VCA2616 [TAOS]
Dual, Variable-Gain Amplifier with Low-Noise Preamp; 双通道，可变增益放大器，具有低噪声前置放大器
| 型号： | VCA2616 |
| 厂家： | 
TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS |
| 描述： | Dual, Variable-Gain Amplifier with Low-Noise Preamp |
| 文件： | 总23页 (文件大小：1040K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
VCA2616
VCA2611
V
C
A
2
6
1
6
SBOS234E – MARCH 2002 – REVISED NOVEMBER 2004
Dual, Variable-Gain Amplifier
with Low-Noise Preamp
FEATURES
DESCRIPTION
● LOW-NOISE PREAMP:
The VCA2616 and VCA2611 are dual, Low-Noise Preamplifiers
(LNP), plus low-noise Variable Gain Amplifiers (VGA). The
VCA2611 is an upgraded version of the VCA2616. The only
difference between the VCA2616 and the VCA2611 is the input
structure to the LNP. The VCA2616 is limited to –0.3V negative-
going input spikes; the VCA2611 is limited to –2.0V negative-
going input spikes. This change allows the user to use slower
and less expensive input clamping diodes prior to the LNP input.
In some designs, input clamping may not be required.
– Low Input Noise: 0.95nV/√Hz
– Active Termination Noise Reduction
– Switchable Termination Value
– 80MHz Bandwidth
– 5dB to 25dB Gain
– Differential In and Out
● LOW-NOISE VARIABLE GAIN AMPLIFIER:
– Low-Noise VCA
The combination of Active Termination (AT) and Maximum
Gain Select (MGS) allow for the best noise performance. The
VCA2616 and VCA2611 also feature low crosstalk and out-
standing distortion performance.
– Up to 40dB Gain Range
– 40MHz Bandwidth
– Differential In and Out
● LOW CROSSTALK: 66dB at Max Gain, 5MHz
● HIGH-SPEED VARIABLE GAIN ADJUST
● SWITCHABLE EXTERNAL PROCESSING
The LNP has differential input and output capability and is
strappable for gains of 5dB, 17dB, 22dB, or 25dB. Low input
impedance is achieved by AT, resulting in as much as a 4.6dB
improvement in noise figure over conventional shunt termina-
tion. The termination value can also be switched to accommo-
date different sources. The output of the LNP is available for
external signal processing.
APPLICATIONS
The variable gain is controlled by an analog voltage whose
gain varies from 0dB to the gain set by the MGS. The ability
to program the variable gain also allows the user to optimize
dynamic range. The VCA input can be switched from the LNP
to external circuits for different applications. The output can be
used in either a single-ended or differential mode to drive high-
performance Analog-to-Digital (A/D) converters, and is cleanly
limited for optimum overdrive recovery.
● ULTRASOUND SYSTEMS
● WIRELESS RECEIVERS
● TEST EQUIPMENT
Maximum Gain Select
MGS1 MGS2 MGS3
FBCNTL
LNPOUT
N
VCAIN
N
VCACNTL
The combination of low noise, gain, and gain range program-
mability makes the VCA2616 and VCA2611 versatile building
blocks in a number of applications where noise performance
is critical. The VCA2616 and VCA2611 are available in a
TQFP-48 package.
RF2
RF1
FBSW
FB
VCA2616
(1 of 2 Channels)
Analog
Control
Maximum Gain
Select
Input
LNPINP
VCAOUT
N
LNPGS1
LNPGS2
Programmable
Gain Amplifier
24 to 45dB
Voltage
Controlled
Attenuator
Low Noise
Preamp
5dB to 25dB
LNP
Gain
Set
LNPGS3
LNPINN
VCAOUT
P
LNPOUTP VCAIN
P
SEL
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 2002-2004, Texas Instruments Incorporated
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
Power Supply (+VS) ............................................................................. +6V
VCA2616 Analog Input ............................................ –0.3V to (+VS + 0.3V)
VCA2611 Analog Input ............................................ –2.0V to (+VS + 0.3V)
Logic Input ............................................................... –0.3V to (+VS + 0.3V)
Case Temperature ......................................................................... +100°C
Junction Temperature .................................................................... +150°C
Storage Temperature ...................................................... –40°C to +150°C
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
PACKAGE/ORDERING INFORMATION(1)
SPECIFIED
PACKAGE
DESIGNATOR
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
PACKAGE-LEAD
VCA2616
TQFP-48
PFB
"
–40°C to +85°C
VCA2616
VCA2616YT
VCA2616YR
Tape and Reel, 250
Tape and Reel, 2000
"
"
"
"
VCA2611
TQFP-48
PFB
"
–40°C to +85°C
VCA2611
VCA2611Y/250
VCA2611Y/2K
Tape and Reel, 250
Tape and Reel, 2000
"
"
"
"
NOTE: (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet.
ELECTRICAL CHARACTERISTICS
At TA = +25°C, VDDA = VDDB = VDDR = +5V, load resistance = 500Ω on each output to ground, MGS = 011, LNP = 22dB and fIN = 5MHz, unless otherwise noted.
The input to the preamp (LNP) is single-ended, and the output from the VCA is single-ended, unless otherwise noted.
