TIVH02L [TEKTRONIX]
Digital Phosphor Oscilloscopes;
| 型号： | TIVH02L |
| 厂家： | 
TEKTRONIX, INC. |
| 描述： | Digital Phosphor Oscilloscopes |
| 文件： | 总28页 (文件大小：3159K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Digital Phosphor Oscilloscopes
DPO7000 Series Datasheet
Key features
Ease of use features
®
Pinpoint Triggering provides the most flexible and highest
performance triggering, with over 1400 combinations to address
virtually any triggering situation
Visual Trigger and Search precisely qualifies triggers and finds
unique events in complex waveforms
Advanced Search and Mark to find specific events in the entire
waveform
®
MyScope custom control windows and right mouse click menus
for exceptional efficiency
53 automated measurements, waveform histograms, and FFT
analysis for simplified waveform analysis
®
TekVPI Probe Interface supports active, differential, and current
probes for automatic scaling and units
Tektronix understands that engineers rely on an oscilloscope throughout
their design cycle, from prototype turn-on to production testing. The
DPO7000 Series oscilloscopes' unique capabilities combined with
exceptional signal acquisition performance and analysis accelerate your
measurement tasks.
12.1 in. (307 mm) bright XGA display with touch screen
Optional serial triggering and analysis
Automated Serial Triggering, Decode, and Search Options for I2C,
SPI, CAN, LIN, FlexRay, RS-232/422/485/UART, MIL-STD-1553,
and USB 2.0
Notice to EU customers
®
Automated Serial Analysis Options for MIPI D-PHY DSI-1 and
This product is not updated to comply with the RoHS 2 Directive 2011/65/
EU and will not be shipped to the EU. Customers may be able to purchase
products from inventory that were placed on the EU market prior to
July 22, 2017 until supplies are depleted. Tektronix is committed to helping
you with your solution needs. Please contact your local sales
representative for further assistance or to determine if alternative product(s)
are available. Tektronix will continue service to the end of worldwide
support life.
CSI-2, 8b/10b, Ethernet, and PCI Express
Clock Recovery from serial data streams
64-bit NRZ Serial Pattern Trigger for isolation of pattern-dependent
effects up to 1.25 Gb/s
Optional technology specific analysis
®
Software Solutions provide built-in domain expertise for MIPI D-
PHY, Ethernet, Automotive Ethernet, MOST, and USB
2.0 Compliance Testing, Jitter, Timing, Eye Diagrams, Power, DDR
Memory Bus Analysis, and Wideband RF
Key performance specifications
3.5 GHz, 2.5 GHz, 1 GHz, and 500 MHz bandwidth models
Limit and Mask Testing provide quick insight into signal
characteristics
Up to 40 GS/s real-time sample rate on one channel, up to 20 GS/s on
two channels, and up to 10 GS/s on three or four channels
Connectivity
™
Up to 500 Megapoint record length with MultiView Zoom
USB Host Ports on the front and side panels for quick and easy data
storage, printing, and connecting USB peripherals
®
>250,000 wfms/s maximum waveform capture rate with FastAcq
™
FastFrame segmented memory acquisition mode with
Integrated 10/100/1000BASE-T Ethernet port for network connection
and Video Out port to export the oscilloscope display to a monitor or
projector
>310,000 waveforms per second capture rate
User-selectable bandwidth limit filters for better low-frequency
measurement accuracy
®
Microsoft Windows 10 operating system for easy connectivity and
integration into your environment
LXI Class C compliant
www.tek.com/DPO7000
1
Datasheet
™
TekScope Anywhere off-line analysis
™
TekScope Anywhere brings the power of the oscilloscope analysis
environment to the PC. Users now have the flexibility to perform analysis
tasks including timing, eye, and jitter analysis outside the lab. Waveform
data and setups 1 from Tektronix MDO3000, MDO4000, MSO/DPO5000,
DPO7000C, or MSO/DPO70000C/D/DX/SX Series oscilloscopes can
quickly be shared among team members and remote sites, resulting in
improved efficiency.
Simplified analysis for complex digital
designs
With the DPO7000C Digital Phosphor Oscilloscope Series, you can
analyze analog and serial bus signals with a single instrument to quickly
find and diagnose problems in complex designs. Bandwidths up to 3.5 GHz
and sample rates up to 40 GS/s ensure you have the performance you
need to see fast-changing signal details. To capture long windows of signal
activity while maintaining fine timing resolution, the DPO7000C Series
offers a deep record length of up to 25 M points standard on all channels
and an optional record length of up to 500 M points on one channel.
Discover – Fast waveform capture rate - over 250,000 wfm/s - maximizes the probability
of capturing elusive glitches and other infrequent events.
The DPO7000C Series offers the industry's most complete visualization of
signals, providing fast insight into the real operation of your device.
™
With Advanced Search and Mark and MultiView Zoom features for rapid
®
Tektronix proprietary FastAcq technology delivers a fast waveform
waveform navigation, and more than 15 optional software and analysis
packages for common technologies and in-depth analysis tasks, the
DPO7000C Series from Tektronix provides the feature-rich tools you need
to simplify and speed debug of your complex design.
capture – greater than 250,000 waveforms per second – that enables you
to see glitches and other infrequent transients within seconds, revealing the
true nature of device faults. A digital phosphor display with color intensity
grading shows the history of a signal's activity by using color to identify
areas of the signal that occur more frequently, providing a visual display of
just how often anomalies occur.
Comprehensive features speed every stage
of debug
Capture
The DPO7000C Series offers a robust set of features to speed every stage
of debugging your design – from quickly discovering an anomaly and
capturing it, to searching your waveform record for the event and analyzing
its characteristics and your device's behavior.
Discovering a device fault is only the first step. Next, you must capture the
event of interest to identify root cause.
The DPO7000C Series provides a complete set of triggers – including runt,
glitch, width, timeout, transition, pattern, state, setup/hold violation, window,
comm, and serial pattern – to help quickly find your event. Enhanced
Triggering reduces trigger jitter at the trigger point. In this mode, the trigger
point can be used as a measurement reference.
Discover
To debug a design problem, first you must know it exists. Every design
engineer spends time looking for problems in their design, a time-
consuming and frustrating task without the right debug tools.
1
Setups for MSO/DPO5000/B, DPO7000C, MSO/DPO70000C/D/DX/SX models only.
2 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Search
Finding your event of interest in a long waveform record can be time
consuming without the right search tools. With today's record lengths
pushing beyond a million data points, locating your event can mean
scrolling through thousands of screens of signal activity.
Capture – Triggering on a specific transmit data packet going across an RS-232 bus. A
complete set of triggers, including triggers for specific serial packet content, ensures you
quickly capture your event of interest.
To enable complex system debug and validation, the DPO7000C Series
®
provides Pinpoint triggering, using Silicon Germanium (SiGe) technology
to provide trigger performance up to the bandwidth of the oscilloscope and
over 1400 trigger combinations. Most other trigger systems offer multiple
trigger types only on a single event (A event), with the delayed trigger (B
event) selection limited to edge-type triggering, and often do not provide a
way to reset the trigger sequence if the B event doesn’t occur. But Pinpoint
triggering provides a full suite of advanced trigger types on both A and B
triggers with Reset triggering to begin the trigger sequence again after a
specified time, state, or transition so that even events in the most complex
signals can be captured.
Search – Results of an advanced search for a runt pulse or a narrow glitch within a long
waveform record. Each instance of the runt or glitch is automatically marked for easy
reference.
The DPO7000C Series offers the industry's most comprehensive search
and waveform navigation with the standard Advanced Search and Mark
feature and front-panel controls. User marks allow you to mark any location
that you may want to reference later for further investigation. Or,
automatically search your entire record for the criteria you define. Along the
way it will automatically mark every occurrence of your defined event so
you can quickly move between events. The advanced search and mark
capability of the DPO7000C Series can search for up to eight different
events simultaneously and stop a live acquisition when it finds an event of
interest, saving even more time.
Finding the right characteristic of a complex signal can require hours of
collecting and sorting through thousands of acquisitions for the event of
interest. Defining a trigger that isolates the desired event and shows data
only when the event occurs speeds up this process. Visual Trigger and
Search makes the identification of the desired waveform events quick and
easy by scanning through all waveform acquisitions and comparing them to
on-screen areas (geometric shapes).
Analyze
Verifying that your prototype's performance matches simulations and meets
the project's design goals requires analyzing its behavior. Tasks can range
from simple checks of rise times and pulse widths to sophisticated power
loss analysis, characterization of system clocks, and investigation of noise
sources. The DPO7000C Series offers a comprehensive set of integrated
analysis tools including waveform- and screen-based cursors,
53 automated measurements, advanced waveform math including arbitrary
equation editing, custom MATLAB and .NET math plug-in analysis
functions, waveform histograms, and FFT analysis.
With up to a 500 M point record length, you can capture many events of
interest, even thousands of serial packets, in a single acquisition for further
analysis while maintaining high resolution to zoom in on fine signal details.
Investigate multiple segments of your waveform capture simultaneously
™
™
with MultiView Zoom to quickly compare events in real time. FastFrame
Segmented Memory mode enables you to make efficient use of large
records by capturing many trigger events in a single record eliminating
large time gaps between events of interest. View and measure the
segments individually or as an overlay.
