P0115DA5AL3 [STMICROELECTRONICS]
0.8A, 400V, SCR, TO-92;型号: | P0115DA5AL3 |
厂家: | ST |
描述: | 0.8A, 400V, SCR, TO-92 栅 栅极 |
文件: | 总9页 (文件大小:83K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
P011xx
Sensitive high immunity SCRs up to 0.8 A
A
Features
■ IT(RMS) up to 0.8 A
■ VDRM/VRRM 400 and 600 V
■ IGT from 0.5 to 25 µA
G
K
Description
A
Thanks to highly sensitive triggering levels, the
P011xx SCR series is suitable for all applications
where available gate current is limited, such as
ground fault circuit interruptors, pilot circuits in
solid state relays, standby mode power supplies,
smoke and alarm detectors.
K
A
G
K
G
A
SOT-223
(P011xxN)
TO-92
(P011xxA)
Available in through-hole or surface-mount
packages, the voltage capability of this series has
been upgraded since its introduction and is now
available up to 600 V.
Table 1.
Device summary
Voltage
Sensitivity
Order code
Package
400 V
600 V
Min.
Max.
P0111DA 1AA3
X
X
X
4 µA
4 µA
4 µA
4 µA
4 µA
4 µA
25 µA
25 µA
25 µA
25 µA
25 µA
25 µA
50 µA
50 µA
5 µA
TO-92
TO-92
P0111DA 5AL3
P0111DN 5AA4
P0111MA 1AA3
P0111MA2AL3(1)
P0111MN 5AA4
P0115DA 1AA3
P0115DA 5AL3
P0118DA 1AA3
P0118DA 5AL3
P0118DN 5AA4
P0118MA 2AL3
P0118MA 5AL3
SOT-223
TO-92
X
X
X
TO-92
SOT-223
TO-92
X
X
X
X
X
15 µA
15 µA
0.5 µA
0.5 µA
0.5 µA
0.5 µA
0.5 µA
TO-92
TO-92
5 µA
TO-92
5 µA
SOT-223
TO-92
X
X
5 µA
5 µA
TO-92
1. This order code has no space.
January 2009
Rev 1
1/9
www.st.com
9
Characteristics
P011xx
1
Characteristics
Table 2.
Symbol
Absolute ratings (limiting values)
Parameter
Value
Unit
TO-92
Tl = 55 °C
IT(RMS) RMS on-state current (180° conduction angle)
0.8
A
SOT-223
TO-92
Tamb = 70 °C
Tl = 55 °C
IT(AV)
Average on-state current (180° conduction angle)
Non repetitive surge peak on-state current
0.5
A
A
SOT-223
tp = 8.3 ms
tp = 10 ms
tp = 10 ms
Tamb = 70 °C
8
7
ITSM
Tj = 25 °C
²
²
I t
I t Value for fusing
Tj = 25 °C
0.24
A2S
Critical rate of rise of on-state current
dI/dt
IGM
F = 60 Hz
tp = 20 µs
Tj = 125 °C
50
A/µs
I
G = 2 x IGT , tr ≤ 100 ns
Peak gate current
Tj = 125 °C
Tj = 125 °C
1
A
PG(AV) Average gate power dissipation
0.1
W
Tstg
Tj
Storage junction temperature range
Operating junction temperature range
- 40 to + 150
- 40 to + 125
°C
Table 3.
Symbol
Electrical characteristics (T = 25 °C, unless otherwise specified)
j
Test conditions
P0111
P0115
P0118
Unit
Min.
Max.
Max.
Min.
Min.
Max.
Max.
Min.
Max.
4
15
50
0.8
0.1
8
0.5
5
IGT
µA
VD = 12 V RL = 140 Ω
25
VGT
VGD
VRG
IH
V
V
VD = VDRM RL = 3.3 kΩ RGK = 1 kΩ
IRG = 10 µA
Tj = 125 °C
V
IT = 50 mA RGK = 1 kΩ
5
mA
mA
V/µs
V
IL
IG = 1 mA
RGK = 1 kΩ
6
dV/dt
VTM
Vt0
VD = 67 % VDRM RGK = 1 kΩ
ITM = 1.6 A tp = 380 µs
Tj = 125 °C
Tj = 25 °C
80
75
1.95
0.95
600
1
75
Threshold voltage
Tj = 125 °C Max.
Tj = 125 °C Max.