VCA2616Y, VCA2611Y
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
PREAMPLIFIER
Input Resistance
Input Capacitance
Input Bias Current
CMRR
600
15
1
50
1
112
4.2
0.95
0.35
6.2
kΩ
pF
nA
dB
VPP
mVPP
f = 1MHz, VCACNTL = 0.2V
Preamp Gain = +5dB
Preamp Gain = +25dB
Preamp Gain = +5dB
Preamp Gain = +25dB
Independent of Gain
Maximum Input Voltage
Input Voltage Noise(1)
nV/
nV/
pA/
√Hz
√Hz
√Hz
Input Current Noise
Noise Figure, RS = 75Ω, RIN = 75Ω(1)
RF = 550Ω, Preamp Gain = 22dB,
PGA Gain = 39dB
dB
Bandwidth
Gain = 22dB
80
MHz
PROGRAMMABLE VARIABLE GAIN AMPLIFIER
Peak Input Voltage
–3dB Bandwidth
Slew Rate
Output Signal Range
Differential
2
40
300
2
1
VPP
MHz
V/µs
VPP
Ω
RL ≥ 500Ω Each Side to Ground
Output Impedance
f = 5MHz
Output Short-Circuit Current
±40
–71
–63
–75
–75
–66
±2
mA
dBc
dBc
dBc
dBc
dB
3rd-Harmonic Distortion
2nd-Harmonic Distortion
IMD, 2-Tone
f = 5MHz, VOUT = 1VPP, VCACNTL = 3.0V
f = 5MHz, VOUT = 1VPP, VCACNTL = 3.0V
VOUT = 2VPP, f = 1MHz
VOUT = 2VPP, f = 10MHz
VCACNTL = 0.2V
1MHz < f < 10MHz, Full Gain Range
–45
–45
Crosstalk
Group Delay Variation
DC Output Level, VIN = 0
ns
V
2.5
ACCURACY
Gain Slope
Gain Error
10.9
dB/V
dB
±1(2)
Output Offset Voltage
Total Gain
±50
21
50
mV
dB
dB
VCACNTL = 0.2V
VCACNTL = 3.0V
18
47
24
53
GAIN CONTROL INTERFACE
Input Voltage (VCACNTL) Range
Input Resistance
0.2 to 3.0
V
MΩ
µs
1
0.2
Response Time
40dB Gain Change, MGS = 111
Operating, Both Channels
POWER SUPPLY
Operating Temperature Range
Specified Operating Range
Power Dissipation
–40
4.75
+85
5.25
495
°C
V
mW
5.0
410
NOTES: (1) For preamp driving VGA.
(2) Referenced to best fit dB-linear curve.
VCA2616, VCA2611
2
SBOS234E
www.ti.com
PIN CONFIGURATION
Top View
TQFP
48 47 46 45 44 43 42 41 40 39 38 37
VDD
A
1
2
3
4
5
6
7
8
9
36 VDD
35 NC
34 NC
B
NC
NC
VCAINNA
VCAINPA
LNPOUTNA
LNPOUTPA
SWFBA
FBA
33 VCAINNB
32 VCAINPB
31 LNPOUTNB
30 LNPOUTPB
29 SWFBB
28 FBB
VCA2616
VCA2611
COMP1A 10
COMP2A 11
LNPINNA 12
27 COMP1B
26 COMP2B
25 LNPINNB
13 14 15 16 17 18 19 20 21 22 23 24
PIN DESCRIPTIONS
PIN
DESIGNATOR
DESCRIPTION
PIN
DESIGNATOR
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VDD
NC
NC
A
Channel A +Supply
Do Not Connect
Do Not Connect
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
LNPINNB
COMP2B
COMP1B
FBB
SWFBB
LNPOUTPB
LNPOUTNB
VCAINPB
VCAINNB
NC
Channel B LNP Inverting Input
Channel B Frequency Compensation 2
Channel B Frequency Compensation 1
Channel B Feedback Output
Channel B Switched Feedback Output
Channel B LNP Positive Output
Channel B LNP Negative Output
Channel B VCA Positive Input
Channel B VCA Negative Input
Do Not Connect
Do Not Connect
Channel B +Analog Supply
Channel B Analog Ground
Channel B VCA Negative Output
Channel B VCA Positive Output
Maximum Gain Select 3 (LSB)
Maximum Gain Select 2
Maximum Gain Select 1 (MSB)
VCA Control Voltage
VCAINNA
VCAINPA
LNPOUTNA
LNPOUTPA
SWFBA
FBA
COMP1A
COMP2A
LNPINNA
LNPGS3A
LNPGS2A
LNPGS1A
LNPINPA
Channel A VCA Negative Input
Channel A VCA Positive Input
Channel A LNP Negative Output
Channel A LNP Positive Output
Channel A Switched Feedback Output
Channel A Feedback Output
Channel A Frequency Compensation 1
Channel A Frequency Compensation 2
Channel A LNP Inverting Input
Channel A LNP Gain Strap 3
Channel A LNP Gain Strap 2
Channel A LNP Gain Strap 1
Channel A LNP Noninverting Input
+Supply for Internal Reference
0.01µF Bypass to Ground
NC
V
DDB
GNDB
VCAOUTNB
VCAOUTPB
MGS3
MGS2
MGS1
VCACNTL
VCAINSEL
FBSWCNTL
VCAOUTPA
VCAOUTNA
GNDA
VDDR
VBIAS
VCM
GNDR
LNPINPB
LNPGS1B
LNPGS2B
LNPGS3B
0.01µF Bypass to Ground
Ground for Internal Reference
Channel B LNP Noninverting Input
Channel B LNP Gain Strap 1
Channel B LNP Gain Strap 2
Channel B LNP Gain Strap 3
VCA Input Select, HI = External
Feedback Switch Control: HI = ON
Channel A VCA Positive Output
Channel A VCA Negative Output
Channel A Analog Ground
VCA2616, VCA2611
3
SBOS234E
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25°C, VDDA = VDDB = VDDR = +5V, load resistance = 500Ω on each output to ground, MGS = 011, LNP = 22dB and fIN = 5MHz, unless otherwise noted.
The input to the preamp (LNP) is single-ended, and the output from the VCA is single-ended, unless otherwise noted. This results in a 6dB reduction in signal
amplitude compared to differential operation.
GAIN ERROR vs TEMPERATURE
GAIN vs VCACNTL
65
60
55
50
45
40
35
30
25
20
15
2.0
1.5
MGS = 100
MGS = 101
1.0
MGS = 110
MGS = 111
+85°C
+25°C
0.5
0.0
–0.5
–1.0
–1.5
–2.0
–40°C
MGS = 010 MGS = 011
MGS = 000
MGS = 001
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
GAIN ERROR vs VCACNTL
GAIN ERROR vs VCACNTL
2.0
1.5
2.0
1.5
1MHz
5MHz
10MHz
1.0
1.0
MGS = 011
MGS = 000
0.5
0.5
0.0
0
–0.5
–1.0
–1.5
–2.0
–0.5
–1.0
–1.5
–2.0
MGS = 111
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
GAIN MATCH
GAIN MATCH
3.0V CHA to CHB
0.2V CHA to CHB
50
45
40
35
30
25
20
15
10
5
60
50
40
30
20
10
0
0
Delta Gain (dB)
Delta Gain (dB)
VCA2616, VCA2611
4
SBOS234E
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDDA = VDDB = VDDR = +5V, load resistance = 500Ω on each output to ground, MGS = 011, LNP = 22dB and fIN = 5MHz, unless otherwise noted.
