC Characteristics (M95xxx-W, Device Grade 6)
Symbol
Parameter
Test Condition
VIN = VSS or VCC
Min.
Max.
± 2
Unit
µA
ILI
Input Leakage Current
Output Leakage Current
ILO
S = VCC, VOUT = VSS or VCC
± 2
µA
C = 0.1VCC/0.9VCC at 5 MHz,
VCC = 2.5 V, Q = open
ICC
Supply Current
mA
µA
3
1
S = VCC , VCC = 2.5 V
VIN = VSS or VCC
Supply Current
(Standby Power mode)
ICC1
VIL
VIH
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
–0.45
0.3 VCC
VCC+1
0.4
V
V
V
V
0.7 VCC
VOL
VOH
I
OL = 1.5 mA, VCC = 2.5 V
I
OH = –0.4 mA, VCC = 2.5 V
0.8 VCC
24/39
M95256, M95128
Table 16. DC Characteristics (M95xxx-W, Device Grade 3)
Symbol
Parameter
Unit
µA
Test Condition
VIN = VSS or VCC
Min.
Max.
± 2
ILI
Input Leakage Current
Output Leakage Current
ILO
S = VCC, VOUT = VSS or VCC
± 2
µA
C = 0.1VCC/0.9VCC at 5 MHz,
VCC = 2.5 V, Q = open
ICC
Supply Current
mA
µA
3
2
Supply Current
(Standby Power mode)
ICC1
S = VCC , VCC = 2.5 V, VIN = VSS or VCC
VIL
VIH
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
–0.45
0.3 VCC
VCC+1
0.4
V
V
V
V
0.7 VCC
VOL
VOH
IOL = 1.5 mA, VCC = 2.5 V
IOH = –0.4 mA, VCC = 2.5 V
0.8 VCC
Table 17. DC Characteristics (M95xxx-R)
1
1
Symbol
Parameter
Unit
µA
Test Condition
VIN = VSS or VCC
Min.
Max.
ILI
Input Leakage Current
Output Leakage Current
± 2
± 2
ILO
S = VCC, VOUT = VSS or VCC
µA
C = 0.1VCC/0.9VCC at 2 MHz,
VCC = 1.8 V, Q = open
2
ICC
Supply Current
mA
µA
1
Supply Current
(Standby Power mode)
2
ICC1
S = VCC, VIN = VSS or VCC , VCC = 1.8 V
0.5
VIL
VIH
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
–0.45
0.25 VCC
VCC+1
0.3
V
V
V
V
0.7 VCC
VOL
VOH
I
OL = 0.15 mA, VCC = 1.8 V
I
OH = –0.1 mA, VCC = 1.8 V
0.8 VCC
Note: 1. This product is under development. For more infomation, please contact your nearest ST sales office.
2. This is preliminary data.
25/39
M95256, M95128
Table 18. AC Characteristics (M95xxx, Device Grade 6)
Test conditions specified in Table 11. and Table 8.
Symbol
Alt.
Parameter
Unit
MHz
ns
Min.
D.C.
15
Max.
f
C
f
Clock Frequency
10
SCK
CSS1
CSS2
t
t
t
S Active Setup Time
S Not Active Setup Time
S Deselect Time
SLCH
t
15
ns
SHCH
t
t
40
ns
SHSL
CS
t
t
CSH
S Active Hold Time
S Not Active Hold Time
Clock High Time
25
ns
CHSH
t
15
ns
CHSL
1
t
40
40
ns
t
CLH
CH
1
t
Clock Low Time
Clock Rise Time
ns
µs
t
CL
CLL
2
t
1
1
t
RC
CLCH
2
t
FC
Clock Fall Time
µs
ns
ns
ns
ns
ns
t
CHCL
t
t
DSU
Data In Setup Time
15
15
15
20
30
DVCH
t
t
Data In Hold Time
CHDX
DH
t
Clock Low Hold Time after HOLD not Active
Clock Low Hold Time after HOLD Active
Clock High Set-up Time before HOLD Active
HHCH
t
HLCH
t
CHHL
Clock High Set-up Time before HOLD not
Active
t
30
ns
CHHH
2
t
Output Disable Time
Clock Low to Output Valid
Output Hold Time
25
25
ns
ns
ns
t
DIS
SHQZ
t
t
CLQV
V
t
t
HO
0
CLQX
2
t
Output Rise Time
20
20
25
25
5
ns
ns
ns
ns
ms
t
RO
QLQH
2
t
Output Fall Time
t
FO
QHQL
t
t
LZ
HOLD High to Output Valid
HOLD Low to Output High-Z
Write Time
HHQV
2
t
t
HZ
HLQZ
t
W
t
WC
Note: 1. t + t must never be less than the shortest possible clock period, 1 / f (max)
CH
CL
C
2. Value guaranteed by characterization, not 100% tested in production.
26/39
M95256, M95128
Table 19. AC Characteristics (M95xxx, Device Grade 3)
Test conditions specified in Table 11. and Table 8.
