MM24512-WMJ6T [STMICROELECTRONICS]
512 Kbit Serial I睠 Bus EEPROM; 512 Kbit的串行I眷总线EEPROM型号: | MM24512-WMJ6T |
厂家: | ST |
描述: | 512 Kbit Serial I睠 Bus EEPROM |
文件: | 总24页 (文件大小:381K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
M24512
512 Kbit Serial I²C Bus EEPROM
FEATURES SUMMARY
■
Two-Wire I2C Serial Interface
Supports 400 kHz Protocol
Figure 1. Packages
■
Supply Voltage Ranges:
–
–
1.8V to 5.5V (M24512 − R)
2.5V to 5.5V (M24512 − W)
■
■
■
■
■
■
■
■
Write Control Input
BYTE and PAGE WRITE (up to 128 Bytes)
RANDOM and SEQUENTIAL READ Modes
Self-Timed Programming Cycle
Automatic Address Incrementing
Enhanced ESD/Latch-Up Protection
More than 100,000 Erase/Write Cycles
More than 40-Year Data Retention
8
1
PDIP8 (BN)
Table 1. M24512 devices
Reference
8
Part Number
M24512 − W
M24512 − R
M24512
1
SO8 (MW)
208 mil width
8
1
SO8 (MN)
150 mil width
TSSOP8 (DW)
February 2005
1/24
M24512
TABLE OF CONTENTS
FEATURES SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 1. M24512 devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 1. Packages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Table 2. Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power On Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 3. DIP, SO and TSSOP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SIGNAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Serial Clock (SCL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Serial Data (SDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chip Enable (E0, E1, E2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Write Control (WC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 4. Maximum RP Value versus Bus Parasitic Capacitance (C) for an I2C Bus . . . . . . . . . . . . 5
Figure 5. I2C Bus Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 3. Device Select Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 4. Most Significant Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 5. Least Significant Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DEVICE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Start Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Stop Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Acknowledge Bit (ACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Data Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Memory Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 6. Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 6. Write Mode Sequences with WC=1 (data write inhibited) . . . . . . . . . . . . . . . . . . . . . . . . . 8
Write Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Byte Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Page Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 7. Write Mode Sequences with WC=0 (data write enabled) . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 8. Write Cycle Polling Flowchart using ACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Minimizing System Delays by Polling On ACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 9. Read Mode Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Read Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Random Address Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Current Address Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Sequential Read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Acknowledge in Read Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INITIAL DELIVERY STATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 7. Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2/24
M24512
DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 8. Operating Conditions (M24512 – W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 9. Operating Conditions (M24512 – R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 10. AC Measurement Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 10.AC Measurement I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 11. Input Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 12. DC Characteristics (M24512 – W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 13. DC Characteristics(1) (M24512 – R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 14. AC Characteristics (M24512 – W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 15. AC Characteristics(1) (M24512 – R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 11.AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PACKAGE MECHANICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 12.PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Outline . . . . . . . . . . . . . . . . . 18
Table 16. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Mechanical Data . . . . . . . . . . 18
Figure 13.SO8W – 8 lead Plastic Small Outline, 208 mils body width, Package Outline . . . . . . . . 19
Table 17. SO8W – 8 lead Plastic Small Outline, 208 mils body width, Package Mechanical Data. 19
Figure 14.SO8N – 8 lead Plastic Small Outline, 150 mils body width, Package Outline. . . . . . . . . 20
Table 18. SO8N – 8 lead Plastic Small Outline, 150 mils body width, Package Mechanical Data . 20
Figure 15.TSSOP8 – 8 lead Thin Shrink Small Outline, Package Outline . . . . . . . . . . . . . . . . . . . 21
Table 19. TSSOP8 – 8 lead Thin Shrink Small Outline, Package Mechanical Data . . . . . . . . . . . . 21
PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 20. Ordering Information Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 21. Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3/24
M24512
ter. The Start condition is followed by a Device
Select Code and Read/Write bit (RW) (as de-
scribed in Table 3.), terminated by an acknowl-
edge bit.
SUMMARY DESCRIPTION
These I2C-compatible electrically erasable pro-
grammable memory (EEPROM) devices are orga-
nized as 64K x 8 bits.
When writing data to the memory, the device in-
serts an acknowledge bit during the 9th bit time,
following the bus master’s 8-bit transmission.
When data is read by the bus master, the bus
master acknowledges the receipt of the data byte
in the same way. Data transfers are terminated by
a Stop condition after an Ack for Write, and after a
NoAck for Read.
