EV1412-0600-A [TDK]

µPOL™嵌入式DC-DC转换器;
EV1412-0600-A
型号: EV1412-0600-A
厂家: TDK ELECTRONICS    TDK ELECTRONICS
描述:

µPOL™嵌入式DC-DC转换器

DC-DC转换器
文件: 总14页 (文件大小:2280K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
EV1412-0600-A  
EV1412-0600-A  
EVALUATION BOARD  
USER GUIDE  
Page 1  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Introduction  
This user guide describes the evaluation board provided for the FS1412 µPOLproduct.  
The board generates an output voltage (VOUT) of 1V for loads of 012A from an input voltage (PVIN) of 12V.  
Specifications  
Input voltage (PVIN) = +12V  
Output voltage (VOUT) = +1V  
Output load (IO) = 012A  
Switching frequency (FSW) = 1.0MHz  
Output capacitance (CO) = 4x47µF (MLCC)  
Input capacitance (CIN) = 3x22µF (MLCC)  
Dimensions (width x length x thickness) = 61mm x 89mm x 1.6mm  
Connections  
Name  
Identifier  
J1  
Description  
Input voltage (+12V)  
PVIN  
PGnd  
VOUT  
J4  
J3  
Ground for input voltage  
Output voltage (+1V)  
PGnd  
VIN  
J2  
VIN  
Ground for output voltage  
LDO input voltage  
VCC  
PGnd  
En  
PGood  
VCC  
Internal supply (VCC) output of an LDO regulator  
Power ground  
Enable  
Power Good  
I2C/PMBUS clock line  
PGnd  
TP11  
PGood  
J5  
SCL  
SDA  
J5  
I2C/PMBUS data line  
SALERT  
SYNC  
SALERT  
J6  
SMBALERT#  
External sync signal  
Load  
J7  
J8  
J9  
Used to connect load: 20-pin Intel Mini Slammer connector  
Used to select output voltage before power up  
Used for measurement: 50ultra-miniature coaxial connector  
Output voltage selector  
Output transient ripple voltage  
The board is configured for a single input supply. An internal low drop-out regulator generates the internal  
supply (VCC) from VIN. The Enable (En) input is connected to PVIN through a resistor divider, so that no external  
Enable signal is needed.  
Operation  
To use the evaluation board:  
1. Connect a well-regulated +12V input supply to PVIN (J1) and Gnd (J4).  
2. Connect a load of 012A to VOUT (J3) and Gnd (J2).  
Page 2  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Description  
The evaluation board consists of a 4-layer PCB made from FR4 glass-reinforced epoxy laminate material. All  
layers use 2oz copper (equating to a thickness of 0.0694mm). The major power components, including the  
FS1412, are mounted on the top side of the board.  
Figure 1 View of board (top)  
Figure 2 View of board (bottom)  
Page 3  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Figure 3 to Figure 6 show the layout of the board layers and Figure 7 shows a schematic of the electrical circuit.  
Figure 3 Board layout layer 1  
Figure 4 Board layout layer 2  
Page 4  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1412-0600-A  
Figure 5 Board layout layer 3  
Figure 6 Board layout layer 4  
Page 5  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Figure 7 Schematic  
Page 6  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Part reference  
C1  
C10,C11,C12  
Quantity Value  
Description  
Manufacturer  
Part number  
1
3
1µF  
0603, 25V, X5R  
0805, 25V, X5R  
0805, 6.3V, X5R  
0402, 10V, X7S  
25V, tantalum  
0402, 25V, X7R  
0603, COG, 50V  
22µF  
47µF  
2.2µF  
68µF  
0.1µF  
220pF  
C14,C15,C17,C19 4  
C2,C3  
C20  
C21  
C4  
2
1
1
1
1
2
1
1
1
1
1
J1  
J2,J4  
J3  
108-0902-001 PVIN banana connector, red  
108-0903-001 Gnd banana connector, black  
108-0904-001 VOUT banana connector, green  
68000-103HLF 3 pin header, 0.1" pitch  
68000-102HLF 2 pin header, 0.1" pitch  
Johnson (Cinch  
Connectivity  
Solutions)  
108-0902-001  
108-0903-001  
108-0904-001  
68000-103HLF  
68000-102HLF  
