NAND02GR4B2AN1 [STMICROELECTRONICS]
1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory; 1千兆, 2千兆, 2112字节/ 1056字页, 1.8V / 3V , NAND闪存型号: | NAND02GR4B2AN1 |
厂家: | ST |
描述: | 1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
文件: | 总64页 (文件大小:633K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NAND01G-B
NAND02G-B
1 Gbit, 2 Gbit,
2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory
Feature summary
●
High Density NAND Flash memories
–
–
–
Up to 2 Gbit memory array
Up to 64Mbit spare area
Cost effective solutions for mass
storage applications
●
NAND interface
–
–
–
x8 or x16 bus width
TSOP48 12 x 20mm
Multiplexed Address/ Data
Pinout compatibility for all densities
FBGA
●
●
●
●
Supply voltage
–
–
1.8V device: VDD = 1.7 to 1.95V
3.0V device: VDD = 2.7 to 3.6V
VFBGA63 9.5 x 12 x 1mm
TFBGA63 9.5 x 12 x 1.2mm
Page size
–
–
x8 device: (2048 + 64 spare) Bytes
x16 device: (1024 + 32 spare) Words
●
●
Serial Number option
Data protection
Block size
–
–
x8 device: (128K + 4K spare) Bytes
x16 device: (64K + 2K spare) Words
–
–
Hardware and Software Block Locking
Hardware Program/Erase locked during
Power transitions
Page Read/Program
–
–
–
Random access: 25µs (max)
Sequential access: 50ns (min)
Page program time: 300µs (typ)
●
Data integrity
–
–
100,000 Program/Erase cycles
10 years Data Retention
●
●
●
Copy Back Program mode
● ECOPACK® packages
–
Fast page copy without external
buffering
● Development tools
–
–
–
–
Error Correction Code software and
hardware models
Cache Program and Cache Read modes
–
Internal Cache Register to improve the
program and read throughputs
Bad Blocks Management and Wear
Leveling algorithms
Fast Block Erase
File System OS Native reference
software
–
Block erase time: 2ms (typ)
●
●
●
Status Register
Electronic Signature
Chip Enable ‘don’t care’
Hardware simulation models
–
for simple interface with microcontroller
February 2006
Rev 4.0
1/64
www.st.com
2
NAND01G-B, NAND02G-B
Part Number
Table 1.
Product List(1)
Reference
NAND01GR3B
NAND01GW3B
NAND01GR4B
NAND01GW4B
NAND02GR3B
NAND02GW3B
NAND02GR4B
NAND02GW4B
NAND01G-B
NAND02G-B
1. x16 organization only available for MCP Products.
2/64
NAND01G-B, NAND02G-B
Contents
Contents
1
2
Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Memory array organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1
Bad blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3
Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Inputs/Outputs (I/O0-I/O7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Inputs/Outputs (I/O8-I/O15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Address Latch Enable (AL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Command Latch Enable (CL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chip Enable (E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Read Enable (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power-Up Read Enable, Lock/Unlock Enable (PRL) . . . . . . . . . . . . . . . . 18
Write Enable (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Write Protect (WP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.10 Ready/Busy (RB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.11
3.12
V
V
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DD
SS
4
Bus operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1
4.2
4.3
4.4
4.5
4.6
Command Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Address Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Data Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Write Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5
6
Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Device operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1
Read Memory Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.1 Random Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3/64
Contents
NAND01G-B, NAND02G-B
6.1.2
Page Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.2
6.3
Cache Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Page Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.3.1
6.3.2
Sequential Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Random Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.4
6.5
6.6
6.7
6.8
Copy Back Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cache Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Block Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Read Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.8.1
6.8.2
6.8.3
6.8.4
6.8.5
6.8.6
Write Protection Bit (SR7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
P/E/R Controller and Cache Ready/Busy Bit (SR6) . . . . . . . . . . . . . . . 33
P/E/R Controller Bit (SR5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Cache Program Error Bit (SR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Error Bit (SR0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SR4, SR3 and SR2 are Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.9
Read Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7
8
Data protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.1
7.2
7.3
7.4
Blocks Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Blocks Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Blocks Lock-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Block Lock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Software algorithms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
8.1
8.2
8.3
8.4
8.5
8.6
Bad Block Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Block Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Garbage Collection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Wear-leveling algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Error Correction Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Hardware Simulation models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.6.1
8.6.2
Behavioral simulation models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IBIS simulations models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9
Program and Erase Times and Endurance cycles . . . . . . . . . . . . . . . . 44
4/64
NAND01G-B, NAND02G-B
Contents
10
11
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
DC And AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11.1 Ready/Busy Signal electrical characteristics . . . . . . . . . . . . . . . . . . . . . . 57
11.2 Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
12
13
14
Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5/64
List of tables
NAND01G-B, NAND02G-B
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Product List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Signal Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Valid Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Bus Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Address Insertion, x8 Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Address Insertion, x16 Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Address Definitions, x8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Address Definitions, x16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Copy Back Program x8 Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Copy Back Program x16 Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Status Register Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electronic Signature Byte/Word 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Block Lock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Block Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Program, Erase Times and Program Erase Endurance Cycles . . . . . . . . . . . . . . . . . . . . . 44
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Operating and AC Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
DC Characteristics, 1.8V Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
DC Characteristics, 3V Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
AC Characteristics for Command, Address, Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
AC Characteristics for Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
TSOP48 - 48 lead Plastic Thin Small Outline, 12 x 20 mm, Package Mechanical Data. . . 59
VFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Mechanical Data . . 60
TFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Mechanical Data . . 61
Ordering Information Scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
6/64
NAND01G-B, NAND02G-B
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Logic Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Logic Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TSOP48 Connections, x8 devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FBGA63 Connections, x8 devices (Top view through package). . . . . . . . . . . . . . . . . . . . . 13
FBGA63 Connections, x16 devices (Top view through package). . . . . . . . . . . . . . . . . . . . 14
Memory Array Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Read Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Random Data Output During Sequential Data Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cache Read Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 10. Page Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 11. Random Data Input During Sequential Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 12. Copy Back Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 13. Page Copy Back Program with Random Data Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 14. Cache Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 15. Block Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 16. Blocks Unlock Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 17. Read Block Lock Status Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 18. Block Protection State Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 19. Bad Block Management Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 20. Garbage Collection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 21. Error Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 22. Equivalent Testing Circuit for AC Characteristics Measurement . . . . . . . . . . . . . . . . . . . . 47
Figure 23. Command Latch AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 24. Address Latch AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 25. Data Input Latch AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 26. Sequential Data Output after Read AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Figure 27. Read Status Register AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 28. Read Electronic Signature AC Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 29. Page Read Operation AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 30. Page Program AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 31. Block Erase AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 32. Reset AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 33. Ready/Busy AC Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 34. Ready/Busy Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 35. Resistor Value Versus Waveform Timings For Ready/Busy Signal . . . . . . . . . . . . . . . . . . 58
Figure 36. Data Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 37. TSOP48 - 48 lead Plastic Thin Small Outline, 12 x 20 mm, Package Outline . . . . . . . . . . 59
Figure 38. VFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Outline. . . . . . . . . . 60
Figure 39. TFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Outline. . . . . . . . . . 61
7/64
Summary description
NAND01G-B, NAND02G-B
1
Summary description
The NAND Flash 2112 Byte/ 1056 Word Page is a family of non-volatile Flash memories
that uses NAND cell technology. The devices range from 1 Gbit to 2 Gbits and operate with
either a 1.8V or 3V voltage supply. The size of a Page is either 2112 Bytes (2048 + 64
spare) or 1056 Words (1024 + 32 spare) depending on whether the device has a x8 or x16
bus width.
The address lines are multiplexed with the Data Input/Output signals on a multiplexed x8 or
x16 Input/Output bus. This interface reduces the pin count and makes it possible to migrate
to other densities without changing the footprint.
Each block can be programmed and erased over 100,000 cycles. To extend the lifetime of
NAND Flash devices it is strongly recommended to implement an Error Correction Code
(ECC).
The devices have hardware and software security features:
●
A Write Protect pin is available to give a hardware protection against program and
erase operations.
●
A Block Locking scheme is available to provide user code and/or data protection.
The devices feature an open-drain Ready/Busy output that can be used to identify if the
Program/Erase/Read (P/E/R) Controller is currently active. The use of an open-drain output
allows the Ready/Busy pins from several memories to be connected to a single pull-up
resistor.
A Copy Back Program command is available to optimize the management of defective
blocks. When a Page Program operation fails, the data can be programmed in another page
without having to resend the data to be programmed.
Each device has Cache Program and Cache Read features which improve the program and
read throughputs for large files. During Cache Programming, the device loads the data in a
Cache Register while the previous data is transferred to the Page Buffer and programmed
into the memory array. During Cache Reading, the device loads the data in a Cache
Register while the previous data is transferred to the I/O Buffers to be read.
All devices have the Chip Enable Don’t Care feature, which allows code to be directly
downloaded by a microcontroller, as Chip Enable transitions during the latency time do not
stop the read operation.
All devices have the option of a Unique Identifier (serial number), which allows each device
to be uniquely identified.
The Unique Identifier options is subject to an NDA (Non Disclosure Agreement) and so not
described in the datasheet. For more details of this option contact your nearest ST Sales
office.
The devices are available in the following packages:
●
●
●
TSOP48 (12 x 20mm) for all products
VFBGA63 (9.5 x 12 x 1mm, 0.8mm pitch) for 1Gb products
TFBGA63 (9.5 x 12 x 1.2mm, 0.8mm pitch) for 2Gb Dual Die products
In order to meet environmental requirements, ST offers the NAND01G-B and NAND02G-B
in ECOPACK® packages. ECOPACK packages are Lead-free. The category of second Level
Interconnect is marked on the package and on the inner box label, in compliance with
8/64
NAND01G-B, NAND02G-B
Summary description
JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also
marked on the inner box label. ECOPACK is an ST trademark.
For information on how to order these options refer to Table 29: Ordering Information
Scheme. Devices are shipped from the factory with Block 0 always valid and the memory
content bits, in valid blocks, erased to ’1’.
See Table 2: Product Description, for all the devices available in the family.
Table 2.