Figure 2. Logic Diagram
V
CC
3
Power On Reset
In order to prevent data corruption and inadvertent
Write operations during Power-up, a Power On
Reset (POR) circuit is included. At Power-up, the
device will not respond to any command until VCC
has reached the Power On Reset threshold volt-
age (this threshold is lower than the VCC min oper-
ating voltage defined in Tables 8 and 9). In the
same way, as soon as VCC drops from the normal
operating voltage, below the Power On Reset
threshold voltage, the device stops to respond to
any command.
E0-E2
SDA
M24512
SCL
WC
V
SS
AI02275
Prior to selecting and issuing commands to the
memory, a valid and stable VCC voltage must be
applied. This voltage must remain stable and valid
until the end of the transmission of the command
and, for a Write instruction, until the completion of
the internal write cycle (tW).
Table 2. Signal Names
E0, E1, E2
SDA
Chip Enable
Figure 3. DIP, SO and TSSOP Connections
Serial Data
Serial Clock
Write Control
Supply Voltage
Ground
SCL
WC
M24512
V
V
CC
SS
E0
E1
E2
1
2
3
4
8
V
CC
WC
7
6
5
SCL
SDA
I2C uses a two-wire serial interface, comprising a
bi-directional data line and a clock line. The devic-
es carry a built-in 4-bit Device Type Identifier code
(1010) in accordance with the I2C bus definition.
V
SS
AI04035B
The device behaves as a slave in the I2C protocol,
with all memory operations synchronized by the
serial clock. Read and Write operations are initiat-
ed by a Start condition, generated by the bus mas-
Note: See PACKAGE MECHANICAL section for package dimen-
sions, and how to identify pin-1.
4/24
M24512
SIGNAL DESCRIPTION
Serial Clock (SCL). This input signal is used to
strobe all data in and out of the device. In applica-
tions where this signal is used by slave devices to
synchronize the bus to a slower clock, the bus
master must have an open drain output, and a
pull-up resistor must be connected from Serial
Clock (SCL) to VCC. (Figure 4. indicates how the
value of the pull-up resistor can be calculated). In
most applications, though, this method of synchro-
nization is not employed, and so the pull-up resis-
tor is not necessary, provided that the bus master
has a push-pull (rather than open drain) output.
Serial Data (SDA). This bi-directional signal is
used to transfer data in or out of the device. It is an
open drain output that may be wire-OR’ed with
other open drain or open collector signals on the
bus. A pull up resistor must be connected from Se-
rial Data (SDA) to VCC. (Figure 4. indicates how
the value of the pull-up resistor can be calculated).
Chip Enable (E0, E1, E2). These input signals
are used to set the value that is to be looked for on
the three least significant bits (b3, b2, b1) of the 7-
bit Device Select Code. These inputs must be tied
to VCC or VSS, to establish the Device Select
Code. When not connected (left floating), these in-
puts are read as Low (0,0,0).
Write Control (WC). This input signal is useful
for protecting the entire contents of the memory
from inadvertent write operations. Write opera-
tions are disabled to the entire memory array when
Write Control (WC) is driven High. When uncon-
nected, the signal is internally read as VIL, and
Write operations are allowed.
When Write Control (WC) is driven High, Device
Select and Address bytes are acknowledged,
Data bytes are not acknowledged.
Figure 4. Maximum RP Value versus Bus Parasitic Capacitance (C) for an I2C Bus
V
CC
20
16
RP
RP
12
8
SDA
SCL
MASTER
C
fc = 100kHz
4
0
fc = 400kHz
C
10
100
C (pF)
1000
AI01665b
5/24
M24512
Figure 5. I2C Bus Protocol
SCL
SDA
SDA
Input
SDA
Change
START
Condition
STOP
Condition
1
2
3
7
8
9
SCL
SDA
ACK
MSB
START
Condition
1
2
3
7
8
9
SCL
SDA
MSB
ACK
STOP
Condition
AI00792B
Table 3. Device Select Code
1
2
RW
b0
Device Type Identifier
Chip Enable Address
b7
b6
0
b5
1
b4
0
b3
E2
b2
b1
Device Select Code
1
E1
E0
RW
Note: 1. The most significant bit, b7, is sent first.
2. E0, E1 and E2 are compared against the respective external pins on the memory device.
Table 4. Most Significant Byte
Table 5. Least Significant Byte
b15
b14
b13 b12 b11
b10 b9
b8
b7
b6
b5
b4
b3
b2
b1
b0
6/24
M24512
DEVICE OPERATION
The device supports the I2C protocol. This is sum-
marized in Figure 5.. Any device that sends data
on to the bus is defined to be a transmitter, and
any device that reads the data to be a receiver.
The device that controls the data transfer is known
as the bus master, and the other as the slave de-
vice. A data transfer can only be initiated by the
bus master, which will also provide the serial clock
for synchronization. The M24512 device is always
a slave in all communication.
Data (SDA) Low to acknowledge the receipt of the
eight data bits.
