TSH94 [STMICROELECTRONICS]
HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION; 高速低功耗四通道运算放大器，具有待机位置
| 型号： | TSH94 |
| 厂家： | 
ST |
| 描述： | HIGH SPEED LOW POWER QUAD OPERATIONAL AMPLIFIER WITH STANDBY POSITION |
| 文件： | 总11页 (文件大小：557K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TSH94
HIGH SPEED LOW POWER QUAD
OPERATIONAL AMPLIFIER (WITH STANDBY POSITION)
■ 2 SEPARATE STANDBY : REDUCED
CONSUMPTION AND HIGH IMPEDANCE
OUTPUTS
■ LOW SUPPLY CURRENT : 4.5mA
■ HIGH SPEED : 150MHz - 110V/µs
■ UNITY GAIN STABILITY
■ LOW OFFSET VOLTAGE : 3mV
■ LOW NOISE 4.2 nV/√Hz
■ LOW COST
D
SO16
■ SPECIFIED FOR 600Ω AND 150Ω LOADS
(Plastic Micropackage)
■ HIGH VIDEO PERFORMANCES :
Differential Gain : 0.03%
Differential Phase : 0.07°
Gain Flatness : 6MHz, 0.1dB max. @ 10dB
gain
PIN CONNECTIONS (top view)
■ HIGH AUDIO PERFORMANCES
DESCRIPTION
The TSH94 is a quad low power high frequency
op-amp, designated for high quality video signal
processing. The device offers an excellent speed
consumption ratio with 4.5mA per amplifier for
150MHz bandwidth.
High slew rate and low noise make it also suitable
for high quality audio applications.
Output 1
1
2
3
4
5
6
7
16 Output 4
15 Inverting Input 4
Inverting Input 1
-
-
The TSH94 offers 2 separate complementary
STANDBY pins :
+
+
Non-inverting Input 1
14 Non-inverting Input 4
-
+
VC C
13
V
CC
❑ STANDBY 1 acting on the n° 2 operator
❑ STANDBY 2 acting on the n° 3 operator
They reduce the consumption of the correspond-
ing operator and put the output in a high imped-
ance state.
12 Non-inverting Input 3
11 Inverting Input 3
10 Output 3
Non-inverting Input 2
Inverting Input 2
+
-
+
-
Output 2
Standby 2
9
8
Standby 1
ORDER CODE
Package
Part Number
TSH94I
Temperature Range
D
-40°C, +125°C
•
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
October 2000
1/11
TSH94
SCHEMATIC DIAGRAM
+
V CC
stdby
stdby
non inverting
input
Internal
Vref
output
inverting
input
Cc
stdby
stdby
-
VCC
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
V
1)
14
VCC
Vid
Supply Voltage
2)
±5
V
Differential Input Voltage
3)
Vi
-0.3 to 12
-40 to +125
-65 to +150
V
Input Voltage
Toper
Tstg
Operating Free-Air Temperature range
Storage Temperature Range
°C
°C
1. All voltages values, except differential voltage are with respect to network ground terminal
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal
+
3. The magnitude of input and output voltages must never exceed V
+0.3V
CC
OPERATING CONDITIONS
Symbol
Parameter
Value
Unit
V
Supply Voltage
Common Mode Input Voltage Range
7 to 12
VCC
Vic
-
+
V
VCC +2 to VCC -1
2/11
TSH94
ELECTRICAL CHARACTERISTICS
VCC = 5V, VCC = -5V, pin 8 connected to 0V, pin 9 connected to VCC , Tamb = 25°C
+
-
+
(unless otherwise specified)
Symbol
Parameter
Min.
Typ.
Max.
Unit
Input Offset Voltage Vic = Vo = 0V
3
5
Vio
mV
T
min. ≤ Tamb ≤ Tmax.
Input Offset Current
Tmin. ≤ Tamb ≤ Tmax.
Input Bias Current.
