PSD835F2V-A-70UI [STMICROELECTRONICS]
Configurable Memory System on a Chip for 8-Bit Microcontrollers; 片上可配置存储系统的8位微控制器型号: | PSD835F2V-A-70UI |
厂家: | ST |
描述: | Configurable Memory System on a Chip for 8-Bit Microcontrollers |
文件: | 总110页 (文件大小:565K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PSD835G2
Configurable Memory System on a Chip
for 8-Bit Microcontrollers
PRELIMINARY DATA
FEATURES SUMMARY
■ 5 V±10% Single Supply Voltage:
Figure 1. Packages
■ Up to 4 Mbit of Primary Flash Memory (8
uniform sectors)
■ 256Kbit Secondary Flash Memory (4 uniform
sectors)
■ Up to 64 Kbit SRAM
■ Over 3,000 Gates of PLD: DPLD and CPLD
■ 52 Reconfigurable I/O ports
■ Enhanced JTAG Serial Port
■ Programmable power management
■ High Endurance:
– 100,000 Erase/Write Cycles of Flash Memory
– 1,000 Erase/Write Cycles of PLD
TQFP80 (U)
January 2002
1/3
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
PSD8XX Family
PSD835G2
Configurable Memory System on a Chip
for 8-Bit Microcontrollers
The PSD8XX series of Programmable Microcontroller (MCU) Peripherals brings
In-System-Programmability (ISP) to Flash memory and programmable logic. The result is a
simple and flexible solution for embedded designs. PSD8XX devices combine many of the
peripheral functions found in MCU based applications:
1.0
Introduction
• 4 Mbit of Flash memory
• A secondary Flash memory for boot or data
• Over 3,000 gates of Flash programmable logic
• 64 Kbit SRAM
• Reconfigurable I/O ports
• Programmable power management.
1
PSD8XX Family
PSD835G2
The PSD835G2 device offers two methods to program PSD Flash memory while the PSD
is soldered to a circuit board.
1.0
Introduction
(Cont.)
❏ In-System Programming (ISP) via JTAG
An IEEE 1149.1 compliant JTAG-ISP interface is included on the PSD enabling the
entire device (both flash memories, the PLD, and all configuration) to be rapidly
programmed while soldered to the circuit board. This requires no MCU participation,
which means the PSD can be programmed anytime, even while completely blank.
The innovative JTAG interface to flash memories is an industry first, solving key
problems faced by designers and manufacturing houses, such as:
• First time programming – How do I get firmware into the flash the very first time?
JTAG is the answer, program the PSD while blank with no MCU involvement.
• Inventory build-up of pre-programmed devices – How do I maintain an accurate
count of pre-programmed flash memory and PLD devices based on customer
demand? How many and what version? JTAG is the answer, build your hardware
with blank PSDs soldered directly to the board and then custom program just before
they are shipped to customer. No more labels on chips and no more wasted
inventory.
• Expensive sockets – How do I eliminate the need for expensive and unreliable
sockets? JTAG is the answer. Solder the PSD directly to the circuit board. Program
first time and subsequent times with JTAG. No need to handle devices and bend the
fragile leads.
❏ In-Application re-Programming (IAP)
Two independent flash memory arrays are included so the MCU can execute code
from one memory while erasing and programming the other. Robust product firmware
updates in the field are possible over any communication channel (CAN, Ethernet,
UART, J1850, etc) using this unique architecture. Designers are relieved of these
problems:
• Simultaneous read and write to flash memory – How can the MCU program the
same memory from which it is executing code? It cannot. The PSD allows the MCU
to operate the two flash memories concurrently, reading code from one while erasing
and programming the other during IAP.
• Complex memory mapping – How can I map these two memories efficiently?
A Programmable Decode PLD is embedded in the PSD. The concurrent PSD
memories can be mapped anywhere in MCU address space, segment by segment
with extremely high address resolution. As an option, the secondary flash memory
can be swapped out of the system memory map when IAP is complete. A built-in
page register breaks the MCU address limit.
• Separate program and data space – How can I write to flash memory while it
resides in “program” space during field firmware updates, my 80C51 won’t allow it
The flash PSD provides means to “reclassify” flash memory as “data” space during
IAP, then back to “program” space when complete.
PSDsoft – ST’s software development tool – guides you through the design
process step-by-step making it possible to complete an embedded MCU design
capable of ISP/IAP in just hours. Select your MCU and PSDsoft will take you through
the remainder of the design with point and click entry, covering...PSD selection, pin
definitions, programmable logic inputs and outputs, MCU memory map definition, ANSI C
code generation for your MCU, and merging your MCU firmware with the PSD design.
When complete, two different device programmers are supported directly from PSDsoft –
FlashLINK (JTAG) and PSDpro.
The PSD835G2 is available in an 80-pin TQFP package.
Please refer to the revision block at the end of this
document for updated information.
2
PSD835G2
PSD8XX Family
❏ A simple interface to 8-bit microcontrollers that use either multiplexed or
non-multiplexed busses. The bus interface logic uses the control signals generated by
the microcontroller automatically when the address is decoded and a read or write is
performed. A partial list of the MCU families supported include:
2.0
Key Features
• Intel 8031, 80196, 80188, 80C251
• Motorola 68HC11 and 68HC16
• Philips 8031 and 80C51XA
• Zilog Z80, Z8 and Z180
• Infineon C500 family
❏ 4 Mbit Flash memory. This is the main Flash memory. It is divided into eight
equal-sized blocks that can be accessed with user-specified addresses.
❏ Internal secondary 256 Kbit Flash boot memory. It is divided into four equal-sized
blocks that can be accessed with user-specified addresses. This secondary memory
brings the ability to execute code and update the main Flash concurrently.
❏ 64 Kbit SRAM. The SRAM’s contents can be protected from a power failure by
connecting an external battery.
❏ CPLD with 16 Output Micro Cells (OMCs) and 24 Input Micro Cells (IMCs). The
CPLD may be used to efficiently implement a variety of logic functions for internal
and external control. Examples include state machines, loadable shift registers, and
loadable counters. The CPLD can also generate eight external chip selects.
❏ Decode PLD (DPLD) that decodes address for selection of internal memory blocks.
❏ 52 individually configurable I/O port pins that can be used for the following functions:
• MCU I/Os
• PLD I/Os
• Latched MCU address output
• Special function I/Os.
• I/O ports may be configured as open-drain outputs.
❏ Standby current as low as 50 µA for 5 V devices.
❏ Built-in JTAG compliant serial port allows full-chip In-System Programmability (ISP).
With it, you can program a blank device or reprogram a device in the factory or the field.
❏ Internal page register that can be used to expand the microcontroller address space
by a factor of 256.
❏ Internal programmable Power Management Unit (PMU) that supports a low power
mode called Power Down Mode. The PMU can automatically detect a lack of
microcontroller activity and put the PSD8XX into Power Down Mode.
❏ Erase/Write cycles:
• Flash memory – 100,000 minimum
• PLD – 1,000 minimum
3.0 PSD8XX
Series
Table 1. PSD8XX Product Matrix
Part #
Flash
Main
Flash
Boot
Memory
Kbit
Serial ISP Memory
PLD JTAG/ISP Kbit
PSD8XX
Series
I/O
PLD
Input
Output
SRAM
Kbit
Supply
Voltage
Device
Pins Inputs Macrocells Macrocells Outputs
Port
8 Sectors (4 Sectors)
PSD835G2
52
27
27
27
24
24
24
24
16
16
16
16
24
19
19
19
Yes
Yes
Yes
Yes
4096
1024
2048
1024
256
256
256
256
64
16
64
64
5V
5V
5V
5V
PSD8XX PSD813F2
PSD834F2
57
57
57
PSD833F2
3
ADDRESS/DATA/CONTROL BUS
PLD
INPUT
BUS
4 MBIT MAIN FLASH
MEMORY
PAGE
REGISTER
EMBEDDED
ALGORITHM
8 SECTORS
POWER
MANGMT
UNIT
VSTDBY
CNTL0,
CNTL1,
CNTL2
256 KBIT SECONDARY
FLASH MEMORY
(BOOT OR DATA)
4 SECTORS
(
)
PE6
SECTOR
SELECTS
PROG.
MCU BUS
INTRF.
FLASH DECODE
PLD DPLD
(
)
82
SECTOR
SELECTS
PROG.
PORT
64 KBIT BATTERY
BACKUP SRAM
PA0 – PA7
PB0 – PB7
PC0 – PC7
PD0 – PD3
PE0 – PE7
SRAM SELECT
PORT
A
PERIP I/O MODE SELECTS
CSIOP
AD0 – AD15
PF0 – PF7
PG0 – PG7
ADIO
PORT
RUNTIME CONTROL
AND I/O REGISTERS
PROG.
PORT
PORT
B
8 EXT CS to PORT C or F
FLASH ISP CPLD
(CPLD)
82
16 OUTPUT MICRO CELLS
PORT A & B
PROG.
PORT
PROG.
PORT
24 INPUT MICRO CELLS
PORT A ,B & C
PORT
F
PORT
C
CLKIN
PROG.
PORT
MICRO CELL FEEDBACK OR PORT INPUT
CLKIN
PORT F
PORT
D
PROG.
PORT
PORT
G
PROG.
PORT
PORT
E
GLOBAL
CONFIG. &
SECURITY
LOADER
JTAG
SERIAL
CHANNEL
PLD, CONFIGURATION
& FLASH MEMORY
CLKIN
*Additional address lines can be brought into PSD via Port A, B, C, D, or F.
PSD835G2
PSD8XX Family
PSD8XX devices contain several major functional blocks. Figure 1 on page 3 shows the
architecture of the PSD8XX device family. The functions of each block are described
briefly in the following sections. Many of the blocks perform multiple functions and are user
configurable.
4.0
PSD8XX
Architectural
Overview
4.1 Memory
The PSD835G2 contains the following memories:
• 4 Mbit Flash
• A secondary 256 Kbit Flash memory for boot or data
• 64 Kbit SRAM.
Each of the memories is briefly discussed in the following paragraphs. A more detailed
discussion can be found in section 9.
The 4 Mbit Flash is the main memory of the PSD835G2. It is divided into eight
equally-sized sectors that are individually selectable.
The 256 Kbit secondary Flash memory is divided into four equally-sized sectors. Each
sector is individually selectable.
The 64 Kbit SRAM is intended for use as a scratchpad memory or as an extension to the
microcontroller SRAM. If an external battery is connected to the PSD8XX’s Vstby pin, data
will be retained in the event of a power failure.
Each block of memory can be located in a different address space as defined by the user.
The access times for all memory types includes the address latching and DPLD decoding
time.
4.2 PLDs
The device contains two PLD blocks, each optimized for a different function, as shown in
Table 2. The functional partitioning of the PLDs reduces power consumption, optimizes
cost/performance, and eases design entry.
The Decode PLD (DPLD) is used to decode addresses and generate chip selects for the
PSD835G2 internal memory and registers. The CPLD can implement user-defined logic
functions. The DPLD has combinatorial outputs. The CPLD has 16 Output Micro Cells
and 8 combinatorial outputs. The PSD835G2 also has 24 Input Micro Cells that can be
configured as inputs to the PLDs. The PLDs receive their inputs from the PLD Input Bus
and are differentiated by their output destinations, number of Product Terms, and
Micro Cells.
The PLDs consume minimal power by using Zero-Power design techniques. The speed and
power consumption of the PLD is controlled by the Turbo Bit in the PMMR0 register and
other bits in the PMMR2 registers. These registers are set by the microcontroller at runtime.
There is a slight penalty to PLD propagation time when invoking the non-Turbo bit.
4.3 I/O Ports
The PSD835G2 has 52 I/O pins divided among seven ports (Port A, B, C, D, E, F and G).
Each I/O pin can be individually configured for different functions. Ports can be configured
as standard MCU I/O ports, PLD I/O, or latched address outputs for microcontrollers using
multiplexed address/data busses.
The JTAG pins can be enabled on Port E for In-System Programming (ISP). Ports F and
G can also be configured as a data port for a non-multiplexed bus.
4.4 Microcontroller Bus Interface
The PSD835G2 easily interfaces with most 8-bit microcontrollers that have either
multiplexed or non-multiplexed address/data busses. The device is configured to respond
to the microcontroller’s control signals, which are also used as inputs to the PLDs. Section
9.3.5 contains microcontroller interface examples.
Table 2. PLD I/O Table
Name
Decode PLD
Abbreviation
DPLD
Inputs
82
Outputs
17
Product Terms
43
Complex PLD
CPLD
82
24
150
5
PSD8XX Family
PSD835G2
PSD8XX
Architectural
Overview
(cont.)
4.5 ISP via JTAG Port
In-System Programming can be performed through the JTAG pins on Port E. This serial
interface allows complete programming of the entire PSD835G2 device. A blank device
can be completely programmed. The JTAG signals (TMS, TCK, TSTAT, TERR, TDI, TDO)
can be multiplexed with other functions on Port E. Table 3 indicates the JTAG signals pin
assignments.
4.6 In-System Programming (ISP)
Using the JTAG signals on Port E, the entire PSD835G2 (memory, logic, configuration)
device can be programmed or erased without the use of the microcontroller.
Table 3. JTAG Signals on Port E
Port E Pins
PE0
JTAG Signal
TMS
PE1
TCK
PE2
TDI
PE3
TDO
PE4
TSTAT
TERR
PE5
4.7 In-Application re-Programming (IAP)
The main Flash memory can also be programmed in-system by the microcontroller
executing the programming algorithms out of the secondary Flash memory, or SRAM.
Since this is a sizable separate block, the application can also continue to operate. The
secondary Flash boot memory can be programmed the same way by executing out of the
main Flash memory. Table 4 indicates which programming methods can program different
functional blocks of the PSD8XX.
Table 4. Methods of Programming Different Functional Blocks of the PSD835G2
Device
Programmer
Functional Block
JTAG-ISP
IAP
Main Flash memory
Flash Boot memory
PLD Array (DPLD and CPLD)
PSD Configuration
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
4.8 Page Register
The eight-bit Page Register expands the address range of the microcontroller by up to
256 times.The paged address can be used as part of the address space to access
external memory and peripherals or internal memory and I/O. The Page Register can also
be used to change the address mapping of blocks of Flash memory into different memory
spaces for IAP.
4.9 Power Management Unit
The Power Management Unit (PMU) in the PSD835G2 gives the user control of the
power consumption on selected functional blocks based on system requirements. The
PMU includes an Automatic Power Down unit (APD) that will turn off device functions due
to microcontroller inactivity. The APD unit has a Power Down Mode that helps reduce
power consumption.
The PSD835G2 also has some bits that are configured at run-time by the MCU to reduce
power consumption of the CPLD. The turbo bit in the PMMR0 register can be turned off
and the CPLD will latch its outputs and go to standby until the next transition on its inputs.
Additionally, bits in the PMMR2 register can be set by the MCU to block signals from
entering the CPLD to reduce power consumption. See section 9.5.
6
PSD835G2
PSD8XX Family
The PSD8XX series is supported by PSDsoft a Windows-based (95, 98, NT) software
development tool. A PSD design is quickly and easily produced in a point and click
environment. The designer does not need to enter Hardware Definition Language (HDL)
equations (unless desired) to define PSD pin functions and memory map information. The
general design flow is shown in Figure 2 below. PSDsoft is available from our web site
(www.st.com/psm) or other distribution channels.
5.0
Development
System
PSDsoft directly supports two low cost device programmers from ST. PSDpro
and FlashLINK (JTAG). Both of these programmers may be purchased through your local
rep/distributor, or directly from our web site using a credit card. The PSD8XX is also
supported by third party device programmers, see web site for current list.
Figure 2. PSDsoft Development Tool
Choose MCU and PSD
Automatically Configures MCU
bus interface and other PSD
attributes.
Define PSD Pin and
Node functions
Point and click definition of
PSD pin functions, internal nodes,
and MCU system memory map.
Define General Purpose
C Code Generation
Logic in CPLD
Point and click definition of
Generate C Code
combinatorial and registered logic
Specific to PSD
in CPLD. Access to HDL is
Finctions
available if needed.
Merge MCU Firmware
with PSD Configuration
User's choice of
Microcontroller
Compiler/Linker
MCU Firmware
A composite object file is created
containing MCU firmware and
PSD configuration.
Hex or S-Record
format
*.OBJ FILE
ST
*.OBJ file
available
PSD Programmer
for 3rd party
programmers
(Conventional or JTAG-ISP)
PSDPro or
FlashLink (JTAG)
7
PSD8XX Family
PSD835G2
The following table describes the pin names and pin functions of the PSD835G2. Pins that
have multiple names and/or functions are defined using PSDsoft.
6.0
Table 5.
PSD835G2
Pin
Pin*
(TQFP
Pkg.) Type
Pin Name
Description
Descriptions
ADIO0-7
3-7
10-12
I/O This is the lower Address/Data port. Connect your MCU
address or address/data bus according to the following rules:
1. If your MCU has a multiplexed address/data bus where the
data is multiplexed with the lower address bits, connect
AD[0:7] to this port.
2. If your MCU does not have a multiplexed address/data bus,
connect A[0:7] to this port.
3. If you are using an 80C51XA in burst mode, connect
A4/D0 through A11/D7 to this port.
ALE or AS latches the address. The PSD drives data out only
if the read signal is active and one of the PSD functional blocks
was selected. The addresses on this port are passed to the
PLDs.
ADIO8-15
13-20 I/O This is the upper Address/Data port. Connect your MCU
address or address/data bus according to the following rules:
1. If your MCU has a multiplexed address/data bus where the
data is multiplexed with the lower address bits, connect
A[8:15] to this port.
2. If your MCU does not have a multiplexed address/data bus,
connect A[8:15] to this port.
3. If you are using an 80C251 in page mode, connect AD[8:15]
to this port
4. If you are using an 80C51XA in burst mode, connect
A[12:19] to this port.
ALE or AS latches the address. The PSD drives data out only
if the read signal is active and one of the PSD functional
blocks was selected. The addresses on this port are passed
to the PLDs.
CNTL0
CNTL1
59
60
I
I
The following control signals can be connected to this port,
based on your MCU:
1. WR — active-low write input.
_
2. R W — active-high read/active low write input.
This pin is connected to the PLDs. Therefore, these signals can
be used in decode and other logic equations.
The following control signals can be connected to this port,
based on your MCU:
1. RD — active-low read input.
2. E — E clock input.
3. DS — active-low data strobe input.
4. PSEN — connect PSEN to this port when it is being used as
an active-low read signal. For example, when the 80C251
outputs more than 16 address bits, PSEN is actually the read
signal.
This pin is connected to the PLDs. Therefore, these signals can
be used in decode and other logic equations.
CNTL2
Reset
40
39
I
I
This pin can be used to input the PSEN (Program Select
Enable) signal from any MCU that uses this signal for code
exclusively. If your MCU does not output a Program Select
Enable signal, this port can be used as a generic input. This
port is connected to the PLD as input.
Active low input. Resets I/O Ports, PLD Micro Cells, some of
the configuration registers and JTAG registers. Must be active
at power up. Reset also aborts the Flash programming/erase
cycle that is in progress.
8
PSD835G2
PSD8XX Family
Table 5.
PSD835G2
Pin
Descriptions
(cont.)
Pin*
(TQFP
Pin Name Pkg.)
Type
Description
Port A, PA0-7. This port is pin configurable and has multiple
PA0-PA7 51-58
PB0-PB7 61-68
PC0-PC7 41-48
I/O
CMOS functions:
or Open 1. MCU I/O — standard output or input port
Drain
2. CPLD Micro Cell (MCell A0-7) output.
3. Latched, transparent or registered PLD input.
I/O
Port B, PB0-7. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. CPLD Micro Cell (MCell B0-7) output.
3. Latched, transparent or registered PLD input.
I/O
Port C, PC0-7. This port is pin configurable and has multiple
CMOS functions:
or Slew 1. MCU I/O — standard output or input port.
Rate
2. External chip select (ECS0-7) output.
3. Latched, transparent or registered PLD input.
PD0
PD1
PD2
79
80
1
I/O
Port D pin PD0 can be configured as:
CMOS 1. ALE or AS input — latches addresses on ADIO0-15 pins
or Open 2. AS input — latches addresses on ADIO0-15 pins on the
Drain
rising edge.
3. Input to the PLD.
4. Transparent PLD input.
I/O
Port D pin PD1 can be configured as:
CMOS 1. MCU I/O
or Open 2. Input to the PLD.
Drain
3. CLKIN clock input — clock input to the CPLD
Micro Cells, the APD power down counter and CPLD
AND Array.
I/O
Port D pin PD2 can be configured as:
CMOS 1. MCU I/O
or Open 2. Input to the PLD.
Drain
3. CSI input — chip select input. When low, the CSI enables
the internal PSD memories and I/O. When high, the
internal memories are disabled to conserve power. CSI
trailing edge can get the part out of power-down mode.
PD3
PE0
2
I/O
Port D pin PD3 can be configured as:
1. MCU I/O
2. Input to the PLD.
CMOS
or Open
Drain
71
I/O
Port E, PE0. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. TMS input for JTAG/ISP interface.
PE1
PE2
72
73
I/O
Port E, PE1. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. TCK input for JTAG/ISP interface (Schmidt Trigger).
I/O
Port E, PE2. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. TDI input for JTAG/ISP interface.
9
PSD8XX Family
PSD835G2
Table 5.
PSD835G2
Pin
Descriptions
(cont.)
Pin*
(TQFP
Pin Name Pkg.)
Type
Description
Port E, PE3. This port is pin configurable and has multiple
PE3
74
I/O
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. TDO output for JTAG/ISP interface.
PE4
75
I/O
Port E, PE4. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. TSTAT output for the ISP interface.
4. Rdy/Bsy — for in-circuit Parallel Programming.
PE5
PE6
76
77
I/O
Port E, PE5. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. TERR active low output for ISP interface.
I/O
Port E, PE6. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. Vstby — SRAM standby voltage input for battery
backup SRAM
PE7
78
I/O
Port E, PE7. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address output.
3. Vbaton — battery backup indicator output. Goes high when
power is drawn from an external battery.
PF0-PF7 31-38
PG0-PG7 21-28
I/O
Port F, PF0-7. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Input to the PLD.
3. Latched address outputs.
4. As address A0-3 inputs in 80C51XA mode
5. As data bus port (D0-7) in non-multiplexed bus configuration
I/O
Port G, PG0-7. This port is pin configurable and has multiple
CMOS functions:
or Open 1. MCU I/O — standard output or input port.
Drain
2. Latched address outputs.
GND
8,30,
49,50,
70
V
9,29,
69
CC
10
PSD835G2
PSD8XX Family
Table 6 shows the offset addresses to the PSD835G2 registers relative to the CSIOP base
address. The CSIOP space is the 256 bytes of address that is allocated by the user to the
internal PSD835G2 registers. Table 6 provides brief descriptions of the registers in CSIOP
space. For a more detailed description, refer to section 9.
7.0 PSD835G2
Register
Description and
Address Offset
Table 6. Register Address Offset
Register Name
Port A Port B Port C Port D Port E Port F Port G Other*
Description
Reads Port pin as input,
MCU I/O input mode
Data In
00
01
10
11
30
32
40
42
41
43
Selects mode between
MCU I/O or Address Out
Control
Stores data for output
to Port pins, MCU I/O
output mode
Data Out
Direction
04
06
05
07
14
16
15
17
34
36
44
46
45
47
Configures Port pin as
input or output
Configures Port pins as
either CMOS or Open
Drain on some pins, while
selecting high slew rate
on other pins.
Drive Select
08
09
18
19
1A
38
48
49
Input Micro Cell
Enable Out
0A
0C
0B
0D
Reads Input Micro Cells
Reads the status of the
output enable to the I/O
Port driver
1C
4C
Read – reads output of
Micro Cells A
Write – loads Micro cell
Flip-Flops
Output
Micro Cells A
20
Read – reads output of
Micro Cells B
Write – loads Micro cell
Flip-Flops
Output
Micro Cells B
21
23
Mask
Micro Cells A
Blocks writing to the
22
Output Micro Cells A
Mask
Micro Cells B
Blocks writing to the
Output Micro Cells B
C0
C2
Read only – Flash Sector
Protection
Flash Protection
Read only – PSD Security
and Flash Boot Sector
Protection
Flash Boot
Protection
JTAG Enable
PMMR0
C7
B0
Enables JTAG Port
Power Management
Register 0
Power Management
Register 2
PMMR2
Page
B4
E0
Page Register
Places PSD memory
areas in Program and/or
Data space on an
VM
E2
individual basis.