Symbol
Alt.
Parameter
Unit
MHz
ns
Min.
D.C.
90
Max.
f
C
f
Clock Frequency
5
SCK
CSS1
CSS2
t
t
t
S Active Setup Time
S Not Active Setup Time
S Deselect Time
SLCH
t
90
ns
SHCH
t
t
100
90
ns
SHSL
CS
t
t
CSH
S Active Hold Time
S Not Active Hold Time
Clock High Time
ns
CHSH
t
90
ns
CHSL
1
t
90
90
ns
t
CLH
CH
1
t
Clock Low Time
Clock Rise Time
ns
µs
t
CL
CLL
2
t
1
1
t
RC
CLCH
2
t
FC
Clock Fall Time
µs
ns
ns
ns
ns
ns
t
CHCL
t
t
DSU
Data In Setup Time
20
30
70
40
60
DVCH
t
t
Data In Hold Time
CHDX
DH
t
Clock Low Hold Time after HOLD not Active
Clock Low Hold Time after HOLD Active
Clock High Set-up Time before HOLD Active
HHCH
t
HLCH
t
CHHL
Clock High Set-up Time before HOLD not
Active
t
60
ns
CHHH
2
t
Output Disable Time
Clock Low to Output Valid
Output Hold Time
100
60
ns
ns
ns
t
DIS
SHQZ
t
t
CLQV
V
t
t
HO
0
CLQX
2
t
Output Rise Time
50
50
50
100
5
ns
ns
ns
ns
ms
t
RO
QLQH
2
t
Output Fall Time
t
FO
QHQL
t
t
LZ
HOLD High to Output Valid
HOLD Low to Output High-Z
Write Time
HHQV
2
t
t
HZ
HLQZ
t
W
t
WC
Note: 1. t + t must never be less than the shortest possible clock period, 1 / f (max)
CH
CL
C
2. Value guaranteed by characterization, not 100% tested in production.
27/39
M95256, M95128
Table 20. AC Characteristics (M95xxx-W, Device Grade 6)
Test conditions specified in Table 11. and Table 9.
Symbol
Alt.
Parameter
Unit
MHz
ns
Min.
D.C.
90
Max.
f
C
f
Clock Frequency
5
SCK
CSS1
CSS2
t
t
t
S Active Setup Time
S Not Active Setup Time
S Deselect Time
SLCH
t
90
ns
SHCH
t
t
100
90
ns
SHSL
CS
t
t
CSH
S Active Hold Time
S Not Active Hold Time
Clock High Time
ns
CHSH
t
90
ns
CHSL
1
t
90
90
ns
t
CLH
CH
1
t
Clock Low Time
Clock Rise Time
ns
µs
t
CL
CLL
2
t
1
1
t
RC
CLCH
2
t
FC
Clock Fall Time
µs
ns
ns
ns
ns
ns
t
CHCL
t
t
DSU
Data In Setup Time
20
30
70
40
60
DVCH
t
t
Data In Hold Time
CHDX
DH
t
Clock Low Hold Time after HOLD not Active
Clock Low Hold Time after HOLD Active
Clock High Set-up Time before HOLD Active
HHCH
t
HLCH
t
CHHL
Clock High Set-up Time before HOLD not
Active
t
60
ns
CHHH
2
t
Output Disable Time
Clock Low to Output Valid
Output Hold Time
100
60
ns
ns
ns
t
DIS
SHQZ
t
t
CLQV
V
t
t
HO
0
CLQX
2
t
Output Rise Time
50
50
50
100
5
ns
ns
ns
ns
ms
t
RO
QLQH
2
t
Output Fall Time
t
FO
QHQL
t
t
LZ
HOLD High to Output Valid
HOLD Low to Output High-Z
Write Time
HHQV
2
t
t
HZ
HLQZ
t
W
t
WC
Note: 1. t + t must never be less than the shortest possible clock period, 1 / f (max)
CH
CL
C
2. Value guaranteed by characterization, not 100% tested in production.
28/39
M95256, M95128
Table 21. AC Characteristics (M95xxx-W, Device Grade 3)
Test conditions specified in Table 11. and Table 9.
Symbol
Alt.
