ST20190 [STMICROELECTRONICS]
ADSL, ADSL2 and ADSL+ Modem Chipset for CPE Applications with Utopia II Interface; ADSL , ADSL2和ADSL +调制解调器芯片组CPE应用程序与乌托邦II接口型号: | ST20190 |
厂家: | ST |
描述: | ADSL, ADSL2 and ADSL+ Modem Chipset for CPE Applications with Utopia II Interface |
文件: | 总7页 (文件大小:81K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ST20190
ADSL, ADSL2 and ADSL+
Modem Chipset for CPE Applications with Utopia II Interface
DATA BRIEF
1 APPLICATIONS
Figure 1. Package
■ Low end and high end ADSL Bridge and Router
solutions
■ ADSL Modems / routers for residential and
SOHO broadband access to www and
corporate VPNs
TQFP100
LBGA208
■ Integrated Access Devices offering VoDSL or
VoIP applications
Table 1. Order Codes
■ Home gateway solutions
Part Number
ST20184
Package
TQFP100
LBGA208
2 FEATURES
■ High Integration
ST20196
– 2 chips, Line to ATM
– Direct ATM Interface
– Line Driver integrated
■ Complete modem package
– No dependency on external processor and
easy,straight forward integration with external
network processors
– Highly reduced bill of material cost
■ Support for multiple ADSL standards:
– ANSI T1.413 Issue2
– Full reference design kit for modem manufac-
turers, including schematics, layout, BoM,
HW design guide, firmware
– ITU G.992.1 (G.dmt)
■ Highest Performance
– Annex A, Annex B, Annex C
– ITU G.992.2 (G.Lite)
– Fully rate-adaptive
– ADSL mode > 12 Mbps in Downstream and >
1 Mbps in Upstream
– ITU G.992.3 (ADSL2)
– Annex A, B, C, I, J and L
– ITU G.992.4 (G.Lite bis)
– ITU G.992.5 (ADSL2+)
– Annex A, B, C, I, J and L
– ADSL+ mode > 20 Mbps in Downstream and
> 2 Mbps in Upstream when using 64 tones
(annex L)
3 OVERALL DESCRIPTION
– Support of ReachDSLTM with digital com-
panion chip
The ST20190 is a new generation ADSL chipset
from STMicroelectronics. It is highly integrated
and has the flexibility to offer all standards, all an-
nexes while being fully optimised for CPE applica-
tions. It provides all the required functions to
implement a complete Utopia rate adaptive DMT
ADSL modem. It consists of the optimised ADSL
Analogue Front-End chip ST20184 and the digital
chip ST20196 which includes a DMT/ATM mo-
dem, and a dedicated ADSL Transceiver Control-
ler with associated Firmware.
■ Cat II functionality: Trellis coding and echo
cancellation
■ Dual latency support: fast + interleaved
■ Small footprint packages allow high density
board designs
■ Embedded controller with cache for powerful
and flexible on chip control of the modem
operation
As shown in Fig.2, the chipset interfaces have
been defined to allow direct integration into sys-
tems design, reducing both time-to-market and im-
REV. 1
1/7
June 2004
This is preliminary information on a new product now in development. Details are subject to change without notice.
ST20190
plementation risks. The data interface is implemented as an ATM Utopia interface. A HW/FW command
and control interface (CtrlE) to communicate with external management entities, is directly provided, with-
out need for glue logic.
The chipset employs Discrete Multi-Tone modulation as specified in ANSI T1.413. It also supports ETSI
TS 101 388 and ITU standards G.992.1 (G.dmt) including Annex A, B and C; G.992.2 (G.lite) annex A, B
and C; G.992.3 (ADSL2) including Annex A, B, C, I, J and L; G.992.5 (G.ADSL+) including Annex A, B, C,
I, J and Annex L.
Flexible bit assignment is foreseen to support ADSL overlay over POTS and ISDN but also All Digital loop
and overlapping spectra. Additional Reed-Solomon forward error correction with optional interleaving pro-
vides maximum noise immunity.
