SLF6028T-100M1R3-PF_16 [TDK]
Inductors for Power Circuits Wound Ferrite;型号: | SLF6028T-100M1R3-PF_16 |
厂家: | TDK ELECTRONICS |
描述: | Inductors for Power Circuits Wound Ferrite |
文件: | 总9页 (文件大小:147K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
I
N
D
U
C
T
O
R
S
April 2016
Inductors for Power Circuits
Wound Ferrite
SLF Series
SLF6028 Type
SLF6028
(2/9)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 30°C, Humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20160411 / inductor_commercial_power_slf6028_en.
(3/9)
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive
Compatible with lead-free solders
Inductors for Power Circuits
Wound Ferrite
Overview of SLF6028 Type
FEATURES
Magnetic shield type wound inductor for power circuits.
Product lineup allows for various usages.
APPLICATION
Thin-screen TV, LCDs, AV equipment, gaming equipment, other electrical devices
PART NUMBER CONSTRUCTION
SLF
6028
T
-
4R7
M
1R6
-
PF
L×W×H Dimensions
(mm)
Inductance
(μH)
Rated current
(A)
Inductance
tolerance
Series name
Packaging style
Internal code
6028
6.0×6.0×2.8
T
Taping
4R7
100
101
4.7
10
100
M
N
20%
30%
R47
1R6
150
0.47
1.6
15
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating Storage
Type
ꢀ
ꢀꢀ
temperature
temperature
(pieces/reel)
(°C)
(°C)
(g)
SLF6028
–40 to +105
–40 to +105
1000
0.3
ꢀꢁ
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
ꢀꢀꢁ
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
(4/9)
I
N
D
U
C
T
O
R
S
SLF6028 Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30s
Time
t3
5s
T2
180°C
150°C
230°C
250°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
(5/9)
I
N
D
U
C
T
O
R
S
SLF6028 Type
SHAPE & DIMENSIONS
6
0.2
0.9
4
0.9
Dimensions in mm
RECOMMENDED LAND PATTERN
1.5
4
1.5
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
(6/9)
I
N
D
U
C
T
O
R
S
SLF6028 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated currentꢀ
L
L measuring frequency
DC resistance
Part No.
Isat
(A)max.
1.6
1.5
1.3
Itemp
(A)max.
2.5
2.2
1.8
1.4
1.3
1.1
0.92
0.78
0.64
0.5
(μH)
4.7
6.8
10
15
22
33
47
68
Tolerance
20%
20%
20%
20%
20%
20%
20%
20%
(kHz)
(ꢂ) 20%
0.0284
0.0354
0.0532
0.0745
0.104
0.148
0.21
0.29
0.43
0.65
0.98
100
100
100
100
100
100
100
100
100
100
100
SLF6028T-4R7M1R6-PF
SLF6028T-6R8M1R5-PF
SLF6028T-100M1R3-PF
SLF6028T-150M1R0-PF
SLF6028T-220MR77-PF
SLF6028T-330MR69-PF
SLF6028T-470MR59-PF
SLF6028T-680MR50-PF
SLF6028T-101MR42-PF
SLF6028T-151MR34-PF
SLF6028T-221MR26-PF
1
0.77
0.69
0.59
0.5
0.42
0.34
0.26
100
150
220
20%
20%
20%
0.38
ꢀꢁ Rated current: smaller value of either Isat or Itemp.
Isat: When based on the inductance change rate (30% below the nominal value)
Itemp: When based on the temperature increase (Temperature increase of 25°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4194A
VP-2941A
4284A+42841A+42842C
Keysight Technologies
Panasonic
Keysight Technologies
DC resistance
Rated current Isat
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
(7/9)
I
N
D
U
C
T
O
R
S
SLF6028 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
1000
221M
151M
100
101M
680M
470M
330M
220M
150M
10
100M
6R8M
4R7M
1
1
10
100
1000
10000
100000
1000000
(
)
Frequency kHz
○ Measurement equipment
Product No.
4294A
Manufacturer
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
(8/9)
I
N
D
U
C
T
O
R
S
SLF6028 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
1000
221M
151M
100
101M
680M
470M
330M
220M
150M
10
100M
6R8M
4R7M
1
0.0
0.5
1.0
1.5
2.0
2.5
( )
DC current A
○ Measurement equipment
Product No.
Manufacturer
4284A+42841A+42842C
Keysight Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
(9/9)
I
N
D
U
C
T
O
R
S
SLF6028 Type
PACKAGING STYLE
REEL DIMENSIONS
2.0 0.5
E
Type
SLF6028
A
ø330
W1
16.4
W2
22.4
N
ø50
E
2
* These values are typical values.
(
)
1.0
ø13.0 0.5
ø21.0 0.8
W1
W2
A
Dimensions in mm
TAPE DIMENSIONS
øD0
P2
P0
P1
K
t
Dimensions in mm
A
Type
A
B
øD0
E
F
P0
P1
P2
W
K
t
SLF6028 6.4
6.4 1.5+0.1/-0 1.75 0.1 7.5 0.1 4.0 0.1 12.0 0.1 2.0 0.05 16.0 0.3 3.1
0.4
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160411 / inductor_commercial_power_slf6028_en.
相关型号:
UL1042
UL1042 - Uk砤d zr體nowa縪nego mieszacza iloczynowegoWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV201
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14
IC-SM-VIDEO AMPWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TA
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
ZXFV201N14TC
QUAD VIDEO AMPLIFIERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV302N16
IC-SM-4:1 MUX SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ZXFV4089
VIDEO AMPLIFIER WITH DC RESTORATIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ZETEX
©2020 ICPDF网 联系我们和版权申明