From triggering on specific packet content to automatic decode in multiple
data formats, the DPO7000C Series provides integrated support for a
broad range of serial buses – I2C, SPI, CAN, LIN, FlexRay,
RS-232/422/485/UART, MIL-STD-1553, Ethernet, USB 2.0, and MIPI D-
PHY. The ability to decode up to 16 serial buses simultaneously means you
gain insight into system-level problems quickly.
www.tek.com/DPO7000
3
Datasheet
Analyze – Waveform histogram of a falling edge showing the distribution of edge position
(jitter) over time. Included are numeric measurements made on the waveform histogram
data. A comprehensive set of integrated analysis tools speeds verification of your
design's performance.
Search step 1: You define what you would like to find.
User marks
Press the Set/Clear front-panel button to place one or more marks on the
waveform. Navigating between marks is as simple as pressing the Previous
(←) and Next (→) buttons on the front panel.
Every DPO7000C Series oscilloscope includes the DPOJET Essentials
jitter and eye pattern analysis software package, extending the
oscilloscope's measurement capabilities to take measurements over
contiguous clock and data cycles in a single-shot real-time acquisition. This
enables measurement of key jitter and timing analysis parameters such as
Time Interval Error and Phase Noise to help characterize possible system
timing issues. Analysis tools such as plots for time trends and histograms
quickly show how timing parameters change over time, and spectrum
analysis quickly shows the precise frequency and amplitude of jitter and
modulation sources.
Search marks
The Search button allows you to automatically search through your long
acquisition looking for user-defined events. All occurrences of the event are
highlighted with search marks and are easily navigated to, using the front-
panel Previous (←) and Next (→) buttons. Search types include edge,
glitch, width, timeout, runt, pattern, state, setup and hold, transition, and
window.
Specialized application support for serial bus debug and compliance test,
jitter and eye pattern analysis, power supply design, limit and mask testing,
DDR memory bus analysis, and wideband RF is also available.
Advanced search and mark
A 25 M point standard record length represents thousands of screens of
information. The DPO7000C Series enables you to find your event in
seconds with Advanced Search and Mark.
Search step 2: Advanced Search and Mark automatically searches through the record
and marks each event with a solid colored triangle. You can then use the Previous and
Next buttons to jump from one event to the next.
4 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Digital phosphor technology
The DPO7000C Series' digital phosphor technology provides you with fast
insight into the real operation of your device. Its fast waveform capture rate
– greater than 250,000 wfm/s – gives you a high probability of quickly
seeing the infrequent problems common in digital systems: runt pulses,
glitches, timing issues, and more.
Customized serial triggering. Visual Trigger set to find a serial data pattern of 1101 0101.
Digital phosphor technology enables greater than 250,000 wfm/s waveform capture rate
and real-time color grading on the DPO7000C Series.
Waveforms are superimposed with one another and waveform points are
color coded by frequency of occurrence. This quickly highlights the events
that occur more often over time or, in the case of infrequent anomalies,
occur less often.
With the DPO7000C Series, you can choose infinite persistence or variable
persistence, determining how long the previous waveform acquisitions stay
on-screen. This allows you to determine how often an anomaly is occurring.
Visual Trigger – Find the signal of interest
quickly
Multiple channel triggering. Visual Trigger areas can be associated with events spanning
multiple channels such as packets transmitted on two USB2.0 buses simultaneously.
By triggering only on the most important signal events, Visual Trigger can
save hours of capturing and manually searching through acquisitions. In
seconds or minutes, you can find the critical events and complete your
debug and analysis efforts. Using the Mark All Trigger Events feature, once
your Visual Trigger is set, your oscilloscope can automatically search the
entire acquired waveform for all events with the same characteristics and
mark them for you - a great time-saving feature.
Finding the right cycle of a complex bus can require hours of collecting and
sorting through thousands of acquisitions for an event of interest. Defining a
trigger that isolates the desired event speeds up debug and analysis
efforts.
Visual Trigger qualifies the Tektronix Pinpoint Triggers by scanning through
all waveform acquisitions and comparing them to on-screen areas
(geometric shapes). Up to eight areas can be created using a mouse or
touchscreen, and a variety of shapes (triangles, rectangles, hexagons, or
trapezoids) can be used to specify the desired trigger behavior. Once
shapes are created, they can be edited interactively to create ideal trigger
conditions
DDR memory bus events involve clocks, strobes and data channels as well
as multiple amplitudes and bursts of data.
Visual Trigger extends the Tektronix oscilloscope's triggering capabilities
for a wide variety of complex signals as illustrated by the examples shown
here.
www.tek.com/DPO7000
5
Datasheet
DDR memory. Visual Trigger used to isolate a rare occurrence of a write burst on a
specific bit pattern in DDR3. The trigger event is a Write DQ burst of 11000000, when the
DQ launch starts from a non-tri-state voltage value. DDR memory bus events involve
clocks, strobes and data channels as well as multiple amplitudes and bursts of data.
Trigger on the width of a burst of 10 pulses. By drawing a "Must be outside" area before
the first clock pulse and a second "Must be outside" area after the tenth pulse, as shown,
you can define a Visual Trigger setup that captures the desired burst width.
Serial triggering and analysis (optional)
On a serial bus, a single signal often includes address, control, data, and
clock information. This can make isolating events of interest difficult. The
DPO7000C Series offers a robust set of tools for debugging serial buses
with automatic trigger and decode on I2C, SPI, CAN, LIN, FlexRay,
RS-232/422/485/UART, MIL-STD-1553, and USB 2.0, and decode for MIPI
D-PHY DSI-1 and CSI-2, 8b/10b, Ethernet, and PCI Express serial buses.
Serial triggering
Trigger on packet content such as start of packet, specific addresses,
specific data content, unique identifiers, etc. on popular serial interfaces
such as I2C, SPI, CAN, LIN, FlexRay, RS-232/422/485/UART, MIL-
STD-1553, and USB 2.0.
Boolean logic trigger qualification. Boolean logic using logical OR allows the user to
simultaneously monitor each bit and capture the occurrence of an anomaly at any point
in the acquisition.
6 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Triggering on a specific OUT Token packet on a USB full-speed serial bus. A bus
waveform provides decoded packet content including Start, Sync, PID, Address, End
Point, CRC, Data values, and Stop.
Event table showing decoded serial packet data in a long acquisition.
Bus searching
Serial triggering is very useful for isolating the event of interest, but once
you’ve captured it and need to analyze the surrounding data, what do you
do? In the past, users had to manually scroll through the waveform
counting and converting bits and looking for what caused the event. With
the DPO7000C Series, you can have the oscilloscope automatically search
through the acquired data for user-defined criteria including serial packet
content. Each occurrence is highlighted by a search mark. Rapid navigation
between marks is as simple as pressing the Previous (←) and Next (→)
buttons on the front panel.
Bus display
Provides a higher-level, combined view of the individual signals (clock,
data, chip enable, etc.) that make up your bus, making it easy to identify
where packets begin and end and identifying subpacket components such
as address, data, identifier, CRC, etc.
Bus decoding
Tired of having to visually inspect the waveform to count clocks, determine
if each bit is a 1 or a 0, combine bits into bytes, and determine the hex
value? Let the oscilloscope do it for you! Once you've set up a bus, the
DPO7000C Series will decode each packet on the bus, and display the
value in hex, binary, decimal (USB only) or ASCII (USB and
Serial bus compliance test (optional)
Software packages for automated compliance test are available for
BroadR-Reach/100BASE-T1 and 1000BASE-T1 (Option BRR), MIPI D-
PHY (Option D-PHY), Ethernet 10BASE-T, 10BASE-Te, 100BASE-TX, and
1000BASE-T (Option ET3), NBASE-T and IEEE802.3bz (Option NBASE-
T), 10GBASE-T (Option XGBT2), MOST50 and MOST150 electrical
(Option MOST), and USB 2.0 (Option USB2) physical-layer devices. These
software packages enable you to conduct testing using the standard's
specified compliance tests.
RS-232/422/485/UART only) in the bus waveform.
Event table display
In addition to seeing decoded packet data on the bus waveform itself, you
can view all captured packets in a tabular view much like you would see in
a software listing. Packets are time stamped and listed consecutively with
columns for each component (Address, Data, etc.).
www.tek.com/DPO7000
7
Datasheet
Advanced analysis jitter timing and eye
diagram measurements (optional)
The optional DPOJET Advanced software package (Option DJA) offers
extended capabilities, providing a complete suite of analysis tools for
insight into jitter, timing and other signal quality issues. DPOJET Advanced
adds advanced tools such as Rj/Dj separation, eye diagram masks, and
Pass/Fail limits for conformance testing. The innovative one-touch wizard
makes setup for jitter measurements easy. DPOJET Advanced is also a
measurement framework that works with standards-specific compliance
test packages for applications such as DDR memory and USB 2.0.
USB 2.0 Automated Compliance Testing.
Power analysis (optional)
The optional power analysis software package (Option PWR) enables quick
and accurate analysis of power quality, switching loss, harmonics, magnetic
measurements, safe operating area (SOA), modulation, ripple, amplitude
and timing measurements, and slew rate (di/dt, dv/dt). Automated,
repeatable power measurements are available with a touch of a button; no
external PC or complex software setup is required. The package includes a
report generation tool to automatically create detailed reports to document
your measurement results.
Advanced analysis, jitter, eye diagram, and timing measurements.
Limit and mask testing
The standard limit test and optional mask test (Option MTM) software
packages are useful for long-term signal monitoring, characterizing signals
during design, and testing on a production line. The limit test software
compares a tested signal to a known good or "golden" version of the same
signal with user-defined vertical and horizontal tolerances. The mask test
software includes a robust set of masks for telecommunications and
computer standards for easily checking compliance to a standard.