Product Description(1)
Timings
Bus
Width
Page
Size
Block Memory Operating
Sequential
access
time
Random
access
time
Page
Program
time
Reference Part Number Density
Packages
Block
Erase
(typ)
Size
Array
Voltage
(max)
(typ)
(min)
1.7 to
1.95V
NAND01GR3B
NAND01GW3B
25µs
25µs
25µs
25µs
25µs
25µs
25µs
25µs
60ns
300µs
300µs
300µs
300µs
300µs
300µs
300µs
300µs
2048+ 128K+
x8
64
4K
2.7 to
3.6V
Bytes
Bytes
64
Pages x
1024
50ns
60ns
50ns
60ns
50ns
60ns
50ns
NAND01G
TSOP48
VFBGA63
1Gbit
2ms
-B
1.7 to
1.95V
NAND01GR4B
NAND01GW4B
NAND02GR3B
NAND02GW3B
Blocks
1024+
32
64K+
2K
x16(2)
2.7 to
3.6V
Words Words
1.7 to
1.95V
2048+ 128K+
x8
64
4K
2.7 to
3.6V
Bytes
Bytes
64
Pages x
2048
TSOP48
NAND02G
2Gbit
2ms TFBGA63
-B
(2)
1.7 to
1.95V
NAND02GR4B
NAND02GW4B
Blocks
1024+
32
64K+
2K
x16(2)
2.7 to
3.6V
Words Words
1. x16 organization only available for MCP
2. Dual Die devices only
9/64
Summary description
NAND01G-B, NAND02G-B
Figure 1.
Logic Block Diagram
Address
Register/Counter
AL
CL
W
NAND Flash
Memory Array
P/E/R Controller,
High Voltage
Generator
Command
Interface
Logic
E
WP
R
Page Buffer
Cache Register
Y Decoder
PRL
Command Register
I/O Buffers & Latches
RB
I/O0-I/O7, x8/x16
I/O8-I/O15, x16
AI09373b
Figure 2.
Logic Diagram
V
DD
I/O8-I/O15, x16
E
R
I/O0-I/O7, x8/x16
RB
W
NAND Flash
AL
CL
WP
PRL
V
SS
AI09372b
1. x16 organization only available for MCP
10/64
NAND01G-B, NAND02G-B
Summary description
Table 3.
Signal Names
I/O8-15
Data Input/Outputs for x16 devices
Data Input/Outputs, Address Inputs, or Command Inputs for x8 and
x16 devices
I/O0-7
AL
CL
E
Address Latch Enable
Command Latch Enable
Chip Enable
R
Read Enable
RB
W
Ready/Busy (open-drain output)
Write Enable
WP
PRL
VDD
VSS
NC
DU
Write Protect
Power-Up Read Enable, Lock/Unlock Enable
Supply Voltage
Ground
Not Connected Internally
Do Not Use
11/64
Summary description
NAND01G-B, NAND02G-B
Figure 3.
TSOP48 Connections, x8 devices
NC
NC
NC
NC
NC
NC
RB
R
1
48
NC
NC
NC
NC
I/O7
I/O6
I/O5
I/O4
NC
E
NC
NC
NC
PRL
NAND Flash
(x8)
V
DD
12
13
37
36
V
V
DD
V
SS
SS
NC
NC
CL
AL
NC
NC
NC
I/O3
I/O2
I/O1
I/O0
W
WP
NC
NC
NC
NC
NC
NC
NC
NC
NC
24
25
AI11750
12/64
NAND01G-B, NAND02G-B
Summary description
Figure 4.
FBGA63 Connections, x8 devices (Top view through package)
1
2
3
4
5
6
7
8
9
10
DU
DU
DU
A
B
DU
DU
DU
DU
AL
V
SS
C
WP
E
W
RB
D
E
F
NC
NC
NC
NC
R
CL
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
I/O3
NC
NC
NC
G
H
J
NC
NC
PRL
NC
NC
I/O0
I/O1
I/O2
NC
V
DD
V
I/O5
I/O6
I/O7
DD
V
K
L
I/O4
V
SS
SS
DU
DU
DU
DU
DU
DU
DU
DU
M
AI09376
13/64
Summary description
NAND01G-B, NAND02G-B
Figure 5.
FBGA63 Connections, x16 devices (Top view through package)
1
2
3
4
5
6
7
8
9
10
DU
DU
DU
A
B
DU
DU
DU
DU
V
SS
C
WP
AL
E
W
RB
D
E
F
NC
NC
R
CL
NC
NC
NC
NC
NC
NC
NC
NC
NC
I/O1
NC
NC
NC
NC
NC
NC
G
H
J
NC
NC
I/O5
I/O12
I/O7
I/O14
PRL
I/O8
I/O0
I/O10
V
DD
V
I/O9
I/O2
I/O3
I/O6
I/O15
DD
V
K
L
I/O11
I/O4
I/O13
V
SS
SS
DU
DU
DU
DU
DU
DU
DU
DU
M
AI09377
14/64
NAND01G-B, NAND02G-B
Memory array organization
2
Memory array organization
The memory array is made up of NAND structures where 32 cells are connected in series.
The memory array is organized in blocks where each block contains 64 pages. The array is
split into two areas, the main area and the spare area. The main area of the array is used to
store data whereas the spare area is typically used to store Error correction Codes, software
flags or Bad Block identification.
In x8 devices the pages are split into a 2048 Byte main area and a spare area of 64 Bytes.
In the x16 devices the pages are split into a 1,024 Word main area and a 32 Word spare
area. Refer to Figure 6: Memory Array Organization.
2.1
Bad blocks
The NAND Flash 2112 Byte/ 1056 Word Page devices may contain Bad Blocks, that is
blocks that contain one or more invalid bits whose reliability is not guaranteed. Additional
Bad Blocks may develop during the lifetime of the device.
The Bad Block Information is written prior to shipping (refer to Section 8.1: Bad Block
Management for more details).
Table 4: Valid Blocks shows the minimum number of valid blocks in each device. The values
shown include both the Bad Blocks that are present when the device is shipped and the Bad
Blocks that could develop later on.
These blocks need to be managed using Bad Blocks Management, Block Replacement or
Error Correction Codes (refer to Section 8: Software algorithms).
Table 4.
Valid Blocks
Density of Device
Min
Max
2 Gbits
1 Gbit
2008
1004
2048
1024
15/64
Memory array organization
NAND01G-B, NAND02G-B
Figure 6.
Memory Array Organization
x8 DEVICES
x16 DEVICES
Block = 64 Pages
Block = 64 Pages
Page = 2112 Bytes (2,048 + 64)
Page = 1056 Words (1024 + 32)
Main Area
Main Area
Block
Page
Block
Page
8 bits
16 bits
2048 Bytes
1024 Words
64
Bytes
32
Words
Page Buffer, 1056 Words
32
Page Buffer, 2112 Bytes
64
1,024 Words
Words
2,048 Bytes
16 bits
Bytes
8 bits
AI09854
16/64
NAND01G-B, NAND02G-B
Signal descriptions
3
Signal descriptions
See Figure 2: Logic Diagram, and Table 3: Signal Names, for a brief overview of the signals
connected to this device.
3.1
Inputs/Outputs (I/O0-I/O7)
Input/Outputs 0 to 7 are used to input the selected address, output the data during a Read
operation or input a command or data during a Write operation. The inputs are latched on
the rising edge of Write Enable. I/O0-I/O7 are left floating when the device is deselected or
the outputs are disabled.
3.2
Inputs/Outputs (I/O8-I/O15)
Input/Outputs 8 to 15 are only available in x16 devices. They are used to output the data
during a Read operation or input data during a Write operation. Command and Address
Inputs only require I/O0 to I/O7.
The inputs are latched on the rising edge of Write Enable. I/O8-I/O15 are left floating when
the device is deselected or the outputs are disabled.
3.3
3.4
3.5
Address Latch Enable (AL)
The Address Latch Enable activates the latching of the Address inputs in the Command
Interface. When AL is high, the inputs are latched on the rising edge of Write Enable.
Command Latch Enable (CL)
The Command Latch Enable activates the latching of the Command inputs in the Command
Interface. When CL is high, the inputs are latched on the rising edge of Write Enable.
Chip Enable (E)
The Chip Enable input activates the memory control logic, input buffers, decoders and
sense amplifiers. When Chip Enable is low, VIL, the device is selected. If Chip Enable goes
high, vIH, while the device is busy, the device remains selected and does not go into standby
mode.
3.6
Read Enable (R)
The Read Enable pin, R, controls the sequential data output during Read operations. Data
is valid tRLQV after the falling edge of R. The falling edge of R also increments the internal
column address counter by one.
17/64
Signal descriptions
NAND01G-B, NAND02G-B
3.7
Power-Up Read Enable, Lock/Unlock Enable (PRL)
The Power-Up Read Enable, Lock/Unlock Enable input, PRL, is used to enable and disable
the lock mechanism. When PRL is High, VIH, the device is in Block Lock mode.
If the Power-Up Read Enable, Lock/Unlock Enable input is not required, the PRL pin should
be left unconnected (Not Connected) or connected to VSS
.
3.8
Write Enable (W)
The Write Enable input, W, controls writing to the Command Interface, Input Address and
Data latches. Both addresses and data are latched on the rising edge of Write Enable.
During power-up and power-down a recovery time of 10µs (min) is required before the
Command Interface is ready to accept a command. It is recommended to keep Write Enable
high during the recovery time.
3.9
Write Protect (WP)
The Write Protect pin is an input that gives a hardware protection against unwanted program
or erase operations. When Write Protect is Low, VIL, the device does not accept any
program or erase operations.
It is recommended to keep the Write Protect pin Low, VIL, during power-up and power-down.
3.10
Ready/Busy (RB)
The Ready/Busy output, RB, is an open-drain output that can be used to identify if the P/E/R
Controller is currently active. When Ready/Busy is Low, VOL, a read, program or erase
operation is in progress. When the operation completes Ready/Busy goes High, VOH
.
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
Refer to the Section 11.1: Ready/Busy Signal electrical characteristics for details on how to
calculate the value of the pull-up resistor.
3.11
V
Supply Voltage
DD
VDD provides the power supply to the internal core of the memory device. It is the main
power supply for all operations (read, program and erase).