Tmin. ≤ Tamb ≤ Tmax.
1
5
2
5
Iio
Iib
µA
µA
mA
dB
dB
dB
15
20
Supply Current (per amplifier, no load)
4.5
100
75
70
6
8
ICC
Tmin. ≤ Tamb ≤ Tmax.
Common-mode Rejection Ratio Vic = -3V to +4V, Vo = 0V
80
70
CMR
SVR
Avd
T
min. ≤ Tamb ≤ Tmax.
Supply Voltage Rejection Ratio VCC = ±5V to ±3V
Tmin. ≤ Tamb ≤ Tmax
60
50
Large Signal Voltage Gain RL = 10kΩ, Vo = ±2.5V
Tmin. ≤ Tamb ≤ Tmax.
57
54
High Level Output Voltage Vid = 1V
RL = 600Ω
3
2.5
2.4
3.5
3
VOH
V
V
RL = 150Ω
Tmin. ≤ Tamb ≤ Tmax.
RL = 150Ω
Low Level Output Voltage Vid = 11V
RL = 600Ω
RL = 150Ω
RL = 150Ω
-3.5
-2.8
-3
-2.5
-2.4
VOL
Tmin. ≤ Tamb ≤ Tmax.
Output Short Circuit Current Vid = ±1V
Source
Sink
Source
20
20
15
15
36
40
Io
mA
Tmin. ≤ Tamb ≤ Tmax.
Sink
Gain Bandwidth Product
GBP
fT
MHz
MHz
V/µs
AVCL = 100, RL = 600Ω, CL = 15pF, f = 7.5MHz
Transition Frequency
Slew Rate
90
150
90
SR
V
in = -2 to +2V, AVCL = +1, RL = 600Ω, CL = 15pF
70
110
4.2
35
en
φm
Equivalent Input Voltage Noise Rs = 50Ω, f = 1kHz
Phase Margin AVM = +1
nV/√Hz
Degrees
dB
VO1/VO2
Gf
Channel Seperation f = 1MHz to 10MHz
Gain Flatness f = DC to 6MHz, AVCL = 10dB
Total Harmonic Distortion f = 1kHz, Vo = ±2.5V, RL = 600Ω
Differential Gain f = 3.58MHz, AVCL = +2, RL = 150Ω
Differential Phase f = 3.58MHz, AVCL = +2, RL = 150Ω
65
0.1
dB
THD
∆G
0.01
0.03
0.07
%
%
∆ϕ
Degree
3/11
TSH94
+
-
STANDBY MODE VCC = 5V, VCC = -5V, Tamb = 25°C (unless otherwise specified)
Symbol
Parameter
Min.
Typ.
Max.
Unit
+
+
+
VSBY
Pin 8/9 Threshold Voltage for STANDBY Mode
V
VCC -2.2
VCC -1.6
VCC -1.0
Total Consumption
Standby 1 & 2 = 0
Standby 1 & 2 = 1
Standby 1 = 1, Standby 2 = 0
13.7
13.7
9.4
ICC SBY
mA
Isol
tON
tOFF
ID
Input/Output Isolation (f = 1MHz to 10MHz)
Time from Standby Mode to Active Mode
Time from Active Mode to Standby Mode
Standby Driving Current
70
200
200
2
dB
ns
ns
pA
pA
pA
IOL
IIL
Output Leakage Current
20
Input Leakage Current
20
LOGIC INPUT
STATUS
Standby 1
Standby 2
Op-Omp 2
Op-Amp 3
Op-Amp 1 & 4
0
0
1
1
0
1
0
1
Enable
Enable
Standby
Enable
Standby
Enable
Enable
Enable
Enable
Enable
Standby
Standby
STANDBY POSITION
STANDBY MODE
To put the device in standby, just apply a logic
level on the standby MOS input. As ground is a vir-
tual level for the device, threshold voltage has
VCC
standby
+
+
been refered to VCC at VCC - 1.6V typ.
