PIF0603A1R2MN [SUPERWORLD]
High Current Power Inductor;
| 型号： | PIF0603A1R2MN |
| 厂家： | 
SUPERWORLD ELECTRONICS |
| 描述： | High Current Power Inductor |
| 文件： | 总7页 (文件大小：476K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
P1
High Current Power Inductor– PIF0603A Series
1. Part No. Expression:
P I F 0 6 0 3 A 1 R 0 M N
(a) (b) (c) (d) (e)(f)
a) Series Code
e) Tolerance Code
f) Internal Controlled Code
b) Dimension Code
c) Type Code
d) Inductance Code
2. Configuration & Dimensions:
L
G
Note:
Recommended PC Board Pattern
1. The above PCB layout is for reference only.
2. Solder paste thickness of 0.15mm and above is recommended.
Unit: mm
Part Number
A
B
C
D
E
F
L
G
H
5.6 Ref. 2.5 Ref. 5.6 Ref.
PIF0603AR18MN
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
6.6±0.2 6.4±0.2
2.8±0.2
5.30
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
1.4±0.2 2.6±0.25
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
5.6 Ref.
PIF0603AR33MN
PIF0603AR56MN
PIF0603A1R0MN
PIF0603A1R2MN
PIF0603A1R8MN
PIF0603A2R2MN
PIF0603A3R3MN
PIF0603A4R5MN
2.8±0.2
2.8±0.2
2.8±0.2
2.8±0.2
2.9±0.2
2.9±0.2
2.9±0.2
2.9±0.2
5.55
5.30
5.20
5.15
5.10
5.05
5.00
5.00
2.5 Ref.
2.5 Ref.
2.5 Ref.
2.5 Ref.
2.5 Ref.
2.5 Ref.
2.5 Ref.
2.5 Ref.
Proprietary and Confidential
Document of Superworld
18/04/2016
P2
High Current Power Inductor– PIF0603A Series
3. Schematic:
4. Material List:
(a) Core
(b) Wire
(c) Solder
(d) Ink
5. General Specification:
(a) Test Freq. : L : 100KHz/0.1V
(b) Operating Temp. : -40°C to +125°C (including self-temperature rise)
(c) Storage Temp. : -40°C to +125°C (on board)
(d) Humidity Range : 85 ± 2% RH
(e) Heat Rated Current (Irms) will cause the coil temperature rise approximately Δt of 40°C (keep 1min)
Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%.
Part Temperature (Ambient+Temp. Rise) : Should not exceed 125°C under worst case operating conditions.
Storage condition (component in its packaging)
(f)
(g)
(h)
i) Temperature: Less than 40°C
ii)Humidity : 60% RH
Proprietary and Confidential
Document of Superworld
18/04/2016
P3
High Current Power Inductor– PIF0603A Series
6. Electrical Characteristics:
I rms(A) Typ.
@20℃ @40℃
24.0 32.0
I sat(A)
Inductance(uH)
±20% @ 0 A
DCR
DCR
SRF
Part Number
(mΩ) Typ. (mΩ) Max. (MHz) Ref.
Max.
Typ.
40.0
PIF0603AR18MN
PIF0603AR33MN
PIF0603AR56MN
PIF0603A1R0MN
PIF0603A1R2MN
PIF0603A1R8MN
PIF0603A2R2MN
PIF0603A3R3MN
PIF0603A4R5MN
0.18
0.33
0.56
1.00
1.20
1.80
2.20
3.30
4.50
36.0
28.0
25.0
18.0
16.0
13.0
11.0
9.00
8.00
1.60
2.25
3.00
5.50
6.70
9.20
11.0
18.8
23.0
1.75
2.50
3.31
6.05
7.40
10.2
12.2
20.8
25.3
143
78
70
52
47
33
29
25
20
20.0
17.0
13.0
12.0
10.0
7.00
6.00
5.00
25.0
22.0
18.0
16.0
14.0
10.0
8.00
7.00
32.0
29.0
23.0
22.0
18.2
15.9
12.2
10.0
*Tolerance code : M = ±20%, Y= ±30%
Notes:
1) Isat Typ. and Irms Typ. value is derived based from accounting the upper limit tolerance into the inductance value.
