IQ32050HZV50NRA [SYNQOR]
DC-DC Regulated Power Supply Module, 1 Output, 250W, Hybrid, HALF BRICK PACKAGE-10/8;型号: | IQ32050HZV50NRA |
厂家: | SYNQOR WORLDWIDE HEADQUARTERS |
描述: | DC-DC Regulated Power Supply Module, 1 Output, 250W, Hybrid, HALF BRICK PACKAGE-10/8 局域网 |
文件: | 总19页 (文件大小:3486K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Technical
Specification
IQ32xxxHZXxx
9-75V
100V
5.0-50V
Outputs
255W
Max Power
2250V dc
Half-brick
DC-DC Converter
Continuous Input Transient Input
Isolation
The InQor Half-brick Zeta converter series is composed
of next-generation, board-mountable, fixed switching
frequency dc-dc converters that use synchronous
rectification to achieve extremely high power conversion
efficiency. Each module is supplied completely encased to
provide protection from the harsh environments seen in
many industrial and transportation applications.
G
-
A
0
F
R
N
@
0
5
V
C
0
Z
5
H
0
V
5
7
0
-
2
3
5
Q
I
T
.
U
O
5
IN
9
Operational Features
• High efficiency, 92% at full rated load current
• Operating input voltage range: 9-75V
• Fixed frequency switching provides predictable EMI
• No minimum load requirement
• Optional: Active current share for parallel application
rotectioures
Mechanical Features
t under-vltage locut
put current lmit and short circuit protection
ve back bias lit
• Industry standard Half-brick pin-on
• Size: 2.386" x 2.486" x 0.512" (60.60 x 6mm)
• Total weight: 4.9 oz (139 g)
o-recoveroutput over-voltage protection
al shuown
• Flanged baseplate version av
Control Features
CONTENTS
• On/Off coned to inpuide
• Remote sense fovoltage
Page No.
• Wide output oltagtge of -50%10%
Family Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics (5.0 Vout) & Figures . . . . . . . . . . . . . . . . . . . 4
Electrical Characteristics (12 Vout) & Figures . . . . . . . . . . . . . . . . . . . . 5
Electrical Characteristics (15 Vout) & Figures . . . . . . . . . . . . . . . . . . . . 6
Electrical Characteristics (24 Vout) & Figures . . . . . . . . . . . . . . . . . . . . 7
Electrical Characteristics (28 Vout) & Figures . . . . . . . . . . . . . . . . . . . . 8
Electrical Characteristics (40 Vout) & Figures . . . . . . . . . . . . . . . . . . . . 9
Electrical Characteristics (50 Vout) & Figures . . . . . . . . . . . . . . . . . . . .10
Application Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Standards & Qualification Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Standard Mechanical Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Flanged Mechanical Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Safety Features
Pending
• 2250V, 30 MΩ intput iso
• UL 60950-1:23, baulation
• CAN/CSA-. 6091:2003
• EN60950-1:20fied by TUV
• CE Marked 2006/9w Voltage Directive
• IEC 61000-4-2
• RoHS compliant (see last ge)
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 1
Technical
Specification
IQ32xxxHZXxx
IQ32 FAMILY ELECTRICAL CHARACTERISTICS (all output voltages)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
ABSOLUTE MAXIMUM RATINGS
Min.
Typ.
Max. Units Notes & Cdition
Input Voltage
Non-Operating
Operating
Operating Transient Protection
Isolation Voltage
100
80
100
V
V
V
Connuou
Cntinuous
nsiesquare wav
Input to Output
Input to Base-Plate
Output to Base-Plate
Operating Temperature
2250
2250
2250
100
125
18
V dc
V dc
°C
C
-40
-55
-2
Baseplate temperature
Storage Temperature
Voltage at ON/OFF input pin
INPUT CHARACTERISTICS
Operating Input Voltage Range
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Input Over-Voltage Shutdown
Recommended External Input Capacitance
Input Filter Component Values (L\C)
DYNAMIC CHARACTERISTICS
Turn-On Transient
9
75
V
9.4
7.6
10.1
8.3
1.8
9
V
V
V
V
µF
See No2
-
Not A
Tpical E0.2 Ω
µF Internal valFigure C
Turn-On Time
45
3
500
ms
%
ms
Vout=90% nom.; See Note 3
See Application Section
Output Voltage Overshoot
Auto-recovery Startup Inhibit Time
ISOLATION CHARACTERISTICS
Isolation Voltage (dielectric
Isolation Resistance
See Absolute Maximum Ratings
See Note 1
MΩ
pF
Isolation Capacitance o outpu
TEMPERATURE LIMIOWERATING CURVES
Semiconductor Junction Tee
Board Tempure
Transformture
Maximum Baserature, T
FEATURE CHARAC
25
5
125
100
°C
°C
°C
°C
Package rated to 150 °C
UL rated max operating temp 130 °C
Switching Frequency
ON/OFF Control
Off-State Voltage
On-State Voltage
230
0
250
kHz
V
Isolation stage switching freq. is 1/4 this
2.4
-2
18
0.8
ON/OFF Control
Pull-Up Voltage
Pull-Up Resistance
Over-Temperature Swn OTP int
Over-Temperature ShuRestart sis
RELIABILITRACSTICS
Calculated MTBrdiaTR-NWT-000332
Calculated MTBF () MIL-HDBK-217F
Field Demonstrated M
Application notes Figure A
Average PCB Temperature
5
10
125
10
V
kΩ
°C
°C
6
6
6
1.44
1.2
10 Hrs. Tb = 70°C
10 Hrs. Tb = 70°C
10 Hrs. See our website for details
Note 1: Higher values of iscapacitance can be added external to the module
Note 2: After passing turn-ovoltage, unit will operate down to turn-off voltage threshold
Note 3: Add 25ms to Turn-On time for full-featured units to allow for synchronization
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 2
Technical
Specification
IQ32xxxHZXxx
Family Figures (all output voltages)
120
100
80
60
40
20
Nominal Vout
Typical Current Limit Inon Poin
Tical Output Voltage at
Vin min
Vin nom
Vin max
0 30 40 50 60 70 90 100 130 150
Load Curr
Common Figure 1: Typical startup waveform. Input voltage pre-applied, ON/
OFF Pin on Ch 2.