An internal voltage detector disables all functions whenever VDD is below VLKO (see
Table 22 and Table 23) or 1.5V (for 1.8V devices) to protect the device from any involuntary
program/erase during power-transitions.
Each device in a system should have VDD decoupled with a 0.1µF capacitor. The PCB track
widths should be sufficient to carry the required program and erase currents.
18/64
NAND01G-B, NAND02G-B
Bus operations
3.12
V
Ground
SS
Ground, VSS, is the reference for the power supply. It must be connected to the system
ground.
4
Bus operations
There are six standard bus operations that control the memory. Each of these is described
in this section, see Table 5: Bus Operations, for a summary.
Typically, glitches of less than 5 ns on Chip Enable, Write Enable and Read Enable are
ignored by the memory and do not affect bus operations.
4.1
4.2
Command Input
Command Input bus operations are used to give commands to the memory. Commands are
accepted when Chip Enable is Low, Command Latch Enable is High, Address Latch Enable
is Low and Read Enable is High. They are latched on the rising edge of the Write Enable
signal.
Only I/O0 to I/O7 are used to input commands.
See Figure 23 and Table 24 for details of the timings requirements.
Address Input
Address Input bus operations are used to input the memory addresses. Four bus cycles are
required to input the addresses for 1Gb devices whereas five bus cycles are required for the
2Gb device (refer to Table 6 and Table 7, Address Insertion).
The addresses are accepted when Chip Enable is Low, Address Latch Enable is High,
Command Latch Enable is Low and Read Enable is High. They are latched on the rising
edge of the Write Enable signal. Only I/O0 to I/O7 are used to input addresses.
See Figure 24 and Table 24 for details of the timings requirements.
4.3
Data Input
Data Input bus operations are used to input the data to be programmed.
Data is accepted only when Chip Enable is Low, Address Latch Enable is Low, Command
Latch Enable is Low and Read Enable is High. The data is latched on the rising edge of the
Write Enable signal. The data is input sequentially using the Write Enable signal.
See Figure 25 and Table 24 and Table 25 for details of the timings requirements.
19/64
Bus operations
NAND01G-B, NAND02G-B
4.4
Data Output
Data Output bus operations are used to read: the data in the memory array, the Status
Register, the lock status, the Electronic Signature and the Unique Identifier.
Data is output when Chip Enable is Low, Write Enable is High, Address Latch Enable is Low,
and Command Latch Enable is Low. The data is output sequentially using the Read Enable
signal.
See Figure 26 and Table 25 for details of the timings requirements.
4.5
4.6
Write Protect
Write Protect bus operations are used to protect the memory against program or erase
operations. When the Write Protect signal is Low the device will not accept program or erase
operations and so the contents of the memory array cannot be altered. The Write Protect
signal is not latched by Write Enable to ensure protection even during power-up.
Standby
When Chip Enable is High the memory enters Standby mode, the device is deselected,
outputs are disabled and power consumption is reduced.
Table 5.
Bus Operations
Bus Operation
E
AL
CL
R
W
WP
I/O0 - I/O7
I/O8 - I/O15(1)
Command Input
Address Input
Data Input
VIL
VIL
VIL
VIL
VIH
VIL
VIH
VIL
VIL
VIH Rising
VIH Rising
VIH Rising
X(2)
X
Command
Address
X
X
VIH
Data Input
Data Input
Fallin
VIH
g
Data Output
Write Protect
Standby
VIL
X
VIL
X
VIL
X
X
Data Output
Data Output
X
X
X
X
VIL
X
X
X
X
VIL/VD
VIH
X
X
D
1. Only for x16 devices.
2. WP must be VIH when issuing a program or erase command.
Table 6.
Address Insertion, x8 Devices
Bus Cycle(1)
I/O7
I/O6
I/O5
I/O4
I/O3
I/O2
I/O1
I/O0
1st
2nd
3rd
A7
VIL
A6
VIL
A5
VIL
A4
VIL
A3
A11
A15
A23
VIL
A2
A10
A14
A22
VIL
A1
A9
A0
A8
A19
A27
VIL
A18
A26
VIL
A17
A25
VIL
A16
A24
VIL
A13
A21
VIL
A12
A20
A28
4th
5th(2)
1. Any additional address input cycles will be ignored.
2. The fifth cycle is valid for 2Gb devices. A28 is for 2Gb devices only.
20/64
NAND01G-B, NAND02G-B
Bus operations
Table 7.
Address Insertion, x16 Devices
I/O8-
Bus
I/O7
I/O6
I/O5
I/O4
I/O3
I/O2
I/O1
I/O0
Cycle(1)
I/O15
1st
2nd
3rd
X
X
X
X
X
A7
VIL
A6
VIL
A5
VIL
A4
VIL
A3
VIL
A2
A10
A13
A21
VIL
A1
A9
A0
A8
A18
A26
VIL
A17
A25
VIL
A16
A24
VIL
A15
A23
VIL
A14
A22
VIL
A12
A20
VIL
A11
A19
A27
4th
5th(2)
1. Any additional address input cycles will be ignored.
2. The fifth cycle is valid for 2Gb devices. A27 is for 2Gb devices only.
Table 8.
Address Definitions, x8
Address
Definition
A0 - A11
A12 - A17
A18 - A27
A18 - A28
Column Address
Page Address
Block Address
Block Address
1Gb device
2Gb device
Table 9.
Address Definitions, x16
Address
Definition
A0 - A10
A11 - A16
A17 - A26
A17 - A27
Column Address
Page Address
Block Address
Block Address
1Gb device
2Gb device
21/64
Command Set
NAND01G-B, NAND02G-B
5
Command Set
All bus write operations to the device are interpreted by the Command Interface. The
Commands are input on I/O0-I/O7 and are latched on the rising edge of Write Enable when
the Command Latch Enable signal is high. Device operations are selected by writing
specific commands to the Command Register. The two-step command sequences for
program and erase operations are imposed to maximize data security.
The Commands are summarized in Table 10: Commands.
Table 10. Commands
Bus Write Operations(1)(2)
Commands
accepted
during
Command
1st CYCLE 2nd CYCLE 3rd CYCLE 4th CYCLE
busy
Read
00h(2)
05h
30h
E0h
31h
–
–
–
–
–
–
–
–
–
Random Data Output
Cache Read
00h
Exit Cache Read
34h
Yes(3)
Page Program
80h
10h
–
–
(Sequential Input default)
Random Data Input
Copy Back Program
Cache Program
Block Erase
85h
00h
80h
60h
FFh
90h
70h
7Ah
23h
2Ah
2Ch
–
35h
15h
D0h
–
–
85h
–
–
10h
–
–
–
Reset
–
–
Yes
Yes
Read Electronic Signature
Read Status Register
Read Block Lock Status
Blocks Unlock
–
–
–
–
–
–
–
–
–
24h
–
–
–
Blocks Lock
–
–
Blocks Lock-Down
–
–
–
1. The bus cycles are only shown for issuing the codes. The cycles required to input the
addresses or input/output data are not shown.
2. For consecutive Read operations the 00h command does not need to be repeated.
3. Only during Cache Read busy.
22/64
NAND01G-B, NAND02G-B
Device operations
6
Device operations
The following section gives the details of the device operations.
6.1
Read Memory Array
At Power-Up the device defaults to Read mode. To enter Read mode from another mode the
Read command must be issued, see Table 10: Commands. Once a Read command is
issued, subsequent consecutive Read commands only require the confirm command code
(30h).
Once a Read command is issued two types of operations are available: Random Read and
Page Read.
6.1.1
6.1.2
Random Read
Each time the Read command is issued the first read is Random Read.
Page Read
After the first Random Read access, the page data (2112 Bytes or 1056 Words) is
transferred to the Page Buffer in a time of tWHBH (refer to Table 25 for value). Once the
transfer is complete the Ready/Busy signal goes High. The data can then be read out
sequentially (from selected column address to last column address) by pulsing the Read
Enable signal.
The device can output random data in a page, instead of the consecutive sequential data, by
issuing a Random Data Output command.
The Random Data Output command can be used to skip some data during a sequential
data output.
The sequential operation can be resumed by changing the column address of the next data
to be output, to the address which follows the Random Data Output command.
The Random Data Output command can be issued as many times as required within a
page.
The Random Data Output command is not accepted during Cache Read operations.
23/64
Device operations
NAND01G-B, NAND02G-B
Figure 7.
Read Operations
CL
E
W
AL
R
tBLBH1
30h
RB
I/O
Address Input
00h
Data Output (sequentially)
Command
Code
Command
Code
Busy
ai08657b
1. Highest address depends on device density.
24/64
NAND01G-B, NAND02G-B
Device operations
Figure 8.
Random Data Output During Sequential Data Output
tBLBH1
(Read Busy time)
RB
Busy
R
Address
Address
Inputs
30h
E0h
I/O
00h
05h
Data Output
Data Output
Inputs
Cmd
Cmd
Cmd
Cmd
Code
Code
Code
Code
5 Add cycles
2Add cycles
Row Add 1,2,3 Col Add 1,2
Col Add 1,2
Spare
Area
Spare
Area
Main Area
Main Area
ai08658
25/64
Device operations
NAND01G-B, NAND02G-B
6.2
Cache Read
The Cache Read operation is used to improve the read throughput by reading data using
the Cache Register. As soon as the user starts to read one page, the device automatically
loads the next page into the Cache Register.
An Cache Read operation consists of three steps (see Table 10: Commands):
1. One bus cycle is required to setup the Cache Read command (the same as the
standard Read command)
2. Four or Five (refer to Table 6 and Table 7) bus cycles are then required to input the
Start Address
3. One bus cycle is required to issue the Cache Read confirm command to start the P/E/R
Controller.
The Start Address must be at the beginning of a page (Column Address = 00h, see Table 8
and Table 9). This allows the data to be output uninterrupted after the latency time (tBLBH1),
see Figure 9
The Ready/Busy signal can be used to monitor the start of the operation. During the latency
period the Ready/Busy signal goes Low, after this the Ready/Busy signal goes High, even if
the device is internally downloading page n+1.