Additionally, custom masks can be created and used for characterizing
signals. With both software packages you can tailor a test to your specific
requirements by defining test duration in number of waveforms, setting a
violation threshold that must be met before considering a test a failure,
counting hits along with statistical information, and setting actions upon
violations, test failure, and test complete. Whether specifying a limit
template or a mask, conducting pass/fail tests in search of waveform
anomalies such as glitches has never been easier.
Switching Loss measurements. Automated power measurements enable quick and
accurate analysis of common power parameters.
8 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
™
SignalVu enables detailed analysis in multiple domains.
Mask testing an OC-12 signal, capturing any violations of the mask.
Designed to make your work easier
DDR memory bus analysis (optional)
The optional DDR memory analysis software package (Option DDRA)
automatically identifies DDR1, DDR2, DDR3, LP-DDR, LP-DDR2, and
GDDR3 Reads and Writes and makes JEDEC conformance measurements
with Pass/Fail results on all edges in every Read and Write burst, perfect
for debugging and troubleshooting DDR memory buses. Also provided are
common measurements of clock, address, and control signals. Used with
DPOJET (Option DJA), Option DDRA is the fastest way to debug complex
memory signaling issues.
Large high-resolution display
The DPO7000C Series features a 12.1 in. (307 mm) XGA color display with
an integrated touch screen for seeing intricate signal details.
Dedicated front-panel controls
Per-channel vertical controls provide simple and intuitive operation. No
longer do you need to share one set of vertical controls across all four
channels.
Vector signal analysis (optional)
Connectivity
™
The optional SignalVu vector signal analysis packages (Options SVE,
USB 2.0 host ports on the front and side panels enable easy transfer of
screenshots, instrument settings, and waveform data to a USB thumb drive.
The rear panel contains a GPIB port for controlling the oscilloscope
remotely from a computer. An integrated 10/100/1000BASE-T Ethernet port
enables easy connection to networks and a Video Out port allows the
oscilloscope display to be exported to an external monitor or projector.
PS-2 ports for keyboard and mouse are included for security-conscious
applications that require the USB ports to be disabled. A standard
removable hard disk drive makes customizing settings for different users
easy and enables use in secure environments.
SVA, SVM, SVO, SVP, and SVT) easily validate wideband designs and
characterize wideband spectral events. By combining the signal analysis
engine of Tektronix real-time spectrum analyzers with the wide bandwidth
acquisition of Tektronix digital oscilloscopes, you can now evaluate
complex baseband signals directly on your oscilloscope. You get the
functionality of a vector signal analyzer, a spectrum analyzer, and the
powerful trigger capabilities of a digital oscilloscope – all in a single
package. Whether your design validation needs include wideband radar,
high data-rate satellite links, or frequency-hopping communications,
™
SignalVu vector signal analysis software can speed your time-to-insight
by showing you time-variant behavior of these wideband signals.
www.tek.com/DPO7000
9
Datasheet
®
TekVPI probe interface
Interoperability with logic analyzer
™
The TekVPI probe interface sets the standard for ease of use in probing.
TekVPI probes feature status indicators, controls and a probe menu button
right on the probe itself. This button brings up a probe menu on the
oscilloscope display with all relevant settings and controls for the probe.
The TekVPI interface enables direct attachment of a current probe without
requiring a separate power supply. TekVPI probes can be controlled
remotely through USB, GPIB, or Ethernet, enabling more versatile solutions
in ATE environments.
The Tektronix Integrated View (iView ) data display enables digital
designers to solve signal integrity challenges and effectively debug and
verify their systems more quickly and easily. This integration allows
designers to view time-correlated digital and analog data in the same
display windows, and isolate the analog characteristics of the digital signals
that are causing system failures. No user calibration is required. And, once
set up, the iView feature is completely automated.
Remote operation and extended analysis
®
MyScope custom control window
There are many ways to connect to your DPO7000C Series oscilloscope to
conduct extended analysis. The first makes use of the Windows Remote
Desktop capability – connect directly to your oscilloscope and operate the
user interface remotely through the built-in Remote Desktop. A second way
Easily create your own personalized "toolbox" of oscilloscope features in a
matter of minutes using a simple, visual, drag-and-drop process. Once
created, these custom control windows are easily accessed through a
dedicated MyScope menu selection on the oscilloscope. This is ideal in a
shared resource environment where each person can have their own
custom control interface suited to their particular use. MyScope control
windows benefit all oscilloscope users, eliminating the ramp-up time that
many face when returning to the lab after not using an oscilloscope for a
while, and enabling power users to be far more efficient.
®
to connect is through Tektronix OpenChoice software which makes use of
the fast embedded bus, transferring waveform data directly from acquisition
to analysis applications on the Windows desktop at much faster speeds
than conventional GPIB transfers. Industry-standard protocols, such as
™
TekVISA interface and ActiveX controls are included for using and
enhancing Windows applications for data analysis and documentation. IVI-
COM instrument drivers are included to enable easy communication with
the oscilloscope using GPIB, serial data, and LAN connections from
programs running on the instrument or an external PC. Or, use the
Software Developer's Kit (SDK) to help create custom software to automate
multistep processes in waveform collection and analysis with Visual BASIC,
C, C++, MATLAB, LabVIEW, LabWindows/CVI, and other common
Application Development Environments (ADE).
MyScope custom control windows are created with a simple drag-and-drop process
enabling each user to have a unique interface.
Floating licenses
Floating licenses offer an alternative method to manage your Tektronix
asset. Floating licenses allow license-key enabled options to be easily
moved among all your MSO/DPO5000, DPO7000, and DPO/DSA/
MSO70000 Series of Tektronix oscilloscopes. Floating licenses are
available for many license-key enabled options. To order a floating version
of an option license add “DPOFL-“ prefix to the option name. (e.g. DPOFL-
ET3)
Capture data into Microsoft Excel using the unique Excel toolbar, and create custom
reports using the Word toolbar.
Check www.tek.com for additional information about floating license
options.
10 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Specifications
All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.
Model overview
DPO7054C
DPO7104C
DPO7254C
DPO7354C
Input Channels
4
Bandwidth
500 MHz
1 GHz
300 ps
200 ps
2.5 GHz
160 ps
100 ps
3.5 GHz
115 ps
95 ps
Rise Time 10% to 90% (Typical)
Rise Time 20% to 80% (Typical)
DC Gain Accuracy
460 ps
310 ps
±1% with offset/position set to 0
Bandwidth Limits
Depending on instrument model: 3.0 GHz, 2.5 GHz, 2 GHz, 1 GHz, 500 MHz, 250 MHz, and 20 MHz
Effective Number of Bits (Typical, sine 6.8 bits
wave input at instrument bandwidth,
50 mV/div, 50 Ω Input Impedance,
maximum sample rate, 20k point
record length)
6.7 bits
5.6 bits
5.6 bits
Random Noise (RMS, typical, sample mode, full BW, maximum sample rate, 50 Ω)
Step Gain
1 V
19.4 mV
10.5 mV
4.72 mV
2.64 mV
1.07 mV
0.487 mV
0.273 mV
0.173 mV
0.112 mV
0.087 mV
19.72 mV
10.89 mV
4.69 mV
24.48 mV
14.91 mV
6.70 mV
26.28 mV
16.46 mV
7.26 mV
4.49 mV
1.65mV
500 mV
200 mV
100 mV
50 mV
20 mV
10 mV
5 mV
2.70 mV
4.11 mV
1.10 mV
1.53 mV
0.484 mV
0.279 mV
0.191 mV
0.121 mV
0.090 mV
0.678 mV
0.414 mV
0.285 mV
0.142 mV
0.098 mV
0.735 mV
0.458 mV
0.303 mV
0.148 mV
0.100 mV
2 mV
1 mV
DPO7054C
20 GS/s
10 GS/s
5 GS/s
DPO7104C
20 GS/s
10 GS/s
5 GS/s
DPO7104C with Option 2SR DPO7254C/DPO7354C
Maximum Sample Rate (1 ch)
Maximum Sample Rate (2 ch)
Maximum Sample Rate (3-4 ch)
40 GS/s
20 GS/s
10 GS/s
40 GS/s
20 GS/s
10 GS/s
Maximum Equivalent Time Sampling 4 TS/s
Rate
Maximum Record Length with
Standard Configuration
125 M (1 ch), 50 M (2 ch), 25 M (3-4 ch)
Maximum Record Length with Option 250 M (1 ch), 125 M (2 ch), 50 M (3-4 ch)
5RL
Maximum Record Length with Option
10RL (sample rates ≥2.5 GS/s)
—
—
—
500 M (1 ch)
250 M (2 ch)
125 M (3-4 ch)
Maximum Duration at Highest Real- 1-2 ms with standard record length, up to 10 ms with optional record length
time Sample Rate (1 ch)
Time Base Range
1.25 ps/div to 8 Ms/div
500 fs
1.25 ps/div to 8 Ms/div
500 fs
1.25 ps/div to 8.19 Ms/div
250 fs
1.25 ps/div to 8.19 Ms/div
250 fs
Time Resolution (in ET/IT mode)
www.tek.com/DPO7000 11
Datasheet
Vertical system – Analog channels
Input impedance
Input coupling
Input sensitivity
1 MΩ ±1% with 13 pF ±2 pF, 50 Ω ±1%
AC, DC, GND
1 MΩ: 1 mV/div to 10 V/div
50 Ω: 1 mV/div to 1 V/div
Vertical resolution
8 bit (>11 bit with Hi Res)
Delay between any two channels, ≤100 ps (50 Ω, DC coupling and equal V/div at or above 10 mV/div)
typical
Channel-to-Channel isolation
(Any two channels at equal Vertical Scale settings) (Typical)
≥100:1 at ≤100 MHz
≥30:1 between 100 MHz and 2.5 GHz
≥20:1 between 2.5 GHz and 3.5 GHz
Max input voltage 1 MΩ
Max input voltage 50 Ω
Offset range
±150 V, derate at 20 dB/decade to 9 VRMS above 200 kHz
5 VRMS, with peaks ≤ ±24 V
1 mV/div to 50 mV/div: ±1 V
50.5 mV/div to 99.5 mV/div: ±(1.5 V – 10 divisions)
100 mV/div to 500 mV/div: ±10 V
505 mV/div to 995 mV/div: ±(15 V – 10 divisions)
1 V/div to 5 V/div: ±100 V
5.05 V/div to 10 V/div: ±(150 V – 10 divisions)
Offset accuracy
Position range
1 mV/div to 9.95 mV/div: ±0.2% × (offset – position) ±0.1 div ±1.5 mV
10 mV/div to 99.5 mV/div: ±0.35% × (offset – position) ±0.1 div ±1.5 mV
100 mV/div to 1 V/div: ±0.35% × (offset – position) ±0.1 div ±15 mV
1.01 V/div to 10 V/div: ±0.25% × (offset – position) ±0.1 div ±150 mV
±5 divisions
Horizontal system
Time base delay time range
-10 divisions to 1000 s
Channel-to-channel deskew range ±75 ns
Delta time measurement accuracy ((0.06 / sample rate) + (2.5 ppm × Reading)) RMS
Trigger jitter (RMS)
1.5 psRMS with enhanced triggering OFF
<100 fsRMS with enhanced triggering ON
12 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Horizontal system
Timebase stability (aperture
uncertainty), typical
<1 psRMS (<2 psPeak) for record duration <10 μs (typical)
<2.5 psRMS for record duration <30 ms
<65 parts/trillion for record durations <10 s
Time base accuracy
±2.5 ppm + aging <1 ppm per year
Acquisition system
Acquisition modes
Sample
Acquires and displays sampled values
Peak detect
Averaging
Envelope
Captures and displays narrow glitches at all real-time sampling rates. Glitch widths: 1 ns at ≤10 GS/s
From 2 to 10,000 waveforms can be included in an average waveform
From 1 to 2×109 waveforms included in min-max envelope
Hi-Res
Real-time boxcar averaging reduces random noise and increases resolution
Roll mode
Scrolls sequential waveform points across the display in a right-to-left rolling motion at sweep speeds slower than 50 ms/div.