Read only – Flash and
SRAM size
Memory_ID0
Memory_ID1
F0
F1
Read only – Boot type
and size
11
PSD8XX Family
PSD835G2
All the registers in the PSD835G2 are included here for reference. Detail description of the
registers are found in the Functional Block section of the Data Sheet.
8.0
Register Bit
Definition
Data In Registers – Port A, B, C, D, E, F and G
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions:
Read only registers, read Port pin status when Port is in MCU I/O input Mode.
Data Out Registers – Port A, B, C, D, E, F and G
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions:
Latched data for output to Port pin when pin is configured in MCU I/O output mode.
Direction Registers – Port A, B, C, D, E, F and G
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions:
Set Register Bit to 0 = configure corresponding Port pin in Input mode (default).
Set Register Bit to 1 = configure corresponding Port pin in Output mode.
Control Registers – Ports E, F and G
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions:
Set Register Bit to 0 = configure corresponding Port pin in MCU I/O mode (default).
Set Register Bit to 1 = configure corresponding Port pin in Latched Address Out mode.
Drive Registers – Ports A, B, D, E, and G
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions:
Set Register Bit to 0 = configure corresponding Port pin in CMOS output driver (default).
Set Register Bit to 1 = configure corresponding Port pin in Open Drain output driver.
Drive Registers – Ports C and F
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions:
Set Register Bit to 0 = configure corresponding Port pin as CMOS output driver (default).
Set Register Bit to 1 = configure corresponding Port pin in Slew Rate mode.
Enable Out Registers – Ports A, B, C and F
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port Pin 7 Port Pin 6 Port Pin 5 Port Pin 4 Port Pin 3 Port Pin 2 Port Pin 1 Port Pin 0
Bit definitions: Read Only Registers
Register Bit <j> = 0 indicates Port pin driver is in tri-state mode (default).
Register Bit <j> = 1 indicates Port pin driver is enabled.
12
PSD835G2
PSD8XX Family
Input Micro Cells – Ports A, B and C
8.0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Register Bit
Definition
(cont.)
IMcell7
IMcell6
IMcell5
IMcell4
IMcell3
IMcell2
IMcell1
IMcell0
Bit definitions: Read Only Registers
Read Input Micro Cell[7:0] status on Ports A, B and C.
Output Micro Cells A Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mcella7
Mcella6
Mcella5
Mcella4
Mcella3
Mcella2
Mcella1
Mcella0
Bit definitions:
Write Register: Load Micro CellA[7:0] with 0 or 1.
Read Register: Read Micro CellA[7:0] output status.
Output Micro Cells B Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mcellb7
Mcellb6
Mcellb5
Mcellb4
Mcellb3
Mcellb2
Mcellb1
Mcellb0
Bit definitions:
Write Register: Load Micro CellB[7:0] with 0 or 1.
Read Register: Read Micro CellB[7:0] output status.
Mask Micro Cells A Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mcella7
Mcella6
Mcella5
Mcella4
Mcella3
Mcella2
Mcella1
Mcella0
Bit definitions:
Register Bit <j> to 0 = allow Micro CellA<j> flip flop to be loaded by MCU (default).
Register Bit <j> to 1 = does not allow Micro CellA<j> flip flop to be loaded by MCU.
Mask Micro Cells B Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mcellb7
Mcellb6
Mcellb5
Mcellb4
Mcellb3
Mcellb2
Mcellb1
Mcellb0
Bit definitions:
Register Bit <j> to 0 = allow Micro CellB<j> flip flop to be loaded by MCU (default).
Register Bit <j> to 1 = does not allow Micro CellB<j> flip flop to be loaded by MCU.
Flash Protection Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Sec7_Prot Sec6_Prot Sec5_Prot Sec4_Prot Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
Bit definitions: Read Only Register
Sec<i>_Prot
Sec<i>_Prot
1 = Flash Sector <i> is write protected.
0 = Flash Sector <i> is not write protected.
Flash Boot Protection Register
Bit 7
Bit 6
*
Bit 5
*
Bit 4
*
Bit 3
Bit 2
Bit 1
Bit 0
Security_Bit
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
Bit definitions:
Sec<i>_Prot
Sec<i>_Prot
1 = Boot Block Sector <i> is write protected.
0 = Boot Block Sector <i> is not write protected.
Security_Bit
0 = Security Bit in device has not been set.
1 = Security Bit in device has been set.
13
PSD8XX Family
PSD835G2
JTAG Enable Register
8.0
Bit 7
*
Bit 6
*
Bit 5
*
Bit 4
*
Bit 3
*
Bit 2
*
Bit 1
*
Bit 0
Register Bit
Definition
(cont.)
JTAG_Enable
Bit definitions:
JTAG_Enable 1 = JTAG Port is Enabled.
0 = JTAG Port is Disabled.
Page Register
Bit 7
Pgr7
Bit 6
Pgr6
Bit 5
Pgr5
Bit 4
Pgr4
Bit 3
Bit 2
Bit 1
Bit 0
Pgr0
Pgr3
Pgr2
Pgr1
Bit definitions:
Configure Page input to PLD. Default Pgr[7:0] = 00.
PMMR0 Register
Bit 7
*
Bit 6
*
Bit 5
Bit 4
Bit 3
Bit 2
*
Bit 1
Bit 0
*
PLD
Mcells clk
PLD
array-clk
PLD
Turbo
APD
enable
*Not used bit should be set to zero.
Bit definitions: (default is 0)
Bit 1 0 = Automatic Power Down (APD) is disabled.
1 = Automatic Power Down (APD) is enabled.
Bit 3 0 = PLD Turbo is on.
1 = PLD Turbo is off, saving power.
Bit 4 0 = CLKIN input to the PLD AND array is connected.
Every CLKIN change will power up the ZPLD when Turbo bit is off.
1 = CLKIN input to PLD AND array is disconnected, saving power.
Bit 5 0 = CLKIN input to the PLD Micro Cells is connected.
1 = CLKIN input to the PLD Micro Cells is disconnected, saving power.
PMMR1 Register
Bit 7
*
Bit 6
PLD
Bit 5
PLD
Bit 4
PLD
Bit 3
PLD
Bit 2
PLD
Bit 1
*
Bit 0
*
array WRh array Ale array Cntl2 array Cntl1 array Cntl0
*Not used bit should be set to zero.
Bit definitions (default is 0):
Bit 0 0 = Address A[7:0] are connected into the PLD array.
1 = Address A[7:0] are blocked from the PLD array, saving power.
Note: in XA mode, A3-0 come from PF3-0 and A7-4 come from ADIO7-4.
Bit 2 0 = Cntl0 input to the PLD AND array is connected.
1 = Cntl0 input to the PLD AND array is disconnected, saving power.
Bit 3 0 = Cntl1 input to the PLD AND array is connected.
1 = Cntl1 input to the PLD AND array is disconnected, saving power.
Bit 4 0 = Cntl2 input to the PLD AND array is connected.
1 = Cntl2 input to the PLD AND array is disconnected, saving power.
Bit 5 0 = Ale input to the PLD AND array is connected.
1 = Ale input to the PLD AND array is disconnected, saving power.
Bit 6 0 = WRh/DBE input to the PLD AND array is connected.
1 = WRh/DBE input to the PLD AND array is disconnected, saving power.
14
PSD835G2
PSD8XX Family
VM Register
8.0
Bit 7
Bit 6
*
Bit 5
*
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Register Bit
Definition
(cont.)
Periph-
mode
FL_data
Boot_data FL_code Boot_code SR_code
Note: Upon reset, Bit1-Bit4 are loaded to configurations selected by the user in PSDsoft. Bit 0 and Bit 7 are
always cleared by reset. Bit 0 to Bit 4 are active only when the device is configured in Philips 80C51XA
mode.
* Not used bit should be set to zero
Bit definitions:
Bit 0 0 = PSEN can’t access SRAM in 80C51XA modes.
1 = PSEN can access SRAM in 80C51XA modes.
Bit 1 0 = PSEN can’t access Boot in 80C51XA modes.
1 = PSEN can access Boot in 80C51XA modes.
Bit 2 0 = PSEN can’t access main Flash in 80C51XA modes.
1 = PSEN can access main Flash in 80C51XA modes.
Bit 3 0 = RD can’t access Boot in 80C51XA modes.
1 = RD can access Boot in 80C51XA modes.
Bit 4 0 = RD can’t access main Flash in 80C51XA modes.
1 = RD can access main Flash in 80C51XA modes.
Bit 7 0 = Peripheral mode of Port F is disabled.
1 = Peripheral mode of Port F is enabled.
Memory_ID0 Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
S_size 3
S_size 2
S_size 1
S_size 0
F_size 3
F_size 2
F_size 1
F_size 0
Bit definitions:
F_size[3:0] = 4h, main Flash size is 2M bit.
F_size[3:0] = 5h, main Flash size is 8M bit.
S_size[3:0] = 0h, SRAM size is 0K bit.
S_size[3:0] = 1h, SRAM size is 16K bit.
S_size[3:0] = 3h, SRAM size is 64K bit.
Memory_ID1 Register
Bit 7
*
Bit 6
*
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
B_type 1
B_type 0
B_size 3
B_size 2
B_size 1
B_size 0
*Not used bit should be set to zero.
Bit definitions:
B_size[3:0] = 0h, Boot block size is 0K bit.
B_size[3:0] = 2h, Boot block size is 256K bit.
B_type[1:0] = 0h, Boot block is Flash memory.
15
PSD8XX Family
PSD835G2
As shown in Figure 1, the PSD835G2 consists of six major types of functional blocks:
9.0
The
❏ Memory Blocks
❏ PLD Blocks
❏ Bus Interface
PSD835G2
Functional
Blocks
❏ I/O Ports
❏ Power Management Unit
❏ JTAG-ISP Interface
The functions of each block are described in the following sections. Many of the blocks
perform multiple functions, and are user configurable.
9.1 Memory Blocks
The PSD835G2 has the following memory blocks:
• The main Flash memory
• Secondary Flash memory
• SRAM.
The memory select signals for these blocks originate from the Decode PLD (DPLD) and
are user-defined in PSDsoft.
Table 7 summarizes which versions of the PSD835G2 contain which memory blocks.
Table 7. Memory Blocks
Main Flash
Secondary Flash
Device
Flash Size
512KB
Sector Size
Block Size
32KB
Sector Size
SRAM
PSD835G2
64KB
8KB
8KB
9.1.1 Main Flash and Secondary Flash Memory Description
The main Flash memory block is divided evenly into eight sectors. The secondary Flash
memory is divided into four sectors of eight Kbytes each. Each sector of either memory
can be separately protected from program and erase operations.
Flash memory may be erased on a sector-by-sector basis and programmed word-by-word.
Flash sector erasure may be suspended while data is read from other sectors of memory
and then resumed after reading.
During a program or erase of Flash, the status can be output on the Rdy/Bsy pin of Port
PE4. This pin is set up using PSDsoft.
9.1.1.1 Memory Block Selects
The decode PLD in the PSD835G2 generates the chip selects for all the internal memory
blocks (refer to the PLD section). Each of the eight Flash memory sectors have a
Flash Select signal (FS0-FS7) which can contain up to three product terms. Each of the
four Secondary Flash memory sectors have a Select signal (CSBOOT0-3) which can
contain up to three product terms. Having three product terms for each sector select signal
allows a given sector to be mapped in different areas of system memory. When using a
microcontroller (80C51) with separate Program and Data space, these flexible select
signals allow dynamic re-mapping of sectors from one space to the other before and after
IAP.
16
PSD835G2
PSD8XX Family
9.1.1.2 Upper and Lower Block IN MAIN FLASH SECTOR
The
The PSD835G2’s main Flash has eight 64K bytes sector. The 64K byte sector size may
cause some difficulty in code mapping for an 8-bit MCU with only 64K byte address space.
To resolve this mapping issue, the PSD835G2 provides additional logic (Figure 3) for the
user to split the 8 sectors such that each sector has a lower and upper 32K byte block, and
the two blocks can reside in different pages but in the same address range.
PSD835G2
Functional
Blocks
(cont.)
If your design works with 64KB sectors, you don’t need to configure this logic. If the design
requires 32KB blocks in each sector, you need to define a “FA15” PLD equation in
PSDsoft as the A15 address input to the main Flash module. FA15 consists of 3 product
terms and will control whether the MCU is accessing the lower or upper 32KB in the
selected sector. Below is an example for Flash sector chip select FS0. A typical equation
is FA15 = pgr4 of the Page Register. When pgr4 is 0 (page 00), the lower 32KB is
selected. When pgr4 is switched to 1 by the user, the upper 32KB is selected. PSDsoft will
automatically generate the PLD equations shown, based on your point and click
selections.
page = [pgr7...pgr0]; “Page Register output
“Sector Chip Select Equation
FS0 = ((0000h <= address <= 7FFFh) & page = 00h) # “select first 32KB block
((0000h <= address <= 7FFFh) & page = 10h);
“select second 32KB block
FA15 = pgr4; “as address A15 input to the main Flash
If no FA15 equation is defined in PSDsoft, the A15 that comes from the MCU address bus
will be routed as input to the main Flash instead of FA15. The FA15 equation has no
impact in the Sector Erase operation. Note: FA15 affects all eight sectors of the main Flash
simultaneously, you cannot direct FA15 to a particular Flash sector only.
9.1.1.3 The Ready/Busy Pin (PE4)
Pin PE4 can be used to output the Ready/Busy status of the PSD835G2. The output on
the pin will be a ‘0’ (Busy) when Flash memory blocks are being written to, or when the
Flash memory block is being erased. The output will be a ‘1’ (Ready) when no write or
erase operation is in progress.
Figure 3. Selecting the Upper or Lower Block in a Main Flash Sector
FLASH CHIP SELECTS FS0-7
DPLD
ARRAY
FA15
MAIN
FLASH
SECTOR
ADDR A15
MUX
A15
NVM CONTROL BIT*
A [14:0]
* Set by PSDsoft
17
PSD8XX Family
PSD835G2
9.1.1.4 Memory Operation
The
The main Flash and secondary Flash memories are addressed through the microcontroller
interface on the PSD835G2 device. The microcontroller can access these memories in one
of two ways:
PSD835G2
Functional
Blocks
(cont.)
❏ The microcontroller can execute a typical bus write or read operation just as it would
if accessing a RAM or ROM device using standard bus cycles.
❏ The microcontroller can execute a specific instruction that consists of several write
and read operations. This involves writing specific data patterns to special addresses
within the Flash to invoke an embedded algorithm. These instructions are summarized
in Table 8.
Typically, Flash memory can be read by the microcontroller using read operations, just
as it would read a ROM device. However, Flash memory can only be erased and
programmed with specific instructions. For example, the microcontroller cannot write a
single byte directly to Flash memory as one would write a byte to RAM. To program a byte
into Flash memory, the microcontroller must execute a program instruction sequence, then
test the status of the programming event. This status test is achieved by a read
operation or polling the Rdy/Busy pin (PE4).
The Flash memory can also be read by using special instructions to retrieve particular
Flash device information (sector protect status and ID).
9.1.1.4.1 Instructions
An instruction is defined as a sequence of specific operations. Each received byte is
sequentially decoded by the PSD and not executed as a standard write operation. The
instruction is executed when the correct number of bytes are properly received and the
time between two consecutive bytes is shorter than the time-out value. Some instructions
are structured to include read operations after the initial write operations.
The sequencing of any instruction must be followed exactly. Any invalid combination of
instruction bytes or time-out between two consecutive bytes while addressing Flash
memory will reset the device logic into a read array mode (Flash memory reads like a
ROM device).
The PSD835G2 main Flash and secondary Flash support these instructions (see Table 8):
❏ Erase memory by chip or sector
❏ Suspend or resume sector erase
❏ Program a byte
❏ Reset to read array mode
❏ Read Main Flash Identifier value
❏ Read sector protection status
❏ Bypass Instruction
These instructions are detailed in Table 8. For efficient decoding of the instructions, the
first two bytes of an instruction are the coded cycles and are followed by a command byte
or confirmation byte. The coded cycles consist of writing the data AAh to address X555h
during the first cycle and data 55h to address XAAAh during the second cycle (unless the
Bypass Instruction feature is used. See 9.1.1.7). Address lines A15-A12 are don’t care
during the instruction write cycles. However, the appropriate sector select signal (FSi or
CSBOOTi) must be selected.
The main Flash and the secondary Flash Block have the same set of instructions (except
Read main Flash ID). The chip selects of the Flash memory will determine which Flash will
receive and execute the instruction. The main Flash is selected if any one of the FS0-7 is
active, and the secondary Flash Block is selected if any one of the CSBOOT0-3 is active.
18
PSD835G2
PSD8XX Family
The
Table 8. Instructions
PSD835G2
Functional
Blocks
(cont.)
FS0-7
or
Instruction
CSBOOT0-3 Cycle 1 Cycle 2 Cycle 3 Cycle 4
Cycle5
Cycle 6 Cycle 7
Read (Note 5)
1
1
“Read”
RA RD
Read Main Flash ID
(Notes 6,13)
AAh
@555h
55h
90h
“Read”
ID
@AAAh @555h
@x01h
Read Sector Protection
(Notes 6,8,13)
1
AAh
@555h
55h
90h
“Read”
@AAAh @555h 00h or 01h
@x02h
Program a Flash Byte
1
1
AAh
@555h
55h
A0h
PD@PA
@AAAh @555h
Erase One Flash Sector
AAh
55h 80h
AAh
55h
30h
30h
@555h
@AAAh @555h
@555h
@AAAh
@SA
@next SA
(Note 7)
Erase Flash Block
(Bulk Erase)
1
1
1
1
1
1
1
AAh
@555h
55h
80h
AAh
@555h
55h
@AAAh
10h
@555h
@AAAh @555h
Suspend Sector Erase
(Note 11)
B0h
@xxxh
Resume Sector Erase
(Note 12)
30h
@xxxh
Reset (Note 6)
F0 @ any
address
Unlock Bypass
AAh
@555h
55h
20h
@AAAh @555h
Unlock Bypass Program
(Note 9)
A0h
@xxxh
PD@PA
Unlock Bypass Reset
(Note 10)
90h
@xxxh
00h
@xxxh
X
= Don’t Care.
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of the WR#
(CNTL0) pulse.
PD = Data to be programmed at location PA. Data is latched o the rising edge of WR# (CNTL0) pulse.
SA = Address of the sector to be erased or verified. The chip select (FS0-7 or CSBOOT0-3) of the sector to be
erased must be active (high).
NOTES:
1. All bus cycles are write bus cycle except the ones with the “read” label.
2. All values are in hexadecimal.
3. FS0-7 and CSBOOT0-3 are active high and are defined in PSDsoft.
4. Only Address bits A11-A0 are used in Instruction decoding. A15-12 (or A16-A12) are don’t care.
5. No unlock or command cycles required when device is in read mode.
6. The Reset command is required to return to the read mode after reading the Flash ID, Sector Protect status
or if DQ5 (error flag) goes high.
7. Additional sectors to be erased must be entered within 80µs.
8. The data is 00h for an unprotected sector and 01h for a protected sector. In the fourth cycle, the sector chip
select is active and (A1 = 1, A0 = 0).
9. The Unlock Bypass command is required prior to the Unlock Bypass Program command.
10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the
Unlock Bypass mode.
11. The system may read and program functions in non-erasing sectors, read the Flash ID or read the Sector
Protect status, when in the Erase Suspend mode. The erase Suspend command is valid only during a sector
erase operation.
12. The Erase Resume command is valid only during the Erase Suspend mode.
13. The MCU cannot invoke these instructions while executing code from the same Flash memory for which the
instruction is intended. The MCU must fetch, for example, codes from the secondary block when reading the
Sector Protection Status of the main Flash.
19
PSD8XX Family
PSD835G2
The
9.1.1.5 Power-Up Condition
The PSD835G2 internal logic is reset upon power-up to the read array mode. The FSi and
CSBOOTi select signals, along with the write strobe signal, must be in the false state
during power-up for maximum security of the data contents and to remove the possibility of
data being written on the first edge of a write strobe signal. Any write cycle initiation is
PSD835G2
Functional
Blocks
(cont.)
locked when V is below VLKO.
CC
9.1.1.6 Read
Under typical conditions, the microcontroller may read the Flash, or secondary Flash
memories using read operations just as it would a ROM or RAM device. Alternately, the
microcontoller may use read operations to obtain status information about a program or
erase operation in progress. Lastly, the microcontroller may use instructions to read
special data from these memories. The following sections describe these read functions.
9.1.1.6.1 Read the Contents of Memory
Main Flash and secodary Flash memories are placed in the read array mode after
power-up, chip reset, or a Reset Flash instruction (see Table 8). The microcontroller can
read the memory contents of main Flash or secondary Flash by using read operations any
time the read operation is not part of an instruction sequence.
9.1.1.6.2 Read the Main Flash Memory Identifier
The main Flash memory identifier is read with an instruction composed of 4 operations:
3 specific write operations and a read operation (see Table 8). The PSD835G2 main Flash
memory ID is E8h.
9.1.1.6.3 Read the Flash Memory Sector Protection Status
The Flash memory sector protection status is read with an instruction composed of 4
operations: 3 specific write operations and a read operation (see Table 8). The read
operation will produce 01h if the Flash sector is protected, or 00h if the sector is not
protected.
The sector protection status for all NVM blocks (main Flash or secondary Flash) can also
be read by the microcontroller accessing the Flash Protection and Flash Boot Protection
registers in PSD I/O space. See section 9.1.1.9.1 for register definitions.
9.1.1.6.4 Read the Erase/Program Status Bits
The PSD835G2 provides several status bits to be used by the microcontroller to confirm
the completion of an erase or programming instruction of Flash memory. These status bits
minimize the time that the microcontroller spends performing these tasks and are defined
in Table 9. The status bits can be read as many times as needed.
Table 9. Status Bits
FSi/
CSBOOTi
DQ7
Data Toggle Error
Polling Flag Flag
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
Erase
Time-
out
Flash
V
X
X
X
X
IH
NOTES: 1. X = Not guaranteed value, can be read either 1 or 0.
2. DQ7-DQ0 represent the Data Bus bits, D7-D0.
3. FSi/CSBOOTi are active high.
For Flash memory, the microcontroller can perform a read operation to obtain these status
bits while an erase or program instruction is being executed by the embedded algorithm.
See section 9.1.1.7 for details.
20
PSD835G2
PSD8XX Family
9.1.1.6.5 Data Polling Flag DQ7
The
When Erasing or Programming the Flash memory bit DQ7 outputs the complement of the
bit being entered for Programming/Writing on DQ7. Once the Program instruction or the
Write operation is completed, the true logic value is read on DQ7 (in a Read operation).
Flash memory specific features:
PSD835G2
Functional
Blocks
(cont.)
❏ Data Polling is effective after the fourth Write pulse (for programming) or after the
sixth Write pulse (for Erase). It must be performed at the address being programmed
or at an address within the Flash sector being erased.
❏ During an Erase instruction, DQ7 outputs a ‘0’. After completion of the instruction,
DQ7 will output the last bit programmed (it is a ‘1’ after erasing).
❏ If the location to be programmed is in a protected Flash sector, the instruction is
ignored.
❏ If all the Flash sectors to be erased are protected, DQ7 will be set to ‘0’ for
about 100 µs, and then return to the previous addressed location. No erasure will be
performed.
9.1.1.6.6 Toggle Flag DQ6
The PSD835G2 offers another way for determining when the Flash memory Program
instruction is completed. During the internal Write operation and when either the FSi or
CSBOOTi is true, the DQ6 will toggle from ‘0’ to ‘1’ and ‘1’ to ‘0’ on subsequent attempts to
read any byte of the memory.