Data Input
During data input, the device samples Serial Data
(SDA) on the rising edge of Serial Clock (SCL).
For correct device operation, Serial Data (SDA)
must be stable during the rising edge of Serial
Clock (SCL), and the Serial Data (SDA) signal
must change only when Serial Clock (SCL) is driv-
en Low.
Start Condition
Memory Addressing
Start is identified by a falling edge of Serial Data
(SDA) while Serial Clock (SCL) is stable in the
High state. A Start condition must precede any
data transfer command. The device continuously
monitors (except during a Write cycle) Serial Data
(SDA) and Serial Clock (SCL) for a Start condition,
and will not respond unless one is given.
To start communication between the bus master
and the slave device, the bus master must initiate
a Start condition. Following this, the bus master
sends the Device Select Code, shown in Table 3.
(on Serial Data (SDA), most significant bit first).
The Device Select Code consists of a 4-bit Device
Type Identifier, and a 3-bit Chip Enable “Address”
(E2, E1, E0). To address the memory array, the 4-
bit Device Type Identifier is 1010b.
Up to eight memory devices can be connected on
a single I2C bus. Each one is given a unique 3-bit
code on the Chip Enable (E0, E1, E2) inputs.
When the Device Select Code is received, the de-
vice only responds if the Chip Enable Address is
the same as the value on the Chip Enable (E0, E1,
E2) inputs.
The 8th bit is the Read/Write bit (RW). This bit is
set to 1 for Read and 0 for Write operations.
If a match occurs on the Device Select code, the
corresponding device gives an acknowledgment
on Serial Data (SDA) during the 9th bit time. If the
device does not match the Device Select code, it
deselects itself from the bus, and goes into Stand-
by mode.
Stop Condition
Stop is identified by a rising edge of Serial Data
(SDA) while Serial Clock (SCL) is stable and driv-
en High. A Stop condition terminates communica-
tion between the device and the bus master. A
Read command that is followed by NoAck can be
followed by a Stop condition to force the device
into the Stand-by mode. A Stop condition at the
end of a Write command triggers the internal Write
cycle.
Acknowledge Bit (ACK)
The acknowledge bit is used to indicate a success-
ful byte transfer. The bus transmitter, whether it be
bus master or slave device, releases Serial Data
(SDA) after sending eight bits of data. During the
9th clock pulse period, the receiver pulls Serial
Table 6. Operating Modes
1
Mode
RW bit
Bytes
Initial Sequence
WC
X
Current Address Read
1
0
1
1
0
0
1
START, Device Select, RW = 1
X
START, Device Select, RW = 0, Address
reSTART, Device Select, RW = 1
Similar to Current or Random Address Read
START, Device Select, RW = 0
Random Address Read
1
X
Sequential Read
Byte Write
X
≥ 1
1
VIL
VIL
Page Write
≤ 128
START, Device Select, RW = 0
Note: 1. X = VIH or VIL.
7/24
M24512
Figure 6. Write Mode Sequences with WC=1 (data write inhibited)
WC
ACK
ACK
ACK
NO ACK
DATA IN
BYTE WRITE
DEV SEL
BYTE ADDR
BYTE ADDR
R/W
WC
ACK
ACK
ACK
NO ACK
DATA IN 1 DATA IN 2
PAGE WRITE
DEV SEL
BYTE ADDR
BYTE ADDR
R/W
WC (cont'd)
NO ACK
NO ACK
PAGE WRITE
(cont'd)
DATA IN N
AI01120C
Write Operations
When the bus master generates a Stop condition
immediately after the Ack bit (in the “10th bit” time
slot), either at the end of a Byte Write or a Page
Write, the internal Write cycle is triggered. A Stop
condition at any other time slot does not trigger the
internal Write cycle.
After the Stop condition, the delay tW, and the suc-
cessful completion of a Write operation, the de-
vice’s internal address counter is incremented
automatically, to point to the next byte address af-
ter the last one that was modified.
Following a Start condition the bus master sends
a Device Select Code with the Read/Write bit
(RW) reset to 0. The device acknowledges this, as
shown in Figure 7., and waits for two address
bytes. The device responds to each address byte
with an acknowledge bit, and then waits for the
data byte.
Writing to the memory may be inhibited if Write
Control (WC) is driven High. Any Write instruction
with Write Control (WC) driven High (during a pe-
riod of time from the Start condition until the end of
the two address bytes) will not modify the memory
contents, and the accompanying data bytes are
not acknowledged, as shown in Figure 6..
During the internal Write cycle, Serial Data (SDA)
is disabled internally, and the device does not re-
spond to any requests.
