TSV612AIST [STMICROELECTRONICS]
Rail-to-rail input/output 10 μA, 120 kHz CMOS operational amplifiers; 轨到轨输入/输出10 μA ， 120 kHz的CMOS运算放大器
| 型号： | TSV612AIST |
| 厂家： | 
ST |
| 描述： | Rail-to-rail input/output 10 μA, 120 kHz CMOS operational amplifiers |
| 文件： | 总19页 (文件大小：821K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TSV611, TSV611A, TSV612, TSV612A
Rail-to-rail input/output 10 µA, 120 kHz
CMOS operational amplifiers
Features
TSV611ILT - TSV611ICT
■ Rail-to-rail input and output
VCC+
In+
VCC-
In-
1
2
3
5
■ Low power consumption: 10 µA typ at 5 V
■ Low supply voltage: 1.5 to 5.5 V
■ Gain bandwidth product: 120 kHz typ
■ Unity gain stable
+
_
4
Out
SOT23-5/SC70-5
■ Low input offset voltage: 800 µV max (A
TSV612IST - TSV612ID/DT
version)
■ Low input bias current: 1 pA typ
■ Temperature range: -40 to +85° C
Out1
In1-
1
2
3
4
8
7
6
5
VCC+
Out2
In2-
_
+
_
+
In1+
VCC-
Applications
In2+
■ Battery-powered applications
■ Smoke detectors
MiniSO-8/SO-8
■ Proximity sensors
■ Portable devices
■ Signal conditioning
■ Active filtering
■ Medical instrumentation
Description
The TSV61x family of single and dual operational
amplifiers offers low voltage, low power operation
and rail-to-rail input and output.
The devices also feature an ultra-low input bias
current as well as a low input offset voltage.
The TSV61x have a gain bandwidth product of
120 kHz while consuming only 10 µA at 5 V.
These features make the TSV61x family ideal for
sensor interfaces, battery supplied and portable
applications, as well as active filtering.
January 2010
Doc ID 15768 Rev 2
1/19
www.st.com
19
Absolute maximum ratings and operating conditions
TSV611, TSV611A, TSV612, TSV612A
1
Absolute maximum ratings and operating conditions
Table 1.
Symbol
Absolute maximum ratings
Parameter
Value
Unit
VCC
Vid
Supply voltage(1)
Differential input voltage (2)
Input voltage (3)
6
VCC
V
V
Vin
VCC- -0.2 to VCC++0.2
-65 to +150
V
Tstg
Storage temperature
Thermal resistance junction to ambient(4)(5)
SC70-5
°C
205
250
190
125
150
4
Rthja
SOT23-5
°C/W
MiniSO-8
SO-8
Tj
Maximum junction temperature
HBM: human body model(6)
MM: machine model(7)
CDM: charged device model(8)
Latch-up immunity
°C
kV
V
ESD
200
1.5
200
kV
mA
1. All voltage values, except differential voltage are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. Vcc-Vin must not exceed 6 V.
4. Short-circuits can cause excessive heating and destructive dissipation.
5. Rth are typical values.
6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
8. Charged device model: all pins plus package are charged together to the specified voltage and then
discharged directly to ground.
Table 2.
Symbol
Operating conditions
Parameter
Value
Unit
VCC
Vicm
Toper
Supply voltage
1.5 to 5.5
VCC- -0.1 to VCC+ +0.1
-40 to +85
V
V
Common mode input voltage range
Operating free air temperature range
°C
2/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Electrical characteristics
2
Electrical characteristics
Table 3.
Electrical characteristics at V
= +1.8 V
CC+
with V
= 0 V, V
= V /2, T
= 25° C, and R connected to V /2
CC-
icm
CC
amb
L
CC
(unless otherwise specified)
Symbol
Parameter
Conditions
Min. Typ. Max.
Unit
DC performance
TSV61x
4
TSV61xA
0.8
Vio
Offset voltage
mV
Tmin. < Top < Tmax. TSV61x
Tmin. < Top < TmaxTSV61xA
5
2
DVio
Iio
Input offset voltage drift
2
μV/°C
pA
1
1
10(1)
100
Input offset current
(Vout = Vcc/2)
T
T
min. < Top < Tmax.
pA
1
10(1)
pA
Input bias current
(Vout = Vcc/2)
Iib
min. < Top < Tmax.
1
100
pA
0 V to 1.8 V, Vout = 0.9 V
Tmin. < Top < Tmax.