Parameter
Unit
MHz
ns
Min.
D.C.
90
Max.
f
f
Clock Frequency
5
C
SCK
CSS1
CSS2
t
t
t
S Active Setup Time
S Not Active Setup Time
S Deselect Time
SLCH
t
90
ns
SHCH
t
t
100
90
ns
SHSL
CS
t
t
CSH
S Active Hold Time
S Not Active Hold Time
Clock High Time
ns
CHSH
t
90
ns
CHSL
1
t
90
90
ns
t
CLH
CH
1
t
Clock Low Time
Clock Rise Time
ns
µs
t
CL
CLL
2
t
1
1
t
RC
CLCH
2
t
FC
Clock Fall Time
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
CHCL
t
t
DSU
Data In Setup Time
20
30
70
40
DVCH
t
t
DH
Data In Hold Time
CHDX
t
Clock Low Hold Time after HOLD not Active
Clock Low Hold Time after HOLD Active
Clock High Set-up Time before HOLD Active
Clock High Set-up Time before HOLD not Active
Output Disable Time
HHCH
t
HLCH
t
t
CHHL
CH
t
t
CHHH
CH
2
t
100
60
t
DIS
SHQZ
t
t
V
Clock Low to Output Valid
Output Hold Time
CLQV
t
t
0
CLQX
HO
RO
2
t
Output Rise Time
50
50
50
100
5
t
t
QLQH
2
t
FO
Output Fall Time
ns
ns
ns
ms
QHQL
t
t
HOLD High to Output Valid
HOLD Low to Output High-Z
Write Time
HHQV
LZ
2
t
HZ
t
HLQZ
t
W
t
WC
Note: 1. t + t must never be less than the shortest possible clock period, 1 / f (max)
CH
CL
C
2. Value guaranteed by characterization, not 100% tested in production.
29/39
M95256, M95128
Table 22. AC Characteristics (M95xxx-R)
Test conditions specified in Table 11. and Table 10.
3,4
3,4
Symbol
Alt.
Parameter
Unit
MHz
ns
Min.
D.C.
Max.
f
f
Clock Frequency
2
C
SCK
CSS1
CSS2
t
t
t
S Active Setup Time
S Not Active Setup Time
S Deselect Time
200
200
200
200
200
200
SLCH
t
ns
SHCH
t
t
ns
SHSL
CS
t
t
CSH
S Active Hold Time
S Not Active Hold Time
Clock High Time
ns
CHSH
t
ns
CHSL
1
t
ns
t
CLH
CH
1
t
Clock Low Time
Clock Rise Time
200
ns
µs
t
CLL
CL
2
t
1
1
t
RC
CLCH
2
t
Clock Fall Time
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
FC
CHCL
t
t
DSU
Data In Setup Time
40
50
DVCH
t
t
DH
Data In Hold Time
CHDX
t
Clock Low Hold Time after HOLD not Active
Clock Low Hold Time after HOLD Active
Clock High Set-up Time before HOLD Active
Clock High Set-up Time before HOLD not Active
Output Disable Time
140
90
HHCH
t
HLCH
t
t
CHHL
CH
t
t
CHHH
CH
2
t
250
150
t
DIS
SHQZ
t
t
V
Clock Low to Output Valid
Output Hold Time
CLQV
t
t
0
CLQX
HO
RO
2
t
Output Rise Time
100
100
100
250
10
t
t
QLQH
2
t
Output Fall Time
ns
ns
ns
ms
FO
QHQL
t
t
HOLD High to Output Valid
HOLD Low to Output High-Z
Write Time
HHQV
LZ
2
t
t
HZ
HLQZ
t
W
t
WC
Note: 1. t + t must never be less than the shortest possible clock period, 1 / f (max)
CH
CL
C
2. Value guaranteed by characterization, not 100% tested in production.
3. This product is under development. For more infomation, please contact your nearest ST sales office.
4. This is preliminary data.
30/39
M95256, M95128
Figure 16. Serial Input Timing
tSHSL
S
tCHSL
tSLCH
tCHSH
tSHCH
C
tDVCH
tCHCL
tCHDX
tCLCH
MSB IN
LSB IN
D
Q
High Impedance
AI01447C
Figure 17. Hold Timing
S
tHLCH
tCHHL
tHHCH
C
tCHHH
tHLQZ
tHHQV
Q
D
HOLD
AI02032B
31/39
M95256, M95128
Figure 18. Output Timing
S
tCH
C
tCLQV
tCLQV
tCL
tSHQZ
tCLQX
tCLQX
LSB OUT
Q
D
tQLQH
tQHQL
ADDR.LSB IN
AI01449D
32/39
M95256, M95128
PACKAGE MECHANICAL
Figure 19. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Outline
E
b2
A2
A1
A
L
c
b
e
eA
eB
D
8
1
E1
PDIP-B
Note: Drawing is not to scale.