Common Figurt voltage vad curring typicurrent limit
rves and converter shutdown po
Common Figure 3: Trim graph p 5.0 5V outputs.
mon Figure 4: Trim graph for trim-up 24 to 50V outputs.
Common Figure 5: Trim trim down.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 3
Input:9-75V
Output:5.0V
Current:50A
Part No.:IQ32050HZx50
Technical Specification
IQ32050HZx50 ELECTRICAL CHARACTERISTICS (5.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
44.0
560
8
A
mA
mA
V
Vin mintrim upnt limit
450
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
1.2
1.5
re 6
RM
50
A
Fast acnal fuse recommend
4.92
5
5.07
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-125
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
4.850
5
Over same, line, emperature & life
2bandwidth; se
Full
100
200
0
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Voltae
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outrrent (µs)
Settling Time
0
50
Subject to therating
utput voltage 0% Low
e 2
57.0
63.
2
67.0
V
20
3
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
4
mA
µF
0000
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
6.0
10
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
6.3
6.5
Over full temp range
100% Load
87
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 F ceram5 µF loR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQopplications support (e-maort@nqor.com)
Note 2: If the output voltage fs below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
Note 3: Line and load reguls limited by duty cycluantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 4
Input:9-75V
Output:12V
Current:21A
Part No.:IQ32120HZx21
Technical Specification
IQ32120HZx21 ELECTRICAL CHARACTERISTICS (12.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
43.0
8
A
mA
mA
V
Vin mintrim upnt limit
420
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
2.8
1.8
re 6
RM
50
A
Fast acnal fuse recommende
11.8
12
12.17
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-300
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
11.640
1
Over sampe, line, mperature & life
2bandwidth; se
Full l
100
200
0
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Volta
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outprrent (µs)
Settling Time
0
21
Subject to therating
utput voltage 0% Low
e 2
23.1
25.
4.8
6
27.3
V
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
3
4
mA
µF
000
1.
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
14.
15.0
15.6
Over full temp range
100% Load
89
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 cerami5 µF loR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQopplications support (e-maort@nqor.com)
Note 2: If the output voltage fs below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
Note 3: Line and load regullimited by duty cycle uantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 5
Input:9-75V
Output:15V
Current:17A
Part No.:IQ32150HZx17
Technical Specification
IQ32150HZx17 ELECTRICAL CHARACTERISTICS (15.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
41.0
560
8
A
mA
mA
V
Vin mintrim upnt limit
450
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
3.1
1.7
re 6
RM
50
A
Fast acnal fuse recommende
14.75
15
15.21
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-375
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
14.550
1
Over sampe, line, mperature & life
2bandwidth; se
Full l
80
160
0
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Volta
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outprrent (µs)
Settling Time
0
17
Subject to therating
utput voltage 0% Low
e 2
18.7
20.
22.1
6
6
3
V
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
4
mA
µF
000
2
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
17.
18.5
19.2
Over full temp range
100% Load
89
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 cerami5 µF loR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQopplications support (e-maort@nqor.com)
Note 2: If the output voltage fas below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
with a 500ms off-time
Note 3: Line and load regulamited by duty cycle quantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 6
Input:9-75V
Output:24V
Current:10A
Part No.:IQ32240HZx10
Technical Specification
IQ32240HZx10 ELECTRICAL CHARACTERISTICS (24.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
43.0
8
A
mA
mA
V
Vin mintrim upnt limit
TBD
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
TBD
TBD
re 6
RM
50
A
Fast acnal fuse recommende
23.60
24
24.34
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-600
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
23.280
2
Over sampe, line, mperature & life
2bandwidth; se
Full l
TBD
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Volta
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outprrent (µs)
Settling Time
0
10
Subject to therating
utput voltage 0% Low
e 2
11.0
12.
