PIA0603S150MN [SUPERWORLD]
Molded Choke Coil;
| 型号： | PIA0603S150MN |
| 厂家： | 
SUPERWORLD ELECTRONICS |
| 描述： | Molded Choke Coil |
| 文件： | 总8页 (文件大小：336K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
P1
Molded Choke Coil – PIA0603S Series
1. Part No. Expression:
P I A 0 6 0 3 S 1 R 0 M N
a) Series Code
e) Tolerance Code
(a)
(b) (c) (d) (e)(f)
b) Dimension Code
c) Type Code
f) Internal Controlled Code
d) Inductance Code
2. Configuration & Dimensions:
C
A
A`
D
L
Marking
D/C
G
T
Note:
Recommended PC Board Pattern
1. The above PCB layout is for reference only.
2. Solder paste thickness of 0.15mm and above is recommended.
3. Marking: Top row – Inductance code, Bottom row – YYWW
Unit: mm
L
A
A`
B
C
D
E
T
G
H
3.7
3.4
8.0
7.1±0.3 6.4±0.3 6.6±0.2 2.8±0.2 1.6±0.3 3.0±0.2
0~0.15
3. Schematic:
4. Material List:
a) Core
b) Wire
c) Terminal
d) Ink
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P2
Molded Choke Coil – PIA0603S Series
5. General Specification:
(a) Operating Temp. : -40°C to +125°C (Inclusive of coil temp rise)
(b) Storage Temp. : -40°C to +125°C (on board)
(c) Humidity Range : 85 ± 2% RH
(d) Heat Rated Current (Irms) will cause the coil temperature rise approximately ∆t of 40°C (keep 1min)
(e) Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%.
(f) Part Temp. (Ambient + Temp. Rise) should not exceed 125°C under worst case operating conditions.
(g) Storage condition (component in its packaging)
i)
Temperature: -10 to 40°C
Humidity : 50~60% RH
ii)
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P3
Molded Choke Coil – PIA0603S Series
6. Electrical Characteristics:
Heat Rating
Current DC
( A ) Irms.
Saturation
Current DC
(A) Isat.
Test
Frequency, L
Inductance
Lo (uH)
@ 0A
DCR
(mΩ)Typ.
DCR
(mΩ)Max.
Part Number
Typ. Max. Typ. Max.
PIA0603SR15YN
PIA0603SR22MN
PIA0603SR33MN
PIA0603SR36MN
PIA0603SR47MN
PIA0603SR56MN
PIA0603SR68MN
PIA0603SR82MN
PIA0603S1R0MN
PIA0603S1R2MN
PIA0603S1R5MN
PIA0603S1R8MN
PIA0603S2R2MN
PIA0603S2R7MN
PIA0603S3R3MN
PIA0603S4R7MN
PIA0603S5R6MN
PIA0603S6R8MN
PIA0603S8R2MN
PIA0603S100MN
PIA0603S150MN
PIA0603S220MN
PIA0603S330MN
0.15
0.22
0.33
0.36
0.47
0.56
0.68
0.82
1.00
1.20
1.50
1.80
2.20
2.70
3.30
4.70
5.60
6.80
8.20
10.0
15.0
22.0
33.0
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
30
23
21
20
18
25
21
40
34
36
32
1.7
2.0
2.8
3.3
3.4
3.9
4.7
5.4
6.7
7.7
10.2
10.9
13.5
17.3
19
2.1
2.5
3.4
3.9
4.0
4.5
5.3
6.0
7.4
9.5
12.1
13
20
25
22
18
24
21
16
20
18
100kHz/1.0V 16.5
15
18
16
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
100kHz/1.0V
16
14
14.5
13
17
15
16
14
12
11
15
13.5
12.5
12
10
9.5
9.0
8.0
7.5
7.0
6.0
5.0
5.0
4.2
4.0
3.5
2.5
2.0
1.8
14
10
14
9.0
8.0
7.2
6.5
5.5
5.5
4.5
4.5
4.0
3.0
2.5
2.1
12
10
10
9.0
8.8
8.5
5.5
5.2
5.0
4.7
4.5
4.0
2.5
2.0
15
9.8
9.5
6.5
6.0
6.0
6.0
5.5
4.5
3.0
2.5
20
22
28
33
39
42
43
50
54
60
62
68
110
150
215
140
190
258
*Tolerance code : M = ±20%, Y= ±30%
Notes:
1) At all times, the current supplied to the product should not exceed Isat Max. value.
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P4
Molded Choke Coil – PIA0603S Series
7. Characteristics Curves:
PIA0603SR15YN
PIA0603SR36MN
PIA0603SR68MN
PIA0603S1R2MN
PIA0603SR22MN
PIA0603SR33MN
PIA0603SR56MN
PIA0603SR47MN
PIA0603SR82MN
PIA0603S1R5MN
PIA0603S1R0MN
PIA0603S1R8MN
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P5
Molded Choke Coil – PIA0603S Series
PIA0603S2R2MN
PIA0603S4R7MN
PIA0603S8R2MN
PIA0603S2R7MN
PIA0603S5R6MN
PIA0603S100MN
PIA0603S3R3MN
PIA0603S6R8MN
PIA0603S150MN
PIA0603S330MN
PIA0603S220MN
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P6
Molded Choke Coil – PIA0603S Series
8. Soldering:
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the
stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our
terminations are suitable for all re-flow soldering systems. If hand soldering cannot be avoided, the preferred
technique is the utilization of hot air.
8-1.1 Solder Re-flow:
Recommended temperature profiles for re-flow soldering in Figure 1.
8-1.2 Soldering Iron (Figure 2):
Products attachment with soldering iron is discouraged due to the inherent process control limitations.
In the event that a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150°C.
b) 355°C tip temperature (Max.)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (Max.)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 4~5 secs.
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P7
Molded Choke Coil – PIA0603S Series
9. Packaging Information:
9-1 Reel Dimension
Type
A(mm)
B(mm)
100±2
C(mm)
D(mm)
330
13”x16mm
16.4+2/-0
13+0.5/-0.2
9-2 Tape Dimension
Blank portions
Chip cavity
Blank portions
T
4.0
K0
P
200mm or more
400mm or more
Direction of tape
A0
Series
PIA
Size
Bo(mm) Ao(mm) Ko(mm)
P(mm) W(mm) F(mm)
T(mm)
D(mm)
0603
7.7±0.1 7.0±0.1 3.3±0.1 12.0±0.1 16±0.3 7.5±0.1 0.35±0.05 1.5±0.1
9-3 Packaging Quantity
PIA
0603
Chip / Reel
Inner box
Carton
1000
2000
8000
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
P8
Molded Choke Coil – PIA0603S Series
9-4 Tearing Off Force
The force for tearing off cover tape is 10 to 130 grams in the
arrow direction under the following conditions.
Room
Humidity
(%)
Tearing
Speed
mm/min
Room Temp.
Room atm
(hPa)
(℃)
5~35
45~85
860~1060
300
Application Notice:
1. Storage Conditions:
To maintain the solderabililty of terminal electrodes:
a) Recommended products should be used within 12 months from the time of delivery.
b) The packaging material should be kept where no chlorine or sulfur exists in the air.
2. Transportation:
a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.
b) Vacuum pick up is strongly recommended for individual components.
c) Bulk handling should ensure that abrasion and mechanical shock are minimized.
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
29/09/2017
相关型号：
©2020 ICPDF网 联系我们和版权申明