The input to the preamp (LNP) is single-ended, and the output from the VCA is single-ended, unless otherwise noted. This results in a 6dB reduction in signal
amplitude compared to differential operation.
GAIN vs FREQUENCY
GAIN vs FREQUENCY
(Pre-Amp)
VCA
(VCACNTL = 0.2V)
30
25
20
15
10
5
5.0
4.0
LNA = 25dB
LNA = 22dB
3.0
2.0
1.0
MGS = 111
MGS = 100
0.0
LNA = 17dB
–1.0
–2.0
–3.0
–4.0
–5.0
MGS = 011
MGS = 000
LNA = 5dB
10M
0
100k
1M
100M
100M
100M
100k
1M
10M
100M
Frequency (Hz)
Frequency (Hz)
GAIN vs FREQUENCY
LNA and VCA
(VCACNTL = 3.0V)
GAIN vs FREQUENCY
VCA
(VCACNTL = 3.0V)
45
40
35
30
25
20
15
10
5
60
50
40
30
20
10
0
LNP = 25dB
LNP = 22dB
MGS = 111
MGS = 100
LNP = 17dB
LNP = 5dB
MGS = 011
MGS = 000
0
100k
1M
10M
100k
1M
10M
100M
Frequency (Hz)
Frequency (Hz)
GAIN vs FREQUENCY
LNA and VCA
OUTPUT-REFERRED NOISE vs VCACNTL
(LNP = 25dB)
(LNP = 22dB)
60
50
40
30
20
10
0
2000
1800
1600
1400
1200
1000
800
RS= 50Ω
VCNTL = 3.0V
VCNTL = 1.6V
MGS = 111
600
400
VCNTL = 0.2V
200
MGS = 011
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
100k
1M
10M
Frequency (Hz)
VCA2616, VCA2611
5
SBOS234E
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDDA = VDDB = VDDR = +5V, load resistance = 500Ω on each output to ground, MGS = 011, LNP = 22dB and fIN = 5MHz, unless otherwise noted.
The input to the preamp (LNP) is single-ended, and the output from the VCA is single-ended unless otherwise noted. This results in a 6dB reduction in signal
amplitude compared to differential operation.
INPUT-REFERRED NOISE vs RS
(LNP = 25dB)
INPUT-REFERRED NOISE vs VCACNTL
(LNP = 25dB)
10.0
24
22
20
18
16
14
12
10
8
RS = 50Ω
MGS = 111
1.0
MGS = 111
6
4
2
MGS = 011
0.1
0
1
10
100
1k
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
RS (Ω)
NOISE FIGURE vs RS
(LNP = 25dB)
NOISE FIGURE vs VCACNTL
(LNP = 25dB)
9
8
7
6
5
4
3
2
1
0
30
28
26
24
22
20
18
16
14
12
10
8
MGS = 111
MGS = 111
6
4
2
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
10
100
1k
RS (Ω)
DISTORTION vs FREQUENCY
MGS = 011
DISTORTION vs FREQUENCY
MGS = 000
2VPP DIFFERENTIAL
2VPP DIFFERENTIAL
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
–90
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
VC = 0.2, H2
VC = 0.2, H3
VC = 0.2, H2
VC = 3.0, H2
VC = 0.2, H3
VC = 3.0, H3
VC = 3.0, H2
VC = 3.0, H3
100k
1M
10M
100k
1M
Frequency (Hz)
10M
Frequency (Hz)
VCA2616, VCA2611
6
SBOS234E
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDDA = VDDB = VDDR = +5V, load resistance = 500Ω on each output to ground, MGS = 011, LNP = 22dB and fIN = 5MHz, unless otherwise noted.
The input to the preamp (LNP) is single-ended, and the output from the VCA is single-ended, unless otherwise noted. This results in a 6dB reduction in signal
amplitude compared to differential operation.
DISTORTION vs FREQUENCY
MGS = 111
DISTORTION vs FREQUENCY
MGS = 000
2VPP DIFFERENTIAL
1VPP SINGLE-ENDED
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
–90
VC = 0.2, H2
VC = 0.2, H3
VC = 0.2, H3
VC = 0.2, H2
VC = 3.0, H2
VC = 3.0, H3
VC = 3.0, H2
VC = 3.0, H3
100k
1M
10M
100k
1M
Frequency (Hz)
10M
Frequency (Hz)
DISTORTION vs FREQUENCY
MGS = 011
DISTORTION vs FREQUENCY
MGS = 111
1VPP SINGLE-ENDED
1VPP SINGLE-ENDED
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
–90
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
–90
VC = 0.2, H3
VC = 0.2, H2
VC = 0.2, H2
VC = 0.2, H3
VC = 3.0, H2
VC = 3.0, H2
VC = 3.0, H3
VC = 3.0, H3
100k
1M
10M
100k
1M
Frequency (Hz)
10M
Frequency (Hz)
DISTORTION vs VCACNTL
1VPP SINGLE-ENDED
DISTORTION vs VCACNTL
2VPP DIFFERENTIAL
–45
–50
–55
–60
–65
–70
–75
–80
–45
–50
–55
–60
–65
–70
–75
–80
MGS = 111, H2
MGS = 111, H2
MGS = 011, H2
MGS = 000, H2
MGS = 011, H2
MGS = 000, H2
MGS = 011, H3
MGS = 000, H3
MGS = 111, H3
MGS = 111, H3
MGS = 011, H3
MGS = 000, H3
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0
VCACNTL (V)
VCA2616, VCA2611
7
SBOS234E
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDDA = VDDB = VDDR = +5V, load resistance = 500Ω on each output to ground, MGS = 011, LNP = 22dB and fIN = 5MHz, unless otherwise noted.