9.6
5
13.0
V
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
3
4
mA
µF
TBD
TB
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
28.
29.5
30.7
Over full temp range
100% Load
TBD
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 cerami5 µF loR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQopplications support (e-maort@nqor.com)
Note 2: If the output voltage fas below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
with a 500ms off-time
Note 3: Line and load regulamited by duty cycle quantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 7
Input:9-75V
Output:28V
Current:9.0A
Part No.:IQ32280HZx09
Technical Specification
IQ32280HZx09 ELECTRICAL CHARACTERISTICS (28.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
40.2
530
8
A
mA
mA
V
Vin mintrim upnt limit
425
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
5
re 6
1.6
RM
50
A
Fast acnal fuse recommende
27.54
28
28.39
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-700
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
27.300
2
Over sampe, line, mperature & life
2bandwidth; se
Full l
150
300
0
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Volta
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outprrent (µs)
Settling Time
0
9
Subject to therating
utput voltage 0% Low
e 2
9.9
10.
11.2
4
11.7
V
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
3
4
mA
µF
000
2.
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
33.
34.4
35.8
Over full temp range
100% Load
90
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 cerami5 µF loR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQopplications support (e-maort@nqor.com)
Note 2: If the output voltage fas below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
with a 500ms off-time
Note 3: Line and load regulamited by duty cycle quantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 8
Input:9-75V
Output:40V
Current:6.0A
Part No.:IQ32400HZx06
Technical Specification
IQ32400HZx06 ELECTRICAL CHARACTERISTICS (40.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
43.0
8
A
mA
mA
V
Vin mintrim upnt limit
TBD
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
TBD
TBD
re 6
RM
50
A
Fast acnal fuse recommende
39.34
40
40.56
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-1000
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
38.800
4
Over sampe, line, mperature & life
2bandwidth; se
Full l
TBD
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Volta
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outprrent (µs)
Settling Time
0
6
Subject to therating
utput voltage 0% Low
e 2
6.6
7.2
16
7.8
V
TBD
TBD
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
mA
µF
TBD
TB
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
47.
49.2
51.2
Over full temp range
100% Load
TBD
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 cerami5 µF loR tantalum capacitors. For applications requiring reduced output voltage ripple and
noise, consult SynQopplications support (e-maort@nqor.com)
Note 2: If the output voltage fas below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
with a 500ms off-time
Note 3: Line and load regulamited by duty cycle quantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 9
Input:9-75V
Output:50V
Current:5.0A
Part No.:IQ32500HZx05
Technical Specification
IQ32500HZx05 ELECTRICAL CHARACTERISTICS (50.0 Vout)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 32V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
Max. Units Notes & Cditio
INPUT CHARACTERISTICS
Maximum Input Current
No-Load Input Current
40.3
500
8
A
mA
mA
V
Vin mintrim upnt limit
400
5
Disabled Input Current
Response to Input Transient
Input Terminal Ripple Current
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
7.4
1.6
re 6
RM
50
A
Fast acnal fuse recommende
49.18
50
50.70
V
See Ne 3
±0.25
±0
%
mV
V
Over Load
Over Temperature
-1250
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
48.500
5
Over sampe, line, mperature & life
2bandwidth; se
Full l
200
400
0
5
mV
mV
RMS
Fll load
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Volta
Back-Drive Current Limit while Enable
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
Output Voltage during Load Cusient
Step Change in Outprrent (µs)
Settling Time
0
Subject to therating
utput voltage 0% Low
e 2
5.5
6.0
20
2
6.5
V
A
egcurrent drawn from output
Negative current drawn from output
ut nominal at full load (resistive load)
3
4
mA
µF
330
3
mV
ms
%
%
V
50% to 75% to 50% Iout max
To within 1% Vout nom
Output Voltage Trim Range
Output Voltemote Sense
Output Oveotection
EFFICIENCY
0
Across Pins 8&4; Common Figures 3-5;
Across Pins 8&4
60.
62.5
64.5
Over full temp range
100% Load
90
%
%
See Figure 1 for efficiency curve
See Figure 1 for efficiency curve
50% Load
Note 1: Output is teminated with 1 ceramiitor. Fplications requiring reduced output voltage ripple and noise, consult SynQor applications
support (e-mail: supt@synqor.com)
Note 2: If the output voltage fas below the Output rent Limit Shutdown Voltage for more than 50ms, then the unit will enter into hiccup mode,
with a 500ms off-time
Note 3: Line and load regulamited by duty cycle quantization and does not indicate a shift in the internal voltage reference
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 10
Technical
Specification
IQ32xxxHZXxx
Application Section
BASIC OPERATION AND FEATURES
CONTROL FEATURES
The converter series uses a two-stage power conversion topology.
