PIC1004HR22MN [SUPERWORLD]
MOLDED POWER CHOKE COIL; 模压POWER CHOKE COIL
| 型号： | PIC1004HR22MN |
| 厂家： | 
SUPERWORLD ELECTRONICS |
| 描述： | MOLDED POWER CHOKE COIL |
| 文件： | 总8页 (文件大小：332K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MOLDED POWER CHOKE COIL
PIC1004H SERIES
1. PART NO. EXPRESSION :
(a) Series code
(b) Dimension code
(c) Type code
(d) Inductance code : 1R0 = 1.0uH
P I C 1 0 0 4 H 1 R 0 M N -
(e) Tolerance code : M = ± 20%, Y = ± 30%
(a)
(b) (c)
(d) (e)(f)
(g)
(f) No coating
(g) Internal control number : 11 ~ 99
2. CONFIGURATION & DIMENSIONS :
A
C
D
1R0
1104
Unit:m/m
A
B
C
D
E
11.0± 0.5 10.0± 0.3
3.8± 0.2
2.3± 0.3
3.0± 0.3
3. SCHEMATIC :
4. MATERIALS :
(a) Core : Magnetic metal powder or equivalent
(b) Wire : Polyester wire or equivalent
(c) Solder Plating : 100% Pb free solder
(d) Ink : Halogen-free ketone
d
c
a
b
5. GENERAL SPECIFICATION :
a) Test Freq. : L : 100KHz/1V
b) Ambient Temp. : 25° C
c) Operating Temp. : -40° C to +125° C
d) Storage Temp. : -10° C to +40° C
HF
Halogen
Free
e) Humidity Range : 50 ~ 60% RH (Product without taping)
f) Heat Rated Current (Irms) : Will cause the coil temp. rise approximately ǻt of 40°C (keep 1min.)
g) Saturation Current (Isat) : Will cause L0 to drop 20% typical (keep quickly)
h) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125° C under worst case operating conditions.
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
MOLDED POWER CHOKE COIL
PIC1004H SERIES
6. ELECTRICAL CHARACTERISTICS :
Inductance L0
( µH )
Irms
( A )
Typ.
Isat
( A )
Typ.
DCR
DCR
Part No.
( mȍ )
( mȍ )
@ 0 A
Typ. @ 25° C Max. @ 25° C
PIC1004HR22MN
PIC1004HR36MN
0.22 ± 20%
0.36 ± 20%
35
31
60
60
0.8
1.0
1.2
1.05
PIC1004HR39MN
PIC1004HR45MN
0.39 ± 20%
0.45 ± 20%
0.56 ± 20%
30
29
25
18
60
45
40
36
1.1
1.3
1.6
3.0
1.3
1.5
1.8
3.3
PIC1004HR56MN
PIC1004H1R0MN
PIC1004H2R2MN
PIC1004H3R3MN
PIC1004H4R7MN
1.00 ± 20%
2.20 ± 20%
3.30 ± 20%
4.70 ± 20%
6.80± 20%
10.0 ± 20%
12
11
27
20
6.5
7.0
11.8
15.5
23.3
30
10.8
15.0
17.5
27.0
10
17
PIC1004H6R8MN
PIC1004H100MN
8.5
7.5
13.5
12.0
7. CHARACTERISTICS CURVES :
PIC1004HR36MN
PIC1004HR22MN
0.4
0.3
0.2
0.1
0
100
90
80
70
60
50
40
30
20
10
0
0.8
0.6
0.4
0.2
0
100
90
80
70
60
50
40
30
20
10
0
0
15
30
45
60
0
15
30
45
60
DC CURRENT(A)
DC CURRENT(A)
HF
Halogen
Free
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 2
MOLDED POWER CHOKE COIL
PIC1004H SERIES
7. CHARACTERISTICS CURVES :
PIC1004HR39MN
PIC1004HR45MN
0.8
0.6
0.4
0.2
0
100
90
80
70
60
50
40
30
20
0.8
0.6
0.4
0.2
0
100
90
80
70
60
50
40
30
20
10
0
10
0
0
1
15
30
45
60
0
9
18
27
36
45
DC CURRENT(A)
DC CURRENT(A)
PIC1004HR56MN
PIC1004H1R0MN
80
70
60
50
40
30
20
10
0
2
1.5
1
100
90
80
70
60
50
40
30
20
0.8
0.6
0.4
0.2
0.5
0
10
0
36
0
0
8
16
24
32
40
0
9
18
27
DC CURRENT(A)
DC CURRENT(A)
PIC1004H3R3MN
PIC1004H2R2MN
6
4.5
3
80
70
60
50
40
30
20
10
0
4
80
70
60
50
40
30
20
10
0
3
2
1
0
1.5
0
0
5
10
15
20
0
6.75
13.5
20.25
27
DC CURRENT(A)
DC CURRENT(A)
HF
Halogen
Free
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3
MOLDED POWER CHOKE COIL
PIC1004H SERIES
7. CHARACTERISTICS CURVES :
PIC1004H4R7MN
PIC1004H6R8MN
8
6
4
2
0
80
70
60
50
40
30
20
10
0
12
9
80
70
60
50
40
30
20
10
0
6
3
0
0
4.25
8.5
12.75
17
0
3.375
6.75
10.125
13.5
DC CURRENT(A)
DC CURRENT(A)
PIC1004H100MN
20
15
10
5
80
70
60
50
40
30
20
10
0
0
0
3
6
9
12
DC CURRENT(A)
HF
Halogen
Free
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4
MOLDED POWER CHOKE COIL
PIC1004H SERIES
8. RELIABILITY AND TEST CONDITION
ITEM
PERFORMANCE
TEST CONDITION
Electrical Characteristics Test
HP4284A, CH11025, CH3302, CH1320, CH1320S
LCR meter.