The input to the preamp (LNP) is single-ended, and the output from the VCA is single-ended, unless otherwise noted. This results in a 6dB reduction in signal
amplitude compared to differential operation.
CROSSTALK vs FREQUENCY
1VPP SINGLE-ENDED
ICC vs TEMPERATURE
MGS = 011
80.50
80.00
79.50
79.00
78.50
78.00
77.50
77.00
76.50
76.00
–5
–15
–25
–35
–45
–55
–65
–75
–85
VCACNTRL 0V
VCACNTRL 1.5V
VCACNTRL 3.0V
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90
1M
10M
100M
Frequency (Hz)
Temperature (°C)
GROUP DELAY vs FREQUENCY
VC = 3.0
16
14
12
10
8
VC = 0.2
6
4
2
0
1M
10M
100M
Frequency (Hz)
VCA2616, VCA2611
8
SBOS234E
www.ti.com
op amp. The VCM node shown in Figure 2 is the VCM output
(pin 19). Typical R and C values are shown, yielding a high-
pass time constant similar to that of the LNP. If a different
common-mode referencing method is used, it is important
that the common-mode level be within 10mV of the VCM
output for proper operation.
THEORY OF OPERATION
The VCA2616 and VCA2611 are dual-channel systems con-
sisting of three primary blocks: an LNP, a VCA, and a
Programmable Gain Amplifier (PGA). For greater system
flexibility, an onboard multiplexer is provided for the VCA
inputs, selecting either the LNP outputs or external signal
inputs. Figure 1 shows a simplified block diagram of the dual-
channel system.
1kΩ
External
InA
To VCAIN
47nF
Input
Signal
Channel A
Input
Channel A
Output
LNP
VCA
PGA
1kΩ
VCM (+2.5V)
Maximum
Gain
Analog
Control
VCA
Control
MGS
Select
FIGURE 2. Recommended Circuit for Coupling an External
Signal into the VCA Inputs.
Channel B
Input
Channel B
Output
LNP
VCA
PGA
VCA—OVERVIEW
The magnitude of the differential VCA input signal (from the
LNP or an external source) is reduced by a programmable
attenuation factor, set by the analog VCA Control Voltage
(VCACNTL) at pin 43. The maximum attenuation factor is
further programmable by using the three MGS bits
(pins 40-42). Figure 3 illustrates this dual-adjustable charac-
teristic. Internally, the signal is attenuated by having the
analog VCACNTL vary the channel resistance of a set of
shunt-connected FET transistors. The MGS bits effectively
adjust the overall size of the shunt FET by switching parallel
components in or out under logic control. At any given
maximum gain setting, the analog variable gain characteris-
tic is linear in dB as a function of the control voltage, and is
created as a piecewise approximation of an ideal dB-linear
transfer function. The VCA gain control circuitry is common
to both channels of the VCA2616 and VCA2611.
External
InB
FIGURE 1. Simplified Block Diagram of the VCA2616.
LNP—OVERVIEW
The LNP input may be connected to provide active-feedback
signal termination, achieving lower system noise perfor-
mance than conventional passive shunt termination. Further
lower noise performance is obtained if signal termination is
not required. The unterminated LNP input impedance is
600kΩ. The LNP can process fully differential or single-
ended signals in each channel. Differential signal processing
results in significantly reduced 2nd-harmonic distortion and
improved rejection of common-mode and power-supply noise.
The first gain stage of the LNP is AC-coupled into its output
buffer with a 4.8µs time constant (33kHz high-pass charac-
teristic). The buffered LNP outputs are designed to drive the
succeeding VCA directly or, if desired, external loads as low
as 135Ω with minimal impact on signal distortion. The LNP
employs very low impedance local feedback to achieve
stable gain with the lowest possible noise and distortion.
Four pin-programmable gain settings are available: 5dB,
17dB, 22dB, and 25dB. Additional intermediate gains can be
programmed by adding trim resistors between the Gain Strap
programming pins.
0
Minimum Attenuation
–24
The common-mode DC level at the LNP output is nominally
2.5V, matching the input common-mode requirement of the
VCA for simple direct coupling. When external signals are
fed to the VCA, they should also be set up with a 2.5VDC
common-mode level. Figure 2 shows a circuit that demon-
strates the recommended coupling method using an external
Maximum Attenuation
–45
0
3.0
Control Voltage (V)
FIGURE 3. Swept Attenuator Characteristic.
VCA2616, VCA2611
9
SBOS234E
www.ti.com
PGA OVERVIEW AND OVERALL DEVICE
CHARACTERISTICS
the circuit. This reduces the susceptibility to power-supply
variation, ripple, and noise. In addition, separate power
supply and ground connections are provided for each chan-
nel and for the reference circuitry, further reducing interchannel
crosstalk.
The differential output of the VCA attenuator is then amplified
by the PGA circuit block. This post-amplifier is programmed
by the same MGS bits that control the VCA attenuator,
yielding an overall swept-gain amplifier characteristic in which
the VCA × PGA gain varies from 0dB (unity) to a program-
mable peak gain of 24-, 27-, 30-, 33-, 36-, 39-, 42-, or 45dB.
Further details regarding the design, operation, and use of
each circuit block are provided in the following sections.
The Gain vs VCACNTL curve in the Typical Characteristics
shows the composite gain control characteristic of the entire
VCA2616. Setting VCACNTL to 3.0V causes the digital MGS
gain control to step in 3dB increments. Setting VCACNTL to 0V
causes all the MGS-controlled gain curves to converge at
one point. The gain at the convergence point is the LNP gain
less 6dB, because the measurement setup looks at only one
side of the differential PGA output, resulting in 6dB lower
signal amplitude.
LOW-NOISE PREAMPLIFIER (LNP)—DETAIL
The LNP is designed to achieve a low-noise figure, espe-
cially when employing active termination. Figure 4 is a
simplified schematic of the LNP, illustrating the differential
input and output capability. The input stage employs low
resistance local feedback to achieve stable low-noise, low-
distortion performance with very high input impedance. Nor-
mally, low noise circuits exhibit high power consumption as
a result of the large bias currents required in both input and
output stages. The LNP uses a patented technique that
combines the input and output stages such that they share
the same bias current. Transistors Q4 and Q5 amplify the
signal at the gate-source input of Q4, the +IN side of the LNP.