Once the Cache Read operation has started, the Status Register can be read using the
Read Status Register command.
During the operation, SR5 can be read, to find out whether the internal reading is ongoing
(SR5 = ‘0’), or has completed (SR5 = ‘1’), while SR6 indicates whether the Cache Register
is ready to download new data.
To exit the Cache Read operation an Exit Cache Read command must be issued (see
Table 10).
If the Exit Cache Read command is issued while the device is internally reading page n+1,
page n will still be output, but not page n+1.
Figure 9.
Cache Read Operation
tBLBH1
(Read Busy time)
RB
Busy
Address
Inputs
last page
34h
I/O
31h
00h
1st page
2nd page 3rd page
Block N
Exit
Cache
Read
Code
Read
Setup
Code
Cache
Read
Confirm
Code
Data Output
ai08661
26/64
NAND01G-B, NAND02G-B
Device operations
6.3
Page Program
The Page Program operation is the standard operation to program data to the memory
array. Generally, data is programmed sequentially, however the device does support
Random Input within a page.
The memory array is programmed by page, however partial page programming is allowed
where any number of Bytes (1 to 2112) or Words (1 to 1056) can be programmed.
The maximum number of consecutive partial page program operations allowed in the same
page is eight. After exceeding this a Block Erase command must be issued before any
further program operations can take place in that page.
6.3.1
Sequential Input
To input data sequentially the addresses must be sequential and remain in one block.
For Sequential Input each Page Program operation consists of five steps (see Figure 10):
1. one bus cycle is required to setup the Page Program (Sequential Input) command (see
Table 10)
2. four or five bus cycles are then required to input the program address (refer to Table 6
and Table 7)
3. the data is then loaded into the Data Registers
4. one bus cycle is required to issue the Page Program confirm command to start the
P/E/R Controller. The P/E/R will only start if the data has been loaded in step 3.
5. the P/E/R Controller then programs the data into the array.
6.3.2
Random Data Input
During a Sequential Input operation, the next sequential address to be programmed can be
replaced by a random address, by issuing a Random Data Input command. The following
two steps are required to issue the command:
1. one bus cycle is required to setup the Random Data Input command (see Table 10)
2. two bus cycles are then required to input the new column address (refer to Table 6)
Random Data Input can be repeated as often as required in any given page.
Once the program operation has started the Status Register can be read using the Read
Status Register command. During program operations the Status Register will only flag
errors for bits set to '1' that have not been successfully programmed to '0'.
During the program operation, only the Read Status Register and Reset commands will be
accepted, all other commands will be ignored.
Once the program operation has completed the P/E/R Controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High.
The device remains in Read Status Register mode until another valid command is written to
the Command Interface.
27/64
Device operations
NAND01G-B, NAND02G-B
Figure 10. Page Program Operation
tBLBH2
(Program Busy time)
RB
I/O
Busy
Data Input
10h
Address Inputs
80h
70h
SR0
Confirm
Code
Read Status Register
Page Program
Setup Code
ai08659
Figure 11. Random Data Input During Sequential Data Input
tBLBH2
(Program Busy time)
RB
I/O
Busy
Address
Inputs
Address
Inputs
80h
85h
10h
Data Intput
Data Input
70h
SR0
Cmd
Code
Cmd
Confirm
Code
Read Status Register
Code 2 Add cycles
5 Add cycles
Col Add 1,2
Row Add 1,2,3 Col Add 1,2
Spare
Area
Spare
Area
Main Area
Main Area
ai08664
28/64
NAND01G-B, NAND02G-B
Device operations
6.4
Copy Back Program
The Copy Back Program operation is used to copy the data stored in one page and
reprogram it in another page.
The Copy Back Program operation does not require external memory and so the operation
is faster and more efficient because the reading and loading cycles are not required. The
operation is particularly useful when a portion of a block is updated and the rest of the block
needs to be copied to the newly assigned block.
If the Copy Back Program operation fails an error is signalled in the Status Register.
However as the standard external ECC cannot be used with the Copy Back Program
operation bit error due to charge loss cannot be detected. For this reason it is recommended
to limit the number of Copy Back Program operations on the same data and or to improve
the performance of the ECC.
The Copy Back Program operation requires four steps:
1. The first step reads the source page. The operation copies all 1056 Words/ 2112 Bytes
from the page into the Data Buffer. It requires:
–
–
–
one bus write cycle to setup the command
4 bus write cycles to input the source page address
one bus write cycle to issue the confirm command code
2. When the device returns to the ready state (Ready/Busy High), the next bus write cycle
of the command is given with the 4 bus cycles to input the target page address. Refer
to Table 11 for the addresses that must be the same for the Source and Target pages.
3. Then the confirm command is issued to start the P/E/R Controller.
To see the Data Input cycle for modifying the source page and an example of the Copy Back
Program operation refer to Figure 12.
A data input cycle to modify a portion or a multiple distant portion of the source page, is
shown in Figure 13
Table 11. Copy Back Program x8 Addresses
Density
Same Address for Source and Target Pages
1 Gbit
no constraint
no constraint
A28
2 Gbit
2 Gbit DD(1)
1. DD = Dual Die
Table 12. Copy Back Program x16 Addresses
Density Same Address for Source and Target Pages
1 Gbit
no constraint
no constraint
A27
2 Gbit
2 Gbit DD(1)
1. DD = Dual Die
29/64
Device operations
NAND01G-B, NAND02G-B
Figure 12. Copy Back Program
Source
Target
Add Inputs
I/O
10h
70h
SR0
35h
85h
00h
Add Inputs
Read
Code
Copy Back
Code
Read Status Register
tBLBH1
tBLBH2
(Read Busy time)
(Program Busy time)
RB
Busy
Busy
ai09858b
1. Copy back program is only permitted between odd address pages or even address pages.
Figure 13. Page Copy Back Program with Random Data Input
2 Cycle
Add Inputs
Target
Add Inputs
Source
Add Inputs
I/O
35h
SR0
00h
85h
Data 85h
Data 10h
70h
Read
Code
Copy Back
Code
Unlimited number of repetitions
tBLBH1
tBLBH2
(Read Busy time)
(Program Busy time)
RB
Busy
Busy
ai11001
30/64
NAND01G-B, NAND02G-B
Device operations
6.5
Cache Program
The Cache Program operation is used to improve the programming throughput by
programming data using the Cache Register. The Cache Program operation can only be
used within one block. The Cache Register allows new data to be input while the previous
data that was transferred to the Page Buffer is programmed into the memory array.
Each Cache Program operation consists of five steps (refer to Figure 14):
1. First of all the program setup command is issued (one bus cycle to issue the program
setup command then four bus write cycles to input the address), the data is then input
(up to 2112 Bytes/ 1056 Words) and loaded into the Cache Register.
2. One bus cycle is required to issue the confirm command to start the P/E/R Controller.
3. The P/E/R Controller then transfers the data to the Page Buffer. During this the device
is busy for a time of tWHBH2
.
4. Once the data is loaded into the Page Buffer the P/E/R Controller programs the data
into the memory array. As soon as the Cache Registers are empty (after tWHBH2) a new
Cache program command can be issued, while the internal programming is still
executing.
Once the program operation has started the Status Register can be read using the Read
Status Register command. During Cache Program operations SR5 can be read to find out
whether the internal programming is ongoing (SR5 = ‘0’) or has completed (SR5 = ‘1’) while
SR6 indicates whether the Cache Register is ready to accept new data. If any errors have
been detected on the previous page (Page N-1), the Cache Program Error Bit SR1 will be set
to ‘1', while if the error has been detected on Page N the Error Bit SR0 will be set to '1’.
When the next page (Page N) of data is input with the Cache Program command, tWHBH2 is
affected by the pending internal programming. The data will only be transferred from the
Cache Register to the Page Buffer when the pending program cycle is finished and the Page
Buffer is available.
If the system monitors the progress of the operation using only the Ready/Busy signal, the
last page of data must be programmed with the Page Program confirm command (10h).
If the Cache Program confirm command (15h) is used instead, Status Register bit SR5 must
be polled to find out if the last programming is finished before starting any other operations.
Figure 14. Cache Program Operation
tBLBH5
tBLBH5
tCACHEPG
(Cache Busy time)
RB
Busy
Busy
10h
Busy
Address Data
Inputs Inputs
Address Data
Inputs Inputs
Address Data
Inputs Inputs
I/O
80h
15h
80h
15h
80h
70h SR0
Cache Program
Confirm Code
Page
Program
Confirm Code
Read Status
Register
Page
Program
Code
Cache
Page
Program Program
Code
Code
First Page
Second Page
Last Page
(can be repeated up to 63 times)
ai08672
1. Up to 64 pages can be programmed in one Cache Program operation.
2. is the program time for the last page + the program time for the (last −1) page −(Program command cycle time
th
t
CACHEPG
+ Last page data loading time).
31/64
Device operations
NAND01G-B, NAND02G-B
6.6
Block Erase
Erase operations are done one block at a time. An erase operation sets all of the bits in the
addressed block to ‘1’. All previous data in the block is lost.
An erase operation consists of three steps (refer to Figure 15):
1. One bus cycle is required to setup the Block Erase command. Only addresses A18-
A28 (x8) or A17-A27 (x16) are used, the other address inputs are ignored.
2. two or three bus cycles are then required to load the address of the block to be erased.
Refer to Table 8 and Table 9 for the block addresses of each device.
3. one bus cycle is required to issue the Block Erase confirm command to start the P/E/R
Controller.
The operation is initiated on the rising edge of write Enable, W, after the confirm command
is issued. The P/E/R Controller handles Block Erase and implements the verify process.
During the Block Erase operation, only the Read Status Register and Reset commands will
be accepted, all other commands will be ignored.
Once the program operation has completed the P/E/R Controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High. If the operation completed successfully, the Write Status Bit
SR0 is ‘0’, otherwise it is set to ‘1’.
Figure 15. Block Erase Operation
tBLBH3
(Erase Busy time)
RB
Busy
Block Address
Inputs
I/O
60h
D0h
70h
SR0
Confirm
Code
Read Status Register
Block Erase
Setup Code
ai07593
6.7
Reset
The Reset command is used to reset the Command Interface and Status Register. If the
Reset command is issued during any operation, the operation will be aborted. If it was a
program or erase operation that was aborted, the contents of the memory locations being
modified will no longer be valid as the data will be partially programmed or erased.