Works at sample rates up to 10 MS/s with a maximum record length of 40 MS
®
®
FastAcq
FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events, capturing >250,000 wfms/s on
all 4 channels simultaneously
Waveform database
Accumulates waveform data providing a three-dimensional array of amplitude, time, and counts
™
FastFrame
Acquisition memory divided into segments; maximum trigger rate >310,000 waveforms per second. Time of arrival recorded with
each event. Frame finder tool helps to visually identify transients
®
Pinpoint trigger system
Trigger sensitivity
Internal DC coupled
0.7 div from DC to 50 MHz, increasing to 1.2 div at rated analog bandwidth (typical), up to 2.5 GHz. 2.5 div at 3.5 GHz
250 mV from DC to 50 MHz, increasing to 350 mV at 250 MHz (typical)
Aux input (external trigger)
1 MΩ
Trigger delay by time
Trigger delay by events
Main trigger modes
Enhanced triggering
3.2 ns to 3,000,000 s
1 to 2,000,000,000 events
Auto, Normal, and Single
Enhanced triggering corrects the difference in timing between the trigger path and the acquired data path (supports all Pinpoint
trigger types on both A- and B-Events except pattern trigger); Default On (user-selectable); Not available in FastAcq mode.
Trigger sequences
Main, Delayed by Time, Delayed by Events, Reset by Time, Reset by State, Reset by Transition, B Event Scan. All sequences can
include separate horizontal delay after the trigger event to position the acquisition window in time.
Communications-related triggers
Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated positive or negative
one, zero pulse form, or eye patterns as applicable to the standard. Requires Option MTM.
Video trigger formats and field
rates
Triggers from negative sync composite video, field 1 or field 2 for interlaced systems, any field, specific line, or any line for
interlaced or noninterlaced systems. Supported systems include NTSC, PAL, SECAM, and HDTV 1080/24sF, 1080p/25, 1080i/50,
1080i/60, 1080p/24, 720p/60, 480p/60
Serial pattern trigger
NRZ-Encoded Data
DPO7254C and DPO7354C only, requires Opt. ST1G. Up to 64 bit serial word recognizer, bits specified in binary (high, low, don't
care) or hex format. Trigger on NRZ-encoded data up to 1.25 GBaud.
www.tek.com/DPO7000 13
Datasheet
®
Pinpoint trigger system
Clock recovery system
(DPO7254C and DPO7354C only, requires Opt. ST1G)
Clock recovery phase locked Fixed at FBaud/500
loop bandwidth
Clock recovery frequency
range
1.5 MBaud to 1.25 GBaud
Clock recovery jitter (RMS)
20 psRMS + 1.25% Unit Interval RMS for PRBS data patterns
20 psRMS + 1.25% Unit Interval RMS for repeating "0011” data pattern
±5% of requested baud rate (typical)
Clock recovery tracking/
acquisition range
Minimum signal amplitude
needed for clock recovery
1 divp-p up to 1.25 Gbaud
Trigger level range
Any channel
Auxiliary input
Line
±12 divisions from center of screen
TekVPI interface; ±5 V (50 Ω); 150 V, derate at 20 dB/decade to 9 VRMS above 200 kHz (1 MΩ)
Fixed at 0 V
Trigger coupling
DC
AC (attenuates <60 Hz)
HF Rej (attenuates >30 kHz)
LF Rej (attenuates <80 kHz)
Noise Reject (reduces sensitivity)
Trigger holdoff range
Trigger types
Edge
250 ns min to 100 s
A Event and Delayed B Event trigger types: edge, glitch, width, runt, timeout, transition time, logic pattern, logic state, setup/hold,
window - all except Edge, Pattern, and State can be Logic State qualified by up to two channels.
Positive, negative, or either slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject,
and LF reject.
Glitch
Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width is 170 ps (typical) with rearm time of
250 ps (for DPO7254C or DPO7354C).
Width
Runt
Trigger on width of positive or negative pulse either within or outside selectable limits (225 ps to 10 s).
Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Event can be
time- or logic-qualified.
Window
Trigger on an event that enters or exits a window defined by two user-adjustable thresholds. Event can be time or logic qualified.
Trigger on an event which remains high, low, or either, for a specified time period (300 ps to 1 s).
Timeout
Transition
Setup/Hold
Logic Pattern
Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either.
Trigger on violations of both setup time and hold time between clock and data present on any two input channels.
Trigger when pattern goes false or stays true for specified period of time (300 ps to 1 s). Pattern (AND, OR, NAND, NOR) specified
for all analog input channels defined as high, low, or don’t care.
Logic State
Parallel Bus
Video
Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge.
Trigger on specified data value on defined parallel bus.
Trigger on all lines, specific line number, odd, even, or all fields on NTSC, PAL, SECAM, and HDTV 480p/60, 576p/50, 875i/60,
720p/30, 720p/50, 720p/60, 1080/24sF, 1080i/50, 1080p/25, 1080i/60, 1080p/24, 1080p/25, 1080p/50, 1080p/60, Bi-level, Tri-
level.
Visual Trigger
Trigger on up to 8 user-specified areas, including rectangle, triangle, trapezoid, hexagon, and user-specified shapes on any of the
analog channels.
14 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
®
Pinpoint trigger system
Optional trigger types
Serial Pattern
Captures serial data stream with built-in clock recovery for NRZ standards up to 1.25 Gb/s. Extended with pattern lock triggering to
capture repeated acquisitions of long serial data patterns. Provided as part of Opt. ST1G.
Comm
I2C
Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded signals. Provided as part of Option MTM.
Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data (1-5 bytes), or Address and Data on I2C buses up
to 10 Mb/s. Provided as part of Opt. SR-EMBD.
SPI
Trigger on Slave Select, Idle Time, or Data (1-6 words) on SPI buses up to 10 Mb/s. Provided as part of Opt. SR-EMBD.
CAN
Trigger on Start of Frame, Frame Type (Data, Remote, Error, or Overload), Identifier, Data, Identifier and Data, End of Frame,
Missing Ack, Bit Stuff Error or CRC Error on CAN buses up to 1 Mb/s. Provided as part of Opt. SR-AUTO.
LIN
Trigger on Sync, Identifier, Data, Ident and Data, Wakeup Frame, Sleep Frame, and Error on LIN buses up to 1 Mb/s. Provided as
part of Opt. SR-AUTO.
FlexRay
Trigger on Indicator Bits (Normal, Payload, Null, Sync, Startup), Cycle Count, Header Fields (Indicator Bits, Identifier, Payload
Length, Header CRC, and Cycle Count), Identifier, Data, Identifier and Data, End Of Frame, and Error on FlexRay buses up to
10 Mb/s. Provided as part of Opt. SR-AUTO.
MIL-STD-1553B
Trigger on Sync, Command Word, Status Word, Data Word, Idle Time, and Error on MIL-STD-1553 buses up to 1 Mb/s. Provided
as part of Opt. SR-AERO.
RS-232/422/485/UART
USB 2.0 Low speed
Trigger on Start Bit, End of Packet, Data (1-5 words), and Parity Error on RS-232 buses up to 10 Mb/s. Provided as part of Opt.
SR-COMP.
Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special
Packet, Error. Provided as part of Opt. SR-USB.
