SMB110 [SUMMIT]
Five Channel Programmable DC-DC System Power Manager; 五通道可编程直流 - 直流系统电源管理器
| 型号： | SMB110 |
| 厂家： | 
SUMMIT MICROELECTRONICS, INC. |
| 描述： | Five Channel Programmable DC-DC System Power Manager |
| 文件： | 总34页 (文件大小：498K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SMB110
Preliminary Information
Five Channel Programmable DC-DC System Power Manager
FEATURES & APPLICATIONS
INTRODUCTION
• Digital programming of all major parameters via I2C
interface and non-volatile memory
o Output voltage set point
The SMB110 is a highly integrated and flexible five-channel
power manager designed for use in a wide range of portable
applications. The built-in digital programmability allows system
designers to custom tailor the device to suit almost any multi-
channel power supply application from digital camcorders to
mobile phones. Complete with a user friendly GUI, all
programmable settings including output voltages and
input/output voltage monitoring can be customized with ease.
o Output power-up/down sequencing
o Input/Battery voltage monitoring
o Digital soft-start and output slew rate
o Output voltage margining
o UV/OV monitoring of all outputs
o Enable/Disable outputs independently
The SMB110 integrates all the essential blocks required to
implement a complete five-channel power subsystem including
two synchronous step-down “buck” controllers, one step-up
“boost” controller, one inverting “buck-boost” controller and one
fixed output +3.3V LDO. Additionally sophisticated power
control/monitoring functions required by complex systems are
built-in. These include digitally programmable output voltage
set point, power-up/down sequencing, enable/disable,
margining and UV/OV/input/output monitoring on all channels.
• Five output channels
o Two synchronous step-down (buck) channels
o One step-up (boost) channel
o One inverting (buck-boost) channel
o One fixed output +3.3V LDO
• User friendly Graphical User Interface (GUI)
• +2.7V to +6.0V Input Range
• Highly accurate reference and output voltage (<0.5%)
The integration of features and built-in flexibility of the SMB110
allows the system designer to create a “platform solution” that
can be easily modified via software without major hardware
with Active DC Output Control (ADOC™) technology
• Undervoltage Lockout (UVLO) with hysteresis
• 800 kHz operating frequency
changes.
Combined with the re-programmability of the
SMB110 this facilitates rapid design cycles and proliferation
• 96 bytes of user configurable nonvolatile memory
from a base design to future generations of product.
Applications
The SMB110 is suited to battery-powered applications with an
input range of +2.7V to +6.0V. Output voltages are extremely
accurate (<0.5%) employing proprietary ADOC™ technology.
Communication is via the industry standard I2C bus. All user-
programmed settings are stored in non-volatile EEPROM of
which 96 bytes may be used for general-purpose memory
applications. The operating temperature range is +0C to +70C
and the available package is a lead-free, Green, RoHS
compliant, 32-pad QFN-32.
• Digital camcorders/still cameras
• Portable DVD/MP3/GPS
• Camera/smart phones
• TFT Displays/Monitors/TV’s
• Mobile Computing/PDA’s
• Consumer battery-operated equipment
SIMPLIFIED APPLICATIONS DRAWING
SMB110
+3.3V @20mA
LDO
MCU/RTC
CCD
+2.7V to +6.0V
or
Li-Ion
Inverter
Channel
-0.8V to -30V (Prog.) @UP TO1A
Vin to +30V (Prog.) @ UP TO 1A
+0.8V to 0.9 x Vin (Prog.) @ 2A
Step-Up
(Boost)
TFT/LCD
I2C/SMBus
Channels
System
Control and
Monitoring
Memory, I/O
Reset Input
2 Step-
Down
Reset Output
Power Good
(Buck)
Channels
+0.8V to 0.9 x Vin (Prog.) @ 2A
CPU Core
Figure 1 – Applications diagram featuring the SMB110 five-
Note: This is an applications example only. Some pins, components and values are not shown.
© SUMMIT Microelectronics, Inc. 2005
1717 Fox Drive • San Jose CA 95131 •
http://www.summitmicro.com/
2099 2.3 5/3/2005
Phone 408 436-9890 • FAX 408 436-9897
1
SMB110
Preliminary Information
Monitoring ..................................................................... 21
Output Voltage.............................................................. 21
LDO Standby Voltage ................................................... 22
Soft Start....................................................................... 22
Power-On Sequencing FlowChart ................................ 23
Minimum Load .............................................................. 24
Margining ...................................................................... 24
Application Schematic................................................... 25
Bill of materials.........................................................26-27
Programming information
TABLE OF CONTENTS
General Description ........................................................ 3
Typical Application.......................................................... 4
Internal Block Diagram.................................................... 5
Pin Descriptions...........................................................6-8
Package and Pin Configuration ...................................... 9
Absolute Maximum Ratings.......................................... 10
Recommended Operating Conditions........................... 10
DC Operating Characteristics..................................10-13
AC Operating Characteristics .................................14-15
I2C 2-Wire Serial Interface AC Operating Characteristics-
100khz........................................................................... 16
Timing Diagrams: I2C.................................................... 16
Efficiency Graphs.......................................................... 17
Transient Response...................................................... 18
Timing Diagrams: Power-On Sequence ....................... 19
Applications Information: Device Operation
Development Hardware & Software ............................. 28
Serial Interface.............................................................. 29
Write.............................................................................. 29
Read.............................................................................. 29
Configuration Registers ................................................ 29
General Purpose Memory............................................. 29
GUI................................................................................ 30
I2C memory read and writes ......................................... 31
Default Configuration Register Setting .....................32
Part Marking.................................................................. 33
Package........................................................................ 34
Ordering Information..................................................... 35
Legal Notice.................................................................. 35
Power Supply................................................................ 20
Enable........................................................................... 20
Power-On Sequencing.................................................. 20
Normal Sequencing ...................................................... 20
Sequencing With Enable............................................... 20
Sequencing with channel bypass ................................. 21
Manual Mode ................................................................ 21
Summit Microelectronics, Inc
2099 2.3 5/3/2005
2
SMB110
Preliminary Information
GENERAL DESCRIPTION
The SMB110 is a fully programmable DC-DC controller
that monitors, margins, and cascade sequences. It has 5
voltage outputs, consisting of: two synchronous “buck”
step-down controllers, one “boost” step-up controller,
one “boost-buck” negative DC-DC controller, and one
LDO.
four unique sequence positions. During sequencing each
channel in a given sequence position is guaranteed to
reach its programmed output voltage before the
channel(s) occupying the next sequence position initiate
their respective soft-start sequence.
A
unique
programmable delay exists between each power on/off
sequence position. In addition to power on/off
sequencing all supplies can be powered on/off
individually through an I2C command or by assertion of
an enable pin.
The SMB110 uses a fixed 800 kHz Pulse Width
Modulation (PWM) control circuit. A type three voltage
mode compensation network is used offering a cost
effective solution without compromising the transient
response. By utilizing external n and p–type MOSFET
transistors the efficiency and load current can be
customized to fit a wide array of system requirements.
The SMB110 integrates two buck outputs that are
capable of producing an output voltage less than the
input voltage. Each buck output voltage is set by an
internal resistor divider and a programmable voltage
reference. The integrated resistor divider eliminates the
cost and space necessary for external components and
has several programmable values. Through the
programmability of the reference and the resistor divider,
practically any output voltage less than the battery can
be produced without the need to change external
components.
In addition, the SMB110 integrates one boost output
capable of producing an output voltage greater than the
input voltage. The boost topology is asynchronous, using
a rectifying Schottky diode and eliminating the need for
an additional external MOSFET driver. An external p-
channel sequencing MOSFET’s accompanies the boost
channel in order to isolate the switching MOSFET from
the battery when disabled.
The SMB110 also contains one inverting buck-boost
output capable of producing a negative output voltage
less than or greater than, the input voltage. The buck
boost output is asynchronous and drives an external p-
channel MOSFET.
Each output voltage is monitored for under-voltage and
over-voltage (UV/OV) conditions, using a comparator-
based circuit where the output voltage is compared
against an internal programmable reference. An
additional feature of the output voltage monitoring is a
programmable glitch filter capable of digitally filtering a
transient OV/UV fault condition from a true system error.
When a fault is detected for a period in excess of the
glitch filter, all supplies may be sequenced down or
immediately disabled and one of two output status pins
can be asserted. The current system status is always
accessible via internal registers containing the status of
all four channels.
The SMB110 possesses an Undervoltage Lockout
(UVLO) circuit to ensure the SMB110 will not power up
until the battery voltage has reached a safe operating
voltage. The UVLO function exhibits hysteresis, ensuring
that noise or a brown out voltage on the supply rail does
not inadvertently lead to a system failure.