V
Rd
Dynamic resistance
mΩ
VDRM = VRRM = 400 V RGK = 1 kΩ
VDRM = VRRM = 600 V RGK = 1 kΩ
Tj = 25 °C
Max.
IDRM
IRRM
10
100
µA
VDRM = VRRM
RGK = 1 kΩ
Tj = 125 °C
2/9
P011xx
Characteristics
Table 4.
Symbol
Thermal resistance
Parameter
Maximum
Unit
Rth(j-a) Junction to case (DC)
Rth(j-t) Junction to tab (DC)
TO-92
SOT-223
80
30
°C/W
°C/W
TO-92
150
60
Rth(j-a) Junction to ambient (DC)
1. S = Copper surface under tab.
°C/W
S
(1) = 5 cm2 SOT-223
Figure 1.
Maximum average power
dissipation versus average on-state
current
Figure 2.
Average and DC on-state current
versus lead temperature
P(W)
I
(A)
T(AV)
1.0
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
D.C. (SOT-223)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
α = 180°
D.C. (TO-92)
α = 180° (SOT-223)
360°
α = 180° (TO-92)
I
(A)
T(AV)
T (°C)
lead
α
0
25
50
75
100
125
0.0
0.1
0.2
0.3
0.4
0.5
0.6
Figure 3.
Average and DC on-state current
versus ambient temperature
Figure 4.
Relative variation of thermal
impedance junction to ambient
versus pulse duration
K=[Z
/R
]
I
(A)
th(j-a) th(j-a)
T(AV)
1.00
0.10
0.01
1.2
1.1
Device mounted on FR4 with
recommended pad layout
D.C. (SOT-223)
D.C. (TO-92)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
TO-92
SOT-223
α = 180° (SOT-223)
α = 180° (TO-92)
t (s)
p
T
(°C)
amb
0
25
50
75
100
125
1E-2
1E-1
1E+0
1E+1
1E+2
5E+2
3/9
Characteristics
P011xx
Figure 5.
Relative variation of gate trigger,
holding and latching current versus
junction temperature
Figure 6.
Relative variation of holding
current versus gate-cathode
resistance (typical values)
I [R ] / I [R =1kΩ]
H
GK
H
GK
I
,I ,I [T ] / I ,I ,I [T =25°C]
GT
H
L
j
GT
H
L
j
20
18
16
14
12
10
8
6
5
4
3
2
1
0
Tj = 25°C
typical values
IGT
6
IH & IL
RGK = 1kΩ
4
T (°C)
j
2
R
GK
(kΩ)
0
1E-2
-40
-20
0
20
40
60
80
100
120
140
1E-1
1E+0
1E+1
Figure 7.
Relative variation of dV/dt immunity Figure 8.
versus gate-cathode resistance
(typical values).
Relative variation of dV/dt immunity
versus gate-cathode capacitance
(typical values)
dV/dt[C ] / dV/dt[R =1kΩ]
GK
GK
dV/dt[R ] / dV/dt[R =1kΩ]
GK
GK
10
8
10.0
VD = 0.67 x VDRM
Tj = 125°C
RGK = 1kΩ
Tj = 125°C
VD = 0.67 x VDRM
6
1.0
4
2
R
(kΩ)
GK
C
(nF)
GK
0.1
0
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0
1
2
3
4
5
6
7
Figure 9.
Surge peak on-state current versus Figure 10. Non-repetitive surge peak on-state
number of cycles
current and corresponding value
of I²t
I
(A), I2t (A2s)
TSM
I
(A)
TSM
100.0
10.0
8
7
6
5
4
3
2
1
0
Tj initial = 25°C
ITSM
tp=10ms
One cycle
sinusoidal pulse with
width tp < 10ms
Non repetitive
Tj initial=25°C
Repetitive
Tamb=25°C
1.0
0.1
I2t
t (ms)
p
Number of cycles
1
10
100
1000
0.01
10.00
1.00
0.10
4/9
P011xx
Ordering information scheme
Figure 11. On-state characteristics (maximum Figure 12. Thermal resistance junction to
values)
ambient versus copper surface
under tab
I
(A)
TM
R
(°C/W)
th(j-a)
1E+1
130
120
110
100
90
Tj max.:
Vt0=0.95V
Rd=600mΩ
Epoxy printed circuit board FR4,
copper thickness: 35 µm
1E+0
1E-1
Tj=max
80
70
60
Tj=25°C
50
40
30
20
10
0
S(cm²)
V (V)
TM
1E-2
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
2
Ordering information scheme
Figure 13. Ordering information scheme
P
01 1x
x
x
Blank
xAxx
Sensitive SCR series
Current
01 up to 0.8 A
Sensitivity
11 = 4 to 25 µA
15 = 15 to 50 µA
18 = 0.5 to 5 µA
Voltage
D = 400 V
M = 600 V
Package
A = TO-92
N = SOT-223
Packing mode
1AA3 = Bulk
2AL3 = Ammopack
5AL3 = Tape and reel 13 inch
5AA4 = Tape and reel 7 inch
5/9
Package information
P011xx
3
Package information
●
Epoxy meets UL94, V0
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
Table 5.