55
53
71
dB
Common mode rejection
ratio 20 log (ΔVic/ΔVio)
CMR
dB
RL = 10 kΩ, Vout = 0.5 V to
78
74
83
dB
dB
1.3 V
Avd
Large signal voltage gain
Tmin. < Top < Tmax.
35
50
4
7
RL = 10 kΩ
VOH
High level output voltage
Low level output voltage
Isink
mV
Tmin. < Top < Tmax.
35
50
RL = 10 kΩ
Tmin. < Top < Tmax.
VOL
mV
mA
Vo = 1.8 V
9
9
13
10
9
Tmin. < Top < Tmax.
Iout
Vo = 0 V
8
8
Isource
Tmin. < Top < Tmax.
No load, Vout = Vcc/2
Tmin. < Top < Tmax.
6.5
6
12
µA
µA
Supply current (per
operator)
ICC
12.5
AC performance
GBP Gain bandwidth product
RL = 10 kΩ, CL = 20 pF
RL = 10 kΩ, CL = 20 pF
RL = 10 kΩ, CL = 20 pF
100
60
kHz
Degrees
dB
φm
Phase margin
Gain margin
Gm
9.5
RL = 10 kΩ, CL = 20 pF,
Vout = 0.5V to 1.3V
SR
Slew rate
0.03
V/μs
Doc ID 15768 Rev 2
3/19
Electrical characteristics
Table 3.
TSV611, TSV611A, TSV612, TSV612A
= +1.8 V
Electrical characteristics at V
CC+
with V
= 0 V, V
= V /2, T
= 25° C, and R connected to V /2
CC-
icm
CC
amb
L
CC
(unless otherwise specified) (continued)
Symbol
Parameter Conditions
Min. Typ. Max.
Unit
Equivalent input noise
voltage
nV
en
f = 1 kHz
110
-----------
Hz
Fin = 1 kHz, Av = 1,
Vout = 1 Vpp, RL = 100 kΩ,
BW = 22 kHz
Total harmonic distortion +
noise
THD+N
0.07
%
1. Guaranteed by design.
4/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Electrical characteristics
Table 4.
Symbol
V
= +3.3 V, V
= 0 V, V
= V /2, T
= 25° C,
CC+
CC-
icm
CC
amb
R connected to V /2 (unless otherwise specified)
L
CC
Parameter
Min. Typ. Max.
Unit
DC performance
TSV61x
4
TSV61xA
0.8
Vio
Offset voltage
mV
Tmin<Top<Tmax TSV61x
Tmin<Top<TmaxTSV61xA
5
2
DVio
Iio
Input offset voltage drift
Input offset current
2
μV/°C
pA
1
1
10(1)
100
Tmin. < Top < Tmax.
pA
1
10(1)
pA
Iib
Input bias current
Tmin. < Top < Tmax.
1
100
pA
0 V to 3.3 V, Vout = 1.75 V
Tmin. < Top < Tmax.
61
58
76
dB
Common mode rejection
ratio 20 log (ΔVic/ΔVio)
CMR
dB
RL = 10 kΩ, Vout = 0.5 V to
85
83
92
dB
dB
2.8 V
Avd
Large signal voltage gain
Tmin. < Top < Tmax.
35
50
5
RL = 10 kΩ
VOH
High level output voltage
Low level output voltage
Isink
mV
Tmin. < Top < Tmax.
10
44
38
9.5
35
50
RL = 10 kΩ
Tmin. < Top < Tmax.
VOL
mV
mA
Vo = VCC
37
35
Tmin. < Top < Tmax.
Iout
Vo = 0 V
32
30
Isource
Tmin. < Top < Tmax.
No load, Vout = VCC/2
6.5
6
12.5
13
µA
µA
Supply current (per
operator)
ICC
T
min. < Top < Tmax.
AC performance
GBP Gain bandwidth product
RL = 10 kΩ, CL = 20 pF
RL = 10 kΩ, CL = 20 pF
RL = 10 kΩ, CL = 20 pF,
110
60
kHz
Degrees
dB
φm
Phase margin
Gain margin
Gm
9.5
RL = 10 kΩ, CL = 20 pF, Vout
SR
en
Slew rate
0.035
110
V/μs
= 0.5V to 2.8V
Equivalent input noise
voltage
nV
f = 1 kHz
-----------
Hz
1. Guaranteed by design.
Doc ID 15768 Rev 2
5/19
Electrical characteristics
TSV611, TSV611A, TSV612, TSV612A
Table 5.