The first stage keeps the output voltage constant over variations in
line, load, and temperature. The second stage uses a transformer
to provide the functions of input/output isolation and voltage step-
down to achieve the low output voltage required.
REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits
the user to control when the convertor off. This input is
referenced to the return terminaf the i, Vin(-).
The ON/OFF signal is active low ng thaw voltage turns
the converter on). Figure details ssible uits for driving
the ON/OFF pin.
Both the first stage and the second stage switch at a fixed frequency
for predictable EMI performance. Rectification of the transformer’s
output is accomplished with synchronous rectifiers. These devices,
which are MOSFETs with a very low on-state resistance, dissipate
significantly less energy than Schottky diodes, enabling the
converter to achieve high efficiency.
REMOTE SENSE(Pins 8 and 6)e SENSE) inputs
correct for voltagalong the conductors that connect the
converter’s otput piload.
Pin 8 should be connecVout(+) and Pin
conned to Vout(-) at the on the board where regulat
is desIf these connectns are not , the converter
will den output oltage that slighher than its
pecifie
The series of half-brick, quarter-brick and eighth-brick converters
uses the industry standard footprint and pin-out configuration.
Note: The outr-voltage tectiosensehe voltage
ss the sense leads (pins 8 ) to dee whn it should
the voltage aoss thverter’s out pins (pins 9
and
ON/OFF
ON/OFF
_)
OUTPUT VOLTAGE (Pin 7): ThIM input permits the
usr to adjust thoutpage across the sense leads up or
don according to the trge specifications. SynQor uses
industry stard trim equatio
Vin(_)
Remote Enable Circuit
To decrease tut voltage, the user should connect a resistor
between Pin 7 (Td Pin 6 (SENSE(–) input). For a desired
dese of the noiput voltage, the value of the resistor
should be:
Negve Logi
(Permy Enabed)
ON/OFF
TTL/
MOS
O
Vin(_)
Rtrim-down = (100% )- 2kΩ
Δ
e
Vnominal – Vdesired
ector Enable it
DireDrive
Δ% =
|
|
x 100%
Vnominal
Figure A: Varios circuig the ON/OF pin.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 11
Technical
Specification
IQ32xxxHZXxx
Application Section
Protection Features
To increase the output voltage, the user should connect a
resistor between Pin 7 (TRIM) and Pin 8 (SENSE(+) input). For a
desired increase of the nominal output voltage, the value of the
resistor should be
Input Under-Voltage Lockout: The converter is designed to
turn off when the input voltage is helping to avoid an
input system instability problemwhich ed in more detail
in the application note titled Istem Iy on the SynQor
website. The lockout circuitry is arator DC hysteresis.
When the input voltage rising, ixceehe typical Turn-
On Voltage Threshold value* before nverter will turn on.
Once the converteon, e input vomust fall elow the
typical Turn-Off Throld value efore the converter will
turn off.
Vnominal
1.225
(
- 2
)
x
V
V
DES +
VNOM
Rtrim-up =
kΩ
VDES –
NOM
Trim graphs show the relationship between the trim resistor
value and Rtrim-up and Rtrim-down, showing the total range the
output voltage can be trimmed up or down.
Output Curret Limit: utput current exct
DC Cuent Limit Inception*, then a fast linear curr
contrwill reduce the ouut voltagmaintain a constant
outpuent. If as a esult, the ouput vfalls below the
Outpurrent Limt Shutdown ltage”ore th50
ms, then will enter into hiccde, wi00 ms off-
time. The unen automcally ato res.
Note: The TRIM feature does not affect the voltage at which the
output over-voltage protection circuit is triggered. Trimming the
output voltage too high may cause the over-voltage protection
circuit to engage, particularly during transients.
ve Current Limit: Ie is negoutput current
ude larger thathe Drive Current Limit while
Enabled” specificatithen a fast ive limit controller will
increase the output vto maintain stant output current.
If his results in e ouoltage exceding the “Output Over-
Votage Protection” threshhen the unit will shut down. The
full I-V oucharacteristics seen in Figure 15.
It is not necessary for the user to add capacitance at the Tri
The node is internally filtered to eliminate noise.
Total DC Variation of Vout: For the converter teet its full
specifications, the maximum variation of the DC Vout,
due to both trimming and remote load voltage dropsot
be greater than that specified for the output voltage trim
Output Overe Limit: If the voltage across the output
piexceeds the Over-Voltage Protection threshold, the
conveter will mmediastop switching. This prevents damage
to the load circuit due to 1) excessive series resistance in output
urrent path from converter output pins to sense point, 2) a
ase of a short-circuit condition, or 3) a release of a current
onditionLoad capacitance determines exactly how high
tht voltage will rise in response to these conditions. After
500ms the converter will automatically restart for all but S Feature
t option, which is latching and will not restart until input power
led or the ON/OFF input is toggled.
Over-Temperature Shutdown: A temperature sensor on
the converter senses the average temperature of the module.
