172D-3 [TELEDYNE]
DPDT basic relay;型号: | 172D-3 |
厂家: | TELEDYNE TECHNOLOGIES INCORPORATED |
描述: | DPDT basic relay 光电二极管 继电器 |
文件: | 总5页 (文件大小:252K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SERIES
CENTIGRID®
COMMERCIAL RELAYS
DPDT
172
SERIES
DESIGNATION
RELAY TYPE
172
DPDT basic relay
172D
DPDT relay with internal diode for coil transient suppression
INTERNAL CONSTRUCTION
DESCRIPTION
The 172 Centigrid® relay is an ultraminiature, hermetically sealed, armature
relay for commercial applications. Its low profile height (.280") and .100" grid
spaced terminals, which preclude the need for spreader pads, make it an ideal
choice where extreme packaging density and/or close PC board spacing are
required.
UPPER
STATIONARY
CONTACT
UNI-FRAME
ARMATURE
LOWER
STATIONARY
CONTACT
MOVING
CONTACT
The basic operating concept and internal structure are similar to Teledyne’s
DPDT 114 Centigrid® relay. Unique construction features and manufacturing
techniques provide overall high reliability and excellent resistance to
environmental extremes:
• All welded construction.
• Unique uni-frame design providing high magnetic efficiency and mechanical
rigidity.
• High force/mass ratios for resistance to shock and vibration.
• Advanced cleaning techniques provide maximum assurance of internal
cleanliness.
• Precious metal alloy contact material with gold plating assures excellent
high current and dry circuit switching capabilities.
ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
The Series 172 relay has an internal discrete silicon diode for coil transient
suppression.
Storage
–65°C to +125°C
–55°C to +85°C
Temperature
(Ambient)
Operating
Vibration
(General Note 1)
By virtue of its inherently low intercontact capacitance and contact circuit
losses, the 172 relay is an excellent subminiature RF switch for frequencies
well into the UHF spectrum (see Figure 1). Applications include
telecommunications, test instruments, mobile communications, attenuators,
and automatic test equipment.
10 g’s to 500 Hz
Shock
(General Note 1)
30 g’s,
6 msec, half-sine
Enclosure
Weight
Hermetically sealed
0.15 oz. (4.3g) max.
©2007 TELEDYNE RELAYS
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
172 Page 1
172/0107/Q1
SERIES 172
GENERAL ELECTRICAL SPECIFICATIONS (@25°C) (Notes 2 & 3)
Contact Arrangement
Rated Duty
2 Form C (DPDT)
Continuous
Contact Resistance
0.15 ohm max. before life; 0.3 ohm max. after life at 1A/28Vdc (measured 1/8" from header)
Resistive:
Inductive:
Lamp:
1 Amp/28Vdc
200 mA/28Vdc (320 mH)
100 mA/28Vdc
Contact Load Ratings (DC)
(See Fig. 1 for other DC
resistive voltage/current ratings)
Low Level:
10 to 50 µA/10 to 50mV
5,000,000 cycles (typical) at low level
Contact Life Ratings
500,000 cycles (typical) at 0.5A/28Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Overload Rating
Contact Carry Rating
Operate Time
2A/28Vdc Resistive (100 cycles min.)
Contact factory
6.0 msec max. at nominal rated coil voltage
172: 3.0 msec max. 172D: 6.0 msec max.
0.4 pf typical
Release Time
Intercontact Capacitance
Insulation Resistance
Dielectric Strength
Negative Coil Transient 172
Diode P.I.V. 172D
1,000 megohms min. between mutually isolated terminals
Atmospheric pressure: 300 Vrms/60Hz
2.0 Vdc Max.
60 Vdc Min.
DETAILED ELECTRICAL SPECIFICATIONS (@25°C) (Note 3)
172-3
172D-3
172-5
172D-5
172-12
172D-12
172-26
172D-26
BASE PART
NUMBERS
Nom.
Max.