When the internal cycle is complete, the toggling will stop and the data read on the
Data Bus D0-7 is the addressed memory location. The device is now accessible for a new
Read or Write operation. The operation is finished when two successive reads yield the
same output data. Flash memory specific features:
❏ The Toggle bit is effective after the fourth Write pulse (for programming) or after the
sixth Write pulse (for Erase).
❏ If the location to be programmed belongs to a protected Flash sector, the instruction
is ignored.
❏ If all the Flash sectors selected for erasure are protected, DQ6 will toggle to ‘0’ for
about 100 µs and then return to the previous addressed location.
9.1.1.6.7 Error Flag DQ5
During a correct Program or Erase, the Error bit will set to ‘0’. This bit is set to ‘1’ when
there is a failure during Flash programming, Sector erase, or Bulk Erase.
In the case of Flash programming, the Error Bit indicates the attempt to program a Flash
bit(s) from the programmed state (0) to the erased state (1), which is not a valid operation.
The Error bit may also indicate a timeout condition while attempting to program a byte.
In case of an error in Flash sector erase or byte program, the Flash sector in which the
error occurred or to which the programmed location belongs must no longer be used.
Other Flash sectors may still be used. The Error bit resets after the Reset instruction.
9.1.1.6.8 Erase Time-out Flag DQ3
The Erase Timer bit reflects the time-out period allowed between two consecutive Sector
Erase instructions. The Erase timer bit is set to ‘0’ after a Sector Erase instruction for a
time period of 100 µs + 20% unless an additional Sector Erase instruction is decoded.
After this time period or when the additional Sector Erase instruction is decoded, DQ3 is
set to ‘1’.
21
PSD8XX Family
PSD835G2
The
9.1.1.7 Programming Flash Memory
Flash memory must be erased prior to being programmed. The MCU may erase Flash
memory all at once or by-sector. Flash memory sector erases to all logic ones (FF hex),
and its bits are programmed to logic zeros. Although erasing Flash memory occurs on a
sector basis, programming Flash memory occurs on a word basis.
PSD835G2
Functional
Blocks
(cont.)
The PSD835G2 main Flash and secondary Flash memories require the MCU to send an
instruction to program a word or perform an erase function (see Table 8).
Once the MCU issues a Flash memory program or erase instruction, it must check for the
status of completion. The embedded algorithms that are invoked inside the PSD835G2
support several means to provide status to the MCU. Status may be checked using any of
three methods: Data Polling, Data Toggle, or the Ready/Busy output pin.
9.1.1.7.1 Data Polling
Polling on DQ7 is a method of checking whether a Program or Erase instruction is in
progress or has completed. Figure 4 shows the Data Polling algorithm.
When the MCU issues a programming instruction, the embedded algorithm within the
PSD835G2 begins. The MCU then reads the location of the word to be programmed in
Flash to check status. Data bit DQ7 of this location becomes the compliment of data
bit 7of the original data word to be programmed. The MCU continues to poll this location,
comparing DQ7 and monitoring the Error bit on DQ5. When the DQ7 matches data bit 7 of
the original data, and the Error bit at DQ5 remains ‘0’, then the embedded algorithm is
complete. If the Error bit at DQ5 is ‘1’, the MCU should test DQ7 again since DQ7 may
have changed simultaneously with DQ5 (see Figure 4).
The Error bit at DQ5 will be set if either an internal timeout occurred while the embedded
algorithm attempted to program the location or if the MCU attempted to program a ‘1’ to a
bit that was not erased (not erased is logic ‘0’).
It is suggested (as with all Flash memories) to read the location again after the embedded
programming algorithm has completed to compare the word that was written to Flash with
the word that was intended to be written.
When using the Data Polling method after an erase instruction, Figure 4 still applies.
However, DQ7 will be ‘0’ until the erase operation is complete. A ‘1’ on DQ5 will indicate
a timeout failure of the erase operation, a ‘0’ indicates no error. The MCU can read any
location within the sector being erased to get DQ7 and DQ5.
PSDsoft generates ANSI C code functions which implement these Data Polling
algorithms.
22
PSD835G2
PSD8XX Family
The
Figure 4. Data Polling Flow Chart
PSD835G2
Functional
Blocks
(cont.)
START
READ DQ5 & DQ7
at VALID ADDRESS
DQ7
=
DATA7
YES
NO
NO
DQ5
=1
YES
READ DQ7
YES
DQ7
=
DATA
NO
FAIL
PASS
Program/Erase
Operation Failed
Issue Reset Instruction
Program/Erase
Operation is
Completed
9.1.1.7.2 Data Toggle
Checking the Data Toggle bit on DQ6 is a method of determining whether a Program or
Erase instruction is in progress or has completed. Figure 5 shows the Data Toggle
algorithm.
When the MCU issues a programming instruction, the embedded algorithm within the
PSD835G2 begins. The MCU then reads the location to be programmed in Flash to check
status. Data bit DQ6 of this location will toggle each time the MCU reads this location until
the embedded algorithm is complete. The MCU continues to read this location, checking
DQ6 and monitoring the Error bit on DQ5. When DQ6 stops toggling (two consecutive
reads yield the same value), and the Error bit on DQ5 remains ‘0’, then the embedded
algorithm is complete. If the Error bit on DQ5 is ‘1’, the MCU should test DQ6 again, since
DQ6 may have changed simultaneously with DQ5 (see Figure 5).
The Error bit at DQ5 will be set if either an internal timeout occurred while the embedded
algorithm attempted to program, or if the MCU attempted to program a ‘1’ to a bit that was
not erased (not erased is logic ‘0’).
23
PSD8XX Family
PSD835G2
9.1.1.7.2 Data Toggle (cont.)
The
It is suggested (as with all Flash memories) to read the location again after the embedded
programming algorithm has completed to compare the word that was written to Flash with
the word that was intended to be written.
PSD835G2
Functional
Blocks
(cont.)
When using the Data Toggle method after an erase instructin, Figure 5 still applies. DQ6
will toggle until the erase operation is complete. A ‘1’ on DQ5 will indicate a timeout failure
of the erase operation, a ‘0’ indicates no error. The MCU can read any even location within
the sector being erased to get DQ6 and DQ5.
PSDsoft generates ANSI C code functions which implement these Data Toggling
algorithms.
Figure 5. Data Toggle Flow Chart
START
READ
DQ5 & DQ6
DQ6
NO
=
TOGGLE
YES
NO
DQ5
=1
YES
READ DQ6
DQ6
=
TOGGLE
NO
YES
FAIL
PASS
Program/Erase
Operation Failed
Issue Reset Instruction
Program/Erase
Operation is
Completed
24
PSD835G2
PSD8XX Family
The
9.1.1.8 Unlock Bypass Instruction
The unlock bypass feature allows the system to program words to the flash memories
faster than using the standard program instruction. The unlock bypass instruction is
initiated by first writing two unlock cycles. This is followed by a third write cycle containing
the unlock bypass command, 20h (see Table 8). The flash memory then enters the unlock
bypass mode. A two-cycle Unlock Bypass Program instruction is all that is required to
program in this mode. The first cycle in this instruction contains the unlock bypass
programm command, A0h; the second cycle contains the program address and data.
Additional data is programmed in the same manner. This mode dispenses with the initial
two unlock cycles required in the standard program instruction, resulting in faster total
programming time. During the unlock bypass mode, only the Unlock Bypass Program and
Unlock Bypass Reset instructions are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset instruction. The first cycle must contain the
data 90h; the second cycle the data 00h. Addresses are don’t care for both cycles. The
Flash memory then returns to reading array data mode.
PSD835G2
Functional
Blocks
(cont.)
9.1.1.9 Erasing Flash Memory
9.1.1.9.1. Flash Bulk Erase Instruction
The Flash Bulk Erase instruction uses six write operations followed by a Read operation of
the status register, as described in Table 8. If any byte of the Bulk Erase instruction is
wrong, the Bulk Erase instruction aborts and the device is reset to the Read Flash memory
status.
During a Bulk Erase, the memory status may be checked by reading status bits DQ5, DQ6,
and DQ7, as detailed in section 9.1.1.7. The Error bit (DQ5) returns a ‘1’ if there has been
an Erase Failure (maximum number of erase cycles have been executed).
It is not necessary to program the array with 00h because the PSD835G2 will automatically
do this before erasing to 0FFh.
During execution of the Bulk Erase instruction, the Flash memory will not accept any
instructions.
9.1.1.9.2 Flash Sector Erase Instruction
The Sector Erase instruction uses six write operations, as described in Table 8. Additional
Flash Sector Erase confirm commands and Flash sector addresses can be written
subsequently to erase other Flash sectors in parallel, without further coded cycles, if the
additional instruction is transmitted in a shorter time than the timeout period of about
100 µs. The input of a new Sector Erase instruction will restart the time-out period.
The status of the internal timer can be monitored through the level of DQ3 (Erase time-out
bit). If DQ3 is ‘0’, the Sector Erase instruction has been received and the timeout is
counting. If DQ3 is ‘1’, the timeout has expired and the PSD835G2 is busy erasing the
Flash sector(s). Before and during Erase timeout, any instruction other than Erase suspend
and Erase Resume will abort the instruction and reset the device to Read Array mode.
It is not necessary to program the Flash sector with 00h as the PSD835G2 will do this
automatically before erasing.
During a Sector Erase, the memory status may be checked by reading status bits DQ5,
DQ6, and DQ7, as detailed in section 9.1.1.7.
During execution of the erase instruction, the Flash block logic accepts only Reset and
Erase Suspend instructions. Erasure of one Flash sector may be suspended, in order to
read data from another Flash sector, and then resumed.
25
PSD8XX Family
PSD835G2
9.1.1.9.3 Flash Erase Suspend Instruction
The
When a Flash Sector Erase operation is in progress, the Erase Suspend instruction will
suspend the operation by writing 0B0h to any even address when an appropriate Chip
Select (FSi or CSBOOTi) is true. (See Table 8). This allows reading of data from another
Flash sector after the Erase operation has been suspended. Erase suspend is accepted
only during the Flash Sector Erase instruction execution and defaults to read array
mode. An Erase Suspend instruction executed during an Erase timeout will, in addition to
suspending the erase, terminate the time out.
PSD835G2
Functional
Blocks
(cont.)
The Toggle Bit DQ6 stops toggling when the PSD835G2 internal logic is suspended. The
toggle Bit status must be monitored at an address within the Flash sector being erased.
The Toggle Bit will stop toggling between 0.1 µs and 15 µs after the Erase Suspend
instruction has been executed. The PSD835G2 will then automatically be set to Read
Flash Block Memory Array mode.
If an Erase Suspend instruction was executed, the following rules apply:
• Attempting to read from a Flash sector that was being erased will output invalid data.
• Reading from a Flash sector that was not being erased is valid.
• The Flash memory cannot be programmed, and will only respond to Erase Resume
and Reset instructions (read is an operation and is OK).
• If a Reset instruction is received, data in the Flash sector that was being erased will
be invalid.
9.1.1.9.4 Flash Erase Resume Instruction
If an Erase Suspend instruction was previously executed, the erase operation may be
resumed by this instruction. The Erase Resume instruction consists of writing 030h to any
even address while an appropriate Chip Select (FSi or CSBOOTi) is true. (See Table 8.)
9.1.1.10 Specific Features
9.1.1.10.1 Main Flash and Secondary Flash Sector Protect
Each sector of main Flash and secondary Flash memory can be separately protected
against Program and Erase functions. Sector Protection provides additional data
security because it disables all program or erase operations. This mode can be activated
(or deactivated) through the JTAG-ISP Port or a Device Programmer.
Sector protection can be selected for each sector using the PSDsoft program. This will
automatically protect selected sectors when the device is programmed through the JTAG
Port or a Device Programmer. Flash sectors can be unprotected to allow updating of their
contents using the JTAG Port or a Device Programmer. The microcontroller can read (but
cannot change) the sector protection bits.
Any attempt to program or erase a protected Flash sector will be ignored by the device.
The Verify operation will result in a read of the protected data. This allows a guarantee of
the retention of the Protection status.
The sector protection status can either be read by the MCU through the Flash protection
and secondary Flash protection registers (CSIOP) or use the read sector protection
instruction (Table 8).
26
PSD835G2
PSD8XX Family
The
Table 10. Sector Protection/Security Bit Definition
Flash Protection Register
PSD835G2
Functional
Blocks
(cont.)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Sec7_Prot Sec6_Prot Sec5_Prot Sec4_Prot Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
Bit Definitions:
Sec<i>_Prot
Sec<i>_Prot
1 = Main Flash Sector <i> is write protected.
0 = Main Flash Sector <i> is not write protected.
Flash Boot Protection Register
Bit 7
Bit 6
Bit 5
Bit 4
*
Bit 3
Bit 2
Bit 1
Bit 0
Security_
Bit
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
*
*
*: Not used.
Bit Definitions:
Sec<i>_Prot
Sec<i>_Prot
1 = Flash Boot Sector <i> is write protected.
0 = Flash Boot Sector <i> is not write protected.
Security_Bit
0 = Security Bit in device has not been set.
1 = Security Bit in device has been set.
9.1.1.10.2 Reset Instruction
The Reset instruction consists of one write cycle (see Table 8). It can also be optionally
preceded by the standard two write decoding cycles (writing AAh to AAAh and 55h to
554h).
The Reset instruction must be executed after:
1. Reading the Flash Protection status or Flash ID using the Flash instruction.
2. When an error condition occurs (DQ5 goes high) during a Flash programming or erase
cycle.
The Reset instruction will reset the Flash to normal Read Mode immediately. However, if
there is an error condition (DQ5 goes high), the Flash memory will return to the Read
Mode in 25 µSeconds after the Reset instruction is issued.
The Reset instruction is ignored when it is issued during a Flash programming or Bulk
Erase cycle. The Reset instruction will abort the on going sector erase cycle and return the
Flash memory to normal Read Mode in 25 µSeconds.
9.1.1.10.3 Reset Pin Input
The reset pulse input from the pin will abort any operation in progress and reset the Flash
memory to Read Mode. When the reset occurs during a programming or erase cycle, the
Flash memory will take up to 25 µSeconds to return to Read Mode. It is recommended that
the reset pulse (except power on reset, see Reset Section) be at least 25 µSeconds such
that the Flash memory will always be ready for the MCU to fetch the boot code after reset
is over.
27
PSD8XX Family
PSD835G2
The
9.1.2 SRAM
The SRAM is enabled when RS0—the SRAM chip select output from the DPLD—is high.
RS0 can contain up to three product terms, allowing flexible memory mapping.
PSD835G2
Functional
Blocks
(cont.)
The SRAM can be backed up using an external battery. The external battery should be
connected to the Vstby pin (PE6). If you have an external battery connected to the
PSD835G2, the contents of the SRAM will be retained in the event of a power loss. The
contents of the SRAM will be retained so long as the battery voltage remains at 2V or
greater. If the supply voltage falls below the battery voltage, an internal power switchover
to the battery occurs.
Pin PE7 can be configured as an output that indicates when power is being drawn from the
external battery. This Vbaton signal will be high with the supply voltage falls below the bat-
tery voltage and the battery on PE6 is supplying power to the internal SRAM.
The chip select signal (RS0) for the SRAM, Vstby, and Vbaton are all configured using
PSDsoft.
9.1.3 Memory Select Signals
The main Flash (FSi), secondary Flash (CSBOOTi), and SRAM (RS0) memory select
signals are all outputs of the DPLD. They are defined using PSDsoft. The following rules
apply to the equations for the internal chip select signals:
1. Main Flash memory and secondary Flash memory sector select signals must not be
larger than the physical sector size.
2. Any main Flash memory sector must not be mapped in the same memory space as
another Main Flash sector.
3. A secondary Flash memory sector must not be mapped in the same memory space as
another Flash Boot sector.
4. SRAM and I/O spaces must not overlap.
5. A secondary Flash memory sector may overlap a main Flash memory sector. In case of
overlap, priority will be given to the Flash Boot sector.
6. SRAM and I/O spaces may overlap any other memory sector. Priority will be given to
the SRAM and I/O.
Example
FS0 is valid when the address is in the range of 8000h to BFFFh, CSBOOT0 is valid from
8000h to 9FFFh, and RS0 is valid from 8000h to 87FFh. Any address in the range of RS0
will always access the SRAM. Any address in the range of CSBOOT0 greater than 87FFh
(and less than 9FFFh) will automatically address Boot memory segment 0. Any address
greater than 9FFFh will access the Flash memory segment 0. You can see that half of the
Flash memory segment 0 and one-fourth of Boot segment 0 can not be accessed in this
example. Also note that an equation that defined FS1 to anywhere in the range of 8000h to
BFFFh would not be valid.
Figure 6 shows the priority levels for all memory components. Any component on a higher
level can overlap and has priority over any component on a lower level. Components on
the same level must not overlap. Level one has the highest priority and level 3 has the
lowest.
28
PSD835G2
PSD8XX Family
The
Figure 6. Priority Level of Memory and I/O Components
PSD835G2
Functional
Blocks
(cont.)
Highest Priority
Level 1
SRAM, I/O, or
Peripheral I/O
Level 2
Secondary Flash Memory
Level 3
Main Flash Memory
Lowest Priority
9.1.3.1. Memory Select Configuration for MCUs with Separate Program and Data Spaces
The 80C51 and compatible family of microcontrollers, can be configured to have separate
address spaces for code memory (selected using PSEN) and data memory (selected using
RD). Any of the memories within the PSD835G2 can reside in either space or both spaces.
This is controlled through manipulation of the VM register that resides in the PSD’s CSIOP
space.
The VM register is set using PSDsoft to have an initial value. It can subsequently be
changed by the microcontroller so that memory mapping can be changed on-the-fly.
For example, you may wish to have SRAM and main Flash in Data Space at boot, and
secondary Flash memory in Program Space at boot, and later swap main and secondary
Flash memory. This is easily done with the VM register by using PSDsoft to configure it for
boot up and having the microcontroller change it when desired.
Table 11 describes the VM Register.
Table 11. VM Register
Bit 7
Bit 6* Bit 5* Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PIO_EN
FL_Data Boot_Data FL_Code Boot_Code SRAM_Code
0 = disable
PIO mode
0 = RD 0 = RD
can’t can’t
access access
Flash
0 = PSEN 0 = PSEN
0 = PSEN
can’t
access
*
*
*
*
can’t
can’t
access
access
Boot Flash Flash
Boot Flash SRAM
1 = PSEN 1 = PSEN 1 = PSEN
access access access
Boot Flash Flash Boot Flash SRAM
1= enable
PIO mode
1 = RD 1 = RD
access access
Flash
NOTE: Bits 6-5 are not used.
29
PSD8XX Family
PSD835G2
9.1.3.2 Configuration Modes for MCUs with Separate Program and Data Spaces
9.1.3.2.1 Separate Space Modes
The
PSD835G2
Functional
Blocks
(cont.)
Code memory space is separated from data memory space. For example, the PSEN
signal is used to access the program code from the main Flash Memory, while the RD
signal is used to access data from the secondary Flash memory, SRAM and I/O Ports.
This configuration requires the VM register to be set to 0Ch.
9.1.3.2.2 . Combined Space Modes
The program and data memory spaces are combined into one space that allows the main
Flash Memory, secondary Flash memory, and SRAM to be accessed by either PSEN or
RD. For example, to configure the main Flash memory in combined space mode, bits 2
and 4 of the VM register are set to “1”.
9.1.3.3 80C51XA Memory Map Example
See Application Notes for examples.
Figure 7. 80C51 Memory Modes – Separate Space Mode
MAIN
FLASH
FLASH
BOOT
SRAM
DPLD
RS0
BLOCK
CSBOOT0-3
FS0-7
CS
CS
CS
OE
OE
OE
PSEN
RD
Figure 8. 80C51 Memory Mode – Combined Space Mode
MAIN
FLASH
FLASH
BOOT
SRAM
DPLD
RS0
BLOCK
RD
CSBOOT0-3
FS0-7
CS
CS
CS
OE
OE
OE
VM REG BIT 3
VM REG BIT 4
PSEN
VM REG BIT 1
RD
VM REG BIT 2
VM REG BIT 0
30
PSD835G2
PSD8XX Family
The
9.1.4 Page Register
The eight bit Page Register increases the addressing capability of the microcontroller by a
factor of up to 256. The contents of the register can also be read by the microcontroller.
The outputs of the Page Register (PGR0-PGR7) are inputs to the PLD decoder and
can be included in the Flash Memory, secondary Flash memory, and SRAM chip select
equations.
PSD835G2
Functional
Blocks
(cont.)
If memory paging is not needed, or if not all 8 page register bits are needed for memory
paging, then these bits may be used in the PLD for general logic. See Application
Notes.
Figure 9 shows the Page Register. The eight flip flops in the register are connected to the
internal data bus D0-D7. The microcontroller can write to or read from the Page Register.
The Page Register can be accessed at address location CSIOP + E0h.
Figure 9. Page Register
RESET
PGR0
INTERNAL
SELECTS
AND LOGIC
D0
D1
D2
D3
D4
D5
D6
D7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
PGR1
PGR2
PGR3
PGR4
PGR5
PGR6
PGR7
D0 - D7
DPLD
AND
GPLD
R/W
PAGE
REGISTER
FLASH
PLD
31
PSD8XX Family
PSD835G2
The
9.1.5 Memory ID Registers
The 8-bit read only memory status registers are included in the CSIOP space. The user
can determine the memory configuration of the PSD device by reading the Memory ID0
and Memory ID1 registers. The content of the registers are defined as follow:
PSD835G2
Functional
Blocks
(cont.)
Memory_ID0 Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
S_size 3
S_size 2
S_size 1
S_size 0
F_size 3
F_size 2
F_size 1
F_size 0
Bit Definition
F_size3
Main Flash Size
(Bit)
F_size2
F_size1
F_size0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
none
256K
512K
1M
2M
4M
8M
SRAM Size
(Bit)
S_size3
S_size2
S_size1
S_size0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
none
16K
32K
64K
Memory_ID1 Register
Bit 7
*
Bit 6
*
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
B_type 1
B_type 0
B_size 3
B_size 2
B_size 1
B_size 0
*Not used bit should be set to zero.
Bit Definition
Boot Block Size
(Bit)
B_size3
B_size2
B_size1
B_size0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
none
128K
256K
512K
B_type1
B_type0
Boot Block Type
0
0
0
1
Flash
EEPROM
32
PSD835G2
PSD8XX Family
The
9.2 PLDs
The PLDs bring programmable logic functionality to the PSD835G2. After specifying the
logic for the PLDs in PSDsoft, the logic is programmed into the device and available upon
power-up.
PSD835G2
Functional
Blocks
(cont.)
The PSD835G2 contains two PLDs: the Decode PLD (DPLD), and the Complex PLD
(CPLD). The PLDs are briefly discussed in the next few paragraphs, and in more detail in
sections 9.2.1 and 9.2.2. Figure 10 shows the configuration of the PLDs.
The DPLD performs address decoding for internal components, such as memory,
registers, and I/O port selects.
The CPLD can be used for logic functions, such as loadable counters and shift registers,
state machines, and encoding and decoding logic. These logic functions can be
constructed using the 16 Output Micro Cells (OMCs), 24 Input Micro Cells (IMCs), and
the AND array. The CPLD can also be used to generate external chip selects.
The AND array is used to form product terms. These product terms are specified using
PSDsoft. An Input Bus consisting of 82 signals is connected to the PLDs. The signals are
shown in Table 12.
Table 12. DPLD and CPLD Inputs
Input Source
Input Name
Number
of Signals
MCU Address Bus
A[15:0]*
16
3
1
1
8
8
8
4
8
8
8
8
1
MCU Control Signals
Reset
CNTL[2:0]
RST
Power Down
PDN
Port A Input Micro Cells
Port B Input Micro Cells
Port C Input Micro Cells
Port D Inputs
PA[7-0]
PB[7-0]
PC[7-0]
PD[3:0]
Port F Inputs
PF[7:0]
Page Register
PGR(7:0)
MCELLA.FB[7:0]
MCELLB.FB[7:0]
Rdy/Bsy
Micro Cell A Feedback
Micro Cell B Feedback
Flash Programming Status Bit
NOTE: The address inputs are A[19:4] in 80C51XA mode.
