UA741CDCDT [STMICROELECTRONICS]
General-purpose single operational amplifier;型号: | UA741CDCDT |
厂家: | ST |
描述: | General-purpose single operational amplifier |
文件: | 总11页 (文件大小:315K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UA741
General-purpose single operational amplifier
Datasheet - production data
Features
N
• Large input voltage range
• No latch-up
DIP8
(plastic package)
• High gain
• Short-circuit protection
• No frequency compensation required
• Same pin configuration as the UA709
D
SO8
Applications
(plastic micropackage)
• Summing amplifiers
• Voltage followers
• Integrators
• Active filters
Pin connections
• Function generators
(top view)
Description
The UA741 is a high performance monolithic
operational amplifier constructed on a single
silicon chip. It is intended for a wide range of
analog applications.
The high gain and wide range of operating
voltages provide superior performances in
integrators, summing amplifiers and general
feedback applications. The internal compensation
network (6 dB/octave) ensures stability in closed-
loop circuits.
1 - Offset null 1
2 - Inverting input
3 - Non-inverting input
-
4 - V
CC
5 - Offset null 2
6 - Output
+
7 - V
CC
8 - N.C.
September 2013
DocID5304 Rev 3
1/11
This is information on a product in full production.
www.st.com
Contents
UA741
Contents
1
2
3
4
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1
4.2
DIP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5
6
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2/11
DocID5304 Rev 3
UA741
Schematic diagram
1
Schematic diagram
Figure 1. Schematic diagram
Non-Inverting input
Vcc+
Q12
Q8
Q13
Q9
Inverting
input
Q14
R7
4.5kW
Q1
Q2
C1
30pF
Q15
Q18
R5
39kW
R9
25W
R8
7.5kW
Q3
Q4
Output
R10
50W
Q16
Q7
Q17
Q20
Q11 Q22
Q10
Q5
Q6
Offset
null 1
R3
50kW
R2
1kW
R4
5kW
R1
1kW
R11
50W
R12
50kW
Vcc-
Offset
null 2
DocID5304 Rev 3
3/11
11
Absolute maximum ratings and operating conditions
UA741
2
Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings
Parameter
Symbol
Value
Unit
VCC
Vid
Vi
Supply voltage
±22
±30
Differential input voltage
Input voltage
V
±15
Output short-circuit duration
Infinite
Thermal resistance junction to ambient
Rthja
DIP8
SO8
85
125
°C/W
Thermal resistance junction to case
Rthjc
DIP8
SO8
41
40
HBM: human body model(1)
DIP package
500
400
V
SO package
ESD
Tstg
MM: machine model(2)
100
1.5
CDM: charged device model(3)
Storage temperature range
kV
°C
-65 to +150
1. Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a
1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
2. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
3. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.
Table 2. Operating conditions
Symbol
Parameter
UA741I
UA741C
Unit
VCC
Vicm
Toper
Supply voltage
5 to 40
±12
V
Common mode input voltage range
Operating free air temperature range
-40 to +105
0 to +70
°C
4/11
DocID5304 Rev 3
UA741
Electrical characteristics
3
Electrical characteristics
Table 3. Electrical characteristics at V = ±15 V, T
= 25 °C
CC
amb
(unless otherwise specified)
Symbol
Parameter
Min.
Typ.
Max.
Unit
Input offset voltage (Rs ≤10 kΩ)
Vio
mV
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
1
5
6
Input offset current
Iio
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
2
30
70
nA
Input bias current
Iib
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
10
100
200
Large signal voltage gain (Vo = ±10 V, RL = 2 kΩ)
Avd
SVR
ICC
Vicm
V/mV
dB
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
50
25
200
90
Supply voltage rejection ratio (Rs ≤10 kΩ)
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
77
77
Supply current, no load
mA
V
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
1.7
2.8
3.3
Input common mode voltage range
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
±12
±12
Common mode rejection ratio (RS ≤10 kΩ)
CMR
IOS
dB
Tamb = +25 °C
Tmin ≤Tamb ≤Tmax
70
70
90
25
Output short circuit current
10
40
mA
Output voltage swing
Tamb = +25 °C
RL = 10 kΩ
RL = 2 kΩ
RL = 10 kΩ
RL = 2 kΩ
12
10
12
10
14
13
±Vopp
V
Tmin ≤Tamb ≤Tmax
Slew rate
SR
tr
0.25
0.5
0.3
V/μs
μs
Vi = ±10 V, RL = 2 kΩ, CL = 100 pF, unity gain
Rise time
Vi = ±20 mV, RL = 2 kΩ, CL = 100 pF, unity gain
Overshoot
Kov
Ri
5
2
%
Vi = 20 mV, RL = 2 kΩ, CL = 100 pF, unity gain
Input resistance
0.3
MΩ
DocID5304 Rev 3
5/11
11
Electrical characteristics
UA741
Table 3. Electrical characteristics at V = ±15 V, T
= 25 °C
CC
amb
(unless otherwise specified) (continued)
Symbol
Parameter Min.
