MLP2520H3R3MT0S1 [TDK]
General Purpose Inductor, 3.3uH, 20%, Ferrite-Core, 1008,;型号: | MLP2520H3R3MT0S1 |
厂家: | TDK ELECTRONICS |
描述: | General Purpose Inductor, 3.3uH, 20%, Ferrite-Core, 1008, 电感器 |
文件: | 总53页 (文件大小:333K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
I
N
D
U
C
T
O
R
S
April 2014
Inductors for Power Circuits
Multilayer Ferrite
MLPseries
MLP1005
MLP1608
MLP2012
MLP2016
MLP2520
1005 [0402 inch]*
1608 [0603 inch]
2012 [0805 inch]
2016 [0806 inch]
2520 [1008 inch]
* Dimensions Code JIS[EIA]
(2/53)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(3/53)
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive
Halogen-free
Inductors for Power Circuits
Multilayer Ferrite
Compatible with lead-free solders
Overview of the MLP Series
FEATURES
A low-loss magnetic material is used so that a low-loss inductor for the power supply circuit can be achieved.
In addition to the inductance value, product types with various features are available so that they can be compatible with different
usages.
K Type: Products with low DC resistance and large current.
H Type: This product uses a low-loss material and has low DC resistance.
* Optimal for when heavy load power efficiency is important.
V Type: As with the H type, this product with a low-loss magnetic material and that has good DC superimposition type characteristics.
* Optimal for when light load power efficiency is important.
S Type: STD product lineup that includes a wide L value and various sizes.
M Type: Product supporting high frequency applications, suitable for high-speed drive power circuits.
APPLICATION
Smart phones, tablet terminals, digital cameras, video cameras, HDDs, power supply modules, etc.
PART NUMBER CONSTRUCTION
MLP
1608
V
R47
B
T
0S1
L×W Dimensions
(mm)
Inductance
(μH)
Height
(mm max.)
Series name
Characteristic type
Packaging style
Internal code
Large current, low
1005
1.0×0.5
K
1R0
1.0
T
0.55
T
Taping
0S1
resistance
Low core loss
(Emphasized DC
resistance)
1608
2012
2016
1.6×0.8
2.0×1.25
2.0×1.6
100
10
1.2
2.5
D
B
0.75
0.95
1.0
H
V
S1R0S
S2R2S
Low core loss
(Emphasized DC
bias characteristics)
M
S
1.2
S
STD product
M
High frequency
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating
temperature
(°C)
Storage
temperature
(°C)
Type
ꢀ
ꢀꢀ
(pieces/reel)
(mg)
1.8
4
5.5
7
10
12
15
25
MLP1005
t=0.75
t=0.75
t=0.95
t=0.55
t=1.0
–40 to +125
–40 to +85
8,000
MLP1608
–40 to +125
–40 to +85
4,000
MLP2012
MLP2016
MLP2520
–40 to +125
–40 to +125
–40 to +125
–40 to +85
–40 to +85
–40 to +85
4,000
3,000
3,000
t=1.0
t=1.2
ꢀꢁ
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
ꢀꢀꢁ
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(4/53)
I
N
D
U
C
T
O
R
S
Overview of the MLP Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30 to 60s
Time
t3
10s max.
T2
180°C
150°C
230°C
250 to 260°C
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(5/53)
I
N
D
U
C
T
O
R
S
MLPseries
MLP1005 Type
SHAPE & DIMENSIONS
0.30 0.20
0.1min.
1.0 0.05
Dimensions in mm
RECOMMENDED LAND PATTERN
Dimensions in mm
0.5
0.4
0.5
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(6/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
MLP1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
(mA)
max.
Thickness T
L
Measuring
frequency
(MHz)
DC resistance
(ꢂ) 30%
Type
High frequency
(mm)
max.
0.75
Part No.
(μH)
1.0
tolerance
20%
10
0.53
500
MLP1005M1R0DT0S1
ꢀꢁ Rated current: Current assumed when temperature has risen to 40°C max.
○ Measurement equipment
Measurement item Product No.
Manufacturer
L
4294A+16034G
Type-7561
Agilent Technologies
Yokogawa
DC resistance
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(7/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(M characteristic product, T dimension of the product 0.75mm max.)