The signal is further amplified by the Q1 and Q2 stage, and
then by the final Q3 and RL gain stage, which uses the same
bias current as the input devices Q4 and Q5. Devices Q6
through Q10 play the same role for signals on the –IN side.
ADDITIONAL FEATURES—OVERVIEW
Overload protection stages are placed between the attenua-
tor and the PGA, providing a symmetrically clipped output
whenever the input becomes large enough to overload the
PGA. A comparator senses the overload signal amplitude
and substitutes a fixed DC level to prevent undesirable
overload recovery effects. As with the previous stages, the
VCA is AC-coupled into the PGA. In this case, the coupling
time constant varies from 5µs at the highest gain (45dB) to
59µs at the lowest gain (25dB).
The differential gain of the LNP is given in Equation 1:
RL
(1)
Gain = 2 ×
RS
The VCA2616 includes a built-in reference, common to both
channels, to supply a regulated voltage for critical areas of
COMP2A
VDD
COMP1A
RL
RL
To Bias
Circuitry
93Ω
93Ω
Q9
Q2
LNPOUTN LNPOUT
P
Buffer
Buffer
CCOMP
4.7pF
(External
Capacitor)
Q3
Q8
RS1
105Ω
RS2
34Ω
RW
RW
LNPGS1
Q4
Q7
LNPINP
LNPINN
LNPGS2
LNPGS3
RS3
17Ω
Q10
Q1
To Bias
Circuitry
Q5
Q6
FIGURE 4. Schematic of the Low-Noise Preamplifier (LNP).
10
VCA2616, VCA2611
SBOS234E
www.ti.com
where RL is the load resistor in the drains of Q3 and Q8, and
RS is the resistor connected between the sources of the input
transistors Q4 and Q7. The connections for various RS com-
binations are brought out to device pins LNPGS1, LNPGS2,
and LNPGS3 (pins 13-15 for channel A, 22-24 for channel B).
These Gain Strap pins allow the user to establish one of four
fixed LNP gain options as shown in Table I.
NOISE (nV/√Hz)
LNP GAIN (dB)
Input-Referred
Output-Referred
25
22
17
5
1.35
1.41
1.63
4.28
2260
1650
1060
597
TABLE II. Equivalent Noise Performance for MGS = 111 and
VCACNTL = 3.0V with 50Ω source impedance.
LNP PIN STRAPPING
LNP GAIN (dB)
LNPGS1, LNPGS2, LNPGS3 Connected Together
LNPGS1 Connected to LNPGS3
LNPGS1 Connected to LNPGS2
All Pins Open
25
22
17
5
The LNP is capable of generating a 2VPP differential signal.
The maximum signal at the LNP input is therefore 2VPP
divided by the LNP gain. An input signal greater than this
would exceed the linear range of the LNP, an especially
important consideration at low LNP gain settings.
TABLE I. Pin Strappings of the LNP for Various Gains.
The VCA2611 is an upgraded version of the VCA2616. The
only difference between the VCA2616 and the VCA2611 is the
input structure to the LNP. The VCA2616 is limited to –0.3V
negative-going input spikes; the VCA2611 is limited to –2.0V
negative-going input spikes. This change allows the user to
use slower and less expensive input clamping diodes prior to
the LNA input. In some designs, input clamping may not be
required.
It is also possible to create other gain settings by connecting
an external resistor between LNPGS1 on one side, and
LNPGS2 and/or LNPGS3 on the other. In that case, the
internal resistor values (see Figure 4) should be combined
with the external resistor to calculate the effective value of RS
for use in Equation 1. The resulting expression for external
resistor value is given in Equation 2:
2RS1RL + 2RFIXRL – Gain ×RS1RFIX
Gain× RS1 – 2RL
(2)
REXT
=
ACTIVE FEEDBACK WITH THE LNP
One of the key features of the LNP architecture is the ability
to employ active-feedback termination to achieve superior
noise performance. Active-feedback termination achieves a
lower noise figure than conventional shunt termination, es-
sentially because no signal current is wasted in the termina-
tion resistor itself. Another way to understand this is to
consider first that the input source, at the far end of the signal
cable, has a cable-matching source resistance of RS. Using
conventional shunt termination at the LNP input, a second
terminating resistor of value RS is connected to ground.
Therefore, the signal loss is 6dB due to the voltage divider
action of the series and shunt RS resistors. The effective
source resistance has been reduced by the same factor of 2,
where REXT is the externally selected resistor value needed
to achieve the desired gain setting, RS1 is the fixed parallel
resistor in Figure 4, and RFIX is the effective fixed value of the
remaining internal resistors: RS2, RS3, or (RS2 || RS3), de-
pending on the pin connections.
Note that the best process and temperature stability will be
achieved by using the pre-programmed fixed-gain options of
Table I, since the gain is then set entirely by internal resistor
ratios, which are typically accurate to ±0.5%, and track quite
well over process and temperature. When combining exter-
nal resistors with the internal values to create an effective RS
value, note that the internal resistors have a typical tempera-
ture coefficient of +700ppm/°C and an absolute value toler-
ance of approximately ±5%, yielding somewhat less predict-
able and stable gain settings. With or without external resis-
tors, the board layout should use short Gain Strap connec-
tions to minimize parasitic resistance and inductance effects.
but the noise contribution has been reduced by only the √2
,
only a 3dB reduction. Therefore, the net theoretical SNR
degradation is 3dB, assuming a noise-free amplifier input. (In
practice, the amplifier noise contribution will degrade both
the unterminated and the terminated noise figures, some-
what reducing the distinction between them.)