The SMB110 provides margining control over all of its
output voltages. Through an I2C command, all outputs
can be margined to any voltage setting within the
nominal output voltage rage. Margining creates three
pre-programmed settings that each channel can be set
to via an I2C command. Margining is ideal when used
with the boost channel configured as an LED driver
where margining provides three brightness settings.
In addition, each output is slew rate limited by soft-start
circuitry that is user programmable and requires no
external capacitors.
All programmable settings on the SMB110 are stored in
non-volatile registers and are easily accessed and
modified over an industry standard I2C serial bus. For
fastest prototype development times Summit offers an
evaluation card and a Graphical User Interface (GUI).
A Low DropOut linear regulator with fixed 3.3 volt output
provides
a
low current supply for “always on”
microcontrollers. The LDO has a special input supply
that is internally multiplexed between the LDO supply pin
and the battery. This ensures that the LDO will always
be active over the recommended operating voltages
(2.7V – 6.0V).
The SMB110 is capable of power-on/off cascade
sequencing where each channel can be assigned one of
Summit Microelectronics, Inc
2099 2.3 5/3/2005
3
SMB110
Preliminary Information
TYPICAL APPLICATION
+2.7 to +6.0V
SMB110
VBATT
HVSUP3
VDDCAP
GND
HSDRV_CH3
+0.8V to 0.9 x VIN @ 2A
DRVGND
LSDRV_CH3
SDA
VM_CH3
SCL
COMP1_CH3
nRESET
HEALTHY
COMP2_CH3
PWREN0
HVSUP2
HOST_RESET
HSDRV_CH2
-0.8V to -10 x VIN @ UP TO 1A
+0.8V to 0.9 x VIN @ 2A
LSDRV_CH0
COMP1_CH0
LSDRV_CH2
COMP2_CH0
VM_CH2
COMP1_CH2
VREFOUT
COMP2_CH2
PCHSEQ_CH1
3.3V @ 20mA
1.1 x VIN to 10 xVIN @ UP TO 1A
VSTANDBY
LDO_SUPPLY
LSDRV_CH1
COMP1_CH1
COMP2_CH1
Figure 2 – Typical application schematic showing external circuitry necessary to configure the SMB110
channels as: step-up, step-down, and inverting outputs
Summit Microelectronics, Inc
2099 2.3 3/1/2005
4
SMB110
Preliminary Information
INTERNAL BLOCK DIAGRAM
HVSUP[2,3]
HSDRV[2,3]
COMP2_CH[2,3]
VM_CH[2,3]
Channel 2 and 3
Synchronous buck
PWM Converter
100k
z
–
+
DUTY
CYCLE
LIMIT
+
–
OA
z
z
DEADTIME
MAX LIMIT
CLAMP
OSC
Fixed 800kHz
LOW LIMIT
COMP1_CH[2,3]
+
–
z
z
OVER VOLTAGE
GLITCH
FILTER
LSDRV[2,3]
PWREN0
DETECTION
VREF
LEVEL
SHIFTER
SEQUENCING
LOGIC
DIGITAL TO
ANALOG
+
–
UNDER VOLTAGE
DETECTION
GLITCH
FILTER
ENABLE
CONVERTER
ENABLE
ENABLE
VREF
Channel 1
boost
COMP2_CH1
PWM Converter
with Shutoff
–
+
DUTY
CYCLE
LIMIT
OA
+
–
z
z
VDD_CAP
PCHSEQ_CH1
MAX LIMIT
CLAMP
OSC
Fixed 800kHz
LOW LIMIT
LSDRV1
COMP
+
–
COMP1_CH1
z
DRIVER
z
z
+
–
OVER VOLTAGE
GLITCH
FILTER
DETECTION
LEVEL
100u
0.2 V
SHIFTER
+
–
UNDER VOLTAGE
DETECTION
GLITCH
FILTER
I2C/SMBUS
VREF
Channel 0
Negative
SDA
SCL
PWM Converter
–
+
z
LSDRV0
DUTY
CYCLE
LIMIT
z
+
–
OA
DRIVER
z
MAX LIMIT
CLAMP
OSC
COMP1_CH0
COMP2_CH0
Fixed 800kHz
LOW LIMIT
z
–
+
GLITCH
FILTER
OVER VOLTAGE
VREF_OUT
X2
DETECTION
LEVEL
LEVEL
SHIFTER
SHIFTER
–
+
UNDER VOLTAGE
DETECTION
GLITCH
FILTER
VREF
VREF
LDO_SUPPLY
Channel 5
Standby Series-Pass LDO
VSTANDBY
GND
LDO
VBATT
z
z
z
z
BANDGAP
VREF
nBATT_FAULT
z
+
–
VDD_CAP
2.5V
UV2
z
REGULATOR
z
D
Q
+
–
LEVEL
SHIFTER
UV1
Summit Microelectronics, Inc
2099 2.3 3/1/2005
5
SMB110
Preliminary Information
PIN DESCRIPTIONS
Pin Number Pin Type
Pin Name
Pin Description
The HEALTHY pin is an open drain output. High when all
enabled output supplies are within the programmed levels.
HEALTHY will ignore any disabled supply.
There is a
1
OUT
HEALTHY
programmable glitch filter on the under-voltage and over-voltage
sensors so that short transients outside of the limits will be
ignored by HEALTHY. When used this pin should be pulled high
by an external pull-up resistor.
SDA (Serial Data) is an open drain bi-directional pin used as the
2
3
I/O
IN
SDA
SCL
I2C data line. SDA must be tied high through a pull-up resistor.
SCL (Serial Clock) is an open drain input pin used as the I2C
clock line. SCL must be tied high through a pull-up resistor.
The VREF_OUT (Voltage Reference) pin is a precision
reference output. When an inverting output is used, this pin acts
as a level shifting reference for the feedback circuitry. When the
inverting output is not used, this pin may be used as a
programmable reference.
4
OUT
VREF_OUT
COMP1_CH0 (Channel 0 primary Compensation) pin is the
5
6
IN
IN
COMP1_CH0
COMP2_CH0
primary feedback input of the inverting controller.
COMP2_CH0 (Channel 0 secondary Compensation) pin is the
second feedback input of the inverting controller
The LSDRV_CH0 (Channel 0 Low-side Driver) pin is the
switching node of the inverting buck-boost controller. The output
of this pin should be attached to the gate of an external p-
channel MOSFET driver.
7
8
OUT
IN
LSDRV_CH0
The HOST_RESET pin is an active high reset input. When this
pin is asserted high, the nRESET output will immediately go low.
When HOST_RESET is brought low, nRESET will go high after
a programmed reset delay.
HOST_RESET
The VBATT_CAP (VBATT Capacitor) pin is an external
9
CAP
VBATT_CAP
VBATT
capacitor input used to filter the internal supply.
Power supply to part.
10
PWR
The PCHSEQ_CH1 (Channel 1 Sequence) pin is attached to an
external p-channel MOSFET and is used to enable the
corresponding channel 1 boost controller. PCHSEQ_CH1 uses
an internal 100µA current sink for sequencing. This pin should
be pulled high through a parallel RC connection.
11
OUT
PCHSEQ_CH1
The COMP1_CH1 (Channel 1 primary Compensation) pin is the
primary compensation input of the channel 1 boost controller.
The COMP2_CH1 (Channel 1 secondary Compensation) pin is
the second compensation input of the channel 1 boost
controller.
12
13
IN
IN
COMP1_CH1
COMP2_CH1
Summit Microelectronics, Inc
2099 2.3 3/1/2005
6
SMB110
Preliminary Information
PIN DESCRIPTIONS
Pin Number Pin Type
Pin Name
Pin Description
The nRESET (Reset) pin is an active low open drain output. Active
when the SMB110 is powered up. Remains low for a user
programmable period of 25, 50, 100, or 200 ms after all enabled
supplies have exceeded their programmed thresholds. When used,
this pin should be pulled high by an external pull up resistor.
14
OUT
nRESET
DRVGND (Driver Ground). Each DRVGND pin should be attached
15
16
PWR
OUT
DRVGND
externally to ground through a short wide wire.
The LSDRV_CH1 (Channel 1 Low-side Driver) pin is the lower
switching node of the synchronous boost controller. This pin attaches
to an external n-channel MOSFET
LSDRV_CH1
The LSDRV_CH2 (Channel 2 Low-side Driver) pin is the lower
switching node of the channel 2 synchronous buck controller. Attaches
to the gate of n-channel MOSFET.
17
18
OUT
LSDRV_CH2
HVSUP2
PWR
Supply for Channel 2 buck driver.
The HSDRV_CH2 (Channel 2 High-side Driver) pin is the upper
switching node of the channel 2 synchronous buck controller. Attach to
the gate of p-channel MOSFET. A delay exists between the assertion
of HSDRV_CH2 and assertion of LSDRV_CH2 to prevent excessive
current flow during switching.
19
OUT
HSDRV_CH2
The COMP2_CH2 (Channel 2 secondary Compensation) pin is the
secondary compensation input of the channel 2 buck controller.