Symbol
V
= +5 V, V
= 0 V, V
= V /2, T
= 25° C, R connected to V /2
CC+
CC-
icm
CC
amb
L
CC
(unless otherwise specified)
Parameter
Min. Typ. Max.
Unit
DC performance
TSV61x
TSV61xA
4
0.8
Vio
Offset voltage
mV
Tmin<Top<Tmax TSV61x
Tmin<Top<Tmax TSV61xA
5
2
DVio
Iio
Input offset voltage drift
Input offset current
2
μV/°C
pA
1
1
10(1)
100
Tmin. < Top < Tmax.
pA
1
10(1)
pA
Iib
Input bias current
Tmin. < Top < Tmax.
0 V to 5 V, Vout = 2.5 V
Tmin. < Top < Tmax.
Vcc = 1.8 to 5 V
1
100
pA
64
63
76
74
80
dB
Common mode rejection
ratio 20 log (ΔVic/ΔVio)
CMR
SVR
dB
93
93
dB
Supply voltage rejection
ratio 20 log (ΔVcc/ΔVio)
T
min. < Top < Tmax.
dB
RL = 10 kΩ, Vout = 0.5 V to
4.5 V
88
85
dB
dB
Avd
Large signal voltage gain
T
min<Top<Tmax
35
50
7
16
RL = 10 kΩ
VOH
High level output voltage
Low level output voltage
Isink
mV
Tmin. < Top < Tmax.
35
50
RL = 10 kΩ
Tmin. < Top < Tmax.
VOL
mV
mA
Vo = VCC
52
42
57
Tmin. < Top < Tmax.
Iout
Vo = 0 V
58
49
63
Isource
Tmin. < Top < Tmax.
No load, Vout = VCC/2
Tmin. < Top < Tmax.
7.5
7
10.5
14
15
µA
µA
Supply current (per
operator)
ICC
AC performance
GBP Gain bandwidth product
RL = 10 kΩ, CL = 20 pF
RL = 10 kΩ, CL = 20 pF
RL = 10 kΩ, CL = 20 pF
120
62
kHz
Degrees
dB
φm
Phase margin
Gain margin
Gm
10
RL = 10 kΩ, CL = 20 pF,
Vout = 0.5V to 4.5V
SR
Slew rate
0.04
V/μs
6/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Electrical characteristics
Table 5.
V
= +5 V, V
= 0 V, V
= V /2, T
= 25° C, R connected to V /2
CC+
CC-
icm
CC
amb
L
CC
(unless otherwise specified) (continued)
Symbol
Parameter
Min. Typ. Max.
Unit
Equivalent input noise
f = 1 kHz
nV
en
105
-----------
voltage
Hz
Fin = 1 kHz, Av = 1,
Total harmonic distortion +
Vout = 1 Vpp, RL = 100 kΩ,
noise
THD+N
0.02
%
BW = 22kHz
1. Guaranteed by design.
Figure 1.
Supply current vs. supply voltage Figure 2.
Output current vs. output voltage at
V = 1.5 V
CC
at V
= V /2
icm
CC
Figure 3.
Output current vs. output voltage at Figure 4.
= 5 V
Voltage gain and phase vs.
frequency at V = 1.5 V
V
CC
CC
Doc ID 15768 Rev 2
7/19
Electrical characteristics
TSV611, TSV611A, TSV612, TSV612A
Phase margin vs. output current
Figure 5.
Figure 7.
Figure 9.
Voltage gain and phase vs.
frequency at V = 5 V
Figure 6.
CC
Positive slew rate vs. time, VCC = 1.5 V, Figure 8.
CLoad = 100 pF, RLoad = 10 kΩ
Negative slew rate vs. time, VCC = 1.5 V,
CLoad = 100 pF, RLoad = 10 kΩ
VCC=1.5V, Vicm=VCC/2,
T=85°C
T=−40°C
RLoad=10k
Ω, CLoad=100pF
VLoad=VCC/2
T=-40°C
T=25°C
T=85°C
VCC=1.5V, Vicm=VCC/2
RLoad=10kΩ, CLoad=100pF
T=25°C
Time (µs)
Time (µs)
Positive slew rate vs. time, VCC = 5.5 V, Figure 10.