The overall noise performance of the VCA2616 and VCA2611
will vary as a function of gain. Table II shows the typical input-
and-output-referred noise densities of the entire VCA2616 and
VCA2611 for maximum VCA and PGA gain; that is, VCACNTL
set to 3.0V and all MGS bits set to 1. Note that the input-
referred noise values include the contribution of a 50Ω fixed
source impedance, and are therefore somewhat larger than
the intrinsic input noise. As the LNP gain is reduced, the noise
contribution from the VCA/PGA portion becomes more signifi-
cant, resulting in higher input-referred noise. However, the
output-referred noise, which is indicative of the overall SNR at
that gain setting, is reduced.
See Figure 5 for an amplifier using active feedback. This
diagram appears very similar to a traditional inverting ampli-
fier. However, the analysis is somewhat different because
the gain A in this case is not a very large open-loop op amp
gain; rather, it is the relatively low and controlled gain of the
LNP itself. Thus, the impedance at the inverting amplifier
terminal will be reduced by a finite amount, as given in the
familiar relationship of Equation 3:
RF
RIN
=
(3)
1+ A
(
)
where RF is the feedback resistor (supplied externally be-
tween the LNPINP and FB terminals for each channel), A is
To preserve the low-noise performance of the LNP, the user
should take care to minimize resistance in the input lead. A
parasitic resistance of only 10Ω will contribute 0.4nV/√Hz
.
VCA2616, VCA2611
11
SBOS234E
www.ti.com
RF
VCA NOISE = 3.8nV√Hz, LNP GAIN = 20dB
LNP Noise
14
12
10
8
nV/√Hz
6.0E-10
8.0E-10
1.0E-09
1.2E-09
1.4E-09
1.6E-09
1.8E-09
2.0E-09
RS
LNPIN
A
RIN
RIN
6
Active Feedback
RF
4
=
= RS
1 + A
2
RS
0
0
100 200 300 400 500 600 700 800 900 1000
A
Source Impedance (Ω)
RS
FIGURE 7. Noise Figure for Conventional Termination.
noise figure for active and conventional termination methods.
The left-most set of data points in each graph give the results
for typical 50Ω cable termination, showing the worst noise
figure but also the greatest advantage of the active feedback
method.
Conventional Cable Termination
FIGURE 5. Configurations for Active Feedback and Conven-
tional Cable Termination.
A switch, controlled by the FBSWCNTL signal on pin 45,
enables the user to reduce the feedback resistance by
adding an additional parallel component, connected between
the LNPINP and SWFB terminals. The two different values of
feedback resistance will result in two different values of
active-feedback input resistance. Thus, the active-feedback
impedance can be optimized at two different LNP gain
settings. The switch is connected at the buffered output of
the LNP and has an ON resistance of approximately 1Ω.
the user-selected gain of the LNP, and RIN is the resulting
amplifier input impedance with active feedback. In this case,
unlike the conventional termination above, both the signal
voltage and the RS noise are attenuated by the same factor
of 2 (6dB) before being re-amplified by the A gain setting.
This avoids the extra 3dB degradation due to the square-root
effect described earlier, the key advantage of the active
termination technique.
This previous explanation ignored the input noise contribu-
tion of the LNP itself. Also, the noise contribution of the
feedback resistor must be included for a completely correct
analysis. The curves given in Figures 6 and 7 allow the
VCA2616 and VCA2611 user to compare the achievable
When employing active feedback, the user should be careful
to avoid low-frequency instability or overload problems. Fig-
ure 8 illustrates the various low-frequency time constants.
RF
VCA NOISE = 3.8nV√Hz, LNP GAIN = 20dB
9
VCM
LNP Noise
nV/√Hz
8
CF
0.001µF
200kΩ
7
6
5
4
3
2
1
0
6.0E-10
8.0E-10
1.0E-09
1.2E-09
1.4E-09
1.6E-09
1.8E-09
2.0E-09
44pF
44pF
CC
Buffer
Buffer
LNPOUT
N
RS
LNPOUTP
Gain
200kΩ
Stage
VCM
0
100 200 300 400 500 600 700 800 900 1000
(VCA) LNP
Source Impedance (Ω)
FIGURE 6. Noise Figure for Active Termination.
FIGURE 8. Low-Frequency LNP Time Constants.
VCA2616, VCA2611
12
SBOS234E
www.ti.com
Referring again to the input resistance calculation of Equa-
tion (3), and considering that the gain term “A” falls off below
21kHz, it is evident that the effective LNP input impedance
will rise below 3.6kHz, with a DC limit of approximately RF. To
avoid interaction with the feedback pole/zero at low frequen-
cies, and to avoid the higher signal levels resulting from the
rising impedance characteristic, it is recommended that the
external RFCC time constant be set to about 5µs.
RF
RI
Input
C
A
Output
FIGURE 10. LNP with Compensation Capacitor.
Achieving the best active-feedback architecture is difficult
with conventional op amp circuit structures. The overall gain
A must be negative in order to close the feedback loop, the
input impedance must be high to maintain low current noise
and good gain accuracy, but the gain ratio must be set with
very low value resistors to maintain good voltage noise.
Using a two-amplifier configuration (noninverting for high
impedance plus inverting for negative feedback reasons)
results in excessive phase lag and stability problems when
the loop is closed. The VCA2616 and VCA2611 use a
patented architecture that achieves these requirements, with
the additional benefits of low power dissipation and differen-
tial signal handling at both input and output.
AVOIDING UNSTABLE PERFORMANCE
The VCA2612 and the VCA2616 are very similar in perfor-
mance in all respects, except in the area of noise performance.
See Figure 4 for a schematic of the LNP. This brings the input
noise of the VCA2616 and VCA2611 down to 1.0nV/√Hz
compared to the input on the VCA2612 1.25nV/√Hz imped-
ance at the gate of either Q4 or Q7, as can be approximated
by the network shown in Figure 11. The resistive component
shown in Figure 11 is negative, which gives rise to unstable
behavior when the signal source resistance has both inductive
and capacitive elements. It should be noted that this negative
resistance is not a physical resistor, but an equivalent resis-
tance that is a function of the devices shown in Figure 4.
Normally, when an inductor and capacitor are placed in series
or parallel, there is a positive resistance in the loop that
prevents unstable behavior.
