SPM6530T-R68M140 [TDK]
General Purpose Inductor, 0.68uH, 20%, 1 Element, Ferrite-Core, SMD, 6530, HALOGEN FREE AND ROHS COMPLIANT;
| 型号： | SPM6530T-R68M140 |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | General Purpose Inductor, 0.68uH, 20%, 1 Element, Ferrite-Core, SMD, 6530, HALOGEN FREE AND ROHS COMPLIANT 测试 功率感应器 电感器 |
| 文件： | 总25页 (文件大小：190K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
I
N
D
U
C
T
O
R
S
December 2013
Inductors for Power Circuits
Wound Metallic Magnetic Material
SPMseries
SPM3012 (3.2x3.0 mm)
SPM4012 (4.4x4.1 mm)
SPM5012 (5.4x5.1 mm)
SPM5030 (5.2x5.0 mm)
SPM6530 (7.1x6.5 mm)
(2/25)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(3/25)
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive
Halogen-free
Inductors for Power Circuits
Wound Metallic Magnetic Material
Compatible with lead-free solders
Overview of the SPM Series
FEATURES
Magnetic shield type wound inductor for power circuits using a metallic magnetic material.
Low-profile product lineup with max. heights of 1.2mm and 3.0mm allowing for different usages.
Compared to ferrite wound type inductors, it is possible to achieve large current, low Rdc, and compactness.
Low inductance variance in high-temperature environments with good DC superimposition characteristics.
Metallic magnetic material is used, and the structure has an integrated molded coil, so hum noise is lower than with core adhesive coils.
APPLICATION
Smart phones, tablet terminals, laptop computers, HDDs, servers, VRMs, compact power supply modules, other
PART NUMBER CONSTRUCTION
SPM
3012
T
-
1R0
M
L×W×H Dimensions
(mm max.)
Inductance
(μH)
Inductance
tolerance
Series name
Packaging style
3012
4012
5012
5030
6530
3.2×3.0×1.2
4.4×4.1×1.2
5.4×5.1×1.2
5.2×5.0×3.0
7.1×6.5×3.0
T
Taping
1R0
1R5
2R2
1.0
1.5
2.2
M
20%
SPM
6530
T
-
R25
M
230
L×W×H Dimensions
(mm max.)
Inductance
(μH)
Inductance
tolerance
Internal
code
Series name
Packaging style
Taping
6530
7.1×6.5×3.0
T
R25
0.25
M
20%
1R0
4R7
1.0
4.7
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating
temperature
Storage
temperature
Type
ꢀ
ꢀꢀ
(pieces/reel)
2000
（°C）
（°C）
（g）
0.047
0.0941
0.1500
0.364
0.656
SPM3012
SPM4012
SPM5012
SPM5030
SPM6530
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
1000
1000
500
1000
ꢀꢁ
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
ꢀꢀꢁ
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(4/25)
I
N
D
U
C
T
O
R
S
Overview of the SPM Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
120s
Time
t2
30s
Time
t3
10s max.
T2
180°C
150°C
230°C
260°C
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(5/25)
I
N
D
U
C
T
O
R
S
SPM series
SPM3012 Type
SHAPE & DIMENSIONS
(
)
3.2 0.1
0.85 0.1
1.5
0.85 0.1
Dimensions in mm
RECOMMENDED LAND PATTERN
1.1
1.5
1.1
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(6/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM3012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
DC resistance
Rated current(A)ꢀ
L measuring
frequency
(kHz)
L
(mꢂ )
max.
65
Part No.
max.
Idc1
3.4
typ.
Idc1
5.4
(μH)
1.0
1.5
2.2
3.3
4.7
Tolerance
20%
20%
20%
20%
typ.
57
Idc2
2.8
2.5
2.2
1.5
1.3
100
100
100
100
100
SPM3012T-1R0M
SPM3012T-1R5M
SPM3012T-2R2M
SPM3012T-3R3M
SPM3012T-4R7M
90
77
2.8
4.7
115
210
270
100
183
232
2.5
3.4
1.8
2.8
20%
1.5
2.6
ꢀꢁ Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4284A
AX-111A
4284A+42841A+42842C
Agilent Technologies
ADEX
Agilent Technologies
DC resistance
Rated current Idc1
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(7/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM3012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
25.0
4R7M
20.0
15.0
10.0
5.0
3R3N
2R2N
1R5N
1R0N
0.0
10
100
1000
10000
100000
(
)
Frequency kHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(8/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM3012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
5
4R7M
4
3R3M
3
2R2M
2
1R5M
1
1R0M
0
0
1
2
3
4
5
6
DC current(A)
○ Measurement equipment
Product No.