Q6UJ9A00MS25  
M20-9760442  
J5  
Amphenol  
J6  
J7  
J8  
Not inserted  
Mini Slammer connector, 20-pin Intel  
M20-9760442 Through-board connector, 8-pin, Harwin  
two-row, 0.1" pitch  
J9  
1
U.FL-R-SMT(10) 50ultra-miniature coaxial  
Hirose Electric  
U.FL-R-SMT(10)  
connector  
R1  
R12  
1
1
1
3
1
1
1
2
3
1
1
1
10  
2.7Ω  
0805  
4.12kΩ  
5.90kΩ  
4.99kΩ  
10kΩ  
1.91kΩ  
49.9Ω  
49.9kΩ  
0
0805, 1%  
0805, 1%  
0402  
R13  
R14,R15,R16  
R17  
0805, 1%  
0805, 1%  
0402, 1%  
0805  
R18  
R20  
R3,R7  
R4,R9,R11  
R5  
0805  
100Ω  
0805  
0805  
R6  
12.7kΩ  
FS1412  
5018  
U1  
Main IC  
Test points  
TDK  
VIN, EN, PGND,  
VCC, PVIN,  
Keystone  
5018  
PGND, VOUT,  
PGND, SALERT,  
PGOOD  
Page 7  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Typical performance  
Figure 8 to Figure 18 show typical operating waveforms for the evaluation board, while Figure 19 shows a  
thermal image of the board in operation. In all cases, the board is operating at room temperature with no  
airflow; PVIN is 12V, VOUT is 1V and IO is 012A.  
Figure 8 Startup with no load (Ch2:PVIN, Ch5:VCC, Ch6: VOUT, Ch7: PGood, Ch8: Enable)  
Figure 9 Startup with 12A load (Ch2:PVIN, Ch5:VCC, Ch6: VOUT, Ch7: PGood, Ch8: Enable)  
Page 8  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1412-0600-A  
Figure 10 Shutdown with Enable de-assertion at 12A load  
(Ch2:PVIN, Ch5:VCC, Ch6: VOUT, Ch7: PGood, Ch8: Enable)  
Figure 11 Soft turn off at no load (Ch2:PVIN, Ch5:VCC, Ch6: VOUT, Ch7: PGood, Ch8: Enable)  
Page 9  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Figure 12 Switch node waveforms at no load  
Figure 13 Switch node waveforms at 12A  
Page 10  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Figure 14 VO ripple at 12A (Ch1:IO, Ch8: VOUT), peak-peak VO ripple = 4.6mV  
Figure 15 Transient response 0A to 6A (Ch6: VOUT, Ch8:IO), peak-peak deviation = 53mV, load slew rate = 40A/µs  
Page 11  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Figure 16 Efficiency  
Figure 17 Power loss  
Page 12  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Figure 18 Load regulation (IO = 012A)  
Figure 19 Thermal image at PVIN = 12V, VOUT = 1.0V, IO = 12A,  
room temperature, no airflow, FS1412 maximum temperature rise = 55.5°C  
Page 13  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1412-0600-A  
Disclaimer  
IMPORTANT NOTICE AND DISCLAIMER  
TDK PROVIDES THIS POWER DESIGN USER GUIDE (“Resources”) “AS IS” AND WITH ALL  
FAULTS, AND DISCLAIMS. ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT  
LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR  
PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.  
These Resources are intended for skilled developers designing with TDK products. You are solely responsible for (1) selecting the appropriate TDK  
products for your application, (2) designing, validating and testing your application, (3) ensuring your application meets applicable standards, and any  
other safety, security, or other requirements, and (4) ensuring your application complies with all applicable laws and regulations. These Resources are  
subject to change without notice and TDK assumes no responsibility for any notices or lack thereof. TDK grants you permission to use these Resources  
solely for development of an application that uses the TDK products described in the Resource.  
This permission may be revoked at any time by TDK or any of its affiliates. Your use of these Resources shall be in compliance with all applicable laws  
and regulations including applicable export/import controls. Reproduction and display of these Resources is prohibited. No license is granted to any  
