SN751518FT [STMICROELECTRONICS]
DC PLASMA DISPLAY DRIVERS; 直流等离子显示驱动器
| 型号： | SN751518FT |
| 厂家： | 
ST |
| 描述： | DC PLASMA DISPLAY DRIVERS |
| 文件： | 总19页 (文件大小：287K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
SN751508 . . . FT PACKAGE
(TOP VIEW)
Each Device Drives 32 Lines
–120-V PNP Open-Collector Parallel
Outputs
Q32
Q31
Q30
Q29
Q28
Q27
Q26
Q25
Q24
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
1
2
3
4
5
6
7
8
9
48
47
46
45
44
43
42
41
40
High-Speed Serially Shifted Data Inputs
CMOS-Compatible Inputs
Strobe and Sustain Inputs Provided
Serial Data Output for Cascade Operation
description
Q9
The SN751508 and SN751518 are monolithic
integrated circuits designed to drive the data lines
of a dc plasma panel display. The SN751518 pin
sequence is reversed from the SN751508 for
ease in printed-circuit-board layout.
Q23 10 39
Q10
Q11
Q12
Q13
Q14
Q15
Q16
GND
SUSTAIN
NC
LATCH ENABLE
NC
11 38
12 37
13 36
14 35
15 34
16 33
17 32
18 31
19 30
20 29
21 28
22 27
23 26
24 25
Q22
Q21
Q20
Q19
Q18
Q17
GND
NC
Each device consists of two 16-bit shift registers,
32 latches, 32 OR gates, and 32 pnp open-
collector output AND gates. Typically, a 32-bit
data string is split into two 16-bit data strings
externallyandthenenteredinparallelintotheshift
registers on the high-to-low transition of the clock
signal. A high LATCH ENABLE transfers the data
fromtheshiftregisterstotheinputsof32ORgates
through the latches. Data present in the latch
during the high-to-low transition of LATCH
ENABLE is stored. When STROBE is high, the
latch is masked and a high is placed on the data
input of the output AND gates. When STROBE is
low and SUSTAIN is high, data from the latches is
reflected at the outputs. When low, SUSTAIN
forces all outputs to their off state. Drivers can be
cascaded via the serial data outputs of the static
shift registers. These outputs are not affected by
LATCH ENABLE, STROBE, or SUSTAIN.
STROBE
NC
CLOCK
V
V
CC
CC
SERIAL OUT2
SERIAL OUT1
DATA IN2
DATA IN1
SN751518 . . . FT PACKAGE
(TOP VIEW)
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q32
Q31
Q30
Q29
Q28
Q27
Q26
Q25
1
2
3
4
5
6
7
8
9
48
47
46
45
44
43
42
41
The SN751508 and the SN751518 are
characterized from 0°C to 70°C.
40 Q24
39 Q23
Q10 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
38
37
36
35
34
33
32
31
30
29
28
27
26
25
Q11
Q12
Q13
Q14
Q15
Q16
GND
Q22
Q21
Q20
Q19
Q18
Q17
GND
NC
STROBE
NC
SUSTAIN
NC
LATCH ENABLE
NC
CLOCK
V
V
CC
CC
DATA IN2
DATA IN1
SERIAL OUT2
SERIAL OUT1
NC – No internal connection
Copyright 1989, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
†
logic symbols
SN751508
CMOS/EL DISP
31
19
29
21
SUSTAIN
STROBE
LATCH ENABLE
EN44
V43
C42
CLOCK
Z40
SRG16
40(C41/→)
25
48
47
46
45
DATA IN1
Q1
Q2
Q3
Q4
41D
Z1
Z3
1
2
3
4
42D 43, 44
42D 43, 44
42D 43, 44
42D 43, 44
.
.
.
.
.
.
.
.
.
Z15
Z17
34
33
16
15
.
.
.
Q15
Q16
Q17
Q18
15 42D 43, 44
16 42D 43, 44
Z29 17 42D 43, 44
Z31 18 42D 43, 44
.
.
.
4
3
2
1
.
.
.
SRG16
40(C45/→)
26
Z2
Q29
Q30
Q31
Q32
DATA IN2
45D
29 42D 43, 44
Z4 30 42D 43, 44
31 42D 43, 44
32 42D 43, 44
Z16
.
.
.
24
23
SERIAL OUT1
SERIAL OUT2
Z18 31
.
