TPL802727 [TDK]
Transponder Coils;
| 型号： | TPL802727 |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | Transponder Coils |
| 文件： | 总13页 (文件大小：125K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
I
N
D
U
C
T
O
R
S
November 2013
Transponder Coils
TPLseries
TPL802727
TPL1183427
TPL1183525
(2/13)
I
N
D
U
C
T
O
R
S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
If an ultrasonic process is used, thoroughly check the condition setting in order to prevent disconnection.
Do not clean the products with solvents. If a potting resin or a moisture-proof coat containing a solvent such as acetone, toluene or
xylene is used, consult with us in advance.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(3/13)
I
N
D
U
C
T
O
R
S
Product compatible with RoHS directive
AEC-Q200
Transponder Coils
Overview of the TPL Series
FEATURES
Common in the series
Transponder coils that ensure high reliability suitable for automotive applications. TPL802727 type coils also realize a small size (8 mm
in length) and high inductance (18.52mH max.)
Achieves stable electrical characteristics due to their high SRF design structure.
TPL802727 type
Ensures high reliability suitable for automotive applications by adopting higher heat resistance wire and welding wire connection.
TPL1183427, TPL1183525 types
It is fully resin-molded.
Terminals are highly reliable with the spring structure. They show excellent quality especially in bending and drop resistance.
APPLICATION
Mainly receiving LF antenna coils for the in-car devices shown below
Tire-pressure monitoring system (TPMS)
Keyless entry system
Immobilizer etc.
Other electronic devices
PART NUMBER CONSTRUCTION
-
TPL
802727
722
H
L×W×H Dimensions
(mm)
Inductance
(mH)
Inductance tolerance
(%)
Series name
802727
1183427
1183525
8.0×2.7×2.7
11.8×3.4×2.75
11.8×3.5×2.4
722
7.2
H
J
3
5
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Operating
temperature
Storage
temperature
Type
ꢀ
（°C）
（°C）
（pieces/reel）
2,500
TPL802727
TPL1183427
TPL1183525
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
–40 to +125
2,500
2,500
ꢀꢁ
Operating temperature range includes self-temperature rise.
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(4/13)
I
N
D
U
C
T
O
R
S
TPL series
TPL802727 Type
SHAPE & DIMENSIONS
7.85 0.15
0.8
1.9
Dimensions in mm
RECOMMENDED LAND PATTERN
5.3
9.5
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(5/13)
I
N
D
U
C
T
O
R
S
TPL seriesꢀ
TPL802727 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Q
DC resistance
Lꢀ
Measurement frequency
(kHz)
(ꢂ)
max.
240
105
85
Part No.
(mH)
18.52
7.20
4.91
4.50
ꢀꢁ
Tolerance
3%
3%
3%
3%
min.
40
35
30
30
125
125
125
125
TPL802727-193H
TPL802727-722H
TPL802727-492H
TPL802727-452H
80
This inductance value is an example of the current commercial product.If a different inductance is needed, please contact us.
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(6/13)
I
N
D
U
C
T
O
R
S
TPL seriesꢀ
TPL802727 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
125kHz
30
25
20
15
10
5
722H
193H
492H
452H
0
10
100
1000
10000
(
)
Frequency kHz
Q FREQUENCY CHARACTERISTICS GRAPH
125kHz
75
50
25
0
193H
722H
492H
452H
10
100
1000
10000
(
)
Frequency kHz
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(7/13)
I
N
D
U
C
T
O
R
S
TPL series
TPL1183427 Type
SHAPE & DIMENSIONS
11.8 0.4
3.4 0.4
0.8
2.4
Dimensions in mm
RECOMMENDED LAND PATTERN
9.9
13.5
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(8/13)
I
N
D
U
C
T
O
R
S
TPL seriesꢀ
TPL1183427 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Lꢀ
Q
Self-resonant frequency
DC resistance
[125kHz]
typ.
66
(kHz)
typ.
690
(ꢂ)
typ.
50
[125kHz]
(mH)
7.20
Part No.
Tolerance
5%
TPL1183427-722J-720N
ꢀꢁ This inductance value is an example of the current commercial product.If a different inductance is needed, please contact us.