MLP1005Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
2.0
1.8
1.6
1.4
1.2
1.0
1.0μH
0.8
0.6
0.4
0.2
0.0
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(8/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(M characteristic product, T dimension of the product 0.75mm max.)
MLP1005 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
2.0
1.8
1.6
1.4
1.2
1.0
1.0μH
0.8
0.6
0.4
0.2
0.0
0
200
400
600
800
1000
(
)
DC current mA
○ Measurement equipment
Product No.
Manufacturer
4285A+42841A+42842C+42851-61100
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(9/53)
I
N
D
U
C
T
O
R
S
MLPseries
MLP1608 Type
SHAPE & DIMENSIONS
0.30 0.20
0.30 0.20
1.60 0.15
T
0.60 0.15
0.80 0.15
Dimensions in mm
RECOMMENDED LAND PATTERN
Dimensions in mm
0.6
0.8
0.6
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(10/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
MLP1608 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
Thickness T
L
Measuring
frequency
(MHz)
2
2
2
2
2
2
DC resistance
(ꢂ) 30%
(mA)
max.
750
800
700
800
700
600
Type
(mm)
Part No.
max.
Low resistance 0.95
0.75
(μH)
2.2
0.47
1.0
tolerance
20%
20%
20%
20%
0.30
0.22
0.30
0.20
0.30
0.36
MLP1608H2R2BT0S1
MLP1608VR47DT0S1
MLP1608V1R0DT0S1
MLP1608VR47BT0S1
MLP1608V1R0BT0S1
MLP1608V2R2BT0S1
0.75
0.95
0.95
0.95
Emphasized
DC bias
characteristics
Low core loss
0.47
1.0
2.2
20%
20%
ꢀꢁ Rated current: Current assumed when temperature has risen to 40°C max.
○ Measurement equipment
Measurement item Product No.
Manufacturer
L
4294A+16034G
Type-7561
Agilent Technologies
Yokogawa
DC resistance
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(11/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 0.95mm max.)
MLP1608Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
3.0
2.5
2.2μH
2.0
1.5
1.0
0.5
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
4294A+16034G
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(12/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 0.95mm max.)
MLP1608 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.0
2.5
2.0
2.2μH
1.5
1.0
0.5
0.0
0
200
400
600
800
1000
(m )
A
DC current
○ Measurement equipment
Product No.
Manufacturer
4285A+42841A+42842C+42851-61100
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(13/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 0.75mm max.)
MLP1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
1.2
1.0μH
1.0
0.8
0.6
0.47μH
0.4
0.2
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(14/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 0.75mm max.)
MLP1608 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
200
400
600
800
1000
(
)
DC current mA
○ Measurement equipment
Product No.
Manufacturer
4285A+42841A+42842C+42851-61100
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(15/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 0.95mm max.)
MLP1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
3.0
2.5
2.2μH
2.0
1.5
1.0μH
1.0
0.47μH
0.5
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(16/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 0.95mm max.)
MLP1608 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
200
400
600
800
1000
(
)
DC current mA
○ Measurement equipment
Product No.
Manufacturer
4285A+42841A+42842C+42851-61100
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(17/53)
I
N
D
U
C
T
O
R
S
MLPseries
MLP2012 Type
SHAPE & DIMENSIONS
0.50 0.30
0.50 0.30
2.00 0.20
T
0.50 0.05
0.85 0.15
Dimensions in mm
RECOMMENDED LAND PATTERN
0.8
1.0
0.8
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(18/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
MLP2012Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
(mA)
max.
1300
1300
1100
1100
1000
700
1100
900
800
700
600
1200
1200
800
700
600
1200
1000
1000
800
900
700
Thickness T
L
Measuring
frequency
(MHz)
DC resistance
(ꢂ) 30%
Type
(mm)
max.
1.0
Part No.