2) At all times, the current supplied to the product should not exceed Isat Max. value.
Proprietary and Confidential
Document of Superworld
18/04/2016
P4
High Current Power Inductor– PIF0603A Series
7. Characteristics Curves:
PIF0603AR56MN
PIF0603AR18MN
PIF0603AR33MN
0.3
0.24
0.18
0.12
0.06
0
60
48
36
24
12
0
0.5
0.4
0.3
0.2
0.1
0
50
40
30
20
10
0
1
0.8
0.6
0.4
0.2
0
80
64
48
32
16
0
0
0
0
9
18
27
36
45
0
7
14
21
28
35
0
7
14
21
28
35
DC CURRENT(A)
DC CURRENT(A)
DC CURRENT(A)
PIF0603A1R0MN
PIF0603A1R8MN
PIF0603A1R2MN
1.8
1.44
1.08
0.72
0.36
0
80
3
80
1.5
1.2
0.9
0.6
0.3
0
70
56
42
28
14
0
64
48
32
16
0
2.4
1.8
1.2
0.6
0
64
48
32
16
0
5.2
10.4
15.6
20.8
26
0
5
10
15
20
25
0
4
8
12
16
20
DC CURRENT(A)
DC CURRENT(A)
DC CURRENT(A)
PIF0603A2R2MN
PIF0603A3R3MN
PIF0603A4R5MN
3.5
2.8
2.1
1.4
0.7
0
80
64
48
32
16
0
5
4
3
2
1
0
80
7
80
64
48
32
16
0
64
48
32
16
0
5.6
4.2
2.8
1.4
0
3.4
6.8
10.2
13.6
17
0
2.8
5.6
8.4
11.2
14
0
2.4
4.8
7.2
9.6
12
DC CURRENT(A)
DC CURRENT(A)
DC CURRENT(A)
Proprietary and Confidential
Document of Superworld
18/04/2016
P5
High Current Power Inductor– PIF0603A Series
8. Soldering:
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the
stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our
terminations are suitable for all re-flow soldering systems. If hand soldering cannot be avoided, the preferred
technique is the utilization of hot air.
8-1 Solder Re-flow:
Recommended temperature profiles for re-flow soldering in Figure 1.
8-2 Soldering Iron (Figure 2):
Products attachment with soldering iron is discouraged due to the inherent process control limitations.
In the event that a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150°C.
b) 355°C tip temperature (Max.)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (Max.)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 4~5 secs.
Proprietary and Confidential
Document of Superworld
18/04/2016
P6
High Current Power Inductor– PIF0603A Series
9. Packaging Information:
9-1 Reel Dimension
Type
A(mm)
B(mm)
C(mm)
D(mm)
330
13”x16mm 16.4+2/-0 100±2 13.5+0.5/-0.2
9-2 Tape Dimension
.
Series Size Ao(mm) Bo(mm) Ko(mm) P(mm) W(mm) F(mm)
T(mm) D(mm)
PIF 0603A 6.8±0.1 7.0±0.1 3.3±0.1 12.0±0.1 16±0.3 7.5±0.1 0.35±0.05 1.5±0.1
9-3 Packaging Quantity
PIF
0603A
Chip / Reel
Inner box
1,000
2,000
Carton
8,000
Proprietary and Confidential
Document of Superworld
18/04/2016
P7
High Current Power Inductor– PIF0603A Series
9-4 Tearing Off Force
The force for tearing off cover tape is 10 to 130 grams in the
arrow direction under the following conditions
Room
Humidity
(%)
Tearing
Speed
mm/min
Room Temp.
Room atm
(hPa)
(℃)
5~35
45~85
860~1060
300
Application Notice:
1. Storage Conditions:
To maintain the solderabililty of terminal electrodes:
a) Recommended products should be used within 12 months from the time of delivery.
b) The packaging material should be kept where no chlorine or sulfur exists in the air.
2. Transportation:
a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.
b) Vacuum pick up is strongly recommended for individual components.
c) Bulk handling should ensure that abrasion and mechanical shock are minimized.
Proprietary and Confidential
Document of Superworld
18/04/2016
相关型号：
©2020 ICPDF网 联系我们和版权申明