The COMP1_CH2 (Channel 2 primary Compensation) pin is the
primary compensation input of the channel 2 buck controller. Each pin
is internally connected to a programmable resistor divider.
The VM_CH2 (Channel 2 Voltage Monitor) pin connects the channel 6
controller output. Internally the VM_CH2 pin connects to an internal
programmable resistor divider.
20
21
IN
IN
COMP2_CH2
COMP1_CH2
22
23
IN
VM_CH2
The LDO_ SUPPLY pin powers the 3.3V VSTANDBY LDO output. The
LDO_ SUPPLY pin should be connected to the output of a boost
output (usually the intermediate bus). When the battery voltage drops
below the UV1 threshold, this pin will no longer supply the LDO. Do
not apply a voltage in excess of the recommended input voltage to this
pin.
PWR
LDO_SUPPLY
The VSTANDBY (Voltage Standby) pin is a 3.3V LDO output.
VSTANDBY is supplied from the output of the intermediate bus
through the LDO_SUPP pin. When PWR_FAIL is asserted an internal
analog multiplexer will power VSTANDBY directly from the VBATT pin.
24
OUT
VSTANDBY
The LSDRV_CH3 (Channel 3 Low-side Driver) pin is the lower
switching node of the channel 3 synchronous buck controller. Attaches
to the gate of n-channel MOSFET.
25
26
OUT
LSDRV_CH3
HVSUP3
PWR
Supply for Channel 3 buck driver.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
7
SMB110
Preliminary Information
PIN DESCRIPTION
Pin Number
Pin Type Pin Name
Pin Description
The HSDRV_CH3 (Channel 3 High-side Driver) pin is the upper
switching node of the channel 3 synchronous buck controller. Attach
HSDRV_CH3 to the gate of p-channel MOSFET. A delay exists between the
assertion of HSDRV_CH3 and assertion of LSDRV_CH3 to prevent
excessive current flow during switching.
27
OUT
The PWREN0 (Power Enable 0) pin is a programmable input used to
28
29
30
IN
IN
IN
PWREN0
enable (disable) selected supplies. When unused this pin should be
tied to a solid logic level.
The COMP2_CH3 (Channel 3 secondary Compensation) pin is the
secondary compensation input of the channel 3 buck controller.
The COMP1_CH3 (Channel 3 primary Compensation) pin is the
COMP2_CH3
COMP1_CH3 primary compensation input of the channel 3 buck controller. Each
pin is internally connected to a programmable resistor divider.
The VM_CH3 (Channel 3 Voltage Monitor) pin connects the channel
31
IN
VM_CH3
3 controller output. Internally the VM_CH3 pin connects to an internal
programmable resistor divider.
The GND pin should be connected to the common ground plane
32
PWR
PWR
GND
GND
through a short fat wire.
PAD
The exposed metal pad should be attached to ground.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
8
SMB110
Preliminary Information
PACKAGE AND PIN DESCRIPTION
Top view
SMB110
5mm x 5mm QFN-32
32
31
30
29
28
27
26
25
VSTANDBY
LDO_SUPPLY
VM_CH2
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
HEALTHY
SDA
SCL
VREF_OUT
COMP1_CH0
COMP2_CH0
LSDRV_CH0
HOST_RESET
COMP1_CH2
COMP2_CH2
GND
HSDRV_CH2
HVSUP2
LSDRV_CH2
9
10
11
12
13
14
15
16
Summit Microelectronics, Inc
2099 2.3 3/1/2005
9
SMB110
Preliminary Information
ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING CONDITIONS
Commercial Temperature Range............... 0°C to +70°C
VBATT Supply Voltage ..............................2.7V to +6.0V
HVSUP Supply Voltage..............................2.7V to +6.0V
LDO_SUPPLY...........................................GND to +6.0V
All Others.................................................GND to VBATT
Package Thermal Resistance (θJA)
Temperature Under Bias .................... -55°C to +125°C
Storage Temperature.......................... -65°C to +150°C
Terminal Voltage with Respect to GND:
VBATT Supply Voltage ................... -0.3V to +6.5V
HVSUP Supply Voltage.................. -0.3V to +6.5V
LDO_SUPPLY ................................ -0.3V to +6.5V
All Others ...................................... -0.3V to VBATT
Output Short Circuit Current .................…………100mA
Reflow Solder Temperature (30 secs)................. 260°C
Junction Temperature.......................................... 150°C
ESD Rating per JEDEC....................................... 2000V
Latch-Up testing per JEDEC.............................±100mA
32 Lead QFN. ………..……………..……………...…TBD
Moisture Classification Level 3 (MSL 3) per J-STD- 020
RELIABILITY CHARACTERISTICS
Data Retention ................................................. 100 Years
Endurance..................................................100,000 Cycle
Temperature Range
0°C to +70°C
Note - The device is not guaranteed to function outside its operating rating. Stresses listed under Absolute Maximum
Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions outside those listed in the operational sections of the specification is not implied.
Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Devices
are ESD sensitive. Handling precautions are recommended.
DC OPERATING CHARACTERISTICS
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Input supply voltage
VBATT
Input supply voltage
2.7
6.0
V
(operational)
Internally multiplexed with
VBATT
Gate drive voltage
VBATT rising
VLDO_SUPP
VHVSUP
VUVLO
Linear regulator supply voltage
Buck driver supply voltage
Undervoltage lockout
2.7
2.7
6.0
6.0
V
V
V
2.2
2.0
VBATT falling
All voltage inputs monitored.
No supplies switching,
VBATT at 4.2V, LDO on with
no output enabled
IDD-MONITOR
Monitoring current
330
µA
Switching current for one output
enabled
Current drawn when one
ISD
mA
1.2
output enabled
Total current all channels
VBATT at 4.2V, LDO on with
no load
IDD-
2.2
mA
V
switching.1
VREF(INT)
Oscillator
fOSC
∆fOSC
OPP
Internal voltage reference
0.995
-10
1.005
Oscillator frequency
800
kHz
%
V
Oscillator frequency accuracy
Oscillator peak to peak2 voltage
Frequency stability for voltage
+10
1
0.1
∆fSV
%/V
Frequency stability for
∆fST
%/°C
0.04
temperature
Summit Microelectronics, Inc
2099 2.3 3/1/2005
10
SMB110
Preliminary Information
DC OPERATING CHARACTERISTICS (CONTINUED)
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Error Amplifier
VACC
Threshold Voltage accuracy
Temperature stability
Open loop voltage Gain
Frequency bandwidth
Output source current
Output sink current
%
%
dB
MHz
µA
µA
0.2
0.2
60
30
20
TS
AVOL
BW
At DC
At AV=0 dB
At 0.5V
ISOURCE
ISINK
At 0.5V
800
LDO
LDO_SUPPLY = 4.2V,
VOUT
Nominal output voltage
Output voltage accuracy
V
3.3
0.3
ILOAD=0A
Percent of 3.3V output @
∆VOUT
%
10mA, LDO_SUPPLY = 4.2V
∆VLOAD
∆VLINE
PSRR
IQ
Load regulation error
Line regulation error
Power supply rejection ratio
Quiescent current
%/V
%/mA
dB
0.3
0.17
50
50
20
100
200
300
400
No load
20log(Vout/Vin) @ 10kHz
VBATT = 4.2V, ILOAD=0A
IOUT = 1 mA
IOUT = 5 mA
IOUT = 10 mA
µA
VDO
Dropout voltage
mV
IOUT = 15 mA
IOUT = 20 mA
ILIMIT
VN
Maximum output current
Output Noise voltage
40
mA
mV
Peak to peak
1
Inverting Output Block Channel 0
Programmable voltage set point
VOUT
VBATT=4.2V, ILOAD=0
V
-35
-0.5
range
Excluding external resistor
divider accuracy
COMP1 pin
∆VOUT
Output accuracy
Feedback voltage reference
%
V
0.5
1.0
VCOMP1
∆ VCOMP1
Feedback voltage reference
COMP1 pin
%
-0.2
+0.2
accuracy
ROH
ROL
High
Low
17
3
RON
LSDRV Output ON resistance
LSDRV Duty Cycle
Ω
%
V
85
5
95
15
D.C.
VREF_OUT pin programmable
VREF_OUT
Level shift voltage reference
1
2
in 8mV steps
Summit Microelectronics, Inc
2099 2.3 3/1/2005
11
SMB110
Preliminary Information
DC OPERATING CHARACTERISTICS (CONTINUED)
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Inverting Output Block Channel 0 (Continued)
IREF_OUT
ML
VREF_OUT source current
Minimum load3
VREF_OUT = 1.5V
µA
kΩ
100
L=33uF, VO=-7.5V,
10.1
VIN=4.2V, VD=0.3V
Boost Output Block Channel 1
Programmable voltage set point
VOUT
VBATT=4.2V, ILOAD=0
4.5
35
V
%
Ω
range
Excluding external resistor
divider accuracy
Output high
Output low
High
∆VOUT
RDRVH
Output accuracy
0.5
17
3
HSDRV ON resistance
Duty Cycle
85
5
95
15
D.C.