(μH)
0.47
0.54
1.0
tolerance
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0.07
0.065
0.12
0.12
0.15
0.26
0.11
0.20
0.23
0.28
0.40
0.13
0.13
0.23
0.27
0.33
0.09
0.16
0.16
0.23
0.19
0.26
MLP2012HR47MT0S1
MLP2012HR54MT0S1
MLP2012H1R0MT0S1
MLP2012H1R5MT0S1
MLP2012H2R2MT0S1
MLP2012V1R0TT0S1
MLP2012VR47MT0S1
MLP2012V1R0MT0S1
MLP2012V1R5MT0S1
MLP2012V2R2MT0S1
MLP2012V4R7MT0S1
MLP2012SR47TT0S1
MLP2012SR82TT0S1
MLP2012S1R0TT0S1
MLP2012S1R5TT0S1
MLP2012S2R2TT0S1
MLP2012SR47MT0S1
MLP2012S1R0MT0S1
MLP2012S1R5MT0S1
MLP2012S2R2MT0S1
MLP2012S3R3MT0S1
MLP2012S4R7MT0S1
1.0
Low resistance 1.0
1.0
1.5
1.0
2.2
Low core loss
0.55
1.0
1.0
1.0
0.47
1.0
Emphasized
DC bias
characteristics
1.0
1.5
1.0
2.2
1.0
4.7
0.55
0.55
0.55
0.55
0.55
1.0
0.47
0.82
1.0
1.5
2.2
STD product
0.47
1.0
1.0
1.0
1.5
1.0
2.2
1.0
3.3
1.0
4.7
ꢀꢁ Rated current: Current assumed when temperature has risen to 40°C max.
○ Measurement equipment
Measurement item Product No.
Manufacturer
L
4294A+16034G
Type-7561
Agilent Technologies
Yokogawa
DC resistance
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(19/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.0mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
3.0
2.5
2.2μH
2.0
1.5μH
1.5
1.0μH
1.0
0.54μH
0.5
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(20/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.0mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.0
2.5
2.2μH
2.0
1.5μH
1.5
1.0μH
1.0
0.54μH
0.5
0.47μH
0.0
0
250
500
750
1000
1250
1500
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(21/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 0.55mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(22/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 0.55mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(23/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.0mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
7.0
6.0
5.0
4.7μH
4.0
3.0
2.2μH
2.0
1.5μH
1.0μH
1.0
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(24/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.0mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
5.0
4.5
4.7μH
4.0
3.5
3.0
2.5
2.2μH
2.0
1.5
1.0
0.5
0.0
1.5μH
1.0μH
0.47μH
0
250
500
750
DC current mA
1000
1250
1500
(
)
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(25/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 0.55mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
3.0
2.5
2.2μH
2.0
1.5μH
1.5
1.0μH
1.0
0.82μH
0.5
0.0
0.47μH
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(26/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 0.55mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.0
2.5
2.2μH
2.0
1.5μH
1.5
1.0μH
1.0
0.82μH
0.5
0.47μH
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(27/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.0mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
6.0
5.0
4.7μH
4.0
3.3μH
3.0
2.2μH
2.0
1.5μH
1.0μH
1.0
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(28/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.0mm max.)
MLP2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
6.0
5.0
4.7μH
4.0
3.3μH
3.0
2.2μH
2.0
1.5μH
1.0μH
1.0
0.47μH
0.0
0
250
500
750
1000
1250
1500
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(29/53)
I
N
D
U
C
T
O
R
S
MLPseries
MLP2016 Type
SHAPE & DIMENSIONS
0.50 0.30
0.50 0.30
2.00 0.20
Dimensions in mm
RECOMMENDED LAND PATTERN
Dimensions in mm
0.8
1
0.8
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(30/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
MLP2016 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
(mA)
max.
1700
1300
1200
1200
1200
1100
1500
1200
1150
1000
1600
1400
1200
1200
800
Thickness T
L
Measuring
frequency
(MHz)
DC resistance
(ꢂ)
Type
(mm)
max.
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
Part No
(μH)
0.47
1.0
1.5
2.2
3.3
4.7
0.47
1.0
1.5
2.2
0.47
1.0
1.5
2.2
tolerance
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
0.055 25%
0.09 25%
0.11 25%
0.11 25%
0.12 25%
0.16 25%
0.07 25%
0.12 25%
0.14 25%
0.17 25%
0.05 30%
0.09 30%
0.09 30%
0.11 30%
0.27 30%
MLP2016HR47MT0S1
MLP2016H1R0MT0S1
MLP2016H1R5MT0S1
MLP2016H2R2MT0S1
MLP2016H3R3MT0S1
MLP2016H4R7MT0S1
MLP2016VR47MT0S1
MLP2016V1R0MT0S1
MLP2016V1R5MT0S1
MLP2016V2R2MT0S1
MLP2016SR47MT0S1
MLP2016S1R0MT0S1
MLP2016S1R5MT0S1
MLP2016S2R2MT0S1
MLP2016S4R7MT0S1
Low resistance
Low core loss
Emphasized
DC bias
characteristics
STD product
4.7
ꢀꢁ Rated current: Current assumed when temperature has risen to 40°C max.