The Turbo Bit
The PLDs in the PSD835G2 can minimize power consumption by switching to standby
when inputs remain unchanged for an extended time of about 70 ns. Setting the Turbo
mode bit to off (Bit 3 of the PMMR0 register) automatically places the PLDs into standby if
no inputs are changing. Turbo-off mode increases propagation delays while reducing
power consumption. Refer to the Power Management Unit section on how to set the Turbo
Bit. Additionally, five bits are available in the PMMR2 register to block MCU control signals
from entering the PLDs. This reduces power consumption and can be used only when
these MCU control signals are not used in PLD logic equations.
33
8
PAGE
REGISTER
DATA
BUS
8
FLASH MEMORY SELECTS
DECODE PLD
82
4
1
1
2
1
FLASH BOOT MEMORY SELECTS
SRAM SELECT
CSIOP SELECT
PERIPHERAL I/O MODE SELECTS
JTAG SELECT
DIRECT MICRO CELL ACCESS FROM MCU DATA BUS
OUTPUT MICRO CELL FEEDBACK
16
MCELLA
TO PORT A
CPLD
16 OUTPUT
MICRO CELL
8
PT
ALLOC.
MCELLB
TO PORT B
82
8
8
24 INPUT MICRO CELL
(PORT A,B,C)
EXTERNAL CHIP SELECTS
TO PORT C OR F
DIRECT MICRO CELL INPUT TO MCU DATA BUS
INPUT MICRO CELL & INPUT PORTS
PORT D AND F INPUTS
24
12
PSD835G2
PSD8XX Family
Each of the two PLDs has unique characteristics suited for its applications They are
described in the following sections.
The
PSD835G2
Functional
Blocks
(cont.)
9.2.1 Decode PLD (DPLD)
The DPLD, shown in Figure 11, is used for decoding the address for internal and external
components. The DPLD can generate the following decode signals:
• 8 sector selects for the main Flash memory (three product terms each)
• 4 sector selects for the Flash Boot memory
(three product terms each)
• 1 internal SRAM select signal (three product terms)
• 1 internal CSIOP (PSD configuration register) select signal
• 1 JTAG select signal (enables JTAG-ISP on Port E)
• 2 internal peripheral select signals (peripheral I/O mode).
9.2.2 Complex PLD (CPLD)
The CPLD can be used to implement system logic functions, such as loadable counters
and shift registers, system mailboxes, handshaking protocols, state machines, and
random logic. The CPLD can also be used to generate 8 external chip selects, routed to
Port C or F. Although external chip selects can be produced by any Output Micro Cell,
these eight external chip selects on Port C or F do not consume any Output Micro Cells.
As shown in Figure 10, the CPLD has the following blocks:
• 24 Input Micro Cells (IMCs)
• 16 Output Micro Cells (OMCs)
• Product Term Allocator
• AND array capable of generating up to 196 product terms
• Four I/O ports.
Each of the blocks are described in the subsections that follow.
The Input and Output Micro Cells are connected to the PSD835G2 internal data bus and
can be directly accessed by the microcontroller. This enables the MCU software to load
data into the Output Micro Cells or read data from both the Input and Output
Micro Cells. This feature allows efficient implementation of system logic and eliminates
the need to connect the data bus to the AND logic array as required in most standard PLD
macrocell architectures.
35
CSBOOT 0
CSBOOT 1
CSBOOT 2
CSBOOT 3
3
3
3
3
4 SECONDARY
FLASH MEMORY
SECTOR SELECTS
(INPUTS)
(32)
3
3
3
3
3
3
3
3
FS0
I/O PORTS (PORT A,B,C,F)
(8)
MCELLA.FB [7:0] (FEEDBACKS)
MCELLB.FB [7:0] (FEEDBACKS)
(8)
(8)
8 FLASH MEMORY
SECTOR SELECTS
PGR0 -PGR7
(16)
(4)
[
]
A 15:0
*
[
]
PD 3:0 (ALE,CLKIN,CSI)
PDN (APD OUTPUT)
(1)
(3)
(1)
(1)
FS7
[
] (
CNTRL 2:0 READ/WRITE CONTROL SIGNALS)
RESET
RS0
3
SRAM SELECT
RD_BSY
CSIOP
I/O DECODER
SELECT
PSEL0
PERIPHERAL I/O MODE
SELECT
PSEL1
JTAGSEL
*NOTE: 1. The address inputs are A[19:4] in 80C51XA mode.
2. Additional address lines can be brought into PSD via Port A, B, C, D or F.
PSD835G2 Beta Information
PSD8XX Family
Figure 12. The Micro Cell and I/O Port
M U X
M U X
M U X
M U X
A N D A R R A Y
P L D I N P U T B U S
P L D I N P U T B U S
37
PSD8XX Family
PSD835G2
9.2.2.1 Output Micro Cell
The
Eight of the Output Micro Cells are connected to Port A pins are named as McellA0-7.
The other eight Micro Cells are connected to Port B pins are named as McellB0-7.
PSD835G2
Functional
Blocks
(cont.)
Table 13. Output Micro Cell Port and Data Bit Assignments
Maximum
Native
Product
Terms
Borrowed
Product
Terms
Data Bit for
Loading or
Reading
Output
Micro Cell
Port
Assignment
McellA0
McellA1
McellA2
McellA3
McellA4
McellA5
McellA6
McellA7
McellB0
McellB1
McellB2
McellB3
McellB4
McellB5
McellB6
McellB7
Port A0
Port A1
Port A2
Port A3
Port A4
Port A5
Port A6
Port A7
Port B0
Port B1
Port B2
Port B3
Port B4
Port B5
Port B6
Port B7
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
5
5
5
5
6
6
6
6
D0
D1
D2
D3
D4
D5
D6
D7
D0
D1
D2
D3
D4
D5
D6
D7
The Output Micro Cell (OMC) architecture is shown in Figure 13. As shown in the figure,
there are native product terms available from the AND array, and borrowed product terms
available (if unused) from other OMCs. The polarity of the product term is controlled by the
XOR gate. The OMC can implement either sequential logic, using the flip-flop element, or
combinatorial logic. The multiplexer selects between the sequential or combinatorial logic
outputs. The multiplexer output can drive a Port pin and has a feedback path to the AND
array inputs.
The flip-flop in the OMC can be configured as a D, T, JK, or SR type in the PSDsoft
program. The flip-flop’s clock, preset, and clear inputs may be driven from a product term
of the AND array. Alternatively, the external CLKIN signal can be used for the clock input
to the flip-flop. The flip-flop is clocked on the rising edge of the clock input. The preset and
clear are active-high inputs. Each clear input can use up to two product terms.
38
PSD835G2
PSD8XX Family
9.2.2.2 The Product Term Allocator
The
The CPLD has a Product Term Allocator. The PSDsoft uses the Allocator to borrow and
place product terms from one Micro Cell to another. The following list summarizes how
product terms are allocated:
PSD835G2
Functional
Blocks
(cont.)
• McellA0-7 all have three native product terms and may borrow up to six more
• McellB0-3 all have four native product terms and may borrow up to five more
• McellB4-7 all have four native product terms and may borrow up to six more.
Each Micro Cell may only borrow product terms from certain other Micro Cells. Product
terms already in use by one Micro Cell will not be available for a different Micro Cell.
If an equation requires more product terms than what is available to it, then “external”
product terms will be required, which will consume other OMCs. If external product terms
are used, extra delay will be added for the equation that required the extra product terms.
This is called product term expansion. PSDsoft will perform this expansion as needed.
9.2.2.3 Loading and Reading the Output Micro Cells (OMCs)
The OMCs occupy a memory location in the MCU address space, as defined by the
CSIOP (refer to the I/O section). The flip-flops in each of the 16 OMCs can be loaded from
the data bus by a microcontroller. Loading the OMCs with data from the MCU takes priority
over internal functions. As such, the preset, clear, and clock inputs to the flip-flop can be
overridden by the MCU. The ability to load the flip-flops and read them back is useful in
such applications as loadable counters and shift registers, mailboxes, and handshaking
protocols. Data is loaded to the OMCs on the trailing edge of the WR signal .
9.2.2.4 The OMC Mask Register
There is one Mask Register for each of the two groups of eight OMCs. The Mask Registers
can be used to block the loading of data to individual OMCs. The default value for the
Mask Registers is 00h, which allows loading of the OMCs. When a given bit in a Mask
Register is set to a ‘1’, the MCU will be blocked from writing to the associated OMC. For
example, suppose McellA0-3 are being used for a state machine. You would not want a
MCU write to McellA to overwrite the state machine registers. Therefore, you would want to
load the Mask Register for McellA (Mask Micro Cell A) with the value 0Fh.
9.2.2.5 The Output Enable of the OMC
The OMC can be connected to an I/O port pin as a PLD output. The output enable of each
Port pin driver is controlled by a single product term from the AND array, ORed with the
Direction Register output. The pin is enabled upon power up if no output enable equation
is defined and if the pin is declared as a PLD output in PSDsoft.
If the OMC output is declared as an internal node and not as a Port pin output in the
PSDabel file, then the Port pin can be used for other I/O functions. The internal node
feedback can be routed as an input to the AND array.
39
PSD8XX Family
PSD835G2
The
Figure 13. CPLD Output Micro Cell
PSD835G2
Functional
Blocks
(cont.)
A N D A R R A Y
P L D I N P U T B U S
40
PSD835G2
PSD8XX Family
9.2.2.6 Input Micro Cells (IMCs)
The
The CPLD has 24 IMCs, one for each pin on Ports A, B, and C. The architecture of the IMC
is shown in Figure 14. The IMCs are individually configurable, and can be used as a latch,
register, or to pass incoming Port signals prior to driving them onto the PLD input bus. The
outputs of the IMCs can be read by the microcontroller through the internal data bus.
PSD835G2
Functional
Blocks
(cont.)
The enable for the latch and clock for the register are driven by a multiplexer whose inputs
are a product term from the CPLD AND array or the MCU address strobe (ALE/AS). Each
product term output is used to latch or clock four IMCs. Port inputs 3-0 can be controlled by
one product term and 7-4 by another.
Configurations for the IMCs are specified by PSDsoft. Outputs of the IMCs can be read by
the MCU via the IMC buffer. See the I/O Port section on how to read the IMCs.
IMCs can use the address strobe to latch address bits higher than A15. Any latched
addresses are routed to the PLDs as inputs.
IMCs are particularly useful with handshaking communication applications where two
processors pass data back and forth through a common mailbox. Figure 15 shows a typical
configuration where the Master MCU writes to the Port A Data Out Register. This, in turn,
can be read by the Slave MCU via the activation of the “Slave-Read” output enable product
term. The Slave can also write to the Port A IMCs and the Master can then read the IMCs
directly. Note that the “Slave-Read” and “Slave-Wr” signals are product terms that are
derived from the Slave MCU inputs RD, WR, and Slave_CS.
Figure 14. Input Micro Cell
INTERNAL DATA BUS
_
INPUT MICRO CELL RD
DIRECTION
REGISTER
(
)
ENABLE .OE
OUTPUT
MICRO CELLS A
AND
PT
PT
MICRO CELL B
I/O PIN
PORT
DRIVER
MUX
Q
D
PT
ALE/AS
MUX
D FF
Q
D
G
FEEDBACK
LATCH
INPUT MICRO CELL
41
PSD8XX Family
PSD835G2
The
Figure 15. Handshaking Communication Using Input Micro Cells
PSD835G2
Functional
Blocks
(cont.)
PSD835G2
SLAVE–CS
RD
WR
SLAVE–READ
PORT A
DATA OUT
REGISTER
SLAVE
MCU
[
]
D 7:0
CPLD
MCU-RD
MCU-WR
D
Q
PORT A
MCU-WR
MASTER
MCU
SLAVE–WR
[
]
D 7:0
PORT A
INPUT
MICRO CELL
Q
D
MCU-RD
9.2.2.7 External Chip Select
The CPLD also provides eight chip select outputs that can be used to select external
devices. The chip selects can be routed to either Port C or Port F, depending on the pin
declaration in the PSDsoft. Each chip select (ECS0-7) consists of one product term that can
be configured active high or low.
The output enable of the pin is controlled by either the output enable product term or the
Direction Register. (See Figure 16).
Figure 16. External Chip Select
ENABLE (.OE) PT
DIRECTION
REGISTER
CPLD
AND
ARRAY
ECS
TO PORT C OR F
ECS PT
PORT PIN
PORT C OR PORT F
POLARITY
BIT
42
PSD835G2
PSD8XX Family
The
9.3 Microcontroller Bus Interface
The “no-glue logic” PSD835G2 Microcontroller Bus Interface can be directly connected to
most popular microcontrollers and their control signals. Key 8-bit microcontrollers with their
bus types and control signals are shown in Table 14. The MCU interface type is
specified using the PSDsoft.
PSD835G2
Functional
Blocks
(cont.)
Table 14. Microcontrollers and their Control Signals
Data
Bus
MCU
Width CNTL0 CNTL1
CNTL2
PC7 PD0** ADIO0 PF3-PF0 PF7-PF4
8031/8051
80C51XA
80C251
80C251
80198
8
8
8
8
8
8
8
8
8
8
8
8
WR
WR
WR
WR
WR
R/W
WR
R/W
WR
R/W
R/W
R/W
RD
RD
PSEN
RD
RD
E
PSEN
*
*
*
*
*
*
*
ALE
ALE
ALE
ALE
ALE
AS
A0
A4
A0
A0
A0
A0
A0
A0
A0
A0
A0
A0
*
*
*
*
*
*
*
*
*
PSEN
A3-A0
*
*
*
*
*
*
*
PSEN
*
*
*
*
*
*
*
*
68HC11
68HC05C0
68HC912
Z80
RD
E
AS
DBE
AS
RD
DS
DS
E
*
*
*
*
*
AS
D3-D0 D7-D4
Z8
*
*
*
*
68330
AS
M37702M2
ALE
D3-D0 D7-D4
**Unused CNTL2 pin can be configured as PLD input. Other unused pins (PD3-0, PA3-0) can be
**configured for other I/O functions.
**ALE/AS input is optional for microcontrollers with a non-multiplexed bus
9.3.1. PSD835G2 Interface to a Multiplexed Bus
Figure 17 shows an example of a system using a microcontroller with a 8-bit multiplexed
bus and a PSD835G2. The ADIO port on the PSD835G2 is connected directly to the
microcontroller address/data bus. ALE latches the address lines internally. Latched
addresses can be brought out to Port E, F or G. The PSD835G2 drives the ADIO data bus
only when one of its internal resources is accessed and the RD input is active. Should the
system address bus exceed sixteen bits, Ports A, B, C, or F may be used as additional
address inputs.
9.3.2. PSD835G2 Interface to a Non-Multiplexed Bus
Figure 18 shows an example of a system using a microcontroller with a 8-bit
non-multiplexed bus and a PSD835G2. The address bus is connected to the ADIO Port,
and the data bus is connected to Port F. Port F is in tri-state mode when the PSD835G2
is not accessed by the microcontroller. Should the system address bus exceed sixteen
bits, Ports A, B or C may be used for additional address inputs.
43
PSD8XX Family
PSD835G2
The
Figure 17. An Example of a Typical 8-Bit Multiplexed Bus Interface
PSD835G2
Functional
Blocks
(cont.)
PSD835G2
[
]
AD 7:0
MICRO-
CONTROLLER
[
]
A 7:0
PORT
F
(
(
)
)
OPTIONAL
ADIO
PORT
[
]
A 15:8
[
]
A 15:8
PORT
G
OPTIONAL
(
)
WR
RD
WR CNTRL0
(
)
RD CNTRL1
PORT
A,B, or
C
(
)
[
]
BHE
BHE CNTRL2
A 23:16
(
)
OPTIONAL
RST
ALE
(
)
ALE PD0
PORT D
RESET
Figure 18. An Example of a Typical 8-Bit Non-Multiplexed Bus Interface
PSD835G2
[
]
D 7:0
[
]
D 7:0
PORT
F
MICRO-
ADIO
CONTROLLER
PORT
[
]
A 15:0
PORT
G
(
)
WR
RD
WR CNTRL0
(
)
RD CNTRL1
[
]
A 23:16
PORT
A,B or
C
(
)
BHE
BHE CNTRL2
RST
(OPTIONAL)
ALE
(
)
ALE PD0
PORT D
RESET
44
PSD835G2
PSD8XX Family
9.3.3 Microcontroller Interface Examples
The
Figures 19 through 23 show examples of the basic connections between the PSD835G2
and some popular microcontrollers. The PSD835G2 Control input pins are labeled as to
the microcontroller function for which they are configured. The MCU interface is specified
using the PSDsoft.
PSD835G2
Functional
Blocks
(cont.)
9.3.3.1 80C31
Figure 19 shows the interface to the 80C31, which has an 8-bit multiplexed address/data
bus. The lower address byte is multiplexed with the data bus. The microcontroller control
signals PSEN, RD, and WR may be used for accessing the internal memory components
and I/O Ports. The ALE input (pin PD0) latches the address.
9.3.3.2 80C251
The Intel 80C251 microcontroller features a user-configurable bus interface with four
possible bus configurations, as shown in Table 15.
Configuration 1 is 80C31 compatible, and the bus interface to the PSD835G2 is identical to
that shown in Figure 19. Configurations 2 and 3 have the same bus connection as shown
in Figure 20. There is only one read input (PSEN) connected to the Cntl1 pin on the
PSD835G2. The A16 connection to the PA0 pin allows for a larger address input to the
PSD835G2. Configuration 4 is shown in Figure 21. The RD signal is connected to Cntl1
and the PSEN signal is connected to the CNTL2.
The 80C251 has two major operating modes: Page Mode and Non-Page Mode. In
Non-Page Mode, the data is multiplexed with the lower address byte, and ALE is active in
every bus cycle. In Page Mode, data D[7:0] is multiplexed with address A[15:8]. In a bus
cycle where there is a Page hit, the ALE signal is not active and only addresses A[7:0]
are changing. The PSD835G2 supports both modes. In Page Mode, the PSD bus timing
is identical to Non-Page Mode except the address hold time and setup time with respect
to ALE is not required. The PSD access time is measured from address A[7:0] valid to
data in valid.
45
PSD8XX Family
PSD835G2
The
Table 15. 80C251 Configurations
PSD835G2
Functional
Blocks
(cont.)
Configuration
80C251
Read/Write
Pins
Connecting to
PSD835G2
Pins
Page Mode
WR
RD
PSEN
CNTL0
CNTL1
CNTL2
Non-Page Mode, 80C31 compatible
A[7:0] multiplex with D[7:0}
1
WR
PSEN only
CNTL0
CNTL1
Non-Page Mode
A[7:0] multiplex with D[7:0}
2
3
4
WR
PSEN only
CNTL0
CNTL1
Page Mode
A[15:8] multiplex with D[7:0}
WR
RD
PSEN
CNTL0
CNTL1
CNTL2
Page Mode
A[15:8] multiplex with D[7:0}
9.3.3.3 80C51XA
The Philips 80C51XA microcontroller family supports an 8- or 16-bit multiplexed bus that
can have burst cycles. Address bits A[3:0] are not multiplexed, while A[19:4] are
multiplexed with data bits D[15:0] in 16-bit mode. In 8-bit mode, A[11:4] are multiplexed
with data bits D[7:0].
The 80C51XA can be configured to operate in eight-bit data mode. (shown in Figure 22).
The 80C51XA improves bus throughput and performance by executing Burst cycles for
code fetches. In Burst Mode, address A19-4 are latched internally by the PSD835G2, while
the 80C51XA changes the A3-0 lines to fetch up to 16 bytes of code. The PSD access
time is then measured from address A3-A0 valid to data in valid. The PSD bus timing
requirement in Burst Mode is identical to the normal bus cycle, except the address setup
and hold time with respect to ALE does not apply.
9.3.3.4 68HC11
Figure 23 shows an interface to a 68HC11 where the PSD835G2 is configured in 8-bit
multiplexed mode with E and R/W settings. The DPLD can generate the READ and WR
signals for external devices.
46
PSD835G2
PSD8XX Family
Figure 19. Interfacing the PSD835G2 with an 80C31
A[15:8]
AD[7:0]
A[15:8]
AD[7:0]
V
V
CC
9
29
69
V
V
CC
CC
CC
39
31
32
33
34
35
36
37
38
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
3
4
5
6
7
10
11
12
19
X1
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
38
37
36
35
34
33
32
CRYSTAL
18
9
X2
RESET
RESET
21
22
23
24
25
26
27
28
21
22
23
24
25
26
27
28
A8
A9
13
14
15
16
17
18
19
20
12
13
14
INT0
INT1
T0
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
ADIO8
ADI09
A10
A11
A12
A13
A14
A15
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
15
T1
1
2
3
4
5
6
7
8
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
51
52
53
54
55
56
57
58
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
16
17
WR
RD
59
WR
RD
CNTL0 (WR)
CNTL1 (RD)
60
PSEN
ALE
29
30
40
PSEN
ALE/P
CNTL2 (PSEN)
79
80
1
PD0 (ALE)
PD1 (CLKIN)
PD2 (CSI)
PD3
10
11
RXD
61
62
63
64
65
66
67
68
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
2
TXD
31
EA/VP
RESET
39
RESET
80C31
71
72
73
74
75
76
77
78
PE0 (TMS)
PE1 (TCK/ST)
PE2 (TDI)
PE2 (TDO)
PE4 (TSTAT/RDY)
PE5 (TERR)
41
42
43
44
45
46
47
48
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
RESET
RESET
PE6 (VSTBY)
PE7 (VBATON)
GND GND GND GND GND
30 49 50 70
8
PSD835G2
47
PSD8XX Family
PSD835G2
Figure 20. Interfacing the PSD835G2 to the 80C251, with One Read Input
A[17:8]
AD[7:0]
A[15:8]
AD[7:0]
V
CC
A17
U1
9
29
69
V
V
CC
V
CC
CC
2
3
4
5
6
7
8
9
43
42
41
40
39
38
37
36
A0
A1
A2
A3
A4
A5
A6
A7
31
A16
A17
3
4
5
6
7
10
11
12
*
P1.0
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
**
32
33
34
35
36
37
38
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
21
20
24
25
26
27
28
29
30
31
AD8
AD9
21
22
23
24
25
26
27
28
13
14
15
16
17
18
19
20
X1
X2
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
ADIO8
ADIO9
CRYSTAL
AD10
AD11
AD12
AD13
AD14
AD15
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
11
13
14
15
16
17
P3.0/RXD
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
51
52
53
54
55
56
57
58
P3.5/T1
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
18
19
32
WR
59
60
WR
RD/A16
PSEN
CNTL0 (WR)
CNTL1 (RD)
A16
10
RESET
RESET
EA
40
CNTL2 (PSEN)
35
RD
ALE
79
80
1
PD0 (ALE)
PD1 (CLKIN)
PD2 (CSI)
PD3
33
61
62
63
64
65
66
67
68
ALE
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
2
80C251SB
RESET
39
RESET
71
72
73
74
75
76
77
78
PE0 (TMS)
PE1 (TCK/ST)
PE2 (TDI)
PE3 (TDO)
PE4 (TSTAT/RDY)
PE5 (TERR)
41
42
43
44
45
46
47
48
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
RESET
RESET
PE6 (VSTBY)
PE7 (VBATON)
