PIC1235HP1R5MF [SUPERWORLD]
SMD Power Choke Coil;型号: | PIC1235HP1R5MF |
厂家: | SUPERWORLD ELECTRONICS |
描述: | SMD Power Choke Coil |
文件: | 总9页 (文件大小:613K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SMD Power Choke Coil
PIC1235HP SERIES
1. PART NO. EXPRESSION :
(a) Series code
(b) Dimension code
(c) Type code
(d) Inductance code : 1R0 = 1.0uH
P I C 1 2 3 5 H P 1 R 0 M F - □□
(e) Tolerance code : M = ±20%, Y = ±30%
(f) F : RoHS Compliant
(a)
(b)
(c)
(d) (e)(f)
(g)
(g) 11~99 : Internal controlled number
2. CONFIGURATION & DIMENSIONS :
A
C
D
L
G
1R0
1206
Recommended PC Board Pattern
Unit:m/m
L
A
B
C
D
E
G
H
13.5±0.5 12.5±0.3
3.3±0.2
2.3±0.3
4.7±0.3
8.0
5.0
14.2
3. SCHEMATIC :
4. MATERIALS :
(a) Core
(b) Wire
(c) Terminal
(d) Ink
(e) Paint
5. GENERAL SPECIFICATION :
a) Test Freq. : L : 100KHz/1.0V
b) Operating Temp. : -40°C to +125°C
c) Storage Temp. : -40°C to +125°C
d) Humidity Range : 85 ± 3% RH
e) Heat Rated Current (Irms) will cause the coil temperature rise approximately Δt of 40°C (keep 1min)
f ) Saturation Current (Isat) will cause L0 to drop 20%.
g) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125°C under worst case operating conditions.
h) Storage condition (component in its packaging)
i) Temperature: -10 to 40°C
ii) Humidity : 50~60% RH
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
SMD Power Choke Coil
PIC1235HP SERIES
6. ELECTRICAL CHARACTERISTICS :
Inductance L0
Irms
( A )
Typ.
Isat
( A )
Typ.
DCR
( mΩ )
Typ. @ 25°C
DCR
( mΩ )
Max. @ 25°C
Part No.
( μH )
@ 0 A
PIC1235HPR10YF
PIC1235HPR15YF
PIC1235HPR22MF
PIC1235HPR33MF
PIC1235HPR36MF
PIC1235HPR45MF
PIC1235HPR47MF
PIC1235HPR56MF
PIC1235HPR60MF
PIC1235HPR67MF
PIC1235HPR68MF
PIC1235HPR82MF
PIC1235HP1R0MF
PIC1235HP1R2MF
PIC1235HP1R5MF
PIC1235HP1R8MF
PIC1235HP2R2MF
PIC1235HP3R3MF
PIC1235HP4R7MF
PIC1235HP5R6MF
PIC1235HP6R8MF
PIC1235HP8R2MF
PIC1235HP100MF
Tolerance : M = ±20%, Y = ±30%
0.10
0.15
0.22
0.33
0.36
0.45
0.47
0.56
0.60
0.67
0.68
0.82
1.00
1.20
1.50
1.80
2.20
3.30
4.70
5.60
6.80
8.20
10.0
43
41
84
75
65
62
60
58
55
53
51
49
49
44
40
37
35
30
29
27
24
19
18
16
14
0.36
0.4
0.7
0.85
0.87
1.05
1.2
1.3
1.5
1.9
1.9
2.2
2.7
4.0
4.8
5.2
6.3
11
0.43
0.48
0.81
1.0
1.1
1.5
1.8
1.9
2.2
2.5
2.5
3.0
3.5
5.0
5.5
7.0
8.0
13.5
18.5
22
38.5
36.5
36
33
32
30
29
28
28
25
24
21
19
17
16
12
10
15.3
18
9.5
9.0
8.5
7.0
20
24
23
28
29
34
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 2
SMD Power Choke Coil
PIC1235HP SERIES
7. CHARACTERISTICS CURVES :
PIC1235HPR10YF
PIC1235HPR15YF
PIC1235HPR22MF
PIC1235HPR33MF
PIC1235HPR45MF
PIC1235HPR36MF
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3
SMD Power Choke Coil
PIC1235HP SERIES
PIC1235HPR47MF
PIC1235HPR56MF
PIC1235HPR68MF
PIC1235HPR60MF
PIC1235HPR82MF
PIC1235HP1R0MF
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4
SMD Power Choke Coil
PIC1235HP SERIES
PIC1235HP1R2MF
PIC1235HP1R5MF
PIC1235HP1R8MF
PIC1235HP2R2MF
PIC1235HP4R7MF
PIC1235HP3R3MF
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5
SMD Power Choke Coil
PIC1235HP SERIES
PIC1235HP5R6MF
PIC1235HP6R8MF
PIC1235HP100MF
PIC1235HP8R2MF
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 6
SMD Power Choke Coil
PIC1235HP SERIES
8. SOLDERING
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused
by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all
re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air
soldering tools.