The thermal shutdown circuit is designed to turn the converter
off when the temperature at the sensed location reaches the
“Over-Temperature Shutdown” value*. It will allow the converter
to turn on again when the temperature of the sensed location
falls by the amount of the “Over-Temperature Shutdown Restart
Hysteresis” value*.
* See Electrical Characteristics page.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 12
Technical
Specification
IQ32xxxHZXxx
Application Section
APPLICATION CONSIDERATIONS
Thermal Considerations: The maximum operating base-plate
temperature, TB, is 100 ºC. As long as the user’s thermal system
keeps TB < 100 ºC, the converter r its full rated power.
Input System Instability: This condition can occur because any
DC-DC converter appears incrementally as a negative resistance
load. A detailed application note titled “Input System Instability” is
available on the SynQor website which provides an understanding
of why this instability arises, and shows the preferred solution for
correcting it.
A power derating curve can bulated heatsink that is
attached to the base-plate of erter. ly necessary to
determine the thermal resistance, of thosen heatsink
between the base-plaanthe aair fa given airflow
rate. This information is usually availabhe heatsink vendor.
The following foran thbe used to ermine thmaximum
power the convertissipate fa given thermal condition if
its base-platis to bher tha00 ºC.
Application Circuits: Figure B below provides a typical circuit
diagram which details the input filtering and voltage trimming.
Input Filtering and External Input Capacitance: Figure
C below shows the internal input filter components. This filter
dramatically reduces input terminal ripple current, which otherwise
could exceed the rating of an external electrolytic input capacitor.
The recommended external input capacitance is specified in the
Input Characteristics section on the Electrical Specifications page.
More detailed information is available in the application note titled
EMI Characteristics on the SynQor website.
To increase the output voe user should conn
betwePin 7 (TRIM) and (SENSE(+) input). For a des
increaf the nominal outpt voltage, tue of the resistor
should
10ºC - TA
RTHBA
=
s value of power dissipathen ed in onjunction
ata shown in Fgure termine maximum load
cupower) that te concan deliver in the given
thermal condition.
Output Filtering and External Output Capacitance:
C below shows the internal output filter components. This filter
dramatically reduces output voltage ripple. However, some
minimum external output capacitance is required, aspecified in
the Output Characteristics section on the Electrications
page. No damage will occur without this capacitor cout
peak output voltage ripple will be much higher.
Fr conveniencFigand 4 povide Power derating
cuves for an encased cer without a heatsink and with
a typical tsink.
)
Vout(+)
Vsense(+)
ctrolytic
citor
rnal
ut
Filter
Rtrim-up
Trim
or
O/OFF
Vin(_)
Cload
Rtrim-down
Iload
Vsense(_)
Vout(_)
Figure B: Typical appation circuit (negative logic uanely enabled).
n
Vin(+)
Vout(+)
Vout(-)
Regulation
Stage
Current
Sense
Isolation
Stage
C1
C2
Vin(_)
Figure C: Internal Input and t Filter Diagram (component values listed on
specifications page).
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 13
Technical
Specification
IQ32xxxHZXxx
Application Section
Full-Featured Application Notes
Withthefull-featuredoption, specifiedbyan“F”inthelastcharacter
in the part number, current sharing operation is supported, adding
two additional pins: SHARE(+) and SHARE(-)
• Input power pins and output power pins should be tied
together between units, preferably e overlapping copper
planes.
• The SHARE(+) and SHARE(shoulted between all
paralleled units as a differentia
• The ON/OFF pins shoube conn paral, and rise/fall
times should be kept below 2ms.
• The SENSE(+) anSENSE(-) pins shoconnecteeither
locally at each uparly to a comon sense point.
• If the TRIM pin ihen each nit should have its own
trim resistor nnectebetwn TRIM a+) or
SENSE(-).
Connection of Paralleled Units: Up to 100 units can be placed in
parallel. In this current share architecture, one unit is dynamically
chosen to act as a master, controlling all other units. It cannot be
predicted which unit will become the master at any given time, so
units should be wired symmetrically (see fig D).
Vin(+)
V)
>470nH
F
Sense
On/Off
Load
Trim
Share (
Share (-)
Electrolytic
Capacitor
n(-)
Sense
Vout(-)
Vin(
out(+)
>470nH
Sense (+)
On/Off
Shar
rim
Share (-
Electc
apacir
Sense (-)
Vout(-)
(-)
to 100 Units
Vin(+)
On/Off
Vout(+)
>470nH
Sense (+)
Trim
Share (+)
Share (-)
Electrolytic
Capacitor
Sense (-)
Vout(-)
Vin(-)
Figure D: Typical application rcuit for parallelling of full-featured units
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 14
Technical
Specification
IQ32xxxHZXxx
Application Section
RS-485 Physical Layer: The internal RS-485 transceiver includes
many advanced protection features for enhanced reliability:
Automatic Configuration: The micro-controller inside each
power converter unit is programmed at the factory with a unique
chip number. In every other respect, each shared unit is identical
and has the same orderable part number.