For greatest flexibility and lowest noise, the user may wish to
shape the frequency response of the LNP. The COMP1 and
COMP2 pins for each channel (pins 10 and 11 for channel A,
pins 26 and 27 for channel B) correspond to the drains of Q3
and Q8, see Figure 4. A capacitor placed between these pins
will create a single-pole low-pass response, in which the
effective R of the RC time constant is approximately 186Ω.
COMPENSATIONWHENUSINGACTIVEFEEDBACK
24pF
The typical open-loop gain versus frequency characteristic for
the LNP is shown in Figure 9. The –3dB bandwidth is approxi-
mately 180MHz and the phase response is such that when
feedback is applied, the LNP will exhibit a peaked response or
might even oscillate. One method of compensating for this
undesirable behavior is to place a compensation capacitor at
the input to the LNP, as shown in Figure 10. This method is
effective when the desired –3dB bandwidth is much less than
the open-loop bandwidth of the LNP. This compensation
technique also allows the total compensation capacitor to
include any stray or cable capacitance that is associated with
the input connection. Equation 4 relates the bandwidth to the
various impedances that are connected to the LNP.
–93Ω
57pF
FIGURE 11. VCA2616 and VCA2611 Input Impedance.
For the VCA2616 and VCA2611, the situation can be rem-
edied by placing an external resistor with a value of approxi-
mately 15Ω or higher in series with the input lead. The net
series resistance will be positive, and there will be no
observed instability.
A + 1 R + R
(
)
I
F
BW =
(4)
Although this technique will prevent oscillations, it is not
recommended, as it will also increase the input noise. A
4.7pF external capacitor must be placed between pins
COMP2A (pin 11) and LNPINPA (pin 16), and between pins
COMP2B (pin 26) and LNPINPB (pin 21). This has the result
of making the input impedance always capacitive due to the
feedback effect of the compensation capacitor and the gain
of the LNP. Using capacitive feedback, the LNP becomes
unconditionally stable, as there is no longer a negative
component to the input impedance. The compensation
capacitor mentioned above will be reflected to the input by
the formula:
2πC(RI )(RF )
–3dB Bandwidth
25dB
180MHz
CIN = (A + 1)CCOMP
(5)
FIGURE 9. Open-Loop Gain Characteristic of LNP.
VCA2616, VCA2611
13
SBOS234E
www.ti.com
The capacitance that is determined in Equation 5 should be
added to the capacitance of Equation 4 to determine the
overall bandwidth of the LNP. The LNPINNA (pin 12) and the
LNPINNB (pin 25) should be bypassed to ground by the
shortest means possible to avoid any inductance in the lead.
The attenuator is comprised of two sections, with five parallel
clipping amplifier/FET combinations in each. Special refer-
ence circuitry is provided so that the (VCM – VT) limit voltage
will track temperature and IC process variations, minimizing
the effects on the attenuator control characteristic.
In addition to the analog VCACNTL gain setting input, the
attenuator architecture provides digitally programmable ad-
justment in eight steps, via the three MGS bits. These adjust
the maximum achievable gain (corresponding to minimum
attenuation in the VCA, with VCACNTL = 3.0V) in 3dB incre-
ments. This function is accomplished by providing multiple
FET sub-elements for each of the Q1 to Q10 FET shunt
elements (see Figure 12). In the simplified diagram of
Figure 13, each shunt FET is shown as two sub-elements,
QNA and QNB. Selector switches, driven by the MGS bits,
activate either or both of the sub-element FETs to adjust the
maximum RON and thus achieve the stepped attenuation
options.
LNP OUTPUT BUFFER
The differential LNP output is buffered by wideband class AB
voltage followers which are designed to drive low impedance
loads. This is necessary to maintain LNP gain accuracy,
since the VCA input exhibits gain-dependent input imped-
ance. The buffers are also useful when the LNP output is
brought out to drive external filters or other signal processing
circuitry. Good distortion performance is maintained with
buffer loads as low as 135Ω. As mentioned previously, the
buffer inputs are AC-coupled to the LNP outputs with a
3.6kHz high-pass characteristic, and the DC common-mode
level is maintained at the correct VCM for compatibility with
the VCA input.
The VCA can be used to process either differential or single-
ended signals. Fully differential operation will reduce 2nd-
harmonic distortion by about 10dB for full-scale signals.
VOLTAGE-CONTROLLED ATTENUATOR (VCA)—DETAIL
Input impedance of the VCA will vary with gain setting, due
to the changing resistances of the programmable voltage
divider structure. At large attenuation factors (that is, low gain
settings), the impedance will approach the series resistor
value of approximately 135Ω.
The VCA is designed to have a dB-linear attenuation charac-
teristic; that is, the gain loss in dB is constant for each equal
increment of the VCACNTL control voltage. See Figure 1 for a
block diagram of the VCA. The attenuator is essentially a
variable voltage divider consisting of one series input resis-
tor, RS, and ten identical shunt FETs, placed in parallel and
controlled by sequentially activated clipping amplifiers. Each
clipping amplifier can be thought of as a specialized voltage
comparator with a soft transfer characteristic and well-con-
trolled output limit voltages. The reference voltages V1 through
V10 are equally spaced over the 0V to 3.0V control voltage
range. As the control voltage rises through the input range of
each clipping amplifier, the amplifier output will rise from 0V
(FET completely ON) to VCM – VT (FET nearly OFF), where
VCM is the common source voltage and VT is the threshold
voltage of the FET. As each FET approaches its OFF state
and the control voltage continues to rise, the next clipping
amplifier/FET combination takes over for the next portion of
the piecewise-linear attenuation characteristic. Thus, low
control voltages have most of the FETs turned ON, while
high control voltages have most turned OFF. Each FET acts
to decrease the shunt resistance of the voltage divider
formed by RS and the parallel FET network.
As with the LNP stage, the VCA output is AC-coupled into the
PGA. This means that the attenuation-dependent DC com-
mon-mode voltage will not propagate into the PGA, and so
the PGA’s DC output level will remain constant.
Finally, note that the VCACNTL input consists of FET gate
inputs. This provides very high impedance and ensures that
multiple VCA2616 and VCA2611 devices may be connected
in parallel with no significant loading effects. The nominal
voltage range for the VCACNTL input spans from 0V to 3V.