3.0
3.6
5.0
5.8
64
12.0
16.0
400
9.0
26.5
32.0
1600
18.0
440
Coil Voltage (Vdc)
Coil Resistance (Ohms ±20%)
39
Pick-up Voltage (Vdc, Max.) Pulse Operation
2.25
235
3.8
405
Coil Operating Power at Nominal Voltage (Milliwatts)
360
OUTLINE DIMENSIONS (Note 4)
SCHEMATIC DIAGRAM
TERMINAL LOCATIONS
(Viewed from Terminals, Numbers for Reference Only)
.750 MIN.
.280 MAX
(19.05)
.031 REF
(.79)
.035 REF
(.89)
(7.11)
7
6
8
1
.335 SQ MAX.
(8.51)
2
172
.100 ±.010 TYP
(2.54 ±.25)
3
5
4
+.002
.017
(.43
DIA
–.001
.375
SQ MAX.
(8.51)
+.05
)
–.03
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
172D
SCHEMATIC IS VIEWED FROM TERMINALS
GENERAL NOTES
PERFORMANCE CURVES (Note 2)
1. Relay contacts will exhibit no chatter in
excess of 10 µsec or transfer in excess
of 1 µsec.
2. “Typical” characteristics are based on
available data and are best estimates.
No on-going verification tests are
performed.
3. Unless otherwise specified, parameters
are initial values.
4. Relays can be supplied with a spacer
pad. See appendix.
TYPICAL RF PERFORMANCE
TYPICAL DC CONTACT RATING (RESISTIVE)
0
.1
.2
.3
.4
300
250
200
10
20
30
40
50
60
70
1.92
1.22
1.07
1.02
1.01
1.00
1.00
150
100
50
0
0.1 0.2 0.3 0.4 0.5
0.6
0.7 0.8
0.9 1.0
.01
0.5
.1
.5
1.0
LOAD CURRENT (AMPS DC)
FREQUENCY (GHz)
FIGURE 2
FIGURE 1
172 Page 2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
©2007 TELEDYNE RELAYS
172/0107/Q1
Appendix A: Spacer Pads
Pad designation and
bottom view dimensions
Dim. H
Max.
Height
For use with the following:
ER411T
ER412, ER412D, ER412DD
.295 (7.49)
Ø.150
[3.81]
(REF)
712, 712D, 712TN,
RF300, RF310, RF320
.300 (7.62)
Dim
H
MAX
ER420, ER422D, ER420DD, 421,
ER421D, ER421DD, ER422, ER422D, .305 (7.75)
ER422DD, 722, 722D, RF341
ER431T, ER432T,
.400 (10.16)
ER432, ER432D, ER432DD
732, 732D, 732TN, RF303, RF313,
.410 (10.41)
RF323
RF312
.350 (8.89)
“M4” Pad for TO-5
ER411, ER411D, ER411DD
.295 (7.49)
Dim
H
MAX
ER431, ER431D, ER431DD
RF311
.400 (10.16)
.300 (7.62)
RF331
.410 (10.41)
.305 (7.75)
“M4” Pad for TO-5
172, 172D
ER114, ER114D, ER114DD,
J114, J114D, J114DD
Dim
H
MAX
.300 (7.62)
ER134, ER134D, ER134DD,
J134, J134D, J134DD
.400 (10.16)
RF100
RF103
.315 (8.00)
“M4” Pad for Centigrid®
.420 (10.67)
.156
[3.96]
(REF)
122C, A152
.320 (8.13)
.300 (7.62)
Dim
MAX
H
ER116C, J116C
.256
[6.5]
(REF)
ER136C, J136C
RF180
.400 (10.16)
.325 (8.25)
.305 (7.75)
A150
“M9” Pad for Centigrid®
Notes:
1. Spacer pad material: Polyester film.
2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering
example in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise specified, tolerance is ± .010 (.25).
5. Add 10 mΩ to the contact resistance show in the datasheet.
6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
© 2008 Teledyne Relays
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Appendix A: Spreader Pads
Pad designation and
bottom view dimensions
Dim. H
Max.