• Current Limiting and Thermal Shutd
Driver Overload Protection
• IEC61000 ESD Protection t.5kV
• Hot Plug Circuitry – SHARE(+) ARE(-
Outputs Remain Tri-SDuring p/Poer-down
On initial startup (or after the master is disabled or shuts down),
each unit determines the chip number of every other unit currently
connected to the shared serial bus formed by the SHARE(+) and
SHARE(-) pins. The unit with the highest chip number dynamically
reconfigures itself from slave to master. The rest of the units (that
do not have the highest chip number) become slaves.
Internal SchottkDiode TerminDespite signaling
at high speed st ees, externtermination resistors
are not necessaryeceiver hfour Schottky diodes built
in, two for ch line ifferenl pair. Ths clamp
any ringing caued by ssion line reflectio
the voage from going abbout 5.5 V or below abou
V. Anbsequent ringing tn inherenes place between
4.5 anV or betwen -0.5 and 05 V. Sch receiver on
he buns a set f clamping es to any pible
transmisseflection, the bus dot necily need to
be routed as -chain.
The master unit then broadcasts its control state over the shared
serial bus on a cycle-by-cycle basis. The slave units interpret and
implement the control commands sent by the master, mirroring
every action of the master unit.
If the master is disabled or encounters a fault condition, all units
will immediately shut down, and if the master unit is unable to
restart, then the unit with the next highest chip number will
become master. If a slave unit is disabled or encounters a f
condition, all other units continue to run, and the slave un
restart seamlessly.
RE(+) and SHARE(-refereo Vin(-), and
hould be roued as ferential pair near the
Vin(-) plane for optsignal intege maximum difference
in voltage between Vins of all unithe share-bus should
bkept within 3V tent steadytate conduction of the
temination diodes. Theree Vin(-) connections to each unit
must be cmon, preferably ted by a single copper plane.
Automatic Interleaving: The slave units automatically lock
frequency with the master, and interleave the of their
switching transitions for improved EMI performancethe
phase angle relative to the master, each slave divides 36
by the total number of connected units, and multiples he res
its rank among chip numbers of connected units.
Share Accunside each converter micro-controller, the
duty cycle is gendigitally, making for excellent duty cycle
maing betweected units. Some small duty cycle
mismatch is caused by well controlled) process variations in the
MOSFET gate drvers. However, the voltage difference induced
this duty cyclmismatch appears across the impedance of
ntire poer converter, from input to output, multiplied by
te the differential current flows out of one converter and
into ar. So, a small duty cycle mismatch yields very small
ifferential currents, which remain small even when 100 units are
ed in parallel.
ORing Diodes placed in series withe conerter outpts must
also have a resistor smaller than 5placed in parallThis
resistor keeps the output voltage orily disabled slave
unit consistent with the active master unoutput voltage
of the slave unit were allototally dischand the slave
unit tried to restart, it would fse the slave reproduche
duty cycle of the manit, wnning in steady stat
cannot repeat an ouage sot.
Common Mode Filterit be her a singprimary side
choke handlg the inputs fhe paralleled or multiple
chokes plthe seconde. This ensura solid
Vin(-) plane ied betwen units.
Iother current-sharing schemes, it is common to have a current-
sharing control loop in each unit. However, due to the limited
bandwidth of this loop, units do not necessarily share current
on startup or during transients before this loop has a chance to
respond. In contrast, the current-sharing scheme used in this
product has no control dynamics: control signals are transmitted
fast enough that the slave units can mirror the control state of
the master unit on a cycle-by-cycle basis, and the current simply
shares properly, from the first switching cycle to the last.
Resonance betwut Capaitors ossible:
multiple units are paraed, it is ble tee a ses
resonance betwen the output capacin two and the
air core inductors formed by toutput This ispecially
likely at higher ouput voltages where the rd cpacitance
is relatively small. The oblem is indepenof external
output capacitance. To e that this resont frequency is
below the switching frequer output oltages above 18V, it
is recommended td at le0nH oinductance in series
with each converteut. Tuld comprise the leakage
inductance of condide comn mode choke.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 15
Technical
Specification
IQ32xxxHZXxx
Standards & Qualification Testing
Parameter
Notes & Conditions
STANDARDS COMPLIANCE
UL 60950-1 2nd Ed. 2007
CAN/CSA-C22.2 No. 60950-1:2003
EN60950-1:2001
Pending
Basic Insulation
Certified by TUV
CE Marked
2006/95/EC Low Voltage Directive
ESD test, 8 kV - NP, 15 kV air - NP (Normal Pmanc
IEC 61000-4-2
Note: An external input fuse must always be used to meet these safety requirements. Contact Sofficafety certifiates on new
releases or download from the SynQor website.