Token Packet Trigger – Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any, OUT, IN, and SETUP token
types. Address can be further specified to trigger on ≤, <, =, >, ≥, != a particular value, or inside or outside a range. Frame number
can be specified for SOF token using Binary, Hex, Unsigned Decimal, and Don't Care digits.
Data Packet Trigger – Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, != a particular data
value, or inside or outside of a range.
Handshake Packet Trigger – Any handshake type, ACK, NAK, STALL.
Special Packet Trigger – Any special type, Reserved.
Error Trigger – PID Check, CRC5 or CRC16, Bit Stuffing.
USB 2.0 Full speed
Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special
Packet, Error. Provided as part of Opt. SR-USB.
Token Packet Trigger – Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any, OUT, IN, and SETUP token
types. Address can be further specified to trigger on ≤, <, =, >, ≥, != a particular value, or inside or outside a range. Frame number
can be specified for SOF token using Binary, Hex, Unsigned Decimal, and Don't Care digits.
Data Packet Trigger – Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, != a particular data
value, or inside or outside a range.
Handshake Packet Trigger – Any handshake type, ACK, NAK, STALL.
Special Packet Trigger – Any special type, PRE, Reserved.
Error Trigger – PID Check, CRC5 or CRC16, Bit Stuffing.
No protocol-level triggering. Provided as part of Opt. SR-USB.
USB 2.0 High speed
USB 2.0 High speed decoding and search only available on ≥1 GHz models.
www.tek.com/DPO7000 15
Datasheet
Waveform analysis
Search and Mark Events
Use Advanced Search and Mark to automatically mark events and document waveforms. Search positive/negative slopes or both,
glitches, runts, pulse widths, transition rate, setup and hold, timeout, windows, or find any logic or state pattern, up to 8 different
event types on any of the 4 analog channels. Search DDR Read or Write bursts with Opt. DDRA.
When an event of interest is found with a hardware trigger, other similar events can be found using "Mark All Trigger Events in
Record" in the Pinpoint trigger control windows.
The Event table summarizes all found events. All events are time stamped in reference to trigger position. You can choose to stop
acquisitions when an event is found.
Waveform measurements
Cursors
Waveform and Screen
Automatic measurements
Measurement Statistics
Reference Levels
Gating
53, of which 8 can be displayed on-screen at any one time
Mean, Minimum, Maximum, Standard Deviation
User-definable reference levels for automatic measurements can be specified in either percent or units
Isolate the specific occurrence within an acquisition to take measurements on, using either screen or waveform cursors
Amplitude related
Amplitude, High, Low, Maximum, Minimum, Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative
Overshoot
Time related
Rise Time, Fall Time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay
Area, Cycle Area, Phase, Burst Width
Combination
Histogram related
Waveform Count, Hits in Box, Peak Hits, Median, Maximum, Minimum, Peak-to-Peak, Mean (μ), Standard Deviation (sigma), μ
+1sigma, μ+2sigma, μ+3sigma
Eye-pattern related
Extinction Ratio (absolute, %, dB), Eye Height, Eye Width, Eye Top, Eye Base, Crossing %, Jitter (p-p, RMS, 6sigma), Noise (p-p,
RMS), Signal/Noise Ratio, Cycle Distortion, Q-Factor
Waveform Histograms
A waveform histogram provides an array of data values representing the total number of hits inside a user-defined region of the
display. A waveform histogram is both a visual graph of the hit distribution and a numeric array of values that can be measured.
Sources – Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math 1, Math 2, Math 3, Math 4
Types – Vertical, Horizontal
Waveform processing/math
Number of Math Waveforms
Arithmetic
Up to 4
Add, Subtract, Multiply, Divide Waveforms and Scalars
Algebraic expressions
Define extensive algebraic expressions including waveforms, scalars, user-adjustable variables, and results of parametric
measurements. Perform math on math using complex equations. e.g. (Integral (CH1 – Mean(CH1)) × 1.414 × VAR1)
Math functions
Average, Invert, Integrate, Differentiate, Square Root, Exponential, Log 10, Log e, Abs, Ceiling, Floor, Min, Max, Sin, Cos, Tan,
ASin, ACos, ATan, Sinh, Cosh, Tanh
Relational
Boolean result of comparison >, <, ≥, ≤, ==, !=
Frequency domain functions Spectral Magnitude and Phase, Real and Imaginary Spectra
FFT vertical units
Magnitude: Linear, dB, dBm Phase: Degrees, radians, group delay
FFT window functions
Waveform definition
Filtering function
Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential
As an arbitrary math expression
User-definable filters. Users specify a file containing the coefficients of the filter. Several example filter files are provided
Customized Functions using An interface is provided to allow users to create their own custom math functions in MATLAB or Visual Studio
Math Plug-in Interface
Mask function
Generates a Waveform Database pixel map from a sample waveform. Sample count can be defined
16 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Software
IVI Driver
Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI,
Microsoft .NET and MATLAB. IVI-COM standard
LXI Class C Web Interface
Connect to the DPO7000C Series through a standard web browser by simply entering the oscilloscope’s IP address in the address
bar of the browser. The web interface enables viewing of instrument status and configuration, and status and modification of
network settings. All web interaction conforms to LXI Class C specification
Display system
Display type
307.3 mm (12.1 in.) liquid-crystal active-matrix color display
Display resolution
Waveform styles
Color palettes
1024 horizontal × 768 vertical pixels (XGA)
Vectors, Dots, Variable Persistence, Infinite Persistence
Normal, Green, Gray, Temperature, Spectral, and User-defined
Format
YT, XY
10
Horizontal divisions
Vertical divisions
10
Computer system and peripherals
Operating system
CPU
Microsoft Windows 10 Enterprise IoT Edition
Intel i7-2600 processor, quad core, 3.4 GHz
8 GB
System memory
Solid state drive
CD/DVD drive
Mouse
Removable, 512 GB capacity
Front-panel CD-R/W, DVD-R drive
Optical wheel mouse, USB interface
Order 119-7083-xx for small keyboard; USB interface and hub
Keyboard
Input/Output ports
USB 2.0 High-speed Host Ports
Supports USB mass storage devices, printers, keyboard, and mouse. Ports on front and side panels of the instrument. Can be
disabled
USB 3.0 SuperSpeed Host Ports
GPIB interface
Supports USB mass storage devices, printers, keyboard, and mouse. Ports on side panel of the instrument. Can be disabled
Rear panel. IEEE 488.2 standard
LAN port
RJ-45 connector, supports 10BASE-T, 100BASE-T, and 1000BASE-T
Video out port
DVI-I and VGA connectors, connect to show the oscilloscope display on an external monitor or projector. Support for extended
desktop and clone mode
Audio input/output
Miniature phone jacks for stereo microphone input and stereo line output
www.tek.com/DPO7000 17
Datasheet
Input/Output ports
Keyboard port
PS/2 compatible
Mouse port
PS/2 compatible
Auxiliary input
Front panel. See trigger specifications
Auxiliary Out (Software
switchable)
Trigger Out: A TTL compatible pulse when the oscilloscope triggers
Time Base Reference Out: A TTL compatible output of internal 10 MHz reference oscillator
External time base reference in
Analog Signal Output
Time base system can phase lock to an external 10 MHz reference (10 MHz ±1%)
BNC connector provides a buffered version of the Ch3 signal. 50 mV/div ±20% into a 1 MΩ load, 25 mV/div ±20% into a 50 Ω
load. Bandwidth is 100 MHz into a 50 Ω load
Probe compensator output
Front-panel pins
Amplitude: 1 V ±20% into a ≥50 Ω load
Frequency: 1 kHz ±5%
Recovered Clock (DPO7254C and (Enabled by Opt. ST1G.) BNC connector, ≤1.25 Gb/s, output swing ≥130 mVp-p into 50 Ω
DPO7354C only)
Recovered Data (DPO7254C and
DPO7354C only)
(Enabled by Opt. ST1G.) BNC connector, ≤1.25 Gb/s, output swing 200 mV into 50 Ω
LXI web interface (LAN eXtensions Class: LXI Class C Version: 1.3
for instrumentation)
Power source
Power Source
100 to 240 V ±10%, 47 to 63 Hz, <550 W
115 VRMS ±10%, 360 to 440 Hz, <500 VA
Physical characteristics
Dimensions
mm
292
451
265
in.
Height
Width
Depth
11.48
17.75
10.44
Rackmount dimensions
mm
331
479
in.
Height
Width
12.25
18.85
9.12
Depth (from rack mounting ear to back of 231.75
instrument)
Weight
kg
lb.
Net
15
32
Shipping
28.9
63.75
18 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Physical characteristics
Rackmount weight
kg
lb.
Net
Kit
17.4
2.5
37.5
5.5
Cooling – Required clearance
mm
0
in.
0
Top
Bottom
Left Side
Right Side
Front
0
0
76
0
3
0
0
0
Rear
0
0
Environmental
Temperature
Operating
+5 °C to +45 °C, with noncondensing conditions
Nonoperating
–40 °C to +71 °C, with 15 °C/hour maximum gradient, without CD/DVD media installed in disk drive
Humidity
Operating
8% to 80% relative humidity (RH) with a maximum wet bulb temperature of 29 °C at or below +45 °C, noncondensing. Upper limit
derated to 30% RH at +45 °C
Nonoperating
5% to 90% relative humidity (RH) with a maximum wet bulb temperature of 29 °C at or below +60 °C, noncondensing. Upper limit
derated to 20% RH at +60 °C
Altitude
Operating
Nonoperating
3,000 m (9,843 ft.)
12,192 m (40,000 ft.)