GND GND GND GND GND
30 49 50 70
8
PSD835G2
**Connection is optional.
**Non-page mode: AD[7:0] - ADIO[7:0].
48
PSD835G2
PSD8XX Family
Figure 21. Interfacing the PSD835G2 to the 80C251, with Read and PSEN Inputs
AD[15:8]
A[7:0]
AD[15:8]
A[7:0]
V
CC
9
29
69
V
V
CC
V
CC
CC
2
3
4
5
6
7
8
9
43
42
41
40
39
38
37
36
A0
A1
A2
A3
A4
A5
A6
A7
31
3
4
5
6
7
10
11
12
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PF0
**
32
33
34
35
36
37
38
PF1
PF2
PF3
PF4
PF5
PF6
PF7
21
20
24
25
26
27
28
29
30
31
AD8
AD9
21
22
23
24
25
26
27
28
13
14
15
16
17
18
19
20
X1
X2
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
ADIO8
ADI09
CRYSTAL
AD10
AD11
AD12
AD13
AD14
AD15
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
11
13
14
15
16
17
P3.0/RXD
P3.1/TXD
P3.2/INT0
P3.3/INT1
P3.4/T0
51
52
53
54
55
56
57
58
P3.5/T1
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
18
WR
RD
59
WR
RD/A16
CNTL0 (WR)
CNTL1 (RD)
19
60
10
RESET
RESET
EA
PSEN
ALE
32
40
PSEN
ALE
CNTL2 (PSEN)
35
33
79
80
1
PD0 (ALE)
PD1 (CLKIN)
PD2 (CSI)
PD3
61
62
63
64
65
66
67
68
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
2
80C251SB
RESET
39
RESET
71
72
73
74
75
76
77
78
PE0 (TMS)
PE1 (TCK/ST)
PE2 (TDI)
PE3 (TDO)
PE4 (TSTAT/RDY)
PE5 (TERR)
41
42
43
44
45
46
47
48
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
RESET
RESET
PE6 (VSTBY)
PE7 (VBATON)
GND GND GND GND GND
30 49 50 70
8
PSD835G2
49
PSD8XX Family
PSD835G2
Figure 22. Interfacing the PSD835G2 to the 80C51XA, 8-Bit Data Bus
A[19:12] D[7:0]
A[3:0]
V
V
CC
9
29
69
V
V
CC
CC
CC
A0
A1
A2
A3
21
20
43
42
41
40
39
38
37
36
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
31
32
33
34
35
36
37
38
3
4
5
6
7
10
11
12
XTAL1
XTAL2
A4D0
A5D1
A6D2
A7D3
A8D4
A9D5
A10D6
A11D7
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
CRYSTAL
11
13
6
RXD0
TXD0
RXD1
TXD1
7
24
25
26
27
28
29
30
31
A12
A13
A14
A15
A16
A17
A18
A19
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
A12D8
A13D9
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
ADIO8
ADI09
9
8
16
T2EX
T2
T0
A14D10
A15D11
A16D12
A17D13
A18D14
A19D15
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
51
52
53
54
55
56
57
58
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
A3
A2
A1
A0
5
4
3
A3
A2
A1
59
60
CNTL0 (WR)
CNTL1 (RD)
2
A0/WRH
WRL
RD
RESET
WR
18
19
10
14
15
40
RST
INT0
INT1
CNTL2 (PSEN)
RD
79
80
1
V
PD0 (ALE)
PD1 (CLKIN)
PD2 (CSI)
PD3
CC
PSEN
32
PSEN
ALE
35
61
62
63
64
65
66
67
68
EA/WAIT
BUSW
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
2
ALE
33
17
39
RESET
XA-G3
71
72
73
74
75
76
77
78
PE0 (TMS)
PE1 (TCK/ST)
PE2 (TDI)
PE3 (TDO)
PE4 (TSTAT/RDY)
PE5 (TERR)
41
42
43
44
45
46
47
48
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
RESET
PE6 (VSTBY)
PE7 (VBATON)
RESET
GND GND GND GND GND
30 49 50 70
8
PSD835G2
50
PSD835G2
PSD8XX Family
Figure 23. Interfacing the PSD835G2 with a 68HC11
A[15:8]
AD[7:0]
A[15:8]
AD[7:0]
V
V
CC
9
29
69
V
V
CC
CC
CC
9
34
33
32
31
30
29
28
27
31
32
33
34
35
36
37
38
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
3
4
5
6
7
10
11
12
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
ADIO0
ADIO1
ADIO2
ADIO3
ADIO4
ADIO5
ADIO6
ADIO7
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
10
11
12
13
14
15
16
42
41
40
39
38
37
36
35
8
7
21
22
23
24
25
26
27
28
A8
A9
13
14
15
16
17
18
19
20
XT
EX
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
ADIO8
ADIO9
CRYSTAL
A10
A11
A12
A13
A14
A15
ADIO10
ADIO11
ADIO12
ADIO13
ADIO14
ADIO15
19
18
IRQ
XIRQ
20
21
22
23
24
25
PD0
PD1
PD2
PD3
PD4
PD5
51
52
53
54
55
56
57
58
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
RW
E
6
5
59
60
RW
E
CNTL0 (R/W)
CNTL1 (E)
4
40
AS
CNTL2
43
45
47
49
44
46
48
50
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
AS
79
80
1
PD0 (AS)
PD1 (CLKIN)
PD2 (CSI)
PD3
17
RESET
61
62
63
64
65
66
67
68
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
2
RESET
39
RESET
52
51
VRH
VRL
71
72
73
74
75
76
77
78
PE0 (TMS)
PE1 (TCK/ST)
PE2 (TDI)
PE3 (TDO)
PE4 (TSTAT/RDY)
PE5 (TERR)
2
3
41
42
43
44
45
46
47
48
MODB
MODA
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
68HC11E9
PE6 (VSTBY)
PE7 (VBATON)
RESET
GND GND GND GND GND
30 49 50 70
RESET
8
PSD835G2
51
PSD8XX Family
PSD835G2
The
9.4 I/O Ports
There are seven programmable I/O ports: Ports A, B, C, D, E, F and G. Each of the ports
is eight bits except Port D, which is 4 bits. Each port pin is individually user configurable,
thus allowing multiple functions per port. The ports are configured using PSDsoft or by the
microcontroller writing to on-chip registers in the CSIOP address space.
PSD835G2
Functional
Blocks
(cont.)
The topics discussed in this section are:
• General Port Architecture
• Port Operating Modes
• Port Configuration Registers
• Port Data Registers
• Individual Port Functionality.
9.4.1 General Port Architecture
The general architecture of the I/O Port is shown in Figure 24. Individual Port architectures
are shown in Figures 26 through 28. In general, once the purpose for a port pin has been
defined, that pin will no longer be available for other purposes. Exceptions will be noted.
As shown in Figure 24, the ports contain an output multiplexer whose selects are driven
by the configuration bits in the Control Registers (Ports E, F and G only) and PSDsoft
Configuration. Inputs to the multiplexer include the following:
❏ Output data from the Data Out Register
❏ Latched address outputs
❏ CPLD Micro Cell output
❏ External Chip Select from CPLD.
The Port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be
read. The PDB is connected to the Internal Data Bus for feedback and can be read by the
microcontroller. The Data Out and Micro Cell outputs, Direction and Control Registers,
and port pin input are all connected to the PDB.
The Port pin’s tri-state output driver enable is controlled by a two input OR gate whose
inputs come from the CPLD AND array enable product term and the Direction Register. If
the enable product term of any of the array outputs are not defined and that port pin is not
defined as a CPLD output in the PSDabel file, then the Direction Register has sole control
of the buffer that drives the port pin.
The contents of these registers can be altered by the microcontroller. The PDB feedback
path allows the microcontroller to check the contents of the registers.
Ports A, B, and C have embedded Input Micro Cells (IMCs). The IMCs can be configured
as latches, registers, or direct inputs to the PLDs. The latches and registers are clocked by
the address strobe (AS/ALE) or a product term from the PLD AND array. The outputs from
the IMCs drive the PLD input bus and can be read by the microcontroller. Refer to the IMC
subsection of the PLD section.
52
DATA OUT
REG.
DATA OUT
ADDRESS
D
Q
WR
ADDRESS
ALE
PORT PIN
D
G
Q
OUTPUT
MUX
MICRO CELL OUTPUTS
EXT CS
READ MUX
P
D
B
OUTPUT
SELECT
DATA IN
CONTROL REG.
ENABLE OUT
D
Q
WR
WR
DIR REG.
D
Q
(
)
ENABLE PRODUCT TERM .OE
INPUT
MICRO CELL
CPLD-INPUT
PSD8XX Family
PSD835G2
9.4.2 Port Operating Modes
The
The I/O Ports have several modes of operation. Some modes can be defined using
PSDsoft, some by the microcontroller writing to the Registers in CSIOP space, and some
by both. The modes that can only be defined using PSDsoft must be programmed into the
device and cannot be changed unless the device is reprogrammed. The modes that can be
changed by the microcontroller can be done so dynamically at run-time. The PLD I/O,
Data Port, Address Input, Peripheral I/O and MCU Reset modes are the only modes that
must be defined before programming the device. All other modes can be changed by the
microcontroller at run-time.
PSD835G2
Functional
Blocks
(cont.)
Table 16 summarizes which modes are available on each port. Table 17 shows how and
where the different modes are configured. Each of the port operating modes are described
in the following subsections.
Table 16. Port Operating Modes
Port Mode
Port A Port B Port C Port D Port E Port F Port G
MCU I/O
Yes
Yes
Yes
Yes
Yes
Yes
Yes
PLD I/O
McellA Outputs
McellB Outputs
Additional Ext. CS Outputs
PLD Inputs
Yes
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Address Out
No
No
No
No
Yes
(A7-0)
Yes
(A7-0)
Yes
(A7-0)
or
(A15-8)
Address In
Data Port
Yes
No
No
No
Yes
No
No
No
Yes
No
No
No
Yes
No
No
No
No
No
Yes
Yes
Yes
No
No
No
No
No
Peripheral I/O
JTAG ISP
No
Yes*
*Can be multiplexed with other I/O functions.
54
PSD835G2
PSD8XX Family
The
Table 17. Port Operating Mode Settings
PSD835G2
Functional
Blocks
(cont.)
Control
Register
Setting
Direction
Register
Setting
VM
Register
Setting
Defined In
PSDsoft
JTAG
Enable
Mode
1 = output,
0 = input
(Note 1)
0
Declare
pins only
MCU I/O
NA
NA
NA
NA
(Note 3)
Declare pins
and logic
PLD I/O
NA
(Note 1)
equations
Selected for
MCU with
non-mux bus
Data Port
(Port F)
NA
1
NA
NA
NA
NA
NA
Address Out
(Port E, F, G)
Declare
pins only
1 (Note 1)
Declare pins or
logic equation
(Port A,B,C,D,F) for input
Micro Cells
Address In
NA
NA
NA
NA
Peripheral I/O
(Port F)
Logic equations
(PSEL0 & 1)
NA
NA
NA
NA
PIO bit =1
NA
NA
JTAG ISP
(Note 2)
Declare pins
only
JTAG_Enable
*NA = Not Applicable
NOTE: 1. The direction of the Port A,B,C, and F pins are controlled by the Direction Register ORed with the
individual output enable product term (.oe) from the CPLD AND array.
2. Any of these three methods will enable JTAG pins on Port E.
3. Control Register setting is not applicable to Ports A, B and C.
9.4.2.1 MCU I/O Mode
In the MCU I/O Mode, the microcontroller uses the PSD835G2 ports to expand its own
I/O ports. By setting up the CSIOP space, the ports on the PSD4000 are mapped into the
microcontroller address space. The addresses of the ports are listed in Table 6.
A port pin can be put into MCU I/O mode by writing a ‘0’ to the corresponding bit in the
Control Register (Port E, F and G). The MCU I/O direction may be changed by writing to
the corresponding bit in the Direction Register, or by the output enable product term. See
the subsection on the Direction Register in the “Port Registers” section. When the pin is
configured as an output, the content of the Data Out Register drives the pin. When config-
ured as an input, the microcontroller can read the port input through the Data In buffer.
See Figure 22.
Ports A, B and C do not have Control Registers, and are in MCU I/O mode by default.
They can be used for PLD I/O if they are specified in PSDsoft.
9.4.2.2 PLD I/O Mode
The PLD I/O Mode uses a port as an input to the CPLD’s Input Micro Cells, and/or as an
output from the CPLD’s Output Micro Cells. The output can be tri-stated with a control
signal. This output enable control signal can be defined by a product term from the PLD, or
by setting the corresponding bit in the Direction Register to ‘0’. The corresponding bit in the
Direction Register must not be set to ‘1’ if the pin is defined as a PLD input pin in PSDsoft.
The PLD I/O Mode is specified in PSDsoft by declaring the port pins, and then specifying
an equation in PSDsoft.
55
PSD8XX Family
PSD835G2
9.4.2.3 Address Out Mode
The
For microcontrollers with a multiplexed address/data bus, Address Out Mode can be used
to drive latched addresses onto the port pins. These port pins can, in turn, drive external
devices. Either the output enable or the corresponding bits of both the Direction Register
and Control Register must be set to a ‘1’ for pins to use Address Out Mode. This must be
done by the MCU at run-time. See Table 18 for the address output pin assignments on
Ports E, F and F for various MCUs.
PSD835G2
Functional
Blocks
(cont.)
Note: Do not drive address lines with Address Out Mode to an external memory device if
it is intended for the MCU to boot from the external device. The MCU must first boot from
PSD memory so the Direction and Control register bits can be set.
Table 18. I/O Port Latched Address Output Assignments
MCU
Port E (3:0) Port E (7:4) Port F (3:0) Port F (7:4) Port G (3:0) Port G (7:4)
80C51XA
N/A*
N/A
Addr (7:4)
N/A
N/A*
N/A
Addr (7:4)
N/A
Addr (11:8)
N/A
80C251
(Page Mode)
Addr (11:8) Addr (15:12)
All Other
Eight-Bit
Multiplexed
Addr (3:0)
N/A
Addr (7:4)
N/A
Addr (3:0)
N/A
Addr (7:4)
N/A
Addr (3:0)
Addr (3:0)
Addr (7:4)
Addr (7:4)
8-Bit
Non-Mux
Bus
9.4.2.4 Address In Mode
For microcontrollers that have more than 16 address lines, the higher addresses can be
connected to Ports A, B, C, D or F and are routed as inputs to the PLDs. The address
input can be latched in the Input Micro Cell by the address strobe (ALE/AS). Any
input that is included in the DPLD equations for the Main Flash, Boot Flash, or SRAM is
considered to be an address input.
9.4.2.5 Data Port Mode
Port F can be used as a data bus port for a microcontroller with a non-multiplexed
address/data bus. The Data Port is connected to the data bus of the microcontroller. The
general I/O functions are disabled in Port F if the ports are configured as Data Port. Data
Port Mode is automatically configured in PSDsoft when a non-multiplexed bus MCU is
selected.
9.4.2.6 Peripheral I/O Mode
Peripheral I/O Mode can be used to interface with external 8-bit peripherals. In this mode,
all of Port F serves as a tri-stateable, bi-directional data buffer for the microcontroller.
Peripheral I/O Mode is enabled by setting Bit 7 of the VM Register to a ‘1’. Figure 25
shows how Port A acts as a bi-directional buffer for the microcontroller data bus if
Peripheral I/O Mode is enabled. An equation for PSEL0 and/or PSEL1 must be specified in
PSDsoft. The buffer is tri-stated when PSEL 0 or 1 is not active.
9.4.2.7 JTAG ISP
Port E is JTAG compliant, and can be used for In-System Programming (ISP). You can
multiplex JTAG operations with other functions on Port E because ISP is not performed
during normal system operation. For more information on the JTAG Port, refer to
section 9.6.
56
PSD835G2
PSD8XX Family
The
Figure 25. Peripheral I/O Mode
PSD835G2
Functional
Blocks
(cont.)
RD
PSEL0
PSEL
PSEL1
D0-D7
VM REGISTER BIT 7
PF0-PF7
DATA BUS
WR
9.4.3 Port Configuration Registers (PCRs)
Each port has a set of PCRs used for configuration. The contents of the registers can be
accessed by the microcontroller through normal read/write bus cycles at the addresses
given in Table 6. The addresses in Table 6 are the offsets in hex from the base of the
CSIOP register.
The pins of a port are individually configurable and each bit in the register controls its
respective pin. For example, Bit 0 in a register refers to Bit 0 of its port. The three PCRs,
shown in Table 22, are used for setting the port configurations. The default power-up state
for each register in Table 19 is 00h.
Table 19. Port Configuration Registers
Register Name
Port
MCU Access
Control
E,F,G
Write/Read
Write/Read
Write/Read
Direction
Drive Select*
A,B,C,D,E,F,G
A,B,C,D,E,F,G
*NOTE: See Table 26 for Drive Register bit definition.
57
PSD8XX Family
PSD835G2
9.4.3.1 Control Register
The
Any bit set to ‘0’ in the Control Register sets the corresponding Port pin to MCU I/O Mode,
and a ‘1’ sets it to Address Out Mode. The default mode is MCU I/O. Only Ports E, F and
G have an associated Control Register.
PSD835G2
Functional
Blocks
(cont.)
9.4.3.2 Direction Register
The Direction Register controls the direction of data flow in the I/O Ports. Any bit set to ‘1’
in the Direction Register will cause the corresponding pin to be an output, and any bit set
to ‘0’ will cause it to be an input. The default mode for all port pins is input.
Figures 26 and 28 show the Port Architecture diagrams for Ports A/B/C and E/F/G
respectively. The direction of data flow for Ports A, B, C and F are controlled not only by
the direction register, but also by the output enable product term from the PLD AND array.
If the output enable product term is not active, the Direction Register has sole control of a
given pin’s direction.
An example of a configuration for a port with the three least significant bits set to output
and the remainder set to input is shown in Table 22. Since Port D only contains four pins,
the Direction Register for Port D has only the four least significant bits active.
Table 20. Port Pin Direction Control,
Output Enable P.T. Not Defined
Direction Register Bit
Port Pin Mode
Input
0
1
Output
Table 21. Port Pin Direction Control, Output Enable P.T. Defined
Direction Register Bit
Output Enable P.T.
Port Pin Mode
Input
0
0
1
1
0
1
0
1
Output
Output
Output
Table 22. Port Direction Assignment Example
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
1
1
1
58
PSD835G2
PSD8XX Family
9.4.3.3 Drive Select Register
The
The Drive Select Register configures the pin driver as Open Drain or CMOS for some port
pins, and controls the slew rate for the other port pins. An external pull-up resistor should
be used for pins configured as Open Drain.
PSD835G2
Functional
Blocks
(cont.)
A pin can be configured as Open Drain if its corresponding bit in the Drive Select Register
is set to a ‘1’. The default pin drive is CMOS.
Aside: the slew rate is a measurement of the rise and fall times of an output. A higher
slew rate means a faster output response and may create more electrical noise. A pin
operates in a high slew rate when the corresponding bit in the Drive Register is set to ‘1’.
The default rate is slow slew.
Table 23 shows the Drive Register for Ports A, B, C, D, E, F and G. It summarizes which
pins can be configured as Open Drain outputs and which pins the slew rate can be set for.
Table 23. Drive Register Pin Assignment
Drive
Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Port A
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Port B
Port C
Port D
Port E
Port F
Port G
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Open
Drain
59
PSD8XX Family
PSD835G2
The
9.4.4 Port Data Registers
The Port Data Registers, shown in Table 24, are used by the microcontroller to write data
to or read data from the ports. Table 24 shows the register name, the ports having each
register type, and microcontroller access for each register type. The registers are
described below.
PSD835G2
Functional
Blocks
(cont.)
9.4.4.1 Data In
Port pins are connected directly to the Data In buffer. In MCU I/O input mode, the pin input
is read through the Data In buffer.
9.4.4.2 Data Out Register
Stores output data written by the MCU in the MCU I/O output mode. The contents of the
Register are driven out to the pins if the Direction Register or the output enable
product term is set to “1”. The contents of the register can also be read back by the
microcontroller.
9.4.4.3 Output Micro Cells (OMCs)
The CPLD OMCs occupy a location in the microcontroller’s address space. The
microcontroller can read the output of the OMCs. If the Mask Micro Cell Register bits are
not set, writing to the Micro Cell loads data to the Micro Cell flip flops. Refer to the PLD
section for more details.
9.4.4.4 Mask Micro Cell Register
Each Mask Register bit corresponds to an OMC flip flop. When the Mask Register bit
is set to a “1”, loading data into the OMC flip flop is blocked. The default value is “0” or
unblocked.
9.4.4.5 Input Micro Cells (IMCs)
The IMCs can be used to latch or store external inputs. The outputs of the IMCs
are routed to the PLD input bus, and can be read by the microcontroller. Refer to the PLD
section for a detailed description.
9.4.4.6 Enable Out
The Enable Out register can be read by the microcontroller. It contains the output enable
values for a given port. A “1” indicates the driver is in output mode. A “0” indicates the
driver is in tri-state and the pin is in input mode.
Table 24. Port Data Registers
Register Name
Data In
Port
MCU Access
A,B,C,D,E,F,G Read – input on pin
A,B,C,D,E,F,G Write/Read
Data Out
Output Micro Cell A,B
Read – outputs of Micro Cells
Write – loading Micro Cells Flip-Flop
Mask Micro Cell
A,B
Write/Read – prevents loading into a given
Micro Cell
Input Micro Cell
Enable Out
A,B,C
Read – outputs of the Input Micro Cells
A,B,C,F
Read – the output enable control of the port driver
60
PSD835G2
PSD8XX Family
The
9.4.5 Ports A, B and C – Functionality and Structure
Ports A and B have similar functionality and structure, as shown in Figure 26. The two
ports can be configured to perform one or more of the following functions:
PSD835G2
Functional
Blocks
(cont.)
❏ MCU I/O Mode
❏ CPLD Output – Micro Cells McellA[7:0] can be connected to Port A.
McellB[7:0] can be connected to Port B.
External chip select ECS [7:0] can be connected to Port C.
❏ CPLD Input – Via the input Micro Cells.
❏ Address In – Additional high address inputs using the Input Micro Cells.
❏ Open Drain/Slew Rate – pins PC[7:0]can be configured to fast slew rate,
pins PA[7:0] and PB[7:0] can be configured to Open Drain
Mode.
Figure 26. Port A, B and C
I N T E R N A L D A T A B U S
61
PSD8XX Family
PSD835G2
The
9.4.6 Port D – Functionality and Structure
Port D has four I/O pins. See Figure 27. Port D can be configured to program one more of
PSD835G2
Functional
Blocks
(cont.)
the following functions:
❏ MCU I/O Mode
❏ CPLD Input – direct input to CPLD, no Input Micro Cells
Port D pins can be configured in PSDsoft as input pins for other dedicated functions:
❏ PD0 – ALE, as address strobe input
❏ PD1 – CLKIN, as clock input to the Micro Cells Flip Flops and APD counter
❏ PD2 – CSI, as active low chip select input. A high input will disable the
Flash/SRAM and CSIOP.
❏ PD3 – as DBE input from 68HC912
9.4.7 Port E – Functionality and Structure
Port E can be configured to perform one or more of the following functions (see Figure 28):
❏ MCU I/O Mode
❏ In-System Programming – JTAG port can be enabled for programming/erase of the
PSD8XX device. (See Section 9.6 for more information on JTAG programming.)
❏ Open Drain – Port E pins can be configured in Open Drain Mode
❏ Battery Backup features – PE6 can be configured as a Battery Input (Vstby) pin.
PE7 can be configured as a Battery On Indicator output
pin, indicating when Vcc is less than Vbat.
❏ Latched Address Output – Provided latched address (A7-0) output
Figure 27. Port D Structure
DATA OUT
REG.
DATA OUT
D
Q
WR
PORT D PIN
OUTPUT
MUX
READ MUX
OUTPUT
SELECT
P
D
B
DATA IN
DIR REG.
D
Q
WR
CPLD-INPUT
62
PSD835G2
PSD8XX Family
The
9.4.8 Port F – Functionality and Structure
Port F can be configured to perform one or more of the following functions:
PSD4000
Functional
Blocks
(cont.)
❏ MCU I/O Mode
❏ CPLD Output – external chip select ECS[7:0] can be connected to Port F (or Port C).
❏ CPLD Input – as direct input ot the CPLD array.
❏ Address In – additional high address inputs. Direct input to the CPLD array, no Input
Micro Cells latching is available.
❏ Latched Address Out – Provide latched address out per Table 29.
❏ Slew Rate – pins can be set up for fast slew rate.
❏ Data Port – connected to D[7:0] when Port F is configured as Data Port for a
non-multiplexed bus.
❏ Peripheral I/O Mode
9.4.9 Port G – Functionality and Structure
Port G can be configured to perform one or more of the following functions:
❏ MCU I/O Mode
❏ Latched Address Out – provide latched address out per Table 29.