Manufacturer
4284A+42841A+42842C
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(9/25)
I
N
D
U
C
T
O
R
S
SPM series
SPM4012 Type
SHAPE & DIMENSIONS
(
)
4.4 0.2
0.9 0.1
2.6
0.9 0.1
Dimensions in mm
RECOMMENDED LAND PATTERN
1.65
1.65
1.65
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(10/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM4012Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
DC resistance
Rated current(A)ꢀ
Measuring
frequency
(kHz)
L
(mꢂ )
max.
25
Part No.
max.
Idc1
6.0
typ.
Idc1
8.0
6.0
4.8
4.4
3.5
2.5
(μH)
0.47
1.00
1.50
2.20
3.30
4.70
Tolerance
20%
20%
20%
20%
typ.
23
Idc2
5.6
4.3
3.5
2.9
2.4
2.0
100
100
100
100
100
100
SPM4012T-R47M
SPM4012T-1R0M
SPM4012T-1R5M
SPM4012T-2R2M
SPM4012T-3R3M
SPM4012T-4R7M
45
70
95
38
59
82
4.8
3.5
3.3
2.8
20%
20%
145
205
123
178
2.0
ꢀꢁ Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4284A
AX-111A
4284A+42841A+42842C
Agilent Technologies
ADEX
Agilent Technologies
DC resistance
Rated current Idc1
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(11/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM4012Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
20.0
4R7M
15.0
10.0
5.0
3R3M
2R2M
1R5M
1R0M
4R7M
0.0
10
100
1000
10000
100000
(
)
Frequency kHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(12/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM4012Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
5
4R7M
4
3R3M
3
2R2M
2
1R5M
1R0M
1
R47M
0
0
2
4
6
8
10
12
DC current(A)
○ Measurement equipment
Product No.
Manufacturer
4284A+42841A+42842C
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(13/25)
I
N
D
U
C
T
O
R
S
SPM series
SPM5012 Type
SHAPE & DIMENSIONS
(
)
1.2 0.1
3.0
1.2 0.1
5.4 0.2
Dimensions in mm
RECOMMENDED LAND PATTERN
1.4
3.0
1.4
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(14/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM5012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
DC resistance
Rated current(A)ꢀ
Measuring
frequency
(kHz)
L
(mꢂ )
max.
44.0
Part No.
max.
Idc1
6.3
typ.
Idc1
7.9
(μH)
1.00
2.20
Tolerance
20%
20%
typ.
40.0
71.6
Idc2
4.1
2.7
100
100
SPM5012T-1R0M
SPM5012T-2R2M
78.8
4.9
6.1
ꢀꢁ Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (30% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4284A
AX-111A
4284A+42841A+42842C
Agilent Technologies
ADEX
Agilent Technologies
DC resistance
Rated current Idc1
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(15/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM5012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
8.0
6.0
4.0
2R2M
2.0
1R0M
0.0
10
100
1000
10000
100000
(
)
Frequency kHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(16/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM5012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
3.0
2.5
2R2M
2.0
1.5
1R0M
1.0
0.5
0.0
0
2
4
6
8
10
DC current(A)
○ Measurement equipment
Product No.
Manufacturer
4284A+42841A+42842C
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(17/25)
I
N
D
U
C
T
O
R
S
SPM series
SPM5030 Type
SHAPE & DIMENSIONS
(
)
1.15 0.2
2.9
1.15 0.2
5.2 0.3
R20
Dimensions in mm
RECOMMENDED LAND PATTERN
1.5
2.7
1.5
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(18/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM5030 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
DC resistance
Rated current(A)ꢀ
Measuring
frequency
(kHz)
L
(mꢂ)
max.
2.31
4.29
9.35
Part No.
typ.
Idc1
21.0
14.9
9.7
(μH)
0.20
0.35
0.75
1.0
Tolerance
20%
20%
20%
20%
typ.
2.1
3.9
8.5
10.4
Idc2
22.2
16.6
11.3
10.1
100
100
100
100
SPM5030T-R20M
SPM5030T-R35M
SPM5030T-R75M
SPM5030T-1R0M
11.44
8.5
ꢀꢁ Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (20% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4284A
AX-111A
4284A+42841A+42842C
Agilent Technologies
ADEX
Agilent Technologies
DC resistance
Rated current Idc1
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(19/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM5030 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
2.0
1.5
1R0M
1.0
R70M
0.5
R35M
R20M
0.0
10
100
1000
10000
100000
(
)
Frequency kHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(20/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM5030 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
1.2
1R0M
1.0
0.8
R75M
0.6
0.4
0.2
0.0
R35M
R20M
0
5
10
15
DC current(A)
20
25
30
○ Measurement equipment
Product No.