ꢀꢁ Available for an inductance tolerance of less than 5%.
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L, Q
4194A+16047E
4194A+16047E
AX-114N
Agilent Technologies
Agilent Technologies
ADEX
Self-resonant frequency
DC resistance
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(9/13)
I
N
D
U
C
T
O
R
S
TPL seriesꢀ
TPL1183427 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
125kHz
20
15
10
5
0
10
100
1000
(
)
Frequency kHz
○ Measurement equipment
Product No.
Manufacturer
4194A+16047E
Agilent Technologies
＊ Equivalent measurement equipment may be used.
Q FREQUENCY CHARACTERISTICS GRAPH
125kHz
100
80
60
40
20
0
10
100
1000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4194A+16047E
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(10/13)
I
N
D
U
C
T
O
R
S
TPL series
TPL1183525 Type
SHAPE & DIMENSIONS
11.8 0.5
3.5 0.4
0.8
3.2
Dimensions in mm
RECOMMENDED LAND PATTERN
9.9
13.5
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(11/13)
I
N
D
U
C
T
O
R
S
TPL seriesꢀ
TPL1183525 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Q
Lꢀ
Self-resonant frequency
DC resistance
[125kHz]
typ.
50
53
(kHz)
typ.
650
1100
(ꢂ)
typ.
26
[125kHz]
(mH)
2.61
Part No.
Tolerance
5%
3%
TPL1183525-262J-261N
TPL1183525-242Y-236N
2.36
24
ꢀꢁ This inductance value is an example of the current commercial product.If a different inductance is needed, please contact us.
ꢀꢁ Available for an inductance tolerance of less than 5%.
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L, Q
4194A+16047E
4194A+16047E
AX-114N
Agilent Technologies
Agilent Technologies
ADEX
Self-resonant frequency
DC resistance
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(12/13)
I
N
D
U
C
T
O
R
S
TPL seriesꢀ
TPL1183525 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
125kHz
20
15
10
5
261N
236N
0
10
100
1000
10000
(
)
Frequency kHz
○ Measurement equipment
Product No.
4194A+16047E
Manufacturer
Agilent Technologies
＊ Equivalent measurement equipment may be used.
Q FREQUENCY CHARACTERISTICS GRAPH
125kHz
100
80
60
40
20
0
236N
261N
10
100
1000
10000
(
)
Frequency kHz
○ Measurement equipment
Product No.
4194A+16047E
Manufacturer
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
(13/13)
I
N
D
U
C
T
O
R
S
TPL series
Packaging style
REEL DIMENSIONS
2.0 0.5
E
Type
A
W1
W2
N
E
2
TPL802727 ø329+0.5/–1.5 21.4 1.0 17.4 1.0 ø100 1.0
ø80 or
ø100 1.0
ø80 or
TPL1183427
TPL1183525
ø330 2.0
ø330 2.0
24.4+2.0/–0 29 2.0
24.4+2.0/–0 29 2.0
2
2
ø100 1.0
(
)
1.0
ø13.0 0.5
ø21.0 0.8
W1
W2
A
Dimensions in mm
TAPE DIMENSIONS
øD0
P2
P0
P1
K
t
Dimensions in mm
A
Dimensions in mm
Type
A
B
øD0
E
F
P0
P1
P2
W
K
t
TPL802727
TPL1183427
TPL1183525
3.0
3.7
3.7
8.1
12.1
12.1
1.5+0.1/–0
1.55 0.05
1.55 0.05
1.75 0.1
1.75 0.1
1.75 0.1
7.5 0.1
11.5 0.1
11.5 0.1
4.0 0.1
4.0 0.1
4.0 0.1
8.0 0.1
8.0 0.1
8.0 0.1
2.0 0.1
2.0 0.1
2.0 0.1
16.0 0.3
24 0.3
24 0.3
2.9
3.2
2.8
0.3
0.3
0.3
160min.
Taping
200min.
300min.
Drawing direction
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20131101 / e541_tpl.
相关型号：
©2020 ICPDF网 联系我们和版权申明