○ Measurement equipment
Measurement item Product No.
Manufacturer
L
4294A+16034G
Type-7561
Agilent Technologies
Yokogawa
DC resistance
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(31/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.0mm max.)
MLP2016 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
8.0
7.0
6.0
5.0
4.7μH
4.0
3.3μH
3.0
2.2μH
2.0
1.5μH
1.0
1.0μH
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(32/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.0mm max.)
MLP2016 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH (EXAMPLE)
5.0
4.5
4.7μH
4.0
3.5
3.3μH
3.0
2.5
2.2μH
2.0
1.2μH
1.5
1.0
1.0μH
0.5
0.0
0
250
500
750
1000
1250
1500
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(33/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.0mm max.)
MLP2016 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
3.5
3.0
2.5
2.2μH
2.0
1.5μH
1.5
1.0μH
1.0
0.47μH
0.5
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(34/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.0mm max.)
MLP2016 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0
250
500
750
1000
1250
1500
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(35/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.0mm max.)
MLP2016 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
7.0
6.0
5.0
4.7μH
4.0
3.0
2.2μH
2.0
1.5μH
1.0μH
1.0
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(36/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.0mm max.)
MLP2016 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
7.0
6.0
5.0
4.7μH
4.0
3.0
2.2μH
2.0
1.5μH
1.0μH
1.0
0.47μH
0.0
0
250
500
750
1000
1250
1500
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(37/53)
I
N
D
U
C
T
O
R
S
MLPseries
MLP2520 Type
SHAPE & DIMENSIONS
0.50 0.30
0.50 0.30
2.50 0.15
T
0.85 0.15
1.10 0.10
Dimensions in mm
RECOMMENDED LAND PATTERN
0.7
1.4
0.7
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(38/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
MLP2520 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
(mA)
max.
2300
2300
2100
1500
1300
1000
1000
1600
1500
1000
1700
1300
1400
1100
900
Thickness T
L
Measuring
frequency
(MHz)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
DC resistance
(ꢂ) 30%
Type
(mm)
max.
1.0
1.2
1.0
1.0
1.0
1.0
1.0
1.2
1.2
1.2
1.0
1.0
1.0
1.0
1.0
1.0
1.2
1.2
1.2
1.2
1.0
1.0
1.0
1.0
1.0
1.0
1.2
1.2
1.2
1.2
1.2
Part No.
(μH)
1.0
tolerance
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
20%
0.048
0.048
0.044
0.075
0.09
0.13
0.13
0.07
0.08
0.13
0.06
0.10
0.10
0.12
0.20
0.24
0.10
0.10
0.12
0.22
0.085
0.09
0.09
0.13
0.13
0.28
0.08
0.11
0.11
0.11
0.28
MLP2520K1R0MT0S1
MLP2520K1R0ST0S1
MLP2520HR47MT0S1
MLP2520H1R0MT0S1
MLP2520H2R2MT0S1
MLP2520H3R3MT0S1
MLP2520H4R7MT0S1
MLP2520H1R0ST0S1
MLP2520H2R2ST0S1
MLP2520H4R7ST0S1
MLP2520VR47MT0S1
MLP2520V1R0MT0S1
MLP2520V1R5MT0S1
MLP2520V2R2MT0S1
MLP2520V3R3MT0S1
MLP2520V4R7MT0S1
MLP2520V1R0ST0S1
MLP2520V1R5ST0S1
MLP2520V2R2ST0S1
MLP2520V4R7ST0S1
MLP2520S1R0MT0S1
MLP2520S1R5MT0S1
MLP2520S2R2MT0S1
MLP2520S3R3MT0S1
MLP2520S4R7MT0S1
MLP2520S100MT0S1
MLP2520S1R0ST0S1
MLP2520S2R2ST0S1
MLP2520S3R3ST0S1
MLP2520S4R7ST0S1
MLP2520S100ST0S1
Large current
Low resistance
1.0
0.47
1.0
2.2
3.3
4.7
1.0
2.2
4.7
0.47
1.0
1.5
2.2
3.3
4.7
1.0
1.5
2.2
4.7
1.0
1.5
2.2
3.3
4.7
Emphasized
low resistance
Low core loss
Emphasized
DC bias
characteristics
800
1300
1400
1100
800
1500
1200
1200
1000
1000
700
1500
1200
1000
1000
700
STD product
10.0
1.2
2.5
3.3
4.7
2
2
10.0
ꢀꢁ Rated current: Current assumed when temperature has risen to 40°C max.