If the device has already been reset then the new Reset command will not be accepted.
The Ready/Busy signal goes Low for tBLBH4 after the Reset command is issued. The value
of tBLBH4 depends on the operation that the device was performing when the command was
issued, refer to Table 25: AC Characteristics for Operations for the values.
32/64
NAND01G-B, NAND02G-B
Device operations
6.8
Read Status Register
The device contains a Status Register which provides information on the current or previous
Program or Erase operation. The various bits in the Status Register convey information and
errors on the operation.
The Status Register is read by issuing the Read Status Register command. The Status
Register information is present on the output data bus (I/O0-I/O7) on the falling edge of Chip
Enable or Read Enable, whichever occurs last. When several memories are connected in a
system, the use of Chip Enable and Read Enable signals allows the system to poll each
device separately, even when the Ready/Busy pins are common-wired. It is not necessary to
toggle the Chip Enable or Read Enable signals to update the contents of the Status
Register.
After the Read Status Register command has been issued, the device remains in Read
Status Register mode until another command is issued. Therefore if a Read Status Register
command is issued during a Random Read cycle a new Read command must be issued to
continue with a Page Read operation.
The Status Register bits are summarized in Table 13: Status Register Bits,. Refer to
Table 13 in conjunction with the following text descriptions.
6.8.1
6.8.2
Write Protection Bit (SR7)
The Write Protection bit can be used to identify if the device is protected or not. If the Write
Protection bit is set to ‘1’ the device is not protected and program or erase operations are
allowed. If the Write Protection bit is set to ‘0’ the device is protected and program or erase
operations are not allowed.
P/E/R Controller and Cache Ready/Busy Bit (SR6)
Status Register bit SR6 has two different functions depending on the current operation.
During Cache Program operations SR6 acts as a Cache Program Ready/Busy bit, which
indicates whether the Cache Register is ready to accept new data. When SR6 is set to '0',
the Cache Register is busy and when SR6 is set to '1', the Cache Register is ready to
accept new data.
During all other operations SR6 acts as a P/E/R Controller bit, which indicates whether the
P/E/R Controller is active or inactive. When the P/E/R Controller bit is set to ‘0’, the P/E/R
Controller is active (device is busy); when the bit is set to ‘1’, the P/E/R Controller is inactive
(device is ready).
6.8.3
P/E/R Controller Bit (SR5)
The Program/Erase/Read Controller bit indicates whether the P/E/R Controller is active or
inactive. When the P/E/R Controller bit is set to ‘0’, the P/E/R Controller is active (device is
busy); when the bit is set to ‘1’, the P/E/R Controller is inactive (device is ready).
33/64
Device operations
NAND01G-B, NAND02G-B
6.8.4
Cache Program Error Bit (SR1)
The Cache Program Error bit can be used to identify if the previous page (page N-1) has
been successfully programmed or not in a Cache Program operation. SR1 is set to ’1’ when
the Cache Program operation has failed to program the previous page (page N-1) correctly.
If SR1 is set to ‘0’ the operation has completed successfully.
The Cache Program Error bit is only valid during Cache Program operations, during other
operations it is Don’t Care.
6.8.5
6.8.6
Error Bit (SR0)
The Error bit is used to identify if any errors have been detected by the P/E/R Controller. The
Error Bit is set to ’1’ when a program or erase operation has failed to write the correct data to
the memory. If the Error Bit is set to ‘0’ the operation has completed successfully. The Error
Bit SR0, in a Cache Program operation, indicates a failure on Page N.
SR4, SR3 and SR2 are Reserved
Table 13. Status Register Bits
Bit
Name
Logic Level
Definition
'1'
Not Protected
Protected
SR7
Write Protection
'0'
'1'
P/E/R C inactive, device ready
Program/ Erase/ Read
Controller
'0'
P/E/R C active, device busy
SR6(1)
'1'
Cache Register ready (Cache Program only)
Cache Register busy (Cache Program only)
P/E/R C inactive, device ready
Cache Ready/Busy
'0'
'1'
Program/ Erase/ Read
Controller(2)
SR5
SR4, SR3, SR2
SR1
'0'
P/E/R C active, device busy
Reserved
Don’t Care
'1'
'0'
‘1’
‘0’
‘1’
‘0’
Page N-1 failed in Cache Program operation
Page N-1 programmed successfully
Error – operation failed
Cache Program Error(3)
Generic Error
No Error – operation successful
SR0(1)
Page N failed in Cache Program operation
Page N programmed successfully
Cache Program Error
1. The SR6 bit and SR0 bit have a different meaning during Cache Program and Cache Read operations.
2. Only valid for Cache Program operations, for other operations it is same as SR6.
3. Only valid for Cache Program operations, for other operations it is Don’t Care.
34/64
NAND01G-B, NAND02G-B
Device operations
6.9
Read Electronic Signature
The device contains a Manufacturer Code and Device Code. To read these codes three steps
are required:
1. one Bus Write cycle to issue the Read Electronic Signature command (90h)
2. one Bus Write cycle to input the address (00h)
3. four Bus Read Cycles to sequentially output the data (as shown in Table 14: Electronic
Signature).
Table 14. Electronic Signature
Byte/Word 1
Byte/Word 2
Device code
Part Number
Byte/Word 3
Byte/Word 4
Manufacturer
Code
NAND01GR3B
NAND01GW3B
NAND01GR4B
NAND01GW4B
NAND02GR3B
NAND02GW3B
NAND02GR4B
NAND02GW4B
A1h
F1h
B1h
C1h
AAh
DAh
BAh
CAh
20h
0020h
20h
Page Size
Spare Area size
Sequential Access
Time
Reserved
80h
Block Size
Organization
(seeTable 15)
0020h
Table 15. Electronic Signature Byte/Word 4
I/O
Definition
Value
Description
0 0
0 1
1 0
1 1
1K
Page Size
2K
I/O1-I/O0
(Without Spare Area)
Reserved
Reserved
Spare Area Size
(Byte / 512 Byte)
0
1
8
I/O2
I/O3
16
0
1
Standard (50 ns)
Sequential Access Time
Fast
(30 ns)
0 0
0 1
1 0
1 1
64K
Block Size
128K
256K
I/O5-I/O4
(Without Spare Area)
Reserved
0
1
X8
I/O6
I/O7
Organization
Not Used
X16
Reserved
35/64
Data protection
NAND01G-B, NAND02G-B
7
Data protection
The device has both hardware and software features to protect against program and erase
operations.
It features a Write Protect, WP, pin, which can be used to protect the device against program
and erase operations. It is recommended to keep WP at VIL during power-up and power-
down.
In addition, to protect the memory from any involuntary program/erase operations during
power-transitions, the device has an internal voltage detector which disables all functions
whenever VDD is below VLKO (see Table 22 and Table 23).
The device features a Block Lock mode, which is enabled by setting the Power-Up Read
Enable, Lock/Unlock Enable, PRL, signal to High.
The Block Lock mode has two levels of software protection.
●
●
Blocks Lock/Unlock
Blocks Lock-down
Refer to Figure 18 for an overview of the protection mechanism.
7.1
Blocks Lock
All the blocks are locked simultaneously by issuing a Blocks Lock command (see Table 10:
Commands).
All blocks are locked after power-up and when the Write Protect signal is Low.
Once all the blocks are locked, one sequence of consecutive blocks can be unlocked by
using the Blocks Unlock command.
Refer to Figure 23: Command Latch AC Waveforms for details on how to issue the
command.
7.2
Blocks Unlock
A sequence of consecutive locked blocks can be unlocked, to allow program or erase
operations, by issuing an Blocks Unlock command (see Table 10: Commands).
The Blocks Unlock command consists of four steps:
1. One bus cycle to setup the command
2. two or three bus cycles to give the Start Block Address (refer to Table 8, Table 9 and
Figure 16)
3. one bus cycle to confirm the command
4. two or three bus cycles to give the End Block Address (refer to Table 8, Table 9 and
Figure 16).
The Start Block Address must be nearer the logical LSB (Least Significant Bit) than End
Block Address.
36/64
NAND01G-B, NAND02G-B
Data protection
If the Start Block Address is the same as the End Block Address, only one block is unlocked.
Only one consecutive area of blocks can be unlocked at any one time. It is not possible to
unlock multiple areas.
Figure 16. Blocks Unlock Operation
WP
I/O
Add1
Add3
23h
Add1
Add3
24h
Add2
Add2
End Block Address, 3 cycles
Start Block Address, 3 cycles
Blocks Unlock
Command
ai08670
1. Three address cycles are required for 2 Gb devices. 1Gb devices only require two address cycles.
7.3
7.4
Blocks Lock-Down
The Lock-Down feature provides an additional level of protection. A Locked-down block
cannot be unlocked by a software command. Locked-Down blocks can only be unlocked by
setting the Write Protect signal to Low for a minimum of 100ns.
Only locked blocks can be locked-down. The command has no affect on unlocked blocks.
Refer to Figure 23: Command Latch AC Waveforms for details on how to issue the
command.
Block Lock Status
In Block Lock mode (PRL High) the Block Lock Status of each block can be checked by
issuing a Read Block Lock Status command (see Table 10: Commands).
The command consists of:
●
●
one bus cycle to give the command code
three bus cycles to give the block address
After this, a read cycle will then output the Block Lock Status on the I/O pins on the falling
edge of Chip Enable or Read Enable, whichever occurs last. Chip Enable or Read Enable
do not need to be toggled to update the status.
The Read Block Lock Status command will not be accepted while the device is busy (RB
Low).
The device will remain in Read Block Lock Status mode until another command is issued.