Table 23. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Mechanical Data
mm
inches
Min.
Symb.
Typ.
Min.
Max.
Typ.
Max.
A
A1
A2
b
5.33
0.210
0.38
2.92
0.36
1.14
0.20
9.02
7.62
6.10
–
0.015
0.115
0.014
0.045
0.008
0.355
0.300
0.240
–
3.30
0.46
1.52
0.25
9.27
7.87
6.35
2.54
7.62
4.95
0.56
1.78
0.36
10.16
8.26
7.11
–
0.130
0.018
0.060
0.010
0.365
0.310
0.250
0.100
0.300
0.195
0.022
0.070
0.014
0.400
0.325
0.280
–
b2
c
D
E
E1
e
eA
eB
L
–
–
–
–
10.92
3.81
0.430
0.150
3.30
2.92
0.130
0.115
33/39
M95256, M95128
Figure 20. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width, Package Outline
h x 45˚
A
C
B
CP
e
D
N
E
H
1
A1
α
L
SO-a
Note: Drawing is not to scale.
Table 24. SO8 narrow – 8 lead Plastic Small Outline, 150 mils body width, Package Mechanical Data
mm
Min.
1.35
0.10
0.33
0.19
4.80
3.80
–
inches
Min.
0.053
0.004
0.013
0.007
0.189
0.150
–
Symb.
Typ.
Max.
1.75
0.25
0.51
0.25
5.00
4.00
–
Typ.
Max.
0.069
0.010
0.020
0.010
0.197
0.157
–
A
A1
B
C
D
E
e
1.27
0.050
H
h
5.80
0.25
0.40
0°
6.20
0.50
0.90
8°
0.228
0.010
0.016
0°
0.244
0.020
0.035
8°
L
α
N
CP
8
8
0.10
0.004
34/39
M95256, M95128
Figure 21. SO8 wide – 8 lead Plastic Small Outline, 200 mils body width, Package Outline
A2
A
C
B
CP
e
D
N
1
E
H
A1
α
L
SO-b
Note: Drawing is not to scale.
Table 25. SO8 wide – 8 lead Plastic Small Outline, 200 mils body width, Package Mechanical Data
mm
inches
Min.
Symb.
Typ.
Min.
Max.
2.03
0.25
1.78
0.45
–
Typ.
Max.
0.080
0.010
0.070
0.018
–
A
A1
A2
B
0.10
0.004
0.35
–
0.014
–
C
0.20
1.27
0.008
0.050
D
5.15
5.20
–
5.35
5.40
–
0.203
0.205
–
0.211
0.213
–
E
e
H
7.70
0.50
0°
8.10
0.80
10°
0.303
0.020
0°
0.319
0.031
10°
L
α
N
8
8
CP
0.10
0.004
35/39
M95256, M95128
Figure 22. TSSOP8 – 8 lead Thin Shrink Small Outline, Package Outline
D
8
5
c
E1
E
1
4
α
A1
L
A
A2
L1
CP
b
e
TSSOP8AM
Note: Drawing is not to scale.
Table 26. TSSOP8 – 8 lead Thin Shrink Small Outline, Package Mechanical Data
mm
inches
Min.
Symbol
Typ.
Min.
Max.
1.200
0.150
1.050
0.300
0.200
0.100
3.100
–
Typ.
Max.
0.0472
0.0059
0.0413
0.0118
0.0079
0.0039
0.1220
–
A
A1
A2
b
0.050
0.800
0.190
0.090
0.0020
0.0315
0.0075
0.0035
1.000
0.0394
c
CP
D
3.000
0.650
6.400
4.400
0.600
1.000
2.900
–
0.1181
0.0256
0.2520
0.1732
0.0236
0.0394
0.1142
–
e
E
6.200
4.300
0.450
6.600
4.500
0.750
0.2441
0.1693
0.0177
0.2598
0.1772
0.0295
E1
L
L1
α
0°
8°
0°
8°
36/39
M95256, M95128
PART NUMBERING
Table 27. Ordering Information Scheme
Example:
M95256
–
W MN
6
T
P
Device Type
M95 = SPI serial access EEPROM
Device Function
256 = 256 Kbit (32768 x 8)
128 = 128 Kbit (16384 x 8)
Operating Voltage
blank = V = 4.5 to 5.5V
CC
W = V = 2.5 to 5.5V
CC
R = V = 1.8 to 5.5V
CC
Package
BN = PDIP8
MN = SO8 (150 mil width)
MW = SO8 (200 mil width)
DW = TSSOP8 (169 mil width)
Device Grade
6 = Industrial temperature range, –40 to 85 °C.