%
Low
COMP1 pin
Programmable in 4mV steps
VCOMP1
Feedback voltage reference
V
1.0
Feedback voltage reference
accuracy
Minimum load4
∆VCOMP1
COMP1 pin
-0.5
50
+0.5
100
%
L=33uF, VO=12V, VIN=4.2V,
VD=0.3V
ML
29
kΩ
µA
IPCHSEQ
PCHSEQ sink current
Voltage on PCHSEQ pin
when LSDRV output is
enabled
ENTH
Enable threshold
200
mV
Buck Output Block Channels 2 and 3
VBATT = 4.2V, ILOAD = 0
VBATT = 6.0V, ILOAD = 0
0.5
0.6
3.8
5.4
VOUT
Voltage nominal set point range
V
%
Ω
Including internal resistor
∆VOUT
RDRVH
Output accuracy
0.5
divider
Output high
Output low
8
8
HSDRV ON resistance
Output high
Output low
17
3
RDRVL
LSDRV ON resistance
COMP1 pin
Programmable in 4mV steps
VCOMP1
∆VCOMP1
D.C.
Feedback voltage reference
V
mV
%
1.0
Feedback voltage reference
accuracy
COMP1 pin
-0.5
+0.5
High
Low
85
5
95
15
Duty Cycle
Summit Microelectronics, Inc
2099 2.3 3/1/2005
12
SMB110
Preliminary Information
DC OPERATING CHARACTERISTICS (CONTINUED)
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Miscellaneous
VIH
VIL
VOL
IOL
Input high voltage
Input low voltage
Open drain outputs
Output low current
0.9xVDD_CAP
0.1xVDD_CAP
V
V
V
ISINK = 1mA
0
0
0.4
1.0
mA
Programmable Monitoring Thresholds
Programmable UV1
threshold voltage
Programmable UV1
V
VPUV1
2.55
-20
3.60
+20
3.60
+20
threshold
measured on VBATT pin
in 150 mV increments
∆VPUV1
VPUV2
UV1 accuracy
mV
V
Programmable UV2
threshold voltage
Programmable UV2
threshold
2.55
-20
measured on VBATT pin
in 150 mV increments
∆VPUV2
UV2 accuracy
mV
%
-5
For channels 1-3.
Relative to nominal set
point voltage
Programmable under
voltage threshold
-10
-15
-20
PUVTH
+5
For channels 1-3.
Relative to nominal set
point voltage
Programmable over voltage
threshold
+10
+15
+20
%
%
POVTH
-6.2
-12.4
-18.6
-24.8
+6.2
Programmable under
voltage threshold5
For channel 0. VO=-7.5V,
R1=392K, R2=33.2K
PUVTH
+12.4
+18.6
+24.8
Programmable over voltage
threshold6
For channel 0. VO=-7.5V,
R1=392K, R2=33.2K
%
POVTH
Summit Microelectronics, Inc
2099 2.3 3/1/2005
13
SMB110
Preliminary Information
AC OPERATING CHARACTERISTICS
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Parameter
Conditions
Min
1.3
Typ
1.5
12.5
25
Max
1.7
Unit
10.6
21.3
42.5
1.3
14.4
28.8
57.5
1.7
Programmable power-On Programmable
power-On
sequence
tPPTO
ms
sequence timeout period. position to sequence position delay.
50
1.5
12.5
25
10.6
21.3
42.5
21.3
42.5
85
14.4
28.8
57.5
28.8
57.5
115
230
Programmable power-off
Programmable power-off sequence
tDPOFF
ms
ms
sequence timeout period. position to sequence position delay.
50
25
Programmable time following assertion of
50
Programmable reset
last supply before nRESET pin is released
tPRTO
time-out delay
high.
100
200
OFF
50
170
Time between active enable in which
corresponding outputs must exceed there
42.5
85
57.5
115
230
Programmable sequence
programmed under voltage threshold. If
termination period
tPST
ms
exceeded, a force shutdown will be
100
200
0
initiated.
170
Period for which fault must persist before
Programmable glitch filter fault triggered actions are taken. Present
on all buck, boost, and inverting supplies.
tPGF
µs
6.8
340
170
85
8
9.2
460
230
115
76.7
57.5
38.3
28.8
23
400
200
100
66.7
50
56.7
42.5
28.3
21.3
17.0
Programmable slew rate
reference
Adjustable slew rate factor proportional to
output slew rate.
SRREF
V/s
33.3
25
20
Summit Microelectronics, Inc
2099 2.3 3/1/2005
14
SMB110
Preliminary Information
AC OPERATING CHARACTERISTICS (CONTINUED)
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
Symbol
Inverting Output Block Channel 0
HS Driver output rise time CG=100pF, VBATT=4.2V
HS Driver output fall time CG=100pF, VBATT=4.2V
Boost Output Block Channel 1
Parameter
Conditions
Min
Typ
Max
Unit
tRH
tFH
10
10
ns
ns
LS Driver output rise time CG=100pF, VBATT=4.2V
LS Driver output fall time CG=100pF, VBATT=4.2V
tRL
tFL
10
10
ns
ns
Buck Output Block Channels 2 and 3
LS Driver output rise time CG=100pF, VBATT=4.2V
LS Driver output fall time CG=100pF, VBATT=4.2V
HS Driver output rise time CG=100pF, VBATT=4.2V
tRL
tFL
10
10
15
5
ns
ns
ns
ns
tRH
tFH
HS Driver output fall time
CG=100pF, VBATT=4.2V
High to low transition on HSDRV
20
10
Driver non-overlap delay
tDT
ns
Low to high transition on buck HSDRV
1. The total current drawn when all supplies are switching will not equal the sum of the buck, boost, and inverting buck-boost channels current
consumption when switching independently. This is due to current overhead to commence sequencing.
2. Guaranteed by design.
3. The minimum load for the Inverting Boost-Buck channel is defined by the following equation: where VO = Programmed output voltage, VIN =P-
Channel MOSFET source voltage, L = inductance, Vd = forward diode drop (0.6V silicon, 0.3V Schottky). Lesser values may exist
2*L*Vout *(Vout - Vd)
Rmax =
VIN2*1.25E-8
4. The minimum load for Boost channels is defined by the following equation: where VO = Programmed output voltage, VIN =P-Channel MOSFET
source voltage, L = inductance, and Vd = forward diode drop (0.6V silicon, 0.3V Schottky. Lesser values may exist
2*L*Vout*(Vout - VIN + Vd)
Rmax =
VIN2*1.25E-8
5. The Channel 0 programmable under voltage setting is calculated from the following formula: where VREF_OUT is the voltage o the VREF_OUT
pin and R1 and R2 are the upper and lower resistors in the external voltage divider, n corresponds to the available user programmable settings
VREF_OUT -.95(1+R2/R1)
VREF_OUT - (1+R2/R1)
% n= 1,2,3,4
Ch 0 PUVTH = -100n 1 -
6. The Channel 0 programmable over voltage setting is calculated from the following formula: where VREF_OUT is the voltage o the VREF_OUT pin
and R1 and R2 are the upper and lower resistors in the external voltage divider, n corresponds to the available user programmable settings
VREF_OUT -.95(1+R2/R1)
VREF_OUT - (1+R2/R1)
n= 1,2,3,4
%
Ch 0 POVTH = 100n 1 -
Summit Microelectronics, Inc
2099 2.3 3/1/2005
15
SMB110
Preliminary Information
I2C-2 WIRE SERIAL INTERFACE AC OPERATING CHARACTERISTICS –100 kHz
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND.)
100kHz
Typ
Symbol
Description
Conditions
Min
0
4.7
4.0
Max Units
fSCL
TLOW
THIGH
SCL clock frequency
Clock low period
Clock high period
100
kHz
µs
µs
Before new transmission - Note
tBUF
Bus free time
4.7
µs
1/
tSU:STA
tHD:STA
tSU:STO
tAA
Start condition setup time
Start condition hold time
Stop condition setup time
Clock edge to data valid
4.7
4.0
4.7
0.2
µs
µs
µs
µs
3.5
SCL low to valid SDA (cycle n)
SCL low (cycle n+1) to SDA
tDH
Data output hold time
0.2
µs
change
tR
tF
tSU:DAT
tHD:DAT
TI
SCL and SDA rise time
SCL and SDA fall time
Data in setup time
Note 1/
Note 1/
1000
300
ns
ns
ns
ns
ns
ms
ms
250
0
Data in hold time
Noise filter SCL and SDA
Write cycle time config
Write cycle time EE
Noise suppression
Configuration registers
Memory array
100
tWR_CONFIG
tWR_EE
10
5
Note: 1/ - Guaranteed by Design.