37/64
Data protection
NAND01G-B, NAND02G-B
Figure 17. Read Block Lock Status Operation
W
R
tWHRL
I/O
Add1
Add3
7Ah
Dout
Block Lock Status
Add2
Block Address, 3 cycles
Read Block Lock
Status Command
ai08669
1. Three address cycles are required for 2 Gb devices. 1Gb devices only require two address cycles.
Table 16. Block Lock Status
Status
I/O7-I/O3
I/O2
I/O1
I/O0
Locked
Unlocked
X
X
X
0
1
0
1
1
0
0
0
1
Locked-Down
Unlocked in
Locked-Down
Area
X
1
0
1
1. X = Don’t Care.
38/64
NAND01G-B, NAND02G-B
Data protection
Figure 18. Block Protection State Diagram
Power-Up
Block Unlock
Command
(start + end block address)
Locked
Blocks Lock-Down
Command
Blocks Lock
Command
WP V >100ns
IL
WP V >100ns
IL
Unlocked in
Locked Area
Locked-Down
WP V >100ns
IL
Unlocked in
Locked-Down
Area
Blocks Lock-Down
Command
AI08663c
1. PRL must be High for the software commands to be accepted.
39/64
Software algorithms
NAND01G-B, NAND02G-B
8
Software algorithms
This section gives information on the software algorithms that ST recommends to implement
to manage the Bad Blocks and extend the lifetime of the NAND device.
NAND Flash memories are programmed and erased by Fowler-Nordheim tunneling using a
high voltage. Exposing the device to a high voltage for extended periods can cause the
oxide layer to be damaged. For this reason, the number of program and erase cycles is
limited (see Table 18 for value) and it is recommended to implement Garbage Collection, a
Wear-Leveling Algorithm and an Error Correction Code, to extend the number of program
and erase cycles and increase the data retention.
To help integrate a NAND memory into an application ST Microelectronics can provide a File
System OS Native reference software, which supports the basic commands of file
management.
Contact the nearest ST Microelectronics sales office for more details.
8.1
Bad Block Management
Devices with Bad Blocks have the same quality level and the same AC and DC
characteristics as devices where all the blocks are valid. A Bad Block does not affect the
performance of valid blocks because it is isolated from the bit line and common source line
by a select transistor.
The devices are supplied with all the locations inside valid blocks erased (FFh). The Bad
Block Information is written prior to shipping. Any block, where the 1st and 6th Bytes, or 1st
Word, in the spare area of the 1st page, does not contain FFh, is a Bad Block.
The Bad Block Information must be read before any erase is attempted as the Bad Block
Information may be erased. For the system to be able to recognize the Bad Blocks based on
the original information it is recommended to create a Bad Block table following the
flowchart shown in Figure 19
8.2
Block Replacement
Over the lifetime of the device additional Bad Blocks may develop. In this case the block has
to be replaced by copying the data to a valid block. These additional Bad Blocks can be
identified as attempts to program or erase them will give errors in the Status Register.
As the failure of a page program operation does not affect the data in other pages in the
same block, the block can be replaced by re-programming the current data and copying the
rest of the replaced block to an available valid block. The Copy Back Program command can
be used to copy the data to a valid block.
See the Section 6.4: Copy Back Program for more details.
Refer to Table 17 for the recommended procedure to follow if an error occurs during an
operation.
40/64
NAND01G-B, NAND02G-B
Software algorithms
Table 17. Block Failure
Operation
Recommended Procedure
Erase
Program
Read
Block Replacement
Block Replacement or ECC
ECC
Figure 19. Bad Block Management Flowchart
START
Block Address =
Block 0
Increment
Block Address
Update
Bad Block table
Data
= FFh?
NO
NO
YES
Last
block?
YES
END
AI07588C
Figure 20. Garbage Collection
Old Area
New Area (After GC)
Valid
Page
Invalid
Page
Free
Page
(Erased)
AI07599B
41/64
Software algorithms
NAND01G-B, NAND02G-B
8.3
Garbage Collection
When a data page needs to be modified, it is faster to write to the first available page, and
the previous page is marked as invalid. After several updates it is necessary to remove
invalid pages to free some memory space.
To free this memory space and allow further program operations it is recommended to
implement a Garbage Collection algorithm. In a Garbage Collection software the valid
pages are copied into a free area and the block containing the invalid pages is erased (see
Figure 20).
8.4
Wear-leveling algorithm
For write-intensive applications, it is recommended to implement a Wear-leveling Algorithm
to monitor and spread the number of write cycles per block.
In memories that do not use a Wear-Leveling Algorithm not all blocks get used at the same
rate. Blocks with long-lived data do not endure as many write cycles as the blocks with
frequently-changed data.
The Wear-leveling Algorithm ensures that equal use is made of all the available write cycles
for each block. There are two wear-leveling levels:
●
First Level Wear-leveling, new data is programmed to the free blocks that have had the
fewest write cycles
●
Second Level Wear-leveling, long-lived data is copied to another block so that the
original block can be used for more frequently-changed data.
The Second Level Wear-leveling is triggered when the difference between the maximum
and the minimum number of write cycles per block reaches a specific threshold.
8.5
Error Correction Code
An Error Correction Code (ECC) can be implemented in the NAND Flash memories to
identify and correct errors in the data.
For every 2048 bits in the device it is recommended to implement 22 bits of ECC (16 bits for
line parity plus 6 bits for column parity).
An ECC model is available in VHDL or Verilog. Contact the nearest ST Microelectronics
sales office for more details.
42/64
NAND01G-B, NAND02G-B
Software algorithms
Figure 21. Error Detection
New ECC generated
during read
XOR previous ECC
with new ECC
NO
NO
>1 bit
= zero?
All results
= zero?
YES
YES
22 bit data = 0
11 bit data = 1
1 bit data = 1
ECC Error
Correctable
Error
No Error
ai08332
8.6
Hardware Simulation models
8.6.1
Behavioral simulation models
Denali Software Corporation models are platform independent functional models designed
to assist customers in performing entire system simulations (typical VHDL/Verilog). These
models describe the logic behavior and timings of NAND Flash devices, and so allow
software to be developed before hardware.
8.6.2
IBIS simulations models
IBIS (I/O Buffer Information Specification) models describe the behavior of the I/O buffers
and electrical characteristics of Flash devices.
These models provide information such as AC characteristics, rise/fall times and package
mechanical data, all of which are measured or simulated at voltage and temperature ranges
wider than those allowed by target specifications.
IBIS models are used to simulate PCB connections and can be used to resolve compatibility
issues when upgrading devices. They can be imported into SPICETOOLS.
43/64
Program and Erase Times and Endurance cycles
NAND01G-B, NAND02G-B
9
Program and Erase Times and Endurance cycles
The Program and Erase times and the number of Program/ Erase cycles per block are
shown in Table 18.
Table 18. Program, Erase Times and Program Erase Endurance Cycles
NAND Flash
Parameters
Unit
Min
Typ
Max
Page Program Time
300
2
700
3
µs
Block Erase Time
ms
Program/Erase Cycles (per block)
Data Retention
100,000
10
cycles
years
44/64
NAND01G-B, NAND02G-B
Maximum rating
10
Maximum rating
Stressing the device above the ratings listed in Table 19: Absolute Maximum Ratings, may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 19. Absolute Maximum Ratings
Value
Symbol
Parameter
Unit
Min
Max
TBIAS
TSTG
Temperature Under Bias
Storage Temperature
– 50
– 65
125
150
2.7
4.6
2.7
4.6
°C
°C
V
1.8V devices
3 V devices
1.8V devices
3 V devices
– 0.6
– 0.6
– 0.6
– 0.6
(1)
VIO
Input or Output Voltage
Supply Voltage
V
V
VDD
V
1. Minimum Voltage may undershoot to –2V for less than 20ns during transitions on input and I/O pins.
Maximum voltage may overshoot to V + 2V for less than 20ns during transitions on I/O pins.
DD
45/64
DC And AC parameters
NAND01G-B, NAND02G-B
11
DC And AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristics Tables that
follow, are derived from tests performed under the Measurement Conditions summarized in
Table 20: Operating and AC Measurement Conditions. Designers should check that the
operating conditions in their circuit match the measurement conditions when relying on the
quoted parameters.
Table 20. Operating and AC Measurement Conditions
NAND Flash
Parameter
Units
Min
Max
1.8V devices
3V devices
1.7
2.7
0
1.95
3.6
70
V
V
Supply Voltage (VDD
)
Grade 1
°C
°C
pF
pF
V
Ambient Temperature (TA)
Grade 6
–40
85
1.8V devices
3V devices (2.7 - 3.6V)
1.8V devices
3V devices
30
50
Load Capacitance (CL)
(1 TTL GATE and CL)
0
VDD
2.4
Input Pulses Voltages
0.4
V
1.8V devices
3V devices
0.9
1.5
8.35
5
V
Input and Output Timing Ref. Voltages
V
Output Circuit Resistor Rref
Input Rise and Fall Times
kΩ
ns
Table 21. Capacitance(1)
Symbol
Parameter
Test Condition
Typ
Max
Unit
CIN
Input Capacitance
VIN = 0V
10
10
pF
Input/Output
CI/O
VIL = 0V
pF
Capacitance(2)
1.