Regulatory
Electromagnetic compatibility 2004/108/EC
Certifications UL61010-1; CSA61010-1, EN61010-1; IEC 61010-1
www.tek.com/DPO7000 19
Datasheet
Ordering information
DPO7000C models
DPO7054C
DPO7104C
DPO7254C
DPO7354C
500 MHz, 5/10/20 GS/s (4/2/1 ch), 25 M record length, 4-channel digital phosphor oscilloscope
1 GHz, 5/10/20 GS/s (4/2/1 ch), 25 M record length, 4-channel digital phosphor oscilloscope
2.5 GHz, 10/20/40 GS/s (4/2/1 ch), 25 M record length, 4-channel digital phosphor oscilloscope
3.5 GHz, 10/20/40 GS/s (4/2/1 ch), 25 M record length, 4-channel digital phosphor oscilloscope
Standard accessories
P6139B
One passive voltage probe per analog channel (500 MHz, 10X, 8 pF)
—
Front cover
071-298x-xx
User Manual (please specify language when ordering)
—
—
—
—
—
—
—
—
GPIB programmer's reference PDF file
Performance verification procedure PDF file
Advanced Search and Mark, DPOJET Essentials, Visual Trigger and Search, and Limit Test all included standard
Accessory pouch
Mouse
Calibration Certificate documenting measurement traceability to National Metrology Institute(s), Z 540-1 Compliance and ISO9001
Power Cord (please specify power plug option when ordering)
One-year warranty
Instrument options
Record length options
Opt. 5RL
250 M max, 50 M/ch
Opt. 10RL
DPO7254C and DPO7354C only, 500 M max, 125 M/ch
Sample rate options
Opt. 2SR
Double maximum real-time sample rate to 40/20/10 GS/s on 1/2/4 ch (DPO7104C only)
Storage options
Opt. SSD
Solid State Drive assembly; customer-installable removable drive with Microsoft Windows 10 OS, TekScope, and applications
software installed
20 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Advanced analysis options
Option
Description
Opt. BRR
BroadR-Reach/100BASE-T1 and 1000BASE-T1 Compliance Testing (Requires TF-GBE-BTP and TF-
BRR-CFD Test Fixtures) (For models of bandwidth ≥1 GHz only)
Opt. DDRA
Opt. DJA
DDR Memory Bus Analysis (Requires Opt. DJA) (For models of bandwidth ≥1 GHz only)
Jitter and Eye Analysis Tools – Advanced (DPOJET)
Opt. DJAN
Opt. D-PHY
DPOJET Noise, jitter, and eye analysis tools (Requires Opt. DJA)
®
MIPI D-PHY Essentials – Transmitter Debug, Characterization, and Compliance Test Solution (Requires
Opt. DJA) (For models of bandwidth ≥2.5 GHz only)
Opt. ET3
Ethernet Compliance Test Software (Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture)
Electrical Compliance and Debug Test Solution for MOST50 and MOST150 (Requires Opt. DJA)
Opt. MOST
Opt. MTM
Mask Testing for ITU-T, ANSI T1.102, Ethernet, SONET/SDH, Fibre Channel, USB 2.0, IEEE 1394b,
Rapid I/O, OIF, CPRI, and Serial Video; (includes hardware clock recovery on DPO7254C/DPO7354C)
Opt. NBASE-T
TekExpress Automated NBASE-T and IEEE802.3bz (2.5G and 5G) Compliance Test Software (Requires
TF-XGbt Test Fixture) (For models of bandwidth ≥2.5 GHz only)
Opt. PWR
Power Measurement and Analysis Software
Opt. SR-AERO
Aerospace Serial Triggering and Analysis (MIL-STD-1553). Enables triggering on packet-level information
on MIL-STD-1553 buses as well as analytical tools such as bus views, packet decoding, search tools, and
packet decode tables with time stamp information
Opt. SR-AUTO
Opt. SR-COMP
Opt. SR-DPHY
Opt. SR-EMBD
Opt. SR-ENET
Opt. SR-PCIE
Automotive Serial Triggering and Analysis (CAN/LIN/FlexRay). Enables triggering on packet-level
information on CAN, LIN, and FlexRay buses as well as analytical tools such as digital views of the signal,
bus views, packet decoding, search tools, and packet decode tables with time stamp information
Computer Serial Triggering and Analysis (RS-232/422/485/UART). Enables triggering on packet-level
information on RS-232/422/485/UART buses as well as analytical tools such as digital views of the signal,
bus views, packet decoding, search tools, and packet decode tables with time stamp information
®
MIPI D-PHY Serial Analysis. Enables analysis of MIPI DSI-1 and CSI-2 buses with analytical tools such
as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with
time stamp information
Embedded Serial Triggering and Analysis (I2C, SPI). Enables triggering on packet-level information on I2C
and 2-wire and 3-wire SPI buses as well as analytical tools such as digital views of the signal, bus views,
packet decoding, search tools, and packet decode tables with time stamp information
Ethernet Serial Analysis (10BASE-T, 100BASE-TX). Enables analysis of Ethernet buses as well as
analytical tools such as bus views, packet decoding, search tools, and packet decode tables with time
stamp information
PCI Express Serial Analysis. Enables analysis of PCI Express buses with analytical tools such as digital
views of the signal, bus views, packet decoding, search tools, and packet decode tables with time stamp
information (For models of bandwidth ≥1 GHz only) (Due to large volumes of data, use of standard high-
capacity hard drive rather than the smaller SSD is recommended.)
Opt. SR-USB
USB 2.0 Serial Triggering and Analysis (LS, FS, HS). Enables triggering on packet-level content for low-
speed and full-speed USB serial buses. Also enables analytical tools such as bus views, packet decoding,
search tools, and packet decode tables with time stamp information for low-speed, full-speed, and high-
speed USB serial buses. USB High Speed supported only on ≥1 GHz models
Opt. SR-810B
Opt. ST1G
8b/10b Serial Analysis. Enables analysis of 8b/10b buses with analytical tools such as digital views of the
signal, bus views, packet decoding, search tools, and packet decode tables with time stamp information
64-bit NRZ Serial Trigger and 8b/10b Serial Protocol Decode (includes Opt. SR-810B) (For models of
bandwidth ≥2.5 GHz only)
Opt. SVA
Opt. SVE
Opt. SVM
Opt. SVO
Opt. SVP
Opt. SVT
AM/FM/PM Audio Signal Analysis (Requires Opt. SVE)
®
SignalVu Essentials – Vector Signal Analysis Software
®
SignalVu General Purpose Modulation Analysis (Requires Opt. SVE)
®
SignalVu Flexible OFDM Analysis (Requires Opt. SVE)
®
SignalVu Advanced Signal Analysis (including pulse measurements) (Requires Opt. SVE)
®
SignalVu Frequency and Phase Settling Time Measurements (Requires Opt. SVE)
www.tek.com/DPO7000 21
Datasheet
Option
Description
Opt. SV23
WLAN 802.11a/b/g measurement application (Requires Opt. SVE) (For models of bandwidth ≥2.5 GHz
only)
Opt. SV24
WLAN 802.11n measurement application (Requires Opt. SVE and SV23) (For models of bandwidth
≥2.5 GHz only)
®
Opt. SV26
Opt. SV27
SignalVu APCO P25 measurements (Requires Opt. SVE)
®
SignalVu Bluetooth Basic LE TX SIG measurements (Requires Opt. SVE) (For models of bandwidth
≥2.5 GHz only)
®
Opt. SV28
Opt. USB2
SignalVu LTE Downlink RF measurements (Requires Opt. SVE) (For models of bandwidth ≥1 GHz only)
USB 2.0 Automated Compliance Test Application (Requires TDSUSBF (USB Test Fixture). ≥2 GHz
bandwidth required for high-speed USB)
Opt. USBPWR
Opt. XGBT2
Automated compliance test solution for USB power adapters
TekExpress Automated 10GBASE-T Compliance Test Software (Requires TF-XGbt Test Fixture) (For
DPO7354C model only)
TekExpress application framework
options
Option
Description
®
TEKEXP
TekExpress Automation Framework
Opt. D-PHYTX
D-PHY Automated Solution (Requires Opt. DJA) (For models of bandwidth ≥2.5 GHz only)
Bundle Options
These bundled items must be purchased at the same time as the instrument purchase.
Option
Description
Opt. PS2
Opt. PS3
Power Solution Bundle: DPOPWR, THDP0200, TCP0030A, 067-1686-xx (Deskew Fixture)
Power Solution Bundle: DPOPWR, TMDP0200, TCP0020, 067-1686-xx (Deskew Fixture)
Floating license options
Floating licenses offer an alternative method to manage your Tektronix asset. Floating licenses allow license-key enabled options to be easily moved among all your MSO/
DPO5000, DPO7000, and DPO/DSA/MSO70000 Series of Tektronix oscilloscopes. Floating licenses are available for the following license-key enabled options.
Check http://www.tek.com/products/oscilloscopes/floating-licenses for additional information about floating license options.