In standby mode, the output goes in high imped-
ance in 200ns. Be aware that all maximum rating
must still be followed in this mode. It leads to
swing limitation while using the device in signal
multiplexing configuration with followers, differen-
tial input voltage must not exceed ±5V limiting in-
put swing to 2.5Vpp.
VCC
APPLICATIONS
SIGNAL MULTIPLEXING
SAMPLE AND HOLD
4/11
TSH94
APPLICATIONS
VIDEO LINE TRANSCEIVER WITH REMOTE CONTROL
PRINTED CIRCUIT LAYOUT
As for any high frequency device, a few rules must
be observed when designing the PCB to get the
best performances from this high speed op amp.
❑ All leads must be wide and as short as pos-
sible especially for op amp inputs. This is in
order to decrease parasitic capacitance
and inductance.
❑ Use small resistor values to decrease time
constant with parasitic capacitance.
❑ Choose component sizes as small as pos-
sible (SMD).
❑ On output, decrease capacitor load so as
to avoid circuit stability being degraded
which may cause oscillation. You can also
add a serial resistor in order to minimise its
influence.
From the most to the least important points :
❑ Each power supply lead has to be
by-passed to ground with a 10nF ceramic
capacitor very close to the device and
10µF capacitor.
❑ To provide low inductance and low resist-
ance common return, use a ground plane
or common point return for power and sig-
nal.
5/11
TSH94
INPUT OFFSET VOLTAGE DRIFT VERSUS
TEMPERATURE
STATIC OPEN LOOP VOLTAGE GAIN
LARGE SIGNAL FOLLOWER RESPONSE
SMALL SIGNAL FOLLOWER RESPONSE
OPEN LOOP FREQUENCY RESPONSE AND
PHASE SHIFT
CLOSE LOOP FREQUENCY RESPONSE
6/11
TSH94
AUDIO BANDWIDTH FREQUENCY
RESPONSE AND PHASE SHIFT
GAIN FLATNESS AND PHASE SHIFT VERSUS
FREQUENCY
(TSH94 vs Standard 15MHz Audio Op-Amp)
CROSS TALK ISOLATION VERSUS
FREQUENCY (SO16 PACKAGE)
CROSS TALK ISOLATION VERSUS
FREQUENCY (SO16 PACKAGE)
INPUT/OUTPUT ISOLATION IN STANDBY
MODE (SO16 PACKAGE)
STANDBY SWITCHING
7/11
TSH94
SIGNAL MULTIPLEXING (cf p. 5/10)
COMMON INPUT IMPEDANCE VERSUS
FREQUENCY
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
1k 10k 100k 1M 10M 100M
Frequency (Hz)
DIFFERENTIAL INPUT IMPEDANCE VERSUS
FREQUENCY
120
100
80
60
40
20
1k 10k 100k 1M 10M 100M
Frequency (Hz)
8/11
TSH94
MACROMODEL
Applies to: TSH94I (model without standby)