T = 25°C, f = 1 MHz. C and C are not 100% tested
A IN I/O
2. Input/output capacitances double in stacked devices
46/64
NAND01G-B, NAND02G-B
DC And AC parameters
Table 22. DC Characteristics, 1.8V Devices
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
tRLRL minimum
Sequential
Read
IDD1
-
8
15
mA
E=VIL, OUT = 0 mA
I
Operating
Current
IDD2
IDD3
Program
Erase
-
-
-
-
8
8
15
15
mA
mA
E=VDD-0.2,
WP=0/VDD
IDD5
Standby Current (CMOS)(1)
-
10
50
µA
ILI
ILO
Input Leakage Current(1)
Output Leakage Current(1)
Input High Voltage
VIN= 0 to VDDmax
-
-
-
±10
±10
µA
µA
V
VOUT= 0 to VDDmax
-
VIH
-
VDD-0.4
-
VDD+0.3
0.4
VIL
Input Low Voltage
-
-0.3
-
V
VOH
VOL
Output High Voltage Level
Output Low Voltage Level
Output Low Current (RB)
IOH = -100µA
IOL = 100µA
VOL = 0.1V
VDD-0.1
-
-
V
-
-
0.1
V
IOL (RB)
3
4
mA
VDD Supply Voltage (Erase and
Program lockout)
VLKO
-
-
-
1.1
V
1. Leakage current and standby current double in stacked devices
Figure 22. Equivalent Testing Circuit for AC Characteristics Measurement
V
DD
2R
ref
NAND Flash
C
L
2R
ref
GND
GND
Ai11085
47/64
DC And AC parameters
NAND01G-B, NAND02G-B
Table 23. DC Characteristics, 3V Devices
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
tRLRL minimum
Sequential
Read
IDD1
-
15
30
mA
E=VIL, OUT = 0 mA
I
Operating
Current
IDD2
IDD3
Program
Erase
-
-
-
-
15
15
30
30
1
mA
mA
mA
I
Standby current (TTL)(1)
E=VIH, WP=0/VDD
DD4
E=VDD-0.2,
WP=0/VDD
IDD5
Standby Current (CMOS)(1)
-
10
50
µA
ILI
ILO
Input Leakage Current(1)
Output Leakage Current(1)
Input High Voltage
VIN= 0 to VDDmax
-
-
-
±10
±10
µA
µA
V
VOUT= 0 to VDDmax
-
0.8VDD
-0.3
2.4
-
VIH
-
-
VDD+0.3
0.2VDD
-
VIL
Input Low Voltage
-
-
V
VOH
VOL
Output High Voltage Level
Output Low Voltage Level
Output Low Current (RB)
IOH = -400µA
IOL = 2.1mA
VOL = 0.4V
-
V
-
0.4
V
IOL (RB)
8
10
mA
VDD Supply Voltage (Erase and
Program lockout)
VLKO
-
-
-
1.7
V
1. Leakage current and standby current double in stacked devices
48/64
NAND01G-B, NAND02G-B
DC And AC parameters
Table 24. AC Characteristics for Command, Address, Data Input
Alt.
1.8V
3V
Symbol
Parameter
Unit
Symbol
Devices Devices
tALLWL
tALHWL
Address Latch Low to Write Enable Low
Address Latch High to Write Enable Low
tALS
AL Setup time
CL Setup time
Min
Min
0
0
0
0
ns
Command Latch High to Write Enable
Low
tCLHWL
tCLS
ns
tCLLWL
tDVWH
tELWL
Command Latch Low to Write Enable Low
Data Valid to Write Enable High
tDS
tCS
Data Setup time Min
20
0
20
0
ns
ns
ns
Chip Enable Low to Write Enable Low
E Setup time
Min
Min
tWHALH
tALH
Write Enable High to Address Latch High AL Hold time
10
10
Write Enable High to Command Latch
High
tWHCLH
tWHCLL
tCLH
CL hold time
Min
10
10
ns
Write Enable High to Command Latch
Low
tWHDX
tWHEH
tDH
tCH
Write Enable High to Data Transition
Write Enable High to Chip Enable High
Data Hold time
E Hold time
Min
Min
10
10
10
10
ns
ns
W High Hold
time
tWHWL
tWH
Write Enable High to Write Enable Low
Min
Min
20
20
ns
tWLWH
tWP
tWC
Write Enable Low to Write Enable High
Write Enable Low to Write Enable Low
W Pulse Width
25
60
25
50
ns
ns
(1)
tWLWL
Write Cycle time Min
1. If t
is less than 10ns, t
must be minimum 35ns, otherwise, t
may be minimum 25ns.
ELWL
WLWH
WLWH
49/64
DC And AC parameters
NAND01G-B, NAND02G-B
Table 25. AC Characteristics for Operations(1)(2)
Alt.
1.8V
3V
Symbol
Parameter
Unit
Symbol
Devices Devices
tALLRL1
tALLRL2
tBHRL
Read Electronic Signature
Read cycle
Min
Min
10
10
20
25
700
3
10
10
20
25
700
3
ns
ns
ns
µs
µs
ms
µs
µs
µs
µs
µs
µs
ns
ns
ns
ns
Address Latch Low to
Read Enable Low
tAR
tRR
Ready/Busy High to Read Enable Low
Read Busy time
Min
tBLBH1
tBLBH2
tBLBH3
tBLBH4
Max
Max
Max
Max
Typ
tPROG
tBERS
Program Busy time
Erase Busy time
Ready/Busy Low to
Ready/Busy High
Reset Busy time, during ready
5
5
3
3
tBLBH5
tCBSY
Cache Busy time
Max
Max
Max
Max
Min
700
5
700
5
Reset Busy time, during read
Reset Busy time, during program
Reset Busy time, during erase
Write Enable High to
Ready/Busy High
tWHBH1
tRST
10
500
10
0
10
500
10
0
tCLLRL
tDZRL
tEHQZ
tELQV
tCLR
tIR
tCHZ
tCEA
Command Latch Low to Read Enable Low
Data Hi-Z to Read Enable Low
Chip Enable High to Output Hi-Z
Chip Enable Low to Output Valid
Read Enable High to
Min
Max
Max
20
45
20
45
tRHRL
tREH
Read Enable High Hold time
Min
Min
20
15
20
15
ns
ns
Read Enable Low
TEHQX
TRHQX
TOH
Chip Enable high or Read Enable high to Output Hold
Read Enable Low to
Read Enable Pulse Width
Read Enable High
tRLRH
tRLRL
tRP
tRC
Min
Min
25
60
25
50
ns
ns
Read Enable Low to
Read Cycle time
Read Enable Low
Read Enable Access time
Read Enable Low to
Read ES Access time(3)
Output Valid
tRLQV
tREA
Max
Max
35
25
35
25
ns
µs
Write Enable High to
Read Busy time
tWHBH
tR
Ready/Busy High
tWHBL
tWHRL
tWB
Write Enable High to Ready/Busy Low
Write Enable High to Read Enable Low
Max
Min
100
60
100
60
ns
ns
tWHR
Write Enable Low to
Write Cycle time
Write Enable Low
tWLWL
tWC
Min
60
50
ns
1. The time to Ready depends on the value of the pull-up resistor tied to the Ready/Busy pin. See Figure 33, Figure 34 and
Figure 35.
2. To break the sequential read cycle, E must be held High for longer than t
3. ES = Electronic Signature.
.
EHEL
50/64
NAND01G-B, NAND02G-B
DC And AC parameters
Figure 23. Command Latch AC Waveforms
CL
tCLHWL
tWHCLL
(CL Setup time)
(CL Hold time)
tWHEH
(E Hold time)
tELWL
(E Setup time)
E
tWLWH
W
tALLWL
tWHALH
(ALSetup time)
(AL Hold time)
AL
tDVWH
(Data Setup time)
tWHDX
(Data Hold time)
I/O
Command
ai08028
Figure 24. Address Latch AC Waveforms
tCLLWL
(CL Setup time)
CL
tELWL
tWLWL
tWLWL
tWLWL
(E Setup time)
E
tWLWH
tWLWH
tWLWH
tWLWH
W
tWHWL
tWHALL
tALHWL
tWHWL
tWHALL
tWHWL
tWHALL
(AL Setup time)
(AL Hold time)
AL
I/O
tDVWH
tDVWH
tDVWH
tWHDX
tDVWH
tWHDX
(Data Setup time)
tWHDX
tWHDX
(Data Hold time)
Adrress
cycle 3
Adrress
cycle 2
Adrress
cycle 4
Adrress
cycle 1
ai08029
1. A fifth address cycle is required for 2Gb devices.
51/64
DC And AC parameters
NAND01G-B, NAND02G-B
Figure 25. Data Input Latch AC Waveforms
tWHCLH
(CL Hold time)
CL
E
tWHEH
(E Hold time)
tALLWL
tWLWL
(ALSetup time)
AL
W
tWLWH
tWLWH
tWLWH
tDVWH
tDVWH
tWHDX
tDVWH
tWHDX
(Data Setup time)
tWHDX
(Data Hold time)
Data In
Last
I/O
Data In 0
Data In 1
ai08030
1. Data In Last is 2112 in x8 devices and 1056 in x16 devices.
Figure 26. Sequential Data Output after Read AC Waveforms
tRLRL
(Read Cycle time)
E
tRHRL
(R High Holdtime)
tEHQZ
R
tRHQZ
tRHQZ
tRLQV
tRLQV
tRLQV
(R Accesstime)
I/O
RB
Data Out
Data Out
Data Out
tBHRL
ai08031
1. CL = Low, AL = Low, W = High.
52/64
NAND01G-B, NAND02G-B
DC And AC parameters
Figure 27. Read Status Register AC Waveform
tCLLRL
CL
tWHCLL
tWHEH
tCLHWL
E
tELWL
tWLWH
W
R
tELQV
tWHRL
tEHQZ
tDZRL
tWHDX
tDVWH
(Data Setup time)
tRLQV
tRHQZ
(Data Hold time)
70h/ 72h/
73h/ 74h/ 75h
Status Register
Output
I/O
ai08666
Figure 28. Read Electronic Signature AC Waveform
CL
E
W
AL
tALLRL1
R
tRLQV
(Read ES Access time)
I/O
90h
00h
Byte1
Byte2
Byte3
00h
Byte4
Man.
code
Device
code
Read Electronic 1st Cycle
Signature
Command
see Note.1
Address
ai08667
1. Refer to Table 14 for the values of the Manufacturer and Device Codes, and to Table 15 for the information contained in
Byte4.
53/64
DC And AC parameters
NAND01G-B, NAND02G-B
Figure 29. Page Read Operation AC Waveform
CL
tEHEL
tEHQZ
tEHBH
E
tWLWL
W
tWHBL
AL
tALLRL2
tWHBH
tRLRL
tRHQZ
tRHBL
(Read Cycle time)
R
tRLRH
tBLBH1
RB
Add.N
cycle 4
Data
N
Data
N+1
Data
N+2
Data
Last
Add.N
cycle 1
Add.N
cycle 3
Add.N
cycle 2
I/O
00h
30h
Data Output
from Address N to Last Byte or Word in Page
Command Address N Input
Code
Busy
ai08660
1. A fifth address cycle is required for 2Gb devices.
54/64
NAND01G-B, NAND02G-B
DC And AC parameters
Figure 30. Page Program AC Waveform
CL
E
tWLWL
tWLWL
tWLWL
(Write Cycle time)
W
tWHBL
tBLBH2
(Program Busy time)
AL
R
Add.N
Add.N Add.N
cycle 1 cycle 2
Add.N
cycle 3
I/O
RB
80h
Last
N
10h
70h
SR0
cycle 4
Confirm
Code
Page Program
Setup Code
Page
Program
Address Input
Data Input
Read Status Register
ai08668
1. A fifth address cycle is required for 2Gb devices.
55/64
DC And AC parameters
NAND01G-B, NAND02G-B
Figure 31. Block Erase AC Waveform
CL
E
tWLWL
(Write Cycle time)
W
AL
R
tBLBH3
tWHBL
(Erase Busy time)
Add.