Parameter
QUALIFICATION TESTING
Life Test
# Units Test Contions
32
5
95% in and load, units at derating poi0 hour
Vibration
1total excursion, 1 min./s120 sweaxis
100g minimum, 2 , y, and z xis
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
5
1
-40 °C to 10 °C, unit temp. ramp in., 500 cycle
operating = mn to max, Vin = in to ll load, 100 ccles
0 °C to Tmax+10 °C, 5 °C steps, Vin to max, 0-105% load
8H, 1000 hontinuous Vin apxcept 5 min/day
5
5
Solderability
15 pins MIL-ST83, method 2003
70,000 feet (21 m), see Nte
Altitude
2
Note: A conductive cooling design is eeded for high altde applications bcause of natually convective cooling at rare atmospheres.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 16
Technical
Specification
IQ32xxxHZXxx
Standard Mechanical Diagram
2.486 .020 [63.14
0.5]
2.00 [50.8 ]
1.400 [35.56 ]
1.000 [25.4 ]
.700 [17.78 ]
.400 [10.16 ]
IDE VIEW
+.002
-.005
+
.512
.163
[4.14 ]
13
[
OVE
HEIG
.243 .020
[6.17 0.5]
9
8
7
6
5
.020
[6.17 0.5]
2.386 .020
[60.6
0.5]
TOP VIEW
1.90
[48.3 ]
1.90
[48.3 ]
.233 .020
[5.92
0.5]
1
2
B
3
4
+.007
.027
THRU HOLE
M3 (SEE NOTE 8)
STAFFS (4)
-.010
+0.17
[10.16 ]
69
-0.25
]
32 ]
1.00 25.4 ]
OMSIDE CLEARANCE
.543 .020
[13.79 0.5]
1.400 [35.56
NOTES
PIN DESIGNATIONS
Pin
Name
Vin(+
Function
1)
2)
3)
Applied torque per screw should not excee0.7 Nm).
B
Positive input voltage
Baseplate flatness toleran4” (.10 mm) TIfor surfac
TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
ON/OF
Pins 1-4, 6-8, and 0.040m) diameter, with 0.08
(2.03mm) diamoff sho
SHARE(+)
Active current share differential pair
(See note 4)
4)
Pins 5 and 9 are 0.0mm) eter with 0.15”
(3.18 mm) diameter stoulde
5
6
7
8
9
SHARE(-)
Vin(–)
Vout(–)
SENSE(–)
TRIM
Negative input voltage
Negative output voltage
Negative remote sense (See note 1)
Output voltage trim(See note 2)
Positive remote sense (See note 3)
Positive output voltage
5)
6)
7)
8)
9)
All Pinerial - Copper nish - Matte Tin ickel plate
Undimeponents ahown for visual refery.
Weight: 4.9 oz
SENSE(+)
Vout(+)
Threaded nd Nn-Ted optionlable
All dimensionin inches (mm).
Tolerances:
Notes:
1)
SENSE(–) should be connected to Vout(–) either remotely or at the converter.
x.xx +/-0.02 . (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.x+/-0.25mm)
unless otherwise not
2)
3)
Leave TRIM pin open for nominal output voltage.
SENSE(+) should be connected to Vout(+) either remotely or at the
converter.
11) Workmanship: Meets os IPC-A-610C Class II
4)
Full-Featured option only. Pin 3 and Pin B not populated on standard model.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 17
Technical
Specification
IQ32xxxHZXxx
Flanged Mechanical Diagram
.18 [4,6 ]
SEE NOTES 5 & 6
.500
[12,7
.025
0,63]
OVERALL
HEIGHT
.01 [0,2]
[
.125
[3,18 ]
1.400
1.000 [2
0 [17,78 ]
10,16 ]
3.15 [80 ]
USE W/ 4-40 OR
M3 SCREW (6x)
RECOM. TORQUE
3 in.lb
2.486 .020 [63,14
0,5]
6
9
.13[3,3]
1.900
[48,26 ]
OM VIEW
TOP VIEW
1.61
[40,9 ]
.31
[7,9 ]
.96
[24,4 ]
3
B
2
1
.027 0
.400 [10,16 ]
.800 [20,32 ]
1.000 [25,4 ]
1.400 [35,56 ]
[0,6
.543
,5]
0,5]
0,5]
.775 .020 [1
.875 .020 [22,23
2.175 .020 [55,25
0,5]
NOTES
1)
PIN DESIGNATIONS
n
Name
Vin(+)
Function
Positive input voltage
Applied torque per scrnot eeed 5in-lb. 7 Nm)
2
B
(3in-lb. ommended).
2)
3)
Baseess tolerance (.25 mm) TIR fce.
TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
ON/OFF
Pins 1-4, e 0.040” 1.02mm) der, with
(2.03mm) diaff shoulders.
Pins 5 and 9 are .0.03 mm) deter w0.125”
(3.18 mm) ameter sndoff should
All Pins: Mateal - Copper AlloyFinish Tin ovkel plate
Undimensioned omponents are shown for feree only.