8-1.1 Solder Re-flow :
Recommended temperature profiles for re-flow soldering in Figure 1.
8-1.2 Soldering Iron (Figure 2) :
Products attachment with soldering iron is discouraged due to the inherent process control limitations.
In the event that a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150°C.
b) 355°C tip temperature (max)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (max)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 4~5 secs.
Preheating
Soldering
20~40s
Natural
cooling
Preheating
Soldering
Natural
cooling
350
150
TP(260°C/40s max.)
217
200
150
60~150s
60~180s
480s max.
25
Gradual
Cooling
Time(sec.)
Over 1min.
Within 4-5s
Figure 2. Hand Soldering: 1 times max.
Figure 1. Re-flow Soldering: 3 times max.
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 7
SMD Power Choke Coil
PIC1235HP SERIES
9. PACKAGING INFORMATION :
9-1. Reel Dimension
COVER TAPE
2.0±0.5
A
EMBOSSED CARRIER
Type
A(mm)
B(mm)
C(mm)
D(mm)
330
13" x 24mm 24.4+2.0/-0 100±2.0
13.5±0.5
9-2. Tape Dimension
4.0
2.0
1.5
t
P
Az
Ao
Series
Ao(mm)
Az(mm)
Bo(mm)
Bz(mm)
Ko(mm)
4.0±0.1
P(mm)
W(mm)
24±0.3
F(mm)
t(mm)
PIC1235
12.9±0.1
7.0±0.1
14.1±0.1 13.0±0.1
16.0±0.1
11.5±0.1 0.35±0.05
9-3. Packaging Quantity
Size
PIC1235
500
Chip / Reel
Inner Box
Carton
1000
4000
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 8
SMD Power Choke Coil
PIC1235HP SERIES
9-4. Tearing Off Force
The force for tearing off cover tape is 10 to 130 grams
in the arrow direction under the following conditions.
(referenced ANSI/EIA-481-C-2003 of 4.11 standard)
F
165° to 180°
Room Temp.
Room Humidity
(%)
Room atm Tearing Speed
Top cover tape
(°C)
(hPa)
(mm/min)
5~35
45~85
860~1060
300
Base tape
Application Notice
1. Storage Conditions :
To maintain the solderabililty of terminal electrodes :
a) Recommended products should be used within 12 months from the time of delivery.
b) The packaging material should be kept where no chlorine or sulfur exists in the air.
2. Transportation :
a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.
b) Vacuum pick up is strongly recommended for individual components.
c) Bulk handling should ensure that abrasion and mechanical shock are minimized.
NOTE : Specifications subject to change without notice. Please check our website for latest information.
06.11.2015
SUPERWORLD ELECTRONICS (S) PTE LTD
PG.9
相关型号:
©2020 ICPDF网 联系我们和版权申明