** Standard Linear Ics Macromodels, 1996.
** CONNECTIONS :
* 1 INVERTING INPUT
* 2 NON-INVERTING INPUT
* 3 OUTPUT
* 4 POSITIVE POWER SUPPLY
* 5 NEGATIVE POWER SUPPLY
.SUBCKT TSH94 1 3 2 4 5 (analog)
********************************************************
.MODEL MDTH D IS=1E-8 KF=1.809064E-15
CJO=10F
FIBN 5 1 VOFN 1.000000E-02
* AMPLIFYING STAGE
FIP 5 19 VOFP 2.530000E+02
FIN 5 19 VOFN 2.530000E+02
RG1 19 5 3.160721E+03
RG2 19 4 3.160721E+03
CC 19 5 2.00000E-09
DOPM 19 22 MDTH 400E-12
DONM 21 19 MDTH 400E-12
HOPM 22 28 VOUT 1.504000E+03
VIPM 28 4 5.000000E+01
HONM 21 27 VOUT 1.400000E+03
VINM 5 27 5.000000E+01
***********************
* INPUT STAGE
CIP 2 5 1.000000E-12
CIN 1 5 1.000000E-12
EIP 10 5 2 5 1
RZP1 5 80 1E+06
EIN 16 5 1 5 1
RZP2 4 80 1E+06
RIP 10 11 2.600000E-01
RIN 15 16 2.600000E-01
RIS 11 15 3.645298E-01
DIP 11 12 MDTH 400E-12
DIN 15 14 MDTH 400E-12
VOFP 12 13 DC 0.000000E+00
VOFN 1314DC 0
GZP 5 82 19 80 2.5E-05
RZP2H 83 4 10000
RZP1H 83 82 80000
RZP2B 84 5 10000
RZP1B 82 84 80000
LZPH 4 83 3.535e-02
LZPB 84 5 3.535e-02
IPOL 13 5 1.000000E-03
CPS 11 15 2.986990E-10
DINN 17 13 MDTH 400E-12
VIN 17 5 2.000000e+00
DINR 15 18 MDTH 400E-12
VIP 4 18 1.000000E+00
FCP 4 5 VOFP 3.500000E+00
FCN 5 4 VOFN 3.500000E+00
FIBP 2 5 VOFP 1.000000E-02
EOUT 26 23 82 5 1
VOUT 23 5 0
ROUT 26 3 35
COUT 3 5 30.000000E-12
DOP 19 25 MDTH 400E-12
VOP 4 25 2.361965E+00
DON 24 19 MDTH 400E-12
VON 24 5 2.361965E+00
.ENDS
ELECTRICAL CHARACTERISTICS
= ±5V, Tamb = 25°C (unless otherwise specificed)
VCC
Symbol
Conditions
Value
Unit
Vio
Avd
ICC
0
3.2
mV
V/mV
mA
RL = 600Ω
No load / Ampli
5.2
Vicm
VOH
VOL
Isink
-3 to 4
+3.6
-3.6
40
V
RL = 600Ω
V
RL = 600Ω
V
Vo = 0V
mA
Isource
GBP
SR
Vo = 0V
40
mA
RL = 600Ω, CL = 15pF
RL = 600Ω, CL = 15pF
RL = 600Ω, CL = 15pF
147
110
42
MHz
V/µs
Degrees
φm
9/11
TSH94
Applies to: TSH94I (model with standby)
ISTB0 4 5 130UA
FIBP 2 5 VOFP 1.000000E-02
FIBN 5 1 VOFN 1.000000E-02
* AMPLIFYING STAGE
FIP 5 19 VOFP 2.530000E+02
FIN 5 19 VOFN 2.530000E+02
RG1 19 120 3.160721E+03
XCOM1 4 0 120 5 COM SWITCH
RG2 19 121 3.160721E+03
XCOM2 4 0 4 121 COM SWITCH
CC 19 5 2.00000E-09
DOPM 19 22 MDTH 400E-12
DONM 21 19 MDTH 400E-12
HOPM 22 28 VOUT 1.504000E+03
VIPM 28 4 5.000000E+01
HONM 21 27 VOUT 1.400000E+03
VINM 5 27 5.000000E+01
*********** ZP **********
RZP1 5 80 1E+06
* 1 INVERTING INPUT
* 2 NON-INVERTING INPUT
* 3 OUTPUT
* 4 POSITIVE POWER SUPPLY
* 5 NEGATIVE POWER SUPPLY
* 6 STANDBY
.SUBCKT TSH94 1 3 2 4 5 6 (analog)
********************************************************
**************** switch *******************
.SUBCKT SWITCH20 10 IN OUT COM