Device tested with standard test flow
1
3 = Device tested with High Reliability Certified Flow .
Automotive temperature range (–40 to 125 °C)
Option
blank = Standard Packing
T = Tape and Reel Packing
Plating Technology
blank = Standard SnPb plating
P = Lead-Free and RoHS compliant
G = Lead-Free, RoHS compliant, Sb O -free and TBBA-free
2
3
Note: 1. ST strongly recommends the use of the Automotive Grade devices for use in an automotive environment. The High Reliability Cer-
tified Flow (HRCF) is described in the quality note QNEE9801. Please ask your nearest ST sales office for a copy.
For a list of available options (speed, package,
etc.) or for further information on any aspect of this
device, please contact your nearest ST Sales Of-
fice.
37/39
M95256, M95128
REVISION HISTORY
Table 28. Document Revision History
Date
Rev.
Description of Revision
New -V voltage range added (including the tables for DC characteristics, AC characteristics,
and ordering information).
17-Nov-1999
2.1
New -V voltage range extended to M95256 (including AC characteristics, and ordering
information).
07-Feb-2000
2.2
22-Feb-2000
15-Mar-2000
2.3 tCLCH and tCHCL, for the M95xxx-V, changed from 1µs to 100ns
2.4 -V voltage range changed to 2.7-3.6V
Lead Soldering Temperature in the Absolute Maximum Ratings table amended
Illustrations and Package Mechanical data updated
29-Jan-2001
12-Jun-2001
2.5
Correction to header of Table 12B
2.6 TSSOP14 Illustrations and Package Mechanical data updated
Document promoted from Preliminary Data to Full Data Sheet
08-Feb-2002
09-Aug-2002
24-Feb-2003
2.7 Announcement made of planned upgrade to 10 MHz clock for the 5V, –40 to 85°C, range.
M95128 split off to its own datasheet. Data added for new and forthcoming products, including
availability of the SO8 narrow package.
2.8
2.9 Omission of SO8 narrow package mechanical data remedied
26-Jun-2003 2.10 -V voltage range removed
Table of contents, and Pb-free options added. -S voltage range extended to -R. V (min)
improved to –0.45V
IL
21-Nov-2003
17-Mar-2004
3.0
4.0
Absolute Maximum Ratings for V (min) and V (min) changed. Soldering temperature
IO
CC
information clarified for RoHS compliant devices. Device grade information clarified
M95128 datasheet merged back in. Product List summary table added. AEC-Q100-002
21-Oct-2004
5.0 compliance. Device Grade information clarified. tHHQX corrected to tHHQV. 10MHz product
becomes standard
38/39
M95256, M95128
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2004 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
39/39
M95128-WDW3T/P 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
M95128-WDW3T/PC | STMICROELECTRONICS | 16KX8 SPI BUS SERIAL EEPROM, PDSO8, 0.169 INCH, HALOGEN FREE AND ROHS COMPLIANT, TSSOP-8 | 获取价格 | |
M95128-WDW3TG | STMICROELECTRONICS | 256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock | 获取价格 | |
M95128-WDW3TG/A | STMICROELECTRONICS | 128 Kbit serial SPI bus EEPROM with high speed clock | 获取价格 | |
M95128-WDW3TG/K | STMICROELECTRONICS | SPI BUS SERIAL EEPROM | 获取价格 | |
M95128-WDW3TG/P | STMICROELECTRONICS | 128 Kbit serial SPI bus EEPROM with high speed clock | 获取价格 | |
M95128-WDW3TG/PC | STMICROELECTRONICS | 128 Kbit serial SPI bus EEPROM with high speed clock | 获取价格 | |
M95128-WDW3TG/V | STMICROELECTRONICS | 16KX8 SPI BUS SERIAL EEPROM, PDSO8, 0.169 INCH, ROHS COMPLIANT, TSSOP-8 | 获取价格 | |
M95128-WDW3TGP | STMICROELECTRONICS | 128 Kbit Serial SPI bus EEPROM with high speed clock | 获取价格 | |
M95128-WDW3TGV | STMICROELECTRONICS | 128 Kbit Serial SPI bus EEPROM with high speed clock | 获取价格 | |
M95128-WDW3TP | STMICROELECTRONICS | 256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock | 获取价格 |
M95128-WDW3T/P 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6