❏ Open Drain – pins can be configured in Open Drain Mode
Figure 28. Ports E, F and G Structure
DATA OUT
REG.
DATA OUT
D
Q
WR
ADDRESS
ALE
ADDRESS
PORT PIN
D
G
Q
[
]
[
]
A 7:0 OR A 15:8
OUTPUT
MUX
EXT. CS (PORT F)
READ MUX
P
D
B
OUTPUT
SELECT
DATA IN
CONTROL REG.
ENABLE OUT
D
Q
WR
WR
DIR REG.
D
Q
(
)
ENABLE PRODUCT TERM .OE
CPLD INPUT (PORT F)
ISP OR BATTERY BACK-UP (PORT E)
CONFIGURATION
BIT
63
PSD8XX Family
PSD835G2
The
9.5 Power Management
The PSD835G2 offers configurable power saving options. These options may be used
individually or in combinations, as follows:
PSD835G2
Functional
Blocks
(cont.)
❏ All memory types in a PSD (Flash, Secondary Flash, and SRAM) are built with
Zero-Power technology. In addition to using special silicon design methodology,
Zero-Power technology puts the memories into standby mode when address/data
inputs are not changing (zero DC current). As soon as a transition occurs on an input,
the affected memory “wakes up”, changes and latches its outputs, then goes back to
standby. The designer does not have to do anything special to achieve memory
standby mode when no inputs are changing—it happens automatically.
The PLD sections can also achieve standby mode when its inputs are not changing,
see PMMR registers below.
❏ Like the Zero-Power feature, the Automatic Power Down (APD) logic allows the PSD to
reduce to standby current automatically. The APD will block MCU address/data signals
from reaching the memories and PLDs. This feature is available on all PSD835G2
devices. The APD unit is described in more detail in section 9.5.1.
Built in logic will monitor the address strobe of the MCU for activity. If there is no
activity for a certain time period (MCU is asleep), the APD logic initiates Power Down
Mode (if enabled). Once in Power Down Mode, all address/data signals are blocked
from reaching PSD memories and PLDs, and the memories are deselected internally.
This allows the memories and PLDs to remain in standby mode even if the
address/data lines are changing state externally (noise, other devices on the MCU
bus, etc.). Keep in mind that any unblocked PLD input signals that are changing states
keeps the PLD out of standby mode, but not the memories.
❏ The PSD Chip Select Input (CSI) can be used to disable the internal memories,
placing them in standby mode even if inputs are changing. This feature does not block
any internal signals or disable the PLDs. This is a good alternative to using the APD
logic, especially if your MCU has a chip select output. There is a slight penalty in
memory access time when the CSI signal makes its initial transition from deselected
to selected.
❏ The PMMR registers can be written by the MCU at run-time to manage power. All PSD
devices support “blocking bits” in these registers that are set to block designated
signals from reaching both PLDs. Current consumption of the PLDs is directly related
to the composite frequency of the changes on their inputs (see Figures 32 and 32a).
Significant power savings can be achieved by blocking signals that are not used in
PLD logic equations at run time. PSDsoft creates a fuse map that automatically blocks
the low address byte (A7-A0) or the control signals (CNTL0-2, ALE and WRH/DBE) if
none of these signals are used in PLD logic equations.
The PSD835G2 devices have a Turbo Bit in the PMMR0 register. This bit can be set
to disable the Turbo Mode feature (default is Turbo Mode on). While Turbo Mode is
disabled, the PLDs can achieve standby current when no PLD inputs are changing
(zero DC current). Even when inputs do change, significant power can be saved at
lower frequencies (AC current), compared to when Turbo Mode is enabled. Conversely,
when the Turbo Mode is enabled, there is a significant DC current component and the
AC component is higher.
9.5.1 Automatic Power Down (APD) Unit and Power Down Mode
The APD Unit, shown in Figure 24, puts the PSD into Power Down Mode by monitoring
the activity of the address strobe (ALE/AS). If the APD unit is enabled, as soon as activity
on the address strobe stops, a four bit counter starts counting. If the address strobe
remains inactive for fifteen clock periods of the CLKIN signal, the Power Down (PDN)
signal becomes active, and the PSD will enter into Power Down Mode, discussed next.
64
PSD835G2
PSD8XX Family
9.5.1 Automatic Power Down (APD) Unit and Power Down Mode (cont.)
The
PSD835G2
Functional
Blocks
(cont.)
Power Down Mode
By default, if you enable the PSD APD unit, Power Down Mode is automatically enabled.
The device will enter Power Down Mode if the address strobe (ALE/AS) remains inactive
for fifteen CLKIN (pin PD1) clock periods.
The following should be kept in mind when the PSD is in Power Down Mode:
• If the address strobe starts pulsing again, the PSD will return to normal operation.
The PSD will also return to normal operation if either the CSI input returns low or the
Reset input returns high.
• The MCU address/data bus is blocked from all memories and PLDs.
• Various signals can be blocked (prior to Power Down Mode) from entering the PLDs
by setting the appropriate bits in the PMMR registers. The blocked signals include
MCU control signals and the common clock (CLKIN). Note that blocking CLKIN from
the PLDs will not block CLKIN from the APD unit.
• All PSD memories enter Standby Mode and are drawing standby current. However,
the PLDs and I/O ports do not go into Standby Mode because you don’t want to
have to wait for the logic and I/O to “wake-up” before their outputs can change. See
Table 25 for Power Down Mode effects on PSD ports.
• Typical standby current is 50 µA for 5 V parts. This standby current value assumes
that there are no transitions on any PLD input.
Table 25. Power Down Mode’s Effect on
Ports
Port Function
MCU I/O
Pin Level
No Change
No Change
Undefined
PLD Out
Address Out
Data Port
Three-State
Three-State
Peripheral I/O
Table 26. PSD835G2 Timing and Standby Current During Power
Down Mode
Access
Recovery Time
to Normal
Access
5V V ,
CC
PLD
Propagation
Delay
Memory
Access
Time
Typical
Standby
Current
Mode
Normal tpd
(Note 1)
50 µA
(Note 2)
Power Down
No Access
tLVDV
NOTES: 1. Power Down does not affect the operation of the PLD. The PLD operation in this
mode is based only on the Turbo Bit.
2. Typical current consumption assuming no PLD inputs are changing state and
the PLD Turbo bit is off.
65
PSD8XX Family
PSD835G2
The
Figure 29. APD Logic Block
PSD835G2
Functional
Blocks
(cont.)
APD EN
PMMR0 BIT 1=1
TRANSITION
DETECTION
DISABLE BUS
INTERFACE
ALE
PD
CLR
APD
SECONDARY
FLASH SELECT
COUNTER
RESET
MAIN FLASH SELECT
EDGE
DETECT
PD
CSI
PLD
SRAM SELECT
POWER DOWN
CLKIN
(
)
PDN SELECT
DISABLE MAIN AND
SECONDARY FLASH/SRAM
Figure 30. Enable Power Down Flow Chart
RESET
Enable APD
Set PMMR0 Bit 1 = 1
OPTIONAL
Disable desired inputs to PLD
by setting PMMR0 bits 4 and 5
and PMMR2 bits 0.
ALE/AS idle
for 15 CLKIN
clocks?
No
Yes
PSD in Power
Down Mode
66
PSD835G2
PSD8XX Family
The
Table 27. Power Management Mode Registers (PMMR0, PMMR2)**
PMMR0
PSD835G2
Functional
Blocks
(cont.)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PLD
PLD
PLD
Turbo
APD
Enable
*
*
*
*
Mcell clk Array clk
1 = off 1 = off
1 = off
1 = on
***Bits 0, 2, 6, and 7 are not used, and should be set to 0.
***The PMMR0, and PMMR2 register bits are cleared to zero following power up.
***Subsequent reset pulses will not clear the registers.
Bit 1 0 = Automatic Power Down (APD) is disabled.
1 = Automatic Power Down (APD) is enabled.
Bit 3 0 = PLD Turbo is on.
1 = PLD Turbo is off, saving power.
Bit 4 0 = CLKIN input to the PLD AND array is connected.
Every CLKIN change will power up the PLD when Turbo bit is off.
1 = CLKIN input to PLD AND array is disconnected, saving power.
Bit 5 0 = CLKIN input to the PLD Micro Cells is connected.
1 = CLKIN input to PLD Micro Cells is disconnected, saving power.
PMMR2
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PLD
array
DBE
PLD
array
ALE
PLD**
array
CNTL2
PLD**
array
CNTL1
PLD**
array
CNTL0
PLD
array
Addr.
*
*
1 = off
1 = off
1 = off
1 = off
1 = off
1 = off
**Unused bits should be set to 0.
**Refer to Table 14 the signals that are blocked on pins CNTL0-2.
Bit 0 0 = Address A[7:0] inputs to the PLD AND array are connected.
1 = Address A[7:0] inputs to the PLD AND array are disconnected, saving power.
Note: In 80C51 mode, A[7:1] comes from Port F (PF1-PF3) and AD10 [3:0].
Bit 2 0 = Cntl0 input to the PLD AND array is connected.
1 = Cntl0 input to PLD AND array is disconnected, saving power.
Bit 3 0 = Cntl1 input to the PLD AND array is connected.
1 = Cntl1 input to PLD AND array is disconnected, saving power.
Bit 4 0 = Cntl2 input to the PLD AND array is connected.
1 = Cntl2 input to PLD AND array is disconnected, saving power.
Bit 5 0 = ALE input to the PLD AND array is connected.
1 = ALE input to PLD AND array is disconnected, saving power.
Bit 6 0 = DBE input to the PLD AND array is connected.
1 = DBE input to PLD AND array is disconnected, saving power.
67
PSD8XX Family
PSD835G2
The
Table 28. APD Counter Operation
APD ALE
PSD835G2
Functional
Blocks
(cont.)
Enable Bit PD Polarity ALE Level
APD Counter
0
1
1
1
X
X
1
0
X
Not Counting
Not Counting
Pulsing
1
0
Counting (Generates PDN after 15 Clocks)
Counting (Generates PDN after 15 Clocks)
9.5.2 Other Power Saving Options
The PSD835G2 offers other reduced power saving options that are independent of the
Power Down Mode. Except for the SRAM Standby and CSI input features, they are
enabled by setting bits in the PMMR0 and PMMR2 registers.
9.5.2.1 Zero Power PLD
The power and speed of the PLDs are controlled by the Turbo bit (bit 3) in the PMMR0.
By setting the bit to “1”, the Turbo mode is disabled and the PLDs consume Zero Power
current when the inputs are not switching for an extended time of 70 ns. The propagation
delay time will be increased after the Turbo bit is set to “1” (turned off) when the inputs
change at a composite frequency of less than 15 MHz. When the Turbo bit is set to a “0”
(turned on), the PLDs run at full power and speed. The Turbo bit affects the PLD’s D.C.
power, AC power, and propagation delay. Refer to AC/DC spec for PLD timings.
Note: Blocking MCU control signals with PMMR2 bits can further reduce PLD AC power
consumption.
9.5.2.2 SRAM Standby Mode (Battery Backup)
The PSD835G2 supports a battery backup operation that retains the contents of the SRAM
in the event of a power loss. The SRAM has a Vstby pin (PE6) that can be connected to
an external battery. When V becomes lower than Vstby then the PSD will automatically
CC
connect to Vstby as a power source to the SRAM. The SRAM Standby Current (Istby) is
typically 0.5 µA. The SRAM data retention voltage is 2 V minimum. The battery-on
indicator (Vbaton) can be routed to PE7. This signal indicates when the V has dropped
CC
below the Vstby voltage and that the SRAM is running on battery power.
9.5.2.3 The CSI Input
Pin PD2 of Port D can be configured in PSDsoft as the CSI input. When low, the signal
selects and enables the internal Flash, Boot Block, SRAM, and I/O for read or write
operations involving the PSD835G2. A high on the CSI pin will disable the Flash memory,
Boot Block, and SRAM, and reduce the PSD power consumption. However, the PLD and
I/O pins remain operational when CSI is high. Note: there may be a timing penalty when
using the CSI pin depending on the speed grade of the PSD that you are using. See the
timing parameter t
in the AC/DC specs.
SLQV
9.5.2.4 Input Clock
The PSD4000 provides the option to turn off the CLKIN input to the PLD to save AC
power consumption. The CLKIN is an input to the PLD AND array and the Output
Micro Cells. During Power Down Mode, or, if the CLKIN input is not being used as part of
the PLD logic equation, the clock should be disabled to save AC power. The CLKIN will be
disconnected from the PLD AND array or the Micro Cells by setting bits 4 or 5 to a “1” in
PMMR0.
9.5.2.5 MCU Control Signals
The PSD835G2 provides the option to turn off the address input (A7-0) and input control
signals (CNTL0-2, ALE, and DBE) to the PLD to save AC power consumption. These
signals are inputs to the PLD AND array. During Power Down Mode, or, if any of them are
not being used as part of the PLD logic equation, these control signals should be disabled
to save AC power. They will be disconnected from the PLD AND array by setting bits 0, 2,
3, 4, 5, and 6 to a “1” in the PMMR2.
68
PSD835G2
PSD8XX Family
The
9.5.3 Reset and Power On Requirement
PSD835G2
Functional
Blocks
(cont.)
9.5.3.1 Power On Reset
Upon power up the PSD835G2 requires a reset pulse of tNLNH-PO (minimum 1 ms) after
is steady. During this time period the device loads internal configurations, clears
V
CC
some of the registers and sets the Flash into operating mode. After the rising edge of
reset, the PSD835G2 remains in the reset state for an additional tOPR (maximum 120 ns)
nanoseconds before the first memory access is allowed.
The PSD835G2 Flash memory is reset to the read array mode upon power up. The FSi
and CSBOOTi select signals along with the write strobe signal must be in the false
state during power-up reset for maximum security of the data contents and to remove
the possibility of data being written on the first edge of a write strobe signal. Any Flash
memory write cycle initiation is prevented automatically when V is below VLKO.
CC
9.5.3.2 Warm Reset
Once the device is up and running, the device can be reset with a much shorter pulse of
tNLNH (minimum 150 ns). The same tOPR time is needed before the device is operational
after warm reset. Figure 31 shows the timing of the power on and warm reset.
Figure 31. Power On and Warm Reset Timing
OPERATING LEVEL
t
t
NLNH
NLNH-A
t
NLNH–PO
V
CC
RESET
t
t
OPR
OPR
WARM
RESET
POWER ON RESET
9.5.3.3 I/O Pin, Register and PLD Status at Reset
Table 29 shows the I/O pin, register and PLD status during power on reset, warm reset
and power down mode. PLD outputs are always valid during warm reset, and they are
valid in power on reset once the internal PSD configuration bits are loaded. This loading of
PSD is completed typically long before the V ramps up to operating level. Once the PLD
CC
is active, the state of the outputs are determined by the equations specified in PSDsoft.
69
PSD8XX Family
PSD835G2
The
Table 29. Status During Power On Reset, Warm Reset and Power Down Mode
PSD835G2
Functional
Blocks
(cont.)
Port Configuration Power On Reset
Warm Reset
Input Mode
Valid
Power Down Mode
Unchanged
MCU I/O
Input Mode
PLD Output
Valid after internal
PSD configuration
bits are loaded
Depend on inputs to
PLD (address are
blocked in PD mode)
Address Out
Data Port
Tri-stated
Tri-stated
Tri-stated
Tri-stated
Tri-stated
Tri-stated
Not defined
Tri-stated
Tri-stated
Peripheral I/O
Register
Power On Reset
Warm Reset
Power Down Mode
PMMR0, 2
Cleared to “0”
Unchanged
Unchanged
Micro Cells Flip
Flop status
Cleared to “0” by
internal power on
reset
Depend on .re and Depend on .re and
.pr equations .pr equations
VM Register*
Initialized based on
the selection in
PSDsoft
Initialized based on Unchanged
the selection in
PSDsoft
Configuration Menu.
Configuration Menu.
All other registers
Cleared to “0”
Cleared to “0”
Unchanged
*SR_cod and Periph Mode bits in the VM Register are always cleared to zero on power on or warm reset.
**
9.5.3.4 Reset of Flash Erase and Programming Cycles
An external reset on the RESET pin will also reset the internal Flash memory state
machine. When the Flash is in programming or erase mode, the RESET pin will terminate
the programming or erase operation and return the Flash back to read mode in tNLNH-A
(minimum 25 µs) time.
9.6 Programming In-Circuit using the JTAG-ISP Interface
The JTAG-ISP interface on the PSD835G2 can be enabled on Port E (see Table 30). All
memory (Flash and Flash Boot Block), PLD logic, and PSD configuration bits may be
programmed through the JTAG-ISC interface. A blank part can be mounted on a printed
circuit board and programmed using JTAG-ISP.
The standard JTAG signals (IEEE 1149.1) are TMS, TCK, TDI, and TDO. Two additional
signals, TSTAT and TERR, are optional JTAG extensions used to speed up program and
erase operations.
By default, on a blank PSD (as shipped from factory or after erasure), four pins on Port E
are enabled for the basic JTAG signals TMS, TCK, TDI, and TDO.
See ST Application Note AN1153 for more details on JTAG In-System-Programming.
Table 30. JTAG Port Signals
Port E Pin
PE0
JTAG Signals
TMS
Description
Mode Select
Clock
PE1
TCK
PE2
TDI
Serial Data In
Serial Data Out
Status
PE3
TDO
PE4
TSTAT
TERR
PE5
Error Flag
70
PSD835G2
PSD8XX Family
9.6.1 Standard JTAG Signals
The
The standard JTAG signals (TMS, TCK, TDI, and TDO) can be enabled by any of three
different conditions that are logically ORed. When enabled, TDI, TDO, TCK, and TMS are
inputs, waiting for a serial command from an external JTAG controller device (such as
FlashLink or Automated Test Equipment). When the enabling command is received from
the external JTAG controller, TDO becomes an output and the JTAG channel is fully
functional inside the PSD. The same command that enables the JTAG channel may
optionally enable the two additional JTAG pins, TSTAT and TERR.
PSD835G2
Functional
Blocks
(cont.)
The following symbolic logic equation specifies the conditions enabling the four basic
JTAG pins (TMS, TCK, TDI, and TDO) on their respective Port E pins. For purposes of
discussion, the logic label JTAG_ON will be used. When JTAG_ON is true, the four pins
are enabled for JTAG. When JTAG_ON is false, the four pins can be used for general PSD
I/O.
JTAG_ON = PSDsoft_enabled +
/* An NVM configuration bit inside the PSD is set by the designer
in the PSDsoft Configuration utility. This dedicates the pins for
JTAG at all times (compliant with IEEE 1149.1) */
Microcontroller_enabled +
/* The microcontroller can set a bit at run-time by writing to the
PSD register, JTAG Enable. This register is located at address
CSIOP + offset C7h. Setting the JTAG_ENABLE bit in this
register will enable the pins for JTAG use. This bit is cleared
by a PSD reset or the microcontroller. See Table 31 for bit
definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT) inside the PSD can be used to
enable the JTAG pins. This PT has the reserved name
JTAGSEL. Once defined as a node in PSDabel, the designer
can write an equation for JTAGSEL. This method is used when
the Port E JTAG pins are multiplexed with other I/O signals.
It is recommended to logically tie the node JTAGSEL to the
JEN\ signal on the Flashlink cable when multiplexing JTAG
signals. See Application Note 54 for details.
Table 31. JTAG Enable Register
JTAG Enable
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
JTAG_ENABLE
*
*
*
*
*
*
*
*Bits 1-7 are not used and should set to 0.
Bit definitions:
JTAG_ENABLE 1 = JTAG Port is Enabled.
0 = JTAG Port is Disabled.
NOTE:
The state of the PSD reset input signal will not interrupt (or prevent) JTAG operations if
the JTAG pins are dedicated by an NVM configuration bit (via PSDsoft). However, the
PSD reset input will prevent or interrupt JTAG operations if the JTAG enable register is
used to enable the JTAG pins.
71
PSD8XX Family
PSD835G2
The
9.6.1 Standard JTAG Signals (cont.)
PSD835G2
Functional
Blocks
(cont.)
The PSD835G2 supports JTAG-ISP commands, but not Boundary Scan. ST's
PSDsoft software tool and FlashLink JTAG programming cable implement these JTAG-ISC
commands.
9.6.2 JTAG Extensions
TSTAT and TERR are two JTAG extension signals enabled by a JTAG command
received over the four standard JTAG pins (TMS, TCK, TDI, and TDO). They are used to
speed programming and erase functions by indicating status on PSD pins instead of
having to scan the status out serially using the standard JTAG channel. See Application
Note 54.
TERR will indicate if an error has occurred when erasing a sector or programming in
Flash memory. This signal will go low (active) when an error condition occurs, and stay
low until a special JTAG command is executed or a chip reset pulse is received after an
“ISC-DISABLE” command.
TSTAT behaves the same as the Rdy/Bsy signal described in section 9.1.1.2. TSTAT will
be high when the PSD835G2 device is in read array mode (Flash memory and Boot Block
contents can be read). TSTAT will be low when Flash memory programming or erase
cycles are in progress, and also when data is being written to the Flash Boot Block.
TSTAT and TERR can be configured as open-drain type signals with a JTAG command.
9.6.3 Security and Flash Memories Protection
When the security bit is set, the device cannot be read on a device programmer or through
the JTAG Port. When using the JTAG Port, only a full chip erase command is allowed.
All other program/erase/verify commands are blocked. Full chip erase returns the part to a
non-secured blank state. The Security Bit can be set in PSDsoft.
All Flash Memory and Boot sectors can individually be sector protected against erasures.
The sector protect bits can be set in PSDsoft.
72
PSD835G2
PSD8XX Family
10.0
Symbol
Parameter
Storage Temperature
Condition
PLDCC
Min
– 65
0
Max
Unit
°C
°C
°C
V
Absolute
Maximum
Ratings
T
+ 125
+ 70
+ 85
+ 7
STG
Commercial
Operating Temperature
Voltage on any Pin
Industrial
– 40
– 0.6
With Respect to GND
Device Programmer
Supply Voltage
V
V
With Respect to GND
With Respect to GND
– 0.6
+ 14
+ 7
V
PP
CC
Supply Voltage
ESD Protection
– 0.6
V
V
>2000
NOTE: Stresses above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operational sections of this
specification is not recommended. Exposure to Absolute Maximum Rating conditions for
extended periods of time may affect device reliability.
11.0
Operating
Range
Range
Temperature
V
Tolerance
CC
Commercial
Industrial
0° C to +70°C
–40° C to +85°C
0° C to +70°C
+ 5 V ± 10%
+ 5 V ± 10%
3.0 V to 3.6 V
3.0 V to 3.6 V
Commercial
Industrial
–40° C to +85°C
12.0
Symbol
Parameter
Condition
Min
Typ Max
Unit
Recommended
Operating
Conditions
V
V
Supply Voltage
Supply Voltage
All Speeds
4.5
5
5.5
3.6
V
CC
CC
V-Versions
All Speeds
3.0
V
73
PSD8XX Family
PSD835G2
The following tables describe the AD/DC parameters of the PSD8XX family:
AC/DC
Parameters
❏ DC Electrical Specification
❏ AC Timing Specification
• PLD Timing
– Combinatorial Timing
– Synchronous Clock Mode
– Asynchronous Clock Mode
– Input Micro Cell Timing
• Microcontroller Timing
– Read Timing
– Write Timing
– Peripheral Mode Timing
– Power Down and Reset Timing
Following are issues concerning the parameters presented:
❏ In the DC specification the supply current is given for different modes of operation.
Before calculating the total power consumption, determine the percentage of time that
the PSD8XX is in each mode. Also, the supply power is considerably different if the
Turbo bit is "OFF".
❏ The AC power component gives the PLD, Flash memory, and SRAM mA/MHz
specification. Figures 32 and 32a show the PLD mA/MHz as a function of the number
of Product Terms (PT) used.
❏ In the PLD timing parameters, add the required delay when Turbo bit is "OFF".