TIMING DIAGRAMS
tWR (For Write Operation Only)
tHIGH
tLOW
tR
SCL
tSU:SDA
tF
tBUF
tHD:DAT
tSU:DAT
tSU:STO
tHD:SDA
SDA (IN)
tAA
tDH
SDA (OUT)
Figure 4 – I2C timing diagram
Summit Microelectronics, Inc
2099 2.3 3/1/2005
16
SMB110
Preliminary Information
EFFICIENCY GRAPHS
Channel 1 Boost 6.0V
Channel 0 Inverting -7.5V
Channel 1 Boost 12V
0.85
0.8
0.96
0.94
0.92
0.9
0.9
0.85
0.8
0.75
0.7
0.65
0.6
0.88
0.86
0.84
0.82
0.8
3.0V
3.3V
3.6V
3.8V
4.2V
3.0V
3.3V
3.6V
3.8V
4.2V
0.75
0.7
4.2V
3.8V
3.6V
3.0V
0.55
0.5
0.65
0.6
0.45
0.4
0.78
0
0.2
0.4
0.6
0.8
1
0
0.01
0.02
Current (Amps)
0.03
0.04
0
0.01
0.02
0.03
Current (Amps)
Channel 3 (Ch 1 Boost + Buck) 3.0 Volts
Current (Amps)
Channel 3 (Ch 1 Boost + Buck) 5.0 Volts
Channel 2 Buck 1.2V
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.9
0.95
0.85
0.8
0.9
0.85
0.8
3.0V
3.3V
3.6V
3.8V
4.2V
3.0V
3.3V
3.6V
3.8V
4.2V
3.0V
3.3V
3.6V
3.8V
4.2V
0.75
0.7
0.75
0.7
0.65
0.65
0.6
0.6
0.01
0
0.1
0.2
0.3
0.4
0.11
0.21
Current (Amps)
0.31
0
0.2
0.4
0.6
Current (Amps)
Current (Amps)
Channel 2 Buck 2.5 Volts
0.94
0.92
0.9
0.88
0.86
0.84
0.82
0.8
3.0V
3.3V
3.6V
3.8V
4.2V
0
0.1
0.2
0.3
Current (Amps)
Summit Microelectronics, Inc
2099 2.3 3/1/2005
17
SMB110
TRANSIENT RESPONSE
CHANNEL 2 BUCK TRANSIENT
RESPONSE
CHANNEL 2 BUCK TRANSIENT
RESPONSE
VSU
VSU
AC-COUPLED
AC-COUPLED
50mV/div
50mV/div
0V
0A
0V
0V
ISD
ISD
100mA/div
100mA/div
0A
VIN = 4.2V VOUT = 1.2V
VIN = 4.2V VOUT = 2.5
200 us/div
200 us/div
CHANNEL 3 BUCK TRANSIENT
RESPONSE
CHANNEL 3 BUCK TRANSIENT
RESPONSE
VSU
VSU
AC-COUPLED
AC-COUPLED
50mV/div
0V
50mV/div
ISD
ISD
0A
0A
200mA/div
100mA/div
V
IN = 4.2V VOUT = 3.0V
VIN = 4.2V VOUT = 5.0V
200 us/div
200 us/div
CHANNEL 0 INVERTING TRANSIENT
RESPONSE
CHANNEL 1 STEP UP TRANSIENT
RESPONSE
VSU
VSU
AC-COUPLED
50mV/div
0V
AC-COUPLED
0V
0A
50mV/div
ISD
ISD
10mA/div
5mA/div
0A
VIN = 4.2V VOUT = -7.5V
200 us/div
VIN = 4.2V VOUT = 12V
200 us/div
Summit Microelectronics, Inc
2099 2.3 3/1/2005
18
SMB110
Preliminary Information
TIMING DIAGRAMS: POWER-ON SEQUENCE
SEQUENCE POSITION
0
1
2
3
4
VBATT
VSTANDBY
PWREN0 OR
I2C ENABLE
Sequence Delay
INTERMEDIATE
BOOST
PWREN0 OR
I2C ENABLE
STEP-UP,STEP-DOWN,
OR INVERTING
OUTPUT
PWREN0 OR
I2C ENABLE
STEP-UP,STEP-DOWN,
OR INVERTING
OUTPUT
PWREN0 OR
I2C ENABLE
STEP-UP,STEP-DOWN,
OR INVERTING
OUTPUT
tRESET
TIMEOUT
HEALTHY
nRESET
Figure 5 – SMB110 power-On sequence. Any PWM channel may be enabled or disabled through an I2C
command or by the PWREN0 pin.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
19
SMB110
Preliminary Information
APPLICATIONS INFORMATION
DEVICE OPERATION
enable, and sequencing with channel bypass. In
addition, each channel may be powered on in a manual
mode, independent of the sequence position. The
power-on sequencing mode selection is programmable
over the I2C bus and stored in the non-volatile memory.
POWER SUPPLY
The SMB110 can be powered from an input voltage
between 2.7-6.0 volts applied between the VBATT pin
and ground. The input voltage applied to the VBATT pin
is internally regulated and used as an internal VBATT
supply. The VBATT pin is monitored by an
UnderVoltage Lockout (UVLO) circuit, which prevents
the device from turning on when the voltage at this
node is less than the UVLO threshold.
NORMAL CASCADE SEQUENCING
During Normal Sequencing, the sequence position
counter is initialized to the first sequence position
(position 1), each channel occupying this position then
waits an individual programmable timeout period (tPPTO
)
POWER-ON/OFF CONTROL
of 1.5, 12.5, 25, or 50 ms. Once enabled, all channels
occupying the first sequence position will begin a soft-
start. As the output voltage of the channel is ramped
up, it is monitored by a comparator based, user
programmable, under-voltage threshold sensor. After
this threshold is exceeded, indicating that the selected
channel(s) have reached their nominal operating range
the sequence position counter is incremented, and fault
monitoring begins for that channel. Once all channels
occupying the first sequence position have surpassed
their under-voltage thresholds, the power-on delay for
the next sequence position will begin. This process
continues until all channels have been sequenced on
and are above their under-voltage threshold.
The outputs on the SMB110 can be turned on in one of
three ways: first a general purpose enable input pin
PWREN0, second an I2C Power on command can be
issued, or third if a programmable bit is set to initiate
the power on process when the UVLO threshold is
exceeded. a restart will only occur if the power-on pin is
toggled or an I2C Power on command is issued.
ENABLE
Once a power on command has been issued, the
power on process can be controlled by means of an
enable signal. Each channel can be controlled by one
of four enable signals and the assignment type can be
mixed and matched for each of the four channels. The
enable signal can stall the power-on process until the
enable is valid, or disable a controller once all supplies
have been enabled. There are two ways to generate
the enable signal; the first approach allows the enable
signal to be assigned the PWREN0 pin, and the second
approach allows the enable to be controlled by the
contents of a volatile register that can be written to at
any time. This volatile register will be automatically
initialized once the UVLO threshold has been exceeded
to a known programmed state.
SEQUENCING WITH ENABLE
During the Sequencing With Enable mode, sequencing
commences as with the Normal Sequencing, except
that prior to a channel beginning to soft-start, the
enable corresponding to that channel must be asserted.
In the event that the enable is not asserted, sequencing
will halt indefinitely until a valid enable is provided.
Once a valid enable is provided, a soft-start function will
begin for that channel. This process will continue until
all channels occupying the first sequence position are
above their under-voltage settings, at which point the
sequence position counter will be incremented.
POWER-ON SEQUENCING
Each channel on the SMB110 may be placed in any
one of four unique sequence positions. To provide
programmable order, the SMB110 navigates between
these sequence positions using a feedback-based
cascade-sequencing circuit. Cascade sequencing is the
process in which each channel is continually compared
against a programmable reference voltage until the
voltage on the monitored channel exceeds the
reference voltage, at which point an internal sequence
position counter is incremented and the next sequence
position is entered.
SEQUENCING WITH CHANNEL BYPASS
When the Sequencing With Channel Bypass mode is
selected, sequencing will commence as with the
Sequencing With Enable, except that if the enable
signal is not asserted by the end of the power-on delay
period, that channel will be bypassed. If no other
channels occupy the current sequence position, the
sequence position counter will be incremented
beginning the power-on delay for all channels in the
next sequence position. Once a channel has been
bypassed, it may still be enabled any time prior to a
power off operation.
Once power-on sequencing has been initiated,
automated sequencing may commence in one of three
ways (Figure 7): normal sequencing, sequencing with
Summit Microelectronics, Inc
2099 2.3 3/1/2005
20
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
MANUAL MODE
SMB110 are user programmable and may be set to
either 0 or 8 µs.