Byte Write
Each data byte in the memory has a 16-bit (two
byte wide) address. The Most Significant Byte (Ta-
ble 4.) is sent first, followed by the Least Signifi-
cant Byte (Table 5.). Bits b15 to b0 form the
address of the byte in memory.
After the Device Select code and the address
bytes, the bus master sends one data byte. If the
addressed location is Write-protected, by Write
Control (WC) being driven High, the device replies
with NoAck, and the location is not modified. If, in-
stead, the addressed location is not Write-protect-
8/24
M24512
ed, the device replies with Ack. The bus master
terminates the transfer by generating a Stop con-
dition, as shown in Figure 7.
data starts to become overwritten in an implemen-
tation dependent way.
The bus master sends from 1 to 128 bytes of data,
each of which is acknowledged by the device if
Write Control (WC) is Low. If Write Control (WC) is
High, the contents of the addressed memory loca-
tion are not modified, and each data byte is fol-
lowed by a NoAck. After each byte is transferred,
the internal byte address counter (the 7 least sig-
nificant address bits only) is incremented. The
transfer is terminated by the bus master generat-
ing a Stop condition.
Page Write
The Page Write mode allows up to 128 bytes to be
written in a single Write cycle, provided that they
are all located in the same ’row’ in the memory:
that is, the most significant memory address bits
(b15-b7) are the same. If more bytes are sent than
will fit up to the end of the row, a condition known
as ‘roll-over’ occurs. This should be avoided, as
Figure 7. Write Mode Sequences with WC=0 (data write enabled)
WC
ACK
ACK
ACK
ACK
BYTE WRITE
DEV SEL
BYTE ADDR
BYTE ADDR
DATA IN
R/W
WC
ACK
ACK
ACK
ACK
PAGE WRITE
DEV SEL
BYTE ADDR
BYTE ADDR
DATA IN 1
DATA IN 2
R/W
WC (cont'd)
ACK
ACK
PAGE WRITE
(cont'd)
DATA IN N
AI01106C
9/24
M24512
Figure 8. Write Cycle Polling Flowchart using ACK
WRITE Cycle
in Progress
START Condition
DEVICE SELECT
with RW = 0
ACK
Returned
NO
First byte of instruction
with RW = 0 already
decoded by the device
YES
Next
Operation is
Addressing the
Memory
NO
YES
Send Address
and Receive ACK
ReSTART
START
NO
YES
STOP
Condition
DATA for the
WRITE Operation
DEVICE SELECT
with RW = 1
Continue the
Continue the
Random READ Operation
WRITE Operation
AI01847C
Minimizing System Delays by Polling On ACK
–
–
Initial condition: a Write cycle is in progress.
During the internal Write cycle, the device discon-
nects itself from the bus, and writes a copy of the
data from its internal latches to the memory cells.
Step 1: the bus master issues a Start condition
followed by a Device Select Code (the first
byte of the new instruction).
The maximum Write time (t ) is shown in Table
w
–
Step 2: if the device is busy with the internal
Write cycle, no Ack will be returned and the
bus master goes back to Step 1. If the device
has terminated the internal Write cycle, it
responds with an Ack, indicating that the
device is ready to receive the second part of
the instruction (the first byte of this instruction
having been sent during Step 1).
14., but the typical time is shorter. To make use of
this, a polling sequence can be used by the bus
master.
The sequence, as shown in Figure 8., is:
10/24
M24512
Figure 9. Read Mode Sequences
ACK
NO ACK
DATA OUT
CURRENT
ADDRESS
READ
DEV SEL
R/W
ACK
ACK
ACK
ACK
NO ACK
DATA OUT
RANDOM
ADDRESS
READ
DEV SEL *
BYTE ADDR
BYTE ADDR
DEV SEL *
R/W
R/W
ACK
ACK
ACK
NO ACK
SEQUENTIAL
CURRENT
READ
DEV SEL
DATA OUT 1
DATA OUT N
R/W
ACK
ACK
ACK
ACK
ACK
SEQUENTIAL
RANDOM
READ
DEV SEL *
BYTE ADDR
BYTE ADDR
DEV SEL * DATA OUT 1
R/W
R/W
ACK
NO ACK
DATA OUT N
AI01105C
st
th
Note: 1. The seven most significant bits of the Device Select Code of a Random Read (in the 1 and 4 bytes) must be identical.
Read Operations
Read operations are performed independently of
the state of the Write Control (WC) signal.
After the successful completion of a Read opera-
tion, the device’s internal address counter is incre-
mented by one, to point to the next byte address.
this, and outputs the contents of the addressed
byte. The bus master must not acknowledge the
byte, and terminates the transfer with a Stop con-
dition.