Figure 32. PLD I /FrequencyConsumption (V
= 5 V ± 10%)
CC
CC
110
100
90
V
CC
= 5V
80
70
60
50
40
30
20
10
0
PT 100%
PT 25%
0
5
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
74
PSD835G2
PSD8XX Family
Figure 30a. PLD ICC/Frequency Consumption (PSD835G2V Versions, VCC = 3 V)
AC/DC
Parameters
(cont.)
60
V
= 3V
CC
50
40
30
20
10
0
PT 100%
PT 25%
0
5
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
Example of PSD835G2 Typical Power Calculation at V = 5.0 V
CC
Conditions
Highest Composite PLD input frequency
(Freq PLD)
=
=
8 MHz
4 MHz
MCU ALE frequency (Freq ALE)
% Flash Access
% SRAM access
% I/O access
=
=
=
80%
15%
5% (no additional power above base)
Operational Modes
% Normal
=
=
10%
90%
% Power Down Mode
Number of product terms used
(from fitter report)
=
=
45 PT
45/193 = 23.3%
% of total product terms
Turbo Mode
=
ON
Calculation (typical numbers used)
ICC total = Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc))
= Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE
+ %SRAM x 1.5 mA/MHz x Freq ALE
+ % PLD x 2 mA/MHz x Freq PLD
+ #PT x 400 µA/PT
= 50 µA x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz
+ 0.15 x 1.5 mA/MHz x 4 MHz
+2 mA/MHz x 8 MHz
+ 45 x 0.4 mA/PT)
= 45 µA + 0.1 x (8 + 0.9 + 16 + 18 mA)
= 45 µA + 0.1 x 42.9
= 45 µA + 4.29 mA
= 4.34 mA
This is the operating power with no Flash writes or erases. Calculation is based
on IOUT = 0 mA.
75
PSD8XX Family
PSD835G2
AC/DC
Example of Typical Power Calculation at V = 5.0 V in Turbo Off Mode
CC
Parameters
(cont.)
Conditions
Highest Composite PLD input frequency
(Freq PLD)
=
=
8 MHz
4 MHz
MCU ALE frequency (Freq ALE)
% Flash Access
% SRAM access
% I/O access
=
=
=
80%
15%
5% (no additional power above base)
Operational Modes
% Normal
=
=
10%
90%
% Power Down Mode
Number of product terms used
(from fitter report)
=
=
45 PT
45/193 = 23.3%
% of total product terms
Turbo Mode
=
Off
Calculation (typical numbers used)
ICC total = Ipwrdown x %pwrdown + %normal x (ICC (ac) + ICC (dc))
= Ipwrdown x %pwrdown + % normal x (%flash x 2.5 mA/MHz x Freq ALE
+ %SRAM x 1.5 mA/MHz x Freq ALE
+ % PLD x (from graph using Freq PLD))
= 50 µA x 0.90 + 0.1 x (0.8 x 2.5 mA/MHz x 4 MHz
+ 0.15 x 1.5 mA/MHz x 4 MHz
+ 24 mA)
= 45 µA + 0.1 x (8 + 0.9 + 24)
= 45 µA + 0.1 x 32.9
= 45 µA + 3.29 mA
= 3.34 mA
This is the operating power with no Flash writes or erases. Calculation is based
on IOUT = 0 mA.
76
PSD835G2
PSD8XX Family
PSD835G2 DC Characteristics (5 V ± 10% Versions)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VCC
VIH
Supply Voltage
All Speeds
4.5
5
5.5
VCC +.5
0.8
V
V
V
V
V
V
V
V
High Level Input Voltage
4.5 V < VCC < 5.5 V
4.5 V < VCC < 5.5 V
(Note 1)
2
–.5
VIL
Low Level Input Voltage
VIH1
VIL1
VHYS
VLKO
Reset High Level Input Voltage
Reset Low Level Input Voltage
Reset Pin Hysteresis
.8 VCC
–.5
VCC +.5
.2 VCC –.1
(Note 1)
0.3
VCC Min for Flash Erase and Program
2.5
4.2
0.1
I
OL = 20 µA, VCC = 4.5 V
IOL = 8 mA, VCC = 4.5 V
OH = –20 µA, VCC = 4.5 V
0.01
Output Low Voltage
VOL
0.25
4.49
0.45
V
V
I
4.4
VOH
Output High Voltage Except VSTBY On
IOH = –2 mA, VCC = 4.5 V
IOH1 = –1 µA
2.4
VSBY – 0.8
2.0
3.9
V
V
VOH
Output High Voltage VSTBY On
SRAM Standby Voltage
1
VSBY
ISBY
IIDLE
VDF
VCC
1
V
SRAM Standby Current (VSTBY Pin)
Idle Current (VSTBY Pin)
VCC = 0 V
0.5
µA
µA
V
VCC > VSBY
Only on VSTBY
–0.1
2
0.1
SRAM Data Retention Voltage
Standby Supply Current for Power
Down Mode
CSI > VCC –0.3 V
(Notes 2, 3 and 5)
ISB
100
200
µA
ILI
Input Leakage Current
Output Leakage Current
VSS < VIN < VCC
0.45 < VIN < VCC
–1
±.1
±5
1
µA
µA
ILO
–10
10
Refer to IOL and IOH in
the VOL and VOH row
IO
Output Current
PLD_TURBO = OFF,
f = 0 MHz (Note 3)
0
mA
µA/PT
mA
PLD Only
PLD_TURBO = ON,
f = 0 MHz
400
15
700
30
ICC (DC)
(Note 5)
Operating Supply
Current
During Flash Write/Erase
Only
Flash
Read Only, f = 0 MHz
f = 0 MHz
0
0
0
0
mA
mA
SRAM
Fig. 32
(Note 4)
PLD AC Base
ICC (AC)
(Note 5)
FLASH AC Adder
SRAM AC Adder
2.5
1.5
3.5
3.0
mA/MHz
mA/MHz
NOTE: 1. Reset input has hysteresis. VIL1 is valid at or below .2VCC –.1. VIH1 is valid at or above .8VCC
2. CSI deselected or internal Power Down mode is active.
3. PLD is in non-turbo mode and none of the inputs are switching
4. Refer to Figure 32 for PLD current calculation.
.
5. IO = 0 mA
77
PSD8XX Family
PSD835G2
PSD835G2 AC/DC Parameters – GPLD Timing Parameters
(5 V ± 10% Versions)
GPLD Combinatorial Timing (5 V ± 10%)
-70
-90
Slew
PT
Conditions Min Max Min Max Aloc
TURBO Rate
OFF (Note 1) Unit
Symbol
tPD
Parameter
GPLD Input Pin/Feedback to
GPLD Combinatorial Output
20
21
21
21
25
26
26
26
Add 2 Add 12 Sub 2
ns
ns
ns
ns
ns
ns
tEA
GPLD Input to GPLD
Output Enable
Add 12 Sub 2
Add 12 Sub 2
Add 12 Sub 2
Add 12
tER
GPLD Input to GPLD
Output Disable
tARP
tARPW
GPLD Register Clear or
Preset Delay
GPLD Register Clear or
Preset Pulse Width
10
20
Any
Micro Cell
tARD
GPLD Array Delay
11
16
Add 2
NOTE: 1. Fast Slew Rate output available on Port C and F.
GPLD Micro Cell Synchronous Clock Mode Timing (5 V ± 10% Versions)
-70 -90
Slew
PT TURBO Rate
Symbol
Parameter
Conditions
Min Max Min Max Aloc
OFF (Note 1) Unit
Maximum Frequency
External Feedback
1/(tS +tCO
)
34.4
52.6
83.3
30.30
43.48
50.00
MHz
Maximum Frequency
Internal Feedback
fMAX
1/(tS +tCO–10)
MHz
MHz
(fCNT
)
Maximum Frequency
Pipelined Data
1/(tCH +tCL
)
tS
Input Setup Time
Input Hold Time
14
0
15
0
Add 2 Add 12
ns
ns
ns
ns
ns
ns
ns
tH
tCH
tCL
tCO
tARD
tMIN
Clock High Time
Clock Low Time
Clock Input
Clock Input
Clock Input
6
10
10
6
Clock to Output Delay
GPLD Array Delay
15
11
18
Sub 2
Any Micro Cell
16 Add 2
Minimum Clock Period tCH+tCL (Note 2)
12
20
NOTES: 1. Fast Slew Rate output available on Port C and F.
2. CLKIN tCLCL = tCH + tCL
.
78
PSD835G2
PSD8XX Family
PSD835G2 AC/DC Parameters – GPLD Timing Parameters
(5 V ± 10% Versions)
GPLD Micro Cell Asynchronous Clock Mode Timing (5 V ± 10% Versions)
-70
-90
PT TURBO Slew
Symbol
Parameter
Conditions
1/(tSA+tCOA
Min Max Min Max Aloc
OFF
Rate Unit
Maximum Frequency
External Feedback
)
38.4
62.5
47.6
26.32
35.71
37.03
MHz
Maximum Frequency
Internal Feedback
fMAXA
1/(tSA+tCOA–10)
MHz
MHz
(fCNTA
)
Maximum Frequency
Pipelined Data
1/(tCH A+tCLA
)
tSA
Input Setup Time
6
7
8
Add 2 Add 12
ns
ns
ns
ns
tHA
Input Hold Time
12
12
15
tCHA
tCLA
tCOA
tARDA
tMINA
Clock Input High Time
Clock Input Low Time
Clock to Output Delay
GPLD Array Delay
Minimum Clock Period
9
Add 12
Add 12
12
21
11
30
Add 12 Sub 2
ns
ns
ns
Any Micro Cell
1/fCNTA
16 Add 2
16
28
Input Micro Cell Timing (5 V ± 10% Versions)
-70
-90
PT TURBO
Min Max Min Max Aloc OFF
Symbol
Parameter
Conditions
Unit
tIS
Input Setup Time
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
0
15
9
0
ns
tIH
Input Hold Time
20
12
12
Add 12 ns
tINH
tINL
tINO
NIB Input High Time
NIB Input Low Time
NIB Input to Combinatorial Delay
ns
ns
9
34
46 Add 2 Add 12 ns
NOTE: 1. Inputs from Port A, B, and C relative to register/latch clock from the PLD. ALE latch timings refer to tAVLX and tLXAX
.
79
PSD8XX Family
PSD835G2
AC Symbols for PLD Timing.
Microcontroller
Interface –
AC/DC
Parameters
(5V ± 10% Versions)
Example: tAVLX – Time from Address Valid to ALE Invalid.
Signal Letters
A – Address Input
C – CEout Output
D – Input Data
E – E Input
I
– Interrupt Input
L – ALE Input
N – Reset Input or Output
P – Port Signal Output
R – UDS, LDS, DS, RD, PSEN Inputs
S – Chip Select Input
T – R/W Input
W – WR Input
B – Vstby Output
M – Output Micro Cell
Signal Behavior
t
– Time
L
H
V
X
Z
– Logic Level Low or ALE
– Logic Level High
– Valid
– No Longer a Valid Logic Level
– Float
PW – Pulse Width
80
PSD835G2
PSD8XX Family
Microcontroller Interface – PSD835G2 AC/DC Parameters
(5V ± 10% Versions)
Read Timing (5 V ± 10% Versions)
-70
-90
Turbo
Off
Symbol
tLVLX
Parameter
Conditions
Min Max Min Max
Unit
ns
ALE or AS Pulse Width
Address Setup Time
Address Hold Time
Address Valid to Data Valid
CS Valid to Data Valid
RD to Data Valid
15
4
20
6
tAVLX
tLXAX
tAVQV
tSLQV
(Note 3)
(Note 3)
(Note 3)
ns
7
8
ns
70
75
24
90
100
32
Add 12 ns
ns
ns
(Note 5)
(Note 2)
tRLQV
RD or PSEN to Data Valid,
80C51 Mode
31
38
ns
tRHQX
tRLRH
tRHQZ
tEHEL
tTHEH
tELTL
RD Data Hold Time
RD Pulse Width
(Note 1)
(Note 1)
(Note 1)
0
0
ns
ns
ns
ns
ns
ns
27
32
RD to Data High-Z
20
25
E Pulse Width
27
6
32
10
0
R/W Setup Time to Enable
R/W Hold Time After Enable
0
Address Input Valid to Address
Output Delay
tAVPV
(Note 4)
20
25
ns
NOTES: 1. RD timing has the same timing as DS and PSEN signals.
2. RD and PSEN have the same timing.
3. Any input used to select an internal PSD835G2 function.
4. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port.
5. RD timing has the same timing as DS.
81
PSD8XX Family
PSD835G2
Microcontroller Interface – PSD835G2 AC/DC Parameters
(5V ± 10% Versions)
Write Timing (5 V ± 10% Versions)
-70
-90
Symbol
tLVLX
Parameter
ALE or AS Pulse Width
Address Setup Time
Address Hold Time
Conditions
Min Max Min Max Unit
15
4
20
6
tAVLX
(Note 1)
(Note 1)
ns
ns
tLXAX
7
8
Address Valid to Leading
Edge of WR
tAVWL
(Notes 1 and 3)
8
15
ns
tSLWL
CS Valid to Leading Edge of WR
WR Data Setup Time
WR Data Hold Time
(Note 3)
(Note 3)
12
25
4
15
35
5
ns
ns
ns
ns
tDVWH
tWHDX
tWLWH
(Notes 3 and 7)
(Note 3)
WR Pulse Width
28
35
Trailing Edge of WR to Address
Invalid
tWHAX1
tWHAX2
tWHPV
tWLMV
(Note 3)
(Note 3 and 6)
(Note 3)
6
0
8
0
ns
ns
ns
ns
Trailing Edge of WR to DPLD
Address Input Invalid
Trailing Edge of WR to Port Output
Valid Using I/O Port Data Register
27
48
30
55
WR Valid to Port Output Valid Using
Micro Cell Register Preset/Clear
(Notes 3 and 4)
Data Valid to Port Output Valid
Using Micro Cell Register
Preset/Clear
tDVMV
(Notes 3 and 5)
(Note 2)
42
20
55
25
ns
ns
Address Input Valid to Address
Output Delay
tAVPV
NOTES: 1. Any input used to select an internal PSD8XX function.
2. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port.
3. WR timing has the same timing as E and DS signals.
4. Assuming data is stable before active write signal.
5. Assuming write is active before data becomes valid.
6.
7.
t
t
WHAX2 is Address Hold Time for DPLD inputs that are used to generate chip selects for internal PSD memory.
WHDX is 6ns when writing to the Output Micro Cell Registers AB and BC.
82
PSD835G2
PSD8XX Family
Microcontroller Interface – PSD835G2 AC/DC Parameters
(5V ± 10% Versions)
Port F Peripheral Data Mode Read Timing (5 V ± 10%)
-70
-90
Turbo
Off
Symbol
Parameter
Conditions
Min Max Min Max
Unit
tAVQV (PF)
tSLQV (PF)
Address Valid to Data Valid
CSI Valid to Data Valid
RD to Data Valid
(Note 3)
30
25
21
31
22
35
35
32
38
30
Add 12
Add 12
ns
ns
ns
ns
ns
ns
ns
ns
(Notes 1 and 4)
tRLQV (PF)
RD to Data Valid 8031 Mode
Data In to Data Out Valid
RD Data Hold Time
tDVQV (PF)
tQXRH (PF)
tRLRH (PF)
tRHQZ (PF)
0
0
RD Pulse Width
(Note 1)
(Note 1)
27
32
RD to Data High-Z
23
25
Port F Peripheral Data Mode Write Timing (5 V ± 10%)
-70
-90
Symbol
Parameter
Conditions
Min Max Min Max Unit
tWLQV (PF)
tDVQV (PF)
tWHQZ (PF)
WR to Data Propagation Delay
Data to Port F Data Propagation Delay
WR Invalid to Port F Tri-state
(Note 2)
(Note 5)
(Note 2)
25
22
20
35
30
25
ns
ns
ns
NOTES: 1. RD timing has the same timing as DS and PSEN signals.
2. WR timing has the same timing as E and DS signals.
3. Any input used to select Port F Data Peripheral Mode.
4. Data is already stable on Port F.
5. Data stable on ADIO pins to data on Port F.
83
PSD8XX Family
PSD835G2
Microcontroller Interface – PSD835G2 AC/DC Parameters
(5V ± 10% Versions)
Power Down Timing (5 V ± 10%)
-70
-90
Symbol
Parameter
Conditions
Min Max
Min Max Unit
ALE Access Time from
Power Down
tLVDV
80
90
ns
µs
Maximum Delay from APD Enable
to Internal PDN Valid Signal
Using CLKIN Input
15 * tCLCL (µs) (Note 1)
tCLWH
NOTE: 1. tCLCL is the CLKIN clock period.
V
stbyon
Timing (5 V ± 10%)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tBVBH
Vstby Detection to Vstbyon Output High
(Note 1)
20
µs
V
Off Detection to V
stbyon
stby
Output Low
tBXBL
(Note 1)
20
µs
NOTE: 1. Vstbyon is measured at VCC ramp rate of 2 ms.
Reset Pin Timing (5 V ± 10%)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tNLNH
Warm RESET Active Low Time (Note 1)
RESET High to Operational Device
Power On Reset Active Low Time
150
ns
ns
tOPR
120
tNLNH-PO
1
ms
Warm RESET Active Low Time
(Note 2)
tNLNH-A
25
µs
NOTE: 1. RESET will not abort Flash programming/erase cycles.
2. RESET will abort Flash programming or erase cycle.
84
PSD835G2
PSD8XX Family
Microcontroller Interface – PSD835G2 AC/DC Parameters
(5V ± 10% Versions)
Flash Program, Write and Erase Times (5 V ± 10%)
Symbol
Parameter
Flash Program
Min
Typ
Max
Unit
8.5
3
sec
sec
sec
sec
sec
µs
Flash Bulk Erase (Preprogrammed to 00) (Note 1)
Flash Bulk Erase
30
30
10
1
tWHQV3
tWHQV2
tWHQV1
Sector Erase (Preprogrammed to 00)
Sector Erase
2.2
14
Word Program
1200
Program/Erase Cycles (Per Sector)
Sector Erase Time-Out
100,000
cycles
µs
tWHWLO
tQ7VQV
100
DQ7 Valid to Output Valid
(Data Polling) (Note 2)
30
ns
NOTE: 1. Programmed to all zeros before erase.
2. The polling status DQ7 is valid tQ7VQV ns before the data DQ0-7 is valid for reading.
ISC Timing (5 V ± 10%)
-70
-90
Symbol
Parameter
Conditions
Min Max
Min Max Unit
tISCCF
TCK Clock Frequency (except for PLD)
TCK Clock High Time
(Note 1)
(Note 1)
(Note 1)
(Note 2)
(Note 2)
(Note 2)
20
18
MHz
ns
tISCCH
23
23
2
26
26
tISCCL
TCK Clock Low Time
ns
tISCCF-P
tISCCH-P
tISCCL-P
tISCPSU
tISCPH
TCK Clock Frequency (for PLD only)
TCK Clock High Time(for PLD only)
TCK Clock Low Time(for PLD only)
ISC Port Set Up Time
2
MHz
ns
240
240
6
240
240
8
ns
ns
ISC Port Hold Up Time
5
5
ns
tISCPCO
tISCPZV
ISC Port Clock to Output
21
21
23
23
ns
ISC Port High-Impedance to Valid Output
ns
ISC Port Valid Output to
High-Impedance
tISCPVZ
21
23
ns
NOTES: 1. For “non-PLD” programming, erase or in ISC by-pass mode.
2. For program or erase PLD only.
85
PSD8XX Family
PSD835G2
PSD835G2 DC Characteristics (3.0 V to 3.6 V Versions) Advance Information
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VCC
VIH
Supply Voltage
All Speeds
3.0
.7 VCC
–.5
3.6
VCC +.5
0.8
V
V
V
V
V
V
V
V
High Level Input Voltage
3.0 V < VCC < 3.6 V
3.0 V < VCC < 3.6 V
(Note 1)
VIL
Low Level Input Voltage
VIH1
VIL1
VHYS
VLKO
Reset High Level Input Voltage
Reset Low Level Input Voltage
Reset Pin Hysteresis
.8 VCC
–.5
VCC +.5
.2 VCC –.1
(Note 1)
0.3
VCC Min for Flash Erase and Program
1.5
2.3
0.1
I
OL = 20 µA, VCC = 3.0 V
IOL = 4 mA, VCC = 3.0 V
OH = –20 µA, VCC = 3.0 V
0.01
Output Low Voltage
VOL
0.15
2.99
0.45
V
V
I
2.9
VOH
Output High Voltage Except VSTBY On
IOH = –1 mA, VCC = 3.0 V
IOH1 = 1 µA
2.7
VSBY – 0.8
2.0
2.8
V
V
VOH
Output High Voltage VSTBY On
SRAM Standby Voltage
1
VSBY
ISBY
IIDLE
VDF
VCC
1
V
SRAM Standby Current (VSTBY Pin)
Idle Current (VSTBY Pin)
VCC = 0 V
0.5
µA
µA
V
VCC > VSBY
Only on VSTBY
–0.1
2
0.1
SRAM Data Retention Voltage
Standby Supply Current
for Power Down Mode
CSI >VCC –0.3 V
(Notes 2 and 3)
ISB
50
100
µA
ILI
Input Leakage Current
Output Leakage Current
VSS < VIN < VCC
0.45 < VIN < VCC
–1
±.1
±5
1
µA
µA
ILO
–10
10
Refer to IOL and IOH in
the VOL and VOH row
IO
Output Current
ZPLD_TURBO = OFF,
f = 0 MHz (Note 3)
0
mA
µA/PT
mA
PLD Only
ZPLD_TURBO = ON,
f = 0 MHz
200
10
400
25
ICC (DC)
(Note 5)
Operating
Supply Current
FLASH
During FLASH
Write/Erase Only
Read Only, f = 0 MHz
f = 0 MHz
0
0
0
0
mA
mA
SRAM
PLD AC Base
(Note 4)
Figure 32a
I
CC (AC)
FLASH
(Note 5)
AC Adder
1.5
0.8
2.0
1.5
mA/MHz
mA/MHz
SRAM AC Adder
NOTES: 1. Reset input has hysteresis. VIL1 is valid at or below .2VCC –.1. VIH1 is valid at or above .8VCC
2. CSI deselected or internal PD mode is active.
.
3. PLD is in non-turbo mode and none of the inputs are switching.
4. Refer to Figure 31a for PLD current calculation.
5. IO = 0 mA.
86
PSD835G2
PSD8XX Family
PSD835G2 AC/DC Parameters – CPLD Timing Parameters
(3.0 V to 3.6 V Versions)
GPLD Combinatorial Timing (3.0 V to 3.6 V Versions)
-90
-12
Slew
PT
Min Max Min Max Aloc
TURBO Rate
Symbol
Parameter
Conditions
OFF (Note 1) Unit
GPLD Input Pin/Feedback to
GPLD Combinatorial Output
tPD
38
43
43
38
43 Add 4 Add 20 Sub 6 ns
GPLD Input to GPLD Output
Enable
tEA
45
45
43
Add 20 Sub 6 ns
Add 20 Sub 6 ns
Add 20 Sub 6 ns
GPLD Input to GPLD Output
Disable
tER
GPLD Register Clear or
Preset Delay
tARP
GPLD Register Clear or
Preset Pulse Width
tARPW
tARD
28
30
Add 20
ns
ns
GPLD Array Delay
Any Micro Cell
23
27 Add 4
NOTE: 1. Fast Slew Rate output available on Port C and F.
GPLD Micro Cell Synchronous Clock Mode Timing (3.0 V to 3.6 V Versions)
-90 -12
Slew
TURBO Rate
OFF (Note 1) Unit
PT
Min Max Min Max Aloc
Symbol
Parameter
Conditions
Maximum Frequency
External Feedback
1/(tS +tCO
)
24.3
32.2
45.0
20.4
25.6
35.7
MHz
Maximum Frequency
Internal Feedback (fCNT
fMAX
1/(tS +tCO–10)
MHz
MHz
)
Maximum Frequency
Pipelined Data
1/(tCH+tCL
)
tS
Input Setup Time
Input Hold Time
18
0
23
0
Add 4 Add 20
ns
tH
ns
tCH
tCL
tCO
tARD
tMIN
Clock High Time
Clock Input
Clock Input
11
11
14
14
ns
Clock Low Time
ns
Sub 6 ns
ns
Clock to Output Delay
GPLD Array Delay
Minimum Clock Period
Clock Input
23
23
26
Any Micro Cell
27 Add 4
tCH+tCL(Note 2) 22
28
ns
NOTES: 1. Fast Slew Rate output available on Port C and F.