other TDK intellectual property right or to any third party intellectual property right. TDK disclaims responsibility for, and you agree to fully indemnify  
TDK, its affiliates and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these Resources.  
REMINDERS FOR USING THESE PRODUCTS  
Before using these products, be sure to request the delivery specifications.  
SAFETY REMINDERS  
Please pay sufficient attention to the warnings for safe designing when using these products.  
The products listed on this specification sheet are intended for use in general electric equipment (AV equipment, telecommunication equipment,  
home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots)  
under a normal condition and use condition.  
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a  
more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to sociality, person or property.  
Please understand that we are not responsible for any damage or liability caused by use of the products in any of the applications below or for any  
other use exceeding the range or conditions set forth in this specification sheet.  
1.  
2.  
3.  
Aerospace/Aviation equipment  
Transportation equipment (cars, electric trains, ships, etc.)  
Medical equipment  
4.  
5.  
6.  
Power-generation control equipment  
Atomic energy related equipment  
Seabed equipment  
7.  
8.  
9.  
Transportation control equipment  
Public Information-processing equipment  
Military equipment  
10.  
11.  
12.  
13.  
Electric heating apparatus, burning equipment  
Disaster prevention/crime prevention equipment  
Safety equipment  
Other applications that are not considered general-purpose applications  
When using this product in general-purpose application, you are kindly requested to take into consideration securing protection circuit/ equipment or  
providing backup circuits, etc., to ensure higher safety.  
This product is subject to a license from Power One, Inc. related to digital power technology patents owned by Power One,  
Inc. Power One, Inc. technology is protected by patents including:  
AU  
CN  
3287379M 3287437AA 3290643AA 3291357AA  
10371856C 10452610C 10458656C 10459360C 10465848C 1069332A 11124619A 11346682A 1685299A 1685459A  
1685582A 1685583A 1698023A 1802619A  
EP  
1561156A1 1561268A2 1576710A1 1576711A1 1604254A4 1604264A4 1714369A2 1745536A4 1769382A4 1899789A2  
1984801A2  
US  
20040246754 2004090219A1 2004093533A1 2004123164A1 2004123167A1 2004178780A1 2004179382A1  
20050200344 20050223252 2005209373A1 20060061214 2006015619A1 20060174145 20070226526 20070234095  
20070240000 20080052551 20080072080 20080186006 6741099 6788036 6936999 6949916 7000125 7049798  
7069021 7080265 7249267 7266709 7315156 7372682 7373527 7394445 7456617 7459892 7493504 7526660  
04044718A1 04045042A3 04045042C1 04062061A1 04062062A1 04070780A3 04084390A3 04084391A3 05079227A3  
05081771A3 06019569A3 2007001584A3 2007094935A3  
WO  
Page 14  
Rev 1.0, Jan 4, 2022  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright © 202122 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  

相关型号:

EV14D1100K

Metal Oxide Varistors
WPI

EV14D11K

Metal Oxide Varistors
WPI

EV14D11K-J

Metal Oxide Varistors
WPI

EV14D120K

Metal Oxide Varistors
WPI

EV14D120K-H

Metal Oxide Varistors
WPI

EV14D120K-J

Metal Oxide Varistors
WPI

EV14D130K

Metal Oxide Varistors
WPI

EV14D130K-H

Metal Oxide Varistors
WPI

EV14D130K-J

Metal Oxide Varistors
WPI

EV14D140K

Metal Oxide Varistors
WPI

EV14D140K-H

Metal Oxide Varistors
WPI

EV14D140K-J

Metal Oxide Varistors
WPI