Negative slew rate vs. time, VCC = 5.5 V,
CLoad = 100 pF, RLoad = 100 kΩ
CLoad = 100 pF, RLoad = 100 kΩ
Ω
Ω
8/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Figure 11. Slew rate vs. supply voltage
Electrical characteristics
Figure 12. Noise vs. frequency at Vcc = 5 V
Vicm=2.5V
Vicm=4.5V
VCC=5V
T=25
°
C
Frequency (Hz)
Figure 13. Distortion + noise vs. frequency
Figure 14. Distortion + noise vs. output
voltage
1
Vcc=1.5V
Vcc=1.5V
Rl=10kohms
Rl=10k
Ω
0.1
Vcc=1.5V
Rl=100kohms
Vcc=1.5V
Rl=100k
Ω
Vcc=5.5V
f=1kHz
Rl=10kohms
Gain=1
BW=22kHz
Vicm=Vcc/2
Ω
Vcc=5.5V
Rl=100kohms
0.01
Ω
10
100
1000
10000
Output Voltage (Vpp)
Figure 15. Voltage gain and phase vs.
Figure 16. Voltage gain and phase vs.
frequency at V = 1.8 V (based on
frequency at V = 5 V (based on
CC
CC
simulation results)
simulation results)
Doc ID 15768 Rev 2
9/19
Application information
TSV611, TSV611A, TSV612, TSV612A
3
Application information
3.1
Operating voltages
The TSV61x can operate from 1.5 to 5.5 V. Their parameters are fully specified for 1.8, 3.3
and 5 V power supplies. However, the parameters are very stable in the full V range and
CC
several characterization curves show the TSV61x characteristics at 1.5 V. Additionally, the
main specifications are guaranteed in extended temperature ranges from -40° C to +85° C.
3.2
Rail-to-rail input
The TSV61x are built with two complementary PMOS and NMOS input differential pairs.
The devices have a rail-to-rail input, and the input common mode range is extended from
V
-0.1 V to V
+0.1 V. The transition between the two pairs appears at V
-0.7 V. In
CC-
CC+
CC+
the transition region, the performance of CMRR, PSRR, V and THD is slightly degraded
io
(as shown in Figure 17 and Figure 18 for V vs. V ).
io
icm
Figure 17. Input offset voltage vs input
Figure 18. Input offset voltage vs input
common mode at V = 5 V
common mode at V = 1.5 V
CC
CC
1.4
1.2
1.5
1.0
1.0
0.8
0.6
0.5
0.4
0.2
0.0
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.5
-1.0
-1.5
0.0
1.0
2.0
3.0
4.0
5.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
Input Common Mode Voltage (V)
Input Common Mode Voltage (V)
The device is guaranteed without phase reversal.
3.3
3.4
Rail-to-rail output
The operational amplifiers’ output levels can go close to the rails: less than 35 mV above
GND rail and less than 35 mV below V rail when connected to 10 kΩ load to V /2.
CC
CC
Driving resistive and capacitive loads
These products are micro-power, low-voltage operational amplifiers optimized to drive rather
large resistive loads, above 10 kΩ. For lower resistive loads, the THD level may significantly
increase.
10/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Application information
In a follower configuration, these operational amplifiers can drive capacitive loads up to
100 pF with no oscillations. When driving larger capacitive loads, adding an in-series
resistor at the output can improve the stability of the devices (see Figure 19 for
recommended in-series resistor values). Once the in-series resistor value has been
selected, the stability of the circuit should be tested on bench and simulated with the
simulation model.
Figure 19. In-series resistor vs. capacitive load
3.5
3.6
PCB layouts
For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible
to the power supply pins.
Macromodel
An accurate macromodel of the TSV61x is available on STMicroelectronics’ web site at
www.st.com. This model is a trade-off between accuracy and complexity (that is, time
simulation) of the TSV61x operational amplifiers. It emulates the nominal performances of a
typical device within the specified operating conditions mentioned in the datasheet. It also
helps to validate a design approach and to select the right operational amplifier, but it does
not replace on-board measurements.
Doc ID 15768 Rev 2
11/19
Package information
TSV611, TSV611A, TSV612, TSV612A
4
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
12/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Package information
4.1
SOT23-5 package information
Figure 20. SOT23-5 package mechanical drawing
Table 6.
Ref.