2. CLKIN tCLCL = tCH + tCL
.
87
PSD8XX Family
PSD835G2
PSD835G2 AC/DC Parameters – GPLD Timing Parameters
(3.0 V to 3.6 V Versions)
GPLD Micro Cell Asynchronous Clock Mode Timing (3.0 V to 3.6 V Versions)
-90
-12
PT
Min Max Min Max Aloc
TURBO Slew
Symbol
Parameter
Conditions
OFF
Rate Unit
Maximum Frequency
External Feedback
1/(tSA+tCOA
)
23.8
31.25
38.4
20.8
26.3
30.3
MHz
Maximum Frequency
Internal Feedback (fCNTA
1/(tSA+tCOA–10)
1/(tCH A+tCLA
fMAXA
MHz
MHz
)
Maximum Frequency
Pipelined Data
)
tSA
Input Setup Time
Input Hold Time
8
10
12
18
15
Add 4 Add 20
ns
ns
ns
ns
tHA
10
15
12
tCHA
tCLA
tCOA
tARD
tMINA
Clock High Time
Add 20
Add 20
Clock Low Time
Clock to Output Delay
GPLD Array Delay
Minimum Clock Period
34
23
38
Add 20 Sub 6 ns
Any Micro Cell
1/fCNTA
27 Add 4
ns
ns
32
38
Input Micro Cell Timing (3.0 V to 3.6 V Versions)
-90
-12
PT
TURBO
Symbol
Parameter
Conditions
Min Max Min Max
Aloc
OFF
Unit
tIS
Input Setup Time
Input Hold Time
(Note 1)
(Note 1)
(Note 1)
(Note 1)
0
0
ns
ns
ns
ns
tIH
20
13
12
23
13
13
Add 20
tINH
tINL
NIB Input High Time
NIB Input Low Time
NIB Input to Combinatorial
Delay
tINO
(Note 1)
46
62
Add 4
Add 20
ns
NOTE: 1. Inputs from Port A, B, and C relative to register/latch clock from the PLD. ALE latch timings refer to tAVLX and tLXAX
.
88
PSD835G2
PSD8XX Family
AC Symbols for PLD Timing.
Microcontroller
Interface –
PSD835G2
AC/DC
Example: tAVLX – Time from Address Valid to ALE Invalid.
Signal Letters
Parameters
(3.0 V to 3.6 V
Versions)
A – Address Input
C – CEout Output
D – Input Data
E – E Input
G – Internal WDOG_ON signal
I
– Interrupt Input
L – ALE Input
N – Reset Input or Output
P – Port Signal Output
Q – Output Data
R – WR, UDS, LDS, DS, IORD, PSEN Inputs
S – Chip Select Input
T – R/W Input
W – Internal PDN Signal
B – Vstby Output
M – Output Micro Cell
Signal Behavior
t
– Time
L
H
V
X
Z
– Logic Level Low or ALE
– Logic Level High
– Valid
– No Longer a Valid Logic Level
– Float
PW – Pulse Width
89
PSD8XX Family
PSD835G2
Microcontroller Interface – PSD835G2 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Read Timing (3.0 V to 3.6 V Versions)
-90
-12
Turbo
Off
Symbol
tLVLX
Parameter
Conditions
Min Max Min Max
Unit
ns
ns
ns
ns
ns
ns
ALE or AS Pulse Width
Address Setup Time
Address Hold Time
Address Valid to Data Valid
CS Valid to Data Valid
RD to Data Valid
22
7
24
9
tAVLX
tLXAX
tAVQV
tSLQV
(Note 3)
(Note 3)
(Note 3)
8
10
90
90
35
120 Add 20**
120
35
(Note 5)
(Note 2)
tRLQV
RD or PSEN to Data Valid,
80C51XA Mode
45
48
40
ns
tRHQX
tRLRH
tRHQZ
tEHEL
tTHEH
tELTL
RD Data Hold Time
RD Pulse Width
(Note 1)
(Note 1)
(Note 1)
0
0
ns
ns
ns
ns
ns
ns
36
40
RD to Data High-Z
38
E Pulse Width
38
10
0
42
16
0
R/W Setup Time to Enable
R/W Hold Time After Enable
Address Input Valid to
Address Output Delay
tAVPV
(Note 4)
30
35
ns
NOTES: 1. RD timing has the same timing as DS and PSEN signals.
2. RD and PSEN have the same timing for 80C51.
3. Any input used to select an internal PSD835G2V function.
4. In multiplexed mode latched address generated from ADIO delay to address output on any Port.
5. RD timing has the same timing as DS.
90
PSD835G2
PSD8XX Family
Microcontroller Interface – PSD835G2 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Write Timing (3.0 V to 3.6 V Versions)
-90
-12
Symbol
tLVLX
Parameter
ALE or AS Pulse Width
Address Setup Time
Address Hold Time
Conditions
Min Max Min Max Unit
22
7
24
9
tAVLX
tLXAX
(Note 1)
(Note 1)
ns
ns
8
10
Address Valid to Leading
Edge of WR
tAVWL
(Notes 1 and 3)
15
18
ns
tSLWL
CS Valid to Leading Edge of WR
WR Data Setup Time
(Note 3)
(Note 3)
15
40
5
18
45
8
ns
ns
ns
ns
ns
tDVWH
tWHDX
tWLWH
tWHAX1
WR Data Hold Time
(Notes 3 and 7)
(Note 3)
WR Pulse Width
40
8
45
10
Trailing Edge of WR to Address Invalid
(Note 3)
Trailing Edge of WR to DPLD Address
Input Invalid
tWHAX2
(Notes 3 and 6)
(Note 3)
0
0
ns
ns
ns
ns
ns
Trailing Edge of WR to Port Output
Valid Using I/O Port Data Register
tWHPV
tWLMV
tDVMV
tAVPV
33
65
65
30
33
70
68
35
WR Valid to Port Output Valid Using
Micro Cell Register Preset/Clear
(Notes 3 and 4)
(Notes 3 and 5)
(Note 2)
Data Valid to Port Output Valid
Using Micro Cell Register Preset/Clear
Address Input Valid to Address
Output Delay
NOTES: 1. Any input used to select an internal PSD835G2 function.
2. In multiplexed mode, latched addresses generated from ADIO delay to address output on any Port.
3. WR timing has the same timing as E and DS signals.
4. Assuming data is stable before active write signal.
5. Assuming write is active before data becomes valid.
6. tWHAX2 is Address hold time for DPLD inputs that are used to generate chip selects for internal PSD memory.
7. tWHDX is 11ns when writing to the Output Micro Cell Registers AB and BC.
91
PSD8XX Family
PSD835G2
Microcontroller Interface – PSD835G2 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Port F Peripheral Data Mode Read Timing (3.0 V to 3.6 V Versions)
-90
-12
Turbo
Off
Symbol
Parameter
Conditions
(Note 3)
Min Max Min Max
Unit
tAVQV (PF)
tSLQV (PF)
Address Valid to Data Valid
CSI Valid to Data Valid
RD to Data Valid
50
35
35
45
34
50 Add 20 ns
40 Add 20 ns
(Notes 1 and 4)
40
45
38
ns
ns
ns
ns
ns
ns
tRLQV (PF)
RD to Data Valid, 8031 Mode
Data In to Data Out Valid
RD Data Hold Time
tDVQV (PF)
tQXRH (PF)
tRLRH (PF)
tRHQZ (PF)
0
0
RD Pulse Width
(Note 1)
(Note 1)
35
36
RD to Data High-Z
38
40
Port F Peripheral Data Mode Write Timing (3.0 V to 3.6 V Versions)
-90
-12
Symbol
Parameter
Conditions
(Note 2)
Min Max Min Max Unit
tWLQV (PF)
WR to Data Propagation Delay
40
35
33
43
38
33
ns
ns
ns
Data to Port F Data Propagation
Delay
(Note 5)
(Note 2)
tDVQV (PF)
tWHQZ (PF)
WR Invalid to Port F Tri-state
NOTES: 1. RD timing has the same timing as DS and PSEN signals.
2. WR timing has the same timing as E and DS signals.
3. Any input used to select Port F Data Peripheral Mode.
4. Data is already stable on Port F.
5. Data stable on ADIO pins to data on Port F.
92
PSD835G2
PSD8XX Family
Microcontroller Interface – PSD835G2 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Power Down Timing (3.0 V to 3.6 V Versions)
-90
-12
Symbol
Parameter
Conditions
Min Max
Min Max Unit
ALE Access Time from
Power Down
tLVDV
128
135
ns
µs
Maximum Delay from APD Enable
to Internal PDN Valid Signal
tCLWH
Using CLKIN Input
15 tCLCL (µs) (Note 1)
*
NOTE: 1. tCLCL is the CLKIN clock period.
V
stbyon
Timing (3.0 V to 3.6 V Versions)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tBVBH
V
Detection to V
stbyon
Output
stby
(Note 1)
20
µs
High
tBXBL
V
Off Detection to V
stbyon
stby
(Note 1)
20
µs
Output Low
NOTE: 1. Vstbyon is measured at VCC ramp rate of 2 ms.
Reset Pin Timing (3.0 V to 3.6 V Versions)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tNLNH
Warm RESET Active Low Time (Note 1)
RESET High to Operational Device
Power On Reset Active Low Time
300
ns
ns
tOPR
300
tNLNH-PO
1
ms
Warm RESETActive Low Time
(Note 2)
tNLNH-A
25
µs
NOTE: 1. RESET will not abort Flash programming/erase cycles.
2. RESET will abort Flash programming or erase cycle.
93
PSD8XX Family
PSD835G2
Microcontroller Interface – PSD835G2 AC/DC Parameters
(3.0 V to 3.6 V Versions)
Flash Program, Write and Erase Times (3.0 V to 3.6 V Versions)
Symbol
Parameter
Flash Program
Min
Typ
Max
Unit
8.5
3
sec
sec
sec
sec
sec
µs
Flash Bulk Erase (Preprogrammed to 00) (Note 1)
Flash Bulk Erase
30
30
10
1
tWHQV3
tWHQV2
tWHQV1
Sector Erase (Preprogrammed to 00)
Sector Erase
2.2
14
Word Program
1200
Program/Erase Cycles (Per Sector)
Sector Erase Time-Out
100,000
cycles
µs
tWHWLO
tQ7VQV
100
DQ7 Valid to Output Valid (Data Polling)
(Note 2)
30
ns
NOTES: 1. Programmed to all zeros before erase.
2. The polling status DQ7 is valid tQ7VQV ns before the data DQ0-7 is valid for reading.
ISC Timing (3.0 V to 3.6 V Versions)
-90
-12
Symbol
Parameter
Conditions
Min Max
Min Max Unit
tISCCF
TCK Clock Frequency (except for PLD)
TCK Clock High Time
(Note 1)
(Note 1)
(Note 1)
(Note 2)
(Note 2)
(Note 2)
15
12
MHz
ns
tISCCH
30
30
2
40
40
tISCCL
TCK Clock Low Time
ns
tISCCF-P
tISCCH-P
tISCCL-P
tISCPSU
tISCPH
TCK Clock Frequency (for PLD only)
TCK Clock High Time (for PLD only)
TCK Clock Low Time (for PLD only)
ISC Port Set Up Time
2
MHz
ns
240
240
11
5
240
240
12
ns
ns
ISC Port Hold Up Time
5
ns
tISCPCO
tISCPZV
tISCPVZ
ISC Port Clock to Output
26
26
26
32
32
32
ns
ISC Port High-Impedance to Valid Output
ISC Port Valid Output to High-Impedance
ns
ns
NOTES: 1. For “non-PLD” programming, erase or in ISC by-pass mode.
2. For program or erase PLD only.
94
PSD835G2
PSD8XX Family
Figure 33. Read Timing
t
t
AVLX
LXAX*
ALE/AS
t
LVLX
A/D
MULTIPLEXED
BUS
ADDRESS
VALID
DATA
VALID
t
AVQV
ADDRESS
NON-MULTIPLEXED
BUS
ADDRESS
VALID
DATA
NON-MULTIPLEXED
BUS
DATA
VALID
t
SLQV
CSI
t
t
RLQV
t
RHQX
RLRH
RD
(PSEN, DS)
tRHQZ
t
EHEL
E
t
THEH
t
ELTL
R/W
t
AVPV
ADDRESS OUT
*tAVLX and tLXAX are not required 80C51XA in Burst Mode.
95
PSD8XX Family
PSD835G2
Figure 34. Write Timing
t
t
LXAX
AVLX
ALE/AS
t
LVLX
A/D
MULTIPLEXED
BUS
ADDRESS
VALID
DATA
VALID
t
AVWL
ADDRESS
NON-MULTIPLEXED
BUS
ADDRESS
VALID
DATA
NON-MULTIPLEXED
BUS
DATA
VALID
t
SLWL
CSI
t
t
DVWH
WHDX
t
WR
WLWH
t
WHAX
(DS)
t
EHEL
E
t
t
THEH
ELTL
R/ W
t
WLMV
t
t
AVPV
WHPV
STANDARD
MCU I/O OUT
ADDRESS OUT
96
PSD835G2
PSD8XX Family
Figure 35. Peripheral I/O Read Timing
ALE/AS
ADDRESS
DATA VALID
A/D BUS
t
(PF)
(PF)
AVQV
t
SLQV
CSI
RD
t
t
(PF)
(PF)
RLQV
t
t
(PF)
(PF)
QXRH
RHQZ
RLRH
t
(PF)
DVQV
DATA ON PORT A
Figure 36. Peripheral I/O Write Timing
ALE/AS
ADDRESS
DATA OUT
A/D BUS
tWHQZ (PF)
tWLQV (PF)
WR
tDVQV (PA)
PORT F
DATA OUT
97
PSD8XX Family
PSD835G2
Figure 37. Combinatorial Timing – PLD
CPLD INPUT
t
PD
CPLD
OUTPUT
Figure 38. Synchronous Clock Mode Timing – PLD
t
t
CL
CH
CLKIN
INPUT
t
S
t
H
t
CO
REGISTERED
OUTPUT
98
PSD835G2
PSD8XX Family
Figure 39. Asynchronous Clock Mode Timing (Product-Term Clock)
tCHA
tCLA
CLOCK
INPUT
tSA
tHA
tCOA
REGISTERED
OUTPUT
Figure 40. Input Micro Cell Timing (Product-Term Clock)
t
t
INL
INH
PT CLOCK
t
t
IS
IH
INPUT
OUTPUT
t
INO
99
PSD8XX Family
PSD835G2
Figure 41. Input to Output Disable /Enable
INPUT
tER
tEA
INPUT TO
OUTPUT
ENABLE/DISABLE
Figure 42. Asynchronous Reset /Preset
tARPW
RESET/PRESET
INPUT
tARP
REGISTER
OUTPUT
Figure 43. ISC Timing
tISCCH
TCK
tISCCL
tISCPSU
tISCPH
TDI/TMS
t ISCPZV
tISCPCO
ISC OUTPUTS/TDO
tISCPVZ
ISC OUTPUTS/TDO
100
PSD835G2
PSD8XX Family
Figure 44. Reset Timing
OPERATING LEVEL
t
t
NLNH
NLNH-A
t
NLNH–PO
V
CC
RESET
t
t
OPR
OPR
WARM
RESET
POWER ON RESET
Figure 45. Key to Switching Waveforms
INPUTS
OUTPUTS
WAVEFORMS
STEADY INPUT
STEADY OUTPUT
MAY CHANGE FROM
HI TO LO
WILL BE CHANGING
FROM HI TO LO
MAY CHANGE FROM
LO TO HI
WILL BE CHANGING
LO TO HI
DON'T CARE
CHANGING, STATE
UNKNOWN
OUTPUTS ONLY
CENTER LINE IS
TRI-STATE
101
PSD8XX Family
PSD835G2
TA = 25 °C, f = 1 MHz
14.0
Pin Capacitance
Symbol
Parameter1
Conditions Typical2 Max Unit
CIN
Capacitance (for input pins only)
Capacitance (for input/output pins)
VIN = 0 V
VOUT = 0 V
VPP = 0 V
4
8
6
pF
pF
pF
COUT
CVPP
12
25
Capacitance (for CNTL2/VPP
)
18
NOTES: 1. These parameters are only sampled and are not 100% tested.
2. Typical values are for TA = 25°C and nominal supply voltages.
15.0
Figure 46.
AC Testing
Input/Output
Waveform
3.0V
TEST POINT
1.5V
0V
16.0
2.01 V
Figure 47.
AC Testing
Load Circuit
195 Ω
DEVICE
UNDER TEST
CL = 30 pF
(INCLUDING
SCOPE AND JIG
CAPACITANCE)
Upon delivery from ST, the PSD835G2 device has all bits in the PLDs and
memories in the “1” or high state. The configuration bits are in the “0” or low state. The
code, configuration, and PLDs logic are loaded through the procedure of programming.
17.0
Programming
Information for programming the device is available directly from ST. Please
contact your local sales representative. (See the last page.)
102
PSD835G2
PSD8XX Family
18.0
80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U)
PSD835G2
Pin
Assignments
Pin No.
Pin Assignments
Pin No.
Pin Assignments
1
PD2
PD3
AD0
AD1
AD2
AD3
AD4
GND
VCC
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
GND
GND
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
CNTL0
CNTL1
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
VCC
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
VCC
GND
PF0
GND
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
PD0
PD1
PF1
PF2
PF3
PF4
PF5
PF6
PF7
RESET
CNTL2
103
PSD8XX Family
PSD835G2
Figure 48. Drawing U5 – 80-Pin Plastic Thin Quad Flatpack (TQFP)
(Package Type U)
19.0
PSD835G2
Package
Information
PD2
PD3
AD0
AD1
AD2
AD3
AD4
GND
1
2
3
4
5
6
7
8
9
60 CNTL1
59 CNTL0
58 PA7
57 PA6
56 PA5
55 PA4
54 PA3
53 PA2
52 PA1
51 PA0
50 GND
49 GND
48 PC7
47 PC6
46 PC5
45 PC4
44 PC3
43 PC2
42 PC1
41 PC0
V
CC
AD5 10
AD6 11
AD7 12
AD8 13
AD9 14
AD10 15
AD11 16
AD12 17
AD13 18
AD14 19
AD15 20
104
PSD835G2
PSD8XX Family
Figure 48A.
Drawing U5 – 80-Pin Plastic Thin Quad Flatpack (TQFP) (Package Type U)
D
D1
D3
80
1
2
3
Index
Mark
E
E3
E1
Standoff:
0.05 mm Min.
C
A1 A2
A
α
L
Load Coplanarity:
0.102 mm Max.
B
e1
Family: Plastic Thin Quad Flatpack (TQFP)
Millimeters
Inches
Symbol
Min
Max
Notes
Min
Max
Notes
α
0°
7°
0°
8°
A
–
1.20
1.05
–
0.047
0.041
0.011
0.008
0.551
0.472
A2
B
0.95
0.17
0.037
0.007
0.27
Reference
Reference
C
0.20
D
13.95
11.95
14.05
12.05
0.512
0.433
D1
D3
E
9.5
0.374
Reference
13.95
11.95
14.05
12.05
0.512
0.433
0.551
0.472
E1
E3
e1
L
9.5
Reference
Reference
0.374
0.019
Reference
Reference
0.50
0.45
0.75
0.018
0.030
N
80
80
060198R0
105
Selector Guide – PSD8XX Series
Part # MCU
PLDs/Decoders
I/O
Memory
Other
Software
5
Data Inputs Input Macrocells
Ports Flash Program Store
ISP via JTAG
IAP via MCU
Zero Power
Per. Mode
Security
PSDsoft
Express
Path
Volts
Output Macrocells
Outputs
2nd Flash Array
EEPROM
PSDsoft
2000
Page
Reg.
SRAM
w/BB
PMU
APD
PSD835G2
PSD813F2
PSD834F2
PSD833F2
8
8
8
8
82
73
73
73
24
24
24
24
16
16
16
16
24
19
19
19
8-bit
8-bit
8-bit
8-bit
52 4096Kb 256Kb
27 1024Kb 256Kb
27 2048Kb 256Kb
27 2048Kb 256Kb
–
–
–
–
64Kb
16Kb
64Kb
64Kb
X
X
X
X
X
X
X
X
X
–
–
–
–
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
PSD835G2
PSD8XX Family
21.0
Part Number
Construction
Flash PSD Part Number Construction
CHARACTER # 1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
PART
NUMBER
P
S
D
4 2
1
3
F
2
–
A
–
1
5
J
TEMP RANGE
"Blank" = 0°C to 70°C (Commercial)
PSD BRAND NAME
PSD = Standard Low
Power Device
+
+
I = –40°C to 85°C (Industrial)
FAMILY/SERIES
8 = Flash PSD for 8-bit MCUs
PACKAGE TYPE
J = PLCC
U = TQFP
M = PQFP
B81 = BGA
41 = Flash PSD for 16-bit MUCs
(with simple PLD)
42 = Flash PSD for 16-bit MUCs
(with CPLD)
SPEED
- 70 = 70ns
- 90 = 90ns
- 12 = 120ns
- 15 = 150ns
- 20 = 200ns
SRAM SIZE
0 = 0Kb
1 = 16Kb
2 = 32Kb
3 = 64Kb
REVISION
NVM SIZE
1 = 256Kb
2 = 512Kb
3 = 1Mb
"Blank" = no rev.
- A = Rev. A
- B = Rev. B
- C = Rev. C
4 = 2Mb
5 = 4Mb
V
VOLTAGE
cc
I/O COUNT & OTHER
F = 27 I/O
"blank" = 5 Volt
V = 3.0 Volt
G = 52 I/O
2ND NVM TYPE, SIZE
& CONFIGURATION
1 = EEPROM, 256Kb
2 = FLASH, 256Kb
3 = No 2nd Array
22.0
Ordering
Information
Operating
Temperature
Range
Speed
(ns)
Part Number
Package Type
PSD835G2-70U
PSD835G2-90U
PSD835G2-90UI
70
90
90
80 Pin TQFP
80 Pin TQFP
80 Pin TQFP
Comm’l
Comm’l
Industrial
PSD835G2V-90U
PSD835G2V-12U
PSD835G2V-12UI
90
120
120
80 Pin TQFP
80 Pin TQFP
80 Pin TQFP
Comm’l
Comm’l
Industrial
107
PSD835G2
REVISION HISTORY
Table 1. Document Revision History
Date
Rev.
Description of Revision
01-Mar-2000
1.0
PSD835G2: Document written in the WSI format. Initial release
Page 78: changed Turbo Off from add 10 to add 12,
changed tCO -70 Max from 13 to 15.
Page 79: changed Turbo Off from add 10 to add 12,
changed tHA -70 Min from 5 to 7,
changed tCLA - 70 Min from 9 to 12,
changed tCLA - 90 Min from 12 to 15.
Page 81: changed Turbo Off from add 10 to add 12,
changed tLXAX -70 Min from 5 to 7.
30-Nov-2000
1.1
Page 82: changed tLXAX -70 Min from 5 to 7,
changed tDVWH -70 Min from 12 to 25,
changed tWLWH -70 Min from 25 to 28.
Page 83: changed Turbo Off from add 10 to add 12.
PSD835G2: Configurable Memory System on a Chip for 8-Bit Microcontrollers
Front page, and back two pages, in ST format, added to the PDF file
Any references to Waferscale, WSI, EasyFLASH and PSDsoft 2000
updated to ST, ST, Flash+PSD and PSDsoft Express
31-Jan-2002
1.2
2/3
PSD835G2
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is registered trademark of STMicroelectronics
All other names are the property of their respective owners
© 2002 STMicroelectronics - All Rights Reserved
STMicroelectronics group of companies Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong -
India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
www.st.com
3/3
相关型号:
©2020 ICPDF网 联系我们和版权申明