4 THE MODEM ENVIRONMENT
An integrated ADSL-compatible line driver is used to drive the telephone twisted pair, and a POTS/ISDN
splitter or adequate distributed filtering is required to split the baseband analogue telephone or ISDN sig-
nal from the modulated ADSL signal. In G.Lite mode, the splitter can be removed and replaced by distrib-
uted POTS filters. Brief characteristics of the system are given in Section 6. The bit rate can be varied in
steps of 32 kbits/s in ADSL and in steps of 1 kbit/s in ADSL2/ADSL+ mode.
Figure 2. Utopia Chipset Block Diagram
Utopia I or II
ATM
ST20196
- DMT Modem
ST20184
~
~
- ATM framer
- Microcontroller
Line
Analog
Front End
Management
Entity
Control
CtrlE
flash
EPROM
SDRAM
(Optional)
5 CHIPSET FUNCTIONS
The functions performed by each IC are as follows:
5.1 ST20184
This CMOS IC contains the analogue functions required in the transceiver. In order to cope with the high
attenuation of the line and in order to maintain an acceptable noise level of the signal, Programmable gain
amplifiers have been implemented at the analogue front of the transmission and reception paths. In Re-
ception, the signal goes through a LNA, a high pass filter to eliminate echo and LNA before a low pass
filter for anti-aliasing. The AD and DA converters provide 14-bit resolution at 2.2 MHz sampling rate.
Finally, for the transmission part, the control of the external hybrid driver is done by a highly integrated
linear line driver.
2/7
ST20190
Figure 3. Block Diagram of ST20184
CTRL/TST
Interface
Hybrid
switches
2.5V Regulator
VCXO
(optional)
Tuning Circuit
I/V Reference
+
POR
Dying Gasp
RXP3
Bypass
RXP1
LNA1ab
LNA1c
RXN1
RXP2
LNA2
ADC
RX HPF
RX LPF
D
I
RXN2
G
I
Bypass
T
A
L
RXN3
5V area
Digital
Loopback
TXP
DAC
TX LPF
TXN
TXLD
5.2 ST20196
5.2.1 Discrete Multi Tone (DMT) Modulation and Demodulation
The ST20196 includes a digital Quadrature Amplitude Modulation (QAM) mapper/demapper which allows
coding of up to 15 bits per tone. The device incorporates the necessary Inverse- and Fast Fourier Trans-
form (IFFT, FFT), an innovative unique Per Tone Equalizer (PTEQ), echo cancelling (EC), Trellis coding
and decoding plus timing units and a fully digital clock recovery scheme (TDI). These last blocks feature
efficient synchronization algorithms to improve the efficiency of the recovery of data. The ST20196 per-
formances rely on embedded programmable cores.
In ADSL2 mode the modem supports diagnostics modes, enhanced power management modes to reduce
the CO power (L2), 1 bit constellation, relocatable and modulated pilot.
5.2.2 Framing Functions
The ST20196 incorporates framing functions for the generic and ATM Transmission Convergence (TC)
layers. The new TC layer architecture is fully under the control of an embedded controller. This provides
the flexibility to adapt to different framing variants via firmware. The TC consists of data scrambling and
Reed-Solomon error correction with and without inter-leaving. It also includes the rate converter function-
ality as defined in G.dmt Annex C. Several framing variants are implemented (such as interleaved and
non-interleaved modes, full and reduced overhead) to ensure compliance with ANSI T1.413 Issue 2 and
ITU G.992.1 (G.dmt), G.992.2 (G.Lite), G.992.3 and G.992.4.
3/7
ST20190
Figure 4. Block Diagram of ST20196
TIC
EBI
SDRAM
CTRL
FLASH
CTRL
RAM
ROM
CTRLE
AFE
Interface
DMT
AHB2APB
ARM946
ATM
Interface
CORE
RT
INTERRUPT
CTR
JTAG
WATCHDOG
GPIO
UART
TIMERS
5.2.3 Interface to Utopia Bus
The IC contains the ATM-related functions to interface with the ATM utopia bus an supports level 1 and 2
modes.
5.2.4 Control of Transceiver Chip
The ST20196 runs the firmware controlling the operations of the ADSL transceiver (AFE, DMT modem,
Framer). During modem initialisation, the controller computes and sets up parameters for all programma-
ble DMT functions, filters and equalizers. The ATM TC includes cell level functions (such as cell delinea-
tion, insertion/ extraction of idle cells, payload scrambling, HEC check) and data frame generation. The
controller is able to run in different rate-adaptive modes as defined by the operator. During operation, the
ST20196 performs continuous line monitoring and initiates consecutive actions as specified by the oper-
ator (e.g. bit-swapping, dynamic bit-rate adaptation, power management, … etc.) and collects perfor-
mance and error information for use by management entities.