.MODEL DIDEAL D N=0.1 IS=1E-08
DP IN 1 DIDEAL 400E-12
DN OUT 2 DIDEAL 400E-12
EP 1 OUT COM 10 2
EN 2 IN COM 10 2
RFUIT1 IN 1 1E+09
RFUIT2 OUT 2 1E+09
RCOM COM 0 1E+12
.ENDS SWITCH
RZP2 4 80 1E+06
GZP 5 82 19 80 2.5E-05
RZP2H 83 4 10000
RZP1H 83 82 80000
RZP2B 84 5 10000
RZP1B 82 84 80000
LZPH 4 83 3.535e-02
LZPB 84 5 3.535e-02
**************************
EOUT 26 23 82 5 1
**************** inverter *****************
.SUBCKT INV 20 10 IN OUT
.MODEL DIDEAL D N=0.1 IS=1E-08
RP1 20 15 1E+09
RN1 15 10 1E+09
RIN IN 10 1E+12
RIP IN 20 1E+12
DPINV OUT 20 DIDEAL 400E-12
DNINV 10 OUT DIDEAL 400E-12
GINV 0 OUT IN 15 -6.7E-7
CINV 0 OUT 210f
VOUT 23 5 0
ROUT 26 103 35
.ENDS INV
***************** AOP **********************
.MODEL MDTH D IS=1E-8 KF=1.809064E-15
CJO=10F
* INPUT STAGE
CIP 2 5 1.000000E-12
CIN 1 5 1.000000E-12
EIP 10 5 2 5 1
EIN 16 5 1 5 1
RIP 10 11 2.600000E-01
RIN 15 16 2.600000E-01
RIS 11 15 3.645298E-01
DIP 11 12 MDTH 400E-12
DIN 15 14 MDTH 400E-12
VOFP 12 13 DC 0.000000E+00
VOFN 1314DC 0
FPOL 13 5 VSTB 1E+03
CPS 11 15 2.986990E-10
DINN 17 13 MDTH 400E-12
VIN 17 5 2.000000e+00
DINR 15 18 MDTH 400E-12
VIP 4 18 1.000000E+00
FCP 4 5 VOFP 3.500000E+00
FCN 5 4 VOFN 3.500000E+00
COUT 103 5 30.000000E-12
XCOM 4 0 103 3 COM SWITCH
DOP 19 25 MDTH 400E-12
VOP 4 25 2.361965E+00
DON 24 19 MDTH 400E-12
VON 24 5 2.361965E+00
********** STAND BY ********
RMI1 4 111 1E+7
RMI2 0 111 2E+7
RONOFF 6 60 1K
CONOGG 60 0 10p
RSTBIN 60 0 1E+12
ESTBIN 106 0 6 0 1
ESTBREF 106 107 111 0 1
DSTB1 107 108 MDTH 400E-12
VSTB 108 109 0
ISTB 109 0 1U
RSTB 109 110 1
DSTB2 0 110 MDTH 400E-12
XINV 4 0 6 COM INV
.ENDS
10/11
TSH94
PACKAGE MECHANICAL DATA
16 PINS - PLASTIC MICROPACKAGE (SO)
Millimeters
Dim.
Inches
Typ.
Min.
Typ.
Max.
Min.
Max.
A
a1
a2
b
1.75
0.2
0.069
0.008
0.063
0.018
0.010
0.1
0.004
1.6
0.35
0.19
0.46
0.25
0.014
0.007
b1
C
0.5
0.020
c1
D
45° (typ.)
9.8
5.8
10
0.386
0.228
0.394
0.244
E
6.2
e
1.27
8.89
0.050
0.350
e3
F
3.8
4.6
0.5
4.0
5.3
0.150
0.181
0.020
0.157
0.209
0.050
0.024
G
L
1.27
0.62
M
S
8° (max.)
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics.
Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all
information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support
devices or systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2000 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
© http://www.st.com
11/11
相关型号：
TSH95IDT
QUAD OP-AMP, 6000uV OFFSET-MAX, 150MHz BAND WIDTH, PDSO16, ROHS COMPLIANT, PLASTIC, SOP-16
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明