Overdriving this input (≤ 5V) does not affect the performance.
INPUT OVERLOAD RECOVERY
One of the most important applications for the VCA2616 and
VCA2611 is processing signals in an ultrasound system. The
ultrasound signal flow begins when a large signal is applied to
a transducer, which converts electrical energy to acoustic
energy. It is not uncommon for the amplitude of the electrical
signal that is applied to the transducer to be ±50V or greater.
RS
OUTPUT
INPUT
Q1A
Q1B
Q2A
Q2B
Q3A
Q3B
Q4A
Q4B
Q5A
Q5B
VCM
A1
A2
A3
A4
A5
B1
B2
Programmable Attenuator Section
FIGURE 13. Programmable Attenuator Section.
14
VCA2616, VCA2611
SBOS234E
www.ti.com
Attenuator
Input
A1-A10 Attenuator Stages
QS
Attenuator
Output
RS
Q1
A2
Q2
A3
Q3
A4
Q4
A5
Q5
Q6
A7
Q7
A8
Q8
A9
Q9
A10
Q10
VCM
A1
A6
C1
V1
C2
V2
C3
V3
C4
V4
C5
V5
C6
V6
C7
V7
C8
V8
C9
V9
C10
V10
Control
Input
C1-C10 Clipping Amplifiers
0dB
–4.5dB
Attenuation Characteristic of Individual FETs
VCM-VT
0
V1
V2
V3
V4
V5
V6
V7
V8
V9
V10
Characteristic of Attenuator Control Stage Output
Overall Control Characteristics of Attenuator
0dB
–45dB
0.3V
3V
Control Signal
FIGURE 12. Piecewise Approximation to Logarithmic Control Characteristics.
VCA2616, VCA2611
15
SBOS234E
www.ti.com
(= maximum attenuation). For VCACNTL = 3V (no attenuation),
the VCA + PGA gain will be controlled by the programmed
PGA gain (24 to 45 dB in 3dB steps). For clarity, the gain and
attenuation factors are detailed in Table III.
VDD
CF
RF
MGS
ATTENUATOR GAIN DIFFERENTIAL ATTENUATOR +
SETTING VCACNTL = 0V to 3V
PGA GAIN
DIFF. PGA GAIN
LNPOUTN
000
001
010
011
100
101
110
111
–24dB to 0dB
–27dB to 0dB
–30dB to 0dB
–33dB to 0dB
–36dB to 0dB
–39dB to 0dB
–42dB to 0dB
–45dB to 0dB
24dB
27dB
30dB
33dB
36dB
39dB
42dB
45dB
0dB to 24dB
0dB to 27dB
0dB to 30dB
0dB to 33dB
0dB to 36dB
0dB to 39dB
0dB to 42dB
0dB to 45dB
LNPIN
P
Protection
Network
LNP
ESD Diode
FIGURE 14. VCA2616 and VCA2611 Diode Bridge Protection
Circuit.
TABLE III. MGS Settings.
To prevent damage, it is necessary to place a protection circuit
between the transducer and the VCA2616 and VCA2611 (see
Figure 14). Care must be taken to prevent any signal from
turning the ESD diodes on. Turning on the ESD diodes inside
the VCA2616 and VCA2611 could cause the input coupling
capacitor (CC) to charge to the wrong value.
The PGA architecture consists of a differential, program-
mable-gain voltage to current converter stage followed by
transimpedance amplifiers to create and buffer each side of
the differential output. The circuitry associated with the volt-
age to current converter is similar to that previously de-
scribed for the LNP, with the addition of eight selectable PGA
gain-setting resistor combinations (controlled by the MGS
bits) in place of the fixed resistor network used in the LNP.
Low input noise is also a requirement of the PGA design due
to the large amount of signal attenuation which can be
inserted between the LNP and the PGA. At minimum VCA
attenuation (used for small input signals) the LNP noise
dominates; at maximum VCA attenuation (large input sig-
nals) the PGA noise dominates. Note that if the PGA output
is used single-ended, the apparent gain will be 6dB lower.
PGA POST-AMPLIFIER—DETAIL
Figure 15 shows a simplified circuit diagram of the PGA block.
As described previously, the PGA gain is programmed with
the same MGS bits which control the VCA maximum attenu-
ation factor. Specifically, the PGA gain at each MGS setting is
the inverse (reciprocal) of the maximum VCA attenuation at
that setting. Therefore, the VCA + PGA overall gain will always
be 0dB (unity) when the analog VCACNTL input is set to 0V
VDD
To Bias
Circuitry
Q1
Q11
Q12
Q9
RL
RL
VCAOUT
P
VCAOUTN
Q3
Q8
VCM
VCM
RS1
RS2
Q13
Q4
Q7
+In
–In
Q14
Q2
Q10
Q5
Q6
To Bias
Circuitry
FIGURE 15. Simplified Block Diagram of the PGA Section Within the VCA2616 and VCA2611.
VCA2616, VCA2611
16
SBOS234E
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
VCA2611Y/250
ACTIVE
TQFP
PFB
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
VCA2611Y
VCA2611Y/2K
VCA2616YR
ACTIVE
ACTIVE
TQFP
TQFP
PFB
PFB
48
48
TBD
Call TI
Call TI
-40 to 85
VCA2611Y
VCA2616Y
2000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
VCA2616YT
ACTIVE
TQFP
PFB
48
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
VCA2616Y
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
VCA2611Y/250
VCA2616YT
TQFP
TQFP
PFB
PFB
48
48
250
250
177.8
177.8
16.4
16.4
9.6
9.6
9.6
9.6
1.5
1.5
12.0
12.0
16.0
16.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
VCA2611Y/250
VCA2616YT
TQFP
TQFP
PFB
PFB
48
48
250
250
210.0
210.0
185.0
185.0
35.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
MTQF019A – JANUARY 1995 – REVISED JANUARY 1998
PFB (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
M
0,08
36
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
Gage Plane
6,80
9,20
SQ
8,80
0,25
0,05 MIN
0°–7°
1,05
0,95
0,75
0,45
Seating Plane
0,08
1,20 MAX
4073176/B 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明