The SMB110 also provides a manual power-on mode in
which each channel may be enabled individually
irrespective of the state of other channels. In this mode,
the enable has complete control over the channel, and
all sequencing is ignored. In Manual mode channels will
not be disabled in the event of a fault.
In the event that one or more channels violate their
respective UV/OV setting for a period exceeding that
specified by the glitch filter, all channels (not set to
Manual mode) can optionally be powered off and-or,
the healthy pin can be triggered. The programmable
power off conditions that may result from a threshold
violation include the immediate power off all supplies
(force-shutdown) or the sequence of all supplies off.
Monitoring is accomplished by a comparator-based
approach, in which a programmable voltage reference
is compared against the monitored signal. Each
channel possesses a dedicated reference voltage
generated by a programmable level shifting digital to
analog converter. Each of which can be set from 0-1.0
volts in 4mV increments.
POWER OFF OPTIONS
FORCE-SHUTDOWN
When a battery fault occurs, a UV or OV is detected on
any PWM channel, or an I2C force-shutdown command
is issued, all channels will be immediately disabled.
SEQUENCE TERMINATION TIMER
At the beginning of each sequence position, an internal
programmable timer will begin to time out. When this
timer has expired, the SMB110 will automatically
perform a force-shutdown operation. This timer is user
BATTERY MONITORING
programmable with
a
programmable sequence
The battery voltage is monitored for two user
termination period (tPST) of 50,100,200 ms; this function
can also be disabled.
programmable UV settings via the VBATT pin
The SMB110 contains two user programmable voltage-
monitoring levels, UV1 and UV2. Battery voltage, like
all monitored voltages, is compared against a user
programmable voltage set internally by a digital to
analog converter.
Once the voltage on the VBATT pin has fallen below
either of the programmable under voltage set points the
SMB110 can be programmed to respond in one of
three ways, it can perform: a power-off operation, a
force-shutdown operation, or take no action. When
programmed to perform a power-off or force-shutdown
operation the SMB110 can optionally be programmed
to latch the outputs off until an I2C power-on command
is issued or immediately restart once the UV condition
has been removed.
POWER OFF SEQUENCING
The SMB110 has a power-off sequencing operation.
During a power off operation the supplies will be
powered off in the reverse order they where powered
on in. During the power off sequencing, all enables are
ignored.
When a power-off command is issued the SMB110 will
set the sequence position counter to the last sequence
position and disable that channel without soft-start
control; once off, the power off delay for the channel(s)
in the next to last sequence position will begin to
timeout, after which that channel(s) will be disabled.
This process will continue until all channels have been
disabled and are off. The programmable power-off
sequence timeout period (tDPOFF) can be set to 1.5,
12.5, 25, or 50 ms.
OUTPUT VOLTAGE
The PWM output voltages are set by a resistor divider
from the output to the COMP1 node; see Figure 6. For
the buck channels (Ch[2:3]), the voltage divider is
internal to the part and programmable. The resistor
divider may be set by adjusting a 100 kΩ resistor string
with 8 taps from R1 = 20-90 kΩ. For the boost output
(Ch1), the resistor divider is external and any
appropriate value of R1 an R2 can be chosen. The
reference voltage that sets the output is user
programmable, and may be set anywhere from 0-1.0V
in 4 mV increments for channels 1 to 3, channel 0 is
fixed at 1.0V. The Channel 0 inverting output is set by
the external resistor divider and the VREF_OUT
If a channel fails to turn off within the sequence
termination period, the sequence termination timer will
initiate a force shutdown, if enabled.
MONITORING
The SMB110 monitors all 4 PWM outputs for under-
voltage (UV) and over-voltage (OV) faults. The
monitored levels are user programmable, and may be
set at 5,10, 15, and 20 percent of the nominal output
voltage.
Each output possesses a glitch filter to ensure that
short violations in the UV or OV settings will not result
in a fault-triggered action. All glitch filters on the
Summit Microelectronics, Inc
2099 2.3 3/1/2005
21
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
voltage, which varies from 1.0 – 2.0V in 8 mV
SOFT START
increments
The SMB110 provides a programmable soft-start
function for all PWM outputs. The soft-start control
limits the slew rate that each output is allowed to ramp
up without the need for an external capacitor. The soft
start slew rate is proportional to the product of the
output voltage and a slew rate reference; see Figure 5.
This global reference is programmable and may be set
to 400,200,100,67,50,33,25, and 20 volts per second.
The slew rate control can also be disabled on any
channel not requiring the feature.
LDO STANDBY VOLTAGE
The SMB110 has an internal 3.3 volt Low Dropout
(LDO) linear regulator. While the battery voltage is
above the UV2 level this supply is powered from the
LDO_SUPPLY pin, however, when the battery voltage
drops below the UV2 level the LDO supply voltage will
be routed to the battery through an internal analog
multiplexer. The LDO will continue to be supplied by the
battery until the latched UV2 pin is released. The LDO
will be disabled once the Battery voltage falls below the
UV2 level.
Vout
VOUT
CHANNEL 0
CHANNELS 1 TO 3
R2
R2
COMP1
COMP1
–
–
+
+
1.0V
VREF
R1
R1
VREF_OUT
R1 AND R2 INTERNAL
FOR CHANNELS 2 AND 3
Figure 6: The output voltage is set by the resistor divider. The resistor divider is internal for all buck channels.
VREF is programmable from 0 to 1.0V in 4 mV increments and VREF_OUT is programmable from 1.0 to 2.0V in 8
mV increments. All voltage references are programmable via the I2C interface.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
22
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
R E S T A R T A F T E R P O W E R -
I 2
N
C
P O
W
E R
O
F F O R
O
C O
M
M
A N D
F O R C E - S H U T D O
W N
B E G I N
S E Q U E N C I N G
S E Q U E N C E
P O S I T I O
N 1
C U R R E N T
S E Q U E N C E
P O S I T I O
N E X T
S E Q U E N C E
N
P O S I T I O
N
C H A N N E L - S P E C I F I C
P R O G R A M A B L E
P T I O N S
M
O
N O R M A L
S E Q U E N C I N G
S E Q U E N C I N G
I T H E N A B L E
S E Q U E N C I N G
W
I T H C H A N N E L
B Y P A S S
W
E N A B L E
I 2 C P W
=
P W R E N 0 P I N
E N A B L E P W R E N 0 P I N
X O
I 2 C P W R E N A B L E B I T
=
X O
R
R
R
E N A B L E B I T
P O W E R
P O W E R
P O W E R
O N D E L A Y
O N D E L A Y
O N D E L A Y
W
A I T F O R
E N A B L E
E N A B L E
L O W
E N A B L E
H I G H
E N A B L E
L O W
E N A B L E
H I G H
S O F T -
S T A R T
W
A I T F O R
E N A B L E
E N A B L E
H I G H
E N A B L E
L O W
M O N I T O R
S O F T -
S T A R T
V O U T < = U V
V O U T < = U V
Figure 7 – Power-on sequencing flow chart: There are three automated power-on sequencing modes, and a
manual mode.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
23
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
MINIMUM LOAD
The duty cycle is limited to a 10-90% range.
Consequently, the boost channels require a minimum
load to prevent over voltage conditions from occurring.
This may be overcome by attaching a resistor preload
to the output that matches the minimum load
requirements. This approach will result in a constant
current consumption while the outputs are enabled.
Alternatively, a zener diode (with a higher breakdown
voltage than the output) can be connected across the
output clamping the output voltage. This approach will
not draw current when the load is enabled on the
output.
The margin command registers contain two bits for
each channel that decode the commands to margin
high, margin low, or control to the nominal setting.
Therefore, any combination of margin high, margin low,
and nominal control is allowed in the margining mode.
Once the SMB110 receives the command to margin the
supply voltages, it begins adjusting the supply voltages
to move toward the desired setting. When all channels
are at their voltage setting, a bit is set in the margin
status registers.
Note: Configuration writes or reads of registers
should not be performed while margining.
MARGINING
A typical application utilizing the margining functionality
is depicted in Figure 8. When used with a boost
controller setup as a constant current white LED driver,
margining can be used to adjust the current through the
LED chain as an adjustable brightness control.
The SMB110 has two additional voltage settings for
channels 0-3, margin high and margin low. The margin
high and margin low voltage settings have the same
voltage range as the controllers’ nominal output
voltage. These settings are stored in the configuration
registers and are loaded into the voltage setting by
margin commands issued via the I2C bus.