Current Address Read
For the Current Address Read operation, following
a Start condition, the bus master only sends a De-
vice Select Code with the Read/Write bit (RW) set
to 1. The device acknowledges this, and outputs
the byte addressed by the internal address
counter. The counter is then incremented. The bus
master terminates the transfer with a Stop condi-
tion, as shown in Figure 9., without acknowledging
the byte.
Random Address Read
A dummy Write is first performed to load the ad-
dress into this address counter (as shown in Fig-
ure 9.) but without sending a Stop condition. Then,
the bus master sends another Start condition, and
repeats the Device Select Code, with the Read/
Write bit (RW) set to 1. The device acknowledges
11/24
M24512
Sequential Read
Acknowledge in Read Mode
This operation can be used after a Current Ad-
dress Read or a Random Address Read. The bus
master does acknowledge the data byte output,
and sends additional clock pulses so that the de-
vice continues to output the next byte in sequence.
To terminate the stream of bytes, the bus master
must not acknowledge the last byte, and must
generate a Stop condition, as shown in Figure 9.
For all Read commands, the device waits, after
each byte read, for an acknowledgment during the
9th bit time. If the bus master does not drive Serial
Data (SDA) Low during this time, the device termi-
nates the data transfer and switches to its Stand-
by mode.
The output data comes from consecutive address-
es, with the internal address counter automatically
incremented after each byte output. After the last
memory address, the address counter ‘rolls-over’,
and the device continues to output data from
memory address 00h.
INITIAL DELIVERY STATE
The device is delivered with all bits in the memory
array set to 1 (each byte contains FFh).
12/24
M24512
MAXIMUM RATING
Stressing the device outside the ratings listed in
Table 7. may cause permanent damage to the de-
vice. These are stress ratings only, and operation
of the device at these, or any other conditions out-
side those indicated in the Operating sections of
this specification, is not implied. Exposure to Ab-
solute Maximum Rating conditions for extended
periods may affect device reliability. Refer also to
the STMicroelectronics SURE Program and other
relevant quality documents.
Table 7. Absolute Maximum Ratings
Symbol
TA
Parameter
Ambient Operating Temperature
Min.
–40
–65
Max.
Unit
°C
°C
°C
V
125
TSTG
TLEAD
VIO
Storage Temperature
150
(1)
Lead Temperature during Soldering
Input or Output range
Supply Voltage
See note
–0.50
–0.50
–4000
6.5
6.5
VCC
V
2
VESD
4000
V
Electrostatic Discharge Voltage (Human Body model)
®
Note: 1. Compliant with JEDEC Std J-STD-020C (for small body, Sn-Pb or Pb assembly), the ST ECOPACK 7191395 specification, and
the European directive on Restrictions on Hazardous Substances (RoHS) 2002/95/EU
2. AEC-Q100-002 (compliant with JEDEC Std JESD22-A114A, C1=100pF, R1=1500Ω, R2=500Ω)
13/24
M24512
DC AND AC PARAMETERS
This section summarizes the operating and mea-
surement conditions, and the DC and AC charac-
teristics of the device. The parameters in the DC
and AC Characteristic tables that follow are de-
rived from tests performed under the Measure-
ment Conditions summarized in the relevant
tables. Designers should check that the operating
conditions in their circuit match the measurement
conditions when relying on the quoted parame-
ters.
Table 8. Operating Conditions (M24512 – W)
Symbol
Parameter
Min.
2.5
Max.
5.5
Unit
V
V
Supply Voltage
Ambient Operating Temperature
CC
TA
–40
85
°C
Table 9. Operating Conditions (M24512 – R)
Symbol
Parameter
Min.
1.8
Max.
5.5
Unit
V
V
Supply Voltage
Ambient Operating Temperature
CC
TA
–40
85
°C
Table 10. AC Measurement Conditions
Symbol
Parameter
Min.
Max.
Unit
pF
ns
V
C
Load Capacitance
100
L
Input Rise and Fall Times
Input Levels
50
0.2V to 0.8V
CC
CC
CC
0.3V to 0.7V
Input and Output Timing Reference Levels
V
CC
Figure 10. AC Measurement I/O Waveform
Input Levels
Input and Output
Timing Reference Levels
0.8V
CC
0.7V
CC
0.3V
CC
0.2V
CC
AI00825B
14/24
M24512
Table 11. Input Parameters
(1,2)
Symbol
CIN
Test Condition
Min.
Max.