.
.
1
Z30 32
Z32
SN751518
CMOS/EL DISP
18
30
20
28
SUSTAIN
STROBE
LATCH ENABLE
EN44
V43
C42
CLOCK
Z40
SRG16
40(C41/→)
24
1
2
3
4
.
.
.
DATA IN1
Q1
Q2
Q3
Q4
41D
Z1
Z3
1
2
3
4
42D 43, 44
42D 43, 44
42D 43, 44
42D 43, 44
.
.
.
.
.
.
Z15
Z17
15
16
33
34
.
.
.
Q15
Q16
Q17
Q18
15 42D 43, 44
16 42D 43, 44
Z29 17 42D 43, 44
Z31 18 42D 43, 44
.
.
.
45
46
47
48
.
.
.
SRG16
40(C45/→)
23
Q29
Q30
Q31
Q32
DATA IN2
45D
Z2 29 42D 43, 44
Z4 30 42D 43, 44
31 42D 43, 44
.
.
.
32 42D 43, 44
1
Z16
25
26
SERIAL OUT1
SERIAL OUT2
Z18 31
.
.
.
1
Z30 32
Z32
†
These symbols are in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
logic diagram (positive logic)
SUSTAIN
STROBE
LATCH
ENABLE
CLOCK
Shift
Latches
Register 1
DATA IN1
Q1
1D
C1
C2
2D
R1
R3
LC1
Q2
Q3
Q4
1D
C1
C2
2D
LC2
LC3
LC4
.
.
.
.
.
.
C2
2D
1D
C1
R29
R31
C2
2D
1D
C1
.
.
.
. . . . .
. . . . .
. . . . .
.
.
.
.
.
.
Shift
Register 2
DATA IN2
1D
C1
R2
Q29
Q30
Q31
Q32
C2
2D
LC29
LC30
LC31
LC32
1D
C1
R4
C2
2D
.
.
.
.
.
.
1D
C1
C2
2D
R30
R32
1D
C1
C2
2D
SERIAL
OUT1
SERIAL
OUT2
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
FUNCTION TABLE
CONTROL INPUTS
OUTPUTS
Q1 THRU Q32
LATCHES
LC1 THRU
LC32
SHIFT REGISTERS
R1 THRU R32
FUNCTION
LATCH
SERIAL
CLOCK
STROBE SUSTAIN
ENABLE
S01 S02
Determined by
LATCH
ENABLE
†
↓
X
X
X
X
X
X
Determined by
SUSTAIN and STROBE
Load and shift
No change
Load
R31 R32
R31 R32
R31 R32
No ↓
‡
Latch
Enable
X
X
L
H
X
X
X
X
As determined
above
Stored data
New data
Determined by
SUSTAIN and STROBE
Determined by
LATCH
X
X
X
X
L
H
H
H
As determined
above
LC1 thru LC32
All on (high)
Strobe
‡
ENABLE
Determined by
LATCH
ENABLE
As determined
above
Sustain
X
X
X
L
R31 R32 All off
‡
H = high level, L = low level, X = irrelevant, ↓ = high-to-low transition
†
Each even-numbered shift register stage takes on the state of the next-lower even-numbered stage, and likewise each odd-numbered shift
register stage takes on the state of the next-lower odd-numbered stage; i.e., R32 takes on the state of R30, R30 takes on the state of R28, ...
R4 takes on the state of R2, R2 takes on the state of DATA IN2, R31 takes on the state of R29, R29 takes on the state of R27, ... R3 takes on
the state of R1, and R1 takes on the state on DATA IN1.
‡
New data enters the latches while LATCH ENABLE is high. This data is stored while LATCH ENABLE is low.
typical operating sequence
. . .
CLOCK
DATA IN
Valid
Irrelevant
Valid
Shift
Register
Contents
Invalid
LATCH ENABLE
Previously Stored Data
Latch Contents
STROBE
New Data Valid
SUSTAIN
Q Outputs
Off State
Valid
Off State
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
schematics of inputs and outputs
EQUIVALENT OF EACH INPUT
TYPICAL OF ALL Q OUTPUTS
TYPICAL OF SERIAL OUTPUT
V
CC
V
CC
V
CC2
Input
Output
Output
GND
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
On-state Q output voltage range, V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.4 to 7 V
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –120 V to V
+ 0.4 V
+ 0.4 V
+ 0.4 V
O
CC
CC
CC
Input voltage range, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.4 V to V
I
Serial output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.4 V to V
Continuous total power dissipation at (or below) 25°C free-air temperature (see Note 2) . . . . . . . . 1025 mW
Operating free-air temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
A
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
NOTES: 1. Voltages values are with respect to GND.