5.2.5 Interface to Management Entities
The ST20196 also runs the communication protocol to interface with external management entities. A spe-
cific ADSL modem control interface has been defined to ease the integration with both systems hardware
and firmware. This control communication channel is used to transfer information and commands between
modem and management entities. These commands/responses are fully described in the CtrlE specifica-
tion and can be categorized as follows:
- Configuration of a modem line
- De-allocation of a modem line
- Operational Data Retrieval
- Performance Data Retrieval
- Defect Retrieval
4/7
ST20190
6 SUMMARY OF CHARACTERISTICS ST20190
6.1 ST20184 FEATURES
■ Fully integrated ADSL line driver concept (minimises external components)
■ Standards support for:
– ANSI T1.413 Issue 2
– ITU G.992.1 (G.dmt)
– Annex A, B and C
– ITU G.992.2 (G.lite)
– ITU G.992.3 (ADSL2)
– Annex A, B, C, I, J and L
– ITU G.992.5 (ADSL2+)
– Annex A, B, C, I, J and L
– Support of ReachDSL with digital companion chip
■ 14 bit Σ∆ ADC with equivalent ENOB @ 2.2 MS/s
■ 8.8MS/s DAC (14bits)
■ Integrated ADSL highpass filter for POTS and Echo cancellation
■ Fixed XTAL
■ 2.2MHz signal bandwidth / 4.3 kHz tone spacing
■ Supply voltages: 3.3V and 5V
■ Temperature range: -40°C to 85°C
■ Typical power consumption 900 mW
■ Package: TQFP100
6.2 ST20196 FEATURES
■ DMT modulation
■ Max. number of bit per tone: 15 bits (32766 constellation points)
■ Max. number of tones: 512 tones
■ Flexible bit assignment
■ Max clock speed: 36 MHz
■ Max. tone spacing: 4.325 kHz
■ RS encoder: max code word 256 bytes
■ ATM Processor:
– ATM cell buffering
– Cell counting
– Insert/Extract, Idle/Unassigned ATM cells (rate adaptation)
– ATM HEC generation module (CCITT I.432)
– ATM payload scrambler: payload width: 48 bytes
■ Full support of Utopia level 1 or 2 interface
■ Cached ARM controller for improved performance
■ Modem Command interface
– compatible with Utopia level 2 8-bit parallel management interface
– ST's CtrlE modem control command protocol
– Access through parallel 8bit bus or asynchronous serial port
– Dual port RAM mailbox
■ Interface to ReachDSL™ engine
■ Supply voltages: 3.3V and 1.2V
■ Temperature range: -40°C to 85°C
■ Typical power consumption 700 mW
■ Package: LBGA208
5/7
ST20190
7 DEVELOPMENT SUPPORT FOR THE ST20190
Great care has been taken in defining the ST20190 to ease its integration into system designs. In partic-
ular, this is achieved:
– At hardware level: by using one standard interface (ATM Utopia) both for data transfer and for control
– At firmware level: by clearly separating the modem firmware, run on the embedded Transceiver Con-
troller from other systems related and application-specific functions.
The boundary between the two domains is provided by means of a simple modem control protocol (CTRL-
E). This "packaged modem" approach provides a self-contained ADSL modem solution, allowing system
manufacturers to concentrate on system issues. The ST20190 comes in a package with full firmware,
schematics, Bill of Materials and layout information for the ADSL modem part. It is further supported by a
full development environment comprising:
– Evaluation boards
– PC firmware driver for CTRLE
– DeTONEator S/W for CTRLE to a PC
– ADSL test and control FW running on PC
Table 2. Revision History
Date
Revision
Description of Changes
First Issue in EDOCS dms.
June 2004
1
6/7
ST20190
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2004 STMicroelectronics - All rights reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States
www.st.com
7/7
相关型号:
ST20196
ADSL, ADSL2 and ADSL+ Modem Chipset for CPE Applications with Utopia II Interface
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明