Unit
pF
Parameter
Input Capacitance (SDA)
8
6
CIN
Input Capacitance (other pins)
pF
Input Impedance
(E2, E1, E0, WC)
(3)
VIN < 0.3V
30
kΩ
kΩ
ns
ZL
CC
Input Impedance
(E2, E1, E0, WC)
(3)
VIN > 0.7VCC
Single glitch
500
ZH
Pulse width ignored
(Input Filter on SCL and SDA)
tNS
100
Note: 1. T = 25 °C, f = 400 kHz
A
2. Sampled only, not 100% tested.
3. E2,E1,E0: Input impedance when the memory is selected (after a Start condition).
Table 12. DC Characteristics (M24512 – W)
Symbol
Parameter
Test Condition
IN = VSS or VCC
device in Standby mode
OUT = VSS or VCC, SDA in Hi-Z
CC = 2.5V, f =400kHz (rise/fall time < 30ns)
Min.
Max.
Unit
V
Input Leakage Current
(SCL, SDA, E0, E1, E2)
ILI
± 2
µA
(1)
ILO
Output Leakage Current
Supply Current
V
± 2
1
µA
mA
mA
µA
V
c
ICC
VCC = 5.5V, f =400kHz (rise/fall time < 30ns)
2
c
V
V
IN = VSS or VCC , VCC = 2.5 V
IN = VSS or VCC , VCC = 5.5 V
2
ICC1
Stand-by Supply Current
5
µA
Input Low Voltage
(SCL, SDA, WC)
VIL
–0.45
0.3VCC
V
Input High Voltage
(SCL, SDA, WC)
VIH
0.7VCC
VCC+1
0.4
V
V
VOL
Output Low Voltage
IOL = 2.1 mA, VCC = 2.5 V
Note: 1. When the device is selected (after a START condition), the Ei inputs have a different input impedance, as defined in Table 11.
Table 13. DC Characteristics(1) (M24512 – R)
Symbol
Parameter
Test Condition
VIN = VSS or VCC
Min.
Max.
± 2
± 2
1
Unit
µA
Input Leakage Current
(SCL, SDA, E2, E1, E0)
ILI
device in Stand-by mode
ILO
Output Leakage Current
Supply Current
V
OUT = VSS or VCC, SDA in Hi-Z
µA
VCC =1.8V, f = 400kHz (rise/fall time <
c
ICC
mA
30ns)
ICC1
VIL
Standby Supply Current
Input Low Voltage
V
IN = VSS or VCC , VCC = 1.8 V
2
µA
V
–0.45
0.3 VCC
VCC+1
0.2
VIH
VOL
Input High Voltage
Output Low Voltage
0.7VCC
V
IOL = 0.7 mA, VCC = 1.8 V
V
Note: 1. The information contained in Table 13. is related to the new M24512 (process letter “A”) and is subject to change without previous
notice.
15/24
M24512
Table 14. AC Characteristics (M24512 – W)
Symbol
fC
Alt.
fSCL
tHIGH
tLOW
tR
Parameter
Min.
Max.
Unit
kHz
ns
Clock Frequency
400
tCHCL
Clock Pulse Width High
Clock Pulse Width Low
Clock Rise Time
600
tCLCH
1300
ns
tCH1CH2
tCL1CL2
300
300
300
300
ns
tF
Clock Fall Time
ns
(2)
tR
SDA Rise Time
20
20
ns
tDH1DH2
tDL1DL2
tDXCX
(2)
tF
SDA Fall Time
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
tSU:DAT
tHD:DAT
tDH
Data In Set Up Time
100
0
tCLDX
Data In Hold Time
tCLQX
Data Out Hold Time
200
200
600
600
600
1300
(3)
tAA
Clock Low to Next Data Valid (Access Time)
Start Condition Set Up Time
Start Condition Hold Time
Stop Condition Set Up Time
Time between Stop Condition and Next Start Condition
Write Time
900
tCLQV
(1)
tSU:STA
tHD:STA
tSU:STO
tBUF
tCHDX
tDLCL
tCHDH
tDHDL
tW
(4)
tWR
5 or 10
Note: 1. For a reSTART condition, or following a Write cycle.
2. Sampled only, not 100% tested.
3. To avoid spurious START and STOP conditions, a minimum delay is placed between SCL=1 and the falling or rising edge of SDA.
4. For M24512 devices whose package marking shows the process letter “A” t (max) = 5ms whereas for M24512 devices whose
W
package marking shows the process letter “V” t (max) = 10ms
W
Table 15. AC Characteristics(1) (M24512 – R)
Symbol
fC
Alt.
fSCL
Parameter
Min.
Max.