VIN
PCHSEQ
SMB110
BOOST
LSDRV
COMP1(0-1.0V)
COMP2
Figure 8 Boost configured as a constant current white LED driver with adjustable current capabilities.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
24
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
VBATT
C20
10uF
2.7 to 5.5V
L6
R9
10
VBATT
Place close to part
Q2
MOSFET P
D3 DIODE SCHOTTKY
Channel
Setpoint -7.45V
Programmable
0
INDUCTOR FERRITE
L3
C44
C43
33uH
0.1uF
10uF
C2
C1
VREF_OUT
0.1uF
1uF
C18
from -0.8V to -9
22uF
C16
R6
392K
x
VBATT
U2
100pF
VBATT VBATT VBATT
SMB110
5
6
7
4
COMP1_CH0
COMP2_CH0
LSDRV_CH0
VREF_OUT
9
R8
C17
R5
316
C15
VDDCAP
VBATT
11K
3300pF
3300pF
10
R20
47K
R22
47K
R23
47K
R7
11
16
12
13
C38
0.1uF
33K
PCHSEQ_CH1
LSDRV_CH1
COMP1_CH1
COMP2_CH1
28
PWREN0
PWREN0
14
1
RESET#
HEALTHY
nRESET
22
19
17
21
20
18
HEALTHY
VM_CH2
HSDRV_CH2
LSDRV_CH2
COMP1_CH2
COMP2_CH2
HVSUP2
8
HOST_RESET
HOST_RESET
LDO_SUPPLY
VSTANDBY
IMBUS
R17 10
23
24
VBATT
3.3V LDO
Q4
R19
100K
Q2(P)
VBATT
31
27
25
30
29
26
C28
C29 C27
VM_CH3
HSDRV_CH3
LSDRV_CH3
COMP1_CH3
COMP2_CH3
HVSUP3
10uF
0.1uF
0.01uF
R24
47K
R27
47K
C35
C34
L4
33uH
10uF
0.1uF
2
3
SDA
SCL
SDA
SCL
R18 10
D4 DIODE SCHOTTKY
IMBUS
Q1(N)
MOSFET DUAL
Channel
Setpoint 5.5V
1
C25
22uF
R14
90K
C24
100pF
Programmable from
0.8V to .9
VBATT
x
IMBUS
R16
15K
C22
1800pF
R15
432
C23
2700pF
R21
C39
10uF
6.8K
Q1
Q2(P)
R10
10
IMBUS
L1
6.8uH
R11
10
Channel
Setpoint
3.3V
Programmable
from 0.8V to
2
Q1(N)
MOSFET DUAL
C32
C33
C5
10uF
0.1uF
C9
22uF
2700pF
C10
68pF
.9
x VBATT
R1
365
R2
12K
C11
1000pF
Q3
Q2(P)
R12
10
VBATT
L2
6.8uH
Channel
3
Setpoint 5.0V
Programmable
from 0.8V to .9
R13
10
Q1(N)
MOSFET DUAL
C30
C31
C7
10uF
0.1uF
C12
22uF
x
VBATT
2700pF
C13
68pF
R4
365
R3
12K
C14
1000pF
Figure 9 – Applications schematic.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
25
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
Vendor / Part
Item
Description-
Qty
Ref. Des.
Number
Resistors
365Ω, 1/16W, 1%, 0402, SMD
12KΩ 1/16W, 1%, 0402, SMD
316KΩ, 1/16W, 1%, 0402, SMD
392KΩ, 1/16W, 5%, 0402, SMD
33KΩ, 1/16W, 5%, 0402, SMD
11KΩ, 1/16W, 5%, 0402, SMD
10Ω, 1/16W, 5%, 0402, SMD
90KΩ, 1/16W, 5%, 0402, SMD
432Ω, 1/16W, 5%, 0402, SMD
15KΩ, 1/16W, 5%, 0402, SMD
100KΩ, 1/16W, 1%, 0402, SMD
47KΩ, 1/16W, 5%, 0402, SMD
6.8KΩ, 1/16W, 1%, 0402, SMD
Any
1
2
3
4
5
6
7
8
9
10
11
12
13
2
2
1
1
1
1
7
1
1
1
1
1
5
R1, R4
R2, R3
R5
R6
R7
Any
Any
Any
Any
Any
Any
Any
R8
R9, R10, R11, R12, R13, R17, R18
R14
R15
R16
R19
Any FDC6432SH
Any
Any
Any
Any
R20, R22, R23, R24, R27
R21
Capacitors
Any
Any
Any
Any
Any
Any
Any
Any
Any
Any
Any
14
15
16
17
18
19
20
21
22
23
24
7
1
4
3
2
2
2
2
7
1
1
C1, C29, C31, C33, C34, C38, C43
C2
C5, C7, C18, C25
C9, C12, C23
C10, C13
C11, C14
C15, C17
C16, C24
0.1uF, 16V, ceramic, X7R, 0402, SMD
1uF, 16V, ceramic, X7R, 0402, SMD
22uF, 6.3V, ceramic, Y5V, 1210, SMD
2700pF, 50V, ceramic, X7R, 0402, SMD
68pF , 50V, ceramic, X7R, 0402, SMD
1000pF, 50V, ceramic, X7R, 0402, SMD
3300pF, 50V, ceramic, COG, 0402, SMD
100pF, 50V, ceramic, C0G, 0402, SMD
10uF, 6.3V, ceramic, X5R, 0805, SMD
1800pF, 50V ceramic, X7R, 0402, SMD
0.01uF, 50V, ceramic, X7R, 0402, SMD
C20, C28, C30, C32, C35, C39, C44
C22
C27
Semiconductors
Panasonic,
MA2SD24
Fairchild,
25
26
Diode, Schottky, 20V, 200mA SS-MI
MOSFET p-channel, 20V, 0.05 Ohm.
2
1
D3, D4
Q2
FDC640P
Fairchild,
MOSFET, Complementary, Fairchild
Semiconductor, FDC6420C
27
28
FDC6420C or
equivalent
Summit
3
1
Q1, Q3, Q4
U1
SMB110N
Microelectronics
Summit Microelectronics, Inc
2099 2.3 3/1/2005
26
SMB110
Preliminary Information
APPLICATIONS INFORMATION (CONTINUED)
Item
Description-
Vendor / Part Number
Qty
Ref. Des.
Coilcraft DO1608C-333 or Asatech
33uH
29
L2, L3, L8
Inductor, 33uH, SMD
3
Sumida Corp CR436R8 or Coilcraft
DO1608C-682 or Asatech 6.8uH
30
Inductor, 6.8uH, SMD
3
L4, L5, L7
Summit Microelectronics, Inc
2099 2.3 3/1/2005
27
SMB110
Preliminary Information
DEVELOPMENT HARDWARE & SOFTWARE
The end user can obtain the Summit SMX3200 parallel
port programming system or the I2C2USB (SMX3201)
USB programming system for device prototype
development. The SMX3200(1) systems consists of a
programming Dongle, cable and WindowsTM GUI
software. It can be ordered on the website or from a
local representative. The latest revisions of all software
and an application brief describing the SMX3200 and
then configured on-screen via an intuitive graphical user
interface employing drop-down menus.
The Windows GUI software will generate the data and
send it in I2C serial bus format so that it can be directly
downloaded to the SMB110 via the programming Dongle
and cable. An example of the connection interface is
shown in Figure 11.
When design prototyping is complete, the software can
generate a HEX data file that should be transmitted to
Summit for approval. Summit will then assign a unique
customer ID to the HEX code and program production
devices before the final electrical test operations. This
will ensure proper device operation in the end
application.
SMX3201
are
available
from
the
website
(http://www.summitmicro.com).
The SMX3200 programming Dongle/cable interfaces
directly between a PC’s parallel port and the target
application; while the SMX3201 interfaces directly to the
PC’s USB port and the target application. The device is
Top view of straight 0.1" x 0.1 closed-side
connector. SMX3200(1) interface cable
connector.
Pin 9, 5.0V
Pin 10, Reserved
Pin 8, Reserved
Pin 6, MR#
Pin 7, 10V
Pin 5, Reserved
Pin 3, GND
Pin 1, GND
Pin 4, SDA
Pin 2, SCL
10 9
8
6
4
2
7
5
3
1
SMB110
0.1µF
SDA
SCL
GND
Figure 10 -- SMX3200(1) Programmer I2C serial bus connections to program the SMB110.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
28
SMB110
Preliminary Information
I2C PROGRAMMING INFORMATION
SERIAL INTERFACE
Access to the configuration registers, general-purpose
memory and command and status registers is carried
out over an industry standard 2-wire serial interface
(I2C). SDA is a bi-directional data line and SCL is a clock
input. Data is clocked in on the rising edge of SCL and
clocked out on the falling edge of SCL. All data transfers
begin with the MSB. During data transfers, SDA must
remain stable while SCL is high. Data is transferred in 8-
bit packets with an intervening clock period in which an
Acknowledge is provided by the device receiving data.
The SCL high period (tHIGH) is used for generating Start
and Stop conditions that precede and end most
transactions on the serial bus. A high-to-low transition of
SDA while SCL is high is considered a Start condition
while a low-to-high transition of SDA while SCL is high is
considered a Stop condition.