Add.
Add.
I/O
RB
70h
SR0
60h
D0h
cycle 1 cycle 2
cycle 3
Block Erase
Setup Command
Confirm
Code
Block Erase
Read Status Register
Block Address Input
ai08038b
1. Address cycle 3 is required for 2Gb devices only.
Figure 32. Reset AC Waveform
W
AL
CL
R
I/O
RB
FFh
tBLBH4
(Reset Busy time)
ai08043
56/64
NAND01G-B, NAND02G-B
DC And AC parameters
11.1
Ready/Busy Signal electrical characteristics
Figure 34, Figure 33 and Figure 35 show the electrical characteristics for the Ready/Busy
signal. The value required for the resistor RP can be calculated using the following equation:
(
–
)
V
V
DDmax
OLmax
+ I
R min= -------------------------------------------------------------
P
I
L
OL
So,
1.85V
R min(1.8V)= ---------------------------
P
+
3mA
I
L
3.2V
R min(3V)= ---------------------------
P
+
8mA
I
L
where IL is the sum of the input currents of all the devices tied to the Ready/Busy signal. RP
max is determined by the maximum value of tr.
Figure 33. Ready/Busy AC Waveform
ready V
DD
V
OH
V
OL
busy
t
t
r
f
AI07564B
Figure 34. Ready/Busy Load Circuit
ibusy
R
P
V
DD
DEVICE
RB
Open Drain Output
V
SS
AI07563B
57/64
DC And AC parameters
NAND01G-B, NAND02G-B
Figure 35. Resistor Value Versus Waveform Timings For Ready/Busy Signal
V
= 1.8V, C = 30pF
V = 3.3V, C = 100pF
DD L
DD
L
400
300
200
400
300
200
4
3
2
4
3
2
400
300
2.4
200
1.7
120
1.2
100
0
1
100
0
1
0.85
0.8
100
3.6
90
0.57
0.6
3.6
60
1.7
0.43
1.7
30
1.7
3.6
3.6
1.7
1
2
3
4
1
2
3
4
R
(KΩ)
R (KΩ)
P
P
t
t
r
ibusy
f
ai07565B
1. T = 25°C.
11.2
Data Protection
The ST NAND device is designed to guarantee Data Protection during Power Transitions.
A VDD detection circuit disables all NAND operations, if VDD is below the VLKO threshold.
In the VDD range from VLKO to the lower limit of nominal range, the WP pin should be kept
low (VIL) to guarantee hardware protection during power transitions as shown in the below
figure.
Figure 36. Data Protection
Nominal Range
V
DD
V
LKO
Locked
Locked
W
Ai11086
58/64
NAND01G-B, NAND02G-B
Package mechanical
12
Package mechanical
Figure 37. TSOP48 - 48 lead Plastic Thin Small Outline, 12 x 20 mm, Package Outline
1
48
e
D1
B
L1
24
25
A2
A
E1
E
A1
α
L
DIE
C
CP
TSOP-G
1. Drawing is not to scale.
Table 26. TSOP48 - 48 lead Plastic Thin Small Outline, 12 x 20 mm, Package Mechanical Data
millimeters
inches
Symbol
Typ
Min
Max
Typ
Min
Max
A
A1
A2
B
1.200
0.150
1.050
0.270
0.210
0.080
12.100
20.200
18.500
–
0.0472
0.0059
0.0413
0.0106
0.0083
0.0031
0.4764
0.7953
0.7283
0.100
1.000
0.220
0.050
0.950
0.170
0.100
0.0039
0.0394
0.0087
0.0020
0.0374
0.0067
0.0039
C
CP
D1
E
12.000
20.000
18.400
0.500
0.600
0.800
3°
11.900
19.800
18.300
–
0.4724
0.7874
0.7244
0.0197
0.0236
0.0315
3°
0.4685
0.7795
0.7205
–
E1
e
L
0.500
0.700
0.0197
0.0276
5°
L1
a
0°
5°
0°
59/64
Package mechanical
NAND01G-B, NAND02G-B
Figure 38. VFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Outline
D
D2
D1
FD1
SD
FD
e
e
SE
E
E2 E1
ddd
BALL "A1"
FE1
FE
e
b
A
A2
A1
BGA-Z67
1. Drawing is not to scale
Table 27. VFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Mechanical Data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
A2
b
1.05
0.0413
0.25
0.0098
0.70
0.50
9.60
0.0276
0.0197
0.3780
0.45
9.50
4.00
7.20
0.40
9.40
0.0177
0.3740
0.1575
0.2835
0.0157
0.3701
D
D1
D2
ddd
E
0.10
0.0039
0.4764
12.00
5.60
8.80
0.80
2.75
1.15
3.20
1.60
0.40
0.40
11.90
–
12.10
0.4724
0.2205
0.3465
0.0315
0.1083
0.0453
0.1260
0.0630
0.0157
0.0157
0.4685
E1
E2
e
–
–
–
FD
FD1
FE
FE1
SD
SE
60/64
NAND01G-B, NAND02G-B
Package mechanical
Figure 39. TFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Outline
D
D2
D1
FD1
SD
FD
e
e
SE
E
E2 E1
ddd
BALL "A1"
FE1
FE
e
b
A
A2
A1
1. Drawing is not to scale
Table 28. TFBGA63 9.5x12mm - 6x8 active ball array, 0.80mm pitch, Package Mechanical Data
millimeters
Min
inches
Min
Symbol
Typ
Max
Typ
Max
A
A1
A2
b
1.20
0.0472
0.25
0.0098
0.80
0.45
9.50
4.00
7.20
0.0315
0.0177
0.3740
0.1575
0.2835
0.40
9.40
0.50
9.60
0.0157
0.3701
0.0197
0.3780
D
D1
D2
ddd
E
0.10
0.0039
0.4764
12.00
5.60
8.80
0.80
2.75
1.15
3.20
1.60
0.40
0.40
11.90
–
12.10
0.4724
0.2205
0.3465
0.0315
0.1083
0.0453
0.1260
0.0630
0.0157
0.0157
0.4685
E1
E2
e
–
–
–
FD
FD1
FE
FE1
SD
SE
61/64
Part numbering
NAND01G-B, NAND02G-B
13
Part numbering
Table 29. Ordering Information Scheme
Example:
NAND02GR3B
2
A
N
6
E
Device Type
NAND Flash Memory
Density
01G = 1Gb
02G = 2Gb
Operating Voltage
R = VDD = 1.7 to 1.95V
W = VDD = 2.7 to 3.6V
Bus Width
3 = x8
4 = x16
Family Identifier
B = 2112 Bytes/ 1056 Word Page
Device Options
2 = Chip Enable Don't Care Enabled
Product Version
A = First Version
B= Second Version
C= Third Version
Package
N = TSOP48 12 x 20mm (all devices)
ZA = VFBGA63 9.5 x 12 x 1mm, 0.8mm pitch (1Gb devices)
ZB = TFBGA63 9.5 x 12 x 1.2mm, 0.8mm pitch (2Gb Dual Die devices)
Temperature Range
1 = 0 to 70 °C
6 = –40 to 85 °C
Option
E = Lead Free Package, Standard Packing
F = Lead Free Package, Tape & Reel Packing
Devices are shipped from the factory with the memory content bits, in valid blocks, erased to
’1’. For further information on any aspect of this device, please contact your nearest ST
Sales Office.
62/64
NAND01G-B, NAND02G-B
Revision history
14
Revision history
Table 30. Document Revision History
Date
Version
Revision Details
25-Feb-2005
1
First Issue
Automatic Page 0 Read feature removed throughout document.
LFBGA63 package removed throughout document.
Section 11.2: Data Protection and Figure 22: Equivalent Testing
Circuit for AC Characteristics Measurement added.
TFBGA63 and VFBGA63 packages updated. Note added to Figure 3:
TSOP48 Connections, x8 devices and Table 3: TSOP48 Connections, x8
devices regarding the USOP package.
16-Aug-2005
2
Section 3.8: Write Enable (W), Table 11, Table 12, Table 14,
Section 7.4: Block Lock Status, Figure 18, Table 20, Table 22,
Table 23, Table 25 and Table 30 modified.
512 device and USOP package removed throughout document.
18-Oct-2005
13-Feb-2006
3
Figure 3, <Blue>Figure 5., Table 22, Table 23 and Section 6.4: Copy
Back Program modified.
4 Gbit and 8 Git devices removed.
4.0
VIH minimum value and VIL maximum value updated in Table 23: DC
Characteristics, 3V Devices.
63/64
NAND01G-B, NAND02G-B
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
64/64
相关型号:
NAND02GR4B2AZB1F
128MX16 FLASH 1.8V PROM, 25000ns, PBGA63, 9.50 X 12 MM, 1.20 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, TFBGA-63
STMICROELECTR
NAND02GR4B2AZB1T
128MX16 FLASH 1.8V PROM, 35ns, PBGA63, 9.50 X 12 MM, 1.20 MM HEIGHT, 0.80 MM PITCH, TFBGA-63
STMICROELECTR
NAND02GR4B2AZB6F
128MX16 FLASH 1.8V PROM, 25000ns, PBGA63, 9.50 X 12 MM, 1.20 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, TFBGA-63
STMICROELECTR
NAND02GR4B2AZB6T
128MX16 FLASH 1.8V PROM, 35ns, PBGA63, 9.50 X 12 MM, 1.20 MM HEIGHT, 0.80 MM PITCH, TFBGA-63
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明