Unit
kHz
ns
Clock Frequency
400
tCHCL
tCLCH
tHIGH
tLOW
tF
Clock Pulse Width High
Clock Pulse Width Low
SDA Fall Time
600
1300
20
ns
(3)
300
900
ns
tDL1DL2
tDXCX
tCLDX
tCLQX
tSU:DAT
tHD:DAT
tDH
Data In Set Up Time
Data In Hold Time
Data Out Hold Time
100
0
ns
ns
200
200
ns
(4)
tAA
Clock Low to Next Data Valid (Access Time)
Start Condition Set Up Time
ns
tCLQV
(2)
tSU:STA
tHD:STA
tSU:STO
tBUF
600
600
ns
ns
ns
ns
ms
tCHDX
tDLCL
tCHDH
tDHDL
tW
Start Condition Hold Time
Stop Condition Set Up Time
600
Time between Stop Condition and Next Start Condition
Write Time
1300
tWR
10
Note: 1. The information contained in Table 15. is related to the new M24512 (process letter “A”) and is subject to change without previous
notice.
2. For a reSTART condition, or following a Write cycle.
3. Sampled only, not 100% tested.
4. To avoid spurious START and STOP conditions, a minimum delay is placed between SCL=1 and the falling or rising edge of SDA.
16/24
M24512
Figure 11. AC Waveforms
tCHCL
tCLCH
SCL
tDLCL
SDA In
tCHDX
tCLDX
tDXCX
SDA
tCHDH tDHDL
Change
START
Condition
START
Condition
SDA
Input
STOP
Condition
SCL
SDA In
tCHDH
STOP
tCHDX
START
Condition
tW
Write Cycle
Condition
SCL
tCLQV
tCLQX
Data Valid
SDA Out
AI00795C
17/24
M24512
PACKAGE MECHANICAL
Figure 12. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Outline
E
b2
A2
A1
A
L
c
b
e
eA
eB
D
8
1
E1
PDIP-B
Note: Drawing is not to scale.
Table 16. PDIP8 – 8 pin Plastic DIP, 0.25mm lead frame, Package Mechanical Data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
A2
b
5.33
0.210
0.38
2.92
0.36
1.14
0.20
9.02
7.62
6.10
–
0.015
0.115
0.014
0.045
0.008
0.355
0.300
0.240
–
3.30
0.46
1.52
0.25
9.27
7.87
6.35
2.54
7.62
4.95
0.56
1.78
0.36
10.16
8.26
7.11
–
0.130
0.018
0.060
0.010
0.365
0.310
0.250
0.100
0.300
0.195
0.022
0.070
0.014
0.400
0.325
0.280
–
b2
c
D
E
E1
e
eA
eB
L
–
–
–
–
10.92
3.81
0.430
0.150
3.30
2.92
0.130
0.115
18/24
M24512
Figure 13. SO8W – 8 lead Plastic Small Outline, 208 mils body width, Package Outline
A2
A
C
B
CP
e
D
N
1
E
H
A1
α
L
SO-b
Note: Drawing is not to scale.
Table 17. SO8W – 8 lead Plastic Small Outline, 208 mils body width, Package Mechanical Data
millimeters
Min
inches
Min
Symbol
Typ
Max
2.03
0.25
1.78
0.45
–
Typ
Max
0.080
0.010
0.070
0.018
–
A
A1
A2
B
0.10
0.004
0.35
–
0.014
–
C
0.20
1.27
0.008
0.050
D
5.15
5.20
–
5.35
5.40
–
0.203
0.205
–
0.211
0.213
–
E
e
H
7.70
0.50
0°
8.10
0.80
10°
0.303
0.020
0°
0.319
0.031
10°
L
α
N
8
8
CP
0.10
0.004
19/24
M24512
Figure 14. SO8N – 8 lead Plastic Small Outline, 150 mils body width, Package Outline
h x 45˚
A2
A
C
B
ddd
e
D
8
1
E
H
A1
α
L
SO-A
Note: Drawing is not to scale.
Table 18. SO8N – 8 lead Plastic Small Outline, 150 mils body width, Package Mechanical Data
millimeters
Min
inches
Min
Symbol
Typ
Max
1.75
0.25
1.65
0.51
0.25
5.00
0.10
4.00
–
Typ
Max
0.069
0.010
0.065
0.020
0.010
0.197
0.004
0.157
–
A
A1
A2
B
1.35
0.053
0.004
0.043
0.013
0.007
0.189
0.10
1.10
0.33
C
0.19
D
4.80
ddd
E
3.80
–
0.150
–
e
1.27
0.050
H
5.80
0.25
0.40
0°
6.20
0.50
0.90
8°
0.228
0.010
0.016
0°
0.244
0.020
0.035
8°
h
L
α
N
8
8
20/24
M24512
Figure 15. TSSOP8 – 8 lead Thin Shrink Small Outline, Package Outline
D
8
5
c
E1
E
1
4
α
A1
L
A
A2
L1
CP
b
e
TSSOP8AM
Note: Drawing is not to scale.