2. For operation above 25°C free-air temperature, derate linearly to 656 mW at 70°C at the rate of 8.2 mW/°C.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
recommended operating conditions
MIN NOM
MAX
5.5
UNIT
V
Supply voltage, V
4.5
5
CC
Output voltage, V
–75
V
O
V
CC
V
CC
V
CC
V
CC
= 4.5 V
= 5.5 V
= 4.5 V
= 5.5 V
3.6
4.4
High-level input voltage, V
V
V
IH
0.9
1
Low-level input voltage, V
IL
Output current, I (T = 25°C)
–1.2
5
mA
O
A
Clock frequency, f
MHz
clock
CLOCK
75
160
90
2
DATA IN
ns
Pulse duration, t (see Figure 1)
LATCH ENABLE
w
STROBE
µs
SUSTAIN
2
DATA IN before CLOCK↓
CLOCK low before LATCH ENABLE↑
LATCH ENABLE low before CLOCK↓
LATCH ENABLE high before STROBE↓
LATCH ENABLE high before SUSTAIN↑
20
50
0
Setup time, t (see Figure 1)
su
ns
0
0
Hold time, DATA IN after CLOCK↓, t (see Figure 1)
50
0
µs
°C
h
Operating free-air temperature, T
70
A
electrical characteristics over operating free-air temperature range, V
noted)
= 5 V (unless otherwise
CC
†
PARAMETER
Q outputs
TEST CONDITIONS
= –0.5 mA
MIN TYP
MAX
UNIT
I
4
4.3
4.4
3.4
3.6
4.5
4.6
OH
I
I
I
I
I
I
I
I
= –100 µA
OH
OH
OH
OH
OL
OL
OL
OL
V
V
V
V
= 5.5 V
= 4.5 V
= 5.5 V
= 4.5 V
CC
CC
CC
CC
V
High-level output voltage
= –20 µA
= –100 µA
= –20 µA
= 100 µA
= 20 µA
= 100 µA
= 20 µA
= 3 V
V
OH
OL
SERIAL OUT 1, 2
SERIAL OUT 1, 2
3.6
0.9
0.9
1.2
1.1
1.1
0.9
V
Low-level output voltage
V
I
I
I
I
High-level Q output current
Low-level Q output current
High-level input current
Low-level input current
T = 25°C,
V
–1.2
mA
µA
µA
µA
OH
A
O
O
T = 25°C,
V
= –75 V
–500
1
OL
IH
IL
A
T = 25°C,
V = V
I CC
A
T = 25°C,
V = 0
I
–1
25
3
A
All Q outputs high,
All Q outputs low
V
CC
= 5.5 V
17
I
Supply current
mA
pF
CC
C
Input capacitance
15
i
†
All typical values are at T = 25°C.
A
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
switching characteristics, V
= 5 V, C = 15 pF, T = 25°C
L A
CC
PARAMETER
Propagation delay time, CLOCK to SERIAL OUT
TEST CONDITIONS
MIN
TYP
MAX
150
1
UNIT
ns
t
t
t
t
t
100
pd
‡
Delay time, low-to-high-level Q output from SUSTAIN or STROBE
Delay time, high-to-low-level Q output from SUSTAIN or STROBE
Transition time, low-to-high-level Q output
0.3
1
µs
DLH
DHL
TLH
THL
‡
2.5
5
µs
R
= 91 kΩ,
L
See Figures 1 and 2
2
µs
Transition time, high-to-low-level Q output
11
18
µs
‡
Typical values for delay times are measured from SUSTAIN.