SOT23-5 package mechanical data
Dimensions
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
B
0.90
1.20
1.45
0.15
1.30
0.50
0.20
3.00
0.035
0.047
0.057
0.006
0.051
0.019
0.008
0.118
0.90
0.35
0.09
2.80
1.05
0.40
0.15
2.90
1.90
0.95
2.80
1.60
0.35
0.035
0.013
0.003
0.110
0.041
0.015
0.006
0.114
0.075
0.037
0.110
0.063
0.013
C
D
D1
e
E
2.60
1.50
3.00
1.75
0.102
0.059
0.004
0.118
0.069
0.023
F
L
0.10
0.60
K
0 degrees
10 degrees
Doc ID 15768 Rev 2
13/19
Package information
TSV611, TSV611A, TSV612, TSV612A
4.2
SC70-5 (SOT323-5) package information
Figure 21. SC70-5 (SOT323-5) package mechanical drawing
SIDE VIEW
DIMENSIONS IN MM
GAUGE PLANE
COPLANAR LEADS
SEATING PLANE
TOP VIEW
Table 7.
Ref
SC70-5 (SOT323-5) package mechanical data
Dimensions
Millimeters
Inches
Typ
Min
Typ
Max
Min
Max
A
A1
A2
b
0.80
1.10
0.10
1.00
0.30
0.22
2.20
2.40
1.35
0.315
0.043
0.004
0.039
0.012
0.009
0.087
0.094
0.053
0.80
0.15
0.10
1.80
1.80
1.15
0.90
0.315
0.006
0.004
0.071
0.071
0.045
0.035
c
D
2.00
2.10
1.25
0.65
1.30
0.36
0.079
0.083
0.049
0.025
0.051
0.014
E
E1
e
e1
L
0.26
0°
0.46
8°
0.010
0.018
<
14/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Package information
4.3
SO-8 package information
Figure 22. SO-8 package mechanical drawing
Table 8.
Ref.
SO-8 package mechanical data
Millimeters
Dimensions
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.75
0.25
0.069
0.010
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.48
0.23
5.00
6.20
4.00
0.019
0.010
0.197
0.244
0.157
c
D
4.90
6.00
3.90
1.27
0.193
0.236
0.154
0.050
E
E1
e
h
0.25
0.40
0.50
1.27
0.010
0.016
0.020
0.050
L
L1
k
1.04
0.040
1°
8°
1°
8°
ccc
0.10
0.004
Doc ID 15768 Rev 2
15/19
Package information
TSV611, TSV611A, TSV612, TSV612A
4.4
MiniSO-8 package information
Figure 23. MiniSO-8 package mechanical drawing
Table 9.
Ref.
MiniSO-8 package mechanical data
Millimeters
Dimensions
Inches
Typ.
Min.
Typ.
Max.
Min.
Max.
A
A1
A2
b
1.1
0.043
0.006
0.037
0.016
0.009
0.126
0.203
0.122
0
0.15
0.95
0.40
0.23
3.20
5.15
3.10
0
0.75
0.22
0.08
2.80
4.65
2.80
0.85
0.030
0.009
0.003
0.11
0.033
c
D
3.00
4.90
3.00
0.65
0.60
0.95
0.25
0.118
0.193
0.118
0.026
0.024
0.037
0.010
E
0.183
0.11
E1
e
L
0.40
0°
0.80
0.016
0°
0.031
L1
L2
k
8°
8°
ccc
0.10
0.004
16/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Ordering information
5
Ordering information
Table 10. Order codes
Temperature
Order code
Package
SOT23-5
SC70-5
SO-8
Packing
Marking
range
TSV611ILT
K12
K11
TSV611AILT
TSV611ICT
TSV611AICT
TSV612ID/DT
TSV612AID/DT
TSV612IST
Tape & reel
K12
K11
-40° C to 85° C
V612I
V612AI
K113
K115
Tube & tape & reel
Tape & reel
MiniSO-8
TSV612AIST
Doc ID 15768 Rev 2
17/19
Revision history
TSV611, TSV611A, TSV612, TSV612A
6
Revision history
Table 11. Document revision history
Date
Revision
Changes
28-May-2009
1
Initial release.
Full datasheet for product now in production.
18-Jan-2010
2
Added Figure 1 to Figure 19.
18/19
Doc ID 15768 Rev 2
TSV611, TSV611A, TSV612, TSV612A
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 15768 Rev 2
19/19
相关型号：
©2020 ICPDF网 联系我们和版权申明