Inductance
Refer to standard electrical characteristics list
DCR
CH16502, Agilent33420A Micro-Ohm Meter.
Heat Rated Current (Irms)
Irms(A) will cause the coil temperature rise
approximately ǻT of 40°C without core loss
1. Applied the allowed DC current(keep 1min).
2. Temperature measured by digital surface thermometer
Saturation Current (Isat)
Reliability Test
ǻL20% typical
Isat(A) will cause Lo to drop
Electric specification should be satisfied
Temperature : 125± 2° C
Time : 1000± 12hrs
Measured at room temperature after placing for 2 to 3hrs
High
Temperature Test
(MIL-PRF-27)
Low
Temperature : -40± 2° C
Time :500± 12hrs
Measured at room temperature after placing for 2 to 3hrs
Temperature Test
Thermal Shock
Conditions of 1 cycle.
Step
Temperature (° C) Times (min.)
1
2
3
-40+0/-2
Room Temperature
+125+2/-0
15± 1
Within <0.2
15± 1
Total : 300 cycles
Measure at room temperature after placing for 2 to 3 hrs.
(AEC-Q200-REV C)
Humidity Resistance
Temperature : 85± 2° C
Humidity : 85± 3% RH
Time : 1000± 12hrs
Measured at room temperature after placing for 2 to 3hrs
(AEC-Q200-REV C)
Random Vibration
Test
Frequency : 10-2000-10Hz for 20 min.
Amplitude: Parts mounted within 2" from any secure point
Directions and times : X, Y, Z directions for 20 min.
This cycle shall be performed 12 times in each of three
mutually perpendicular directions.
(Total 12hours).
(MIL-STD-202 Method 204 D Test condition B)
Reflow Test
Solder test
Preheat : 150± 5° C
Duration : 5 minutes
Temperature : 260± 5° C, 20-40 seconds
(IPC/JEDEC J-STD-020C)
Terminals should be covered by over 95%
solder on visual inspection.
After dip into fluxˈdip into solder
235± 5° C, 4± 1seconds
Flux, solder for lead free
(ANSI/J-STD-002C Method B)
HF
Halogen
Free
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5
MOLDED POWER CHOKE COIL
PIC1004H SERIES
9. SOLDERING AND MOUNTING :
9-1. Recommended PC Board Pattern
13.6
5.4
9-2. Soldering
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused
by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all
wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot
air soldering tools.
9-2.1 Solder Re-flow :
Recommended temperature profiles for re-flow soldering in Figure 1.
9-2.2 Soldering Iron (Figure 2) :
Products attachment with soldering iron is discouraged due to the inherent process control limitations.
In the event that a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150° C.
b) 355° C tip temperature (max)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (max)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 4-5 secs.
Preheating
Soldering
20~40s
Natural
cooling
Preheating
Soldering
Natural
cooling
350
150
TP(260° C/40s max.)
217
200
150
60~150s
60~180s
480s max.
25
Gradual
Cooling
Time(sec.)
Over 1min.
Within 4-5s
Figure 1. Re-flow Soldering
Figure 2. Iron Soldering
HF
Halogen
Free
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 6
MOLDED POWER CHOKE COIL
PIC1004H SERIES
10. PACKAGING INFORMATION :
10-1. Reel Dimension
COVER TAPE
2.0± 0.5
A
EMBOSSED CARRIER
Type
A(mm)
B(mm)
C(mm)
D(mm)
330
13" x 24mm 24.0± 0.5 100± 2.0 13.5± 0.5
10-2 Tape Dimension
4.0
2.0
Ø1.5
t
P
Ko
Ao
Series
Ao(mm)
Bo(mm)
Ko(mm)
P(mm)
W(mm)
F(mm)
t(mm)
PIC1004H
10.4± 0.1 11.6± 0.1 4.5± 0.1 16.0 ± 0.1 24.0± 0.3 11.5± 0.1 0.35± 0.05
10-3. Packaging Quantity
Size
1004
500
HF
Chip / Reel
Inner Box
Carton
Halogen
Free
1000
4000
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 7
MOLDED POWER CHOKE COIL
PIC1004H SERIES
10-4. Tearing Off Force
The force for tearing off cover tape is 10 to 130 grams
in the arrow direction under the following conditions.
(referenced ANSI/EIA-481-C-2003 of 4.11 standard)
F
180°
165° to
Room Temp.
(° C)
Room Humidity
(%)
Room atm Tearing Speed
Top cover tape
(hPa)
(mm/min)
5~35
45~85
860~1060
300
Base tape
Application Notice
1. Storage Conditions :
To maintain the solderabililty of terminal electrodes :
a) Temperature and humidity conditions : Less than 30° C and 70% RH.
b) Recommended products should be used within 6 months from the time of delivery.
c) The packaging material should be kept where no chlorine or sulfur exists in the air.
2. Transportation :
a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.
b) The use of tweezers or vacuum pick up is strongly recommended for individual components.
c) Bulk handling should ensure that abrasion and mechanical shock are minimized.
HF
Halogen
Free
NOTE : Specifications subject to change without notice. Please check our website for latest information.
25.02.2011
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 8
相关型号：
©2020 ICPDF网 联系我们和版权申明