Option
Description
DPOFL-BRR
BroadR-Reach/100BASE-T1 and 1000BASE-T1 Compliance Testing (Requires TF-GBE-BTP and TF-BRR-CFD Test Fixtures)
(For models of bandwidth ≥1 GHz only)
DPOFL-DDRA
DPOFL-DJA
DDR Memory Bus Analysis (Requires Opt. DJA) (For models of bandwidth ≥1 GHz only)
Jitter and Eye Analysis Tools – Advanced (DPOJET)
DPOFL-DJAN
DPOFL-D-PHY
DPOJET Noise, jitter, and eye analysis tools (Requires Opt. DJA)
®
MIPI D-PHY Transmitter Debug, Characterization and Compliance Test Solution (Requires Opt. DJA) (For models of bandwidth
≥2.5 GHz only)
DPOFL-ET3
DPOFL-MOST
DPOFL-MTM
Ethernet Compliance Testing (Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture)
Electrical Compliance and Debug Test Solution for MOST50 and MOST150 (Requires Opt. DJA)
Mask Testing for ITU-T, ANSI T1.102, Ethernet, SONET/SDH, Fibre Channel, USB 2.0, IEEE 1394b, Rapid I/O, OIF, CPRI, and
Serial Video; (includes hardware clock recovery on DPO7254C/DPO7354C)
DPOFL-NBASE-T
TekExpress Automated NBASE-T and IEEE802.3bz (2.5G and 5G) Compliance Test Software (Requires TF-XGbt Test Fixture)
(For models of bandwidth ≥2.5 GHz only)
DPOFL-PWR
Power Measurement and Analysis
DPOFL-SR-AERO
Aerospace Serial Triggering and Analysis (MIL-STD-1553). Enables triggering on packet-level information on MIL-
STD-1553 buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding
DPOFL-SR-AUTO
DPOFL-SR-COMP
Automotive Serial Triggering and Analysis (CAN/LIN/FlexRay). Enables triggering on packet-level information on CAN, LIN, and
FlexRay buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding
Computer Serial Triggering and Analysis (RS-232/422/485/UART). Enables triggering on packet-level information on
RS-232/422/485/UART buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding
22 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
Option
Description
®
DPOFL-SR-DPHY
MIPI D-PHY Serial Analysis. Enables analysis of MIPI DSI-1 and CSI-2 buses with analytical tools such as digital views of the
signal, bus views, and packet decoding
DPOFL-SR-EMBD
DPOFL-SR-ENET
DPOFL-SR-PCIE
Embedded Serial Triggering and Analysis (I2C, SPI). Enables triggering on packet-level information on I2C and SPI buses as well
as analytical tools such as digital views of the signal, bus views, and packet decoding
Ethernet Serial Analysis (10BASE-T and 100BASE-TX) Ethernet Serial Analysis. Enables analysis of Ethernet buses with
analytical tools such as digital views of the signal, bus views, and packet decoding
PCI Express Serial Analysis. Enables analysis of PCI Express buses with analytical tools such as digital views of the signal, bus
views, and packet decoding (For models of bandwidth ≥1 GHz only) (Due to large volumes of data, use of standard high-capacity
hard drive rather than the smaller SSD is recommended)
DPOFL-SR-USB
DPOFL-SR-810B
USB 2.0 Serial Triggering and Analysis (LS, FS, HS). Enables triggering on packet-level content for low-speed and full-speed
USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, and packet decoding for low-speed,
full-speed, and high-speed USB serial buses. USB High Speed supported only on ≥1 GHz models
8b/10b Serial Analysis. Enables analysis of 8b/10b buses with analytical tools such as digital views of the signal, bus views, and
packet decoding
DPOFL- ST1G
DPOFL-SVA
DPOFL-SVE
DPOFL-SVM
DPOFL-SVO
DPOFL-SVP
DPOFL-SVT
DPOFL-SV23
DPOFL-SV24
DPOFL-SV26
DPOFL-SV27
DPOFL-SV28
DPOFL-USB2
64-bit NRZ Serial Trigger and 8b/10b Serial Protocol Decode (includes Opt. SR-810B) (For models of bandwidth ≥2.5 GHz only)
®
SignalVu AM/FM/PM Audio Signal Analysis (Requires Opt. SVE)
®
SignalVu Essentials – Vector Signal Analysis Software
®
SignalVu General Purpose Modulation Analysis (Requires Opt. SVE)
®
SignalVu Flexible OFDM Analysis (Requires Opt. SVE)
®
SignalVu Advanced Signal Analysis (including pulse measurements) (Requires Opt. SVE)
®
SignalVu Frequency and Phase Settling Time Measurements (Requires Opt. SVE)
WLAN 802.11a/b/g measurement application (Requires Opt. SVE) (For models of bandwidth ≥2.5 GHz only)
WLAN 802.11n measurement application (Requires Opt. SVE and SV23) (For models of bandwidth ≥2.5 GHz only)
®
SignalVu APCO P25 measurements (Requires Opt. SVE)
®
SignalVu Bluetooth Basic LE TX SIG measurements (Requires Opt. SVE) (For models of bandwidth ≥2.5 GHz only)
®
SignalVu LTE Downlink RF measurements (Requires Opt. SVE) (For models of bandwidth ≥1 GHz only)
USB 2.0 Automated Compliance Test Application (Requires TDSUSBF USB Test Fixture) ≥2 GHz bandwidth required for high-
speed USB.
DPOFL-USBPWR
DPOFL-XGBT2
Automated compliance test solution for USB power adapters
TekExpress Automated 10GBASE-T Compliance Test Software (Requires TF-XGbt Test Fixture) (For DPO7354C model only)
Power plug options
Opt. A0
North America power plug (115 V, 60 Hz)
Universal Euro power plug (220 V, 50 Hz)
United Kingdom power plug (240 V, 50 Hz)
Australia power plug (240 V, 50 Hz)
Switzerland power plug (220 V, 50 Hz)
Japan power plug (100 V, 50/60 Hz)
China power plug (50 Hz)
Opt. A1
Opt. A2
Opt. A3
Opt. A5
Opt. A6
Opt. A10
Opt. A11
India power plug (50 Hz)
Opt. A12
Brazil power plug (60 Hz)
Opt. A99
No power cord
www.tek.com/DPO7000 23
Datasheet
Language options
Opt. L0
English manual
Opt. L1
French manual
Opt. L3
German manual
Opt. L5
Japanese manual
Simplified Chinese manual
Traditional Chinese manual
Korean manual
Opt. L7
Opt. L8
Opt. L9
Opt. L10
Russian manual
Service options
Opt. C3
Calibration Service 3 Years
Opt. C5
Calibration Service 5 Years
Opt. D1
Calibration Data Report
Opt. D3
Calibration Data Report 3 Years (with Opt. C3)
Calibration Data Report 5 Years (with Opt. C5)
Repair Service 3 Years (including warranty)
Repair Service 5 Years (including warranty)
Opt. D5
Opt. R3
Opt. R5
Probes and accessories are not covered by the oscilloscope warranty and Service Offerings. Refer to the datasheet of each probe and accessory model for its unique warranty
and calibration terms.
Recommended accessories
Probes
Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please
visit www.tek.com/probes.
TAP3500
3.5 GHz TekVPI active single-ended probe
TAP2500
TAP1500
TDP3500
TDP1500
TDP1000
TDP0500
TIVM1
2.5 GHz TekVPI active single-ended probe
1.5 GHz TekVPI active single-ended probe
3.5 GHz TekVPI differential voltage probe with ±2 V differential input voltage
1.5 GHz TekVPI differential voltage probe with ±8.5 V differential input voltage
1 GHz TekVPI differential voltage probe with ±42 V differential input voltage
500 MHz TekVPI differential voltage probe with ±42 V differential input voltage
Differential Probe; 1 GHz, Up to 50X, ±50 V, TekVPI, 3 Meter Cable
Differential Probe; 1 GHz, Up to 50X, ±50 V, TekVPI, 10 Meter Cable
Differential Probe; 800 MHz, Up to 1000X, > 1000 V, TekVPI, 3 Meter Cable
Differential Probe; 800 MHz, Up to 1000X, > 1000 V, TekVPI, 10 Meter Cable
Differential Probe; 500 MHz, Up to 1000X, > 1000 V, TekVPI, 3 Meter Cable
Differential Probe; 500 MHz, Up to 1000X, > 1000 V, TekVPI, 10 Meter Cable
Differential Probe; 200 MHz, Up to 1000X, > 1000 V, TekVPI, 3 Meter Cable
Differential Probe; 200 MHz, Up to 1000X, > 1000 V, TekVPI, 10 Meter Cable
TIVM1L
TIVH08
TIVH08L
TIVH05
TIVH05L
TIVH02
TIVH02L
TCP0150
TCP0030A
TCP0020
™
20 MHz TekVPI 150 Ampere AC/DC current probe
120 MHz TekVPI 30 Ampere AC/DC current probe
50 MHz TekVPI 20 Ampere AC/DC current probe
24 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
TRCP0300
TRCP0600
TRCP3000
TMDP0200
THDP0200
THDP0100
P5100A
30 MHz, 250 mA to 300 A, AC current probe
30 MHz, 500 mA to 600 A, AC current probe
16 MHz, 500 mA to 3000 A, AC current probe
±750 V, 200 MHz high-voltage differential probe
±1.5 kV, 200 MHz high-voltage differential probe
±6 kV, 100 MHz high-voltage differential probe
2.5 kV, 500 MHz, 100X high-voltage passive probe
20 kV, 75 MHz high-voltage passive probe
P6015A
Accessories
077-0076-xx
077-0010-xx
077-0063-xx
016-1985-xx
119-7275-xx
016-1970-xx
020-3071-xx
DPO7AFP
Service Manual, pdf on hard drive (pdf only)
Programmer Manual (pdf only)
Performance Verification and Specification (pdf only)
Rackmount Kit
Mini multimedia keyboard
Transit Case
DPO Demo 3 board with dual-A to single-B USB cable
Auxiliary front panel
Cables
012-0991-xx
012-0991-xx
GPIB Cable (1 m)
GPIB Cable (2 m)
Test fixtures
067-1686-xx
TDSUSBF
Probe Calibration / Power Deskew Test Fixture
Test Fixture for use with Opt. USB2
TF-BRR-CFD
TF-GBE-ATP
Automotive Ethernet Compliance Clock Frequency Divider fixture
10/100/1000BASE-T Advanced Test Package (consists of test fixture PCB set, RJ45 interconnect cable, and 1000BASE-T jitter
test channel cable)
TF-GBE-BTP
TF-GBE-EE
10/100/1000BASE-T Basic Test Package (consists of test fixture PCB set and RJ45 interconnect cable)
Additional test fixture for Energy Efficient Ethernet measurements. Order through Crescent Heart Software (http://www.c-h-s.com)
Adapters
TPA-BNC
P6701B
TekVPI-to-TekProbe BNC Adapter
®
Optical/Electrical Converter (Multi Mode). Requires TekVPI to TekProbe BNC adapter (TPA-BNC).