Weight: 4.8oz (137g)
SHARE(+)
Active current share differential pair
(See note 4)
4)
3
4
5
6
7
8
9
SHARE(-)
Vin(–)
Vout(–)
SENSE(–)
TRIM
Negative input voltage
Negative output voltage
Negative remote sense (See note 1)
Output voltage trim(See note 2)
Positive remote sense (See note 3)
Positive output voltage
5)
6)
7)
9)
SENSE(+)
Vout(+)
All dimensions in inche
Tolerances:
Notes:
1)
x.xx +/-0.02 x +/-0.
x.xxx +/-0.010 x +/-0
unless owise n
SENSE(–) should be connected to Vout(–) either remotely or at the converter.
2)
3)
Leave TRIM pin open for nominal output voltage.
10) Workmeets exceeds IPC-A-610C Class II
SENSE(+) should be connected to Vout(+) either remotely or at the
converter.
4)
Full-Featured option only. Pin 3 and Pin B not populated on standard model.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 18
Technical
Specification
IQ32xxxHZXxx
PART NUMBERING SYSTEM
ORDERING INFORMATION
The part numbering system for SynQor’s dc-dc converters follows the format
shown in the example below.
The tables below show the valid model numbers and ordering options for
converters in this product family. When nQor converters, please
ensure that you use the complete 1charaumber consisting of
the 12 character base part number e additacters for options.
Add “-G” to the model number for compl
IQ 32 050 H Z C 50 N R S - G
Input
Voltage
put
Max Output
Current
Model Number
6/6 RoHS
Options (see
IQ32050HZw50x
IQ32120HZ21xyz
IQ32150Hxyz
IQ3220HZw10xyz
IQ32HZw09xyz
IQ32w06xyz
Q3255xyz
9-75 V
-75 V
V
9-V
9-75 V
9-75 V
50 V
12 V
15 V
24 V
2
40
50 V
50 A
21 A
1
9 A
Ordering Information)
Output Current
Thermal Design
Performance Level
Package Size
6 A
5 A
Output Voltage
Input Voltage
Product Family
ng options must be includace of ty z spaces in the
s listed above.
The first 12 characters comprise the base part number and the last 3
characters indicate available options. The “-G” suffix indictes 6/6 RoHS
compliance.
ptions Descr
Enable
Thermal Dign
Pin tyle
Feature Set
ogic
C Encased
D - Encased h Non-Threaded
Baseplate
V - Encased d
Baseplate
Application Notes
A - Standard
F - Full-Feature
N - ve R - 0.180"
A variety of application notes and technical white ppers can be owloade
in pdf format from our website.
RoHS Compliance: The EU estriction of Hardous
Substances) Directive bans the use omium, Hexavalent
Chromium, Mercury, Polybrominated Biphenyls Polybrominated
Diphenyl Ether (PBDE) in ElecElectronic Equ. This SynQor
product is 6/6 RoHS compliant. re information please rto
l combinaons make valid part numbers, please contact SynQor for
ay. See he Product Summary web page for more options.
SynQor’s RoHS addendailable oHS Compliance /
Free Initiative web -mail ohs@synqor.com
.
TENTS
SQor holds the following U.S. patents, one or more of which apply to
each product listed in this document. Additional patent applications may
be pending or filed in the future.
5,999,417
6,896,526
7,272,021
6,222,742
6,927,987
7,272,023
6,545,890
7,050,309
7,558,083
6,577,109
7,072,190
7,564,702
6,594,159
7,085,146
7,765,687
6,731,520
7,119,524
7,787,261
6,894,468
7,269,034
8,023,290
Contact SnQor for further inatin:
Phone:
Toll Free: 567-9596
78-849-0600
Warranty
SynQor offers a two (2) year limited warranty. Complete warranty
information is listed on our website or is available upon request from
SynQor.
Fax:
E-mail
:
979-0602
powenqor.com
www.synqor.com
Ad: 155 Swanson Road
Boxborough, MA 01719
SA
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
Product # IQ32xxxHZXxx
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006151 Rev. 3
01/27/12
Page 19
相关型号:
IQ32050HZV50NRA-G
DC-DC Regulated Power Supply Module, 1 Output, 250W, Hybrid, HALF BRICK PACKAGE-10/8
SYNQOR
IQ32050HZV50NRF
DC-DC Regulated Power Supply Module, 1 Output, 250W, Hybrid, HALF BRICK PACKAGE-10
SYNQOR
IQ32050HZV50NRF-G
DC-DC Regulated Power Supply Module, 1 Output, 250W, Hybrid, HALF BRICK PACKAGE-10
SYNQOR
IQ32050QGV10NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32050QTC17NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32050QTD17NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32050QTV17NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32070QGC07NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32070QGV07NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 50W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32070QTC12NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
IQ32070QTD12NRS-G
DC-DC Regulated Power Supply Module, 1 Output, 86W, Hybrid, ROHS COMPLIANT, QUARTER BRICK PACKAGE-8
SYNQOR
©2020 ICPDF网 联系我们和版权申明