Typ.
Max.
Unit
Gain bandwidth product
GBP
0.7
1
MHz
Vi = 10 mV, RL = 2 kΩ, CL = 100 pF, f =100 kHz
Total harmonic distortion
THD
0.06
%
f = 1 kHz, Av = 20 dB, RL = 2 kΩ, Vo = 2 Vpp, CL = 100 pF,
Tamb = +25° C
Equivalent input noise voltage
nV
en
23
50
-----------
f = 1 kHz, Rs = 100 Ω
Hz
∅m
Phase margin
Degree
6/11
DocID5304 Rev 3
UA741
Package information
4
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
DocID5304 Rev 3
7/11
11
Package information
UA741
4.1
DIP8 package information
Figure 2. DIP8 package mechanical drawing
Table 4. DIP8 package mechanical data
Dimensions
Ref.
Millimeters
Typ.
Inches
Min.
Max.
Min.
Typ.
Max.
A
A1
A2
b
5.33
0.210
0.38
2.92
0.36
1.14
0.20
9.02
7.62
6.10
0.015
0.115
0.014
0.045
0.008
0.355
0.300
0.240
3.30
0.46
1.52
0.25
9.27
7.87
6.35
2.54
7.62
4.95
0.56
1.78
0.36
10.16
8.26
7.11
0.130
0.018
0.060
0.010
0.365
0.310
0.250
0.100
0.300
0.195
0.022
0.070
0.014
0.400
0.325
0.280
b2
c
D
E
E1
e
eA
eB
L
10.92
3.81
0.430
0.150
2.92
3.30
0.115
0.130
8/11
DocID5304 Rev 3
UA741
Package information
4.2
SO8 package information
Figure 3. SO8 package mechanical drawing
Table 5. SO8 package mechanical data
Dimensions
Ref.
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.75
0.25
0.069
0.010
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.48
0.23
5.00
6.20
4.00
0.019
0.010
0.197
0.244
0.157
c
D
4.90
6.00
3.90
1.27
0.193
0.236
0.154
0.050
E
E1
e
h
0.25
0.40
0.50
1.27
0.010
0.016
0.020
0.050
L
L1
k
1.04
0.040
0
8 °
1 °
8 °
ccc
0.10
0.004
DocID5304 Rev 3
9/11
11
Ordering information
UA741
5
Ordering information
Table 6. Order codes
Package
Temperature
range
Order code
UA741CN
Packing
Marking
DIP8
SO-8
DIP8
SO-8
Tube
UA741CN
741C
0° C, +70° C
Tube or
tape & reel
UA741CD/CDT
UA741IN
Tube
UA741IN
741I
-40° C, +105° C
Tube or tape &
reel
UA741ID/IDT
6
Revision history
Table 7. Document revision history
Changes
Date
Revision
01-Nov-2001
1
Initial release.
Document reformatted.
Added ESD values and thermal resistances in Table 1: Absolute
maximum ratings.
25-May-2009
02-Sep-2013
2
3
Added Table 2: Operating conditions.
Removed UA741M information and order code in Table 6.
Table 6: Order codes: updated marking for order codes
UA741CD/CDT and UA741ID/IDT.
10/11
DocID5304 Rev 3
UA741
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
DocID5304 Rev 3
11/11
11
相关型号:
©2020 ICPDF网 联系我们和版权申明