TO-92 dimensions
dimensions
Millimeters
Min Typ Max Min Typ Max
Ref
Inches
A
A
B
C
D
E
F
a
1.35
0.053
a
4.70
0.185
B
C
2.54
0.100
D
E
F
4.40
0.173
0.500
12.70
3.70
0.50
0.146
0.019
6/9
P011xx
Package information
Table 6.
SOT-223 dimensions
Dimensions
Millimeters
Min. Typ. Max. Min. Typ. Max.
1.80 0.071
Ref.
Inches
V
c
A
A1
B
A
A1
B
e1
0.02
0.001
0.60 0.70 0.80 0.024 0.027 0.031
D
B1
B1 2.90 3.00 3.10 0.114 0.118 0.122
c
D
e
0.24 0.26 0.32 0.009 0.010 0.013
6.30 6.50 6.70 0.248 0.256 0.264
4
E
H
2.3
4.6
0.090
0.181
1
2
3
e1
E
3.30 3.50 3.70 0.130 0.138 0.146
6.70 7.00 7.30 0.264 0.276 0.287
10° max
e
H
V
Figure 14. Footprint (dimensions in mm)
3.25
1.32
7.80
1.32
5.16
2.30
0.95
7/9
Ordering information
P011xx
4
Ordering information
Table 7.
Ordering information
Order code
Marking
Package
Weight Base qty
Packing mode
P0111DA 1AA3
P0111DA 5AL3
P0111DN 5AA4
P0111MA 1AA3
P0111MA2AL3(1)
P0111MN 5AA4
P0115DA 1AA3
P0115DA 5AL3
P0118DA 1AA3
P0118DA 5AL3
P0118DN 5AA4
P0118MA 2AL3
P0118MA 5AL3
P0111 DA
P0111 DA
P1D
TO-92
TO-92
0.2 g
0.2 g
0.11 g
0.2 g
0.2 g
0.11 g
0.2 g
0.2 g
0.2 g
0.2 g
0.11 g
0.2 g
0.2 g
2500
2000
1000
2500
2000
1000
2500
2000
2500
2000
1000
2000
2000
BAG
Tape and reel 13 inch
Tape and reel 7 inch
Bag
SOT-223
TO-92
P0111 MA
P0111 MA
P1M
TO-92
Ammopack
SOT-223
TO-92
Tape and reel 7 inch
Bag
P0115 DA
P0115 DA
P0118 DA
P0118 DA
P8D
TO-92
Tape and reel 13 inch
Bag
TO-92
TO-92
Tape and reel 13 inch
Tape and reel 7 inch
Ammopack
SOT-223
TO-92
P0118 MA
P0118 MA
TO-92
Tape and reel 13 inch
1. This order code has no space.
5
Revision history
Table 8.
Date
26-Jan-2009
Document revision history
Revision
Description of changes
1
First issue.
8/9
P011xx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
9/9
相关型号:
P01180NS100[OHM]
Passive Delay Line, 1-Func, 1-Tap, True Output, Hybrid, PDIP14, LOW PROFILE, PLASTIC, DIP-14
RCD
P01180NS200[OHM]
Passive Delay Line, 1-Func, 1-Tap, True Output, Hybrid, PDIP14, LOW PROFILE, PLASTIC, DIP-14
RCD
P01180NS300[OHM]
Passive Delay Line, 1-Func, 1-Tap, True Output, Hybrid, PDIP14, LOW PROFILE, PLASTIC, DIP-14
RCD
P01180NS500[OHM]
Passive Delay Line, 1-Func, 1-Tap, True Output, Hybrid, PDIP14, LOW PROFILE, PLASTIC, DIP-14
RCD
©2020 ICPDF网 联系我们和版权申明