MLP1005 [TDK]
Inductors for Power Circuits Multilayer Ferrite;
| 型号： | MLP1005 |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | Inductors for Power Circuits Multilayer Ferrite |
| 文件： | 总9页 (文件大小：108K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
I
N
D
U
C
T
O
R
S
January 2015
Inductors for Power Circuits
Multilayer Ferrite
MLP Series
MLP1005 Type
MLP1005
1005 [0402 inch]*
* Dimensions Code JIS[EIA]
(2/9)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20150109 / inductor_commercial_power_mlp1005_en.
(3/9)
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive
Halogen-free
Inductors for Power Circuits
Multilayer Ferrite
Compatible with lead-free solders
Overview of MLP1005 Type
FEATURES
A low-loss magnetic material is used so that a low-loss inductor for the power supply circuit can be achieved.
Product supporting high frequency applications, suitable for high-speed drive power circuits.
APPLICATION
Smart phones, tablet terminals, digital cameras, video cameras, HDDs, power supply modules, etc.
PART NUMBER CONSTRUCTION
MLP
1005
M
1R0
D
T
0S1
L×W Dimensions
(mm)
Inductance
(μH)
Height
(mm max.)
Series name
Characteristic type
Packaging style
Internal code
1005
1.0×0.5
M
High frequency
1R0
1.0
D
0.75
T
Taping
0S1
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating Storage
Type
ꢀ
ꢀꢀ
temperature
temperature
(pieces/reel)
（°C）
（°C）
（mg）
MLP1005
t=0.75
–40 to +125
–40 to +85
8,000
1.8
ꢀꢁ
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
ꢀꢀꢁ
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
(4/9)
I
N
D
U
C
T
O
R
S
MLP1005 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30 to 60s
Time
t3
10s max.
T2
180°C
150°C
230°C
250 to 260°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
(5/9)
I
N
D
U
C
T
O
R
S
MLP1005 Type
SHAPE & DIMENSIONS
0.30 0.20
0.1min.
1.0 0.05
Dimensions in mm
RECOMMENDED LAND PATTERN
Dimensions in mm
0.5
0.4
0.5
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
(6/9)
I
N
D
U
C
T
O
R
S
MLP1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
Type
Thickness
L
Measuring
frequency
DC resistance
Part No.
T
(mm)max.
(μH)
tolerance
(MHz)
(ꢂ) 30%
(mA)max.
High frequency
0.75
1.0
20%
10
0.53
500
MLP1005M1R0DT0S1
ꢀꢁ Rated current: Current assumed when temperature has risen to 40°C max.
○ Measurement equipment
Measurement item Product No.
Manufacturer
L
4294A+16034G
Type-7561
Agilent Technologies
Yokogawa
DC resistance
＊ Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
(7/9)
I
N
D
U
C
T
O
R
S
(M characteristic product, T dimension of the product 0.75mm max.)
MLP1005Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
2.0
1.8
1.6
1.4
1.2
1.0
1.0μH
0.8
0.6
0.4
0.2
0.0
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
＊ Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
(8/9)
I
N
D
U
C
T
O
R
S
(M characteristic product, T dimension of the product 0.75mm max.)
MLP1005 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
2.0
1.8
1.6
1.4
1.2
1.0
1.0μH
0.8
0.6
0.4
0.2
0.0
0
200
400
600
800
1000
(
)
DC current mA
○ Measurement equipment
Product No.
Manufacturer
4285A+42841A+42842C+42851-61100
Agilent Technologies
＊ Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
(9/9)
I
N
D
U
C
T
O
R
S
MLP1005 Type
PACKAGING STYLE
REEL DIMENSIONS
1.0
+2.0
8.4
–0.0
2.0 0.5
ø13 0.2
ø21 0.8
14.4max.
ø180 2.0
Dimensions in mm
TAPE DIMENSIONS
+0.1
1.5
Sprocket hole
Cavity
–0.0
Type
A
B
K
MLP1005
1.15 0.1
0.65 0.1
1.0 max.
K
B
4.0 0.1
2.0 0.05
2.0 0.05
200min.
160min.
Taping
300min.
Drawing direction
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20150109 / inductor_commercial_power_mlp1005_en.
相关型号：
MLP102M200EB0E
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 1000uF, Through Hole Mount, RADIAL LEADED
CDE
MLP102M200EB1A
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 1000uF, Through Hole Mount, RADIAL LEADED
CDE
MLP102M200EB1C
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 1000uF, Through Hole Mount, RADIAL LEADED
CDE
©2020 ICPDF网 联系我们和版权申明