Height
For use with the following:
ER411T, J411T, ER412, ER412D
ER412DD, J412, J412D, J412DD
ER412T, J412T
.370 [9.4]
MAX SQ
.388 (9.86)
.393 (9.99)
.493 (12.52)
.503 (12.78)
.100
[2.54]
Dim
MAX
H
712, 712D, 712TN
.150
[3.81]
.014
[0.36]
(REF)
ER431T, J431T, ER432, ER432D
ER432DD, J432, J432D, J432DD
ER432T, J432T
.300
[7.62]
.100
[2.54]
732, 732D, 732TN
.370
[9.4]
MIN
ER420, J420, ER420D, J420D
ER420DD, J420DD, ER421, J421
ER421D, J421D, ER421DD
.200
[5.08]
.398 (10.11)
J422D, ER422DD, J422DD, 722
“M” Pad 5/ 6/
.390 [9.91]
SQ
ER411T
.100
[2.54]
ER412, ER412D, ER412DD
J412, J412D, J412DD
.441 (11.20)
.100
[2.54]
.150
[3.81]
Dim
MAX
H
712, 712D
.451 (11.46)
.451 (11.46)
.300
[7.62]
ER421, ER421D, ER421DD
722, 732D
ER431T
ER432, ER432D, ER432DD
.130
[3.3]
.150
[3.81]
.546 (13.87)
.556 (14.12)
.300
[7.62]
732, 732D
“M2” Pad 7/ 8/
ER411, ER411D, ER411DD
ER411TX
ER412X, ER412DX, ER412DDX
ER412TX
.388 (9.86)
.393 (9.99)
.398 (10.11)
.370 [9.4]
MAX SQ
.100
[2.54]
712X, 712DX, 712TNX
Dim
MAX
H
ER420X, ER420DX, ER420DDX
ER421X, ER421DX, ER421DDX
ER422X, ER422DX
.150
[3.81]
.014
[0.36]
(REF)
.300
[7.62]
.100
[2.54]
ER422DDX, 722X, 722DDX
.370
[9.4]
MIN
ER431, ER431D, ER431DD
ER431TX
.200
[5.08]
.493 (12.52)
.503 (12.78)
ER432X, ER432DX, ER432DDX
ER432TX
“M3” Pad 5/ 6/ 9/
732X, 732DX, 732TNX
Notes:
1. Spreader pad material: Diallyl Phthalate.
2. To specify an “M”, “M2” or “M3” spreader pad, refer to the mounting variants portion of the part number example
in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise specified, tolerance is ± .010” (0.25).
5/. Add 25 mΩ to the contact resistance shown in the datasheet.
6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
7/. Add 50 mΩ to the contact resistance shown in the datasheet.
8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet.
9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.)
(800) 284-7007 • www.teledynerelays.com
♦
+44 (0) 1236 453124 • www.teledyne-europe.com
© 2008 Teledyne Relays
Appendix A: Ground Pin Positions
"Z" POSITION
"X" POSITION
"Z" POSITION
Ø.200
[Ø5.08]
Ø.200
[Ø5.08]
"Y" POSITION
45°±3°
"Y" POSITION
36°±3°
TO-5 Relays:
TO-5 Relays:
ER411T, ER412, ER412T, ER420, ER421, ER422,
ER431T, ER432, ER432T, 712, 712TN, 400H, 400K,
400V, RF300, RF303, RF341, RF312, RF310, RF313,
RF320, RF323
ER411, ER431, RF311, RF331
"Y" POSITION
.100
[2.54]
"Y" POSITION
"Z" POSITION
"W" POSITION
"Z" POSITION
.100
[2.54]
.100
[2.54]
.050
.100
[1.27]
[2.54]
"X" POSITION
"U" POSITION
(ER116C and ER136C only)
.100
[2.54]
.100
[2.54]
Centigrid® Relays:
Centigrid® Relays:
RF180, ER116C, 122C, ER136C
RF100, RF103, ER114, ER134, 172
NOTES
1. Terminal views shown
2. Dimensions are in inches (mm)
Indicates ground pin position
3. Tolerances: ± .010 (±.25) unless otherwise specified
4. Ground pin positions are within .015 (0.38) dia. of true position
5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref.
6. Lead dia. 0.017 (0.43) nom.
Indicates glass insulated lead position
Indicates ground pin or lead position
depending on relay type
© 2008 Teledyne Relays
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
相关型号:
©2020 ICPDF网 联系我们和版权申明