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
PARAMETER MEASUREMENT INFORMATION
4 V
1 V
CLOCK
50%
t
t
w
w
t
t
h
su
4 V
1 V
DATA IN
50%
t
w
t
pd
V
V
OH
SERIAL OUT
50%
OL
t
t
su
su
t
w
4 V
1 V
LATCH
ENABLE
50%
t
t
w
su
t
w
4 V
1 V
50%
STROBE
SUSTAIN
t
t
t
w
su
w
4 V
1 V
50%
t
t
DHL
DLH
t
t
DLH
DLH
t
DLH
On
Off
90%
10%
Q Outputs
t
t
TLH
TLH
t
t
THL
TLH
t
THL
NOTE: Input t and t are less than or equal to 10 ns.
r
f
Figure 1. Input Timing and Switching Time Voltage Waveforms
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
PARAMETER MEASUREMENT INFORMATION
5 V
–75 V
15 pF
V
CC
Generator
(see Note A)
DATA IN
CLOCK
Q1
Q2
91 kΩ
Generator
(see Note A)
.
.
.
STROBE
SUSTAIN
Generator
(see Note A)
Q31
Q32
Generator
(see Note A)
Generator
LATCH ENABLE
(see Note A)
SERIAL OUT1
SERIAL OUT2
GND
C
C
L
L
C
= 15 pF
L
(see Note B)
TEST CIRCUIT
NOTES: A. Input pulses are supplied by generators having the following characteristics: t = 100 ns, PRR ≤ 5 MHz, t ≤ 10 ns, t ≤ 10 ns,
w
r
f
Z
C
= 50 Ω.
O
L
B.
includes probe and jig capacitance.
Figure 2. Test Circuit
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
PROPAGATION DELAY TIME,
CLOCK TO SERIAL OUT
vs
FREE-AIR TEMPERATURE
20
15
10
5
125
100
75
50
25
0
V
= 5.5 V
CC
All Q Outputs Low
No Load
V
= 5 V
CC
C
= 15 pF
L
0
0
10
20
30
40
50
60
70
80
0
10
20
T
30
40
50
60
70
80
– Free-Air Temperature – °C
T
– Free-Air Temperature – °C
A
A
Figure 3
Figure 4
DELAY TIME, SUSTAIN INPUT TO Q OUTPUT
DELAY TIME, SUSTAIN INPUT TO Q OUTPUT
LOW TO HIGH
vs
HIGH TO LOW
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
0.5
0.4
0.3
0.2
0.1
0
2
1.5
1
V
= 5 V
= 15 pF
= 91 kΩ
V
C
R
= 5 V
= 15 pF
= 91 kΩ
CC
CC
L
L
C
L
L
R
0.5
0
0
10
20
30
40
50
60
70
80
0
10
20
30
40
50
60
70
80
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 5
Figure 6
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN751508, SN751518
DC PLASMA DISPLAY DRIVERS
SLDS035 – JANUARY 1987 – REVISED NOVEMBER 1989
TYPICAL CHARACTERISTICS
TRANSITION TIME, Q OUTPUT,
LOW TO HIGH
TRANSITION TIME, Q OUTPUT,
HIGH TO LOW
vs
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
5
20
15
10
5
V
C
R
= 5 V
= 15 pF
= 91 kΩ
CC
L
L
V
C
R
= 5 V
= 15 pF
= 91 kΩ
CC
L
L
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
0
0
10
20
30
40
50
60
70
80
0
10
20
30
40
50
60
70
80
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 7
Figure 8
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
microcontroller.ti.com
www.ti.com/lpw
Low Power
Wireless
Telephony
www.ti.com/telephony
Video & Imaging
Wireless
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
microcontroller.ti.com
www.ti.com/lpw
Low Power
Wireless
Telephony
www.ti.com/telephony
Video & Imaging
Wireless
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
microcontroller.ti.com
www.ti.com/lpw
Low Power
Wireless
Telephony
www.ti.com/telephony
Video & Imaging
Wireless
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
microcontroller.ti.com
www.ti.com/lpw
Low Power
Wireless
Telephony
www.ti.com/telephony
Video & Imaging
Wireless
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
microcontroller.ti.com
www.ti.com/lpw
Low Power
Wireless
Telephony
www.ti.com/telephony
Video & Imaging
Wireless
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
microcontroller.ti.com
www.ti.com/lpw
Low Power
Wireless
Telephony
www.ti.com/telephony
Video & Imaging
Wireless
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jun-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
DFP
DFP
DFP
Drawing
SN751508FT
SN751518FT
SN751518FT
OBSOLETE
OBSOLETE
OBSOLETE
FT
48
48
48
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
FT
FT
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lpw
Telephony
Low Power
Wireless
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明