Table 19. TSSOP8 – 8 lead Thin Shrink Small Outline, Package Mechanical Data
millimeters
Min
inches
Min
Symbol
Typ
Max
1.200
0.150
1.050
0.300
0.200
0.100
3.100
–
Typ
Max
A
A1
A2
b
0.0472
0.0059
0.0413
0.0118
0.0079
0.0039
0.1220
–
0.050
0.800
0.190
0.090
0.0020
0.0315
0.0075
0.0035
1.000
0.0394
c
CP
D
3.000
0.650
6.400
4.400
0.600
1.000
2.900
–
0.1181
0.0256
0.2520
0.1732
0.0236
0.0394
0.1142
–
e
E
6.200
4.300
0.450
6.600
4.500
0.750
0.2441
0.1693
0.0177
0.2598
0.1772
0.0295
E1
L
L1
α
0°
8
8°
0°
8
8°
N
21/24
M24512
PART NUMBERING
Table 20. Ordering Information Scheme
Example:
M24512
–
W MW
6
T
P
Device Type
2
M24 = I C serial access EEPROM
Device Function
512 = 512 Kbit (64K x 8)
Operating Voltage
W = V = 2.5 to 5.5V
CC
R = V = 1.8 to 5.5V
CC
Package
BN = PDIP8
MW = SO8 (208 mil width)
MN = SO8 (150 mil body width)
DW = TSSOP8
Device Grade
6 = Industrial temperature range, –40 to 85 °C.
Device tested with standard test flow
Option
blank = Standard Packing
T = Tape and Reel Packing
Plating Technology
blank = Standard SnPb plating
P or G = Lead-Free and RoHS compliant
For a list of available options (speed, package,
etc.) or for further information on any aspect of this
device, please contact your nearest ST Sales Of-
fice.
22/24
M24512
REVISION HISTORY
Table 21. Document Revision History
Date
Revision
Description of Revision
Lead Soldering Temperature in the Absolute Maximum Ratings table amended
Write Cycle Polling Flow Chart using ACK illustration updated
LGA8 and SO8(wide) packages added
29-Jan-2001
1.1
References to PSDIP8 changed to PDIP8, and Package Mechanical data updated
LGA8 Package Mechanical data and illustration updated
SO16 package removed
10-Apr-2001
1.2
16-Jul-2001
02-Oct-2001
1.3
1.4
LGA8 Package given the designator “LA”
LGA8 Package mechanical data updated
Document becomes Preliminary Data
13-Dec-2001
12-Jun-2001
22-Oct-2003
1.5
1.6
2.0
Test conditions for ILI, ILO, ZL and ZH made more precise
VIL and VIH values unified. tNS value changed
Document promoted to Full Datasheet
Table of contents, and Pb-free options added. Minor wording changes in Summary
Description, Power-On Reset, Memory Addressing, Write Operations, Read Operations.
V (min) improved to –0.45V.
IL
LGA8 package is Not for New Design. 5V and -S supply ranges, and Device Grade 5
removed. Absolute Maximum Ratings for V (min) and V (min) changed. Soldering
temperature information clarified for RoHS compliant devices. Device grade information
IO
CC
02-Sep-2004
3.0
clarified. AEC-Q100-002 compliance. V specification unified for SDA, SCL and WC
IL
INITIAL DELIVERY STATE is FFh (not necessarily the same as Erased).
LGA package removed, TSSOP8 and SO8N packages added (see PACKAGE
MECHANICAL section and Table 20., Ordering Information Scheme).
Voltage range R (1.8V to 5.5V) also offered. Minor wording changes.
Z Test Conditions modified in Table 11., Input Parameters and Note 3. added.
L
I
and I
values for V = 5.5V added to Table 12., DC Characteristics (M24512 – W).
CC1 CC
CC
22-Feb-2005
4.0
Note added to Table 12., DC Characteristics (M24512 – W).
Power On Reset paragraph specified.
t
max value modified in Table 14., AC Characteristics (M24512 – W) and note 4 added.
W
Plating technology changed in Table 20., Ordering Information Scheme.
Resistance and capacitance renamed in Figure 4., Maximum R Value versus Bus
P
2
Parasitic Capacitance (C) for an I C Bus.
23/24
M24512
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
ECOPACK is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2005 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
24/24
相关型号:
MM24FAN1.5000MHZ
HCMOS/TTL Output Clock Oscillator, 1.5MHz Nom, ROHS COMPLIANT, MINIATURE, CERAMIC, LEADLESS PACKAGE-4
MTRONPTI
MM24FAN50.0000MHZ
HCMOS/TTL Output Clock Oscillator, 50MHz Nom, ROHS COMPLIANT, MINIATURE, CERAMIC, LEADLESS PACKAGE-4
MTRONPTI
©2020 ICPDF网 联系我们和版权申明