○ Measurement equipment
Measurement item Product No.
Manufacturer
L
4294A+16034G
Type-7561
Agilent Technologies
Yokogawa
DC resistance
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(39/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(K characteristic product)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
K1R0S
K1R0M
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(40/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(K characteristic product)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
2.0
1.8
1.6
1.4
1.2
K1R0S
1.0
K1R0M
0.8
0.6
0.4
0.2
0.0
0
500
1000
1500
2000
2500
3000
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(41/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.0mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
12.0
10.0
8.0
6.0
4.7μH
4.0
3.3μH
2.2μH
2.0
1.0μH
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(42/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.0mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
6.0
5.0
4.0
3.0
2.0
1.0
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(43/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.2mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
12.0
10.0
8.0
6.0
4.7μH
4.0
2.2μH
1.0μH
2.0
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(44/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(H characteristic product, T dimension of the product 1.2mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
6.0
5.0
4.0
3.0
2.0
1.0
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(45/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.0mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
12.0
10.0
8.0
6.0
4.7μH
4.0
3.3μH
1.0μH
2.2μH
2.0
1.5μH
0.47μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
4294A+16034G
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(46/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.0mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
6.0
5.0
4.0
3.0
2.0
1.0
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(47/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.2mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
12.0
10.0
8.0
6.0
4.7μH
4.0
2.2μH
2.0
0.0
1.5μH
1.0μH
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(48/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(V characteristic product, T dimension of the product 1.2mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
6.0
5.0
4.7μH
4.0
3.0
2.2μH
2.0
1.5μH
1.0μH
1.0
0.0
0
250
500
750
1000
1250
1500
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(49/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.0mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
14.0
12.0
10μH
10.0
8.0
6.0
4.7μH
4.0
2.0
0.0
3.3μH
2.2μH
1.5μH
1.0μH
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
4294A+16034G
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(50/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.0mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
14.0
12.0
10.0
8.0
6.0
4.0
2.0
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(51/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.2mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
14.0
12.0
10μH
10.0
8.0
6.0
4.7μH
4.0
3.3μH
2.2μH
2.0
1.0μH
0.0
0.1
1
10
100
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A+16034G
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(52/53)
I
N
D
U
C
T
O
R
S
MLPseriesꢀ
(S characteristic product, T dimension of the product 1.2mm max.)
MLP2520 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
14.0
12.0
10.0
8.0
6.0
4.0
2.0
0.0
0
200
400
600
800
1000
1200
(
)
DC current mA
○ Measurement equipment
Product No.
4285A+42841A+42842C+42851-61100
Manufacturer
Agilent Technologies
* Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
(53/53)
I
N
D
U
C
T
O
R
S
MLPseries
Packaging Style
REEL DIMENSIONS
1.0
+2.0
2.0 0.5
ø13 0.2
ø21 0.8
8.4
–0.0
14.4max.
ø180 2.0
Dimensions in mm
TAPE DIMENSIONS
+0.1
1.5
Sprocket hole
Cavity
–0.0
Type
A
B
K
MLP1005
MLP1608
MLP2012
MLP2016
MLP2520
1.15 0.1
1.9 0.2
2.3 0.2
2.3 0.2
2.7 0.1
0.65 0.1
1.1 0.2
1.5 0.2
1.5 0.2
2.3 0.2
1.0 max.
1.1max.
1.1max.
1.1max.
1.5max.
K
B
4.0 0.1
2.0 0.05
2.0 0.05
200min.
160min.
Taping
300min.
Drawing direction
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20140402 / inductor_commercial_power_mlp_en.
相关型号:
©2020 ICPDF网 联系我们和版权申明