®
P6703B
Optical/Electrical Converter (Single Mode). Requires TekVPI to TekProbe BNC adapter (TPA-BNC).
Software
™
TekScopeNL-BAS
TekScope Anywhere Waveform Analysis and Visualization Node locked license.
™
TekScopeFL-BAS
TekScopeNL-DJA
TekScopeFL-DJA
GRL-USB-PD
TekScope Anywhere Waveform Analysis and Visualization floating license.
™
Advanced Jitter Analysis for TekScope Anywhere Node locked license.
™
Advanced Jitter Analysis for TekScope Anywhere floating license.
USB Power Delivery electrical compliance and decode.
www.tek.com/DPO7000 25
Datasheet
Upgrade options
To upgrade your DPO7000C Series oscilloscope, order DPO-UP and option listed below. For example, to add option DDRA, DDR Memory Technology Analysis Package,
order DPO-UP DDRA.
To upgrade record length:
RL25
From standard 25M/channel configuration to Opt. 5RL configuration
From standard 25M/channel configuration to Opt. 10RL configuration
From Opt. 5RL configuration to Opt. 10RL configuration
RL210
RL510
To add a Solid State Hard Disk
Drive:
SSD
Add an additional customer-installable removable Solid State Drive assembly with Microsoft Windows 7 OS, TekScope, and
applications software installed
DPO7SSD-W10
Add an additional customer-installable removable Solid State Drive assembly with Microsoft Windows 10 OS, TekScope, and
applications software installed. Note: order DPO7SSD-W10, do not order DPO-UP for this SSD.
To add Hard Disk Drive:
HDD7
Hard Disk Drive, at least 500 GB, removable, with Windows 7 OS, TekScope software and applications software installed
To upgrade DPO7000C Series
with:
BRR
Add Opt. BRR - BroadR-Reach/100BASE-T1 and 1000BASE-T1 Compliance Testing (Requires TF-GBE-BTP and TF-BRR-CFD
Test Fixtures) (For models of bandwidth ≥1 GHz only)
DDRA
DJAM
DJAN
D-PHY
Add Option DDRA (Requires Opt. DJA) (For models of bandwidth ≥1 GHz only)
Add Opt. DJA – Jitter and Eye Analysis Tools - Advanced (DPOJET)
Add Opt. DJAN - DPOJET Noise, jitter, and eye analysis tools (Requires Opt. DJA)
®
Add Opt. D-PHY – MIPI D-PHY Transmitter Debug, Characterization, and Compliance Test Solution (Requires Opt. DJA) (For
models of bandwidth ≥2.5 GHz only)
ET3
Add Opt. ET3 – Ethernet Compliance Testing (Requires TF-GBE-BTP or TF-GBE-ATP Ethernet Test Fixture)
MOST
Add Opt. MOST – MOST Essentials - Electrical Compliance and Debug Test Solution for MOST50 and MOST150 (Requires Opt.
DJA)
MTM
Add Opt. MTM – Mask Testing
NBASE-T
Add Opt. NBASE-T TekExpress Automated NBASE-T and IEEE802.3bz (2.5G and 5G) Compliance Test Software (Requires TF-
XGbt Test Fixture) (For models of bandwidth ≥2.5 GHz only)
PWR
Add Opt. PWR – Power Measurement and Analysis
SR-AERO
Add Opt. SR-AERO – Aerospace Serial Triggering and Analysis (MIL-STD-1553). Enables triggering on packet-level information
on MIL-STD-1553 buses as well as analytical tools such as digital views of the signal, bus views, and packet decoding
SR-AUTO
Add Opt. SR-AUTO – Automotive Serial Triggering and Analysis (CAN/LIN/FlexRay). Enables triggering on packet-level
information on CAN, LIN, and FlexRay buses as well as analytical tools such as digital views of the signal, bus views, and packet
decoding
SR-COMP
SR-DPHY
SR-EMBD
SR-ENET
SR-PCIE
Add Opt. SR-COMP – Computer Serial Triggering and Analysis (RS-232/422/485/UART)
®
Add Opt. SR-DPHY – MIPI D-PHY Serial Analysis (DSI-1 and CSI-2)
Add Opt. SR-EMBD – Embedded Serial Triggering and Analysis (I2C, SPI)
Add Opt. SR-ENET – Ethernet Serial Analysis (10BASE-T, 100BASE-TX)
Add Opt. SR-PCIE – PCI Express Serial Analysis. Enables analysis of PCI Express buses with analytical tools such as digital
views of the signal, bus views, and packet decoding (For models of bandwidth ≥1 GHz only) ( Due to large volumes of data, use of
standard high-capacity hard drive rather than the smaller SSD is recommended.)
SR-USB
SR-810B
Add Opt. SR-USB – USB 2.0 Serial Triggering and Analysis (LS, FS, HS)
Add Opt. SR-810B – 8b/10b Serial Analysis. Enables analysis of 8b/10b buses with analytical tools such as digital views of the
signal, bus views, and packet decoding
SSD
Add Opt. SSD – Solid State Hard Drive
ST1G
Add Opt. ST1G – 64-bit NRZ Serial Trigger and 8b/10b Serial Protocol Decode (includes Opt. SR-810B) (For models of bandwidth
≥2.5 GHz only)
26 www.tek.com/DPO7000
DPO7000C Series Datasheet - DPO7000C Series
SVEM
SVA
SVM
SVO
SVP
Add Opt. SVE – SignalVu Essentials Vector Signal Analysis
Add Opt. SVA – SignalVu AM/FM/Direct Audio Measurements (Requires Opt. SVE)
Add Opt. SVM – SignalVu General Purpose Modulation Analysis (Requires Opt. SVE)
Add Opt. SVO– SignalVu Flexible OFDM Analysis (Requires Opt. SVE)
Add Opt. SVP – SignalVu Pulse Advanced Signal Analysis (Requires Opt. SVE)
SVT
Add Opt. SVT – SignalVu Settling Time Measurements - Frequency and Phase (Requires Opt. SVE)
Add Opt. SV23 - WLAN 802.11a/b/g measurement application (Requires Opt. SVE) (For models of bandwidth ≥2.5 GHz only)
SV23
SV24
Add Opt. SV24 - WLAN 802.11n measurement application (Requires Opt. SVE and SV23) (For models of bandwidth ≥2.5 GHz
only)
®
SV26
SV27
Add Opt. SV26 - SignalVu APCO P25 measurements (Requires Opt. SVE)
®
Add Opt. SV27- SignalVu Bluetooth Basic LE TX SIG measurements (Requires Opt. SVE) (For models of bandwidth ≥2.5 GHz
only)
®
SV28
USB2
Add Opt.SV28 - SignalVu LTE Downlink RF measurements (Requires Opt. SVE) (For models of bandwidth ≥1 GHz only)
Add Opt. USB2 – USB 2.0 Automated Compliance Test Application (Requires TDSUSBF (USB Test Fixture). ≥2 GHz bandwidth
required for high-speed USB)
USBPWR
XGBT2
Add Opt. USBPWR - Automated compliance test solution for USB power adapters
Add Opt. XGBT2 - TekExpress Automated 10GBASE-T Compliance Test Software (Requires TF-XGbt Test Fixture) (For
DPO7354C model only)
Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.
www.tek.com/DPO7000 27
Datasheet
ASEAN / Australasia (65) 6356 3900
Belgium 00800 2255 4835*
Austria 00800 2255 4835*
Brazil +55 (11) 3759 7627
Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777
Canada 1 800 833 9200
Central East Europe and the Baltics +41 52 675 3777
Finland +41 52 675 3777
Central Europe & Greece +41 52 675 3777
France 00800 2255 4835*
Denmark +45 80 88 1401
Germany 00800 2255 4835*
Hong Kong 400 820 5835
India 000 800 650 1835
Italy 00800 2255 4835*
Japan 81 (3) 6714 3086
Luxembourg +41 52 675 3777
The Netherlands 00800 2255 4835*
Poland +41 52 675 3777
Russia & CIS +7 (495) 6647564
Sweden 00800 2255 4835*
Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90
Norway 800 16098
Portugal 80 08 12370
South Africa +41 52 675 3777
Switzerland 00800 2255 4835*
USA 1 800 833 9200
Middle East, Asia, and North Africa +41 52 675 3777
People's Republic of China 400 820 5835
Republic of Korea +822 6917 5084, 822 6917 5080
Spain 00800 2255 4835*
Taiwan 886 (2) 2656 6688
United Kingdom & Ireland 00800 2255 4835*
* European toll-free number. If not accessible, call: +41 52 675 3777
For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tek.com.
©
Copyright Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and
price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.
12 Jun 2018 48W-26543-21
www.tek.com/DPO7000
相关型号：
©2020 ICPDF网 联系我们和版权申明