After the last byte is clocked in and the host receives an
Acknowledge, a Stop condition must be issued to initiate
the nonvolatile write operation.
READ
The address pointer for the non-volatile configuration
registers and memory registers as well as the volatile
command and status registers must be set before data
can be read from the SMB110. This is accomplished by
issuing a dummy write command, which is a write
command that is not followed by a Stop condition. A
dummy write command sets the address from which
data is read. After the dummy write command is issued,
a Start command followed by the address byte is sent
from the host. The host then waits for an Acknowledge
and then begins clocking data out of the slave device.
The first byte read is data from the address pointer set
during the dummy write command. Additional bytes can
be clocked out of consecutive addresses with the host
providing an Acknowledge after each byte. After the
data is read from the desired registers, the read
operation is terminated by the host holding SDA high
during the Acknowledge clock cycle and then issuing a
Stop condition. Refer to Figure 13 for an illustration of
the read sequence.
The interface protocol allows operation of multiple
devices and types of devices on a single bus through
unique device addressing.
The address byte is
comprised of a 7-bit device type identifier (slave
address). The remaining bit indicates either a read or a
write operation. Refer to Table 1 for a description of the
address bytes used by the SMB110.
The device type identifier for the memory array, the
configuration registers and the command and status
registers are accessible with the same slave address.
The slave address can be can be programmed to any
CONFIGURATION REGISTERS
The configuration registers are grouped with the general-
purpose memory.
seven bit number 0000000BIN through 1111111BIN
.
GENERAL-PURPOSE MEMORY
WRITE
The 96-byte general-purpose memory block is
segmented into two continuous independently lockable
blocks. The first 48-byte memory block begins at register
address pointer A0HEX and the second memory block
begins at the register address pointer C0HEX; see Table
1. Each memory block can be locked individually by
writing to a dedicated register in the configuration
memory space.
Writing to the memory or a configuration register is
illustrated in Figures 11 and 12. A Start condition
followed by the slave address byte is provided by the
host; the SMB110 responds with an Acknowledge; the
host then responds by sending the memory address
pointer or configuration register address pointer; the
SMB110 responds with an acknowledge; the host then
clocks in one byte of data.
For memory and
configuration register writes, up to 15 additional bytes of
data can be clocked in by the host to write to
consecutive addresses within the same page.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
29
SMB110
Preliminary Information
I2C PROGRAMMING INFORMATION (CONTINUED)
GRAPHICAL USER INTERFACE (GUI)
the process of device prototyping and the interaction of
the various functional blocks. A programming Dongle
(SMX3200) is available from Summit to communicate
with the SMB110. The Dongle connects directly to the
parallel port of a PC and programs the device through a
cable using the I2C bus protocol. See figure 7 and the
SMX3200 Data Sheet.
Device configuration utilizing the Windows based
SMB110 graphical user interface (GUI) is highly
recommended. The software is available from the
Summit website (http://www.summitmicro.com ). Using
the GUI in conjunction with this datasheet, simplifies
Slave
Register Type
Address
Configuration Registers are located in
00 HEX thru 9FHEX
0000000BIN
to
General-Purpose Memory Block 0 is
located in A0 HEX thru BFHEX
General-Purpose Memory Block 1 is
located in C0 HEX thru FFHEX
1111111BIN
Table 1 – Possible address bytes used by the SMB110.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
30
SMB110
Preliminary Information
I2C PROGRAMMING INFORMATION (CONTINUED)
S
T
S
T
O
P
A
Configuration
Register Address
R
T
Master
Slave
Bus Address
Data
S
A
3
S
A
2
S
A
1
S
A
0
A
2
A
1
A
0
C
7
C
6
C
5
C
4
C
3
C
2
C
1
C
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
W
A
C
K
A
C
K
A
C
K
Figure 11 –Register Byte Write
S
T
A
R
T
Configuration
Register Address
Master
Bus Address
Data (1)
S
A
3
S
A
2
S
A
1
S
A
0
A
2
A
1
A
0
C
7
C
6
C
5
C
4
C
3
C
2
C
1
C
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
W
Slave
A
C
K
A
C
K
A
C
K
S
T
O
P
Master
Slave
Data (2)
Data (16)
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
D
7
D
6
D
5
D
2
D
1
D
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
A
C
K
A
C
K
A
C
K
Figure 12 –Register Page Write
S
T
A
R
T
S
T
A
R
T
Configuration
Register Address
Master
Slave
Bus Address
Bus Address
S
A
3
S
A
2
S
A
1
S
A
0
S
A
3
S
A
2
S
A
1
S
A
0
A
2
A
1
A
0
C
7
C
6
C
5
C
4
C
3
C
2
C
1
C
0
A
2
A
1
A
0
W
R
A
C
K
A
C
K
A
C
K
N
A
C
K
S
T
O
P
A
C
K
A
C
K
Master
Slave
Data (1)
Data (n)
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
D
7
D
6
D
5
D
2
D
1
D
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Figure 13 -Register Read
Summit Microelectronics, Inc
2099 2.3 3/1/2005
31
SMB110
Preliminary Information
DEFAULT CONFIGURATION REGISTER SETTINGS – SMB110NC-323L
Register
Contents
Register
Contents
Register
Contents
00
20
00
02
02
02
02
30
30
30
30
03
00
02
00
39
2E
CF
5B
71
95
DF
65
8A
B6
R0
D7
R15
R2C
R3
R4
R5
R8
RB
RC
RD
R10
R11
R12
R13
R14
60
7D
A5
30
60
50
40
96
5A
14
50
A0
R16
R17
R18
R1B
R1C
R1D
R20
R23
R24
R27
R2A
R2B
R2D
R2E
R2F
R50
R53
R54
R57
R58
R5B
R5C
R5D
The default device ordering number is SMB110NC-323L. It is programmed with the register contents as shown above
and tested over the commercial temperature range. The ordering number is derived from the customer supplied hex file.
New device suffix numbers are assigned to non-default requirements.
Summit Microelectronics, Inc
2099 2.3 3/1/2005
32
SMB110
Preliminary Information
PACKAGE
Summit Microelectronics, Inc
2099 2.3 3/1/2005
33
SMB110
Preliminary Information
PART MARKING
Summit
SUMMIT
Part Number
Status Tracking Code
(Blank, MS, ES, 01, 02,...)
(Summit Use)
SMB110N
xx
Annn
L
AYYWW
Pin 1
Date Code (YYWW)
Lot tracking code (Summit use)
100% Sn, RoHS compliant, Green
Drawing not
to scale
Part Number suffix
(Contains Customer specific
ordering requirements)
Product Tracking Code (Summit use)
ORDERING INFORMATION
SMB110 N C nnn L
Summit
Part
Solder Composition
L = 100% Sn, RoHS compliant, Green
Blank = 85% Sn, 15% Pb
Number
Package
Part Number Suffix
N = 32 Pad QFN
Specific requirements are contained in the suffix
Temperature Range
C = Commercial
NOTICE
NOTE 1 - This is a Preliminary Information data sheet that describes a Summit product currently in pre-production with limited
characterization.
SUMMIT Microelectronics, Inc. reserves the right to make changes to the products contained in this publication in order to improve
design, performance or reliability. SUMMIT Microelectronics, Inc. assumes no responsibility for the use of any circuits described
herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent
infringement. Charts and schedules contained herein reflect representative operating parameters, and may vary depending upon a
user’s specific application. While the information in this publication has been carefully checked, SUMMIT Microelectronics, Inc. shall
not be liable for any damages arising as a result of any error or omission.
SUMMIT Microelectronics, Inc. does not recommend the use of any of its products in life support or aviation applications where the
failure or malfunction of the product can reasonably be expected to cause any failure of either system or to significantly affect their
safety or effectiveness. Products are not authorized for use in such applications unless SUMMIT Microelectronics, Inc. receives
written assurances, to its satisfaction, that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks;
and (c) potential liability of SUMMIT Microelectronics, Inc. is adequately protected under the circumstances.
Revision 2.2 - This document supersedes all previous versions. Please check the Summit Microelectronics Inc. web site at
http://www.summitmicro.com for data sheet updates.
© Copyright 2005 SUMMIT MICROELECTRONICS, Inc. PROGRAMMABLE ANALOG FOR A DIGITAL WORLD™
ADOCTM is a registered trademarks of Summit Microelectronics Inc., I C is a trademark of Philips Corporation.
2
Summit Microelectronics, Inc
2099 2.3 3/1/2005
34
相关型号：
SMB1115005
RF SMB Connector, 1 Contact(s), Female, Board Mount, Surface Mount Terminal, Locking, Jack,
SEMIPOWER
SMB1115007
RF SMB Connector, 1 Contact(s), Female, Board Mount, Solder Terminal, Locking, Jack
SEMIPOWER
©2020 ICPDF网 联系我们和版权申明