4284A+42841A+42842C
Manufacturer
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(21/25)
I
N
D
U
C
T
O
R
S
SPM series
SPM6530 Type
SHAPE & DIMENSIONS
(
)
1.55 0.3
3.8
1.55 0.3
7.1 0.3
R25
Dimensions in mm
RECOMMENDED LAND PATTERN
1.85
3.7
1.85
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(22/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM6530 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
DC resistance
Rated current(A)ꢀ
Measuring
frequency
(kHz)
L
(mꢂ)
max.
2.31
3.63
5.39
7.81
10.67
19
Part No.
typ.
Idc1
28.5
20.5
16.6
14.1
11.5
8.4
(μH)
0.25
0.47
0.68
1.0
1.5
2.2
3.3
4.7
Tolerance
20%
20%
20%
20%
20%
20%
20%
20%
typ.
2.1
3.3
4.9
7.1
9.7
17.3
27
Idc2
23
20
16
13
100
100
100
100
100
100
100
100
SPM6530T-R25M230
SPM6530T-R47M170
SPM6530T-R68M140
SPM6530T-1R0M120
SPM6530T-1R5M100
SPM6530T-2R2M
11
8.2
6.8
5.6
29.7
39.4
7.3
6.2
SPM6530T-3R3M
SPM6530T-4R7M
35.8
ꢀꢁ Rated current: smaller value of either Idc1 or Idc2.
Idc1: When based on the inductance change rate (20% below the initial value)
Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating)
・The cleaning agent can not be used for these products.
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4284A
AX-111A
4284A+42841A+42842C
Agilent Technologies
ADEX
Agilent Technologies
DC resistance
Rated current Idc1
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(23/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM6530 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
30.0
4R7M
25.0
20.0
15.0
10.0
5.0
3R3M
2R2M
R25M
R47M
1R5M
1R0M
R68M
0.0
10
100
1000
10000
100000
(
)
Frequency kHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(24/25)
I
N
D
U
C
T
O
R
S
SPM seriesꢀ
SPM6530 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
5.0
4R7M
4.5
4.0
3.5
3R3M
3.0
2.5
2.0
1.5
1.0
0.5
0.0
2R2M
1R5M
1R0M
R68M
R47M
R25M
0
10
20
30
40
50
DC current(A)
○ Measurement equipment
Product No.
Manufacturer
4284A+42841A+42842C
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
(25/25)
I
N
D
U
C
T
O
R
S
SPM series
Packaging Style
REEL DIMENSIONS
2.0 0.5
E
Type
A
W1
9.5
12.4
12.4
12.4
16.4
W2
N
E
SPM3012 ø180
SPM4012 ø180
SPM5012 ø180
SPM5030 ø180
SPM6530 ø330
11.9
14.4
14.4
14.4
20.4
ø60
ø60
ø60
ø60
ø100
1.2
1.0
1.0
1.0
2.0
* These values are typical values.
(
)
1.0
ø13.0 0.5
ø21.0 0.8
W1
W2
A
Dimensions in mm
TAPE DIMENSIONS
øD0
P2
P0
P1
K
t
Dimensions in mm
A
Type
A
B
øD0
E
F
P0
P1
P2
W
K
t
SPM3012 3.2
SPM4012 4.35 4.65
SPM5012 5.4
SPM5030 5.3
SPM6530 7.4
3.4
1.5+0.1/-0 1.75 0.1 3.50 0.1 4.0 0.05
1.5+0.1/-0 1.75 0.1 5.5 0.1 4.0 0.1
1.5+0.1/-0 1.75 0.1 5.5 0.1 4.0 0.1
1.5+0.1/-0 1.75 0.1 5.5 0.1 4.0 0.1
1.5+0.1/-0 1.75 0.1 7.5 0.1 4.0 0.1
4.0 0.05 2.0 0.1 8.0 0.1 1.35 0.25
8.00 0.1 2.0 0.1 12.0 0.2 1.35 0.3
5.7
5.5
7.6
8.00 0.1 2.0 0.1 12.0 0.2 3.3
8.00 0.1 2.0 0.1 12.0 0.2 3.3
12.0 0.1 2.0 0.1 16.0 0.3 3.6
1.5
0.4
0.4
• All specifications are subject to change without notice.
001-01 / 20131226 / inductor_commercial_power_spm_en.
相关型号：
©2020 ICPDF网 联系我们和版权申明